Experimental study on the disinfection efficiencies of a continuous-flow ultrasound/ultraviolet baffled reactor

Self-cooling water disinfection reactor with ultraviolet-C light-emitting diodes

The use of ultraviolet-C (UV-C) light-emitting diodes (LEDs) as a water sterilization light source poses a serious challenge in heat dissipation. High junction temperatures reduce the radiant power and lifespan of UV-C LEDs. In this study, a novel self-cooling water disinfection reactor was developed to dissipate Joule heat from UV-C LEDs. The advantage of the self-cooling design is that cooling can be achieved without requiring additional power consumption and cooling liquid. The effects of the water flow rate and driving current of UV-C LEDs on the sterilization of Escherichia coli were investigated for a traditional flow-through reactor and a reactor with self-cooling. The experimental results indicated that an increase in driving current resulted in a considerable increase in the LED temperature of the flow-through reactor but only a marginal increase in the LED temperature of the self-cooling reactor. Under a driving current of 150 mA, the LED temperature of the self-cooling reactor was 55.5°C less than that of the flow-through reactor. The time required by the self-cooling reactor to reach the steady state decreased as the water flow rate increased. Under a flow rate of 100 mL/min, the self-cooling reactor reached the steady state within 62 and 70 s when the driving current was 100 and 150 mA, respectively. Moreover, the average irradiance and inactivation values of the self-cooling reactor were up to 16.5% and 26.0% higher than those of the flow-through reactor, respectively.

Recent trends in the applications of sonochemical reactors as an advanced oxidation process for the remediation of microbial hazards associated with water and wastewater: A critical review

Water is one of the major sources that spread human diseases through contamination with bacteria and other pathogenic microorganisms. This review focuses on microbial hazards as they are often present in water and wastewater and cause various human diseases. Among the currently used disinfection methods, sonochemical reactors (SCRs) that produce free radicals combined with advanced oxidation processes (AOPs) have received significant attention from the scientific community. Also, this review discussed various types of cavitation reactors, such as acoustic cavitation reactors (ACRs) utilizing ultrasonic energy (UE), which had been widely employed, involving AOPs for treating contaminated waters. Besides ACRs, hydrodynamic cavitation reactors (HCRs) also effectively destroy and deactivate microorganisms to varying degrees. Cavitation is the fundamental phenomenon responsible for initiating many sonochemical reactions in liquids. Bacterial degradation occurs mainly due to the thinning of microbial membranes, local warming, and the generation of free radicals due to cavitation. Over the years, although extensive investigations have focused on the antimicrobial effects of UE (ultrasonic energy), the primary mechanism underlying the cavitation effects in the disinfection process, inactivation of microbes, and chemical reactions involved are still poorly understood. Therefore, studies under different conditions often lead to inconsistent results. This review investigates and compares other mechanisms and performances from greener and environmentally friendly sonochemical techniques to the remediation of microbial hazards associated with water and wastewater. Finally, the energy aspects, challenges, and recommendations for future perspectives have been provided.

Sanitary sewage disinfection with ultraviolet radiation and ultrasound

Currently, the world is facing a horrible situation due to SARS-CoV-2. Though its RNA was found in wastewater, there are still no studies on RNA contamination detected in sewage. Hence, a possible treatment of sewage is suggested in this work. The disinfection stage is extremely important in the treatment of effluents, minimizing the impacts on the receiving body of water and promoting public health. In this context, the sequential use of ultrasound and ultraviolet radiation, on a bench scale, was investigated as a way to improve the disinfection of anaerobically treated effluents. Two types of treated effluents were tested, by septic tank and anaerobic filter, for which, two ultrasound frequencies, 25 and 40 kHz, and four doses of UV, 3.6; 9.0; 18 and 36 mJ cm^-2 were applied. Physicochemical and microbiological parameters were observed for individual and sequential assays. The better quality of the anaerobic filter effluent influenced the performance of both processes, decreasing the concentration of organic load and turbidity, even though a concentration of total coliforms and Escherichia coli occurred in the lowest quality effluent (septic tank). The application of ultrasound has a positive effect on the inactivation of total coliforms and E. coli up to 1.0 log and provides better conditions for ultraviolet radiation to be sequentially applied. The UV radiation applied for the septic tank and the anaerobic filter inactivates 2.5 log for total coliforms and 3.5 log for E. coli, respectively. It is suggested that the disinfection methods applied in this work to inactivate gram-negative bacteria (E. coli) can also be applied to secondary treatment effluents, as well as being better tested for viruses, protozoa, and helminths.

SUPPLEMENTARY INFORMATION

The online version contains supplementary material available at 10.1007/s13762-021-03764-7.

Removal of tetracycline-resistant Escherichia coli and its genes through ultrasound treatment combined with ultraviolet light emitting diodes

Antibiotic resistance has gained increasing attention worldwide, and wastewater treatment plants have been regarded as hotspots for antibiotic-resistant bacteria and antibiotic-resistant genes (ARGs). In this study, we evaluated the removal of tetracycline-resistant Escherichia coli and its related genes through ultrasound (US) treatment with different input levels of US-specific energy combined with ultraviolet light emitting diodes (UV-LEDs). Simultaneous US with UV-LEDs effectively eliminated tetracycline-resistant E. coli with the normal suggested UV-LEDs dosage (below 30 mJ/cm²). The removal efficiency increased with the addition of US (specific input energy of 8-16 kJ/L), and simultaneous US treatment with UV-LEDs was relatively more effective than US pretreatment. Analyses of cell damage by K⁺ leakage and flow cytometry showed that the cell wall kept its integrity during the applied treatment conditions. Consequently, the removal efficiencies of 16 S rRNA, tet M, and tet Q were unsatisfactory because less than 1 log reduction was achieved. Increasing the US energy remarkably damaged the cell wall and potentially promoted the reaction. The removal of ARGs increased four times when using US-specific input energy at 330 kJ/L with 5 mJ/cm² compared with UV-LEDs alone. The US treatment combined with UV-LEDs is a novel process that does not require chemicals. Results of this research can provide theoretical support for the removal of ARGs.

Disinfection of Wastewater by UV-Based Treatment for Reuse in a Circular Economy Perspective. Where Are We at?

Among the critical issues that prevent the reuse of wastewater treatment plants (WWTPs) effluents in a circular economy perspective, the microbiological component plays a key role causing infections and diseases. To date, the use of conventional chemical oxidants (e.g., chlorine) represent the main applied process for wastewater (WW) disinfection following a series of operational advantages. However, toxicity linked to the production of highly dangerous disinfection by-products (DBPs) has been widely demonstrated. Therefore, in recent years, there is an increasing attention to implement sustainable processes, which can simultaneously guarantee the microbiological quality of the WWs treated and the protection of both humans and the environment. This review focuses on treatments based on ultraviolet radiation (UV) alone or in combination with other processes (sonophotolysis, photocatalysis and photoelectrocatalysis with both natural and artificial light) without the dosage of chemical oxidants. The strengths of these technologies and the most significant critical issues are reported. To date, the use of synthetic waters in laboratory tests despite real waters, the capital and operative costs and the limited, or absent, experience of full-scale plant management (especially for UV-based combined processes) represent the main limits to their application on a larger scale. Although further in-depth studies are required to ensure full applicability of UV-based combined processes in WWTPs for reuse of their purified effluents, excellent prospects are presented thanks to an absent environmental impact in terms of DBPs formation and excellent disinfection yields of microorganisms (in most cases higher than 3-log reduction).

Microbiological Reduction Strategies of Irrigation Water for Fresh Produce

ABSTRACT

Irrigation water can be a source of pathogenic contamination of fresh produce. Controlling the quality of the water used during primary production is important to ensure food safety and protect human health. Several measures to control the microbiological quality of irrigation water are available for growers, including preventative and mitigation strategies. However, clear guidance for growers on which strategies could be used to reduce microbiological contamination is needed. This study evaluates pathogenic microorganisms of concern in fresh produce and water, the microbiological criteria of water intended for agricultural purposes, and the preventative and mitigative microbial reduction strategies. This article provides suggestions for control measures that growers can take during primary production to reduce foodborne pathogenic contamination coming from irrigation water. Results show that controlling the water source, regime, and timing of irrigation may help to reduce the potential exposure of fresh produce to contamination. Moreover, mitigation strategies like electrolysis, ozone, UV, and photocatalysts hold promise either as a single treatment, with pretreatments that remove suspended material, or as combined treatments with another chemical or physical treatment(s). Based on the literature data, a decision tree was developed for growers, which describes preventative and mitigation strategies for irrigation-water disinfection based on the fecal coliform load of the irrigation water and the water turbidity. It helps guide growers when trying to evaluate possible control measures given the quality of the irrigation water available. Overall, the strategies available to control irrigation water used for fresh produce should be evaluated on a case-by-case basis because one strategy or technology does not apply to all scenarios.

HIGHLIGHTS

Review on low- and high-frequency sonolytic, sonophotolytic and sonophotochemical processes for inactivating pathogenic microorganisms in aqueous media

Ultraviolet and ultrasound-based advanced oxidation processes (AOPs) are gaining considerable research attention for water treatment and disinfection. Compared to low-frequency ultrasound (LFUS, <100 kHz), high-frequency ultrasound (HFUS, >100 kHz and MHz range) for water disinfection remains much less investigated. The present review aims at surveying and discussing literature data on microbial inactivation in non-food aqueous media using HFUS alone and with AOPs. More specifically, the review covers sonophotolytic (US/UV) processes under sequential and simultaneous modes as well as sonophotochemical processes, where both low and high frequencies were applied. Addressing a state-of-the-art biomedical research, we have attempted to provide more insight into mechanical and sonochemical mechanisms of inactivation under ultrasonic exposure. Sonoporation, intracellular generation of reactive oxygen species (ROS), energy stimulation of aquaporins to deliver ROS, and injection of extracellular ROS into sonoporated cells have all been identified as primary ways of inactivation. Application of ultrasound in the 0.2-2 MHz range and mercury-free light sources to support the Minamata Convention on Mercury is an ongoing challenge for effective elimination of microbial pathogens from water and wastewater through sonophotolytic and sonophotochemical AOPs.

Assessment of a low-frequency ultrasound device on prevention of biofilm formation and carbonate deposition in drinking water systems

A device generating low-frequency and low-intensity ultrasound waves was used for mitigating biofilm accumulation and scaling. Two systems were tested: a lab-scale plate heat exchanger operated with continuously recycled water and a continually fed flow-through drinking water pilot used for mimicking water circulation in pipes. Initial deposition of bacterial cells was not prevented by ultrasound wave treatment. However, whatever the tested system, both further calcium carbonate deposition and biofilm growth were markedly inhibited. Biofilms formed in reactors subjected to low-frequency and low-intensity ultrasound waves were weakly attached to the material. Even though the activity of bacteria was affected as shown by their lower cultivability, membrane permeability did not appear compromised. Ultrasound technology sounds very promising in both the mitigation of drinking water biofilm and carbonate accumulation.

Rapid and high-capacity ultrasonic assisted adsorption of ternary toxic anionic dyes onto MOF-5-activated carbon: Artificial neural networks, partial least squares, desirability function and isotherm and kinetic study

The present paper focused on the ultrasonic assisted simultaneous removal of fast green (FG), eosin Y (EY) and quinine yellow (QY) from aqueous media following using MOF-5 as a metal organic framework and activated carbon hybrid (AC-MOF-5). The structure and morphology of AC-MOF-5 was identified by SEM, FTIR and XRD analysis. The interactive and main effects of variables such as pH, initial dyes concentration (mgL^-1), adsorbent dosage (mg) and sonication time (min) on removal percentage were studied by central composite design (CCD), subsequent desirability function (DF) permit to achieved real variable experimental condition. Optimized values were found 7.06, 5.68, 7.59 and 5.04mgL^-1, 0.02g and 2.55min for pH, FG, EY and QY concentration, adsorbent dosage and sonication time, respectively. Under this conditions removal percentage were obtained 98.1%, 98.1% and 91.91% for FG, EY and QY, respectively. Two models, namely partial least squares (PLS) and multi-layer artificial neural network (ANN) model were used for building up to construct an empirical model to predict the dyes under study removal behavior. The obtained results show that ANN and PLS model is a powerful tool for prediction of under-study dyes adsorption by AC-MOF-5. The evaluation and estimation of equilibrium data from traditional isotherm models display that the Langmuir model indicated the best fit to the equilibrium data with maximum adsorption capacity of 21.230, 20.242 and 18.621mgg^-1, for FG, EY and QY, respectively, while the adsorption rate efficiently follows the pseudo-second-order model.

Disinfection effect of a continuous-flow ultrasound/ultraviolet baffled reactor at a pilot scale

An ultrasound/ultraviolet (US/UV) baffled reactor was developed to fill the gap in ultraviolet (UV) disinfection associated with disinfection efficiency. According to the previously selected operational condition, a continuous-flow US/UV baffled reactor was continuously operated in a wastewater treatment plant at a pilot scale for nearly three months, and the disinfection influent and effluent were analyzed, including fecal coliforms, Escherichia coli, and fecal streptococci. The US/UV baffled reactor could guarantee a high effluent disinfection performance in terms of fecal coliforms removal even with the fluctuation of the secondary effluent. All the disinfected effluents satisfied the requirement of the "Pollutants Discharge Standard of Municipal Wastewater Treatment Plant in China" (fecal coliforms below 1000CFU/L for class 1A), and 87% of the tested fecal coliforms concentration in the disinfected effluent was below 100CFU/L, nearly eliminating all fecal coliforms. Further analysis of the E. coli and fecal streptococci showed the broad disinfection ability and high disinfection efficiency of the US/UV baffled reactor. The flexibility of the specific energy consumption for the disinfection system depends on the water quality.

Intensification of abamectin pesticide degradation using the combination of ultrasonic cavitation and visible-light driven photocatalytic process: Synergistic effect and optimization study

Degradation of abamectin pesticide was carried out using visible light driven Cu₂(OH)PO₄-HKUST-1 MOF photocatalyst through the sonophotocatalytic technique. Cu₂(OH)PO₄-HKUST-1 MOF as a visible-light driven photocatalyst, was synthesized and characterized by XRD, SEM, EDS and DRS. The direct bang gaps of HKUST-1 MOF and Cu₂(OH)PO₄-HKUST-1 MOF were estimated about 2.63 and 2.59eV, respectively, which reveals that these photocatalysts can be activated under blue light illumination. All sonophotodegradation experiments were performed using a continuous flow-loop reactor. The central composite design (CCD) methodology was applied for modeling, optimization and investigation of influence of operational parameters, i.e. irradiation time, pH, solution flow rate, oxygen flow rate, initial concentration and photocatalyst dosage on the sonophotocatalytic degradation of abamectin. The maximum degradation efficiency of 99.93% was found at optimal values as 20min, 4, 90mL/min, 0.2mL/min, 30mg/L and 0.4g/L, for irradiation time, pH, solution flow rate, oxygen flow rate, initial concentration and photocatalyst dosage, respectively. Evaluation of the synergism in the combination of ultrasonic and photocatalysis lead to a synergistic index of 2.19, which reveals that coupling of ultrasonic and photocatalysis has a greater efficiency than the sum of individual procedures for degradation of abamectin.

Kinetics of inactivation and photoreactivation of Escherichia coli using ultrasound-enhanced UV-C light-emitting diodes disinfection

Ultraviolet (UV) disinfection is highly recommended owing to its high disinfection efficiency and disinfection by-products free, and UV Light-Emitting Diodes (UV LEDs) is increasingly becoming an alternative of mercury UV lamps for water disinfection owing to its long lifetime, low input power, and absence of problems on disposal. However, renovation of existing UV lamps faces the challenges for UV disinfection associated with disinfection efficiency and photoreactivation, and modified UV disinfection process is required for practical application. In this study, mathematical rule of disinfection and photoreactivation in a US enhanced UV disinfection system was investigated. UV LED with peak emission at 254nm (UV-C LED) was selected as representative for UV lamps, and a low frequency US was used as pretreatment followed by UV disinfection. The disinfection efficiency of Escherichia coli in deionized water (DI), DI water with kaoline suspension (DIK), and secondary effluent (SE) of municipal wastewater treatment plant were analyzed. Moreover, photoreactivation of E. coli in DIK water within 6h after disinfection was conducted. The experimental results showed that the disinfection efficiencies had good fit with Chick-Watson first-order linear model, and US pretreatment increased the inactivation rate constant for E. coli, which increased from 0.1605 to 0.1887 in the DIK water. Therefore, US pretreatment with UV disinfection have potential to shorten the retention time and reduce the reactor volume. Moreover, the number of photoreactivated E. coli in effluent was reduced under UV-C LED disinfection with US pretreatment compared with that under UV-C LED disinfection alone. The order of maximum percentage of photo-reactivated E. coli was as follows: UV-C LED disinfection alone at 30mJ/cm²>UV-C LED disinfection at 25mJ/cm² with US pretreatment>UV-C LED disinfection at 30mJ/cm² with US pretreatment. The survival ratio versus photoreactivation time showed a good fit to second-order logistic model. US pretreatment in UV-C LED disinfection could improve disinfection efficiency, reducing photoreactivation in the effluent as well, which offers a promising practical application technology.

Sonophotocatalytic degradation of trypan blue and vesuvine dyes in the presence of blue light active photocatalyst of Ag3PO4/Bi2S3-HKUST-1-MOF: Central composite optimization and synergistic effect study

An efficient simultaneous sonophotocatalytic degradation of trypan blue (TB) and vesuvine (VS) using Ag3PO4/Bi2S3-HKUST-1-MOF as a novel visible light active photocatalyst was carried out successfully in a continuous flow-loop reactor equipped to blue LED light. Ag3PO4/Bi2S3-HKUST-1-MOF with activation ability under blue light illumination was synthesized and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), photoluminescence (PL) and diffuse reflectance spectra (DRS). The effect of operational parameters such as the initial TB and VS concentration (5-45mg/L), flow rate (30-110mL/min), irradiation and sonication time (10-30min), pH (3-11) and photocatalyst dosage (0.15-0.35g/L) has been investigated and optimized using central composite design (CCD) combined with desirability function (DF). Maximum sonophotodegradation percentage (98.44% and 99.36% for TB and VS, respectively) was found at optimum condition set as: 25mg/L of each dye, 70mL/min of solution flow rate, 25min of irradiation and sonication time, pH 6 and 0.25g/L of photocatalyst dosage. At optimum conditions, synergistic index value was obtained 2.53 that indicated the hybrid systems including ultrasound irradiation and photocatalysis have higher efficiency compared with sum of the individual processes.

Influence of ultrasound enhancement on chlorine dioxide consumption and disinfection by-products formation for secondary effluents disinfection

Chlorine dioxide (ClO2) has been promoted as an alternative disinfectant because of its high disinfection efficiency and less formation of organic disinfection by-products (DBPs). However, particle-associated microorganisms could be protected during the disinfection process, which decreases the disinfection efficiency or increases the required dosage. Besides, the formation of inorganic disinfection by-products is a significant concern in environment health. Ultrasound (US)-combined disinfection methods are becoming increasingly attractive because they are efficient and environmentally friendly. In this study, US was introduced as an enhancement method to identify its influence on ClO2 demand reduction and to minimize the production of potential DBPs for secondary effluents disinfection. Fecal coliform was used as an indicator, and DBPs, including trichloromethane (TCM), dichloroacetic acid (DCAA), trichloroacetic acid (TCAA), chlorite (ClO2(-)), and chlorate (ClO3(-)), were analyzed to observe the potential DBPs formation. Results show that US pretreatment could reduce half of ClO2 dosage compared with ClO2 disinfection alone for the same disinfection efficiency, and that an input power density of 2.64 kJ/L pretreatment with the 1.5mg/L ClO2 was enough to meet the discharge requirement in China (i.e., fecal coliform below 1000 CFU/L for Class 1A) for secondary effluent disinfection, and the ClO2(-) concentration in the disinfection effluent was only 1.37 mg/L at the same time. Furthermore, the different effects of US on the two processes (US as pretreatment and simultaneous US/ClO2 disinfection) were also analyzed, including deagglomerating, cell damage, and synergistic disinfection as well as degasing/sonolysis. It was proved that the production of TCM, DCAA, and TCAA was insignificantly influenced with the introduction of US, but US pretreatment did reduce the production of ClO2(-) and ClO3(-) effectually. In general, US pretreatment could be a better option for disinfection enhancement methods combined with ClO2 in terms of both disinfection efficiency and disinfection by-product formation.