A comprehensive study on spatio-temporal distribution, health risk assessment and ozone formation potential of BTEX emissions in ambient air of Delhi, India

A comprehensive study on the spatial and temporal variation of BTEX and asbestos in the northwest of Iran: Human risk assessment

Substances like asbestos and other air pollutants, such as BTEX (benzene, toluene, ethylbenzene, and xylene), are hazardous compounds due to their adverse effects on human health. This study aims to investigate the levels, seasonal variations, spatial distribution, potential sources, and associated health risks associated with BTEX compounds and asbestos fibers in the ambient air of Tabriz. Air samples were taken at 16 different locations during the 2020-2021 period. Glass containers with charcoal were used for sample collection, and the BTEX content was determined using the GC-FID method. Phase-contrast microscopy (PCM) analysis was conducted with a low-volume peripheral pump for asbestos fiber sampling. The results showed that the average concentration of ∑BTEX was 37.94 and 27.98 μg/m3 in autumn and spring, respectively. The same parameter was 2.26 and 1.68 f/L for asbestos in the autumn and winter, respectively. The contribution of BTEX to ozone formation potential (OFP) in the research area showed that xylene and toluene were the major contributors to ozone production in different seasons. The risk of exposure to benzene compounds was 24 × 10-4 in children and 55.9 × 10-4 in adults, while the risk of exposure to ethylbenzene was 3.78 × 10-4 in children and 3.25 × 10-4 in adults. The estimated lifetime cancer risk was found to be the highest for benzene, followed by ethylbenzene. The estimated cancer risk for benzene and ethylbenzene exceeded the threshold values set by EPA, which signals a significant carcinogenic risk due to exposure to these substances in the ambient air of Tabriz. According to the EPA guidelines, the low carcinogenicity risk levels are between 10-4 and 10-6. According to the findings for the exposure to asbestos fibers, the maximum values of excess cancer risk (ECR) and estimated lifetime cancer risk (ELCR) were observed in the 16-30 age range across all locations, suggesting increased exposure to asbestos fibers compared to other age groups.

Risk assessment of Benzene, Toluene, Ethyl benzene, and Xylene (BTEX) in the atmospheric air around the world: A review

Volatile organic compounds, such as BTEX, have been the subject of numerous debates due to their detrimental effects on the environment and human health. Human beings have had a significant role in the emergence of this situation. Even though US EPA, WHO, and other health-related organizations have set standard limits as unhazardous levels, it has been observed that within or even below these limits, constant exposure to these toxic chemicals results in negative consequences as well. According to these facts, various studies have been carried out all over the world - 160 of which are collected within this review article, so that experts and governors may come up with effective solutions to manage and control these toxic chemicals. The outcome of this study will serve the society to evaluate and handle the risks of being exposed to BTEX. In this review article, the attempt was to collect the most accessible studies relevant to risk assessment of BTEX in the atmosphere, and for the article to contain least bias, it was reviewed and re-evaluated by all authors, who are from different institutions and backgrounds, so that the insights of the article remain unbiased. There may be some limitations to consistency or precision in some points due to the original sources, however the attempt was to minimize them as much as possible.

Mono and polycyclic aromatic hydrocarbons in waterpipe wastewater: Level and ecotoxicological risk assessment

Increasing of tobacco consumption around the world has led to the production of a large volume of waterpipe wastewater that enter the environment (e.g., coastal areas)and threaten aquatic creatures. However, until now, no research has been carried out on the amounts of monocyclic and polycyclic aromatic hydrocarbons (PAHs) in hookah wastewater. In the current study, the levels of PAHs and BTEX compounds in waterpipe wastewater resulting from the use of different tobacco brands were determined and their eco-toxicological effects were also evaluated. The mean levels of ƩPAHs in waterpipe wastewater of Al Tawareg, Al-Fakher, Nakhla, Tangiers and traditional tobacco brands samples were 3.48 ± 1.65, 3.33 ± 1.52, 3.08 ± 1.25, 2.41 ± 0.87 and 0.70 ± 0.13 μg/L, respectively. The mean levels of ƩBTEX in waterpipe wastewater of Al Tawareg, Al-Fakher, Nakhla, Tangiers and traditional tobacco brands samples were also 2.53 ± 0.61, 2.65 ± 0.78, 2.51 ± 0.72, 2.35 ± 0.56, and 0.78 ± 0.12 μg/L, respectively. The maximum level of PAHs and BTEX compounds in all brands/flavors samples were for naphthalene (Naph) and toluene, respectively. The concentrations of some PAHs (fluoranthene (Flrt), anthracene (Ant), benzo(b)fluoranthene (BbF), benzo(b)fluoranthene (BkF), benzo (g,h,i)perylene (BghiP) and dibenzo (a, h) anthracene (DahA)) and BTEX compounds (benzene) in the waterpipe wastewater samples were more than recommended guidelines and standards by the international reputable organizations such as World Health Organization (WHO) for water quality. Waterpipe wastewater can be introduced as an important origin for the release of these dangerous contaminants into the environmental matrixes. Therefore, more stringent regulations should be considered for the safe disposal of such hazardous wastes including waterpipe wastewater.

VOC source apportionment, reactivity, secondary transformations, and their prioritization using fuzzy-AHP method in a coal-mining city in India

This study assessed the air quality status in different functional zones of Dhanbad-a coal-mining and industrial hub, based on the measurement of aromatic and halogenated volatile organic compounds (VOCs) using gas chromatography. The study encompasses source apportionment of VOCs and their chemical reactivity in terms of OH radical loss rate (LOH), ozone-forming potential (OFP), and their secondary organic aerosol forming potential (SOAp). Furthermore, prioritization of VOCs based on a fuzzy-analytical hierarchical process (F-AHP) has also been done. The results found xylene species to have the highest concentration in all three seasons across traffic-intersection and industrial zones and toluene at the institutional zone. The study identified four sources using positive matrix factorization (PMF) model, viz., mixed traffic exhaust (35%), coal combustion sources (30%), industrial (26%), and solvent usage (9%). LOH and SOAp were ~ 16 times more at the industrial and traffic-intersection zone than the institutional zone. The aromatic species contributed 97% to the OFP, and many species exhibited less contribution to the mixing ratio of VOCs but displayed a high contribution to LOH, OFP, and SOAp, suggesting the need to prefer reactivity-based strategies in addition to concentration-based strategies in the future for their regulation. The F-AHP-based priority component analysis identified 16 species out of 29 in the priority watch list (nine in tier-1, four in tier-2, and three in tier-3). The paucity of data and lack of ambient air quality standards on VOCs (except benzene) make it difficult to determine which aspect should be dealt with first and which species require more attention. Therefore, the F-AHP method used in this study could help identify the influencing parameters to be considered while devising efficient VOC management policies.

Global perspective of municipal solid waste and landfill leachate: generation, composition, eco-toxicity, and sustainable management strategies

Globally, more than 2 billion tonnes of municipal solid waste (MSW) are generated each year, with that amount anticipated to reach around 3.5 billion tonnes by 2050. On a worldwide scale, food and green waste contribute the major proportion of MSW, which accounts for 44% of global waste, followed by recycling waste (38%), which includes plastic, glass, cardboard, and paper, and 18% of other materials. Population growth, urbanization, and industrial expansion are the principal drivers of the ever-increasing production of MSW across the world. Among the different practices employed for the management of waste, landfill disposal has been the most popular and easiest method across the world. Waste management practices differ significantly depending on the income level. In high-income nations, only 2% of waste is dumped, whereas in low-income nations, approximately 93% of waste is burned or dumped. However, the unscientific disposal of waste in landfills causes the generation of gases, heat, and leachate and results in a variety of ecotoxicological problems, including global warming, water pollution, fire hazards, and health effects that are hazardous to both the environment and public health. Therefore, sustainable management of MSW and landfill leachate is critical, necessitating the use of more advanced techniques to lessen waste production and maximize recycling to assure environmental sustainability. The present review provides an updated overview of the global perspective of municipal waste generation, composition, landfill heat and leachate formation, and ecotoxicological effects, and also discusses integrated-waste management approaches for the sustainable management of municipal waste and landfill leachate.

An Analysis of the Spatial Characteristics and Transport Fluxes of BTEX in Soil and Atmospheric Phases at a Decommissioned Steel Mill Site in China with a Long History

BTEX (benzene, toluene, ethylbenzene, and xylene), as characteristic pollutants in chemical plant sites, are widely present in the environment and pose a serious threat to the health and safety of nearby residents. Studying the spatial distribution characteristics and transport fluxes of BTEX in soil and air at contaminated sites and the health risks they pose to humans is of great significance for fine pollution control and environmental management. This study took a typical decommissioned steel plant as a case study. A total of 23 soil and air samples were collected from different locations to investigate the spatial distribution characteristics of BTEX in soil and air. The transport and fate of BTEX in soil and air were evaluated using the fugacity model, and finally, a human health risk assessment was conducted. The results indicate a relatively severe level of benzene pollution in both soil and air. The maximum exceedance factor of benzene in soil samples is 31.5, with the concentration exceedance depth at 1.5 m. The maximum concentration of benzene in air samples is 4.98 μg·m-3. Benzene, at 5.9% of the site, shows a low flux with negative values, while other components at various locations all exhibit a trend of transport from the soil phase to the atmospheric phase. Benzene is the pollutant that contributes the most to the transport flux from soil to air within the site. The coking area and sewage treatment area are key areas within the steel mill where BTEX accumulate easily in the soil. The non-carcinogenic risk values of the individual components of BTEX in the soil are below the acceptable risk level. However, the carcinogenic risk value of benzene in the children's exposure scenario exceeds the carcinogenic risk level of 10-6. The carcinogenic risk range of various components of BTEX in the air is 2.63 × 10-6~3.88 × 10-5, with 28.6% of the locations exceeding the threshold of 10-6. The range of the total HI (hazard index) is 2.08 × 10-4~1.81 × 10-1, all of which is below the safety threshold of 1. The results of this study will provide scientific support for the fine pollution control and environmental management of industrial contaminated sites with BTEX as their typical pollutants.

BTEX in Ambient Air of Zarand, the Industrial City in Southeast of Iran: Concentration, Spatio-temporal Variation and Health Risk Assessment

The existence of several industries in Zarand, a city in Southeastern Iran, caused challenges for the residents about air pollutants and associated health effects. In the present study, the concentration of benzene, toluene, ethylbenzene, and xylene (BTEX), spatio-temporal distribution and related health risks were evaluated. Passive samplers were used to collect 30 samples in the over the hot and cold periods in 2020. The ordinary Kriging method was used to predict the spatio-temporal distribution of BTEXs. Also, the Monte Carlo simulation was used to evaluate the related carcinogenic and non-carcinogenic risks of BTEX for adults. The ranking of mean concentration of overall toluene, xylene, ethylbenzene, and benzene followed as 82.49 ± 26.86, 30.91 ± 14.04, 4.75 ± 3.28, and 0.91 ± 0.18 µg/m3, respectively. The mean value of lifetime carcinogenic risk (LTCR) for residents related to benzene was 7.52 × 10- 6, indicating a negligible carcinogenic risk for them. Furthermore, the ranking of non-carcinogenic risk calculated through hazard quotient (HQ) for investigated BTEX compounds followed as xylene > benzene > toluene > ethylbenzene over the hot period and xylene > toluene > ethylbenzene over the cold period which all points had HQ < 1. Additionally, according to the findings of the sensitivity analysis, the concentration of benzene was the main contributor in increasing the carcinogenic risk. According to our results, it can be stated that the existence of several industries in the study area could not possibly occur the significant carcinogenic and non-carcinogenic risks to the adults residents in the study period. Human studies are recommended to determine definite results.

Assessment of health risk and burden of disease induced by exposure to benzene, toluene, ethylbenzene, and xylene in the outdoor air in Tehran, Iran

The health risk and burden of disease induced by exposure to benzene, toluene, ethylbenzene, and xylene (BTEX) in the outdoor air in Tehran, 2019 were assessed based on the data of five fixed stations with weekly BTEX measurements. The non-carcinogenic risk, carcinogenic risk, and disease burden from exposure to BTEX compounds were determined by hazard index (HI), incremental lifetime cancer risk (ILCR), and disability-adjusted life year (DALY), respectively. The average annual concentrations of benzene, toluene, ethylbenzene, and xylene in the outdoor air in Tehran were 6.59, 21.62, 4.68, and 20.88 μg/m³, respectively. The lowest seasonal BTEX concentrations were observed in spring and the highest ones occurred in summer. The HI values of BTEX in the outdoor air in Tehran by district ranged from 0.34 to 0.58 (less than one). The average ILCR values of benzene and ethylbenzene were 5.37 × 10^-5 and 1.23 × 10^-5, respectively (in the range of probable increased cancer risk). The DALYs, death, DALY rate (per 100,000 people) and death rate (per 100,000 people) induced by BTEX exposure in the outdoor air in Tehran were determined to be 180.21, 3.51, 2.07, and 0.04, respectively. The five highest attributable DALY rates in Tehran by district were observed in the districts 10 (2.60), 11 (2.43), 17 (2.41), 20 (2.32), and 9 (2.32), respectively. The corrective measures such as controlling road traffic and improving the quality of vehicles and gasoline in Tehran could reduce the burden of disease from BTEX along with the health effects of other outdoor air pollutants.

Spatiotemporal variations, photochemical characteristics, health risk assessment and mid pandemic changes of ambient BTEX in a west Asian metropolis

This study examined the concentration of BTEX in Tehran from 2018 to 2020 in five monitoring stations with different backgrounds, which has been accomplished using the combination of passive sampling and GC-FID method. The total concentration of BTEX was estimated to be 65.39 (µg/m3), with a higher average concentration in 2019-2020 (77.79 µg/m3) compared to 2018-2019 (53.48 µg/m3) due to the leaping concentration of Toluene in the pandemic era. Despite a Benzene concentration decline in recent years, the average annual concentration of Benzene (5.66 µg/m3) at five stations remained higher than the EU commission and India standards (5 µg/m3) as well as Japan and Iraq thresholds (3 µg/m3). Toluene dominated other species in terms of concentrations, mass distribution (~0.6%), followed by m,p-Xylene (~0.2%), Benzene (~0.05-0.1) and Ethylbenzene (< 0.05). The evidence regarding seasonal changes of BTEX in 2019 shows the maximum concentration of these compounds in autumn, which is probably due to heavier traffic compared to other seasons. In contrast, in the first half of 2020 (which encompasses the start of the pandemic period and urban lockdown), point sources seem to play a prominent role in concentration fluctuations, as confirmed by changes in interspecies relationships and lower traffic congestion. The highest mean concentrations were observed in high-traffic, residential and suburban sites, respectively. The study reveals that m,p-Xylene possess the highest Ozone formation potential (~109.46), followed by Toluene (~85.34), o-Xylene (~46.87), Ethylbenzene (~13.52) and Benzene (~2.61). Health risk assessment results indicated the high carcinogenic risk of Benzene (mean = 3.6 × 10-6) and the acceptable non-carcinogenic risk of BTEX (hazard index~0.03 < specified limit of 1). Finally, the estimated weighted exposures of BTEX emphasized that residents near the high-traffic districts are more exposed to BTEX.

Supplementary Information

The online version contains supplementary material available at 10.1007/s00477-023-02476-3.

The research hotspots and trends of volatile organic compound emissions from anthropogenic and natural sources: A systematic quantitative review

Volatile organic compound (VOC) emissions have attracted wide attention due to their impacts on atmospheric quality and public health. However, most studies reviewed certain aspects of natural VOCs (NVOCs) or anthropogenic VOCs (AVOCs) rather than comprehensively quantifying the hotspots and evolution trends of AVOCs and NVOCs. We combined the bibliometric method with the evolution tree and Markov chain to identify research focus and uncover the trends in VOC emission sources. This study found that research mainly focused on VOC emission characteristics, effects on air quality and health, and VOC emissions under climate change. More studies concerned on AVOCs than on NVOCs, and AVOC emissions have shifted with a decreasing proportion of transport emissions and an increasing share of solvent utilization in countries with high emissions and publications (China and the USA). Research on AVOCs is imperative to develop efficient and economical abatement techniques specific to solvent sources or BTEX species to mitigate the detrimental effects. Research on NVOCs originating from human sources risen due to their application in medicine, while studies on sources sensitive to climate change grew slowly, including plants, biomass burning, microbes, soil and oceans. Research on the long-term responses of NVOCs derived from various sources to climate warming is warranted to explore the evolution of emissions and the feedback on global climate. It is worthwhile to establish an emission inventory with all kinds of sources, accurate estimation, high spatial and temporal resolution to capture the emission trends in the synergy of industrialization and climate change as well as to simulate the effects on air quality. We review VOC emissions from both anthropogenic and natural sources under climate change and their effects on atmospheric quality and health to point out the research directions for the comprehensive control of global VOCs and mitigation of O₃ pollution.

Emission characteristics and inventory of volatile organic compounds from the Chinese cement industry based on field measurements

Volatile organic compounds (VOCs) are major precursors of ozone (O₃) and secondary organic aerosols (SOA), which degrade air quality and pose a serious risk to human health and ecological systems. Previous studies on the emission characteristics of VOCs have predominantly focused on petrochemical and solvent-using sources, while localized studies on the cement industry are scarce in China. Field measurements for four cement plants were carried out in this study to investigate the emission levels, source profiles, and secondary pollutant generation potential of 98 VOCs species emitted from rotary and shaft kilns in China. Furthermore, a species-differentiated VOCs emission inventory was compiled for the Chinese cement industry in 2019. The results demonstrated that the mass concentration of VOCs emitted from shaft kiln was more than 20-fold higher than that emitted from rotary kilns, and the alkanes was the dominant species (56%) in shaft kilns, while oxygenated VOCs (OVOCs) and halocarbons were the main species in rotary kilns. Moreover, alkenes & alkyne were the dominant contributors to ozone formation potential (OFP) in shaft kilns, whereas alkenes & alkyne and OVOCs were comparable and prominent contributors in rotary kilns. In contrast, secondary organic aerosol potential (SOAP) for the two types of kilns was dominated by aromatics. In 2019, approximately 18.18 kt VOCs were emitted from cement production and were found to be largely concentrated in the southeast and central provinces of China. Considering the influence on environmental conditions, high OFP-contributing species in cement kilns are suggested to be a priority in the pollution mitigation of O₃. This study provides a new, comprehensive, and reasonable cognition of the current VOCs emissions from both rotary and shaft kilns in China, which will aid in a better understanding of VOCs emission characteristics and guide future policy-making.

Volatile organic compounds and their contribution to ground-level ozone formation in a tropical urban environment

This study aims to determine the trends of volatile organic compound (VOC) concentrations and their potential contribution to O₃ formation. The hourly data (August 2017 to July 2018) for 29 VOCs were obtained from three Malaysian Department of Environment continuous air quality monitoring stations with different urban backgrounds (Shah Alam, Cheras, Seremban). The Ozone Formation Potential (OFP) was calculated based on the individual Maximum Incremental Reactivity (MIR) and VOC concentrations. The results showed that the highest mean total VOC concentrations were recorded at Cheras (148 ± 123 μg m^-3), within the Kuala Lumpur urban environment, followed by Shah Alam (124 ± 116 μg m^-3) and Seremban (86.4 ± 89.2 μg m^-3). VOCs such as n-butane, ethene, ethane and toluene were reported to be the most abundant species at all the selected stations, with overall mean concentrations of 16.6 ± 11.9 μg m^-3, 12.1 ± 13.3 μg m^-3, 10.8 ± 11.9 μg m^-3 and 9.67 ± 9.00 μg m^-3, respectively. Alkenes (51.3-59.1%) and aromatic hydrocarbons (26.4-33.5%) have been identified as the major contributors to O₃ formation in the study areas based on the overall VOC measurements. Relative humidity was found to influence the concentrations of VOCs more than other meteorological parameters. Overall, this study will contribute to further understanding of the distribution of VOCs and their contribution to O₃ formation, particularly in the tropical urban environment.

Investigation of VOC characteristics, source analysis, and chemical conversions in a typical petrochemical area through 1-year monitoring and emission inventory

To effectively investigate the characteristics, source analysis, and chemical conversions of volatile organic compounds (VOCs) pollution in a typical petrochemical area, 81 VOC species from nine sampling sites were collected from 1st January to 31th December 2019 in Jinshan District. Results showed the concentration of VOCs was 51.63 ± 36.05 ppbv, and VOCs were dominated by alkane (40.10%) and alkenes (39.91%). The temporal variations of VOCs showed that the highest average VOC concentration appeared in July, and the lowest concentration of VOCs was in February. The concentration of VOCs was mainly connected with industrial processes and was transported to other areas through the downwind direction. Six PMF-derived sources including petrochemical industry, solvent utilization, vehicle exhaust, fuel evaporation, combustion, and other industry processes, contributing 37.08%, 16.74%, 16.69%, 14.99%, 9.53%, and 4.97%, respectively. Meanwhile, an anthropogenic VOC emission inventory was established by emission factors and the activity statistics for 2019, results indicated that the total emission of VOCs was estimated as 6.22 kt, petrochemical industry was the most important contributor of human-produced VOCs. The L_OH concentration was 396.12 ppbv via OH radical loss rate method, and the OFP was 210.44 ppbv based on the MIR factor. Alkenes and aromatics were the important components of O₃ formation. This study provides effective information for corresponding governments to establish VOCs contamination control directives.

Characteristics and Impact of VOCs on Ozone Formation Potential in a Petrochemical Industrial Area, Thailand

In this study, the ambient concentrations of volatile organic compounds (VOCs) were intensively measured from January 2012 to December 2016 using an evacuated canister and were analyzed using a gas chromatography/mass spectrophotometer (GC/MS) based on the US EPA TO-15 in the community and industrial areas of the largest petroleum refinery and petrochemical industrial complex in Map Ta Phut Thailand. The ternary diagram was used to identify the source of VOCs. Reactivity of VOCs on their ozone formation potential (OFP) were quantified by the maximum incremental reactivity coefficient method (MIR) and propylene-equivalent concentration methods. Results from the study revealed that aromatic hydrocarbon was the dominant group of VOCs greatly contributing to the total concentration of measured VOCs. Among the measured VOCs species, toluene had the highest concentration and contributed as the major precursor to ozone formation. The ternary analysis of benzene:toluene:ethybenzene ratios indicated that VOCs mainly originated from mobile sources and industrial processes. Within the industrial area, measured VOC concentration was dominated by halogenated hydrocarbons, and alkene was the highest contributor to ozone formation. The propylene-equivalent concentration method was also used to evaluate the reactivity of VOCs and their role in ozone formation, and secondly to support findings from the MIR method.

Emission of BTEX compounds from the frying process: Quantification, environmental effects, and probabilistic health risk assessment

Frying is one of the cooking methods which generates mono aromatic hydrocarbons, including benzene, toluene, ethylbenzene, and xylene (BTEX); subsequently, it affects health through carcinogenic (CR) and non-carcinogenic risks (n-CR). However, their environmental effects known by secondary organic aerosols (SOA) and ozone formation potential (OFP) were also attended by many scientists. Therefore, this study quantified the BTEX emissions from 4 types of most commonly used edible oils (canola, corn, sunflower, and blend) under various frying conditions of temperatures and food additives. Furthermore, the effects of the chemicals in the light of health (CR and n-CR) and environment (SOA and OFP) were also investigated. The study results showed that higher temperatures could significantly increase the emissions, while the addition of food ingredients significantly reduces the emissions. The rank order of emitted chemical was obtained as T > B > E > X. The blend had the most emission among oils, followed by, in descending order, corn, sunflower, and canola. In association with environmental effects, the orders of X > T > E > B and T ∼ E > X > B were obtained for OFP and SOA, respectively. THQ for blend, corn, canola, and sunflower oils was higher than 1 (1.76, 1.35, 1.27, and 1.002, respectively), showing a considerable n-CR when the hood was off. In this respect, TCR for the oils (1.78 × 10^-4, 1.45 × 10^-4, 1.39 × 10^-4, and 1.05 × 10^-4, respectively) shown the probable risk for all oils. Moreover, hood switching reduced the risk by about 11-81%.

Extraction and determination of organic/inorganic pollutants in the ambient air of two cities located in metropolis of Tehran

In the present study, PM_2.5, volatile organic compounds (VOC), heavy metals, and polycyclic aromatic hydrocarbons (PAHs)-bonded PM_2.5 as well as asbestos fibers were investigated in two cities in the east of Tehran, Iran. To this end, 72 samples were collected from six stations located in the cities of Varamin and Pakdasht from March 2018 to March 2019. The concentration of BTEX compounds, PAHs, and heavy metals were measured using gas chromatography-flame ionization detector (GC-FID), gas chromatography-mass spectrometry (GC-Mas), and inductively coupled plasma atomic emission spectroscopy (ICP-OES), respectively. In addition, phase contrast microscopy (PCM) method was used to identify the properties of asbestos fibers. The results obtained from the present showed that the mean concentrations of PM_2.5, heavy metals, PAHs, BTEX, and asbestos fibers were 52.05 µg/m³, 319.08 ng/m³, 3.97 ng/m³, 40.58 µg/m³, and 2.84 f/L, respectively. In addition, the results obtained from PCA and heavy metals sources showed that transport fleets were the natural source of most of these pollutants. In case of PAH sources, transport and incineration of coal had the highest contribution in the emission. Furthermore, the risk assessment showed that most of the compounds have a higher risk value than the guideline value spatial distribution and also showed that stations close to airports, city terminals, and highways were more polluted than other parts of the city. Therefore, in order to have healthy air and with the least pollution, it seems necessary to formulate the necessary strategies in the cities of Varamin and Pakdasht.

Investigation of the Presence Volatile Organic Compounds (BTEX) in the Ambient Air and Biogases Produced by a Shiraz Landfill in Southern Iran

The generation and emission of volatile organic compounds (VOCs) affects the environment and air quality, playing an important role in global warming, depletion of atmospheric ozone and emission of unpleasant odors, but also directly affect human health. This study investigated the health risks of benzene, toluene, ethylbenzene, xylene (BTEX) compounds and biogas released in and around the municipal landfill. Sampling of the VOCs was carried out by the 1501NIOSH method from 8 points over 5 months. The samples were analyzed for BTEX in the ambient air of the landfill, resulting in 0.03–18.09 ppm concentrations, while for biogases a 0.08–25.2 ppm range was found. Assessment of definite health and potential risks showed that the lifetime cancer risk (LCR) for benzene and hazard quotient (HQ) for the BTEX components in all studied sampling sites are higher than the acceptable standard. The high concentration of benzene measured in ambient air indicated that petroleum compounds containing benzene and its derivatives have the highest value in the category of BTEX compounds among all emissions. Therefore, high concentrations of volatile compounds derived from VOCs, especially benzene, should be reduced at the site with control engineering measures.

External Exposure to BTEX, Internal Biomarker Response, and Health Risk Assessment of Nonoccupational Populations near a Coking Plant in Southwest China

Benzene, toluene, ethylbenzene and xylene isomers (BTEX) have raised increasing concern due to their adverse effects on human health. In this study, a coking factory and four communities nearby were selected as the research area. Atmospheric BTEX samples were collected and determined by a preconcentrator GC-MS method. Four biomarkers in the morning urine samples of 174 participants from the communities were measured by LC-MS. The health risks of BTEX exposure via inhalation were estimated. This study aimed to investigate the influence of external BTEX exposure on the internal biomarker levels and quantitatively evaluate the health risk of populations near the coking industry. The results showed that the average total BTEX concentration in residential area was 7.17 ± 7.24 μg m^-3. Trans,trans-muconic acid (T,T-MA) was the urinary biomarker with the greatest average level (127 ± 285 μg g^-1 crt). Similar spatial trends can be observed between atmospheric benzene concentration and internal biomarker levels. The mean values of the LCR for male and female residents were 2.15 × 10^-5 and 2.05 × 10^-5, respectively. The results of the risk assessment indicated that special attention was required for the non-occupational residents around the area.

Reduction in VOC emissions by intermittent aeration in bioreactor landfills with gas-water joint regulation

Landfill mining and reclamation is a new strategy for addressing the lack of space available for new landfills and realizing the sustainable development of landfills. A gas-water joint bioreactor landfill is regulated by injecting water and/or recirculating leachate, and a blasting aeration system to optimize waste stabilization. In this study, four landfill reactors were constructed to investigate the effects of ventilation methods, including continuous (20 h d^-1) and intermittent aeration (4 h d^-1 in continuous or 2-h aeration per 12 h, twice a day), on the degradation of organic matter and volatile organic compound (VOC) emissions in comparison with traditional landfills. A total of 62 VOCs were detected in the landfill reactors. Among them, halogenated compounds had the highest abundance (39.8-65.4 %), followed by oxygenated compounds, alkanes and alkenes, and aromatic compounds. Both intermittent and continuous aeration could accelerate the degradation of landfilled waste and increase the volatilization rate of VOCs. Compared with intermittent aeration, the degradation of landfilled waste was more quickly in the landfill reactor with continuous aeration. However, intermittent aeration could create anaerobic-anoxic-aerobic conditions, which were conducive to the growth and metabolism of anaerobic and aerobic microorganisms in landfills and thereby reduced more than 63.4 % of total VOC emissions from the landfill reactor with continuous aeration. Moreover, intermittent aeration could reduce the ventilation rate and decrease the cost of aeration by 80 % relative to continuous aeration. Firmicutes, Bacteroidetes, Proteobacteria and Tenericutes predominated in the landfill reactors. The environmental variables including organic matter and VOCs concentrations had significant influences on microbial community structure in the landfilled waste. These findings indicated that intermittent aeration was an effective way to accelerate the stabilization of landfilled waste and reduce the cost and environmental risks in bioreactor landfills with gas-water joint regulation.

Importance of meteorology and chemistry in determining air pollutant levels during COVID-19 lockdown in Indian cities

Indian cities can experience severe air pollution, and the reduction in activity during the first national COVID-19 lockdown (2020) offered a natural experiment to study the contribution of local sources. The current work aimed to quantify the changes due to the lockdown in NO_x, O₃ and PM_2.5 in two contrasting cities in India (Delhi and Hyderabad) using a boosted regression tree model to account for the influence of meteorology. The median NO_x and PM_2.5 concentrations were observed to decrease after lockdown in both cities, up to 57% and 75% for PM_2.5 and NO_x, respectively when compared to previous years. After normalization due to meteorology the calculated reduction after lockdown for PM_2.5 was small (<8%) in both cities, and was likely less attributable to changes in local emissions, but rather due changes in background levels (i.e. regional source(s)). The reduction of NO_x due to lockdown varied by site (on average 5-30%), likely reflecting differences in relative proximity of local sources to the monitoring site, demonstrating the key influence of meteorology on ambient levels post-lockdown. Ozone was observed to increase after lockdown at both sites in Delhi, likely due to changes in relative amounts of precursor concentrations promoting ozone production, suggesting a volatile organic compound (VOC)-limited regime in Delhi. Thus, the calculated reduction in air pollutants due to lockdown in the current work cannot be extrapolated to be solely from a reduction in emissions and instead reflects the overall change in ambient levels, as meteorology and atmospheric chemical processes also contributed.

Simultaneous annihilation of microorganisms and volatile organic compounds from municipal solid waste storage rooms with slightly acidic electrolyzed water

Great deal pathogenic bacteria and malodorous gases are hidden in municipal solid waste (MSW), which poses excellent environmental sanitation risks for sanitation workers and residents, and preventive measures should be implemented. In this study, the simultaneous annihilation of microorganisms and volatile organic compounds (VOCs) with slightly acidic electrolyzed water (SAEW) was investigated in an MSW storage room of a residential community in Shanghai, China. The microbial population of airborne, surfaces and handles of waste bins, hands of sanitation workers and the main components of VOCs were measured. The results indicated that the bacterial reduction efficiencies of SAEW with an available chlorine concentration (ACC) of 50-100 mg/L on surfaces and handles of waste bins and sanitation workers' hands were 22.7%-84.1%. Also, SAEW effectively reduced the average population of airborne bacteria and fungi by 358 and 378 colony-forming units (CFU)/m³ and decreased the detection rates of coliforms by 14.2%-51.9%. The concentrations of most VOCs were reduced by 21.4%-88.3% after spraying SAEW. And the accumulated values of carcinogenic and noncarcinogenic risks also tended to decrease with spraying SAEW. These findings imply that SAEW has significant application potential to control environmental sanitation risks in MSW storage rooms.

Comprehensive study on impact assessment of lockdown on overall ambient air quality amid COVID-19 in Delhi and its NCR, India

Indian government announced the complete lockdown from 25 March, 2020 for all outdoor activities across the country due to containment of COVID-19. This study is an attempt to assess the impacts of lockdown on ambient air quality in five cities of Indian National Capital Region including Delhi, Gurugram, Noida, Ghaziabad and Faridabad. In this context, the data of air pollutants (PM₁₀, PM_2.5, NOx, NO, NO₂, SO₂, NH₃, SO₂, CO, and C₆H₆) from 36 locations of the study area were analyzed from 1^st March to 1^st May, 2020. The results showed that PM₁₀ and PM_2.5 level decreased upto 55-65 %. NOx and NO have shown maximum reduction (∼ 50-78 %). Similarly, consistent and significant reduction in other air pollutants such as SO₂ (∼33 %), CO (∼45 %), NH₃ (∼27 %) and C₆H₆ (∼53 %) has been observed. During lockdown Air Quality Index (AQI) shows improvement as its value significantly decreased (∼ 45 %-68 %). An interesting feature observed that during first week of lockdown O₃ decreased but later it increased by ∼19-27%. The study suggests that this pandemic gives lessons for interventions for urban air pollution mitigation in controlling the health impact due to urban air pollution.

Level of air BTEX in urban, rural and industrial regions of Bandar Abbas, Iran; indoor-outdoor relationships and probabilistic health risk assessment

This study focused on the measurement of BTEX (benzene, toluene, ethylbenzene and xylene) concentrations in the air of various regions and indoor-outdoor environments in Bandar Abbas, Iran. Air samples were taken actively and analyzed by gas chromatography-mass spectrometry (GC-MS) during two one-month periods i.e., Feb 2020 (period I) and Sep/Oct 2020 (period II). The mean air temperature and the levels of all BTEX compounds were higher in period II. The highest total BTEX (t-BTEX) levels (median [min-max]) were found in the urban region (18.00 [5.21-67.24] μg m^-3), followed by industrial region (7.00 [2.05-14.76] μg m^-3) and rural region (2.81 [ND-7.38] μg m^-3). The significant positive correlations between all BTEX compounds and T/B ratio >1 indicated the vehicular traffic as the main source of emission. At 95th percentile probability, the non-cancer risk of t-BTEX in urban region was only less than one order of magnitude below the threshold level of unity (1.91E-01) and the cancer risk of benzene exceeded the recommended level of 1.0E-06 by U.S. EPA in urban (7.69E-06) and industrial (2.97E-06) regions. It was found that the indoor/outdoor ratio of BTEX concentration in beauty salon and hospital was greater than 1. Overall, the current levels of BTEX in the ambient air of study area, especially near urban roadside and in some indoor environments, should not be overlooked and appropriate mitigation actions should be undertaken.

Species and characteristics of volatile organic compounds emitted from an auto-repair painting workshop

Volatile organic compounds (VOCs) are secondary pollutant precursors having adverse impacts on the environment and human health. Although VOC emissions, their sources, and impacts have been investigated, the focus has been on large-scale industrial sources or indoor environments; studies on relatively small-scale enterprises (e.g., auto-repair workshops) are lacking. Here, we performed field VOC measurements for an auto-repair painting facility in Korea and analyzed the characteristics of VOCs emitted from the main painting workshop (top coat). The total VOC concentration was 5069-8058 ppb, and 24-35 species were detected. The VOCs were mainly identified as butyl acetate, toluene, ethylbenzene, and xylene compounds. VOC characteristics differed depending on the paint type. Butyl acetate had the highest concentration in both water- and oil-based paints; however, its concentration and proportion were higher in the former (3256 ppb, 65.5%) than in the latter (2449 ppb, 31.1%). Comparing VOC concentration before and after passing through adsorption systems, concentrations of most VOCs were lower at the outlets than the inlets of the adsorption systems, but were found to be high at the outlets in some workshops. These results provide a theoretical basis for developing effective VOC control systems and managing VOC emissions from auto-repair painting workshops.

Influence of the seasonality and of urban variables in the BTEX and PM2.5 atmospheric levels and risks to human health in a tropical coastal city (Fortaleza, CE, Brazil)

The International Agency for Research on Cancer (IARC) classifies benzene in group 1 (carcinogenic to humans). Particulate matter (PM) has recently also been classified in this category. This was an advance toward prioritizing the monitoring of particles in urban areas. The aim of the present study was to assess levels of PM_2.5 and BTEX (benzene, toluene, ethylbenzene, and xylene), the influence of meteorological variables, the planetary boundary layer (PBL), and urban variables as well as risks to human health in the city of Fortaleza, Brazil, in the wet and dry periods. BTEX compounds were sampled using the 1501 method of NIOSH and determined by GC-HS-PID/FID. PM_2.5 was monitored using an air sampling pump with a filter holder and determined by the gravimetric method. Average concentrations of BTEX ranged from 1.6 to 45.5 μg m^-3, with higher values in the wet period, which may be explained by the fact that annual distribution is influenced by meteorological variables and the PBL. PM_2.5 levels ranged from 4.12 to 33.0 μg m^-3 and 4.18 to 86.58 μg m^-3 in the dry and wet periods, respectively. No seasonal pattern was found for PM_2.5, probably due to the influence of meteorological variables, the PBL, and urban variables. Cancer risk ranged from 2.46E^-04 to 4.71E^-03 and 1.72E^-04 to 2.01E^-03 for benzene and from 3.07E^-06 to 7.04E^-05 and 3.08E^-06 to 2.85E^-05 for PM_2.5 in the wet and dry periods, respectively. Cancer risk values for benzene were above the acceptable limit established by the international regulatory agency in both the dry and wet periods. The results obtained of the noncarcinogenic risks for the compounds toluene, ethylbenzene, and xylene were within the limits of acceptability. The findings also showed that the risk related to PM is always greater among smokers than nonsmokers.

Spatial distribution and health risk of exposure to BTEX in urban area: a comparison study of different land-use types and traffic volumes

Many previous studies have investigated BTEX concentrations in urban areas; however, the available evidence on the association of different land-use types and BTEX concentrations is still scarce. In this study, the BTEX concentrations were measured and compared in different land-use types and traffic volumes of Mashhad metropolis, Iran. Sampling was conducted in summer and winter of 2018 based on NIOSH 1501 method in six land-use types, including Residential, Commercial/official, Industrial, Greenspace, Transportation, and Tourism. The spatial autocorrelation model was used to investigate the emission pattern. The Monte Carlo simulation technique and sensitivity analysis were used to assess the health risk of exposure to BTEX compounds. The median [interquartile range (IQR)] of benzene, toluene, ethylbenzene m-xylene, o-xylene and total BTEX concentrations based on overall mean were 4 (2.23), 8.37 (4.48), 1.2 (1.46), 0.89 (2.59), 0.8 (1.73) and 17.7 (8.19) µg/m³, respectively. Benzene and toluene had clustered emission patterns (z-score > 1.96). Exposure to benzene in the study area had a carcinogenic risk for inhabitants. The concentration of BTEX compounds was significantly different based on land-use type. The maximum and minimum concentrations of BTEX were observed in Transportation and Greenspace land uses, respectively. The BTEX concentrations in summer were significantly higher than in winter, and traffic had a significant effect on BTEX concentrations. Overall, our results supported a significant relationship between land-use type and BTEX concentrations in the urban area. Moreover, ambient benzene concentration had a carcinogenic risk potential for inhabitants of study area.

Exposure characteristics and risk assessment of VOCs from Chinese residential cooking

In comparison with various restaurant cuisines, common cooking methods are more represented in residential cooking. Rather than the exhaust pipe or the ambient environment in the cooking room, the respiration zone better reflects the health risks for operators. In this study, the concentrations of total volatile organic compound (TVOC) released from six typical cooking methods were monitored online in the respiratory zone, and the VOCs were analysed by GC-MS. The results demonstrated that the intensities of exposure to TVOC for the different cooking methods decreased as follows: stir-frying (3.809 mg/m³) > quick-frying (2.724 mg/m³) > deep-frying (2.465 mg/m³) > boiling (1.161 mg/m³)≈stewing (1.149 mg/m³) > limit in China (0.600 mg/m³) > steaming (0.440 mg/m³). The intense ventilation mode of the ventilator reduced exposure to TVOC by 45-63% relative to the medium mode. Eleven types of VOCs (approximately 200 compounds) were found in Chinese residential cooking fumes, and the predominant contaminants were aldehydes, followed by alkanes, unsaturated aldehydes, alcohols and alkenes. The mass percentage of aromatic hydrocarbons in all VOCs emitted from Chinese residential cooking was only 1%, while the value was 17-48% for commercial restaurants. The results of a health risk assessment revealed that the total potential carcinogenic risk level for VOCs released by six residential cooking methods decreased as follows: deep-frying (5.75) > stir-frying (3.95) > quick-frying (2.94) > stewing (1.99) > boiling (1.73) > steaming (1.48). Chinese residential cooking, and especially deep frying, has potential health impacts for the operator.

Occurrence, spatial distribution, seasonal variations, potential sources, and inhalation-based health risk assessment of organic/inorganic pollutants in ambient air of Tehran

The present study evaluated the concentrations, spatial distribution, seasonal variations, potential sources, and risk assessment of organic/inorganic pollutants in ambient air of Tehran city. Totally, 180 air samples were taken from 9 sampling stations from March 2018 to March 2019 and were analyzed to determine the concentrations of organic pollutants (BTEX compounds and PM_2.5-bound PAHs) plus inorganic pollutants (PM_2.5-bound metals and asbestos fibers). The results revealed that the mean concentrations of ∑ PAHs, BTEX, ∑ heavy metals, and asbestos fibers were 5.34 ng/m³, 60.55 µg/m³, 8585.12 ng/m³, and 4.13 fiber/ml in the cold season, respectively, and 3.88 ng/m³, 33.86 µg/m³, 5682.61 ng/m³, and 3.21 fiber/ml in the warm season, respectively. Source apportionment of emission of the air pollutants showed that PAHs are emitted from diesel vehicles and industrial activities. BTEX and asbestos are also released mainly by vehicles. The results of the inhalation-based risk assessment indicated that the carcinogenic risk of PAHs, BTEX, and asbestos exceeded the recommended limit by The US environmental protection agency (US EPA) and WHO (1 × 10^-4). The risk of carcinogenesis of heavy metal of lead and chromium also exceeded the recommended limit. Thus, proper management strategies are required to control the concentration of these pollutants in Tehran's ambient air in order to maintain the health of Tehran's citizens.

A wavelet-based random forest approach for indoor BTEX spatiotemporal modeling and health risk assessment

This study reports on BTEX concentrations in one of the largest parking garages in Iran with a peak traffic flow reaching up to ~9300 vehicles in the last few days of the Nowruz holidays. Samples were obtained on different days of the week at three main locations in the Zaer Parking Garage. A novel wavelet-based random forest model (WRF) was trained to estimate BTEX concentrations by decomposing temperature, day of the week, sampling location, and relative humidity data with a maximal overlap discrete wavelet transform (MODWT) function and subsequently inputted into the WRF model. The results suggested that the WRF model can reasonably estimate BTEX trends and variations based on high R2 values of 0.96, 0.95, and 0.98 for training, validation, and test data subsets, respectively. The carcinogenic (LTCR) and non-carcinogenic health risk (HI) assessment results indicated a definite carcinogenic risk of benzene (LTCR = 2.22 × 10-4) and high non-carcinogenic risk (HI = 4.51) of BTEX emissions. The results of this study point to the importance of BTEX accumulation in poorly ventilated areas and the utility of machine learning in forecasting air pollution in diverse airsheds such as parking garages.

COVID-19 lockdown: Effects on selected volatile organic compound (VOC) emissions over the major Indian metro cities

Due to the COVID-19 pandemic, many countries across the world, including India, have imposed nationwide lockdowns to contain the spread of the virus. Many studies reported that the air quality had improved much due to the lockdown. This study examines the variation of Volatile Organic Compounds (VOCs) over the Indian metropolitan cities during the lockdown period by using ground-based and satellite observations. Ground-based BTEX (Benzene, Toluene, Ethylbenzene, and Xylenes) measurements from various metropolitan cities have shown a drastic drop of about 82% in the first phase of lockdown when compared with the pre-lockdown period. Whereas the spatial distribution of formaldehyde (HCHO), obtained from the TROPOspheric Monitoring Instrument (TROPOMI) onboard Sentinal-5P satellite, did not show any significant variation due to COVID-19 lockdown, indicating the major source of HCHO is biogenic or pyrogenic. The BTEX ratios were evaluated for a better understanding of the source and photochemical age of the air samples. The ozone forming potential of BTEX in all locations was found reduced; however, the corresponding decrease in ozone concentrations was not observed. The increase in ozone concentrations during the same period indicates alternative sources contributing to ozone formation.

Human, Forest and vegetation health metrics of ground-level ozone (SOMO35, AOT40f and AOT40v) in Tehran

PURPOSE

We aimed to investigate the spatial O₃ indices (SOMO35: annual sum of maximum daily 8-h ozone means over 35 ppb, AOT40: the accumulated exposure over an hourly threshold of 40 ppb during daylight hours between 8:00 and 20:00 in the growing seasons of plants) in Tehran (2019-2020).

METHODS

The data of ambient O₃ concentrations, measured at twenty-three regulatory ambient air quality monitoring stations (AQMSs) in Tehran, were obtained.

RESULTS

The annual mean O₃ concentrations were found to be 15.8-25.7 ppb; the highest and lowest annual mean concentration of ambient O₃ were observed in Shahrdari 22 and Shahr-e-Rey stations, respectively. Spatial distribution of exposure to O₃ across Tehran was in the range of 1.36-1.64; the highest O₃ concentrations were observed in the northern, west and south-western parts of Tehran, while the central and south areas of Tehran city experienced low to moderate concentrations. The indices of SOMO35, AOT40f and AOT40v across AQMSs in Tehran was in the range of 1830-6437 ppb. Days, 10,613-39,505 ppb.h and 4979-16,804 ppb.h, respectively. For Tehran city, the indices of SOMO35 and AOT40f were 4138 ppb. days and 27,556 ppb.h respectively. Our results revealed that the value of SOMO35 across AQMSs of Tehran was higher than the recommended target value of 3000 ppb. days.

CONCLUSIONS

To reduce O₃ pollution and its effects on both human and plants health, the governmental organizations should take appropriate sustainable control policies.

Characteristics of roadside volatile organic compounds in an urban area dominated by gasoline vehicles, a case study in Hanoi

Volatile organic compounds (VOCs) are important air pollution issues because of their potential health effects, and the contribution to ground ozone and secondary particulate matter. In this study, 53 VOC species near nine roads in Hanoi were monitored by sampling and analyzed by GC-FID four times per day on weekdays and in the morning on the weekend, from December 2014 to January 2015. In parallel with VOC sampling, vehicle number was counted, and meteorological conditions were recorded. A large share of motorbikes was found, accounted for 82% of overall for all period, and 88% in rush hours. The average TVOC concentration was 305.1 ppb; while those of BTEX were 12.8/27.4/4.8/15.9/6.0 ppb for benzene/toluene/ethylbenzene/m,p-xylenes/o-xylene, respectively. Isopentane was the most abundant species of VOCs. A significant carcinogenic risk of benzene species was found. Ozone formation potential (OFP) of VOCs was of 1752.7 ppb. Levels of VOC species reflected well the transportation volume. Strong correlations between motorbike number related parameters and ethylbenzene were found. High correlations were also found among ethylbenzene and almost all other VOC species. It implied that the majority of VOCs near road emitted from the same source, which is motorbikes. The calculation using emission factors from COPERT 5 model with conditions of fleets in Hanoi showed that VOCs from motorbikes contributed to more than 90% of the VOC level.

Observations of BTEX in the ambient air of Kuala Lumpur by passive sampling

Benzene, toluene, ethylbenzene and xylenes (BTEX) are well known hazardous volatile organic compounds (VOCs) due to their human health risks and photochemical effects. The main objective of this study was to estimate BTEX levels and evaluate interspecies ratios and ozone formation potentials (OFP) in the ambient air of urban Kuala Lumpur (KL) based on a passive sampling method with a Tenax® GR adsorbent tube. Analysis of BTEX was performed using a thermal desorption (TD)-gas chromatography mass spectrometer (GCMS). OFP was calculated based on the Maximum Incremental Reactivity (MIR). Results from this study showed that the average total BTEX during the sampling period was 66.06 ± 2.39 μg/m³. Toluene (27.70 ± 0.97 μg/m³) was the highest, followed by m,p-xylene (13.87 ± 0.36 μg/m³), o-xylene (11.49 ± 0.39 μg/m³), ethylbenzene (8.46 ± 0.34 μg/m³) and benzene (3.86 ± 0.31 μg/m³). The ratio of toluene to benzene (T:B) is > 7, suggesting that VOCs in the Kuala Lumpur urban environment are influenced by vehicle emissions and other anthropogenic sources. The average of ozone formation potential (OFP) value from BTEX was 278.42 ± 74.64 μg/m³ with toluene and xylenes being the major contributors to OFP. This study also indicated that the average of benzene concentration in KL was slightly lower than the European Union (EU)-recommended health limit value for benzene of 5 μg/m³ annual exposure.

Spatial analysis and risk assessment of urban BTEX compounds in Urmia, Iran

Land Use Regression models (LUR) are the most common tools to estimate intra-urban air pollutant exposure in epidemiological studies. However, number of available and published models in developing and middle up income countries is still scarce. Here, we developed seasonal and overall LUR models for the spatial distribution of benzene, toluene, ethylbenzene and xylene (BTEX) based on 20 monitoring stations and 166 potentially predictive variables (PPVs) in Urmia, Iran. Carcinogenic and non-carcinogenic risks of exposure to BTEX and its sensitivity analysis were assessed using a probabilistic approach. The mean and standard deviation (in brackets) of overall benzene, toluene, ethylbenzene and xylene were 12.83 (16.19), 27.03 (32.00), 4.72 (4.15) and 27.35 (29.36) μg/m³, respectively. In all models the R² value of LUR models of benzene, toluene, ethylbenzene, xylene and total BTEX ranged from 0.66 to 0.85, 0.61, 0.88, 0.72 to 0.94, 0.75 to 0.84 and 0.67 to 0.93. The root mean square error (RMSE) for leave-one-out cross-validations (LOOCV) for benzene, toluene, ethylbenzene and xylene ranged from 7.48 to 10.31, 23.0 to 30.0, 3.40 to 6.90, 16.27 to 24.49, 36.10-50.0 μg/m³, respectively. The estimated lifetime carcinogenic risk (LTCR) indicated that ambient concentration of benzene is at a risk level for Urmia inhabitants (LTCR >10^-6). Sensitivity analysis for LTCR model indicated that concentration of benzene (C) was the most effective variable in increasing the carcinogenic risk (correlation coefficient ranged from 0.97 to 0.98 for all models).

Understanding the sources and spatiotemporal characteristics of VOCs in the Chengdu Plain, China, through measurement and emission inventory

In order to evaluate the volatile organic compounds (VOCs) pollution characteristics in Chengdu and to identify their sources, ambient air sample collection and measurement were conducted at 28 sampling sites covering all districts/counties of Chengdu from May 2016 to January 2017. Meanwhile, a county-level anthropogenic speciated VOCs emission inventory was established by "bottom-up" method for 2016. Then, a comparison was made between the VOCs emissions, spatial variations, and source structures derived from the measurement and emission inventory. Ambient measurements showed that the annual average mixing ratios of VOCs in Chengdu were 57.54 ppbv (12.36 to 456.04 ppbv), of which mainly dominated by alkanes (38.8%) and OVOCs (22.0%). The ambient VOCs in Chengdu have distinct spatiotemporal characteristics, with a high concentration in January at the middle-northern part of the city and a low concentration in September at the southwestern part. The spatial distribution of VOCs estimated by the emission inventory was in good agreement with ambient measurements. Comparison of individual VOCs emissions indicated that the emissions of non-methane hydrocarbon species agreed within ±100% between the two methods. Both positive matrix factorization (PMF) model results and emission inventory showed that vehicle emissions were the major contributor of anthropogenic VOCs in Chengdu (31% and 37%), followed by solvent utilization (26% and 27%) and industrial processes (23% and 30%). The large discrepancies were found between the relative contribution of combustion sources, and the PMF resolved more contributions (20%) than the emission inventory (6%). Overall, this study demonstrates that measurement results and emission inventory were in a good agreement. However, to improve the reliability of the emission inventory, we suggest significant revision on source profiles of oxygenated volatile organic compounds (OVOCs) and halocarbons, as well as more detailed investigation should be made in terms of energy consumption in household.

Effect of source-classified and mixed collection from residential household waste bins on the emission characteristics of volatile organic compounds

The implementation of domestic waste classification following the principles of reduction, recycling, and harmlessness is an effective method to improve the urban and rural environments and to promote resource recycling. However, in many developing countries, the community residents lack awareness of the benefits of classified collection, which leads to a lack of initiative to classify MSW. To make the people realize the importance of MSW classification and increase the classification dynamics, Suzhou, China was taken as an example in this study, and residential areas were selected as sampling sites for classified and mixed collection of domestic waste. The main components of the odorous volatile organic compounds (VOCs) emitted from the dustbins via different disposal modes were determined by sampling in spring, summer, autumn, and winter. In addition, the ozone formation potential (OFP) and human health risk assessment of the VOCs were analyzed. Halogenated compounds were the major pollutants from the household waste dustbins of the residential areas. However, aromatic compounds contributed the most to the OFP of the VOCs. The OFP of VOCs reached the highest peak in summer, which was 1.02 × 10³ μg/m³. Furthermore, more attention needs to be paid in classifying waste to reduce the concentration of OFP. Although there was a carcinogenic risk in spring and summer, it declined after waste classification. Compared with mixed collection, the source-classified collection of garbage had advantages in terms of controlling the emission of VOCs, ozone formation potential, and human health risk. These results could provide the evidence demonstrating the advantages of waste classification and attract people's attention. Furthermore, the results can also provide impetus to those countries, where separate collection of waste has not yet been implemented, to improve the enthusiasm for classification and the integrity of waste classification system. Residents should be encouraged to classify household waste in residential areas.

The emission characteristic of VOCs and the toxicity of BTEX from different mosquito-repellent incenses

Three types of mosquito-repellent incenses including disc, electric liquid and electric mat, were selected to investigate the emission of volatile organic compounds in the respiratory zone during the burning. VOCs were analyzed by GC-MS. Results showed that the average concentration of TVOCs released by using the disc, electric liquid and electric mat mosquito repellent incense types were 7.760 ± 4.724, 3.122 ± 0.866 and 1.192 ± 0.062 mg/m³, respectively. The TVOCs pollution level produced during the burning of different mosquito-repellent incense types was ranked in the order: disc > electric liquid > electric mat. The concentration of TVOCs produced by Q-liquid, L-liquid, Q-disc and L-disc mosquito-repellent incense types could cause discomfort to the human body. Other types of mosquito-repellent incense induced multiple synergistic effects on human response. About 230 kinds of VOCs including 14 types of VOCs, were found in the smoke of mosquito-repellent incense. The number and content of alkanes was the highest, followed by aromatic hydrocarbons and esters. The level of non-carcinogenic health risk presented by exposure to BTEX (toluene, xylene and ethylbenzene) was acceptable. The chronic daily intake of VOCs decreased with age for both males and females, with male exposure being higher than that of the female, except for children.

Health Risk Assessment of the Levels of BTEX in Ambient Air of One Urban Site Located in Leon, Guanajuato, Mexico during Two Climatic Seasons

Levels of BTEX (benzene, toluene, ethylbenzene, and p-xylene) were determined in ambient air of an urban site located at the center of Mexico (Leon City in Guanajuato State) during two climatic seasons of 2018 (summer and autumn). Ethylbenzene (11.86 µg m−3) and toluene (11.85 µg m−3) showed the highest median concentrations during the study period. BTEX concentrations did not show a diurnal pattern but a seasonal trend was observed for benzene and toluene at a significant level of α = 0.05. Bi-variate and multivariate analysis showed significant positive correlations (at α = 0.05) among BTEX (excepting benzene), indicating common sources for toluene, ethylbenzene, and p-xylene and a different origin for benzene. A meteorological study was also conducted in order to determine the origin of air masses that could influence the BTEX concentrations in the study site. Finally, it was found that all BTEX species presented hazard quotient values (HQs) <1, indicating that there is no risk of non-cancer during the studied period. Lifetime cancer risk due to benzene exposure for the adult and child populations studied were estimated to be 7 in 1,000,000 and 1 in 100,000, respectively.

Spatiotemporal variations and characterization of the chronic cancer risk associated with benzene exposure

A spatiotemporal analysis of benzene was performed in east of the USA and in a representative station in Baltimore County, in order to assess its trend over a 25-year time span between 1993 and 2018. A novel time series analysis technique known as TBATS (an ensemble of Trigonometric seasonal models, Box-Cox transformation, ARMA error plus Trend and Seasonal components) was applied for the first time on an air contaminant. The results demonstrated an annual seasonality and a continuously declining trend in this respect. The success of Reformulated Gasoline Program (RFG), initiated in 1995, was obviously detected in time series data since the daily benzene concentrations reduced to one-sixth of its original level in 1995. In this regard, the respective values of mean absolute scaled error (MASE) were 0.35 and 0.45 for training and test series. Given the observed concentrations of benzene, the hot spot areas in east of the US were identified by spatial analysis, as well. A chronic cancer risk was followed along the study area, by both a deterministic and probabilistic risk assessment (PRA) techniques. It was indicated that children are at higher risk than that of adults. The range of estimated risk values for PRA was higher and varied between 6.45 × 10^-6 and 1.68 × 10^-4 for adults and between 8.13 × 10^-6 and 8.29 × 10^-4 for children. According to the findings of PRA, and referring to the threshold level of 1 × 10^-4, only 1.2% of the adults and 28.77% of the children were categorized in an immediate risk group.

Temporal variations of atmospheric benzene and its health effects in Tehran megacity (2010-2013)

The main aims of the present research were (1) investigation of the temporal trends of atmospheric benzene concentrations in Tehran city during the period 2010 to 2013 and (2) assessment of carcinogenic and non-carcinogenic health risks of inhalation exposure to benzene. For the first objective, the data of ambient air benzene concentrations were derived from 15 air quality monitoring stations (AQMSs) in Tehran during the years 2010 to 2013 and they were temporally investigated after data cleaning and missing data imputation. The excess lifetime cancer risk (ELCR) and hazard quotient (HQ) were estimated to reveal the carcinogenic and non-carcinogenic health effects of exposure to ambient benzene. Our findings indicated that over 2010-2013, annual mean concentrations of benzene were in the range of 1.84 to 2.57 μg m^-3, and the highest annual mean concentration was observed in 2011 with a mean of 2.57 μg m^-3. The four-year average concentration of benzene during the period from 2010 to 2013 was 2.14 μg m^-3. Furthermore, the HQ for inhalation exposure to ambient benzene was lower than the acceptable risk level (HQ < 1) over the study time period which indicated that the non-carcinogenic effects are very unlikely to happen. In addition, health risk assessment for ELCR showed that the potential cancer risk for inhalation exposure to benzene was 1.67 × 10^-5 over the study period, which is significantly higher than the limits recommended by the U.S. EPA (1 × 10^-6). Our study clearly proves that the ambient benzene concentration in Tehran has substantially higher carcinogenic effects on the population. Appropriate sustainable control measures should be taken to reduce air benzene concentration and protect public health.