Characterization of PAHs and metals in indoor/outdoor PM10/PM2.5/PM1 in a retirement home and a school dormitory

The relative contributions of traffic and non-traffic sources in ultrafine particle formations in Tehran mega city

Emissions of ultrafine particles (UFPs; diameter < 100 nm) are strongly associated with traffic-related emissions and are a growing global concern in urban environments. The aim of this study was to investigate the variations of particle number concentration (PNC) with a diameter > 10 nm at nine stations and understand the major sources of UFPs (primary vs. secondary) in Tehran megacity. The study was carried out in Tehran in 2020. NOx and PNC were reported from a total of nine urban site locations in Tehran and BC concentrations were examined at two monitoring stations. Data from all stations showed diurnal changes with peak morning and evening rush hours. The hourly PNC was correlated with NOx. PNCs in Tehran were higher compared to those of many cities reported in the literature. The highest concentrations were at District 19 station (traffic) and the lowest was at Punak station (residential) such that the average PNC varied from 8.4 × 103 to 5.7 × 104 cm-3. In Ray and Sharif stations, the average contributions of primary and secondary sources of PNC were 67 and 33%, respectively. Overall, we conclude that a decrease in primary emission leads to a decrease in the total concentration of aerosols, despite an increase in the formation of new particles by photo nucleation.

Effect of PM2.5 exposure on adhesion molecules and systemic nitric oxide in healthy adults: The role of metals, PAHs, and oxidative potential

Since there is limited evidence on the impact of PM2.5 content on cardiovascular biomarkers, we conducted a cross-sectional study on 89 healthy adults from October 12 to November 21, 2021. We measured daily PM2.5 in two distinct regions during different time windows: a high-traffic urban area and an industrial suburb. The concentrations of metals, PAHs, and oxidative potential (OP) were determined using ICP-MS, GC-MS, and dithiothreitol (DTT), respectively. Systemic biomarkers, including NO, sICAM-1, sVCAM-1, MDA, and CRP, were quantified in each subject simultaneously. A generalized linear model was used to examine the association between PM2.5 toxicity and each health endpoint. Our findings indicated that daily PM2.5 concentrations exceeded the WHO-recommended level by approximately sevenfold. We found that PM2.5 exposure was associated with adverse cardiovascular outcomes. Moreover, exposure to PM2.5 mass, total PAHs, and certain trace metals (Ni, Fe, V, As, and Pb) resulted in a decline in serum NO levels. At lag 3, exposure to PM2.5 mass resulted in a significant decrease in NO levels [1.32% (95% CI: -2.27, -0.12)] and total PAHs [2.05% (95% CI: -3.93, -0.12)]. In contrast, OP exhibited a mild correlation with NO level increases. Positive associations were observed between PM2.5 and its chemical constituents (PAHs, As, Cu, OP) and adhesion molecules at different lag times. An increase of 0.16 ppb in PAH concentrations at an interquartile range was associated with a 4.74% decline (95% CI, -7.80, -0.55) in the sVCAM-1 level. However, our study did not reveal any significant trend between pollutants and other biomarkers (sICAM-1, MDA, and CRP). Consequently, our findings suggest that different PM2.5 chemical compositions exhibit diverse behavior in biological responses.

Characterisation of polycyclic aromatic hydrocarbons associated with indoor PM0.1 and PM2.5 in Hanoi and implications for health risks

Polycyclic aromatic hydrocarbons (PAHs) associated with indoor PM pose a high risk to human health because of their toxicity. A total of 160 daily samples of indoor PM2.5 and PM0.1 were collected in Hanoi and analysed for 15 PAHs. In general, the concentrations of carcinogenic PAHs (car-PAHs) accounted for 21% ± 2%, 19.1% ± 2%, and 26% ± 3% of the concentrations of 15 PAHs in PM2.5, PM0.1-2.5, and PM0.1, respectively. Higher percentages of car-PAHs were found in smaller fractions (PM0.1), which can be easily deposited deep in the pulmonary regions of the human respiratory tract. The concentrations of 15 PAHs were higher in winter than in summer. The most abundant PAH species were naphthalene and phenanthrene, accounting for 11%-21% and 19%-23%, respectively. The PAH content in PM0.1 was almost twice as high as those in PM2.5 and PM0.1-2.5. Principal component analysis found that vehicle emissions and the combustion of biomass and coal were the main outdoor sources of PAHs, whereas indoor sources included cooking activities, the combustion of incense, scented candles, and domestic uses in houses. According to the results, 60%-90% of the PM0.1-bound BaP(eq) was deposited in the alveoli region, whereas 63%-75% of the PM2.5-bound BaP(eq) was deposited in head airways (HA), implying that most of the particles deposited in the HA region were PM0.1-2.5. The contributions of dibenz[a,h]anthracene and benzo[a]pyrene were dominant and contributed from 36% to 51% and 31%-50%, respectively, to the carcinogenic potential, whereas benzo[a]pyrene contributed from 30% to 49% to the mutagenic potential for both size fractions. The incremental lifetime cancer risk, simulated by Monte Carlo simulation, was within the limits set by the US EPA, indicating an acceptable risk for the occupants. These results provide an additional scientific basis for protecting human health from exposure to indoor PAHs.

Selenium and zinc alleviate quaternary metal mixture -induced neurotoxicity in rats by inhibiting oxidative damage and modulating the expressions of NF-kB and Nrf2/Hmox-1 pathway

Background

This study evaluated the potential protective effects of Zn and Se in the cerebellum and cerebral cortex, two fundamentally important brain regions, in albino rats that were exposed to heavy metals mixture (Al, Pb, Hg and Mn).

Methods

Animals were divided into five groups of seven animals per group with following patterns of exposure, controls group 1 were orally treated with deionized water for 60 days; group 2 was exposed to heavy metal mixture (HMM) with following concentrations (20 mg·kg^-1 of Pb body weight; 0.40 mg·kg^-1 of Hg; 0.56 mg·kg^-1 of Mn; and 35 mg·kg^-1; of Al), while groups 3,4 and 5 were exposed to HMM and orally co-treated with zinc chloride (ZnCl₂; 0.80 mg/kg), sodium selenite (Na₂SeO₃;1.50 mg/kg) and zinc chloride plus sodium selenite (ZnCl_0.2 + Na₂SeO₃) respectively.

Results

Exposure to HMM depressed cellular antioxidant apparatus, induced generation of lipid peroxidation markers (Malondialdehyde and NO), downregulated expression of transcription factors (Nrf2, and NF-kB) and upregulated Caspase 3 levels. HMM potentiated acetylcholinesterase activity and induced moderate histopathological alterations. Nevertheless, Zn, Se and in particular Zn + Se had recovering effects on all mentioned hazardous effects produced by HMM exposure in the cerebral cortex and cerebellum.

Conclusions

Selenium and zinc exert neuroprotection via Nrf2/NF-kB signaling pathways against quaternary heavy metal mixture-induced impairments in albino Sprague Dawley rats.

Exposure hazards of particles and volatile organic compounds emitted from material extrusion 3D printing: Consolidation of chamber study data

Ultrafine particles and volatile organic compounds (VOCs) have been detected from material extrusion 3D printing, which is widely used in non-industrial environments. This study consolidates data of 447 particle emission and 58 VOC emission evaluations from a chamber study using a standardized testing method with various 3D printing scenarios. The interquartile ranges of the observed emission rates were 109-1011 #/h for particles and 0.2-1.0 mg/h for total VOC. Print material contributed largely to the variations of particle and total VOC emissions and determined the most abundantly emitted VOCs. Printing conditions and filament specifications, included printer brand, print temperature and speed, build plate heating setup, filament brand, color and composite, also affected emissions and resulted in large variations observed in emission profiles. Multiple regression showed that particle emissions were more impacted by various print conditions than VOC emissions. According to indoor exposure modeling, personal and residential exposure scenarios were more likely to result in high exposure levels, often exceeding recommended exposure limits. Hazardous VOCs commonly emitted from 3D printing included aromatics, aldehydes, alcohols, ketones, esters and siloxanes, among which were various carcinogens, irritants and developmental and reproductive toxins. Therefore, 3D printing emits a complex mixture of ultrafine particles and various hazardous chemicals, exposure to which may exceed recommended exposure limits and potentially induce acute, chronic, or developmental health effects for users depending on exposure scenarios.

Investigating PM2.5 toxicity in highly polluted urban and industrial areas in the Middle East: human health risk assessment and spatial distribution

Exposure to particulate matter (PM) can be considered as a factor affecting human health. The aim of this study was to investigate the concentration of PM2.5 and heavy metals and their influence on survival of A549 human lung cells in exposure to PM2.5 breathing air of Ahvaz city. In order to assess the levels of PM2.5 and heavy metals, air samples were collected from 14 sampling stations positioned across Ahvaz city during both winter and summer seasons. The concentration of heavy metals was determined using ICP OES. Next, the MTT assay [3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide] was employed to ascertain the survival rate of A549 cells. The findings from this research demonstrated that average PM2.5 of the study period was (149.5 μg/m3). Also, the average concentration of PM2.5 in the urban area in winter and summer was (153.3- and 106.9 μg/m3) and in the industrial area this parameter was (191.6 and 158.3 μg/m3). The average concentration of metals (ng/m3) of urban areas against industrial, Al (493 vs. 485), Fe (536 vs. 612), Cu (198 vs. 212), Ni (128 vs. 129), Cr (48.5 vs. 54), Cd (118 vs. 124), Mn (120 vs. 119), As (51 vs. 67), Hg (37 vs. 50), Zn (302 vs. 332) and Pb (266 vs. 351) were obtained. The results of the MTT assay showed that the highest percentage of cell survival according to the exposure concentration was 25 > 50 > 100 > 200. Also, the lowest percentage of survival (58.8%) was observed in the winter season and in industrial areas with a concentration of 200 μg/ml. The carcinogenic risk assessment of heavy metals indicated that except for Cr, whose carcinogenicity was 1.32E-03, other metals were in the safe range (10-4-10-6) for human health. The high concentration of PM2.5 and heavy metals can increase respiratory and cardiovascular diseases and reduce the public health level of Ahvaz citizens.

Assessing Lifetime Cancer Risk Associated with Population Exposure to PM-Bound PAHs and Carcinogenic Metals in Three Mid-Latitude Metropolitan Cities

Lifetime cancer risk characterization of ambient PM-bound carcinogenic metals and polycyclic aromatic hydrocarbons (PAHs) were examined in the cities of Los Angeles (USA), Thessaloniki (Greece) and Milan (Italy), which share similar Mediterranean climates but are different in their urban emission sources and governing air quality regulations. The samples in Milan and Thessaloniki were mostly dominated by biomass burning activities whereas the particles collected in Los Angeles were primary impacted by traffic emissions. We analyzed the ambient PM2.5 mass concentration of Cadmium (Cd), Hexavalent Chromium (Cr(VI)), Nickel (Ni), Lead (Pb), as well as 13 PAH compounds in the PM samples, collected during both cold and warm periods at each location. Pb exhibited the highest annual average concentration in all three cities, followed by Ni, As, Cr(VI), Cd and PAHs, respectively. The cancer risk assessment based on outdoor pollutants was performed based on three different scenarios, with each scenario corresponding to a different level of infiltration of outdoor pollutants into the indoor environment. Thessaloniki exhibited a high risk associated with lifetime inhalation of As, Cr(VI), and PAHs, with values in the range of (0.97-1.57) × 10-6, (1.80-2.91) × 10-6, and (0.77-1.25) × 10-6, respectively. The highest cancer risk values were calculated in Milan, exceeding the US EPA standard by a considerable margin, where the lifetime risk values of exposure to As, Cr(VI), and PAHs were in the range of (1.29-2.08) × 10-6, (6.08-9.82) × 10-6, and (1.10-1.77) × 10-6, respectively. In contrast, the estimated risks associated with PAHs and metals, except Cr(VI), in Los Angeles were extremely lower than the guideline value, even when the infiltration factor was assumed to be at peak. The lifetime cancer risk values associated with As, Cd, Ni, Pb, and PAHs in Los Angeles were in the range of (0.04-0.33) × 10-6. This observation highlights the impact of local air quality measures in improving the air quality and lowering the cancer risks in Los Angeles compared to the other two cities.

Characterization, risk assessment, and source estimation of PM10-bound polycyclic aromatic hydrocarbons during wintertime in the ambient air of Basrah City, Iraq

In this study, the concentration and structure of polycyclic aromatic hydrocarbons (PAHs) associated with the ambient PM₁₀ in Basrah City, Iraq have been investigated for the first time. From December 2021 to February 2022, PM₁₀ samples were collected on quartz fiber filters, extracted using an optimized extraction protocol, and analyzed for the sixteen US EPA priority PAHs. The results indicated that 4- and 5-ring PAHs represent 52% of the total detected PAHs. The most abundant PAHs over the study period were chrysene (1.2 ± 1.5 ng m^-3), fluorene (0.9 ± 1.4 ng m^-3), and benzo[b]fluoranthene (0.7 ± 0.9 ng m^-3). Source identification suggested that PM₁₀-bound PAHs primarily originated from pyrogenic and petrogenic activities in Basrah City. In addition, the cancer risk associated to PAH exposure was assessed based on benzo[a]pyrene equivalent concentration and was found ranging from 0.07 to 6.32 ng m^-3; hence, it exceeded the threshold limit of 1.0 ng m^-3 established by the European legislation (EU, 2014). Benzo[a]pyrene was determined to be main contributor to total carcinogenic power of the detected PAHs, accounting for 50.3%, followed by dibenz[a,h]anthracene (22.3%). Similarly, benzo[a]pyrene represented a major contributor to PAH associated mutagenicity, accounting for 43.5% of the total.

PAHs pollution in the outdoor air of areas with various land uses in the industrial city of Iran: distribution, source apportionment, and risk assessment

Shahryar city regions with various land uses had their outdoor air concentrations of PM_2.5-bound PAHs determined. Totally, 32 samples were taken - eight samples from the industrial region air (IS), eight samples from the high-traffic urban regions air (HTS), eight samples from the air of commercial regions (CS), and eight samples from residential areas (RS), which were analyzed by GC-MS. According to the study's findings, in the outdoor air of IS, HTS, CS, and RS, there were mean ƩPAHs concentrations of 23.25 ± 20.22, 38.88 ± 26.53, 6.97 ± 4.26, and 4.48 ± 3.13 ng/m³, respectively. As comparison to CS and RS, mean concentration of ƩPAHs in samples from HTS and IS was substantially greater (p < 0.05). Using the Unmix.6 receptor model, sources of PAHs in the air of Shahryar were allocated. The model's results show that 42% of PAHs come from diesel vehicles and industrial activities, 36% from traffic and other transportation sources, and 22% from heating sources and coal burning. The carcinogenicity suffering resulting from exposure to PAHs was as follows: This value for children of the ingestion, inhalation pathways and dermal contact is (1.90 × 10^-6-1.38 × 10^-4), (5.5 × 10^-11-2.67 × 10^-9) and (2.36 × 10^-6-1.72 × 10^-4), respectively. Also, for adults were (1.47 × 10^-6 - 1.07 × 10^-4), (1.14 × 10^-10 - 5.27 × 10^-9) and (3.68 × 10^-6- 2.87 × 10^-4), respectively. In general, the analyzed region's carcinogenicity risk estimates fell within the range of acceptable limit.

Cell Death Pathways: The Variable Mechanisms Underlying Fine Particulate Matter-Induced Cytotoxicity

Recently, the advent of health risks due to the cytotoxicity of fine particulate matter (FPM) is concerning. Numerous studies have reported abundant data elucidating the FPM-induced cell death pathways. However, several challenges and knowledge gaps are still confronted nowadays. On one hand, the undefined components of FPM (such as heavy metals, polycyclic aromatic hydrocarbons, and pathogens) are all responsible for detrimental effects, thus rendering it difficult to delineate the specific roles of these copollutants. On the other hand, owing to the crosstalk and interplay among different cell death signaling pathways, precisely determining the threats and risks posed by FPM is difficult. Herein, we recapitulate the current knowledge gaps present in the recent studies regarding FPM-induced cell death, and propose future research directions for policy-making to prevent FPM-induced diseases and improve knowledge concerning the adverse outcome pathways and public health risks of FPM.

Do cats mirror their owner? Paired exposure assessment using silicone bands to measure residential PAH exposure

It has been suggested that domestic animals can serve as sentinels for human exposures. In this study our objectives were to demonstrate that i) silicone collars can be used to measure environmental exposures of (domestic) animals, and that ii) domestic animals can be used as sentinels for human residential exposure. For this, we simultaneously measured polycyclic aromatic hydrocarbons (PAHs) using silicone bands worn by 30 pet cats (collar) and their owner (wristband). Collars and wristbands were worn for 7 days and analyzed via targeted Gas Chromatography-Mass Spectrometry (GC-MS). Demographics and daily routines were collected for humans and cats. Out of 16 PAHs, 9 were frequently detected (>50% of samples) in both wristbands and collars, of which Phenanthrene and Fluorene were detected in all samples. Concentrations of wristbands and collars were moderately correlated for these 9 PAHs (Median Spearman's r = 0.51 (range 0.16-0.68)). Determinants of PAH concentrations of cats and humans showed considerable overlap, with vacuum cleaning resulting in higher exposures and frequent changing of bed sheets in lower exposures. This study adds proof-of-principle data for the use of silicone collars to measure (domestic) animal exposure and shows that cats can be used as sentinels for human residential exposure.

Trace elements in outdoor and indoor PM2.5 in urban schools in Xi'an, Western China: characteristics, sources identification and health risk assessment

The PM_2.5-bounded elements were measured in outdoor and indoor from two urban middle schools in Xi'an. The PM_2.5 mass was from 42.4 to 283.7 µg/m³ with bounded element from 3.4 to 41.7 µg/m³. Both the particle mass and the bounded elements displayed higher levels compared with previous studies in school environments. The most abundant elements were Ca, K, Fe, S, Zn and Cl both indoor and outdoor in two schools, which accounted for about 90% of the total elements. Strong correlations between indoor and outdoor were obtained along with relative effect from students' and teachers' activities on the indoor distributions between workdays and weekends. There had different indoor/outdoor (I/O) distributions for the two schools. It revealed the main outdoor sources for elements in JT and predominance of indoor sources in HT. The principal component analysis investigated main sources of elements in this study were coal combustion, geogenic dust and industrial emission, even though there displayed differences in the two school classrooms. The health risk assessment showed that the cancer risk for Ni and Pb was below the safe value while As and Cr might pose acceptable potential threat to both students' and teachers' health. The total non-cancer risks of accumulative multi-metals in JT exhibited to be higher than 1, indicating that there existed the potential non-carcinogenic health risks of exposure metals.

Metal compositions of particle emissions from material extrusion 3D printing: Emission sources and indoor exposure modeling

Material extrusion 3D printing has been widely used in industrial, educational and residential environments, while its exposure health impacts have not been well understood. High levels of ultrafine particles are found being emitted from 3D printing and could pose a hazard when inhaled. However, metals that potentially transfer from filament additives to emitted particles could also add to the exposure hazard, which have not been well characterized for their emissions. This study analyzed metal (and metalloid) compositions of raw filaments and in the emitted particles during printing; studied filaments included pure polymer filaments with metal additives and composite filaments with and without metal powder. Our chamber study found that crustal metals tended to have higher partitioning factors from filaments to emitted particles; silicon was the most abundant element in emitted particles and had the highest yield per filament mass. However, bronze and stainless-steel powder added in composite filaments were less likely to transfer from filament to particle. For some cases, boron, arsenic, manganese, and lead were only detected in particles, which indicated external sources, such as the printers themselves. Heavy metals with health concerns were also detected in emitted particles, while their estimated exposure concentrations in indoor air were below air quality standards and occupational regulations. However, total particle exposure concentrations estimated for indoor environments could exceed ambient air fine particulate standards.

Impact of polycyclic aromatic hydrocarbon exposure on cognitive function and neurodegeneration in humans: A systematic review and meta-analysis

Introduction

This article documents an emerging body of evidence concerning the neurological effect of polycyclic aromatic hydrocarbon (PAH) exposure with regard to cognitive function and increased risk of neurodegeneration.

Methods

Two electronic databases, PubMed and Web of Science, were systematically searched.

Results

The 37/428 studies selected included outcomes measuring cognitive function, neurobehavioral symptoms of impaired cognition, and pathologies associated with neurodegeneration from pre-natal (21/37 studies), childhood (14/37 studies), and adult (8/37 studies) PAH exposure. Sufficient evidence was found surrounding pre-natal exposure negatively impacting child intelligence, mental development, average overall development, verbal IQ, and memory; externalizing, internalizing, anxious, and depressed behaviors; and behavioral development and child attentiveness. Evidence concerning exposure during childhood and as an adult was scarce and highly heterogeneous; however, the presence of neurodegenerative biomarkers and increased concentrations of cryptic "self" antigens in serum and cerebrospinal fluid samples suggest a higher risk of neurodegenerative disease. Associations with lowered cognitive ability and impaired attentiveness were found in children and memory disturbances, specifically auditory memory, verbal learning, and general memory in adults.

Discussion

Although evidence is not yet conclusive and further research is needed, the studies included supported the hypothesis that PAH exposure negatively impacts cognitive function and increases the risk of neurodegeneration in humans, and recommends considering the introduction of a variable "rural vs. urban" as covariate for adjusting analyses, where the neurological functions affected (as result of our review) are outcome variables.

Spatial distribution, driving factors and health risks of fine particle-bound polycyclic aromatic hydrocarbons (PAHs) from indoors and outdoors in Hefei, China

Atmospheric particulate matter, especially in urban and industrial environments, can act as a source of different organic pollutants that can pose significant health impacts to residents. However, the pollution status and transport mechanisms of fine particle-bound polycyclic aromatic hydrocarbons (PAHs) in indoor and outdoor environments are uncertain. This study aimed to determine the spatial distribution and morphological characteristics of fine particle-bound PAHs and analyze the factors (source contributions and backward trajectories) that influence their concentrations. The results showed that mean concentrations of 16 PAHs were higher in indoor dust as compared to outdoor dust. In addition, the lowest concentrations of the 16 PAHs were found on the 11-20th floor, with smoking households > nonsmoking households (except Nap, Acy, and Ace). The 2-3 ring PAHs were more prominent in households with cooking activities. The particle size distribution showed that most of the particles were <62 μm in diameter, indicating that the indoor particles were smaller in size. Furthermore, the range of δ13C values in the outdoor dust (-30.17 ~ -28.63 ‰) samples was significantly lower than in indoor dust (-28.29 ~ -22.53 ‰). The results based on diagnostic ratios, positive matrix factorization (PMF) analysis and backward trajectory model analysis suggested that the sources of PAHs in indoor and outdoor dust were mixed, originated both locally and from neighboring provinces transported over long distances, especially concentrated in the Yangtze River Delta area. Finally, carcinogenic risk values for indoor dust were greater than those for outdoor dust. Therefore, it is recommended that local governments and industries with high PAH emissions should implement proper protocols to monitor and minimize the pollution levels of PAHs in the urban industrial environment in order to mitigate their health risks.

Seasonal changes and respiratory deposition flux of PM2.5 and PM10 bound metals in Dhaka, Bangladesh

Due to rapid urbanization and fast economic development, aerosol pollution is a serious environmental issue, especially in Bangladesh. Based on bioaccessibility and respiratory deposition doses (RDD), health risks of PM_2.5 and PM₁₀ bound 15 (fifteen) metals were investigated at fourteen urban sites (roadside, marketplace, industrial, and commercial areas). Sampling campaigns were conducted over four seasons (winter, summer, rainy, and autumn) from December 2020 to November 2021. A beta attenuation mass analyzer measured particulate matter concentrations in ambient air. The metals in PM fractions were analyzed by X-ray fluorescence spectroscopy and inductively coupled plasma mass spectrometry (ICP-MS). The airborne trace metals (Cd, As, Zn, Pb, Cr, Cu, Ni) with high enrichment factors indicate anthropogenic sources. The positive matrix factorization (PMF) categorized these elements as originating from automobile exhaust, industrial emissions, and solid waste/coal combustion, whereas the geologic elements came from earth crust/soil dust. During the winter, most of the air mass trajectories arrived from India across the land (82%) and Indo Gangetic Plain (IGP) region to the sampling sites, which may have aided in the transport of pollutants. The deposition flux of metals illustrated that compared to PM_2.5, PM₁₀ deposited a higher amount of metals in the upper airways (81.96%). In comparison, PM_2.5 accumulates more elevated amounts of metals in alveolar regions (11.77%), due to the ability of fine particles to penetrate deeper into the lower pulmonary region. Among age groups, an adult inhales a higher amount of metals than a child, on average 0.103 mg and 0.08 mg of metals per day via PM_2.5, respectively. Acute health impacts are caused by the deposited cancer-causing metals in alveolar tissue, which circulates through the bloodstream and affects several organs. Prolonged exposure to these carcinogenic metals poses significant health risks.

Meteorological dependence, source identification, and carcinogenic risk assessment of PM2.5-bound Polycyclic Aromatic Hydrocarbons (PAHs) in high-traffic roadside, urban background, and remote suburban area

The Polycyclic Aromatic Hydrocarbons (PAHs) bound to ambient fine Particular Matter (PM2.5) are currently drawing a lot of attention due to their adverse health effects increasing lung cancer risk in humans. In this study, The PM2.5 samples were collected by high volume air samplers simultaneously from three different sites (high-traffic roadside, urban background, and remote suburban) in Tehran, Iran during warm and cold seasons (from July 2018 to March 2019), and 16 PAHs were analyzed using Gas Chromatography-Mass Spectrometry (GC-MS). Unlike previous studies, a remote suburban area was chosen so as to observe the spatial differentiation in PM2.5-bound PAH characteristics. In high-traffic roadside site, the average concentration of total PM2.5-bound PAHs (ƩPAHs) was 3.7 times the concentration value in remote suburban area. Average (ƩPAHs) ranged from 5.54 ng/m3 for remote suburban area to 20.67 ng/m3 for high-traffic roadside site. In all sites, seasonal trends of PAH concentrations elucidated high concentrations in the cold season and low concentrations in the warm season. Correlation analysis between ƩPAHs and atmospheric factors (meteorology parameters and criteria air pollutants) indicated the heterogeneous processes play an important role in the level of PAHs. The results of diagnostic ratio (DR) analysis disclosed that the dominant source of PM2.5-bound PAHs was the combustion of liquid fossil fuels. Despite the fact that incremental lifetime cancer risk (ILCR) via inhaling PM2.5-bound PAHs varied significantly in high-traffic roadside site and remote suburban site, its value was beyond the acceptable risk level in both sites. Our results suggested that effective regulations are needed to monitor PAHs concentrations and reduce PAHs emissions from liquid fossil fuel combustion so as to mitigate the potential carcinogenic risk of PAHs in ambient air.

Supplementary Information

The online version contains supplementary material available at 10.1007/s40201-022-00821-2.

Increased allergic and asthmatic risks in children residing in industrial areas by surveying the pre-inflammatory (IgE, IL-4 and IL-13) biomarkers

Toxic metal(loid)s can lead to high damages on human. This work was conducted to investigate the levels of metal(loid)s in PM2.5 and a total of 123 male children's (aged 6-9 years) blood chosen from different areas in Ahvaz and their association with the pre-inflammatory (Immunoglobulin E and cytokines: IgE, IL-4 and IL-13) responses in serum cells. Six metal(loid)s (arsenic, cadmium, chromium, mercury, nickel and lead) in three regions including industrial (Padad), vehicle traffic (Golestan) and reference (Kianpars) areas were studied. Results showed the concentrations of As, Cr, Cd, Ni and Hg in the ambient air of industrial area (Padad) (P < 0.001), and Pb in vehicle traffic area (Golestan) were higher (p < 0.001). Moreover, the mean levels of IgE (mean = 146.44 pg/200landa, P < 0.003), IL-4 (mean = 548.23 pg/200landa, P < 0.001) and IL-13 (mean = 53.21 pg/200landa, P < 0.001) in Padad were higher than Golestan and Kianpars. Our results suggest that living in industrial areas leads to accelerated synthesis of IgE, IL-4 and IL-13 in blood. The spatial distribution of children's serum IgE, IL-4 and IL-13 concentrations showed an abnormal increase of 240 to 400 pg/200landa for IgE, 950 to 1400 pg/200landa for IL-4 and 90 to 128 pg/200landa for IL-13. Our results indicate children in the industrial area are prone to asthma, allergy, miRNA mutation, and other chronic diseases.

Ambient concentrations and dosimetry of inhaled size-segregated particulate matter during periods of low urban mobility in Bragança, Portugal

The restrictive measures in place during the COVID-19 pandemic provided a timely scenario to investigate the effects of human activities on air quality, and the extent to which mobility reduction strategies can impact atmospheric pollutant levels. Real-time concentrations of PM₁, PM_2.5 and PM₁₀ were measured using a mobile platform in a small city of Portugal, during morning and afternoon rush hours, in two distinct phases of the pandemic: emergency phase (cold period, lockdown) and calamity phase (warm period, less restricted). The Multiple-Path Particle Dosimetry Model (MPPD) was used to calculate the PM deposition for adults. Large spatio-temporal variabilities and pronounced changes in mean PM concentrations were observed, with lower concentrations in the calamity phase: PM₁ = 2.33 ± 1.61 μg m^-3; PM_2.5 = 5.15 ± 2.77 μg m^-3; PM₁₀ = 23.30 ± 21.53 μg m^-3 than in the emergency phase: PM₁ = 16.85 ± 31.80 μg m^-3; PM_2.5 = 30.92 ± 31.93 μg m^-3; PM₁₀ = 111.27 ± 104.53 μg m^-3. These changes are explained by a combination of meteorological factors and local emissions, mainly residential firewood burning. Regarding regional deposition, PM₁ was the main contributor to deposition in the tracheobronchial (5%) and pulmonary (12%) regions, and PM₁₀ in the head region (92%). In general, total deposition doses were higher for males than for females. This work quantitatively demonstrated that even with a 38% reduction in urban mobility during the lockdown, the use of firewood for residential heating is the main contributor to the high concentrations of PM and the respective inhaled dose.

Molecular signatures of organic particulates as tracers of emission sources

Chemical signature of airborne particulates and deposition dusts is subject of study since decades. Usually, three complementary composition markers are investigated, namely, (i) specific organic compounds; (ii) concentration ratios between congeners, and (iii) percent distributions of homologs. Due to its intrinsic limits (e.g., variability depending on decomposition and gas/particle equilibrium), the identification of pollution sources based on molecular signatures results overall restricted to qualitative purposes. Nevertheless, chemical fingerprints allow drawing preliminary information, suitable for successfully approaching multivariate analysis and valuing the relative importance of sources. Here, the state-of-the-art is presented about the molecular fingerprints of non-polar aliphatic, polyaromatic (PAHs, nitro-PAHs), and polar (fatty acids, organic halides, polysaccharides) compounds in emissions. Special concern was addressed to alkenes and alkanes with carbon numbers ranging from 12 to 23 and ≥ 24, which displayed distinct relative abundances in petrol-derived spills and exhausts, emissions from microorganisms, high vegetation, and sediments. Long-chain alkanes associated with tobacco smoke were characterized by a peculiar iso/anteiso/normal homolog fingerprint and by n-hentriacontane percentages higher than elsewhere. Several concentration ratios of PAHs were identified as diagnostic of the type of emission, and the sources of uncertainty were elucidated. Despite extensive investigations conducted so far, the origin of uncommon molecular fingerprints, e.g., alkane/alkene relationships in deposition dusts and airborne particles, remains quite unclear. Polar organics resulted scarcely investigated for pollution apportioning purposes, though they looked as indicative of the nature of sources. Finally, the role of humans and living organisms as actual emitters of chemicals seems to need concern in the future.

Characteristics of particle-bound polycyclic aromatic hydrocarbons (PAHs) in indoor PM2.5 of households in the Southwest part of Ulaanbaatar capital, Mongolia

Air pollution, including PM_2.5 concentration in Ulaanbaatar (capital of Mongolia) is a serious matter of concern. As the majority of households use coal in large areas of the city, indoor air quality is also posing a serious risk to human health. This study investigated the concentration of polycyclic aromatic compounds (PAHs) in indoor particulate matter (PM_2.5) in 10 non-smoker households. Sampling was conducted in winter of 2018, between 27 January and 09 February. Concentrations of PM_2.5 in the indoor air of households ranged between 62.8 and 324.8 µg m^-3. Total concentration of PAHs also varied in a relatively wide range, between 46.2 and 175.7 ng m^-3. Five-ring PAHs represented a considerably high fraction of total PAHs between 25 and 53%, benzo[b]fluoranthene (BbF) and benzo[a]pyrene (BaP) were the two predominant compounds within five-ring PAHs. Significant correlation was found between indoor and outdoor particulate matter levels in wintertime. Considering individual characteristic PAHs, heavier PAHs homologues (4- to 5-ring and 6-ring PAHs) were detected in all households, which suggested the influence of coal combustion and traffic exhaust. Health risk of children attributed to PAHs inhalation was assessed by taking into account the lifetime-average daily dose (LADD) and corresponding lifetime cancer risk. Lifetime average daily dose for children in only one household were slightly higher than health-based guideline level (1.0 × 10^-5), defined by WHO, whereas LADD for adults and children of other households were within acceptable limit. The cancer risks from the exposure of children to air pollutants in all households except HH-3 were found high. In the Vibrio fischeri bioluminescence inhibition assay, according to the toxic unit (TU) values of indoor PM_2.5 from ten households, all samples were classified as toxic.

Health Risk Assessment on Exposure to PM2.5-bound PAHs from an Urban-industrial Area in Rayong City, Thailand

BACKGROUND: A city's industrial area's air quality has become a major priority. PM2.5-bound polycyclic aromatic hydrocarbons (PAHs) are one of the most common pollutants in urban-industrial area, and can be linked to health problems. AIM: This study aims to 1) investigate PM2.5 and PAHs emitted from roadside area (RS) and industrial estate (IE) in Rayong city 2) assess the inhalation of PM2.5 and PAHs on the human health of the age group. METHODS: PM2.5-bound PAHs were investigated and thier carcinogenic risk was evalued in this study. PM2.5 samples were collected on quartz filters contained in a mini-volume air sampler and analyzed for PAHs by GC-MS. RESULTS: The average PM2.5 concentrations at RS and IE were 43.3±26.8 and 40.4±21.7 µg/m3, while the values of total PAHs in both sites were 1.68±1.53 and 1.34±1.22 ng/m3, respectively. However, it was found that the PM2.5 and PAHs values were not significantly different (p>0.05). The results revealed that the individual lifetime cancer risk (Ric) of PM2.5 values for children and adults at both sites indicated acceptable cancer risk (10-6 to10-4). According to the incremental lifetime cancer risk (ILCR) values of PAHs for different age groups, exposure to PAHs in PM2.5 through the inhalation pathway was a negligible (<10-6). CONCLUSION: As a result, the PM2.5 concentrations have substantial implications for Rayong city’s environmental management and protection, relating to car emissions and coal combustion.

Effect of portable air purifier on indoor air quality: reduced exposure to particulate matter and health risk assessment

We sought to investigate the impact of air purifiers in the removal of particular matter (PM)₁₀, PM_2.5, PM_1, and particle number concentration (PNC) in the indoor air of dormitories located at Iran's largest medical university, Tehran University of Medical Sciences. Twelve rooms were selected and randomly assigned to two rooms: sham air purifier system deployed room (SR) and true air purifier system deployed room (TR). All study samples were drawn simultaneously from assigned rooms using portable GRIMM dust monitors for 24 h. The PM monitors of air were positioned in the middle of each room next to the air purifier at the height of the breathing zone (1.5 m in height). The mean PM₁₀, PM_2.5, PM₁, and PNC removal efficiency in rooms with and without a smoker were measured to be 40.7 vs 83.8%, 31.2 vs 78.4%, 29.9 vs 72.3%, and 44.3 vs 75.6%, respectively. The results showed that smoking is an important influencing factor on the indoor air quality; smoking lowered the removal efficiency of PM₁₀, PM_2.5, PM₁, and PNC by 43%, 47%, 43%, and 31%, respectively. An air purifier could decline the PM₁₀ and PM_2.5 even lower than the WHO 24-h guideline level in non-smoker rooms. This study revealed that using household air purifiers in rooms with smokers and non-smokers significantly reduces the non-carcinogenic risks of exposure to PM₁₀ and PM_2.5.

Health risks of PM2.5-bound polycyclic aromatic hydrocarbon (PAH) and heavy metals (PPAH&HM) during the replacement of central heating with urban natural gas in Tianjin, China

To investigate the health effects of fine particulate matter (≤ 2.5 μm in aerodynamic diameter; PM_2.5)-bound heavy metals and polycyclic aromatic hydrocarbons (PAHs) before and after the implementation of the Urban Natural Gas Heating Project (UNGHP), the lifetime cancer risks, hazard quotients (HQs) of heavy metals and PAHs were calculated. Seven kinds of heavy metals (Al, As, Cd, Cr, Mn, Ni and Se) and 12 kinds of PAHs including acenaphthylene (ANY), acenaphthene (ANA), fluoranthene (FLT), pyrene (PYR), chrysene (CHR), benz[a]anthracene (BaA), benzo[b]fluoranthene (BbF), benzo[k]fluoranthene (BkF), benzo[a]pyrene (BaP), dibenz[a,h]anthracene (DBA), benzo[ghi]perylene (BPE) and indeno[1,2,3-cd]pyrene (IPY) were analyzed and used for the health risk assessments. It was found that HQ of Mn fell from 1.09 in the coal-burning period to 0.72 in the gas-burning period in the suburban area. And lifetime cancer risks of PAHs fell from 35.7 × 10^-6 in the coal-burning period to 17.22 × 10^-6 in the gas-burning period in the urban area. It could be concluded that, during the gas-burning period, downward trends were observed for the lifetime cancer risks and HQs of most kinds of heavy metals and PAHs in all regions of Tianjin compared to those during the coal-burning period. The UNGHP was effective, and we should also take other measures to control the pollution.

Indoor Air Quality in Elderly Centers: Pollutants Emission and Health Effects

The world population is ageing, in particular in the developed world, with a significant increase in the percentage of people above 60 years old. They represent a segment of the population that is more vulnerable to adverse environmental conditions. Among them, indoor air quality is one of the most relevant, as elders spend comparatively more time indoors than younger generations. Furthermore, the recent COVID-19 pandemic contributed immensely to raising awareness of the importance of breathing air quality for human health and of the fact that indoor air is a vector for airborne infections and poisoning. Hence, this work reviews the state of the art regarding indoor air quality in elderly centers, considering the type of pollutants involved, their emission sources, and their health effects. Moreover, the influence of ventilation on air quality is also addressed. Notwithstanding the potential health problems with the corresponding costs and morbidity effects, only a few studies have considered explicitly indoor air quality and its impacts on elderly health. More studies are, therefore, necessary to objectively identify what are the impacts on the health of elderly people due to the quality of indoor air and how it can be improved, either by reducing the pollutants emission sources or by more adequate ventilation and thermal comfort strategies.

The Use of the Novel Optical Method SEZO AM (WiRan Ltd.) for Measurements of Particulate Matter (PM10–2.5) in Port Areas-Case Study for Port of Gdynia (Poland)

From 1 March to 30 April and from 1 August to 30 September 2021, comparative studies of PM2.5 and PM10 concentrations were carried out in Gdynia. For intercalibration, a device was used that operates based on non-reference methodologies and without proven equivalence to the reference methodology (SEZO AM, WIRAN), and an EDM 180 analyzer (GRIMM) with certificates and approvals (US-EPA, UK-MCERTS, CN-CMA) was used. The aim of this research is to determine whether the SEZO AM device could be used in port areas for continuous PM2.5 and PM10 concentrations measurements. Two campaigns of two months allowed us to see a good agreement of the results achieved with both methods. The concordance of the results obtained from the SEZO AM and the EDM 180 methods amounted to between 78% and 94% for the PM2.5 and between 70% and 75% for the PM10. The comparison of two SEZO AM devices to a higher-class TSI OPS3330 reference in a measurement dust chamber showed a fit between 79% and 86% for the PM2.5 and between 81% and 86% for the PM10. This indicates the possibility of using this analyzer to measure the concentrations of PM2.5 and PM10 in the port atmosphere in which they were carried out. The preliminary analysis of meteorological parameters shows that the main potential impact on the concentration of the analyzed dust fractions measured by the SEZO AM method was relative humidity. The determination of the correction factor for the PM2.5 and PM10 concentrations and adding an inlet external cover contributed to a two-fold reduction in the analysis error and good concordance of the results, at a level of 93% for PM2.5 and 91% for PM10, without discarding any data.

Temporal profiles, source analysis, and health risk assessments of parent polycyclic aromatic hydrocarbons (PPAHs) and their derivatives (NPAHs, OPAHs, ClPAHs, and BrPAHs) in PM2.5 and PM1.0 from the eastern coastal region of China: Urban coastal area versus coastal background area

The eastern coastal region of China is the area with the highest emission of PAHs in China. Therefore, understanding the sources and health risk of parent polycyclic aromatic hydrocarbons (PPAHs) and their derivatives in eastern coastal cities of China is the main basis for air pollution control. In this study, we measured the concentrations of 18 parent PAHs, 17 nitrated PAHs, 7 oxygenated PAHs, 8 chlorinated PAHs, and 13 brominated PAHs in PM_1.0 and PM_2.5 samples collected at an urban coastal city site and a coastal background site in 2019. We analyzed the temporal distribution, molecular composition, and sources and performed health risk assessments for both winter and summer samples. The average concentration of the PPAHs and their derivatives (all 63 compounds combined) in the PM_1.0 samples accounted for 75.57% of the PAHs concentration in PM_2.5 samples. The average concentration of PM_2.5- and PM_1.0- bound PPAHs in winter was 114.70 times higher than in summer, and their derivatives was 27.51 times. Both the combined concentrations of the 18 PPAHs and the combined concentrations of the 45 derivatives were higher in the coastal city compared to the background site during the winter (1.90 and 1.48 times, respectively), but they were comparable during the summer. The positive matrix factorization analysis indicated that the compounds mainly originated from coal/biomass combustion, industrial sources, vehicle emissions, and secondary formation. In addition, the concentration-weighted trajectories model revealed that the PAHs were mainly emitted locally in Shandong Province and surrounding areas, such as Hebei Province, Henan Province, and Bohai Sea. The compounds 1-NPYR, 2+9-BrPHE, 9,10-Cl2PHE, and 1-ClPYR dominantly contributed to the derivatives of TEQ during the winter due to their high concentrations or the high TEFs of these compounds.

Seasonal trend and source identification of polycyclic aromatic hydrocarbons associated with fine particulate matters (PM2.5) in Isfahan City, Iran, using diagnostic ratio and PMF model

Particulate matters (PMs) and their associated chemical compounds such as polycyclic aromatic hydrocarbons (PAHs) are important factors to evaluate air pollution and its health impacts particularly in developing countries. Source identification of these compounds can be used for air quality management. The aim of this study was to identify the sources of PM_2.5-bound PAHs in Isfahan city, a metropolitan and industrialized area in central Iran. The PM_2.5 samples were collected at 50 sites during 1 year. Source identification and apportionment of particle-bound PAHs were carried out using diagnostic ratios (DRs) of PAHs and positive matrix factorization (PMF) model. The results showed that the concentrations of PM_2.5 ranged from 8 to 291 μg/m³ with an average of 60.2 ± 53.9 μg/m³, whereas the sum of concentrations of the 19 PAH compounds (ƩPAHs) ranged from 0.3 to 61.4 ng/m³ with an average of 4.65 ± 8.54 ng/m³. The PAH compounds showed their highest and lowest concentrations occurred in cold and warm seasons, respectively. The mean concentration of benzo[a]pyrene (1.357 ng m^-3) in December-January, when inversion occured, was higher than the Iranian national standard value showing the risk of exposure to PM_2.5-bound PAHs. Applying DRs suggested that the sources of the PAHs were mainly from fuel combustion. The main sources identified by the PMF model were gasoline combustion (23.8 to 33.1%) followed by diesel combustion (20.6 to 24.8%), natural gas combustion (9.5 to 28.4%), evaporative-uncombusted (9.5 to 23.0%), industrial activities (8.4 to 13.5%), and unknown sources (2.8 to 15.7%). It is concluded that transportation, industrial activities, and combustion of natural gas (both in residential-commercial and industrial sectors) as the main sources of PAHs in PM_2.5 should be managed in the metropolitan area, particularly in cold seasons.

Characterization and sources of trace elements in PM1 during autumn and winter in Qingdao, Northern China

Atmospheric sub-micrometer particles (PM₁, particles with an aerodynamic diameter ≤ 1.0 μm) monitoring in Qingdao, a coastal city in Northern China, was conducted for two consecutive years from November 1, 2018 to January 31, 2019 (hereafter referred to as OP_2018-2019) and from October 28, 2019 to January 20, 2020 (hereafter referred to as OP_2019-2020). The results showed that compared with OP_2018-2019, the concentrations of V, Ni, As, Pb, and Cd in PM₁ in OP_2019-2020 decreased by 61.9%, 31.4%, 49.2%, 25.4%, and 27.1%, respectively. For the indicators of ship emission sources, a significant reduction in V (73.3%) and Ni (22.1%) concentrations were observed after the implementation of the updated Domestic Emission Control Area (DECA 2.0) policy for ships since January 1, 2019 proposed by the Ministry of Transportation. This result demonstrated that the implementation of the DECA 2.0 policy had a significant effect on reducing ship emissions. The Field Emission Scanning Electron Microscope analysis identified the impact of ship emission sources, while the inconsistent distribution of V and Ni revealed other potential sources of Ni. The V/Ni ratios during the pre-policy and post-policy periods decreased by 40.7%. Along with the further implementation of the domestic coastal ship pollution control zone policy, V/Ni ratio should be cautiously used as a parameter for ship emission sources. The positive matrix factorization method identified five source factors: coal combustion/biomass burning (47.8%), crustal sources (21.2%), vehicle exhaust/road dust (15.1%), industrial emissions (11.1%), and ship emissions (4.9%). The contribution rates of ship emission sources before and after the DECA 2.0 policy were analyzed and found to be 5.6% and 3.4%. The potential source contribution factor analysis of As showed that the potential emission source areas were significantly reduced in OP_2019-2020, which might be related to the coal fired cleanup operations conducted in Beijing-Tianjin-Hebei and surrounding areas.

Source analysis of heavy metals in atmospheric particulate matter in a mining city

The enrichment of heavy metals in air-borne particulate matters poses a great threat to health. In order to understand the mineralogical characteristics and sources of heavy metals in atmospheric particulate matter in coal mining cities, PM_2.5 (particulate matter with an aerodynamic diameter less than 2.5 μm), PM₁₀ (particulate matter with an aerodynamic diameter less than 10 μm) and TSP (total suspended particulates) were sampled from Huainan city, China in December 2016 and May 2017. The contents of heavy metals in TSP are the highest, while those in PM_2.5 are the lowest. Zn, Mn, and Pb are the main components of heavy metals in Huainan atmospheric particulates. Straw burning activities may result in relatively higher atmospheric particulate matter content in summer than that in winter. The proportion of mineral particles in the studied particulate matters was the highest (40.79%), followed by soot aggregates (35.55%) and coal fly ash (19.74%). The results of energy spectrum analysis show that the main component of soot aggregates is C, and other contents are contributed by elements such as O and Si. Coal fly ash mainly contains C, O, Si, and a small amount of Al and Na. As, Cd, and Hg are the most easily enriched heavy metals. Industrial emissions, traffic discharges, coal combustion and dust emissions were found to be the main sources of heavy metals in atmospheric particulates.

The oxidative and neurotoxic potentials of the ambient PM2.5 extracts: The efficient multi-solvent extraction method

The health effects of ambient air particulate matter with a diameter of ≤2.5 μm (PM_2.5) on the central nervous system are well known and the induced oxidative stress has been shown as their main neuropathologic outcome. Ambient air PM_2.5 sampling methods mostly use air sampler systems that collect PM_2.5 on filters, which is followed by a PM_2.5 extraction approach. Inefficient extraction may lead to compositional bias and unreal interpretation of the results. This study aimed to compare our proposed multi-solvent extraction (MSE) approach for PM_2.5 extraction with a conventional aqueous extraction (AqE) method using the analysis of oxidative effects and cytotoxicity in the human neuroblastoma SH-SY5Y cell line. Ambient PM_2.5 samples were collected from an urban traffic location in Tehran city, the capital of Iran, using a high-volume sampler. The developed MSE method was proved to have superior advantages over the AqE method including an increased extraction efficiency (as much as 96 against 48% for PM_ms and PM_aq, respectively), and decreased artifacts and compositional biases. Ambient PM_2.5, besides PM_ms and PM_aq were analyzed for water-soluble ions, metals, and major elements. Dithiothreitol, ascorbic acid, lipid peroxidation, and cell viability assays on SH-SY5Y cells represented the significantly higher oxidative potential for PM_ms compared to PM_aq. The increased cytotoxicity may occur because of the increased oxidative potential of PM_ms and possibly is associated with higher efficiency of the MSE over the AqE method for removal of total redox-active PM components.

Influence of PM1 exposure on total and cause-specific respiratory diseases: a systematic review and meta-analysis

An increasing number of studies examined the potential effects of PM1 (submicronic particulate matter with an aerodynamic diameter ≤ 1 μm) on the risk of respiratory diseases; however, the results have been inconclusive. This study aimed to determine the overall association between PM1 with total and cause-specific respiratory diseases. A systematic review and meta-analysis was conducted with 68 related articles retrieved, and six articles met the full inclusion criteria for the final analysis. For a 10 μg/m3 increase in PM1, the pooled odds ratio (OR) was 1.05 (95% CI 0.98-1.12) for total respiratory diseases, 1.25 (95% CI 1.00-1.56) for asthma, and 1.07 (95% CI 1.04-1.10) for pneumonia with the I2 value of 87%, 70%, and 0%, respectively. Subgroup analyses showed that long-term exposure to PM1 was associated with increased risk of asthma (OR 1.47, 95% CI 1.33-1.63) with an I2 value of 0%, while short-term exposure to PM1 was not associated with asthma (OR 1.07, 95% CI 0.89-1.27) with the I2 value of 0%. Egger's test showed that publication bias existed (P = 0.041); however, the funnel plot was symmetrical with the inclusion of the moderator. In conclusion, elevated levels of PM1 may increase morbidity in total and cause-specific respiratory diseases in the population.

The PM2.5-bound polycyclic aromatic hydrocarbon behavior in indoor and outdoor environments, part II: Explainable prediction of benzo[a]pyrene levels

Among the polycyclic aromatic hydrocarbons (PAH), benzo[a]pyrene (B[a]P) has been considered more relevant than other species when estimating the potential exposure-related health effects and has been recognized as a marker of carcinogenic potency of air pollutant mixture. The current understanding of the factors which govern non-linear behavior of B[a]P and associated pollutants and environmental processes is insufficient and further research has to rely on the advanced analytical approach which averts the assumptions and avoids simplifications required by linear modeling methods. For the purpose of this study, we employed eXtreme Gradient Boosting (XGBoost), SHapley Additive exPlanations (SHAP) attribution method, and SHAP value fuzzy clustering to investigate the concentrations of inorganic gaseous pollutants, radon, PM_2.5 and particle constituents including trace metals, ions, 16 US EPA priority PM_2.5-bound PAHs and 31 meteorological variables, as key factors which shape indoor and outdoor PM_2.5-bound B[a]P distribution in a university building located in the urban area of Belgrade (Serbia). According to the results, the indoor and outdoor B[a]P levels were shown to be highly correlated and mostly influenced by the concentrations of Chry, B[b]F, CO, B[a]A, I[cd]P, B[k]F, Flt, D[ah]A, Pyr, B[ghi]P, Cr, As, and PM_2.5 in both indoor and outdoor environments. Besides, high B[a]P concentration events were recorded during the periods of low ambient temperature (<12 °C), unstable weather conditions with precipitation and increased soil humidity.

Real ambient particulate matter-induced lipid metabolism disorder: Roles of peroxisome proliferators-activated receptor alpha

A growing body of evidence associated particulate matter (PM) exposure with lipid metabolism disorders, yet, the underlying mechanism remains to be elucidated. Among the major lipid metabolism modulators, peroxisome proliferator-activated receptor (PPAR) alpha plays an important role. In the current study, an individually ventilated cage (IVC) system was used to expose C57/B6 mice to real-ambient PM for six weeks, with or without co-treatment of PPAR alpha agonist WY14,643. The general parameters, liver and adipose tissue pathology, serum lipids, metal deposition and lipid profile of liver were assessed. The results indicated that six weeks of real-ambient PM exposure induced dyslipidemia, including increased serum triglycerides (TG) and decreased high density lipoprotein cholesterol (HDL-C) level, along with steatosis in liver, increased size of adipocytes in white adipose tissue (WAT) and whitening of brown adipose tissue (BAT). ICP-MS results indicated increased Cr and As deposition in liver. Lipidomics analysis revealed that glycerophospholipids and cytochrome P450 pathway were most significantly affected by PM exposure. Several lipid metabolism-related genes, including CYP4A14 in liver and UCP1 in BAT were downregulated following PM exposure. WY14,643 treatment alleviated PM-induced dyslipidemia, liver steatosis and whitening of BAT, while enhancing CD36, SLC27A1, CYP4A14 and UCP1 expression. In conclusion, PPAR alpha pathway participates in PM-induced lipid metabolism disorder, PPAR alpha agonist WY14,643 treatment exerted protective effects on PM-induced dyslipidemia, liver steatosis and whitening of BAT, but not on increased adipocyte size of WAT.

Characterization and source identification of submicron aerosol during serious haze pollution periods in Beijing

Submicron aerosol is of extensive concern not only due to its significant impact on air quality but also because it is detrimental to human health. In this study, we investigated the characteristics, sources and chemical processes of submicron aerosol based on real-time online measurements of submicron aerosols (NR-PM₁) during December 2015 at an urban site in Beijing. The average mass concentration of NR-PM₁ was 92.5±84.9 µg/m³, the hourly maximum was 459.1 µg/m³ during the entire observation. The organic aerosol (OA) (55%) was the largest contributor to NR-PM₁. The average mass concentration of PAHs was 0.217±0.247 µg/m³, exhibiting the highest concentration at night and the lowest levels in the daytime. The average mass concentration of organic nitrate was 2.52±2.36 µg/m³ and that of inorganic nitrate was 7.62±8.22 µg/m³, accounting for 36% and 64%, respectively, of the total nitrate mass. Positive matrix factorization (PMF) differentiated the OA into five chemical components including LV-OOA, SV-OOA, COA, HOA and CCOA, accounting for 22%, 16%, 13%, 25% and 24% respectively, of the total OA. The average NR-PM₁ mass concentration on the heavy polluted days (HPD) was 182.8±70.2 µg/m³, which was approximately 9 times that on clean days (CD). The enhanced secondary formation of SNA was evident on HPD, especially the rapid increase of sulfate (23%) and nitrate (19%).

PM2.5 induces inflammatory responses via oxidative stress-mediated mitophagy in human bronchial epithelial cells

BACKGROUND

Fine particulate matter (PM_2.5) is a ubiquitous air pollutant, and it has been reported to be closely associated with lung inflammatory injury. In this study, the potential molecular mechanisms underlying PM_2.5-induced cellular inflammation in human bronchial epithelial (BEAS-2B) cells were investigated.

MATERIALS AND METHODS

Ambient PM_2.5 particulates from Suzhou, China, were collected and re-suspended in ultrapure water. Cellular damages, characterized by oxidative stress, mitochondrial injury, and inflammatory cytokine production, were determined in 24 h PM_2.5-treated BEAS-2B cells with or without 3-methyladenine (3-MA; autophagy inhibitor) pretreatment. Biomarkers related to oxidative damage, inflammatory injury and autophagy signaling pathways were also measured.

RESULTS

Uptake of PM_2.5 in BEAS-2B cells induced cellular oxidative damage, mitochondrial injury, and inflammatory responses as indicated by a significant decrease in GSH/GSSG ratio, increased MDA content, dilated mitochondria with loss and rupture of crista, and production of inflammatory cytokines. Activation of Nrf-2/TXNIP-mediated NF-κB and Bnip3L/NIX-dependent mitophagy signaling pathways, as well as accumulation of autophagosomes and autolysosomes, were also observed. A 6 h pretreatment of 3-MA increased PM_2.5-induced oxidative damage and cellular inflammation as indicated by increasing protein levels of HO-1, TXNIP, Bnip3L/NIX and IL-8 gene expression.

CONCLUSIONS

PM_2.5 induced cellular inflammatory injury by oxidative stress, mitochondrial dysfunction, and mitophagy initiation. Although induction of Bnip3L/NIX-mediated mitophagy in BEAS-2B cells appeared to confer protection in response to PM_2.5, dysfunction of autophagic flux may be a critical contributor to defective mitophagy and cellular inflammatory response.

The effect of PM2.5-related hazards on biomarkers of bronchial epithelial cells (A549) inflammation in Karaj and Fardis cities

Fine particles (especially PM_2.5 particles) in ambient air can cause irreversible effects on human health. In the present study, seasonal variations in toxicity PM_2.5 (cell viability and release of pro-inflammatory cytokines) were exposed human lung cells (A549) to concentrations of PM_2.5 samples in summer (sPM_2.5) and winter (wPM_2.5) seasons. Cells were separately exposed to three concentrations of PM_2.5 (25, 50, and 100 μg/mL) and three times (12 h, 1 and 2 days). We evaluated cell viability by MTT assay [3- (4, 5-dimethylthiazol-2-yl) -2, 5-diphenyltetrazolium bromide] and liberation of pro-inflammatory cytokines (interleukin-6 and interleukin-8) by the ELISA method. The toxicological results of this study showed that increasing the concentration of PM_2.5 particulates and contact time with it reduces cell viability and increases inflammatory responses. Seasonal cytotoxicity of PM_2.5 particles in high-traffic areas at summer season compared to winter season was lower. The lowest percent of viability at 2 days of exposure and 100 μg/mL exposure in the winter sample was observed. Also, PM_2.5 particles were influential in the amount of interleukins 8 and 6. The average release level of IL-6 and IL-8 in the cold season (winter) and the enormous exposure time and concentrations (2 days-100 μg/mL) was much higher than in the hot season (summer). These values were twice as high for winter PM_2.5 samples as for summer samples. The compounds in PM_2.5 at different seasons can cause some biological effects. The samples' chemical characteristics in two seasons displayed that the PMs were diverse in chemical properties. In general, heavy metals and polycyclic aromatic hydrocarbons were more in the winter samples. However, the samples of wPM_2.5 had a lower mass quota of metals such as aluminum, iron, copper, zinc, and magnesium. Concentrations of chromium, cadmium, arsenic, mercury, nickel, and lead were more significant in the sample of wPM_2.5.

Effect of ambient air PM2.5-bound heavy metals on blood metal(loid)s and children's asthma and allergy pro-inflammatory (IgE, IL-4 and IL-13) biomarkers

BACKGROUND

We investigated the concentrations of metals in fine particulate matter PM_2.5 in the outdoor air around the home sites of 123 male children from Ahvaz, average age 7.56, along with their blood samples to measure pro-inflammatory responses (Immunoglobulin E and cytokines: IgE, IL-4 and IL-13).

METHODS

We measured 6 metals (As, Cd, Cr, Hg, Ni and Pb) in three Ahvaz's regions including industrial (Padad), vehicle traffic (Golestan) and control (Kianpars).

RESULTS

The higher concentrations of metals in the Padad as the industrial ambient air i.e., arsenic, cadmium, chromium, mercury and nickel coincided with the higher concentrations of those metals in exposed children (P < 0.05) versus the controls. Children in Golestan, the high traffic air pollution area had the highest lead concentrations (p < 0.05). Also a significant association was shown in Padad between blood arsenic and IgE (β = 26.59, P < 0.001), IL-4 (β = 172.1, P < 0.001) and IL-13 (β = 14.84, P < 0.001), blood chromium and IgE (β = 10.38, P < 0.001), IL-4 (β = 75.27, P < 0.001) and IL-13 (β = 5.27, P < 0.001) and blood mercury and IgE (β = 13.11, P < 0.001), IL-4 (β = 108.09, P < 0.001) and IL-13 (β = 7.96, P < 0.001) and blood lead and IgE(β = 0.92, P = 0.025), IL-4(β = 7.16, P < 0.001) and IL-13(β = 0.58, P = 0.003). However, no significant relation was found for Cadmium, Nickel in blood with IgE, IL-4 and IL-13 levels. Moreover, children from industrial areas showed significantly higher concentrations of IgE (mean = 146.44 pg/200landa, P < 0.001), IL-4 (mean = 548.23 pg/200landa, P < 0.001) and IL-13 (mean = 52.93 pg/200landa, P < 0.001) versus Golestan and Kianpars.

CONCLUSION

Children residing in an industrial area with high concentrations of metals in PM_2.5 had high metals in blood and high production of IgE, IL-4 and IL-13, reflecting an immune dysregulation and brisk inflammatory responses.

Evaluation of life expectancy loss associated with submicron and fine particulate matter (PM1 and PM2.5) air pollution in Nanjing, China

Particulate matters with an aerodynamic diameter ≤1 μm (PM₁) significantly increased mortality risk, and the effect of PM₁ was even greater than that of PM_2.5 (aerodynamic diameter ≤2.5 μm). But the quantitative impact of PM₁ on life expectancy was unknown. We aim to examine the extent to which that people's life expectancy was shortened by PM₁ and PM_2.5. We obtained daily data on deaths, PM₁ and PM_2.5 records, and weather variables during 2016-2017 in Nanjing, China. Years of life lost (YLLs) were calculated by matching each decedent's age and sex to the Chinese life table. The fitted nonlinear dose-response associations of YLLs with PM₁ and PM_2.5 were estimated by utilizing a generalized additive model with a Gaussian link that controlled for confounding factors including meteorological variables, day of week, and long-term trend and seasonality. The effect estimates were presented as the YLLs when PM₁ and PM_2.5 concentrations fell in different ranges. Life expectancy losses attributable to PM₁ and PM_2.5 were calculated. Stratified analyses were also performed by age, sex, and death causes. Significant PM-YLL associations were observed, with greater increases in YLLs associated with PM₁ (68.9 thousand). PM₁ was estimated to reduce life expectancy, which was greater than PM_2.5 (PM₁: 1.67 years; PM_2.5: 1.55 years). For PM₁, greater years of loss in PM-related life expectancy were found in the female group, ≥65 years group, and cardiovascular disease group. Exposure to PM₁ had a greater impact on life expectancy loss than did PM_2.5. Constant efforts are urgently needed to control PM₁ air pollution to improve people's longevity.

The Influence of Transport on PAHs and Other Carbonaceous Species’ (OC, EC) Concentration in Aerosols in the Coastal Zone of the Gulf of Gdansk (Gdynia)

The aim of this study was to determine the influence of transport on the concentration of carbon species in aerosols collected in the coastal zone of the Gulf of Gdansk in the period outside the heating season. Elemental carbon (EC), organic carbon (OC), and the ΣPAHs5 concentrations were measured in aerosols of two size: <3 μm (respirable aerosols) and >3 μm in diameter (inhalable aerosols). Samples were collected between 13 July 2015 and 22 July 2015 (holiday period) and between 14 September 2015 and 30 September 2015 (school period). In both periods samples were taken only during the morning (7:00–9:00 a.m.) and afternoon (3:00–5:00 p.m.) road traffic hours. The highest mean values of the ΣPAHs5 and EC were recorded in small particles during the school period in the morning road traffic peak hours. The mean concentration of OC was the highest in small aerosols during the holiday period. However, there were no statistically significant differences between the concentrations of organic carbon in the morning and afternoon peak hours. Strict sampling and measurement procedures, together with the analysis of air mass backward trajectories and pollutant markers, indicated that the role of land transport was the greatest when local to regional winds prevailed, bringing pollution from nearby schools and the beltway.

Indoor/outdoor relationships, signatures, sources, and carcinogenic risk assessment of polycyclic aromatic hydrocarbons-enriched PM2.5 in an emerging port of northern China

Humans spend most of their time in indoor environments, thus a thorough understanding of indoor and outdoor PM_2.5-bound polycyclic aromatic hydrocarbons (PAHs) origins for accurate assessment of health risks is required. In the present study, 84 pairs of PM_2.5 samples from indoor (laboratory) and outdoor (campus) locations were collected from April to December 2018 in Caofeidian, China. The annual median concentration of PM_2.5 outdoors was 90.80 µg/m³, 9.08 times higher than the annual standard of WHO guideline (10 µg/m³). Indoor PM_2.5 annual median concentration (41.80 µg/m³) was also higher than the annual standard of ASHRAE guideline (15 µg/m³). The annual median concentrations of ∑₁₈PAHs indoors (44.23 ng/m³) and outdoors (189.6 ng/m³) were highest in winter and descended in the order of autumn > spring > summer. Contrary to summer and autumn, indoor/outdoor concentration ratios were less than 1 in spring and winter, indicating that the contribution of outdoor particle infiltration was more significant than that of indoor sources. The positive matrix factorization model suggested that indoor PAHs came from three sources: vehicle emissions (43%), biomass burning (37%), industry emissions, and coal combustion (20%). Outdoor PAHs came from four sources: petroleum volatilization (39%), vehicle emissions (30%), coal combustion (18%), and biomass burning (13%). The incremental lifetime cancer risk values of indoor and outdoor PAHs in winter exceeded the acceptable level (10^-6), and the carcinogenic risk of adults was higher than that of children and teenagers. These results indicated that simultaneous monitoring of indoor and outdoor PAHs is recommended for accurate assessment of health risk, and the analysis in the current work should be helpful to formulate policies to reduce PAHs emissions.

Airborne particulate matter upregulates expression of early and late adhesion molecules and their receptors in a lung adenocarcinoma cell line

BACKGROUND

Epidemiological evidence associates chronic exposure to particulate matter (PM) with respiratory damage and lung cancer. Inhaled PM may induce systemic effects including inflammation and metastasis. This study evaluated whether PM induces expression of adhesion molecules in lung cancer cells promoting interaction with monocytes.

METHODS

The expression of early and late adhesion molecules and their receptors was evaluated in A549 (human lung adenocarcinoma) cells using a wide range of concentrations of PM_2.5 and PM₁₀. Then we evaluated cellular adhesion between A549 cells and U937 (human monocytes) cells after PM exposure.

RESULTS

We found higher expression of both early and late adhesion molecules and their ligands in lung adenocarcinoma cells exposed to PM_2.5 and PM₁₀ particles present in the air pollution at Mexico City from 0.03 μg/cm² with a statistically significant difference (p ≤ 0.05). PM₁₀ had stronger effect than PM_2.5. Both PM also stimulated cellular adhesion between tumor cells and monocytes.

CONCLUSIONS

This study reveals a comprehensive expression profile of adhesion molecules and their ligands upregulated by PM_2.5 and PM₁₀ in A549 cells. Additionally these particles induced cellular adhesion of lung cancer cells to monocytes. This highlights possible implications of PM in two cancer hallmarks i.e. inflammation and metastasis, underlying the high cancer mortality associated with air pollution.

Airborne particulate matter in Tehran's ambient air

In recent decades, particulate matter (PM) concentrations in Tehran have exceeded the World Health Organization's (WHO) guideline on most days. In this study, a search protocol was defined by identifying the keywords, to carry out a systematic review of the concentrations and composition of PM in Tehran's ambient air. For this purpose, searches were done in Scopus, PubMed, and Web of Science in 2019. Among the founded articles (197 in Scopus, 61 in PubMed, and 153 in Web of Science). The results show that in Tehran, the annual average PM₁₀ exceeded the WHO guidelines and for more than 50.0% of the days, the PM_2.5 concentration was more than WHO 24-h guidance value. The PM concentration in Tehran has two seasonal peaks due to poorer dispersion and suspension from dry land, respectively. Tehran has two daily PM peaks due to traffic and changes in boundary-layer heights; one just after midnight and the other during morning rush hour. Indoor concentrations of PM10 and PM2.5 in Tehran were 10.6 and 21.8 times higher than the corresponding values in ambient air. Tehran represents a unique case of problems of controlling PM because of its geographical setting, emission sources, and land use. This review provided a comprehensive assessment for decision makers to assist them in making appropriate policy decisions to improve the air quality. Considering factors such as diversity of resources, temporal and spatial variations, and urban location is essential in developing control plans. Also future studies should focus more on PM reduction plans.

Characterization, possible sources and health risk assessment of PM2.5-bound Heavy Metals in the most industrial city of Iran

Air pollution associated with particulate matters results in different types of disease including allergy, lung destruction, heart failure, and related problems. This study has been designed and performed to examine the concentration of PM_2.5-bound heavy metals, risk assessment, possible sources and effect of meteorological parameters on 17 sites of the air of the most industrial city of Iran (Karaj) in 2018-19. For this purpose, four samples were taken from every point of Karaj air over one year using a pump (Leland Legacy (SKC)) with flow rate of 3 L/min on PTFE filter for 24 h. Overall, 68 samples of PM_2.5-bound heavy metals were collected. Note that during the sampling, atmospheric parameters including temperature, pressure, humidity, and wind speed were regularly recorded using PHB318 portable device. In examining the chemical composition of these particles, the concentration of metals (Al-Zn- Ar-Cd-Cr-Cu-Fe-Hg-Mn-Ni-Pb) was determined after digestion of the collected samples and through injection into ICP-OEC device. The results indicated that the mean annual concentration of PM_2.5 particles range from 21.84 to 72.75 µg/m³. The mean concentration of heavy metals lied within the range of 25.63 to 336.27 ng/m³. Among heavy metals, the maximum concentration belonged to aluminum (277.95 ng/m³) and iron (336.27 ng/m³), which are known as elements with a ground source (sources such as car fuels, exhaust gases, decorative materials, batteries, indoor smoking, the paint used for painting walls, erosion and corrosion of rubber of cars). Meanwhile, there was a positive relationship between heavy metals and temperature(r: 0.418, p < 0.019), pressure (r: 0.184, p < 0.0.402), as well as wind speed (r: 0.38, p < 0.017), while an inverse relationship was observed with relative humidity (r: -0.219, p < 0.018). The ecological risk of the metals calculated was very notable, with the maximum environmental risk being related to cadmium in children (6.61) and manganese in adults (0.82). The largest HQ in children and adults was associated with Cr. Finally, ILCR values for cadmium in both children (1.19 E-04) and adult (4.81 E-04) groups indicated high risk of developing cancer in humans.

Chemical constituents and sources of indoor PM2.5 and cardiopulmonary function in patients with chronic obstructive pulmonary disease: Estimation of individual and joint effects

BACKGROUND

The cardiopulmonary effects of chemical constituents and sources of indoor fine particulate matter (PM_2.5) remain unclear.

OBJECTIVES

To examine the individual and joint effects of constituents of indoor PM_2.5 on cardiopulmonary function of patients with chronic obstructive pulmonary disease (COPD) and the role of identified sources.

METHODS

This panel study recruited 43 stable COPD patients from November 2015 to May 2016 in Beijing, China. Daily indoor and outdoor PM_2.5 were collected for five consecutive days simultaneously. Twenty-four elements were measured and principal component analysis was used for source appointment. Pulmonary function and blood pressure (BP) were also measured at daily visit. The linear mixed-effect models were used to estimate the effect of each constituent and source. Bayesian kernel machine regression (BKMR) models were used to estimate the overall effect of all measured constituents.

RESULTS

The combustion, indoor soil/dust and road dust sources were identified as the main sources of indoor PM_2.5 and combustion sources contributed over 40% during the heating season. Most constituents were significantly associated with elevated BP of COPD patients and the joint effects of mixed exposures were also significant especially during the heating season. Most associations of chemical constituents with pulmonary function were negative but not statistically significant during the heating season, as was the joint effect. Few associations were observed during the non-heating season. Further, we observed combustion sources throughout the study period and road dust sources during the heating season were significantly associated with increased BP but not decreased pulmonary function.

CONCLUSION

The combustion and road dust sources and their related constituents of indoor PM_2.5 could cause adverse effects on cardiovascular function of COPD patients especially during the heating season, but the effect on pulmonary function still needs to be further studied.

Assessment of incremental lifetime cancer risks of ambient air PM10-bound PAHs in oil-rich cities of Iran

This study investigates the concentrations of PM₁₀-bound PAHs and their seasonal variations in three cities of Ahvaz, Abadan, and Asaluyeh in Iran. The mean concentrations of PM₁₀ in two warm and cold seasons in Ahvaz were higher and in Abadan and Assaluyeh were lower than the national standard of Iran and the guidelines of the World Health Organization. The Σ16 PAHs concentration in ambient air PM₁₀ during the cold season in Ahvaz, Abadan and Asaluyeh was 244.6, 633, and 909 ng m^- 3, respectively, and during the warm season in Ahvaz, Abadan, and Asaluyeh was 242.1, 1570 and 251 ng m^- 3, respectively. The high molecular weight PAHs were the most predominant components. The most abundant PAHs species were Pyr, Chr, B [ghi] P, and Flt. The results showed that the total PAHs concentration in the cold and warm seasons was dependent on industrial activities, particularly the neighboring petrochemical units of the city, vehicular exhausts, traffic and use of oil, gas, and coal in energy production. The total cancer risk values as a result of exposure to PAHs in ambient air PM₁₀ in all three cities for children and adults and in both cold and warm seasons were between 1 × 10^- 6 and 1 × 10^- 4, and this indicates a potential carcinogenic risk. Therefore, considering the various sources of air pollutants and its role on people's health, decision makers should adopt appropriate policies on air quality to reduce the ambient air PAHs and to mitigate human exposure.

Polycyclic aromatic hydrocarbons in PM1, PM2.5 and PM10 atmospheric particles: identification, sources, temporal and spatial variations

This study reports temporal and spatial variations of 16 different species of particulate polycyclic aromatic hydrocarbons (particle-bonded PAHs) in the indoor and outdoor environments of three sampling sites in Bandar Mahshahr city, Iran. A low-volume air sampler was employed to collect size-segregated particulate matter during winter (October to December 2015), and summer (July to September 2016). The results showed that the annual concentrations of indoor and outdoor PM10 and PM2.5 were much higher than the related World Health Organization guidelines. The concentration of total particle-bonded PAHs (TPAHs) was higher in winter than in summer and a significant difference between the two sampling seasons was observed. The indoor and outdoor carcinogenic PAHs to TPAHs concentrations ratios in the sampling sites in summer and winter were as follow: for PM10 40.15-42.51%, PM2.5 41.30-42.97%, and PM1 43.07-44.36%, respectively; furthermore, the smaller the particle size, the higher the percentage of carcinogenic PAHs. 2 ring PAHs had a very small contribution to the total PAHs (about 1%), whereas PAHs with 3-to-4 rings had much larger contributions, ranging from 71.65% to 75.17%. The results demonstrated that as PM size decreased, the proportion of 5-to-6-ring PAHs to the total PAHs increased. Since 5-to-6- ring PAHs are considered to be more toxic, hence more attention should be paid to fine particles. The diagnostic ratios of indoor and outdoor of three sampling sites in both seasons suggested that petrogenic sources, as well as combustion of petroleum and other fossil fuels were the main PAHs sources.

Blood lead level monitoring related to environmental exposure in the general Iranian population: a systematic review and meta-analysis

Exposure to lead can cause adverse health problems incorporating hypophosphatemia, heart and liver disease, cancers, neurological and cardiovascular diseases, central nervous disorders, and sensory disorders. This study investigated the blood lead level in the general Iranian population with environmental exposure to lead. In the presented systematic review and meta-analysis, the authors searched Iranian dataset, including Magiran, SID, Iranmedex, and Nopa, and the main dataset, comprising PubMed, Scopus, Embase, and Web of Science, all available articles until 12 January 2019, and extracting 55 studies (with 63 data for analysis) to a meta-analysis. A comprehensive meta-analysis software, pooled standard deviation, mean, sample size, and the utterly random effects model was analyzed in this study. The results showed that the overall mean BLL (95% CI) in total inquiries was 6.41 μg/dL (5.96 to 6.87). Besides, the results for gender and age subgroups were as follows: mean BLL, 6.47 μg/dL, 95% CI, 5.79, to 7.15, mean BLL, 6.44 μg/dL, 95% CI, 5.96, to 6.91, respectively. Conclusively the mean BLL in the Iranian population was higher than the recommended level by the US Centers for Disease Control and Prevention (CDC). Results indicated that the mean BLL in men and adults was more elevated than in women and children, respectively. Therefore, BLL monitoring and screening of the general Iranian population are is necessary to determine a reference value.

Occurrence, spatial distribution, seasonal variations, potential sources, and inhalation-based health risk assessment of organic/inorganic pollutants in ambient air of Tehran

The present study evaluated the concentrations, spatial distribution, seasonal variations, potential sources, and risk assessment of organic/inorganic pollutants in ambient air of Tehran city. Totally, 180 air samples were taken from 9 sampling stations from March 2018 to March 2019 and were analyzed to determine the concentrations of organic pollutants (BTEX compounds and PM_2.5-bound PAHs) plus inorganic pollutants (PM_2.5-bound metals and asbestos fibers). The results revealed that the mean concentrations of ∑ PAHs, BTEX, ∑ heavy metals, and asbestos fibers were 5.34 ng/m³, 60.55 µg/m³, 8585.12 ng/m³, and 4.13 fiber/ml in the cold season, respectively, and 3.88 ng/m³, 33.86 µg/m³, 5682.61 ng/m³, and 3.21 fiber/ml in the warm season, respectively. Source apportionment of emission of the air pollutants showed that PAHs are emitted from diesel vehicles and industrial activities. BTEX and asbestos are also released mainly by vehicles. The results of the inhalation-based risk assessment indicated that the carcinogenic risk of PAHs, BTEX, and asbestos exceeded the recommended limit by The US environmental protection agency (US EPA) and WHO (1 × 10^-4). The risk of carcinogenesis of heavy metal of lead and chromium also exceeded the recommended limit. Thus, proper management strategies are required to control the concentration of these pollutants in Tehran's ambient air in order to maintain the health of Tehran's citizens.