Characterization of DNA hybridization kinetics in a microfluidic flow channel

Electric-field assisted silicon nanowire field effect transistor for the ultra-low concentration nucleic acid detection

Ultra-low concentration nucleic acid detection is crucial for disease diagnosis and prognosis. Silicon nanowire field-effect transistors (SiNW FETs) are promising due to their sensitivity, real-time capabilities, and compact design. A critical consideration for FETs is the reaction time required for nucleic acid diffusion to the detection surface, especially at low concentrations. This study utilizes polycrystalline silicon nanowire FETs (poly-SiNW FETs) as biosensors, employing a negative voltage on the liquid gate used for detection to create an electric field. This field accelerates nucleic acid diffusion towards the sensor surface to interact with immobilized probes. We adjusted the gate voltages and target solution injection flow rates to identify optimal parameters for nucleic acid detection and how the electrical field accelerates hybridization kinetics. We varied the probe immobilization times to show that higher ligand density accelerates the interaction with the immobilized probe. The study demonstrated stable diffusion of target DNA by combining FET with an electric field of -1 V and a slow injection flow rate, reducing the equilibrium time from 60 to 20 min. Additional improvement was achieved by enhancing probe immobilization density and applying an electric field, resulting in a faster probe-target hybridization reaction rate. These efforts significantly improved the signal to maintain superior performance and reduced the time required to reach equilibrium. This research pioneers using an external electric field to expedite detection time in field-effect transistors, demonstrating the potential for accelerated nucleic acid detection in nanowire FETs.

Reversible bonding of microfluidics: Review and applications

With the development of microfluidic technology, new materials and fabrication methods have been constantly invented in the field of microfluidics. Bonding is one of the key steps for the fabrication of enclosed-channel microfluidic chips, which have been extensively explored by researchers globally. The main purpose of bonding is to seal/enclose fabricated microchannels for subsequent fluid manipulations. Conventional bonding methods are usually irreversible, and the forced detachment of the substrate and cover plate may lead to structural damage to the chip. Some of the current microfluidic applications require reversible bonding to reuse the chip or retrieve the contents inside the chip. Therefore, it is essential to develop reversible bonding methods to meet the requirements of various applications. This review introduces the most recent developments in reversible bonding methods in microfluidics and their corresponding applications. Finally, the perspective and outlook of reversible bonding technology were discussed in this review.

Amplification-free electrochemical biosensor detection of circulating microRNA to identify drug-induced liver injury

Drug-induced liver injury (DILI) is a major challenge in clinical medicine and drug development. There is a need for rapid diagnostic tests, ideally at point-of-care. MicroRNA 122 (miR-122) is an early biomarker for DILI which is reported to increase in the blood before standard-of-care markers such as alanine aminotransferase activity. We developed an electrochemical biosensor for diagnosis of DILI by detecting miR-122 from clinical samples. We used electrochemical impedance spectroscopy (EIS) for direct, amplification free detection of miR-122 with screen-printed electrodes functionalised with sequence specific peptide nucleic acid (PNA) probes. We studied the probe functionalisation using atomic force microscopy and performed elemental and electrochemical characterisations. To enhance the assay performance and minimise sample volume requirements, we designed and characterised a closed-loop microfluidic system. We presented the EIS assay's specificity for wild-type miR-122 over non-complementary and single nucleotide mismatch targets. We successfully demonstrated a detection limit of 50 pM for miR-122. Assay performance could be extended to real samples; it displayed high selectivity for liver (miR-122 high) comparing to kidney (miR-122 low) derived samples extracted from murine tissue. Finally, we successfully performed an evaluation with 26 clinical samples. Using EIS, DILI patients were distinguished from healthy controls with a ROC-AUC of 0.77, a comparable performance to qPCR detection of miR-122 (ROC-AUC: 0.83). In conclusion, direct, amplification free detection of miR-122 using EIS was achievable at clinically relevant concentrations and in clinical samples. Future work will focus on realising a full sample-to-answer system which can be deployed for point-of-care testing.

Toward the Development of Rapid, Specific, and Sensitive Microfluidic Sensors: A Comprehensive Device Blueprint

Recent advances in nano/microfluidics have led to the miniaturization of surface-based chemical and biochemical sensors, with applications ranging from environmental monitoring to disease diagnostics. These systems rely on the detection of analytes flowing in a liquid sample, by exploiting their innate nature to react with specific receptors immobilized on the microchannel walls. The efficiency of these systems is defined by the cumulative effect of analyte detection speed, sensitivity, and specificity. In this perspective, we provide a fresh outlook on the use of important parameters obtained from well-characterized analytical models, by connecting the mass transport and reaction limits with the experimentally attainable limits of analyte detection efficiency. Specifically, we breakdown when and how the operational (e.g., flow rates, channel geometries, mode of detection, etc.) and molecular (e.g., receptor affinity and functionality) variables can be tailored to enhance the analyte detection time, analytical specificity, and sensitivity of the system (i.e., limit of detection). Finally, we present a simple yet cohesive blueprint for the development of high-efficiency surface-based microfluidic sensors for rapid, sensitive, and specific detection of chemical and biochemical analytes, pertinent to a variety of applications.

Nucleic Acid Tests for Clinical Translation

Nucleic acids, including deoxyribonucleic acid (DNA) and ribonucleic acid (RNA), are natural biopolymers composed of nucleotides that store, transmit, and express genetic information. Overexpressed or underexpressed as well as mutated nucleic acids have been implicated in many diseases. Therefore, nucleic acid tests (NATs) are extremely important. Inspired by intracellular DNA replication and RNA transcription, in vitro NATs have been extensively developed to improve the detection specificity, sensitivity, and simplicity. The principles of NATs can be in general classified into three categories: nucleic acid hybridization, thermal-cycle or isothermal amplification, and signal amplification. Driven by pressing needs in clinical diagnosis and prevention of infectious diseases, NATs have evolved to be a rapidly advancing field. During the past ten years, an explosive increase of research interest in both basic research and clinical translation has been witnessed. In this review, we aim to provide comprehensive coverage of the progress to analyze nucleic acids, use nucleic acids as recognition probes, construct detection devices based on nucleic acids, and utilize nucleic acids in clinical diagnosis and other important fields. We also discuss the new frontiers in the field and the challenges to be addressed.

An automated microfluidic DNA microarray platform for genetic variant detection in inherited arrhythmic diseases

In this study, we developed an automated microfluidic DNA microarray (AMDM) platform for point mutation detection of genetic variants in inherited arrhythmic diseases. The platform allows for automated and programmable reagent sequencing under precise conditions of hybridization flow and temperature control. It is composed of a commercial microfluidic control system, a microfluidic microarray device, and a temperature control unit. The automated and rapid hybridization process can be performed in the AMDM platform using Cy3 labeled oligonucleotide exons of SCN5A genetic DNA, which produces proteins associated with sodium channels abundant in the heart (cardiac) muscle cells. We then introduce a graphene oxide (GO)-assisted DNA microarray hybridization protocol to enable point mutation detection. In this protocol, a GO solution is added after the staining step to quench dyes bound to single-stranded DNA or non-perfectly matched DNA, which can improve point mutation specificity. As proof-of-concept we extracted the wild-type and mutant of exon 12 and exon 17 of SCN5A genetic DNA from patients with long QT syndrome or Brugada syndrome by touchdown PCR and performed a successful point mutation discrimination in the AMDM platform. Overall, the AMDM platform can greatly reduce laborious and time-consuming hybridization steps and prevent potential contamination. Furthermore, by introducing the reciprocating flow into the microchannel during the hybridization process, the total assay time can be reduced to 3 hours, which is 6 times faster than the conventional DNA microarray. Given the automatic assay operation, shorter assay time, and high point mutation discrimination, we believe that the AMDM platform has potential for low-cost, rapid and sensitive genetic testing in a simple and user-friendly manner, which may benefit gene screening in medical practice.

Straightforward Micropatterning of Oligonucleotides in Microfluidics by Novel Spin-On ZrO₂ Surfaces

DNA biochip assays often require immobilization of bioactive molecules on solid surfaces. A simple biofunctionalization protocol and precise spatial binding represent the two major challenges in order to obtain localized region specific biopatterns into lab-on-a-chip (LOC) systems. In this work, a simple strategy to anchor oligonucleotides on microstructured areas and integrate the biomolecules patterns within microfluidic channels is reported. A photosensitive ZrO2 system is proposed as an advanced platform and versatile interface for specific positioning and oriented immobilization of phosphorylated DNA. ZrO2 sol-gel structures were easily produced on fused silica by direct UV lithography, allowing a simple and fast patterning process with different geometries. A thermal treatment at 800 °C was performed to crystallize the structures and maximize the affinity of DNA to ZrO2. Fluorescent DNA strands were selectively immobilized on the crystalline patterns inside polydimethylsiloxane (PDMS) microchannels, allowing high specificity and rapid hybridization kinetics. Hybridization tests confirmed the correct probe anchoring and the bioactivity retention, while denaturation experiments demonstrated the possibility of regenerating the surface.

Biofunctionalized nanoslits for wash-free and spatially resolved real-time sensing with full target capture

We propose biofunctionalized nanofluidic slits (nanoslits) as an effective platform for real-time fluorescence-based biosensing in a reaction-limited regime with optimized target capture efficiency. This is achieved by the drastic reduction of the diffusion length, thereby a boosted collision frequency between the target analytes and the sensor, and the size reduction of the sensing element down to the channel height comparable to the depletion layer caused by the reaction. Hybridization experiments conducted in DNA-functionalized nanoslits demonstrate the analyte depletion and the wash-free detection ∼10 times faster compared to the best microfluidic sensing platforms. The signal to background fluorescence ratio is drastically increased at lower target concentrations, in favor of low-copy number analyte analysis. Experimental and simulation results further show that biofunctionalized nanoslits provide a simple means to study reaction kinetics at the single-pixel level using conventional fluorescence microscopy with reduced optical depth.

DNA hybridization on silicon nanowire platform prepared by glancing angle deposition and metal assisted chemical etching process

Porous nanowire surface provides high capacity for oligonucleotide hybridization.

A controlled microfluidic electrochemical lab-on-a-chip for label-free diffusion-restricted DNA hybridization analysis

Lab-on-a-chip (LOC) devices for electrochemical analysis of DNA hybridization events offer a technology for real-time and label-free assessment of biomarkers at the point-of-care. Here, we present a microfluidic LOC, with 3 × 3 arrayed electrochemical sensors for the analysis of DNA hybridization events. A new dual layer microfluidic valved manipulation system is integrated providing controlled and automated capabilities for high throughput analysis. This feature improves the repeatability, accuracy, and overall sensing performance (Fig. 1). The electrochemical activity of the fabricated microfluidic device is validated and demonstrated repeatable and reversible Nernstian characteristics. System design required detailed analysis of energy storage and dissipation as our sensing modeling involves diffusion-related electrochemical impedance spectroscopy. The effect of DNA hybridization on the calculated charge transfer resistance and the diffusional resistance components is evaluated. We demonstrate a specific device with an average cross-reactivity value of 27.5%. The device yields semilogarithmic dose response and enables a theoretical detection limit of 1 nM of complementary ssDNA target. This limit is lower than our previously reported non-valved device by 74% due to on-chip valve integration providing controlled and accurate assay capabilities.

Electro-osmosis of electrorheological fluids

Electrorheological fluids are suspensions that are characterized by a strong functional dependence of the constitutive behavior of the fluids on the electric field. In this work, we consider electro-osmosis of an electrorheological fluid through a channel where a transverse, nonuniform electric field is spontaneously induced due to the presence of an electric double layer that is manifested due to surface charge density at the channel wall. We reveal a nonlinear interplay between the applied electric field, the induced electric field, and the observed flow profiles, which is fundamentally distinctive from other types of nonlinear electrokinetic effects that have been extensively discussed in the literature, in a sense that here an interaction between the applied electric field, the induced electric field, and the dependence of the rheology on the resultant electric field happens to be the focal source of nonlinearity in the observed phenomena. We analyze the electro-osmotic flow control through the exploitation of a combined nonlinear interplay of the driving electrokinetic forces and the resistive viscous interactions, which gives rise to distinctive flow regimes as compared to those realized in cases of either Newtonian fluids or non-Newtonian fluids having electric-field-independent flow rheology.

Transient convection, diffusion, and adsorption in surface-based biosensors

This paper presents a theoretical and computational investigation of convection, diffusion, and adsorption in surface-based biosensors. In particular, we study the transport dynamics in a model geometry of a surface plasmon resonance (SPR) sensor. The work, however, is equally relevant for other microfluidic surface-based biosensors, operating under flow conditions. A widely adopted approximate quasi-steady theory to capture convective and diffusive mass transport is reviewed, and an analytical solution is presented. An expression of the Damköhler number is derived in terms of the nondimensional adsorption coefficient (Biot number), the nondimensional flow rate (Péclet number), and the model geometry. Transient dynamics is investigated, and we quantify the error of using the quasi-steady-state assumption for experimental data fitting in both kinetically limited and convection-diffusion-limited regimes for irreversible adsorption, in specific. The results clarify the conditions under which the quasi-steady theory is reliable or not. In extension to the well-known fact that the range of validity is altered under convection-diffusion-limited conditions, we show how also the ratio of the inlet concentration to the maximum surface capacity is critical for reliable use of the quasi-steady theory. Finally, our results provide users of surface-based biosensors with a tool for correcting experimentally obtained adsorption rate constants.

HistoFlex--a microfluidic device providing uniform flow conditions enabling highly sensitive, reproducible and quantitative in situ hybridizations

A microfluidic device (the HistoFlex) designed to perform and monitor molecular biological assays under dynamic flow conditions on microscope slide-substrates, with special emphasis on analyzing histological tissue sections, is presented. Microscope slides were reversibly sealed onto a cast polydimethylsiloxane (PDMS) insert, patterned with distribution channels and reaction chambers. Topology optimization was used to design reaction chambers with uniform flow conditions. The HistoFlex provided uniform hybridization conditions, across the reaction chamber, as determined by hybridization to microscope slides of spotted DNA microarrays when applying probe concentrations generally used in in situ hybridization (ISH) assays. The HistoFlex's novel ability in online monitoring of an in situ hybridization assay was demonstrated using direct fluorescent detection of hybridization to 18S rRNA. Tissue sections were not visually damaged during assaying, which enabled adapting a complete ISH assay for detection of microRNAs (miRNA). The effects of flow based incubations on hybridization, antibody incubation and Tyramide Signal Amplification (TSA) steps were investigated upon adapting the ISH assay for performing in the HistoFlex. The hybridization step was significantly enhanced using flow based incubations due to improved hybridization efficiency. The HistoFlex device enabled a fast miRNA ISH assay (3 hours) which provided higher hybridization signal intensity compared to using conventional techniques (5 h 40 min). We further demonstrate that the improved hybridization efficiency using the HistoFlex permits more complex assays e.g. those comprising sequential hybridization and detection of two miRNAs to be performed with significantly increased sensitivity. The HistoFlex provides a new histological analysis platform that will allow multiple and sequential assays to be performed under their individual optimum assay conditions. Images can subsequently be recorded either in combination or sequentially through the ability of the HistoFlex to monitor assays without disassembly.

Amplification-free detection of grapevine viruses using an oligonucleotide microarray

A single-colour microarray hybridization system was designed and evaluated for the detection of viruses infecting grapevine. Total RNA (≥0.5μg) from infected plants was converted to cDNA and labelled with Cy3 using two different strategies. While amine-modified and labelled cDNA was adequate for the detection of nepoviruses, the 3DNA technique, a post-hybridization detection method that uses intensely fluorescent dendrimer reagents, was required for the detection of closteroviruses in infected plants. Threshold detection levels were based on the ratio between viral specific and 18S rRNA positive control signal intensities. Oligonucleotides between 27 and 75 nucleotides in length were evaluated and compared. Viruses detected include eight nepoviruses, two vitiviruses, and one each of closterovirus, foveavirus, ampelovirus, maculavirus and sadwavirus. Results of this work demonstrate the potential of microarray technique to detect viral pathogens without sequence bias amplification of template RNA.

A multiplexed immunoassay system based upon reciprocating centrifugal microfluidics

A novel, centrifugal disk-based micro-total analysis system (μTAS) for low cost and high throughput semi-automated immunoassay processing was developed. A key innovation in the disposable immunoassay disk design is in a fluidic structure that enables very efficient micro-mixing based on a reciprocating mechanism in which centrifugal acceleration acting upon a liquid element first generates and stores pneumatic energy that is then released by a reduction of the centrifugal acceleration, resulting in a reversal of direction of flow of the liquid. Through an alternating sequence of high and low centrifugal acceleration, the system reciprocates the flow of liquid within the disk to maximize incubation/hybridization efficiency between antibodies and antigen macromolecules during the incubation/hybridization stage of the assay. The described reciprocating mechanism results in a reduction in processing time and reagent consumption by one order of magnitude.

Microfluidic DNA microarray analysis: a review

Microarray DNA hybridization techniques have been used widely from basic to applied molecular biology research. Generally, in a DNA microarray, different probe DNA molecules are immobilized on a solid support in groups and form an array of microspots. Then, hybridization to the microarray can be performed by applying sample DNA solutions in either the bulk or the microfluidic manner. Because the immobilized probe DNA binds and retains its complementary target DNA, detection is achieved through the read-out of the tagged markers on the sample target molecules. The recent microfluidic hybridization method shows the advantages of less sample usage and reduced incubation time. Here, sample solutions are confined in microfabricated channels and flow through the probe microarray area. The high surface-to-volume ratio in microchannels of nanolitre volume greatly enhanced the sensitivity as obtained with the bulk solution method. To generate nanolitre flows, different techniques have been developed, and this including electrokinetic control, vacuum suction and syringe pumping. The latter two are pressure-driven methods which are more flexible without the need of considering the physicochemical properties of solutions. Recently, centrifugal force is employed to drive liquid movement in microchannels. This method utilizes the body force from the liquid itself and there are no additional solution interface contacts such as from electrodes or syringes and tubing. Centrifugal force driven flow also features the ease of parallel hybridizations. In this review, we will summarize the recent advances in microfluidic microarray hybridization and compare the applications of various flow methods.

Optimization of a microfluidic microarray device for the fast discrimination of fungal pathogenic DNA

A microfluidic microarray device, which has been developed for parallel DNA detection, is now further optimized for more rapid and sensitive DNA detection and for the single-base-pair discrimination of two fungal pathogenic PCR products. Two poly(dimethylsiloxane) (PDMS)-based microfluidic chips consist of radial and spiral microchannels in which flexible probe creation and convenient sample delivery have been achieved by centrifugal pumping. The microarray hybridizations occurred at the cross sections within the spiral channels intersecting the preprinted radial probe lines. The centrifugal pumping method showed advantages over the vacuum suction method in terms of parallel solution delivery and less signal variations between replicate samples. The effect of microchannel depth was studied, and hybridization time is predictable at a certain rotation speed. Cy5 dye labels were proved to show much higher hybridization efficiency as well as less photobleaching effect as compared with the fluorescein dye labels used in our previous work. With these optimized conditions, the method was applied to the detection of three fungal pathogenic polymerase chain reaction (PCR) products with a sample load of 0.2 ng (in 1 microl). Furthermore, the single-base-pair discrimination between the PCR products of two relevant Botrytis species (B. cinerea and B. squamosa) was achieved in a duration as short as 3 min.

Dividable membrane with multi-reaction wells for microarray biochips

This paper presents a multi-well membrane fabricated using polydimethylsiloxane (PDMS) as a part of a microarray biochip that allows dividable incubation chambers to be provided on a single chip. The conditions of the forming temperature, time, and mixing proportion of the materials were investigated to obtain optimal physical absorption with the surface of the chip substrate. To verify the properties of the multi-well chip, immunoassays were performed by the alpha-1-fetoprotein (AFP) antigen sandwich experiment. The results showed that the detection limit reached to the concentration of 10 ng/ml AFP antigen, and that the dynamic range was 30-3000 ng/ml. Attaining excellent physical absorption helps in avoiding cross-contamination or interference between different samples on the same biochip. The merits of dividable multi-well chips include promoting effective use of surface and multiple-sample experiments.

Nano-scale superhydrophobicity: suppression of protein adsorption and promotion of flow-induced detachment

Wall adsorption is a common problem in microfluidic devices, particularly when proteins are used. Here we show how superhydrophobic surfaces can be used to reduce protein adsorption and to promote desorption. Hydrophobic surfaces, both smooth and having high surface roughness of varying length scales (to generate superhydrophobicity), were incubated in protein solution. The samples were then exposed to flow shear in a device designed to simulate a microfluidic environment. Results show that a similar amount of protein adsorbed onto smooth and nanometer-scale rough surfaces, although a greater amount was found to adsorb onto superhydrophobic surfaces with micrometer scale roughness. Exposure to flow shear removed a considerably larger proportion of adsorbed protein from the superhydrophobic surfaces than from the smooth ones, with almost all of the protein being removed from some nanoscale surfaces. This type of surface may therefore be useful in environments, such as microfluidics, where protein sticking is a problem and fluid flow is present. Possible mechanisms that explain the behaviour are discussed, including decreased contact between protein and surface and greater shear stress due to interfacial slip between the superhydrophobic surface and the liquid.

Fungal pathogenic nucleic acid detection achieved with a microfluidic microarray device

Detection of polymerase chain reaction (PCR) products obtained from cultured greenhouse fungal pathogens, Botrytis cinerea and Didymella bryoniae has been achieved using a previously developed microfluidic microarray assembly (MMA) device. The flexible probe construction and rapid DNA detection resulted from the use of centrifugal pumping in the steps of probe introduction and sample delivery, respectively. The line arrays of the oligonucleotide probes were "printed" on a CD-like glass chip using a polydimethylsiloxane (PDMS) polymer plate with radial microfluidic channels, and the sample hybridizations were conducted within the spiral channels on the second plate. The experimental conditions of probe immobilization and sample hybridization were optimized, and both complementary oligonucleotides and PCR products were tested. We were able to achieve adequate fluorescent signals with a sample load as small as 0.5 nM (1 microL) for oligonucleotide samples; for PCR products, we achieved detection at the level of 3 ng.

Analytical investigations on the effects of substrate kinetics on macromolecular transport and hybridization through microfluidic channels

In this paper, a generalized surface-kinetics based model is developed to analytically investigate the influences of the substrate types and the buffer compositions on the macromolecular transport and hybridization in microfluidic channels, under electrokinetic influences. For specific illustration, three typical microchannel substrates, namely silanized glass, polycarbonate and PDMS, are considered, in order to obtain analytical expressions for their zeta potentials as a function of the buffer pH and the substrate compositions. The expressions for the zeta potential are subsequently employed to derive the respective velocity distributions, under the application of electric fields of identical strengths in all cases. It is also taken into consideration that the charged macromolecules introduced into these channels are subjected to electrophoretic influences on account of the applied electric fields. Closed form expressions are derived to predict the transport behaviour of the macromolecules and their subsequent hybridization characteristics. From the analysis presented, it is shown that the modification of the channel surface with silane-treatment becomes useful for enhancing the macromolecular transport and surface hybridization, only if the buffer pH permits a large surface charge density. The analytical solutions are also compared with full-scale numerical solutions of the coupled problem of fluid dynamic and macromolecular transport in presence of the pertinent surface reactions, in order to justify the effectiveness of closed-form expressions derived in this study.

DNA microarrays: design principles for maximizing ergodic, chaotic mixing

In this article we show that models of flows in DNA microarrays generated by pulsed source-sink pairs can be studied as linked twist maps. The significance of this is that it enables us to relate the flow to mathematically precise notions of chaotic mixing that can be realized through specific design criteria. We apply these techniques to three different mixing protocols, two of which have been previously described in the literature, and we are able to isolate the features of each mixer that lead to "good" or "bad" mixing. Based on this, we propose a new design to generate a "well-mixed" flow in a DNA microarray.