Removal of emerging contaminants (bisphenol A and antibiotics) from kitchen wastewater by alkali-modified biochar

Gradient purification of surface water and ultrafiltration membrane fouling mitigation based on Fe(VI) multifunctional integration characteristics: Is a sedimentation unit necessary?

Ferrate (Fe(VI)) can provide oxidation and in-situ coagulation/adsorption for the removal of emerging contaminants and natural organic matter, and can be used in conjunction with ultrafiltration (UF) membrane to enhance the removal of composite contaminants and mitigate UF membrane fouling. Based on the Fe(VI) multifunctional integration characteristics, the study objectively and comprehensively verified the gradient purification of surface water and the UF membrane fouling mitigation by Fe(VI)-UF and sulfite (S(IV)) activated Fe(VI) (S(IV)/Fe(VI))-UF, elucidated the effect of sedimentation unit on the UF mechanism and the membrane fouling behaviors, and revealed the free energy changes throughout the UF process. The experimental results demonstrated that S(IV)/Fe(VI)-UF showed superior purification performance and UF membrane fouling mitigation than Fe(VI)-UF. S(IV)/Fe(VI)-UF achieved removals of sulfamethoxazole, DOC, and UV254 up to 77.73 %, 61.86 %, and 86.33 %, and was able to significantly mitigate UF membrane fouling by prolonging the transition stage and positively shifting the interfacial free energy. Innovatively, the absence of a sedimentation unit was found to adversely affect the initial stages of Fe(VI)-UF and S(IV)/Fe(VI)-UF by lowering the energy barriers, while negligibly affecting cake filtration. Additionally, the water treatment cost of S(IV)/Fe(VI) was 0.3 yuan per ton, indicating notable economic benefits and engineering potential. While deepening the understanding of Fe(VI) multifunctional integration characteristics, the above results provided theoretical and data support for S(IV)/Fe(VI)-UF and Fe(VI)-UF treatment of surface water, and enriched the application scenarios of Fe(VI)-related technologies.

A facile approach to lignin-based biochar derived from black liquor and the study of its removal to tetracycline from water

The present study focuses on preparing lignin-biochar (L-Bio) from papermaking black liquor-lignin and the study its effectiveness and mechanism in removing tetracycline (TC) from water. Results showed that the yield, BET surface area and pore size of L-Bio were 36.3707-40.2567 %, 392.2232-625.3296 m2•g-1 and 2.244-1261.915 μm, respectively. Adsorption experiment results showed that Bio-800 °C has the maximum adsorption capacity of 243.9067 mg•g-1 and it has the best removal effect on TC under neutral conditions. Adsorption kinetics results showed that the quasi second-order kinetic equation can reflect the process better, which indicates that the adsorption process is mainly chemical adsorption. The possible mechanism was proposed. It mainly includes pore filling, ion exchange, electrostatic interaction, hydrogen bonding, etc. The objectives of the study were to (1) provide a new approach for the resource utilization of lignin and achieve waste to waste conversion; (2) analysis the relationship between the structure and properties of L-Bio and propose its possible mechanism for removing TC from water, which can provide theoretical support for L-Bio's practical application.

Tailoring the synergistic effect of integrated polypyrrole hydrogel on the adsorption activity of rice husk-based activated carbon (polypyrrole/activated carbon composite) for bisphenol-A and 4-chlorophenol: experimental and theoretical analysis

Rice husk-derived activated carbon was hybridized with polypyrrole hydrogel (Pyh), producing advanced nanocomposite (Pyh/AC). The composite was applied as an enhanced adsorbent for two forms of toxic phenolic compounds, particularly bisphenol-A (BSP-A) and 4-chlorophenol (4-CL). The adsorption studies were evaluated considering the synthetic effect of Pyh based on the criteria of statistical physics equilibrium modeling. The reported saturation adsorption capacities for BSP-A and 4-CL using Pyh/AC are 321.4 mg/g and 365.8 mg/g, respectively. These values are significantly higher than the estimated values for the hydrogel in separated form. The analysis of the steric properties validated the saturation of the composite with about 169.7 mg/g and 119.5 mg/g as active site density during the uptake of BSP-A and 4-CL, respectively. These values are higher than the estimated densities using Pyh (110.5 mg/g (BSP-A) and 99.3 mg/g (4-CL)), demonstrating the positive impact of the hybridization process in terms of surface area, porosity, and incorporated chemical functional groups. Furthermore, the capacity of each site on the structure of Pyh/AC to accommodate up to 3 molecules of BSP-A and 6 molecules of 4-CL displays the operation of multi-molecular mechanisms and the ordering of these adsorbed molecules vertically and in non-parallel forms. The adsorption energies, either based on classic (<21 kJ/mol) or advanced (<20 kJ/mol) isotherm studies, reflect the physisorption of the phenolic compounds on the surface of Pyh/AC. The composite also shows thermodynamically stable properties and the uptake reactions that occurred with exothermic, favorable, and spontaneous properties.

Biochar for mitigating pharmaceutical pollution in wastewater: A sustainable solution

Pharmaceutical contaminants (PCs), including antibiotics, analgesics, and other medications, pose a growing threat to aquatic ecosystems and human health due to their persistence and bioaccumulation potential. Biochar, a carbonaceous material derived from biomass pyrolysis, has emerged as a sustainable adsorbent for removing PCs from wastewater. Biochar is reported to remove PCs from water with an average range of 58 to 91 %, depending on the nature of feedstock, pyrolysis conditions, and characteristics of the pharmaceuticals. Biochar's effectiveness is attributed to its unique properties, including high porosity, large surface area and diverse functional groups, which enable the adsorption of various pharmaceutical compounds through physical and chemical interactions. Common PCs such as tetracycline, ciprofloxacin, ibuprofen, paracetamol, sulfamethoxazole, and cephalexin can be effectively removed using biochar. The adsorption process involves different mechanisms such as Van der Waals forces, electrostatic interactions, hydrogen bonding, and surface complexation. This review summarizes the current state of knowledge on biochar-based adsorption mechanisms, highlights successful applications in wastewater treatment, and identifies areas for future research. While promising, a deeper understanding of adsorption mechanisms, optimization of biochar production, and the development of effective regeneration methods are crucial for maximizing biochar's efficacy and ensuring its sustainable implementation in wastewater treatment systems.

Removal of active pharmaceutical compounds in Primalan and Diane using pumpkin biochar: synthesis, characterization, and adsorption study

This investigation aims to apply the adsorption process to eliminate mequitazine and ethinylestradiol, the active molecules of Primalan and Diane, respectively, from aqueous solutions, utilizing biochar synthesized from pumpkin fruits (PB-500). The results revealed that the obtained adsorbent possessed a notable specific surface area, contributing to removal efficiencies of 66.61% and 62.37% for mequitazine and ethinylestradiol, respectively. The sludge recovered under equilibrium conditions was also characterized to facilitate comparison of biochar properties before and after adsorption. Several models were employed to analyze the adsorption kinetics and isotherms, showing that the pseudo-second-order model offers the optimal representation for the kinetic behavior. Both the Sips and Freundlich models accurately described the isotherm data. On the other hand, the adsorption on PB-500 was clearly affected by the variation in solution pH. The PB-500 variation test indicated that the optimum adsorbent concentration was around 0.8 g L-1, where the removal yields were 67% for mequitazine and 65.16% for ethinylestradiol. Thermodynamic studies indicated that the adsorption was exothermic for both pollutants. Consequently, it can be inferred that pumpkin-biochar serves as an effective adsorbent for eliminating mequitazine and ethinylestradiol from water.

Pyrolytic conversion of cattle manure and acid mine drainage sludge into biochar for oxidative and adsorptive removal of the antibiotic nitrofurantoin

Antibiotics in aquatic environments can foster the development of antibiotic-resistant bacteria, posing significant risks to both living organisms and ecosystems. This study explored the thermo-chemical conversion of cattle manure (CM) into biochar and assessed its potential as an environmental medium for removing nitrofurantoin (NFT) from water. The biochar was produced through the co-pyrolysis of CM and acid mine drainage sludge (AMDS) in a N2 condition. The gaseous and liquid products generated during pyrolysis were quantified and characterized. The biochar exhibited both catalytic and adsorptive capability in NFT removal. It effectively activated persulfate to drive oxidative degradation of NFT via radical (SO4•- and •OH) and non-radical (1O2) pathways. NFT adsorption on the biochar involved multiple binding mechanisms, including electrostatic, hydrogen bonds, and π-π EDA interactions, as evidenced by XPS analysis before and after the reaction. Furthermore, the biochar's performance stability was demonstrated through five cycles of reuse and leaching tests. These findings present a viable approach to generate energy from waste by co-pyrolyzing of livestock manure and metal-containing industrial waste, while also producing environmental media capable of removing antibiotics from wastewater through diverse mechanisms.

Advances of carbon-based materials for activating peracetic acid in advanced oxidation processes: A review

In recent years, the peracetic acid (PAA)-based advanced oxidation process (AOPs) has garnered significant attention in the field of water treatment due to rapid response time and environmentally-friendliness. The activation of PAA systems by diverse carbon-based materials plays a crucial role in addressing emerging environmental contaminants, including various types, structures, and modified forms of carbon materials. However, the structural characteristics and structure-activity relationship of carbon-based materials in the activation of PAA are intricate, while the degradation pathways and dominant active species exhibit diversity. Therefore, it is imperative to elucidate the developmental process of the carbon-based materials/PAA system through resource integration and logical categorization, thereby indicating potential avenues for future research. The present paper comprehensively reviews the structural characteristics and action mechanism of carbon-based materials in PAA system, while also analyzing the development, properties, and activation mechanism of heteroatom-doped carbon-based materials in this system. In conclusion, this study has effectively organized the resources pertaining to prominent research direction of comprehensive remediation of environmental water pollution, thereby elucidating the underlying logic and thought process. Consequently, it establishes robust theoretical foundation for future investigations and applications involving carbon-based materials/PAA system.

Emerging hazardous chemicals and biological pollutants in Canadian aquatic systems and remediation approaches: A comprehensive status report

Emerging contaminants can be natural or synthetic materials, as well as materials of a chemical, or biological origin; these materials are typically not controlled or monitored in the environment. Canada is home to nearly 7 % of the world's renewable water supply and a wide range of different kinds of water systems, including the Great Lake, rivers, canals, gulfs, and estuaries. Although the majority of these pollutants are present in trace amounts (μg/L - ng/L concentrations), several studies have reported their detrimental impact on both human health and the biota. In Canadian aquatic environments, concentrations of pharmaceuticals (as high as 115 μg/L), pesticides (as high as 1.95 μg/L), bioavailable heavy metals like dissolved mercury (as high as 135 ng/L), and hydrocarbon/crude oil spills (as high as 4.5 million liters) have been documented. Biological threats such as genetic materials of the contagious SARS-CoV-2 virus have been reported in the provinces of Québec, Ontario, Saskatchewan and Manitoba provinces, as well as in the Nunavut territory, with a need for more holistic research. These toxins and emerging pollutants are associated with nefarious short and long-term health effects, with the potential for bioaccumulation in the environment. Hence, this Canadian-focused report provides the footprints for water and environmental sustainability, in light of this emerging threat to the environment and society. Several remediation pathways/tools that have been explored by Canadian researchers, existing challenges and prospects are also discussed. The review concludes with preventive measures and strategies for managing the inventory of emerging contaminants in the environment.

Improved engineered fungal-bacterial commensal consortia simultaneously degrade multiantibiotics and biotransform food waste into lipopeptides

Resource utilization of food waste is necessary to reduce environmental pollution. However, antibiotics can enter the environment through food waste, resulting in antibiotic residues, which pose potential risks to human health. In this study, commensal artificial consortia were constructed through intercellular adaptation to simultaneously degrade antibiotics and bioconvert food waste into lipopeptides. The biodegradation efficiency of oxytetracycline in the three-strain consortium, which contained lipopeptide-producing Bacillus amyloliquefaciens HM618, high-level proline-producing Corynebacterium glutamate, and laccase-producing Pichia pastoris, was around 100% in the food waste medium at 72 h; this was higher than that in the pure culture of P. pastoris-Lac. Sulfamethoxazole could be removed at 48 h. However, the lipopeptide level in the three-strain consortium was only 77 mg/L. The four-strain consortium containing free fatty acid-producing Yarrowia lipolytica improved the lipopeptide level to around 218 mg/L. The degradation efficiency of oxytetracycline in the four-strain consortium was 100% at 48 h; however, only 56% of the sulfamethoxazole was removed over 96 h. Three five-strain consortia were formed by introducing recombinant manganese peroxidase-producing P. pastoris, recombinant HM618 with high-level amylase, and serine-producing C. glutamicum. In low starch food waste, the highest degradation efficiency of sulfamethoxazole was 71%, while oxytetracycline could be completely removed at 48 h. However, oxytetracycline inhibited starch degradation and lipopeptide production. The high level of starch improved lipopeptide synthesis to 1280 mg/L. The results of this study provide a feasible strategy for the resource utilization of inferior biomass food waste.

Use of reclaimed municipal wastewater in agriculture: Comparison of present practice versus an emerging paradigm of anaerobic membrane bioreactor treatment coupled with hydroponic controlled environment agriculture

Advancements in anaerobic membrane bioreactor (AnMBR) technology have opened up exciting possibilities for sustaining precise water quality control in wastewater treatment and reuse. This approach not only presents an opportunity for energy generation and recovery but also produces an effluent that can serve as a valuable nutrient source for crop cultivation in hydroponic controlled environment agriculture (CEA). In this perspective article, we undertake a comparative analysis of two approaches to municipal wastewater utilization in agriculture. The conventional method, rooted in established practices of conventional activated sludge (CAS) wastewater treatment for soil/land-based agriculture, is contrasted with a new paradigm that integrates AnMBR technology with hydroponic (soilless) CEA. This work encompasses various facets, including wastewater treatment efficiency, effluent quality, resource recovery, and sustainability metrics. By juxtaposing the established methodologies with this emerging synergistic model, this work aims to shed light on the transformative potential of the integration of AnMBR and hydroponic-CEA for enhanced agricultural sustainability and resource utilization.

Biodegradation of bisphenol-A in water using a novel strain of Xenophilus sp. embedded onto biochar: Elucidating the influencing factors and degradation pathway

Bisphenol-A (BPA) is an emerging hazardous contaminant, which is ubiquitous in the environment and can cause endocrine disruptor and cancer risks. Therefore, biodegradation of BPA is an essential issue to mitigate the associated human health. In this work, a bacterial strain enables of degrading BPA, named BPA-LRH8 (identified as Xenophilus sp.), was newly isolated from activated sludge and embedded onto walnut shell biochar (WSBC) to form a bio-composite (BCM) for biodegradation of BPA in water. The Langmuir maximum adsorption capacity of BPA by WSBC was 21.7 mg g-1. The free bacteria of BPA-LRH8 showed high BPA degradation rate (∼100 %) at pH 5-11, while it was lower (＜20 %) at pH 3. The BCM eliminated all BPA (∼100 %) at pH 3-11 and 25-45 °C when the BPA level was ≤ 25 mg L-1. The spectrometry investigations suggested two possible degradation routes of BPA by Xenophilus sp. In one route, BPA (C15H16O3) was oxidized to C15H16O3, and then broken into C9H12O3 through chain scission. In another route, BPA was likely hydroxylated, oxidized, and cleaved into C9H10O4P4, which was further metabolized into CO2 and H2O in the TCA cycle. This study concluded that the novel isolated bacteria (BPA-LRH8) embedded onto WSBC is a promising and new method for the effective removal of BPA and similar hazardous substances from contaminated water under high concentrations and wide range of pH and temperature.

Origin, types, and contribution of emerging pollutants to environmental degradation and their remediation by physical and chemical techniques

The growing presence of emerging pollutants (EPs) in aquatic environments, as well as their harmful impacts on the biosphere and humans, has become a global concern. Recent developments and advancements in pharmaceuticals, agricultural practices, industrial activities, and human personal care substances have paved the way for drastic changes in EP concentrations and impacts on the ecosystem. As a result, it is critical to mitigate EP's harmful effects before they jeopardize the ecological equilibrium of the overall ecosystem and the sustainable existence of life on Earth. This review comprehensively documented the types, origins, and remediation strategies of EPs, and underscored the significance of this study in the current context. We briefly stated the major classification of EPs based on their organic and inorganic nature. Furthermore, this review systematically evaluates the occurrence of EPs due to the fast-changing ecological scenarios and their impact on human health. Recent studies have critically discussed the emerging physical and chemical processes for EP removal, highlighting the limitations of conventional remediation technologies. We reviewed and presented the challenges associated with EP remediation and degradation using several methods, including physical and chemical methods, with the application of recent technologies. The EP types and various methods discussed in this review help the researchers understand the nature of present-day EPs and utilize an efficient method of choice for EP removal and management in the future for sustainable life and development activities on the planet.

Multidimensional occurrence and diet risk of emerging contaminants in freshwater with urban agglomerations

Freshwater systems near highly urbanized areas are extremely susceptible to emerging contaminants (ECs), yet their stereoscopic persistence in aquatic ecosystems and related risks remain largely unknown. Herein, we characterized the multi-mediums distribution of 63 ECs in Baiyangdian Lake, the biggest urban lake in the North of China. We identified variations in the seasonal patterns of aquatic EC levels, which decreased in water and increased in sediment from wet to dry seasons. Surprisingly, higher concentrations and a greater variety of ECs were detected in reeds than in aquatic animals, indicating that plants may contribute to the transferring of ECs. Source analysis indicated that human activity considerably affected the distribution and risk of ECs. The dietary risk of ECs is most pronounced among children following the intake of aquatic products, especially with a relatively higher risk associated with fish consumption. Besides, a comprehensive scoring ranking method was proposed, and 9 ECs, including BPS and macrolide antibiotics, are identified as prioritized control pollutants. These findings highlight the risks associated with aquatic ECs and can facilitate the development of effective management strategies.

Adsorption characteristics and mechanisms of bisphenol A on novel nitrogen-modified biochar derived from waste masks and biomass

Resource utilization of waste masks has become an urgent scientific issue. In this work, with sustainably, waste masks and biomass were co-pyrolysis with oxygen limitation to prepare mask-based biochar (MB). Then, urea was introduced to prepare novel nitrogen modified mask-based biochar (NMB) via a one-step hydrothermal synthesis method. The adsorption characteristics of NMB on the emerging environmental pollutant, bisphenol A (BPA), were evaluated via batch adsorption tests. Moreover, the physicochemical properties of the materials were characterized with various advanced techniques. Also, the roles of waste masks and nitrogen modification were explored. The adsorption mechanisms of NMB on BPA were revealed as well as the performance differences between different adsorbents. The results showed that waste masks participated in thermochemical reactions, shaped the microsphere structure of biochar, and increased the types of surface functional groups. The nitrogen modification enriched the surface elemental composition and activated the specific surface area via the mesopore. These would enhance the adsorption performance. The maximum adsorption of BPA by NMB was 62.63 mg·g-1, which was approximately 2.35-5.58 times higher than that of the control materials. Temkin model and pseudo-second-order model optimally simulate the isothermal and kinetic adsorption, respectively. The adsorption mechanisms are jointly by physical and chemical adsorption, which mainly includes π-π interaction, hydrogen bonding, intraparticle diffusion, surface adsorption, and ion exchange. After discussion and evaluation, NMB has lower preparation process cost (7.21 USD·kg-1) and safety, with potential for environmental applications. This study aims to expand new ideas for the comprehensive utilization of waste masks and the preparation of eco-friendly materials. Moreover, it provides a theoretical basis for the removal of BPA.

Food wastewater treatment using a hybrid biofilm reactor: nutrient removal performance and functional microorganisms on filler biofilm and suspended sludge

In this study, a laboratory-scale hybrid biofilm reactor (HBR) was constructed to treat food wastewater (FWW) before it is discharged into the sewer. The chemical oxygen demand (COD) of 29 860 mg L-1 in FWW was degraded to 200-350 mg L-1 using the HBR under the operating parameters of COD load 1.68 kg m-3 d-1, hydraulic retention time (HRT) of 426.63 h, dissolved oxygen (DO) of 8-9 mg L-1, and temperature of 22-23 °C. The biomass of biofilm on the surface of filler was 2.64 g L-1 for column A and 0.91 g L-1 for column O. Microbial analysis revealed richer and more diverse microorganisms in filler biofilms compared to those in suspended sludge. The hybrid filler was conducive to the development of functional microbial species, including phyla Firmicutes, Actinobacteriota, and Chloroflexi, and genus level norank_f_JG30-KF-CM45, which will improve FWW treatment efficiency. Moreover, the microorganisms on the filler biofilm had more connections and relationships than those in the suspended sludge. The combination of an up-flow anaerobic sludge bed (UASB) and HBR was demonstrated to be an economical strategy for practical applications as a shorter HRT of 118.34 h could be obtained. Overall, this study provides reliable data and a theoretical basis for the application of HBR and FWW treatments.

Facile fabrication of chitosan/bone/bamboo biochar beads for simultaneous removal of co-existing Cr(VI) and bisphenol a from water

Heavy metal Cr(VI) and organic BPA have posed harmful risks to human health, aquatic organisms and the ecosystem. In this work, Chitosan/bone/bamboo biochar beads (CS-AMCM) were synthesized by co-pyrolysis and in situ precipitation method. These microbeads featured a particle size of approximately 1 ± 0.2 mm and were rich in oxygen/nitrogen functional groups. CS-AMCM was characterized using XRD, Zeta potential, FTIR, etc. Experiments showed that adsorption processes of CS-AMCM on Cr(VI) and BPA fitted well to Langmuir model, with theoretical maximum capacities of 343.61 mg/g and 140.30 mg/g, respectively. Pore filling, electrostatic attraction, redox, complexation and ion exchange were the main mechanisms for Cr(VI), whereas for BPA, the intermolecular force (hydrogen bond) and pore filling were involved. CS-AMCM with adsorbed Cr(VI) demonstrated effective activation in producing ·OH and ·O2 from H2O2, which degraded BPA and Cr(VI) with the removal rates of 99.2% and 98.2%, respectively. CS-AMCM offers the advantages of low-cost, large adsorption capacity, high catalytic degradation efficiency, and favorable recycling in treating Cr(VI) and BPA mixed wastewater, which shows great potential in treating heavy metal and organic matter mixed pollution wastewater.

Biochar-based functional materials for the abatement of emerging pollutants from aquatic matrices

Biochar has emerged as a versatile and efficient multi-functional material, serving as both an adsorbent and catalyst in removing emerging pollutants (EPs) from aquatic matrices. However, pristine biochar's catalytic and adsorption capabilities are hindered by its poor surface functionality and small pore size. Addressing these limitations involves the development of functionalized biochar, a strategic approach aimed at enhancing its physicochemical properties and improving adsorption and catalytic efficiencies. Despite a growing interest in this field, there is a notable gap in existing literature, with no review explicitly concentrating on the efficacy of biochar-based functional materials (BCFMs) for removing EPs in aquatic environments. This comprehensive review aims to fill this void by delving into the engineering considerations essential for designing BCFMs with enhanced physiochemical properties. The focus extends to understanding the treatment efficiency of EPs through mechanisms such as adsorption or catalytic degradation. The review systematically outlines the underlying mechanisms involved in the adsorption and catalytic degradation of EPs by BCFMs. By shedding light on the prospects of BCFMs as a promising multi-functional material, the review underscores the imperative for sustained research efforts. It emphasizes the need for continued exploration into the practical implications of BCFMs, especially under environmentally relevant pollutant concentrations. This holistic approach seeks to contribute to advancing knowledge and applying biochar-based solutions in addressing the challenges posed by emerging pollutants in aquatic ecosystems.

From wastewater to clean water: Recent advances on the removal of metronidazole, ciprofloxacin, and sulfamethoxazole antibiotics from water through adsorption and advanced oxidation processes (AOPs)

Antibiotics released into water sources pose significant risks to both human health and the environment. This comprehensive review meticulously examines the ecotoxicological impacts of three prevalent antibiotics-ciprofloxacin, metronidazole, and sulfamethoxazole-on the ecosystems. Within this framework, our primary focus revolves around the key remediation technologies: adsorption and advanced oxidation processes (AOPs). In this context, an array of adsorbents is explored, spanning diverse classes such as biomass-derived biosorbents, graphene-based adsorbents, MXene-based adsorbents, silica gels, carbon nanotubes, carbon-based adsorbents, metal-organic frameworks (MOFs), carbon nanofibers, biochar, metal oxides, and nanocomposites. On the flip side, the review meticulously examines the main AOPs widely employed in water treatment. This includes a thorough analysis of ozonation (O3), the photo-Fenton process, UV/hydrogen peroxide (UV/H2O2), TiO2 photocatalysis, ozone/UV (O3/UV), radiation-induced AOPs, and sonolysis. Furthermore, the review provides in-depth insights into equilibrium isotherm and kinetic models as well as prospects and challenges inherent in these cutting-edge processes. By doing so, this review aims to empower readers with a profound understanding, enabling them to determine research gaps and pioneer innovative treatment methodologies for water contaminated with antibiotics.

A critical review on biochar for the removal of toxic pollutants from water environment

As an effort to tackle some of the most pressing ecological issues we are currently experiencing, there has been an increasing interest in employing biomass-derived char products in various disciplines. Thermal combustion of biomass results in biochar production, which is a remarkably rich source of carbon. Not only does the biochar obtained by the thermochemical breakdown of biomass lower the quantity of carbon released into the environment, but it also serves as an eco-friendly substitute for activated carbon (AC) and further carbon-containing products. An overview of using biochar to remove toxic pollutants is the main subject of this article. Several techniques for producing biochar have been explored. The most popular processes for producing biochar are hydrothermal carbonization, gasification and pyrolysis. Carbonaceous materials, alkali, acid and steam are all capable of altering biochar. Depending on the environmental domains of applications, several modification techniques are chosen. The current findings on characterization and potential applications of biochar are compiled in this survey. Comprehensive discussion is given on the fundamentals regarding the formation of biochar. Process variables influencing the yield of biochar have been summarized. Several biochars' adsorption capabilities for expulsion pollutants under various operating circumstances are compiled. In the domain of developing biochar, a few suggestions for future study have been given.

The boom era of emerging contaminants: A review of remediating agricultural soils by biochar

Emerging contaminants (ECs) are widely sourced persistent pollutants that pose a significant threat to the environment and human health. Their footprint spans global ecosystems, making their remediation highly challenging. In recent years, a significant amount of literature has focused on the use of biochar for remediation of heavy metals and organic pollutants in soil and water environments. However, the use of biochar for the remediation of ECs in agricultural soils has not received as much attention, and as a result, there are limited reviews available on this topic. Thus, this review aims to provide an overview of the primary types, sources, and hazards of ECs in farmland, as well as the structure, functions, and preparation types of biochar. Furthermore, this paper emphasizes the importance and prospects of three remediation strategies for ECs in cropland: (i) employing activated, modified, and composite biochar for remediation, which exhibit superior pollutant removal compared to pure biochar; (ii) exploring the potential synergistic efficiency between biochar and compost, enhancing their effectiveness in soil improvement and pollution remediation; (iii) utilizing biochar as a shelter and nutrient source for microorganisms in biochar-mediated microbial remediation, positively impacting soil properties and microbial community structure. Given the increasing global prevalence of ECs, the remediation strategies provided in this paper aim to serve as a valuable reference for future remediation of ECs-contaminated agricultural lands.

Porous activated carbons derived from waste Moroccan pine cones for high-performance adsorption of bisphenol A from water

Porous-activated carbons (ACs) derived from Moroccan pine cones (PC) were synthesised by a two step-chemical activation/carbonisation method using phosphoric acid (PC-H) and zinc chloride (PC-Z) as activating agents and used for the adsorption of bisphenol A (BPA) from water. Several techniques (TGA/DTA, FT-IR, XRD, SEM and BET) were used to determine the surface area and pore characterisation and variations during the preparation of the adsorbents. The modification significantly increased the surface area of both ACs, resulting in values of 1369.03 m2 g-1 and 1018.86 m2 g-1 for PC-H and PC-Z, respectively. Subsequent adsorption tests were carried out, varying parameters including adsorbent dosage, pH, initial BPA concentration, and contact time. Therefore, the highest adsorption capacity was observed when the BPA molecules were in their neutral form. High pH values were found to be unfavourable for the removal of bisphenol A from water. The results showed that BPA adsorption kinetics and isotherms followed pseudo-second-order and Langmuir models. Thermodynamic studies indicated that the adsorption was spontaneous and endothermic. Besides, the regeneration of spent adsorbents demonstrated their reusability. The adsorption mechanisms can be attributed to physical adsorption, hydrogen bonds, electrostatic forces, hydrophobic interactions, and π-π intermolecular forces.

Ammonia hydroxide and citric acid modified wheat straw-biochars: Preparation, characterization, and environmental applications

This study presents an assessment of inorganic and organic modification of biochar on physicochemical properties, dissolved organic carbon (DOC) release, sorption efficiency towards enrofloxacin (E) and silver nanoparticles (Ag-NPs), as well as an evaluation of addition of prepared materials on hydro-physical properties and adsorption capacity of montmorillonite (M). The biochar was derived from wheat straw at 650 °C. An inorganic modification was performed using ammonia hydroxide, whereas an organic modification, using citric acid. The ammonia hydroxide and citric acid changed the biochar nature and surface chemistry by introducing amino and ester groups. The lowest DOC release was from ammonia-biochar (BCN) and the highest, from citric acid-biochar (BCC). The adsorption data were better described by pseudo-II order equation and Marczewski-Jaroniec isotherm. Results showed that BCN exhibited the highest efficiency in adsorption of E and Ag-NPs. It also improved the adsorptive abilities and saturated hydraulic conductivity of M. This provides the chemically modified biochars have an excellent potential to improve pollution removal from aqueous media and hydro-physical/sorption properties of soil sorption complex. They can be used with advantageous in environmental applications.

Novel manganese and nitrogen co-doped biochar based on sodium bicarbonate activation for efficient removal of bisphenol A: Mechanism insight and role analysis of manganese and nitrogen by combination of characterizations, experiments and density functional theory calculations

A novel porous manganese and nitrogen co-doped biochar (Mn-N@SBC) was synthesized via one-step pyrolysis, utilizing loofah agricultural waste as the precursor and NaHCO3 as the activator. The behavior of bisphenol A adsorbed on Mn-N@SBC was evaluated using static batch adsorption experiments. Compared to direct manganese-nitrogen co-doping, co-doping based on NaHCO3 activation significantly increased the specific surface area (231 to 1027 m2·g-1) and adsorption capacity (15 to 351 mg·g-1). Wide pH (2-10) and good resistance to cation/anion, humic acid and actual water demonstrated the robust adaptability of Mn-N@SBC to environmental factors. The significantly reduced specific surface area after adsorption, adverse effects of ethanol and phenanthrene on the removal of bisphenol A, and theoretically predicted interaction sites indicated the primary adsorption mechanisms involved pore filling, hydrophobicity, and π-π-electron-donor-acceptor interaction. This work presented an approach to create high-efficiency adsorbents from agricultural waste, offering theoretical and practical guidance for the removal of pollutants.

Degradation of COD in antibiotic wastewater by a combination process of electrochemistry, hydroxyl-functionalized ball-milled zero-valent iron/Fe3O4 and Oxone

In this study, the significant iron-based material, hydroxyl-functionalized ball-milled zero-valent iron/Fe3O4 (HFB-ZVI/Fe3O4) was employed for the experiments. The performance of the Electro + HFB-ZVI/Fe3O4 + Oxone system for the degradation of chemical oxygen demand (COD) in antibiotic wastewater was investigated. A direct current was applied between a graphite plate anode and two iron plate cathodes, and a series of operational parameters, such as applied electric current, the dosage of HFB-ZVI/Fe3O4 composite, the dosage of Oxone, and initial solution pH, were explored to evaluate the oxidation process. The application of electric current enhanced the gradual degradation of COD and the increase of current intensity accelerated COD degradation. The neutral condition was favourable for the rapid degradation of COD in a short reaction time by the Electro + HFB-ZVI/Fe3O4 + Oxone process and promoted the degradation efficiency of COD. An increase of electric current gradually decreased the reaction solution pH, the larger the electric current applied in the reaction process, the lower the final pH of the reaction solution. Under the optimal experimental conditions (1 g/L HFB-ZVI/Fe3O4 composite, 0.3 g/L Oxone, current intensity = 500 mA, initial solution pH = 7.85), Electro + HFB-ZVI/Fe3O4 + Oxone achieved 99% COD degradation in antibiotic wastewater. Radicals quenching experiments indicated the contribution to COD degradation by hydroxyl radicals (HO•), sulphate radicals (SO4•-) and other oxidants were 66.03%, 24.014% and 9.756%, respectively. The possible mechanism of COD degradation in the Electro + HFB-ZVI/Fe3O4 + Oxone system was also discussed in this study. The findings in this work provided useful information for the treatment of wastewater.

Highly efficient adsorption of ciprofloxacin from aqueous solutions by waste cation exchange resin-based activated carbons: Performance, mechanism, and theoretical calculation

This study focused on the preparation of a highly efficient activated carbon adsorbent from waste cation exchange resins through one-step carbonization to remove ciprofloxacin (CIP) from aqueous solutions. Scanning electron microscopy, X-ray diffraction, Fourier-transform infrared spectrometry, and X-ray photoelectron spectroscopy were used to characterize the physicochemical properties of the carbonized materials. The CIP removal efficiency, influencing factors, and adsorption mechanisms of CIP on the carbonized resins were investigated. Density functional theory (DFT) computations were performed to elucidate the adsorption mechanisms. The CIP removal reached 93 % when the adsorbent dosage was 300 mg/L at 25 °C. The adsorption capacity of the carbonized resins to CIP gradually decreased with an increasing pH from 3.0 to 7.0 and sharply declined with a pH from 7.0 to 11.0. The adsorption process better fitted by the pseudo second-order kinetic and Langmuir models, indicating that the interaction between CIP and the carbonized resins was monolayer adsorption. The maximum adsorption capacity fitted by the Langmuir model was 384.4 mg/g at 25 °C. Microstructural analysis showed that the adsorption of CIP on the carbonized resins was a joint effect of H-bonding, ion exchange, and graphite-N adsorption. Computational results signified the strong H-bonding and ion exchange interactions existed between CIP and carbonized resins. The high adsorption and reusability suggest that waste cation exchange resin-based activated carbons can be used as an effective and reusable adsorbent for removing CIP from aqueous solutions.

Fixed-bed adsorption studies of endocrine-disrupting compounds from water by using novel calcium-based metal-organic frameworks

The presence of emerging water pollutants such as endocrine-disrupting compounds (EDCs), including 17-ethynylestradiol (EE2), bisphenol A (BPA), and perfluorooctanoic acid (PFOA), in contaminated water sources poses significant environmental and health challenges. This study aims to address this issue by investigating the efficiency of novel calcium-based metal-organic frameworks, known as mixed-linker calcium-based metal-organic frameworks (Ca-MIX), in adsorbing these endocrine-disrupting compounds. This study analyzed the influence of influent concentration, bed height, and flow rate on pollutant removal, with bed height emerging as a crucial factor. From the breakthrough curves, it was determined that the column maximum adsorption capacities followed the order of 17-ethynylestradiol (101.52 μg/g; 40%) > bisphenol A (99.07 μg/g; 39%) > perfluorooctanoic acid (81.28 μg/g; 32%). Three models were used to predict the adsorption process, with the Yan model outperforming the other models. This suggests the potential of mixed-linker calcium-based metal-organic frameworks for removing endocrine-disrupting compounds from water, using the Yan model as an effective predictor. Overall, this study provides valuable insights for the development of effective water treatment methods using mixed-linker calcium-based metal-organic frameworks to remove endocrine-disrupting compounds from contaminated water sources.

Recent trends and economic significance of modified/functionalized biochars for remediation of environmental pollutants

The pollution of soil and aquatic systems by inorganic and organic chemicals has become a global concern. Economical, eco-friendly, and sustainable solutions are direly required to alleviate the deleterious effects of these chemicals to ensure human well-being and environmental sustainability. In recent decades, biochar has emerged as an efficient material encompassing huge potential to decontaminate a wide range of pollutants from soil and aquatic systems. However, the application of raw biochars for pollutant remediation is confronting a major challenge of not getting the desired decontamination results due to its specific properties. Thus, multiple functionalizing/modification techniques have been introduced to alter the physicochemical and molecular attributes of biochars to increase their efficacy in environmental remediation. This review provides a comprehensive overview of the latest advancements in developing multiple functionalized/modified biochars via biological and other physiochemical techniques. Related mechanisms and further applications of multiple modified biochar in soil and water systems remediation have been discussed and summarized. Furthermore, existing research gaps and challenges are discussed, as well as further study needs are suggested. This work epitomizes the scientific prospects for a complete understanding of employing modified biochar as an efficient candidate for the decontamination of polluted soil and water systems for regenerative development.

Application of biochar in microbial fuel cells: Characteristic performances, electron-transfer mechanism, and environmental and economic assessments

Biochar is a by-product of thermochemical conversion of biomass or other carbonaceous materials. Recently, it has garnered extensive attention for its high application potential in microbial fuel cell (MFC) systems owing to its high conductivity and low cost. However, the effects of biochar on MFC system performance have not been comprehensively reviewed, thereby necessitating the evaluation of the efficacy of biochar application in MFCs. In this review, biochar characteristics were outlined based on recent publications. Subsequently, various applications of biochar in the MFC systems and their probable processes were summarized. Finally, proposals for future applications of biochar in MFCs were explored along with its perspectives and an environmental evaluation in the context of a circular economy. The purpose of this review is to gain comprehensive insights into the application of biochar in the MFC systems, offering important viewpoints on the effective and steady utilization of biochar in MFCs for practical application.

Strategic use of crop residue biochars for removal of hazardous compounds in wastewater

Crop residues are affordable lignocellulosic waste in the world, and a large portion of the waste has been burned, releasing toxic pollutants into the environment. Since the crop residue is a carbon and ingredient rich material, it can be strategically used as a sorptive material for (in)organic pollutants in the wastewater after thermo-chemical valorization (i.e., biochar production). In this review, applications of crop residue biochars to adsorption of non-degradable synthetic dyes, antibiotics, herbicides, and inorganic heavy metals in wastewater were discussed. Properties (porosity, functional groups, heteroatom, and metal(oxide)s, etc.) and adsorption capacity relationships were comprehensively reviewed. The current challenges of crop residue biochars and guidelines for development of efficient adsorbents were also provided. In the last part, the future research directions for practical applications of the crop residue biochars in wastewater treatment plants have been suggested.

Effective immobilization of bisphenol A utilizing activated biochar incorporated into soil: combined with batch adsorption and fixed-bed column studies

This study presented the mixture of biochar and soil for removal of bisphenol A (BPA) to assess environmental remediation ability. Using phoenix tree leaves as biomass and phosphoric acid as activator, after one-step hydrothermal and short-term activation, the eventual solid product was phosphoric acid hydrothermal activated carbon (HPC). The characterizations showed that HPC had the high specific surface (994.21 m2·g-1), and large unsaturated esters and hydroxyl groups. The saturated adsorption capacities of batch and column adsorption for the addition of 0.5% HPC to soil were 0.790 mg·g-1 and 67.23 mg·kg-1, while to the natural soil were 0.236 mg·g-1 and 8.75 mg·kg-1, respectively. The adsorption kinetics and thermodynamic analysis indicated that the adsorption process utilizing HPC incorporated into soil was a chemical reaction rate-controlled, physical-dominated multilayer adsorption, and spontaneous endothermic. Also, batch adsorption experiments and analysis were performed under different pH levels, HPC contents, organic acid concentrations, and cationic strengths. Successively, fixed-bed column experiments were carried out with and without the HPC; the results showed that the wide mass transfer zone led to the effective fixation of BPA, and the organic acid had no obvious effect on the fixation of BPA when the 1.0% HPC mixed with soil. Finally, through characterizations and data analysis, the enhanced adsorption of BPA by HPC mixed with soil mainly relied on π-π interaction, hydrogen bonding, followed by electrostatic attraction and pore filling.

The efficient removal of ibuprofen, caffeine, and bisphenol A using engineered egusi seed shells biochar: adsorption kinetics, equilibrium, thermodynamics, and mechanism

Contaminants of emerging concern (CECs), also known as micropollutants, have been recognized in recent years as substantial water pollutants because of the potential threats they pose to the environment and human health. This study was aimed at preparing biochar (BC) based on egusi seed shells (ESS) with well-developed porosity and excellent adsorption capacity towards CECs including ibuprofen (IBP), caffeine (CAF), and bisphenol A (BPA). BC samples were prepared by pyrolysis at different temperatures (400 to 800 °C) and were characterized using nitrogen sorption, FTIR, powder X-ray diffraction (PXRD), SEM/EDS, elemental analysis, and thermal analysis. The nitrogen sorption and SEM results showed that the textural properties were more prominent as the pyrolysis temperature increased. The BC sample obtained at 800 °C which exhibited the largest specific surface area (688 m2/g) and the highest pore volume (0.320 cm3/g) was selected for the adsorption study of CECs. The kinetic study shows that the adsorption equilibrium of CAF and BPA was faster than that of IBP. The pseudo-first- and pseudo-second-order kinetic models best fitted the adsorption data. The Langmuir maximum monolayer adsorption capacities of biochar were found to be ~ 180, 121, and 73 mg/g respectively for IBP, CAF, and BPA. The thermodynamic study shows that the adsorption process was spontaneous and endothermic for the three CECs. The results of the adsorption and the analysis of BC after adsorption showed that hydrogen bonding, van der Waals, π-π, n-π interactions, and pore filling were involved in the adsorption mechanism. The prepared biochar BC from ESS displayed a large surface area and good morphology and significantly promotes adsorption of CECs and good efficiency on synthetic effluent. Finally, it offers a low-cost and cleaner production method.

Porous biochar derived from walnut shell as an efficient adsorbent for tetracycline removal

In this study, a high-performance porous adsorbent was prepared from biochar through a simple one-step alkali-activated pyrolysis treatment of walnut shells, and it was effective in removing tetracycline (TC). The specific surface area (SSA) of potassium hydroxide-pretreated walnut shell-derived biochar pyrolyzed at 900°C (KWS900) increased remarkably compared to that of the pristine walnut shell and reached 1713.87±37.05 m²·g^-1. The maximum adsorption capacity of KWS900 toward TC was 607.00±31.87 mg·g^-1. The pseudo-second-order kinetic and Langmuir isotherm models were well suited to describe the TC adsorption process onto KWS900. The KWS900 exhibited high stability and reusability for TC adsorption in the presence of co-existing anions or cations over a wide pH range of 1.0-11.0. Further investigations demonstrated that the proposed adsorption mechanism involved pore filling, hydrogen bonding, π-π stacking, and electrostatic interaction. These findings provide a valuable reference for developing biochar-based adsorbents for pollutant removal.

Preparation of carbon self-doped g-C3N4 for efficient degradation of bisphenol A under visible light irradiation

In this study, visible-light-driven carbon self-doped graphitic carbon nitride photocatalyst was fabricated by a facile method with urea and ammonium citrate, and used for photodegradation of bisphenol A (BPA) in the aqueous environment. The experiments indicated that the prepared photocatalyst (C_0.02CN) showed high catalytic activity, and 96.0%, 93.2%, and 95.5% BPA could be photodegraded in 150 min under pH 3, 6, and 11, respectively. The photocatalytic degradation rate (0.018 min^-1) and mineralization (27.6%) of C_0.02CN for BPA were about 6.7 and 3.5 times higher than those of the g-C₃N₄ (0.0027 min^-1, 7.87%), respectively. C_0.02CN had high reusability with a photodegradation efficiency of 84.5% for BPA after 3 cycles. Moreover, C_0.02CN introduced additional carbon atoms, which generated C-O-C bonds in the g-C₃N₄ lattice. In contrast to g-C₃N₄, carbon doping enhanced the visible light absorption range of C_0.02CN, reduced its band gap, and improved the separation efficiency of photogenerated electron-hole pairs. Radical quenching experiment and ESR results revealed that superoxide radicals (•O₂^-) and photogenerated holes (h⁺) acted as important parts in the high photodegradation activity under visible light irradiation. This work puts forward a one-pot strategy for the preparation of carbon self-doped g-C₃N₄, displacing the high-energy consuming and complicated preparation technology with promising industrial applications.

Pyrolysis temperature affects the physiochemical characteristics of lanthanum-modified biochar derived from orange peels: Insights into the mechanisms of tetracycline adsorption by spectroscopic analysis and theoretical calculations

Biochar (BC) derived from orange peels was modified using LaCl₃ to enhance its tetracycline (TC) adsorption capacity. SEM-EDS, FT-IR, XRD, and BET were used to characterize the physiochemical characteristics of La-modified biochar (La-BC). Batch experiments were conducted to investigate the effects of several variables like pyrolysis temperature, adsorbent dosage, initial pH, and coexisting ions on the adsorption of TC by La-BC. XPS and density functional theory (DFT) were used to elucidate the TC adsorption mechanism of La-BC. The results demonstrated that La was uniformly coated on the surface of the La-BC. The physiochemical characteristics of La-BC highly depended on pyrolysis temperature. Higher temperature increased the specific surface area and functional groups of La-BC, thus enhancing its TC adsorption capacity. La-BC prepared at 700 °C (BC@La-700) achieved the maximum adsorption capacity of 143.20 mg/g, which was 6.8 and 4.6 times higher than that of BC@La-500 and BC@La-600, respectively. The mechanisms of TC adsorption by La-BC were most accurately described by the pseudo-second-order kinetic model. Furthermore, the adsorption isotherm of La-BC was consistent with the Freundlich model. BC@La-700 achieved good TC adsorption efficiencies even at a wide pH range (pH 4-10). Humic acid significantly inhibited TC adsorption by La-BC. The presence of coexisting ions (NH₄⁺, Ca²⁺, NO₃^-) did not significantly affect the adsorption capacity of La-BC, particularly BC@La-700. Moreover, BC@La-700 also exhibited the best recycling performance, which achieved relative high adsorption capacity even after 5 cycles. The XPS results showed that π-π bonds, oxygen-containing functional groups, and La played a major role in the adsorption of TC on La-BC. The result of DFT showed that the adsorption energy of La-BC was the greatest than that of other functional groups on biochar. Collectively, our findings provide a theoretical basis for the development of La-BC based materials to remove TC from wastewater.

A review of antibiotics and antibiotic resistance genes (ARGs) adsorption by biochar and modified biochar in water

Antibiotics have been used in massive quantities for human and animal medical treatment, and antibiotic resistance genes (ARGs) are of great concern worldwide. Antibiotics and ARGs are exposed to the natural environment through the discharge of medical wastewater, causing great harm to the environment and human health. Biochar has been widely used as a green and efficient adsorbent to remove pollutants. However, pristine and unmodified biochars are not considered sufficient and efficient to cope with the current serious water pollution. Therefore, researchers have chosen to improve the adsorption capacity of biochar through different modification methods. To have a better understanding of the application of modified biochar, this review summarizes the biochar modification methods and their performance, particularly, molecular imprinting and biochar aging are outlined as new modification methods, influencing factors of biochar and modified biochar in adsorption of antibiotics and ARGs and adsorption mechanisms, wherein adsorption mechanism of ARGs on biochar is found to be different than that of antibiotics. After that, the directions of biochar and modified biochar worthy of research and the issues that need attention are proposed. It can be noted that under the current dual carbon policy, biochar may have wider application prospects in future.

Chemical modification of biochars as a method to improve its surface properties and efficiency in removing xenobiotics from aqueous media

Biochar (BC) is a carbonaceous material produced by pyrolysis of biomass, applied in various areas such as water purification, fuel production, soil amendment, etc. Many types of BC are characterized by insufficient textural parameters or poor surface chemistry, and hence by low adsorption capacity. This makes innovative chemical methods increasing BC ability to remove xenobiotics from aquatic environments highly needed. Many of them have already been described in the literature. This review presents them in detail and evaluates their effectiveness in improving textural parameters, surface chemistry, and adsorption capacity of BC.

Effects of biochar on anaerobic treatment systems: Some perspectives

Many anaerobic activities involve carbon, nitrogen, iron, and sulfur cycles. As a well-developed porous material with abundant functional groups, pyrolytic biochar has been widely researched in efforts to promote microbial activities. However, the lack of consensus on the biochar mechanism has limited its practical application. This review summarizes the effects of different pyrolysis temperatures, particle sizes, and dosages of biochar on microbial activities and community in Fe(III) reduction, anaerobic digestion, nitrogen removal, and sulfate reduction systems. It was found that biochar could promote anaerobic activities by stimulating electron transfer, alleviating toxicity, and providing suitable habitats for microbes. However, it inhibits microbial activities by releasing heavy metal ions or persistent free radicals and adsorbing signaling molecules. Finding a balance between the promotion and inhibition of biochar is therefore essential. This review provides valuable perspectives on how to achieve efficient and stable use of biochar in anaerobic systems.

Modified biochar: synthesis and mechanism for removal of environmental heavy metals

With social progress and industrial development, heavy metal pollution in water and soils environment is becoming more serious. Although biochar is a low-cost and environmentally friendly adsorbent for heavy metal ions, its adsorption and immobilization efficiency still need to be improved. As an upgraded version of biochar, modified biochar has attracted extensive attention in the scientific community. This review summarized the recent research progress on the treatment methods on heavy metal pollutants in water and soils using biochar. The features and advantages of biochar modification techniques such as physical modification, chemical modification, biological modification and other categories of biochar were discussed. The mechanism of removing heavy metals from soil and water by modified biochar was summarized. It was found that biochar had better performance after modification, which provided higher surface areas and more functional groups, and had enough binding sites to combine heavy metal ions. Biochar is a very promising candidate for removing heavy metals in environment. Furthermore, some high valent metal ions could be reduced to low valent metals, such as Cr(VI) reduction to Cr(III), and form precipitates on biochar by in-situ sorption-reduction-precipitation strategy. However, it is still the direction of efforts to develop high-efficiency modified biochar with low-cost, high sorption capacity, high photocatalytic performance, environmentally friendly and no secondary pollution in future.

A scientometric analysis of research trends on emerging contaminants in the field of cancer in 2012-2021

INTRODUCTION

Recently, emerging contaminants have been discovered in the aquatic environment that can cause a range of human diseases, including cancer. In this study, our scientometric analysis provides a comprehensive overview of emerging contaminants and cancer research from 2012 to 2021.

METHODS

The Web of Science Core Collection Database was used to retrieve all related publications. The bibliometix R-package, CiteSpace, and VOSviewer were applied to collect information on annual citations and publications, famous journals and authors, the most productive countries and organizations, popular topics, and keywords.

RESULTS

A total of 2378 publications were retrieved. The publication's output showed a gradual upward trend from 2012 to 2021. The most-cited paper was a review article by Vandenberg et al. that was published in 2012. According to the analysis results, the United States published the most articles. The closest collaboration was between the United States and China. Environmental Research and Science of The Total Environment published the most paper. It was Choi KC who was the most productive and had the highest h-index, g-index, and m-index among the authors. The most frequently used keywords were "exposure," "endocrine-disrupting chemicals," "endocrine disruptors," "cancer," "bisphenol-a," and so on.

DISCUSSION

Emerging contaminants play a significant role in cancer development. However, most studies are conducted in vivo with human cells or animal models, and relatively few are on human models. The scientometric analysis offers researchers a clear picture of the current state of research and hotspots in this field. From our study, researchers may find some hotspots that merit in-depth investigation.

Biochar derived carbonaceous material for various environmental applications: Systematic review

Biochar is the solid material produced from the carbonization of organic feedstock biomass. This material has several unique characteristics such as greater carbon content, good electrical conductivity, high stability and large surface area, which can be applied in several research areas such as generation of power and wastewater treatment. In connection with this, recently, the investigations on biochar significantly focus on the removal of toxic heavy metals since the biochar material is easily available and environmentally friendly. According to an environmental analytical device, biochar-derived carbonaceous material has been additionally applied to the synthesis of an effective, sensitive, and low-cost electrochemical sensor. Biochar with an assessment of electrochemical properties has engaged with different redox reactions in water. In this survey, electrochemical ways of behaving of biochar in light of the electrochemical structures were analytically compiled as well as the impact from biomass sources and manufacturing process including carbonization strategies, pre-treatment/changed techniques. This review emphasizes the various synthesis methods of biochar form organic feedstock, properties and different modulations of biochar for the bioremediation of heavy metals. This review study emphasizes the utilization of biochar as sensing platform and supercapacitor for electrode fabrication in electrochemical biosensor to enhance the remediation of toxic contaminants from water streams and by switching the less ecological traditional materials. Brief information on the techniques employed for packaging biochar as carbon electrode is summarized. Scope in the aspect of environmental concern of biochar, future challenges and prospects are proposed in detail.

A comprehensive review of various approaches for treatment of tertiary wastewater with emerging contaminants: what do we know?

In the last few decades, environmental contaminants (ECs) have been introduced into the environment at an alarming rate. There is a risk to human health and aquatic ecosystems from trace levels of emerging contaminants, including hospital wastewater (HPWW), cosmetics, personal care products, endocrine system disruptors, and their transformation products. Despite the fact that these pollutants have been introduced or detected relatively recently, information about their characteristics, actions, and impacts is limited, as are the technologies to eliminate them efficiently. A wastewater recycling system is capable of providing irrigation water for crops and municipal sewage treatment, so removing ECs before wastewater reuse is essential. Water treatment processes containing advanced ions of biotic origin and ECs of biotic origin are highly recommended for contaminants. This study introduces the fundamentals of the treatment of tertiary wastewater, including membranes, filtration, UV (ultraviolet) irradiation, ozonation, chlorination, advanced oxidation processes, activated carbon (AC), and algae. Next, a detailed description of recent developments and innovations in each component of the emerging contaminant removal process is provided.

Fixed bed column performance of Al-modified biochar for the removal of sulfamethoxazole and sulfapyridine antibiotics from wastewater

In this study, biochar derived from bamboo pretreated with aluminum salt was synthesized for the removal of two sulfonamide antibiotics, sulfamethoxazole (SMX) and sulfapyridine (SPY), from wastewater. Batch sorption experiments showed that Al-modified bamboo biochar (Al-BB-600) removed both sulfonamides effectively with the maximum sorption capacity of 1200-2200 mg/kg. The sorption mechanism was mainly controlled by hydrophobic, π-π, and electrostatic interactions. Fixed bed column experiments with Al-modified biochar packed in different dosages (250, 500 and 1000 mg) and flow rates (1, 2 and 4 mL/min) showed the dosage of 1000 mg and flow rate of 1 mL/min performed the best for the removal of both SMX and SPY from wastewater. Among the breakthrough (BT) models used to evaluate the fixed bed filtration performance of Al-BB-600, the Yan model best described the BT behavior of the two sulfonamides, suggesting that the adsorption process involved multiple rate-liming factors such as mass transfer at the solid surface and diffusion Additionally, the Bed Depth Service Time (BDST) model results indicated that Al-BB-600 can be efficiently used in fixed bed column for the removal of both SMX and SPY in scaled-up continuous wastewater flow operations. Therefore, Al-modified biochar can be considered a reliable sorbent in real-world application for the removal of SMX and SPY from wastewater.

Biochar raw material selection and application in the food chain: A review

As one of the largest carbon emitters, China promises to achieve carbon emissions neutrality by 2060. Various industries are developing businesses to reduce carbon emissions. As an important greenhouse gas emissions scenario, the reduction of carbon emissions in the food chain can be achieved by preparing the wastes into biochar. The food chain, as one of the sources of biochar, consists of production, processing and consumption, in which many wastes can be transferred into biochar. However, few studies use the food chain as the system to sort out the raw materials of biochar. A systematic review of the food chain application in serving as raw materials for biochar is helpful for further application of such technique, providing supportive information for the development of biochar preparation and wastes treating. In addition, there are many pollution sources in the food production process, such as agricultural contaminated soil and wastewater from livestock and aquatic, that can be treated on-site to achieve the goal of treating wastes with wastes within the food chain. This study focuses on waste resource utilization and pollution remediation in the food chain, summarizing the sources of biochar in the food chain and analyzing the feasibility of using waste in food chain to treat contaminated sites in the food chain and discussing the impacts of the greenhouse gas emissions. This review provides a reference for the resource utilization of waste and pollution reduction in the food chain.

Sodium alginate/magnetic hydrogel microspheres from sugarcane bagasse for removal of sulfamethoxazole from sewage water: Batch and column modeling

Magnetic carbon were synthesized from sugarcane bagasse using hydrothermal carbonization followed by thermal activation was converted to solid state as beads (hydrogels SACFe) using sodium alginate and applied as adsorbent in removal sulfamethoxazole in batch and column mode. From adsorption parameter analysis it was confirmed that 0.6 g L^-1 SACFe was effective in removing 50 mg L^-1 of SMX at pH 6.2. Sorption of SMX on SACFe beads followed Elovich kinetics and Freundlich isotherm. It was further confirmed that sorption occurred on heterogeneous surface of SACFe beads with chemisorption as rate limiting step. Maximum adsorption capacity was obtained as 58.439 mg g^-1 pH studies revealed that charged assisted hydrogen bonding, EDA interactions are some of the mechanism that favoured removal of SMX. From column studies it was found that bead height of 2 cm and flow rate of 1.5 mL min^-1 found to be best in removing pollutant. Thomas model fitted better the experimental data stating that improved interaction between adsorbent and adsorbate act as major driving force tool in obtaining maximum sorption capacity. Breakthrough curve was completely affected by varied flow rate and bed height. Column adsorption was effective in reducing COD and BOD levels of sewage which are affected by toxic pollutants and miscellaneous compounds. Feasibility analysis showed that SACFe beads could be employed for real-time applications as it is cost, energy effective and easy recovery.

NaOH-assisted H2O2 post-modification as a novel approach to enhance adsorption capacity of residual coffee waste biochars toward radioactive strontium: Experimental and theoretical studies

In this study, NaOH-assisted H₂O₂ post-modification was proposed as a novel strategy to enhance the adsorption of radioactive strontium (Sr) onto residual coffee waste biochars (RCWBs). To validate its viability, the adsorption capacities and mechanisms of Sr(II) using pristine (RCWB_P), H₂O₂ post-modified (RCWB_HP), and NaOH-assisted H₂O₂ post-modified residual coffee waste biochars (RCWB_NHP) were experimentally and theoretically investigated. The highest adsorption capacity of Sr(II) for RCWB_NHP (10.91 mg/g) compared to RCWB_HP (5.57 mg/g) and RCWB_P (5.07 mg/g) was primarily attributed to higher negative surface zeta potential (RCWB_NHP = -5.66 → -30.97 mV; RCWB_HP = -0.31 → -11.29 mV; RCWB_P = 1.90 → -10.40 mV) and decoration of Na on the surfaces of RCWB_P via NaOH-assisted H₂O₂ post-modification. These findings agree entirely with the theoretical observations that the adsorption of Sr(II) onto RCWB_P and RCWB_HP was controlled by electrostatic interactions involving carbonyls whereas enriched carboxylic acids and decorated Na on the surfaces of RCWB_NHP through the replacement of Mg and K by NaOH-assisted H₂O₂ modification stimulated electrostatic interactions and cation exchanges governing the adsorption of Sr(II). Hence, NaOH-assisted H₂O₂ post-modification seemed to be practically applicable for improving the adsorption capacity of Sr(II) using RCWB-based carbonaceous adsorbents in real water matrices.

Enhanced adsorption performance of sulfamethoxazole and tetracycline in aqueous solutions by MgFe2O4-magnetic biochar

Biochar has been reported as an excellent adsorbent for antibiotics, but the application faces the challenges of complicated separation. Here, MgFe₂O₄-magnetic biochars (MBCs) derived from corncob were synthesized at 300 °C to remove sulfamethoxazole (SMX) and tetracycline (TC) simultaneously. The characteristics of MBC300 had a high magnetic intensity. MBC300 had the maximum adsorption capacity of SMX with 50.75 mg/g and the high adsorption amount of TC with 120.36 mg/g respectively, which were 4.49 and 6.48 times those of BC300. MBC300 had the advantage of energy conservation compared with MBC450 and MBC600. The better fitting kinetics and isotherms indicated that the SMX and TC sorption onto MBC300 were governed by chemisorption. FTIR and XPS analyses confirmed that the SMX sorption onto MBC300 was dominated by polar interactions and π-π electron donor-acceptor interactions (π-π EDA). Furthermore, the TC sorption was involved in pore filling, π-π EDA, H-bonds, and surface complexation. MBC300 presented effective adsorption of SMX and TC over a wide range of pH. The competition between antibiotics and coexisting pollutants of dissolved organic matter (DOM), Ca²⁺, CO₃^2-, and PO₄^3- significantly inhibited the sorption. The results indicate that MBC300 is an effective and promising adsorbent to treat SMX and TC simultaneously.

Highly Effective Removal of Ofloxacin from Water with Copper-Doped ZIF-8

Residual antibiotics in wastewater have gained widespread attention because of their toxicity to humans and the environment. In this work, Cu-doped ZIF-8s (Cu-ZIF-8s) were successfully synthesized by the impregnation of Cu²⁺ in ZIF-8 and applied in the removal of ofloxacin (OFX) from water. Remarkably, excellent adsorption performance was obtained in Cu-ZIF-8s, especially for Cu-ZIF-8-1, in which the adsorption capacity (599.96 mg·g⁻¹) was 4.2 times higher than that of ZIF-8 and superior to various adsorbents reported previously. The adsorption kinetics and adsorption isotherm follow the pseudo-second-order model and the Langmuir model, respectively. Furthermore, the removal efficiencies of OFX in Cu-ZIF-8-1 reached over 90% at low concentrations. It was revealed that electrostatic interaction and complexation play important roles in the adsorption process. In addition, the material can be regenerated by simple methods. Therefore, the obtained Cu-doped MOFs may have a promising application in the treatment of antibiotic-containing wastewater.

Concurrent elimination and stepwise recovery of Pb(II) and bisphenol A from water using β-cyclodextrin modified magnetic cellulose: adsorption performance and mechanism investigation

Coexistence of heavy metals and endocrine disrupting compounds in polluted water with competitive adsorption behavior necessitates design of tailored adsorbents. In this work, β-cyclodextrin modified magnetic rice husk-derived cellulose (β-CD@MRHC) which can provide independent functional sites for effectively binding the above two types of contaminants was synthesized and used for Pb(II) and BPA elimination in both unit and multivariate systems. Characterizations results confirmed successful β-CD grafting and Fe₃O₄ loading, and the β-CD@MRHC had excellent magnetic property for its effectively recovery from water, which was not affected by the adsorption of pollutants. The β-CD@MRHC possessed superior adsorption performance with maximal Pb(II)/BPA uptake of 266.2 or 412.8 mg/g, severally, and the adsorption equilibrium was fleetly reached in 30 and 7.5 min. Moreover, the β-CD@MRHC could accomplish synergetic Pb(II) and BPA elimination through averting their competitive behaviors owing to diverse capture mechanisms for Pb(II) (ion exchange, complexation and electrostatic attraction) and BPA (hydrogen bonding and host-guest inclusion). Furthermore, after three cycles of step-wise desorption, the binding of Pb(II) as well as BPA byβ-CD@MRHC dropped slightly in dualistic condition. In summary, β-CD@MRHC was a promising tailored adsorbent to practical application for simultaneously removing heavy metals and organic matters from wastewater with high-performance magnetic recovery.