Scalable conductive polymer membranes for ultrafast organic pollutants removal

Electric field-confined synthesis of single atomic TiOxCy electrocatalytic membranes

Electrocatalysis exhibits certain benefits for water purification, but the low performance of electrodes severely hampers its utility. Here, we report a general strategy for fabricating high-performance three-dimensional (3D) porous electrodes with ultrahigh electrochemical active surface area and single-atom catalysts from earth-abundant elements. We demonstrate a binder-free dual electrospinning-electrospraying (DESP) strategy to densely distribute single atomic Ti and titanium oxycarbide (TiOxCy) sub-3-nm clusters throughout interconnected carbon nanofibers (CNs). The composite offers ultrahigh conductivity and mechanical robustness (ultrasonication resistant). The resulting TiOxCy filtration membrane exhibits record-high water purification capability with excellent permeability (~8370 liter m-2 hour-1 bar-1), energy efficiency (e.g., >99% removal of toxins within 1.25 s at 0.022 kWh·m-3 per order), and erosion resistance. The hierarchical design of the TiOxCy membrane facilitates rapid and energy-efficient electrocatalysis through both direct electron transfer and indirect reactive oxygen species (1O2, ·OH, and O2·-, etc.) oxidations. The electric field-confined DESP strategy provides a general platform for making high-performance 3D electrodes.

Harnessing Electrochemistry Synergy in Reverse Osmosis: Modulating Ammonium Localized Oxidation and Restricted Transport

The unsatisfactory selectivity of reverse osmosis (RO) membranes toward ammonium poses a critical challenge in water safety when reclaiming water from domestic wastewater. Herein, we developed a novel integrated electrochemical-assisted RO (ECRO) system using the electrically treated feed spacer and permeate carrier as electrodes. This system enhanced ammonium removal efficiency significantly while maintaining low energy consumption, increasing from 94.36% at 0 V to 99.91% at 4 V. The improvement was primarily attributed to localized oxidation and restricted transport of ammonium ions. Specifically, the permeate carrier anode facilitated the indirect oxidation of ammonium through active chlorine via the breakpoint chlorination pathway, notably localized on the permeate side to prevent damage to the separation layer of the RO membrane and simultaneously avoid additional chemical additives. Furthermore, the restricted ammonium ion transport was responsible for its improved enthalpic barrier, as evidenced by both experimental investigation and Monte Carlo simulation. This rise in enthalpic barrier was primarily driven by the reverse electric field force across the RO membrane, coupled with the constrained ion migration near the membrane surface and ion diffusion within the membrane. This study offers new insights and a theoretical foundation for the optimization of electrochemistry synergy membrane systems, highlighting the potential for enhancing ammonium removal in wastewater reclamation in a green and low-energy manner.

Reconstructing Electrically Conductive Nanofiltration Membranes with an Aniline-Functionalized Carbon Nanotubes Interlayer for Highly Effective Toxic Organic Treatment

Conductive nanofiltration (CNF) membranes hold great promise for removing small organic pollutants from water through enhanced Donnan exclusion and electrocatalytic degradation. However, current CNF membranes face limitations in conductivity, structural stability, and nanochannel control strategies. This work addresses these challenges by introducing aniline-functionalized carbon nanotubes (NH2-CNTs) as an interlayer. NH2-CNTs enhance the dispersibility and adhesion of pristine carbon nanotubes, leading to a more conductive and stable composite nanofiltration membrane. The redesigned NH2-CNTs interlayered conductive nanofiltration (NICNF) membrane exhibits a 10-fold increase in conductivity and a high response degree (80%) with excellent cyclic stability, surpassing existing CNF membranes. The synergistic effects of enhanced Donnan exclusion, voltage switching, and electrocatalysis enable the NICNF membrane to achieve selective recovery of mixed dyes, 98.97% removal of residual wastewater toxicity, and a 5.2-fold increase in permeance compared to the commercial NF270 membrane. This research paves the way for next-generation multifunctional membranes capable of the efficient recovery and degradation of toxic organic pollutants in wastewater.

Electrochemical filtration for drinking water purification: A review on membrane materials, mechanisms and roles

Electrochemical filtration can not only enrich low concentrations of pollutants but also produce reactive oxygen species to interact with toxic pollutants with the assistance of a power supply, making it an effective strategy for drinking water purification. In addition, the application of electrochemical filtration facilitates the reduction of pretreatment procedures and the use of chemicals, which has outstanding potential for maximizing process simplicity and reducing operating costs, enabling the production of safe drinking water in smaller installations. In recent years, the research on electrochemical filtration has gradually increased, but there has been a lack of attention on its application in the removal of low concentrations of pollutants from low conductivity water. In this review, membrane substrates and electrocatalysts used to improve the performance of electrochemical membranes are briefly summarized. Meanwhile, the application prospects of emerging single-atom catalysts in electrochemical filtration are also presented. Thereafter, several electrochemical advanced oxidation processes coupled with membrane filtration are described, and the related working mechanisms and their advantages and shortcomings used in drinking water purification are illustrated. Finally, the roles of electrochemical filtration in drinking water purification are presented, and the main problems and future perspectives of electrochemical filtration in the removal of low concentration pollutants are discussed.

Ionic Hyperbranched Poly(amido-amine)-Incorporated Nanofiltration Membranes for High-Efficiency Dye Desalination

High-efficiency dye desalination is crucial in the textile industry, considering its importance for human health, safe aquatic ecological systems, and resource recovery. In order to solve the problem of effective separation of univalent salt and ionic dye under the condition of high salt, ionic hyperbranched poly(amido-amine) (HBPs) were synthesized based on a simple and scalable one-step polycondensation method and then incorporated into the polyamide (PA) selective layers to construct charged nanochannels through interfacial polymerization (IP) on the surface of a polyvinyl chloride ultrafiltration (PVC-UF) hollow fiber membrane. Both the internal nanopores of HBPs (internal nanochannels) and the interfacial voids between HBPs and the PA matrix (external nanochannels) can be regarded as a fast water molecule transport pathway, while the terminal ionic groups of ionic HBPs endow the nanochannels with charge characteristics for improving ionic dye/salt selectivities. The permeate fluxes and dye/salt selectivities of HBP-TAC/PIP (57.3 L m-2 h-1 and rhodamine B (RB)/NaCl selectivity of 224.0) and HBP-PS/PIP (63.7 L m-2 h-1 and lemon yellow (LY)/NaCl selectivity of 664.0) membranes under 0.4 MPa operation pressure are much higher than PIP-only and HBP-NH2/PIP membranes. At the same time, this project also studied the membrane desalination process in a simulated high-salinity dye/salt mixture system to provide a theoretical basis and technical support for the actual dye desalination process.

Thin Film Nanocomposite Membranes Based on Zeolitic Imidazolate Framework-8/Halloysite Nanotube Composites

Thin film nanocomposite (TFN) membranes have proven their unrivaled value, as they can combine the advantages of different materials and furnish membranes with improved selectivity and permeability. The development of TFN membranes has been severely limited by the poor dispersion of the nanoparticles and the weak adhesion between the nanoparticles and the polymer matrix. In this study, to address the poor dispersion of nanoparticles in TFN membranes, we proposed a new combination of m-ZIF-8 and m-HNTs, wherein the ZIF-8 and HNTs were modified with poly (sodium p-styrenesulfonate) to enhance their dispersion in water. Furthermore, the hydropathic properties of the membranes can be well controlled by adjusting the content of m-ZIF-8 and m-HNTs. A series of modified m-ZIF-8/m-HNT/PAN membranes were prepared to modulate the dye/salt separation performance of TFN membranes. The experimental results showed that our m-ZIF-8/m-HNT/PAN membranes can elevate the water flux significantly up to 42.6 L m-2 h-1 MPa-1, together with a high rejection of Reactive Red 49 (more than 80%). In particular, the optimized NFM-7.5 membrane that contained 7.5 mg of HNTs and 2.5 mg of ZIF-8 showed a 97.1% rejection of Reactive Red 49 and 21.3% retention of NaCl.

New Insights on Designing the Next-Generation Materials for Electrochemical Synthesis of Reactive Oxidative Species Towards Efficient and Scalable Water Treatment: A Review and Perspectives

Electrochemical water remediation technologies offer several advantages and flexibility for water treatment and degradation of contaminants. These technologies generate reactive oxidative species (ROS) that degrade pollutants. For the implementation of these technologies at an industrial scale, efficient, scalable, and cost-effective in-situ ROS synthesis is necessary to degrade complex pollutant mixtures, treat large amount of contaminated water, and clean water in a reasonable amount of time and cost. These targets are directly dependent on the materials used to generate the ROS, such as electrodes and catalysts. Here, we review the key design aspects of electrocatalytic materials for efficient in-situ ROS generation. We present a mechanistic understanding of ROS generation, including their reaction pathways, and integrate this with the key design considerations of the materials and the overall electrochemical reactor/cell. This involves tunning the interfacial interactions between the electrolyte and electrode which can enhance the ROS generation rate up to ~ 40% as discussed in this review. We also summarized the current and emerging materials for water remediation cells and created a structured dataset of about 500 electrodes and 130 catalysts used for ROS generation and water treatment. A perspective on accelerating the discovery and designing of the next generation electrocatalytic materials is discussed through the application of integrated experimental and computational workflows. Overall, this article provides a comprehensive review and perspectives on designing and discovering materials for ROS synthesis, which are critical not only for successful implementation of electrochemical water remediation technologies but also for other electrochemical applications.

Carbonized Leather Waste with Deposited Polypyrrole Nanotubes: Conductivity and Dye Adsorption

This paper reports the conversion of a waste to a conducting material, exploiting the ability to adsorb pollutant organic dyes. Leather waste was carbonized at 800 °C in an inert nitrogen atmosphere. The resulting biochar was used for in-situ deposition of polypyrrole nanotubes produced by the oxidative polymerization of pyrrole in the presence of methyl orange. The composites of carbonized leather with deposited polypyrrole nanotubes of various composition were compared with similar composites based on globular polypyrrole. Their molecular structure was characterized by infrared and Raman spectra. Both conducting components formed a bicontinuous structure. The resistivity was newly determined by a four-point van der Pauw method and monitored as a function of pressure applied up to 10 MPa. The typical conductivity of composites was of the order of 0.1 to 1 S cm-1 and it was always higher for polypyrrole nanotubes than for globular polypyrrole. The method also allows for the assessment of mechanical features, such as powder fluffiness. The conductivity decreased by 1-2 orders of magnitude after treatment with ammonia but still maintained a level acceptable for applications operating under non-acidic conditions. The composites were tested for dye adsorption, specifically cationic methylene blue and anionic methyl orange, using UV-vis spectroscopy. The composites were designed for future use as functional adsorbents controlled by the electrical potential or organic electrode materials.

Electroactive membrane with the electroactive layer beneath the separation layer to eliminate the interference of humic acid in the oxidation of antibiotics

Removing harmful antibiotics is essential to reclaiming water from municipal secondary effluent. Electroactive membranes are effective in the removal of antibiotics but challenged by the abundant coexisting macromolecular organic pollutants in municipal secondary effluent. To eliminate the interference of macromolecular organic pollutants in the removal of antibiotics, we propose a novel electroactive membrane with a top polyacrylonitrile (PAN) ultrafiltration layer and a bottom electroactive layer composed of carbon nanotubes (CNTs) and polyaniline (PANi). When filtering the mixture of tetracycline (TC, a typical antibiotic) and humic acid (HA, a typical macromolecular organic pollutant), the PAN-CNT/PANi membrane performed sequential removal. It retained HA at the PAN layer (by ∼96%) and allowed TC to reach the electroactive layer where it was electrochemically oxidized (e.g., by ∼92% at 1.5 V). The TC removal of the PAN-CNT/PANi membrane was marginally affected by HA, unlike that of the control membrane with the electroactive layer on the top that showed decreased TC removal after the addition of HA (e.g., decreased by 13.2% at 1 V). The decreased TC removal of the control membrane was attributed to the attachment (but not competitive oxidation) of HA on the electroactive layer that impaired the electrochemical reactivity. The HA removal prior to TC degradation realized by the PAN-CNT/PANi membrane avoided the attachment of HA and guaranteed TC removal on the electroactive layer. Long-term filtration for 9 h revealed the stability of the PAN-CNT/PANi membrane, and its advantageous structural design was conformed in the context of real secondary effluents.

Quantification of interfacial interaction related with adhesive membrane fouling by genetic algorithm back propagation (GABP) neural network

Since adhesive membrane fouling is critically determined by the interfacial interaction between a foulant and a rough membrane surface, efficient quantification of the interfacial interaction is critically important for adhesive membrane fouling mitigation. As a current available method, the advanced extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory involves complicated rigorous thermodynamic equations and massive amounts of computation, restricting its application. To solve this problem, artificial intelligence (AI) visualization technology was used to analyze the existing literature, and the genetic algorithm back propagation (GABP) artificial neural network (ANN) was employed to simplify thermodynamic calculation. The results showed that GABP ANN with 5 neurons could obtain reliable prediction performance in seconds, versus several hours or even days time-consuming by the advanced XDLVO theory. Moreover, the regression coefficient (R) of GABP reached 0.9999, and the error between the prediction results and the simulation results was less than 0.01%, indicating feasibility of the GABP ANN technique for quantification of interfacial interaction related with adhesive membrane fouling. This work provided a novel strategy to efficiently optimize the thermodynamic prediction of adhesive membrane fouling, beneficial for better understanding and control of adhesive membrane fouling.

Recent trends and challenges with the synthesis of membranes: Industrial opportunities towards environmental remediation

The industrial and agricultural revolution has posed a serious and potential threat to environment. The industrial and agricultural pollutants are directly released into the environment. This issue has clinched the scientists to work on different materials in order to decontaminate the environment. Among all other techniques, the membrane filtration technology has fascinated researchers to overcome the pollution by its promising features. This review elaborated various membrane synthesis approaches along with their mechanism of filtration, their applications towards environmental remediation such as removal of heavy metals, degradation of dyes, pharma waste, organic pollutants, as well as gas sensing applications. The membrane synthesis using different sort of materials in which inorganic, carbon materials, polymers and metal organic framework (MOFs) are highlighted. These materials have been involved in synthesis of membrane to make it more cost effective and productive to remove such hazardous materials from wastewater. Based on the reported literature, it has been found that inorganic and polymer membranes are facing issues of brittleness and swelling prior to the industrial scale applications related to the high temperature and pressure which needs to be addressed to enhance the permeation performance.

Cellulose Nanofibers Derived Surface Coating in Enhancing the Dye Removal with Cellulosic Ultrafiltration Membrane

Commercially available ultrafiltration membranes were coated with cellulose nanofibers (CNFs) produced from softwood pulp by a two-step process: a non-derivatizing DES treatment and a simple mechanical treatment (high-speed homogenization and sonification). The CNFs coating aimed at enhancement of the removal of methylene blue (MB) from water and was investigated at different concentrations of the coating, quantified in grams of CNFs per square meter of the membrane (1.3, 6.5, 13, and 19.5 g/m²). The pure water permeability (PWP) was unaffected up to the concentration of 6.5 g/m² but the dye retention increased approximately 2.5-fold. Even higher improvement of MB removal, about 4-fold, was observed when 19.5 g/m² were used, however, the pure water permeability also decreased by about 30%. In addition, it was proved that the coating can be removed and created again several times which shows that the concept could be used to improve the retention of organic compounds when high permeability membranes are used.

Recent Advances in the Removal of Organic Dyes from Aqueous Media with Conducting Polymers, Polyaniline and Polypyrrole, and Their Composites

Water pollution by organic dyes, and its remediation, is an important environmental issue associated with ever-increasing scientific interest. Conducting polymers have recently come to the forefront as advanced agents for removing dye. The present review reports on the progress represented by the literature published in 2020-2022 on the application of conducting polymers and their composites in the removal of dyes from aqueous media. Two composites, incorporating the most important polymers, polyaniline, and polypyrrole, have been used as efficient dye adsorbents or photocatalysts of dye decomposition. The recent application trends are outlined, and future uses also exploiting the electrical and electrochemical properties of conducting polymers are offered.

A critical review on classifications, characteristics, and applications of electrically conductive membranes for toxic pollutant removal from water: Comparison between composite and inorganic electrically conductive membranes

Research efforts have recently been directed at developing electrically conductive membranes (EMs) for pressure-driven membrane separation processes to remove effectively the highly toxic pollutants from water. EMs serve as both the filter and the electrode during filtration. With the assistance of a power supply, EMs can considerably improve the toxic pollutant removal efficiency and even realize chemical degradation to reduce their toxicity. Organic-inorganic composite EMs and inorganic EMs show remarkable differences in characteristics, removal mechanisms, and application situations. Understanding their differences is highly important to guide the future design of EMs for specific pollutant removal from water. However, reviews concerning the differences between composite and inorganic EMs are still lacking. In this review, we summarize the classifications, fabrication techniques, and characteristics of composite and inorganic EMs. We also elaborate on the removal mechanisms and performances of EMs toward recalcitrant organic pollutants and toxic inorganic ions in water. The comparison between composite and inorganic EMs is emphasized particularly in terms of the membrane characteristics (pore size, permeability, and electrical conductivity), application situations, and underlying removal mechanisms. Finally, the energy consumption and durability of EMs are evaluated, and future perspectives are presented.

Recent advances in electrocatalytic membrane for the removal of micropollutants from water and wastewater

The increasing occurrence of micropollutants in water and wastewater threatens human health and ecological security. Electrocatalytic membrane (EM), a new hybrid water treatment platform that integrates membrane separation with electrochemical technologies, has attracted extensive attention in the removal of micropollutants from water and wastewater in the past decade. Here, we systematically review the recent advances of EM for micropollutant removal from water and wastewater. The mechanisms of the EM for micropollutant removal are first introduced. Afterwards, the related membrane materials and operating conditions of the EM are summarized and analyzed. Lastly, the challenges and future prospects of the EM in research and applications are also discussed, aiming at a more efficient removal of micropollutants from water and wastewater.

Conductive polyethersulfone membrane facilely prepared by simultaneous phase inversion method for enhanced anti-fouling and separation under low driven-pressure

Electrically conductive membranes have been regarded as a new alternative to overcome the crucial drawbacks of membranes, including permeability-selectivity trade-off and fouling. It is still challenging to prepare conductive membranes with good mechanical strength, high conductivity and stable separation performance by reliable materials and methods. This work developed a facile method of simultaneous phase inversion to prepare electrically conductive polyethersulfone (PES) membranes with carboxylic multiwalled carbon nanotubes (MWCNT) and graphene (Gr). The resultant MWCNT/Gr/PES nanocomposite membranes are composed of the upper MWCNT/Gr layer with good conductivity and the base PES layer providing mechanical support. MWCNT as nanofillers effectively turns the insulting PES layers to be electrically conductive. With the dispersing and bridging functions of Gr, the MWCNT/Gr layer shows an enhanced electric conductivity of 0.10 S/cm. This MWCNT/Gr/PES membrane in an electro-filtration cell achieves excellent retention of Cu(II) ions up to 98 % and a high flux of 94.5 L m^-2∙h^-1∙bar^-1 under a low driven-pressure of 0.1 MPa. The conductive membrane also shows improved anti-fouling capability during protein filtration, due mainly to the electrostatic repulsion and hydrogen evolution reaction on the electrode. This facile strategy has excellent potential in electro-assistant membrane filtration for fouling control and effective separation.