Synthesis of silver phosphate/sillenite bismuth ferrite/graphene oxide nanocomposite and its enhanced visible light photocatalytic mechanism

Highly Efficient Activation of Peroxymonosulphate by Co and Cu Co-Doped Sawdust Biochar for Ultra-Fast Removal of Bisphenol A

The rapid, efficient, and thorough degradation of Bisphenol A (BPA) is challenging. In this study, we prepared an effective peroxymonosulphate (PMS) activation catalyst derived from sawdust containing calcium carbonate. The Co and Cu co-doped sawdust biochar (CoO/CuO@CBC) catalyst could activate PMS quickly, and the degradation rate of BPA reached 99.3% in 5 min, while the rate constant was approximately 30 times higher than in the CBC/PMS and CoCuOx/PMS systems. Moreover, the interaction between CoO, CuO, and CBC endows the CoO/CuO@CBC catalyst with excellent catalytic performance under different conditions, such as initial pH, temperature, water matrix, inorganic anions, and humic acid, which maintained fast PMS activation via the cyclic transformation of Cu and Co for BPA degradation. The results demonstrated that both the radical (•O2- and •SO4-) and non-radical (1O2) pathways participate in the degradation of BPA in the CoO/CuO@CBC/PMS system. The efficient and stable degradation over a wide range of pH, temperature, and aqueous matrices indicates the potential application of the CoO/CuO@CBC catalyst.

Bi2Fe4O9/rGO nanocomposite with visible light photocatalytic performance for tetracycline degradation

Bismuth-iron semiconductor materials have been widely studied in the photocatalytic field due to their excellent light responsiveness. Among them, the potential and mechanism regarding photocatalytic degradation of organic pollutants by Bi2Fe4O9 are seriously ignored. In this research, Bi2Fe4O9/reduced graphene oxide (BFO/rGO) was successfully synthesized for tetracycline (TC) removal. Under visible light irradiation, the TC degradation efficiency reached 83.73% within 60 min, which was much higher than that of pure BFO or rGO. The impacts of crucial factors (TC initial concentration, humic acid concentration, pH value and inorganic anions) were systematically analyzed. The photoelectric performance experiments indicated that the addition of rGO decreased the electron-hole pair recombination efficiency and improved the charge transfer efficiency, thus significantly enhancing the photocatalytic performance. According to quenching experiments and EPR (Electron Paramagnetic Resonance) analysis, superoxide radical (•O2-) and hole (h+) were determined as the main active species during degradation reactions. Eventually, the possible degradation routes of TC were presented by identifying intermediates.

Recent advances in designing and developing efficient sillenite-based materials for photocatalytic applications

Sillenite materials have been the subject of intense investigation for recent years due to their unique characteristics. They possess a distinct structure with space group I23, allowing them to exhibit distinctive features, such as an electronic structure ideal for certain applications such as photocatalysis. The present research delves into the structure, synthesis, and properties of sillenites, highlighting their suitability for photocatalysis. It explores also advanced engineering strategies for designing sillenite-based photocatalysts, including heterojunction formation, morphology modification, doping, and hybrid processes. Each strategy offers advantages and limitations that are critically discussed. The review then lists and discusses the photocatalytic performance of various sillenite-based systems recently developed for common applications, such as removing hazardous organic and inorganic contaminants, and even infrequent applications, such as microbial inactivation, H2 generation, CO2 reduction and N2 fixation. Finally, valuable insights and suggestions are put forward for future research directions in the field of sillenite-based photocatalysis. This comprehensive overview would provide a valuable resource for the development of efficient photocatalytic systems to address environmental and energy challenges.

Photocatalytic fuel cell based on integrated silicon nanowire arrays/zinc oxide heterojunction anode for simultaneous wastewater treatment and electricity production

Photocatalytic fuel cells (PFCs) convert organic waste into electricity, thereby providing a potential solution for remediating environmental pollution and solving energy crises. Most PFCs for energy generation applications use powder photocatalysts, which have poor mechanical stability, high internal resistance, and may detach from the substrate during reactions, leading to unstable performance. Integrated photoelectrodes can overcome the drawbacks of powder catalysts. In this study, an integrated photoanode was prepared based on a silicon nanowire arrays/zinc oxide (Si NWs/ZnO) heterojunction by combining metal-assisted chemical etching (MACE) and hydrothermal methods. The resulting photoanode was used to assemble a PFC for simultaneous electricity generation and Rhodamine (RhB) dye wastewater degradation. This PFC showed excellent cell performance under irradiation, with a short-circuit current density of 0.183 Am-2, an open-circuit voltage (OCV) of 0.72 V, and a maximum power density of 0.87 W m-2. It could also be used continuously 20 times while degrading > 90% of RhB. This performance was ascribed to the three-dimensional (3D) structure and large surface area of Si NWs, as well as the matched band structure of ZnO, which facilitated the efficient separation and transport of photogenerated carriers in Si NWs/ZnO. The integrated structure also shortened the carrier transport pathways and suppressed carrier recombination. This research provides a foundation for the development of efficient, stable, low-cost, small-scale PFCs.

Highly flame-retardant materials of different divalent metal ions alginate/silver phosphate: Synthesis, characterizations, and synergistic phosphorus-polymetallic effects

Three kinds of divalent metal ions (Ca2+, Cu2+, Zn2+) alginate/silver phosphate (MAlg/Ag3PO4) hybrid materials were prepared via an in-situ method, and the composites were characterized by X-ray diffractometry (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and Fourier transform infrared spectrum (FTIR). To investigate their flame-retardant properties and phosphorus-polymetallic flame-retardant effects, the combustion behavior and flammability of the composites were assessed by using the thermogravimetric analysis (TGA), limiting oxygen index (LOI) and micro-calorimeter tests (MCC). The results show that the three composites were thermally stable, among which the LOI of CaAlg/Ag3PO4, CuAlg/Ag3PO4 and ZnAlg/Ag3PO4 were 62.6 %, 46.5 % and 79.8 %, respectively, which were much higher than the prescribed flame retardants which was 27 %. According to the TGA, the thermal stability was ZnAlg/Ag3PO4 > CaAlg/Ag3PO4 > CuAlg/Ag3PO4. The heat release capacity (HRC) of the above three materials was 49 J/(g·K), 69 J/(g·K), 41 J/(g·K), respectively, and the fire safety performance was also in the same order as the thermal stability. By using the thermogravimetric analysis coupled with Fourier transform infrared analysis (TG-FTIR) and pyrolysis-gas chromatography-mass spectrometry (Py-GC/MS), the flame retarding mechanism of MAlg/Ag3PO4 and the synergistic effect of Ag3PO4 and divalent metal ions were proposed based on the experimental data.

Dual-functional marine algal carbon-based materials with highly efficient dye removal and disinfection control

The design and simple, green preparation of dual-functional materials for the decontamination of both hazardous dyes and pathogenic microorganisms from wastewater remain challenging currently. Herein, a promising marine algal carbon-based material (named C-SA/SP) with both highly efficient dye adsorptive and antibacterial properties was fabricated based on the incorporation of sodium alginate and a low dose of silver phosphate via a facile and eco-friendly approach. The structure, removal of malachite green (MG) and congo red (CR), and their antibacterial performance were studied, and the adsorption mechanism was further interpreted by the statistical physics models, besides the classic models. The results show that the maximum simulated adsorption capacity for MG reached 2798.27 mg/g, and its minimal inhibit concentration for Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) was 0.4 mg/mL and 0.2 mg/mL, respectively. The mechanistic study suggests that silver phosphate exerted the effects of catalytic carbon formation and pore formation, while reducing the electronegativity of the material as well, thus improving its dye adsorptive performance. Moreover, the MG adsorption onto C-SA/SP showed vertical orientation and a multi-molecular way, and its adsorption sites were involved in the adsorption process with the increase of temperature. Overall, the study indicates that the as-made dual-functional materials have good applied prospects for water remediation.

A novel iron molybdate photocatalyst with heterojunction-like band gap structure for organic pollutant degradation by activation of persulfate under simulated sunlight irradiation

Advanced oxidation processes (AOPs) applied to wastewater treatment have become increasingly well developed and the ability of a single technology to remove difficult organic pollutants is limited. One of the main limiting factors is the insufficient variety and quantity of active species generated during the reaction process and catalyst failure. The coupling of the two methods is a practical and effective approach. In this study, different types of semiconductor persulfate (PS) activators, iron molybdate nanoparticles (I-FeMoO₄, II-FeMoO₄, and III-FeMoO₄), were synthesized by simple solvothermal and calcination methods and applied to photo-assisted activation of PS systems. In addition, the relationship between the intrinsic physicochemical and optoelectronic properties of FeMoO₄ and the catalytic degradation performance was revealed by a series of characterization tools, and the dominant catalysts were screened. At an unadjusted pH of 4.86, 0.6 g L^-1 of PS and 0.4 g L^-1 of I-FeMoO₄ could achieve efficient degradation of several difficult organic dye contaminants (rhodamine b (Rh B), methylene blue (MB), malachite green (MG), methyl orange (MO), and tartrazine (TTZ)) and other antibiotic contaminants (sulfamethoxazole (SMX), tetracycline (TC), norfloxacin (NOR), and carbamazepine (CBZ)) within 5-60 min. Possible degradation mechanisms in the I-FeMoO₄/PS/Light reaction system were suggested by radical trapping experiments and electron paramagnetic resonance (EPR) tests. Recovery tests demonstrated that I-FeMoO₄ has good recoverable stability and did not cause secondary pollution. Finally, our study provided a new perspective on the application of coupled wastewater treatment technologies in the practical treatment of organic wastewater.

A novel S-scheme Ws2/BiYWO6 electrostatic heterostructure for enhanced photocatalytic degradation performance towards the degradation of Rhodamine B

Constructing S-scheme heterojunction between two semiconductor materials is an effective route to increase the photocatalytic degradation efficiency. Here, a novel S-scheme WS₂/BiYWO₆ heterojunction photocatalyst was prepared by wet chemical route. At the same time, the photocatalytic degradation performance of the fabricated materials was analyzed by the degradation of Rhodamine B under visible light. Of all prepared WS₂/BiYWO₆ composites, the 20 wt.% WS₂ loaded WS₂/BiYWO₆ composite exhibited an enhanced photocatalytic degradation ability than other prepared photocatalysts. Here, O₂^·- and ^·OH radicals are performing a pivotal role in the Rhodamine B degradation and the optimized composite shows greater photocurrent intensity than pure BiYWO₆ and WS₂, respectively. Also, the synthesized photocatalyst maintains its stability with negligible changes even after three cycles. Thereby, the constructed S-scheme WS₂/BiYWO₆ heterojunction is a potential material for the wastewater remediation.

Graphene oxide-incorporated silver-based photocatalysts for enhanced degradation of organic toxins: a review

Environmental contamination and scarcity of energy have been deepening over the last few decades. Heterogeneous photocatalysis plays a prominent role in environmental remediation. The failure of earlier metal oxide systems like pure TiO₂ and ZnO as stable visible-light photocatalysts demanded more stable catalysts with high photodegradation efficiency. Silver-based semiconductor materials gained popularity as visible-light-responsive photocatalysts with a narrow bandgap. But their large-scale usage in natural water bodies for organic contaminant removal is minimal. The factors like self-photocorrosion and their slight solubility in water have prevented the commercial use. Various efforts have been made to improve their photocatalytic activity. This review focuses on those studies in which silver-based semiconductor materials are integrated with carbonaceous graphene oxide (GO) and reduced graphene oxide (RGO). The decoration of Ag-based semiconductor components on graphene oxide having high-surface area results in binary composites with enhanced visible-light photocatalytic activity and stability. It is found that the introduction of new efficient materials further increases the effectiveness of the system. So binary and ternary composites of GO and Ag-based materials are reviewed in this paper.

Construction of Ag nanocluster-modified Ag3PO4 containing silver vacancies via in-situ reduction: With enhancing the photocatalytic degradation activity of sulfamethoxazole

Photocatalytic removal of sulfonamide antibiotics is an effective strategy to solve environmental pollution. Ag3PO4 is a promising anode material for photocatalytic material with photocatalytic degradation ability under ultraviolet light or natural light. Unfortunately, due to its instability, Ag+ could be reduced to Ag0 which loaded onto the surface of Ag3PO4 during the photocatalytic process, causing self-photocorrosion and resulting in the reduction of photocatalytic activity and stability. Herein, Ag3PO4 nanoparticles loaded with Ag nanoclusters containing Ag vacancies (Ag/Ag3PO4-VAg) were constructed by an in-situ reduction strategy to achieve effectively photocatalytic degradation behavior. The Ag nanoclusters loaded on the surface of Ag3PO4 can not only effectively inhibit the self-photocorrosion but also affords a localized surface plasmon resonance (LSPR) effect in the photocatalytic process, thus leading to the efficient generation and rapid transfer of photogenerated carriers behavior. In addition, the Ag vacancies in Ag3PO4 are crucial to increasing the adsorption energy of H2O for further enhancing the capture and accumulation of electrons. In detail, according to Zeta potential analysis, the strong adsorption sites of sulfamethoxazole (SMX) molecules are generated at the interface of Ag and Ag3PO4, which promote the activation of SMX molecules. A 100 ml of 20 mg/L SMX could be completely degraded within 15 min with an apparent rate constant (Kapp) of 0.306 min-1, which far exceeds the activity of most of the photocatalysts. This work may provide an attractive strategy to address the activity, stability of Ag3PO4 and and realizing the green remediation of SMX wastewater.

Simple Low Temperature Technique to Synthesize Sillenite Bismuth Ferrite with Promising Photocatalytic Performance

Sillenite-type members of the bismuth ferrite family have demonstrated outstanding potential as novel photocatalysts in environmental remediation such as organic pollutant degradation. This investigation has developed a low temperature one-step hydrothermal technique to fabricate sillenite bismuth ferrite Bi₂₅FeO₄₀ (S-BFO) via co-substitution of 10% Gd and 10% Cr in Bi and Fe sites of BiFeO₃, respectively, by tuning hydrothermal reaction temperatures. Rietveld refined X-ray diffraction patterns of the as-synthesized powder materials revealed the formation of S-BFO at a reaction temperature of 120-160 °C. A further increase in the reaction temperature destroyed the desired sillenite structure. With the increase in the reaction temperature from 120 to 160 °C, the morphology of S-BFO gradually changed from irregular shape to spherical powder nanomaterials. The high-resolution TEM imaging demonstrated the polycrystalline nature of the S-BFO(160) nanopowders synthesized at 160 °C. The as-synthesized samples exhibited considerably high absorbance in the visible region of the solar spectrum, with the lowest band gap of 1.76 eV for the sample S-BFO(160). Interestingly, S-BFO(160) exhibited the highest photocatalytic performance under solar irradiation, toward the degradation of rhodamine B and methylene blue dyes owing to homogeneous phase distribution, regular powder-like morphology, lowest band gap, and quenching of electron-hole pair recombination. The photodegradation of a colorless organic pollutant (ciprofloxacin) was also examined to ensure that the degradation is photocatalytic and not dye-sensitized. In summary, Gd and Cr co-doping have proven to be a compelling energy-saving and low-cost approach for the formulation of sillenite-phase bismuth ferrite with promising photocatalytic activity.

Fabrication of Ag3PO4/polyaniline-activated biochar photocatalyst for efficient triclosan degradation process and toxicity assessment

Triclosan (TCS) is a typical environmental pollutant, which seriously threatens the health of humans and organisms. A novel strategy of biochar/Ag₃PO₄/polyaniline (PANI) composite photocatalyst was synthesized by a facile chemical precipitation method to efficiently degrade TCS. XRD, Raman, ESR, etc. were used to reveal the effective associations among physiochemistry, photochemistry and photocatalytic properties of the composite. It was proved the synergistic effects of biochar (T-Bio) and PANI resulted in the decrease of Ag₃PO₄ particle size, the enhancement of adsorption, the improvement of light utilization, the increase of photogenerated carrier separation and the promotion of reactive species. The photocatalytic mechanism showed h⁺ was the main active species, O₂^- and OH played minor roles. Under the irradiation of visible light, the optimal photocatalyst (1.0% T-Bio/AP/1.0% PANI) displayed excellent photocatalytic activity with the removal rate of 85.21% for TCS within 10 min, and the apparent rate constant K' was 2.38 times of Ag₃PO₄. 11 main intermediates for TCS degradation were identified, and their toxicity was significantly reduced. The possible degradation pathways were proposed. This work is the first systematic study on the degradation behavior of TCS by Ag₃PO₄-based photocatalyst, and it provides a new approach to fabricate photocatalysts with synergistic effects and amazing photocatalytic activity by biochar.

Broccoli-liked silver phosphate nanoparticles supported on green nanofiber membrane for visible-light driven photodegradation towards water pollutants

In view of the practical application, it is imperative to develop efficient, exercisable, and visible light driven water pollution treatment materials. Herein, a high-efficiency green photocatalytic membrane for water pollution treatment is proposed and fabricated conveniently. Firstly, silver phosphate (Ag₃PO₄) nanoparticles with controlled morphology were prepared by simple liquid-phase precipitation method, and then a hierarchical structured Ag₃PO₄@polylactic acid (PLA) composite nanofiber membrane was prepared by electrospinning. Using electrospun PLA nanofiber membrane as a carrier of photocatalysts can significantly improve the dispersion of Ag₃PO₄nanoparticles, and increase the contact probability with pollutants and photocatalytic activity. The prepared PLA@Ag₃PO₄composite membrane was used to degrade methylene blue (MB) and tetracycline hydrochloride (TC) under visible light irradiation. The results showed that the removal ratio of pollutants on Ag₃PO₄@PLA composite nanofiber membrane was 94.0% for MB and 82.0% for TC, demonstrating an outstanding photocatalytic activity of composite membrane. Moreover, the PLA nanofiber membrane is a self-supported and biodegradable matrix. After five cycles, it can still achieve 88.0% of the initial photocatalytic degradation rate towards MB, showing excellent recyclability. Thus, this composite nanofiber membrane is a high-efficiency and environmental-friendly visible light driven water pollution treatment material that could be used in real applications.

Design of Z-scheme g-C3N4/BC/Bi25FeO40 photocatalyst with unique electron transfer channels for efficient degradation of tetracycline hydrochloride waste

High electron transfer rates and a higher number of electron transfer active sites play important roles in inhibiting the recombination of photogenerated electron-hole pairs. In the experiments described in this article, the g-C₃N₄/BC/Bi₂₅FeO₄₀ composite material was prepared to use biochar (BC) as the conductive channel. The presence of BC significantly increases the electron transfer rate due to its excellent electrical conductivity and can provide more electron transfer active sites. At the same time, BC provides a larger surface area and has a loose porous structure, which lead to excellent adsorption performance. Based on various characterization results, it was confirmed that the Z-scheme heterojunction was successfully constructed between g-C₃N₄ and Bi₂₅FeO₄₀. The photocatalytic experiment results showed that the degradation efficiency of g-C₃N₄/BC/Bi₂₅FeO₄₀ on the tetracycline hydrochloride (TCH) could reach 92.2% within 60 min. Parameters such as circulation stability, pH value of the solution and the amount of composite materials were studied. The synthesized composite material has good reusability and high efficiency in a wide pH range of 3-11. Its excellent photocatalytic activity is attributed to the formation of an effective Z-scheme heterostructure, as well as the rapid photoelectron transfer and excellent adsorption capacity of BC. This work provides a way to design new photocatalysts using semiconductor composite materials and BC materials.

Carbamazepine degradation by visible-light-driven photocatalyst Ag3PO4/GO: Mechanism and pathway

Carbamazepine (CBZ), as one of the most frequently detected pharmaceuticals, is of great concern due to its potential impact on the ecosystem and human health. This study provides an effective approach to remove CBZ by using photocatalyst silver phosphate combined with graphene oxide (Ag3PO4/GO) under visible irradiation. The morphology, composition, and optical properties of Ag3PO4/GO were characterized employing SEM, XRD, and DRS. Graphene oxide could improve the visible-light utilization and promote electron's charge to enhance the photocatalytic performance of Ag3PO4/GO. With the optimal reaction condition of 5.86 mW/cm2 light intensity, 15-25 °C temperature, 5-7 pH, and 0.5 mg/L catalytic dosages, 5 mg/L CBZ could be completely degraded in 30 min, and the apparent rate constant could reach 0.12 min-1. Additionally, the radical trapping experiments indicated •OH and O2-• were the main reactive oxygen species employed to eliminate CBZ. The decay pathways of CBZ had been proposed accordingly, and the main product was the low-molecular products.

Interfacial engineering in 3D/2D and 1D/2D bismuth ferrite (BiFeO3)/Graphene oxide nanocomposites for the enhanced photocatalytic activities under sunlight

3D-particulate and 1D-fiber structures of multiferroic bismuth ferrite (BiFeO₃/BFO) and their composites with 2D-graphene oxide (GO) have been developed to exploit the different scheme of interfacial engineering as 3D/2D and 1D/2D systems. Particulates and fibers of BFO were developed via sol-gel and electrospinning fabrication approaches respectively and their integration with GO was performed via the ultrasonic-assisted chemical reduction process. The crystalline and phase formation of BiFeO₃ and GO was confirmed from the XRD patterns obtained. The electron microscopic images revealed the characteristic integration of 3D particulates (with average size of 100 nm) and 1D fibers (with diameter of ~150 nm and few μm length) onto the 2D GO layers (thickness of ~27 nm). XPS analysis revealed that the BFO nanostructures have been integrated onto the GO through chemisorptions process, where it indicated that the ultrasonic process engineers the interface through the chemical modification of the surface of these 3D/2D and 1D/2D nanostructures. The photophysical studies such as the impedance and photocurrent measurements showed that the charge separation and recombination resistance is significantly enhanced in the system, which can directly be attributed to the effective interfacial engineering in the developed hetero-morphological composites. The degradation studies against a model pollutant Rhodamine B revealed that the developed nanocomposites exhibit superior photocatalytic activity via the effective generation of OH radicals as confirmed by the radical analysis studies (100% degradation in 150 and 90 min for 15% GO/BFO particulate and fiber composites, respectively). The developed system also demonstrated excellent photocatalytic recyclability, indicated their enhanced stability.

Fabrication of novel AgVO3/BiOI nanocomposite photocatalyst with photoelectrochemical activity towards the degradation of Rhodamine B under visible light irradiation

In the present work, a visible light driven AgVO₃/BiOI nanocomposite photocatalyst with different wt % (1, 2, 3) of AgVO₃ was fabricated by using facile hydrothermal method. Further, the nanocomposite was characterized by FT-IR, XRD, SEM, TEM, EDS, UV-vis DRS, photoluminescence and photoelectrochemical studies. The structural characterization showed nanorods on nanosheet surface. Among different AgVO₃ loaded samples, the photocatalytic efficiency of 1 wt % AgVO₃/BiOI nanocomposite was found to be comparatively higher than the pure BiOI and AgVO₃. The photodegradation rate constant values of pure BiOI, AgVO₃ and 1, 2, 3 wt % AgVO₃/BiOI nanocomposites are 0.006, 0.0033, 0.0255, 0.01575, 0.0116 min^-1 respectively. This enhanced photocatalytic activity was due to the increasing visible light absorption ability and efficient separation of the charge carriers. Thereby, the 1 wt % AgVO₃/BiOI nanocomposite photocatalyst exhibited increased photodegradation activity, photostability and recyclability characteristics. The radical trapping experiment confirmed the role of OH and h⁺ in the photocatalytic degradation of RhB. Based on this, the probable mechanism of degradation of RhB under visible light irradiation has also been proposed. Hence, we believe it could be a promising material that can be employed for the photodegradation of organic pollutants present in wastewater.

In-situ synthesis of CuS@carbon nanocomposites and application in enhanced photo-fenton degradation of 2,4-DCP

Novel CuS nanoparticles embedded into carbon nanosheets (CuS@CNs) were prepared in situ by applying wheat straw cellulose/feather protein hydrogel beads as templates and were used to photocatalytically activate H₂O₂ to degrade 2,4-dichlorphenol (2,4-DCP). The photo-Fenton catalytic properties of the nanocomposite catalysts obtained under different synthetic conditions, including different Cu²⁺ concentrations, S^2- concentrations and calcination temperatures, were evaluated. The results showed that CuS@CNs with 0.1 M Cu²⁺, 0.1 M S^2- at 800 °C presented excellent photo-Fenton degradation performance for 2,4-DCP (25 mg/L) in the presence of H₂O₂ and could remove 90% of 2,4-DCP in 2.5 h. The water quality parameters (pH, Cl^-, HCO₃^-, H₂PO₄^- and SO₄^2-) exhibited different effects on the photocatalytic degradation process. The catalytic activity of the CuS@CNs used in the cycle could be recovered after thermal regeneration. Radical quenching and electron paramagnetic resonance (EPR) experiments confirmed that ·OH species were main active radicals contributing to the degradation of 2,4-DCP. The photocatalytic mechanism of CuS@CNs was also explored by photoelectrochemical (PEC) measurements and UV-vis diffuse reflectance spectroscopy (DRS). Incorporation of carbon nanosheets could significantly improve the separation of photogenerated charge carriers to stimulate pollutant degradation by CuS. Based on the detected intermediates, the degradation pathway of 2,4-DCP in the CuS@CNs/H₂O₂ reaction system was also proposed.

Agro-waste extracted cellulose supported silver phosphate nanostructures as a green photocatalyst for improved photodegradation of RhB dye and industrial fertilizer effluents

The efficiency and reusability of photocatalysts are the dominant factors for their pragmatic use. The visible light induced semiconductor silver phosphate is a superior photocatalyst effective under visible light but its stability is still an undiscussed issue. To overcome this stability issue in this present manuscript, eco-friendly agro-waste extracted cellulose supported silver phosphate nanostructures have been designed for the first time through a simple chemical process. At first, silver phosphate nanostructures were synthesized by the co-precipitation method. Then, different weights of cellulose were added to the silver nitrate solution to form cellulose supported silver phosphate nanostructures. The photodegradation efficiency for each weight ratio was examined in which the photocatalyst Ag-8 nanostructures showed a high rate (0.024 min^-1) for degradation of Rhodamine B (RhB) using a low intensity tungsten bulb. Real sample analysis has also been carried out using this photocatalyst for the degradation of industrial fertilizer effluents. The degradation rate of all the nanostructures was found to be high in comparison to pristine silver phosphate as well as the extracted bare cellulose. The photocatalytic activity is enhanced because of the participation of cellulose as a support which makes an interface for silver phosphate and assists it in delaying the charge recombination period under visible light. To understand the photochemical reaction of electrons and holes, scavenger studies were also performed.

Octadecylamine degradation through catalytic activation of peroxymonosulfate by FeMn layered double hydroxide

A kind of heterogeneous catalyst, FeMn layered double hydroxide (Fe-Mn-LDH), was fabricated by coprecipitation process and used as PMS activator to degrade a novel organic pollutant octadecylamine (ODA). And the X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microcopy (TEM), Mapping and X-ray photoelectron spectra (XPS) measurements were utilized to characterize the fresh and used Fe-Mn-LDH. After a serious of degradation experiments, it was clearly to see that the activator possessed excellent activation property for PMS and was capable of removing 85% ODA (10 mg·L^-1) within 25 min obviously higher than pure PMS. Moreover, the effect of some elements (such as PMS consumption, catalyst consistence and initial pH value), different reaction system and catalyst repeatability on ODA degradation were also explored. And by identification of main radical experiment, SO₄^- and HO were both confirmed the primary radicals. What's more, extra anion and nature organic matter (NOM) addition experiment displayed that NOM, NO₃^- and CO₃^2- perform a negative effect on ODA degradation but Cl^- could promote it. In addition, repeated experiments and metal leaching after degradation showed good stability of Fe-Mn-LDH. Finally, based on the XPS and Gas Chromatography-Mass Spectrometer (GS-MS) technology, the possible degradation mechanism and pathway were proposed.

A facile heterogeneous system for persulfate activation by CuFe2O4 under LED light irradiation

In this study, the removal performance for rhodamine B (RB) by persulfate (PS) activated by the CuFe2O4 catalyst in a heterogeneous catalytic system under LED light irradiation was investigated. The effect of vital experimental factors, including initial solution pH, CuFe2O4 dosage, PS concentration, co-existing anion and initial RB concentration on the removal of RB was systematically studied. The removal of RB was in accordance with the pseudo first-order reaction kinetics. Over 96% of 20 mg L-1 RB was removed in 60 min using 0.5 g L-1 CuFe2O4 catalyst and 0.2 mM PS at neutral pH. In addition, free radical quenching experiments and electron spin resonance (EPR) experiments were performed, which demonstrated the dominant role of sulfate radical, photogenerated holes and superoxide radical in the CuFe2O4/PS/LED system. The morphology and physicochemical properties of the catalyst were characterized by XRD, SEM-EDS, TEM, N2 adsorption-desorption isotherm, UV-vis DRS, and XPS measurements. Moreover, 18.23% and 38.79% total organic carbon (TOC) removal efficiency was reached in 30 min and 60 min, respectively. The catalyst revealed good performance during the reusability experiments with limited iron and copper leaching. Eventually, the major intermediates in the reaction were detected by GC/MS, and the possible photocatalytic pathway for the degradation of RB in the CuFe2O4/PS/LED system was proposed. The results suggest that the CuFe2O4/PS/LED system has good application for further wastewater treatment.

Facile Synthesis of a Polycatenane Compound Based on Ag-triazole Complexes and Phosphomolybdic Acid for the Catalytic Epoxidation of Olefins with Molecular Oxygen

A simple and efficient approach was developed for synthesizing a metal-organic polycatenated compound composed of Ag-triazole complexes and phosphomolybdic acid (PMA) clusters. The hybrid compound, namely {[Ag2(trz)2] [Ag24(trz)18]}[PMo12O40]2 (1) (trz = 1,2,4-triazole), showed high catalytic activity, selectivity and recyclability for the epoxidation of olefins with molecular oxygen as the oxidant and isobutyraldehyde as the co-reagent, and could even work well under ambient conditions. The special polycatenane framework, formed by interlocking [Ag24(trz)18]6+ nanocages, provides suitable space for filling the PMA clusters. The existence of multi-interactions, including π-π stacking, Ag-Ag interactions, and electrostatic interactions, should play a determinative role in fabricating the catalytically active and stable PMA-based polycatenane catalyst for aerobic epoxidation of olefins.