Apatite accumulation enhances the mechanical property of anammox granules

Insight into anammox granular system operation in wet/dry weather

Effects of short hydraulic retention time (HRT) in wet weather and long HRT in dry weather on sludge properties, microbial community, and metabolomic of anammox granular system were studied. Results showed under equal nitrogen loading rate (0.4 kg N/(m3 · d)) conditions, an HRT of 4.41 h was beneficial for total nitrogen removal efficiency (78.9 %). The shorter the HRT, the lower the particle density (1.01±0.34 g/cm3), the lower the settling performance (1.18±0.28 cm/s), and the worse the biomass retention (1.04±0.18 g/L), but the higher the mechanical strength (85.22 Pa). Properly decreasing HRT could increase the permeability of anammox granules, ensuring their activity. Metabolomics analysis indicated that the activity of anaerobic ammonium oxidizing bacteria was promoted by stimulating the metabolic pathways of amino acids and glycerophospholipids. In summary, this research clarified the effect of wet/dry weather on anammox granular system and provided theoretical guidance for the application in engineering.

Simultaneous nitrogen and phosphorus removal through an integrated partial-denitrification/anammox process in a single UAFB system

With the aim of obtaining enhanced nitrogen removal and phosphate recovery in mainstream sewage, we examined an integrated partial-denitrification/anaerobic ammonia oxidation (PD/A) process over a period of 189 days to accomplish this goal. An up-flow anaerobic fixed-bed reactor (UAFB) used in the integrated PD/A process was started up with anammox sludge inoculated and the influent composition controlled. Results showed that the system achieved a phosphorus removal efficiency of 82% when the influent concentration reached 12.0 mg/L. Batch tests demonstrated that stable and efficient removal of chemical oxygen demand (COD), nitrogen, and phosphorus was achieved at a COD/NO3--N ratio of 3.5. Scanning electron microscope (SEM) and X-ray diffraction (XRD) analysis indicated that hydroxyapatite was the main crystal in the biofilm. Furthermore, substrate variation along the axial length of UAFB indicated that partial denitrification and anammox primarily took place near the reactor's bottom. According to a microbiological examination, 0.4% of the PD/A process's microorganisms were anaerobic ammonia oxidizing bacteria (AnAOB). Ca. Brocadia, Ca. Kuenenia, and Ca. Jettenia served as the principal AnAOB generals in the system. Thauera, Candidatus Accumulibacter, Pseudomonas, and Acinetobacter, which together accounted for 27% of the denitrifying and phosphorus-accumulating bacteria, were helpful in advanced nutrient removal. Therefore, the combined PD/A process can be a different option in the future for sewage treatment to achieve contemporaneous nutrient removal.

Granulation of partial denitrification sludge: Advances in mechanism understanding, technologies development and perspectives

The high-rate and stably efficient nitrite generation is vital and still challenges the wide application of partial denitrification (PD) and anammox technology. Increasing attention has been drawn to the granulation of PD biomass. However, the knowledge of PD granular sludge is still limited in terms of granules characterization and mechanisms of biomass aggregation for high nitrite accumulation. This work reviewed the performance and granulation of PD biomass for high nitrite accumulation via nitrate reduction, including the system start-up, influential factors, granular characteristics, hypothetical mechanism, challenges and perspectives in future application. The physiochemical characterization and key influential factors were summarized in view of nitrite production, morphology analysis, extracellular polymer substance structure, as well as microbial mechanisms. The PD granules exhibit potential advantages of a high biomass density, good settleability, high hydraulic loading rates, and strong shock resistance. A novel granular sludge-based PD combined with anammox process was proposed to enhance the capability of nitrogen removal. In the future, PD granules utilizing different electron donors is a promising way to broaden the application of anammox technology in both municipal and industrial wastewater treatment.

Enhancing start-up strategies for anammox granular sludge systems: A review

The anaerobic ammonium oxidation (anammox) process has been developed as one of the optimal alternatives to the conventional biological nitrogen removal process because of its high nitrogen removal capacity and low energy consumption. However, the slow growth rate of anammox bacteria and its high sensitivity to environmental changes have resulted in fewer anammox sludge sources for process start-up and a lengthy start-up period. Given that anammox microorganisms tend to aggregate, granular-anammox sludge is a frequent byproduct of the anammox process. In this study, we review state-of-the-art strategies for promoting the formation of anammox granules and the start-up of the anammox process based on the literature of the past decade. These strategies are categorized as the transformation of alternative sludge, the addition of accelerators, the introduction of functional carriers, and the implementation of other physical methods. In addition, the formation mechanism of anammox granules, the operational performance of various strategies, and their promotion mechanisms are introduced. Finally, prospects are presented to indicate the gaps in contemporary research and the potential future research directions. This review functions as a summary guideline and theoretical reference for the cultivation of granular-anammox sludge, the start-up of the anammox process, and its practical application.

Anammox-Mediated Hydroxyapatite Granules: Physicochemical Properties, 3D Hierarchy, and Biofilm Thickness

Biomineralization inspired the development of simultaneous biological transformations and chemical precipitation for simultaneous nitrogen removal and phosphorus recovery from wastewater, which could compensate for the incapacity of phosphorus management in the new biological route of anaerobic ammonium oxidation (anammox). In this study, we strengthened anammox-mediated biomineralization by long-term feeding of concentrated N, P, and Ca substrates, and a self-assembled matrix of anammox bacteria and hydroxyapatite (HAP) was fabricated in a granular shape, defined as HAP-anammox granules. HAP was identified as the dominant mineral using elemental analysis, X-ray diffraction, and Raman spectroscopy. The intensive precipitation of HAP resulted in a higher inorganic fraction and substantially improved settleability of anammox biomass, which facilitated HAP precipitation by acting as nucleation and metabolically elevated pH. By using X-ray microcomputed tomography, we visually represented the hybrid texture of interwoven HAP pellets and biomass, the core-shell layered architecture of different-sized HAP-anammox granules, and their homogeneously regulated thickness of the outer biofilm (from 118 to 635 μm). This unique architecture endows HAP-anammox granules with outstanding settleability, active biofilm, and tightly bonded biofilm with the carrier, which may explain the excellent performance of these HAP-anammox granules under various challenging operational conditions in previous studies.

Energy-neutral municipal wastewater treatment based on partial denitrification-anammox driven by side-stream sulphide

"Low-carbon" has become an important evaluation index of modernisation construction. In the area of wastewater treatment has also caused considerable concern. Anaerobic ammonium oxidation (anammox) is a novel autotrophic nitrogen removal process that provides an opportunity for low-carbon remodelling of municipal wastewater treatment plants (MWTPs). The stable supply of nitrite is of great significance for the application of anammox. As a process with stable nitrite supply, partial denitrification (PD) is of great significance in the coupling nitrogen removal with anammox in municipal wastewater. Furthermore, innovation of the low-carbon nitrogen removal process can enable the recovery of abundant bioenergy resource from MWTPs. The low-carbon nitrogen removal via PD-anammox process and the bioenergy recovery for municipal wastewater in the previous studies has been summarised. On this basis, a novel energy-neutralisation municipal wastewater treatment process based on partial denitrification-anammox driven by sulphide produced in the side-stream has been proposed. The long-term retention of mainstream anammox and improvement of energy recovery efficiency under the requirement of ensuring nitrogen removal require additional detailed investigation.

Anammox upflow hybrid reactor: Nitrogen removal performance and potential for phosphorus recovery

Echoing to the call of recovering high-value-added chemicals from wastewater and achieving carbon-neutral operation in wastewater treatment, an anammox upflow hybrid reactor was successfully applied for nitrogen removal, and the potential for phosphorus recovery was put forward. Moreover, the spatial pattern of removal capacities, and distribution of biomass and HAP precipitates were recognized and demonstrated as height-oriented. The intensity of HAP precipitates was highly consistent with the amount of anammox biomass and the relative abundance of the Candidatus Kuenenia, indicating that HAP formation was encouraged by the anammox reaction itself and heterogeneous nucleation induced by organic matters (proteins and polysaccharides). The fixed bed also played an important role in immobilizing the anammox biomass, secreted organic matrix, and HAP precipitates. This finding also provoked the thought that in the anammox process, HAP precipitation was more achievable, effective and practicable using the fixed-carrier system.

Improving mechanical stability of anammox granules with organic stress by limited filamentous bulking

Under organic stress, the limited filamentous bulking (FB) was demonstrated to improve anammox capability by inhibiting granule disintegration and washout. The accumulation of internal stress played a more important role than the adverse physicochemical properties (low viscoelasticity and hydrophobicity) of granules in limiting granular strength by consuming the granular elastic energy. Different from the floc-forming heterotrophic bacteria (HB) that stored its growth stress as internal stress by pushing the surrounded anammox micro-colonies outwards under the spatial constraint of elastic anammox "shell", the filamentous HB grew into a uniform network structure within granules, endowed granules low internal stress and acted as the granular skeleton due to its rich amyloid substance, which was benefited from the elimination of inhomogeneous growth and the consequent expansion competition for living space. Combined with the mechanical instability and sticking-spring models, controlling FB at limited level was effective for improving granular strength without affecting sludge-water separation.

A new pattern of the partial nitrification and Anammox immobilized gel beads: core-shell embedded carrier

Single-stage partial nitrification and Anammox (PN/A) is an efficient and energy-saving denitrification process for wastewater. However, its application is limited by the growth conditions of microorganisms. Therefore, we improved the PN/A by developing a novel core-shell embedded carrier. With Anammox gel as the core and Ammonia-oxidizing bacteria gel as the shell, these beads can achieve dissolved oxygen partitioning and provide a suitable environment for the growth of different bacteria. On this basis, the influence of the shape of core-shell embedded gel on nitrogen removal performance was systematically studied, and the internal morphology and pore size of gel beads were characterized. The results showed that the nitrogen removal efficiency of spherical and square gels was increased by 33.70% and 13.47%, respectively, in the batch test. Fluorescence in situ hybridization confirmed the stratified growth of ammonia-oxidizing bacteria and Anammox in carriers, and the relative abundance value of the two bacteria were 1.25:1 and 1.43:1, respectively. Although the mechanical strength of square gel beads is slightly higher than that of spherical, spherical gel is considered the most suitable gel shape due to its small pore size and poor pore connectivity, which ensures the matching of internal Anammox and external PN reaction. In the long-term experiment, the core-shell embedded beads still had the design characteristics, and the TN removal efficiency was increased by 36.25% despite occasional oxygen excess.

Unveiling significance of Ca2+ ion for start-up of aerobic granular sludge reactor by distinguishing its effects on physicochemical property and bioactivity of sludge

Almost all of the aerobic granular sludge (AGS) reactors were fed on certain amounts of Ca²⁺ ion, but whether and why it was necessary for reactor start-up remain unknown. Herein, this study conducted a set of comparative experiments in three AGS reactors, which were operated in parallel with Ca²⁺ addition in R3, hydroxyapatite (HAP) addition in R1, and without any forms of Ca addition in R2. Results showed that R3 not only achieved the complete granulation of sludge, but exhibited superior performance of COD and nutrient removal. In contrast, R1 had a slightly quicker granulation rate than R3 (R1: 0.07 day^-1; R3: 0.06 day^-1), but the formed granules could not efficiently degrade pollutants. In R2, both sludge granulation and pollutants removal did not proceed normally. Further investigations found that the Ca²⁺ ion acted in three ways: (1) it increased inorganic composition of sludge to promote granulation; (2) the transformed HAP strengthened stability of granular structure; (3) it ensured bioactivity of granules by driving enrichment of functional microbes and synthesis of metabolism enzymes. Overall, this study systemically proved significance of Ca²⁺ ion for the start-up of AGS reactors and its influencing mechanisms on different properties of granules.

Heavy metal biosorption by Extracellular Polymeric Substances (EPS) recovered from anammox granular sludge

The recovery and conversion of Extracellular Polymeric Substances (EPS) from sewage sludge into bio-based commodities might improve the economics and environmental sustainability of wastewater treatment. This contribution explores the application of EPS from anammox granular waste sludge as biosorbent for the removal of heavy metals, specifically lead, copper, nickel, and zinc. Adsorption capacities equivalent or higher than well-established adsorbent media emerged from single-metal biosorption studies (up to 84.9, 52.8, 21.7 and 7.4 mg/gTS_EPS for Pb²⁺, Cu²⁺, Ni²⁺ and Zn²⁺, respectively). Combining spectroscopic techniques, a mechanistic hypothesis for metal biosorption, based on a combination of electrostatic interaction, ion exchange, complexation, and precipitation, was proposed. The adsorption mechanisms of extracted EPS and non-extracted EPS in the native biomass were indirectly compared by means of single-metal biosorption studies performed with pristine granules (adsorbing up to 103.7, 36.1, 48.2 and 49.8 mg/gTSgranules of Pb²⁺, Cu²⁺, Ni²⁺, and Zn²⁺, respectively). In comparison with pristine anammox granules, EPS showed lower adsorption capacities except for copper and different adsorption pathways as postulated based on the adsorption data interpretation via theoretical models. The multi-metal biosorption tests excluded significant competitions among different heavy metals for the EPS binding sites, thus opening further scenarios for the treatment of complex wastewaters.

Granular activated carbon promoting re-granulation of anammox-hydroxyapatite granules for stable nitrogen removal at low phosphate concentration

Anaerobic ammonium oxidation (anammox) coupled with hydroxyapatite (HAP) crystallization not only achieves simultaneous nitrogen removal and phosphorus recovery, but also cultivates excellent anammox granules. However, a floatation and wash-out of anammox-HAP granules was occurred at low phosphate concentrations. In this study, a reactor inoculated with mature anammox-HAP granules and fed with low phosphate (5 mg P/L) was added with granular activated carbon (GAC) to maintain sludge granulation and nitrogen-removing stability. At influent total nitrogen >800 mg/L and nitrogen loading rate ~ 9.8 kg/m³/d, a satisfactory nitrogen removal of around 88% was maintained during 140 days of operation. Insufficient phosphate supplement resulted in a sludge bulking, with suspended solid and sludge density decreased whereas sludge water content and expansion ratio increased due to HAP loss. Nevertheless, the sludge re-granulation was found at the later stage as the proportion of granules in 2.8- 3.35 mm went up to 37.4% after large granules disintegrated into small pieces at the initial stage. The settling velocity was finally ranging from 129.8 to 182.2 m/h. In addition, Candidatus Brocadia was increased from 2.1% to 20.1% and dominated in the microbial community. These findings suggest GAC was able to promote re-granulation of anammox-HAP granules at low phosphate concentration, which avoids sludge flotation and widens their application as an inoculum.

Exploration of mechanisms for calcium phosphate precipitation and accumulation in nitrifying granules by investigating the size effects of granules

Calcium phosphate could be accumulated in aerobic granules, which attracts attention recently for phosphorus removal and recovery from wastewater. In this study, partial nitrifying granules with high calcium precipitate content were sorted into different size groups for characterization and evaluation to reveal the dynamic balance of granules at stead state and relevant calcium phosphate precipitation and accumulation mechanism. It was found that light yellow small granules without calcium precipitates but high microbial activity co-existed with deep brown granules with calcium precipitate of around 91% and low microbial activity. Characterization with specific oxygen uptake rates, specific ammonium oxidation rates, calcium and phosphate removal rates from solution, EPS contents, elemental compositions by energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), and scanning electron microscopy (SEM) for different size groups of granules enabled a proposal of a new hypothesized mechanism for calcium precipitation and accumulation. With this proposed mechanism, it is believed that sufficient granule retention time in reactors was critical for the accumulation of calcium precipitates followed by a slow microbial growth rate of biomass due to mass transfer resistance. The co-precipitation of calcium carbonate and calcium phosphate mainly occurred in granules with a size less than 710 µm while calcium phosphate dominant minerals were accumulated in granules larger than 710 µm. The results and conclusions in this study shed light on the mechanisms of calcium phosphate accumulation in granules, which could be used to better operate and control aerobic granular sludge with calcium phosphates for phosphorus removal and recovery.

Architecture of HAP-anammox granules contributed to high capacity and robustness of nitrogen removal under 7°C

The anaerobic ammonium oxidation (anammox) process is an autotrophic nitrogen removal process with great potential as a cost-effective and highly efficient technology in the wastewater treatment field. The main challenges yet to be overcome in this new frontier technology are operating at lower temperatures and achieving a high and stable nitrogen removal efficiency. In this study, an up-flow expanded bed reactor with hydroxyapatite (HAP)-anammox granules was operated for more than 200 days at 7°C. The nitrogen loading rate (NLR) was improved from 1.0 g-N/L/d to 3.6 g-N/L/d, together with a high-level nitrogen removal efficiency of 84-92%, which is the highest to date at extremely low temperatures in a continuous experiment. Candidatus Kuenenia was revealed to be the only dominant anammox genus, with a relative abundance of 35.3-37.5%. The optimal operational temperature was around 35°C and the apparent activation energy (E_a) was calculated as 78.37 kJ/mol. The three-layers architecture and architectural evolution of HAP-anammox granules into HAP-cores and peeling biofilms with outstanding settling performance were characterized. Under 7°C, the high capacity of nitrogen removal with robust removal efficiency using HAP-anammox granules was achieved.

Hydroxyapatite Precipitation and Accumulation in Granules and Its Effects on Activity and Stability of Partial Nitrifying Granules at Moderate and High Temperatures

Precipitation and accumulation of calcium phosphate in granular sludge has attracted research attention recently for phosphate removal and recovery from wastewater. This study investigated calcium phosphate accumulation from granulation stage to steady state by forming heterotrophic granules at different COD/N ratios at 21 and 32 °C, respectively, followed by the transformation of heterotrophic granules to partial nitrifying granules. It was found that mature granules accumulated around 60–80% minerals in granules, much higher than young granules with only around 30% ash contents. In addition, high temperature promoted co-precipitation of hydroxyapatite and calcite in granules with more calcite than hydroxyapatite and only 4.1% P content, while mainly hydroxyapatite was accumulated at the moderate temperature with 7.7% P content. The accumulation of minerals in granules at the high temperature with 75–80% ash content also led to the disintegration and instability of granules. Specific ammonium oxidation rates were reduced, as well, from day 58 to day 121 at both temperatures due to increased mineral contents. These results are meaningful to control or manipulate granular sludge for phosphorus removal and recovery by forming and accumulating hydroxyapatite in granules, as well as for the maintenance of microbial activities of granules.

Achieving superior nitrogen removal performance in low-strength ammonium wastewater treatment by cultivating concentrated, highly dispersive, and easily settleable granule sludge in a one-stage partial nitritation/anammox-HAP reactor

In low-strength ammonium wastewater (LSAWW) treatment, the application of anammox-based process is still limited due to extreme instability and the poor nitrogen removal rate (NRR). In this work, granule sludge, comprised of functional microbes and hydroxyapatite (HAP), was inoculated and cultivated in a one-stage partial nitritation/anammox (PNA) reactor for LSAWW treatment. The results showed that at the hydraulic retention time (HRT) of about 1.0 h and the influent ammonium concentration of 63.0 mg/L, an average NRR of 1.28 kg/m³/d was achieved, which far exceeds that reported in similar studies. The main inorganic matter in sludge was identified as HAP through the X-ray diffractometer and Raman spectrum analysis. The tomographic images of wet granule created through computed tomography revealed that the interior density of the granules was uneven and many hollow structures existed in the granule interior. Combined with the Scanning Electron Microscope images of dry granules, it was found that the granules were comprised of hollow sub-granules. Since the biomass in the reactor increased with no obvious increase in the granule size, it was inferred that the hollow sub-granules had fragile connections with each other and that granules division occurred easily, resulting in the high dispersity of sludge. Florescence in situ hybridization results also showed that the ammonium-oxidizing bacteria and anammox bacteria were mainly distributed in the two sides of the sub-granule shells and the HAP in the middle. This kind of structure raised the density of granules and improved the settleability of sludge, which made it possible to achieve a high biomass in the reactor at a short HRT. Therefore, the sludge formed in the reactor was concentrated, highly dispersive and easily settleable. These factors appear to be crucial for achieving the desired nitrogen removal performance. This study marks a big leap in LSAWW treatment through the one-stage PNA process and has great potential in actual applications.

Recovered granular sludge extracellular polymeric substances as carrier for bioaugmentation of granular sludge reactor

An increasing amount of industrial chemicals are being released into wastewater collection systems and indigenous microbial communities in treatment plants are not always effective for their removal. In this work, extracellular polymeric substances (EPS) recovered from aerobic granular sludge (AGS) were used as a natural carrier to immobilize a specific microbial strain, Rhodococcus sp. FP1, able to degrade 2-fluorophenol (2-FP). The produced EPS granules exhibited a 2-FP degrading ability of 100% in batch assays, retaining their original activity after up to 2-months storage. Furthermore, EPS granules were added to an AGS reactor intermittently fed with saline wastewater containing 2-FP. Degradation of 2-FP and stoichiometric fluorine release occurred 8 and 35 days after bioaugmentation, respectively. Chemical oxygen demand removal was not significantly impaired by 2-FP or salinity loads. Nutrients removal was impaired by 2-FP load, but after bioaugmentation, the phosphate and ammonium removal efficiency improved from 14 to 46% and from 25 to 42%, respectively. After 2-FP feeding ceased, at low/moderate salinity (0.6-6.0 g L^-1 NaCl), ammonium removal was completely restored, and phosphate removal efficiency increased. After bioaugmentation, 11 bacteria isolated from AGS were able to degrade 2-FP, indicating that horizontal gene transfer could have occurred in the reactor. The improvement of bioreactor performance after bioaugmentation with EPS immobilized bacteria and the maintenance of cell viability through storage are the main advantages of the use of this natural microbial carrier for bioaugmentation, which can benefit wastewater treatment processes.

Enhancement of nitrite-dependent anaerobic methane oxidation via Geobacter sulfurreducens

Nitrite-dependent anaerobic methane-oxidation (n-damo) is a potential novel technology for nitrogen removal in anaerobic wastewater treatment. In this study, Geobacter sulfurreducens (G) was applied to stimulate n-damo activity. Conductive materials such as nano-magnetite (M) or aggregating agents such as hydroxylapatite (H) were co-added with G. sulfurreducens to further investigate the enhancement effect. Results showed that the nitrite reduction activity of the n-damo culture was promoted by G. sulfurreducens, with 1.71-2.38 times higher in treatment G, G + M, and G + H than that in the control, but was inhibited by the single addition of hydroxylapatite. N-damo bacterial abundances based on the qPCR of the n-damo-specific pmoA gene increased in treatments with G. sulfurreducens, compared with that of the control. High-throughput sequencing analysis revealed the enrichment of uncultured phylum WPS-2 in treatments with G. sulfurreducens. Fluorescence in situ hybridization verified the co-occurrence pattern of n-damo bacteria (NC10), G. sulfurreducens, and type-I aerobic methanotrophs (Methylomonas spp.). The above results corroborated the microbial interspecies electron transfer (MIET) potentiality of the n-damo enrichment. Our study provides a novel pathway for enhancing MIET to stimulate n-damo process.

Formation Mechanism of hydroxyapatite encapsulation in Anammox-HAP Coupled Granular Sludge

The potential of the formation of anammox-hydroxyapatite (HAP) granule composites as a cost-effective approach to removing nitrogen and phosphorus in the treatment of wastewater has been recently reported. Before these annamox granules, which consist of an anammox biofilm layer and an HAP crystallizing layer, can be used in applications, the formation mechanism of hydroxyapatite (HAP) encapsulation in the granules needs to be further studied. In this work, the role of extracellular polymeric substance (EPS) secreted by microorganisms and HAP core in Ca and P removal in anammox-HAP coupled granular sludge was investigated. According to the Lamer model, it is possible that the nucleation time of the granules becomes shorter as the crystal seeds. The enhanced buffering capacity of the granules was 0.08 mmol-H⁺ SS-g^-1 with the pH kept above 6.5 for a comfortable environment for anammox. The results of this study show that ion competition and exchange, mainly between cations of Ca²⁺ and Mg²⁺ and between anions of PO₄^3- and CO₃^2-, affects the precipitation process. The results of this study indicate that the addition of granule crystal seeds can be used as a strategy to hasten the anammox process, and therefore accelerate the overall process.

Deciphering nitrogen removal mechanism through marine anammox bacteria treating nitrogen-laden saline wastewater under various phosphate doses: Microbial community shift and phosphate crystal

The effect of phosphate on marine anammox bacteria (MAB)-dominated anammox process in nitrogen-laden saline wastewater was first investigated. The activity of MAB was enhanced by dosing low concentrations of phosphate (5-30 mg/L PO₄^3--P), and the time of complete ammonium removal was shortened by 0.5 h. When PO₄^3--P exceeded 160 mg/L, the calcium magnesium phosphate precipitation was formed in the reactor. The contact between substrates and biomass was hindered by the sediments, and the nitrogen removal performance of MAB was also worsened. At 400 mg/L PO₄^3--P, the ammonium removal rate and nitrite removal rate decreased to 0.45 and 0.43 kg/(m³⋅d), respectively. During the 158-day operation, MAB was still the dominant strain, but its relative abundance decreased by 15.4% at 400 mg/L PO₄^3--P. Besides, the presence of sediments stimulated the production of extracellular polymeric substances and the maximum yield reached 11.25 mg/g⋅wet weight at 200 mg/L PO₄^3--P.

Phosphorus recovery via the formation of hydroxyapatite crystals at various nitrogen loading rate in an anammox-based UAFB

A strategy that integrates the anammox and hydroxyapatite crystallization in an up-flow anaerobic fixed-bed reactor (UAFB) was investigated to simultaneously remove nitrogen and recover phosphorus. During the 430 days of operation, 73.1 ± 6.6% of influent phosphorus was removed with an efficient nitrogen removal efficiency of 87.8 ± 1.7%. After long-term operation, numerous acicular and micron-sized crystals were observed on the matured biofilm, of which the phosphorus content was around 10.21% (wt%) and hydroxyapatite was the main form of crystals through SEM-EDS, FT-IR and XRD analysis. The variation of substrates along the axial length of UAFB showed that phosphate removal was positively correlated with anammox and pH. Moreover, three anammox bacteria including Candidatus Brocadia (19.73%), Candidatus Jettenia (0.49%) and Candidatus Kuenenia (0.85%) were detected at the bottom of UAFB, while Candidatus Jettenia (4.67%) was dominant at the top. Hence, the anammox-based biofilm system could be alternative for the recovery of phosphorus from nutrient-rich wastewater.

Critical Analysis of Biomass Retention Strategies in Mainstream and Sidestream ANAMMOX-Mediated Nitrogen Removal Systems

ANAMMOX (anaerobic ammonium oxidation) represents an energy-efficient process for biological nitrogen removal, particularly from wastewater streams with low chemical oxygen demand (COD) to nitrogen (C/N) ratios. Its widespread application, however, is still hampered by a lack of access to biomass-enriched with ANAMMOX bacteria (AMX), slow growth rates of AMX, and their sensitivity to inhibition. Although the coupling of ANAMMOX processes with partial nitrification is already widespread, especially for sidestream treatment, maintaining a functional population density of AMX remains a challenge in these systems. Therefore, strategies that maximize retention of AMX-rich biomass are essential to promote process stability. This paper reviews existing methods of biomass retention in ANAMMOX-mediated systems, focusing on (i) granulation; (ii) biofilm formation on carrier materials; (iii) gel entrapment; and (iv) membrane technology in mainstream and sidestream systems. In addition, the microbial ecology of different ANAMMOX-mediated systems is reviewed.

Hydroxyapatite crystallization-based phosphorus recovery coupling with the nitrogen removal through partial nitritation/anammox in a single reactor

For digestion effluent treatment, while the anammox-based process has been successfully applied for nitrogen removal, in most cases, phosphorus (P) represents another major concern. In this study, a novel process, integrating the partial nitritation/anammox and hydroxyapatite crystallization (PNA-HAP) in a single airlift reactor, was developed for the simultaneous nitrogen removal and P recovery from synthetic digestion effluent. With a stable influent P concentration of 20.0 mg/L, an HRT of 6 h, and alternating increases of influent calcium and ammonium, the final achieved nitrogen removal rate was 1.2 kg/m³/d and the P removal efficiency was 83.0%. The settleability of sludge was desirably enhanced with the calcium addition and a high biomass concentration was achieved in reactor. Quantitative and qualitative analyses confirmed that HAP was the main inorganic content in sludge, which could be harvested for P recovery. According to the Scanning Electron Microscope observation and the Energy Dispersive X-ray spectrometry analysis, the microbes were mainly distributed on the outer layer of the sludge aggregate, while the HAP mainly in the interior. The relevant theoretical calculation also revealed that the sludge discharge manipulation has direct effect on the sludge composition and aggregate structure. In sum, the results are evidence of the feasibility of simultaneous nitrogen removal and P recovery through one-stage PNA-HAP process for digestion effluent.

Bulking and floatation of the anammox-HAP granule caused by low phosphate concentration in the anammox reactor of expanded granular sludge bed (EGSB)

The effect of phosphate concentration on the anammox-HAP process was investigated in this work. A high total nitrogen removal efficiency (>82.6%) and a stable total phosphate removal efficiency (>56.2%) was achieved in reactor with the phosphate concentration over 11.4 mg L^-1. However, a phosphate concentration below to 5.7 mg L^-1, a floatation of sludge occurred caused the deterioration of process. A new understanding for the floatation was divided into three stages: the stable stage, bulking stage and floating stage. First, anammox biofilm coupled with HAP for granulation in the stable stage. Second, the aggregation of bulking sludge resulted in changes in viscoelastic properties of the sludge. Third, the floatation resulted from unreleasable gas bubbles in the granules wrapped a high concentrations of slime layer proteins. Overall, this paper suggests that a control strategy was a sufficient supply of phosphate for the stable operation.

Simultaneous nitrogen removal and phosphorus recovery using an anammox expanded reactor operated at 25 °C

While anammox is a cost-effective nitrogen treatment process for wastewater with high nutrient strength, phosphorus remains untouched during this process and needs further treatment. In this study, the nitrogen removal and phosphorus recovery were achieved simultaneously at 25 °C using an anammox expanded bed. A stable high nitrogen removal efficiency of 83.7 ± 4.8% at a 1500 mgN/L influent total nitrogen concentration and a phosphorus removal efficiency of 94.2 ± 1.2% at 100 mg P/L influent total phosphorus were obtained during continuous operation. The effects of the nitrogen loading rate, hydraulic retention time (HRT), pH, Ca²⁺ and PO₄^3- concentration on the phosphorus removal was verified in the long-term operation of the reactor. The sludge produced contained a high content of phosphorus mainly in the form of hydroxyapatite (HAP), and the sludge composition strongly reflected the nitrogen and phosphorus loading. The structure of the anammox-HAP composite granules was illustrated by the use of fluorescence in situ hybridization (FISH) and Raman spectroscopic mapping analysis. The results in this study indicate that by controlling the operation parameters, it is possible to integrate a high efficiency phosphorus recovery with the anammox process, and significantly reduce the nutrient loading for further wastewater treatment.

Towards more efficient nitrogen removal and phosphorus recovery from digestion effluent: Latest developments in the anammox-based process from the application perspective

Over the past forty years, anammox-based processes have been extensively researched and applied to some extent. However, some of the long-standing problems present serious impediments to wide application of these processes, and knowledge gap between lab-scale research and full-scale operations is still considerable. In recent years, anammox-based research has developed rapidly and some emerging concepts have been proposed. The focus of this review is on the critical problems facing actual application of anammox processes. The latest developments in anammox-based processes are summarized, and particular consideration is given to the following aspects: (1) the evolution of the chemical stoichiometry of anammox reaction; (2) the status of several main anammox-based processes; (3) the critical problems and countermeasures; (4) the emerging anammox-based processes; and (5) the suggested optimal process integrating partial nitritation, anammox, hydroxyapatite crystallization and denitratation for digestion effluent treatment towards more efficient nitrogen removal and phosphorus recovery in the future.

Extracellular protein isolation from the matrix of anammox biofilm using ionic liquid extraction

Anaerobic ammonium oxidation (anammox)-performing bacteria self-assemble into compact biofilms by expressing extracellular polymeric substances (EPS). Anammox EPS are poorly characterized, largely due to their low solubility in typical aqueous solvents. Pronase digestion achieved 19.5 ± 0.9 and 41.4 ± 1.4% (w/w) more solubilization of laboratory enriched Candidatus Brocadia sinica anammox granules than DNase and amylase, respectively. Nuclear magnetic resonance profiling of the granules confirmed proteins as dominant biopolymer within the EPS. Ionic liquid (IL) 1-ethyl-3-methylimidazolium acetate and N,N-dimethylacetamide (EMIM-Ac/DMAc) mixture was applied to extract the major structural proteins. Further treatment by anion exchange chromatography isolated homologous serine (S)- and threonine (T)-rich proteins BROSI_A1236 and UZ01_01563, which were major components of the extracted proteins, and sequentially highly similar to putative anammox extracellular proteins KUSTD1514 and WP_070066018.1 of Ca. Kuenenia stuttgartiensis and Ca. Brocadia sapporoensis, respectively. Six monosaccharides (i.e., arabinose, xylose, rhamnose, fucose, galactose, and mannose) were enriched for BROSI_A1236 against all other major proteins. The sugars, however, contributed < 0.5% (w/w) of total granular biomass and were likely co-enriched as glycoprotein appendages. This study demonstrates that BROSI_A1236 is a major extracellular component of Ca. B. sinica anammox biofilms that is likely a common anammox extracellular polymer, and can be isolated from the matrix following ionic liquid extraction.

Solubilization and characterization of extracellular proteins from anammox granular sludge

Elucidating the extracellular polymeric substances (EPS) of anammox granular sludge is important for stable nitrogen removal processes in wastewater treatment. However, due to a lack of standardized methods for extraction and characterization, the composition of anammox granule EPS remains mostly unknown. In this study, alkaline (NaOH) and ionic liquid (IL) extractions were compared in terms of the proteins they extracted from different "Candidatus Brocadia" cultures. We aimed to identify structural proteins and evaluated to which extend these extraction methods bias the outcome of EPS characterization. Extraction was focussed on solubilization of the EPS matrix, and the NaOH and IL extraction recovered on average 20% and 26% of the VSS, respectively. Using two extraction methods targeting different intermolecular interactions increased the possibility of identifying structural extracellular proteins. Of the extracted proteins, ∼40% were common between the extraction methods. The high number of common abundant proteins between the extraction methods, illustrated how extraction biases can be reduced when solubility of the granular sludge is enhanced. Physicochemical analyses of the granules indicated that extracellular structural matrix proteins likely have β-sheet dominated secondary structures. These β-sheet structures were measured in EPS extracted with both methods. The high number of uncharacterized proteins and possible moonlighting proteins confounded identifying structural (i.e. β-sheet dominant) proteins. Nonetheless, new candidates for structural matrix proteins are described. Further current bottlenecks in assigning specific proteins to key extracellular functions in anammox granular sludge are discussed.

Thermal pretreatment to enhance biogas production of waste aerobic granular sludge with and without calcium phosphate precipitates

To develop aerobic granules based sustainable wastewater treatment, it is necessary to view wastewater treatment process and excess sludge treatment as a whole to evaluate resource recovery and sustainability. We thus investigated in this study how mineral characteristics of aerobic granules with/without calcium phosphate precipitates for phosphorus removal in treatment process affect the excess sludge digestion for energy recovery. Steam explosion at 170 °C as an effective thermal sludge treatment approach was studied in parallel with normal thermal treatment in an autoclave at 70, 100 and 125 °C, respectively. A liner relationship was found between the thermal treatment temperature in the autoclave and biogas production of aerobic granules. The untreated granules with only 10% mineral content (G1) generated 30% more biogas than the untreated granules with 39% mineral content (G2), but steam explosion is more effective to G2 with high mineral content and relatively poor methane yield potential. In addition, steam explosion improved methane production from G2 more compared with activated sludge although both untreated activated sludge and G2 had comparable methane production, i.e. around 0.235 L CH₄/g VS. Therefore, steam explosion is potential to be used to increase methane production especially when the untreated granular sludge has low methane yield due to high mineral content. This work provides a good basis for a holistic evaluation of resource recovery based on aerobic granular sludge, i.e. combined energy recovery and phosphorus removal and recovery via CaP precipitates, and trade-off between different factors with steam explosion.

Process optimization of anammox-driven hydroxyapatite crystallization for simultaneous nitrogen removal and phosphorus recovery

Based on the requirements for advanced treatment and resource recovery of nitrogen and phosphorus pollutants in wastewater, the coupled anammox and hydroxyapatite crystallization (anammox-HAP) process was studied with an aim of achieving high efficiency and low energy consumption during simultaneous nitrogen and phosphorus removal. In the long-term experiments and batch tests, the effects of substrate conditions (nitrogen and phosphorus load, calcium concentration, etc.) on the nitrogen removal and phosphorus recovery efficiencies were investigated. The granular structure and crystal properties were analyzed together with microscopic characterization methods, and the formation mechanism of coupled anammox-HAP granules was verified. Based on these experiments, a theoretical model and technical method for realizing the coupled process were established, and a reference for practical engineering application was provided.

Enhanced aerobic granulation by applying the low-intensity direct current electric field via reactive iron anode

A novel granulation strategy by applying the low-intensity direct current (DC) electric field via reactive iron anode into the aerobic granular sludge (AGS) system was systematically investigated in this study. Three identical sequencing batch reactors (SBRs, namely R1, R2, and R3) were operated for 100 days. Comparatively, the R1 and R3 were continuously subjected to the 1.0 V DC electric field via a reactive Fe anode and an inert Ti-Ir/Rh anode, respectively, while the R2 without DC exposure. The results showed that the sludge granulation processes were accelerated in order as follows: R2<R3<R1, and the properties of mature granules were improved in order as follows: R3<R2<R1. Interestingly, at the end of experiment, total phosphorus (TP) removal efficiency in R1 dramatically increased to 80.52%, which was 2.15 and 1.96 folds than that in R2 and R3, respectively. Further investigations revealed that this novel strategy could simultaneously improve the secretion of EPS and the release of iron ions in R1, which cooperatively enhanced the granulation process. Moreover, in R1, mineral precipitation of phosphate remarkably improved the capability of phosphorus removal. The observed effective and stable performance highlights the feasibility and potential of this novel strategy for the rapid start-up and stable operation of AGS system.

Microbial communities associated with phosphogenic sediments and phosphoclast-associated DNA of the Benguela upwelling system

The processes that lead to the precipitation of authigenic calcium phosphate minerals in certain marine pore waters remain poorly understood. Phosphogenesis occurs in sediments beneath some oceanic upwelling zones that harbor polyphosphate-accumulating bacteria. These bacteria are believed to concentrate phosphate in sediment pore waters, creating supersaturated conditions with respect to apatite precursors. However, the relationship between microbes and phosphorite formation is not fully resolved. To further study this association, we examined microbial community data generated from two sources: sediment cores recovered from the shelf of the Benguela upwelling region where phosphorites are currently forming, and DNA preserved within phosphoclasts recovered from a phosphorite deposit along the Benguela shelf. iTag and clone library sequencing of the 16S rRNA gene showed that many of our sediment-hosted communities shared large numbers of phylotypes with one another, and that the same metabolic guilds were represented at localities across the shelf. Sulfate-reducing bacteria and sulfur-oxidizing bacteria were particularly abundant in our datasets, as were phylotypes that are known to carry out nitrification and the anaerobic oxidation of ammonium. The DNA extracted from phosphoclasts contained the signature of a distinct microbial community from those observed in the modern sediments. While some aspects of the modern and phosphoclast communities were similar, we observed both an enrichment of certain common microbial classes found in the modern phosphogenic sediments and a relative depletion of others. The phosphoclast-associated DNA could represent a relict signature of one or more microbial assemblages that were present when the apatite or its precursors precipitated. While these taxa may or may not have contributed to the precipitation of the apatite that now hosts their genetic remains, several groups represented in the phosphoclast extract dataset have the genetic potential to metabolize polyphosphate, and perhaps modulate phosphate concentrations in pore waters where carbonate fluorapatite (or its precursors) are known to be precipitating.

Nutrient recovery technologies integrated with energy recovery by waste biomass anaerobic digestion

Anaerobic digestion widely considered as a promising waste biomass disposal treatment approach, is attracting increasing interest in all corners of the globe. However, due to the specific features of different types of waste biomass, the bioenergy conversion efficiency of this process is not ideal. Another problematic aspect of anaerobic digestion is that the nutrient rich effluent sometimes needs to be treated before discharge. This review presents the recent achievements of waste biomass digestion from the perspective of energy recovery and nutrient recovery. In this work, the anaerobic treatment characteristics of common types of waste biomass are summarized and compared. With a focus of nutrient recovery and post treatment issues, the challenges and technical hurdles encountered in the anaerobic digestion of waste biomass are critically reviewed. Finally, an integrated system of anaerobic digestion, anaerobic ammonia oxidation (anammox) and phosphorus recovery is proposed for efficient energy and nutrient recovery from waste biomass.

A new process for simultaneous nitrogen removal and phosphorus recovery using an anammox expanded bed reactor

Phosphorus recovery from wastewater is an important approach for sustainable phosphorus use. In this work, a process combining anammox and hydroxyapatite (HAP) precipitation in an expanded bed reactor for simultaneous nitrogen removal and phosphorus recovery was developed by applying specific Ca/P ratio and pH control. A high phosphorus removal rate (0.14 ± 0.01 kg-P/m³/d) was obtained while a stable nitrogen removal efficiency (87.4 ± 2.9%) maintained with an effluent recirculation system applied. Average 13.4% phosphorus (30.7% in P₂O₅) accumulation in the dry sludge and a Ca/P ratio very close to HAP was observed by quantitative elemental analysis. In this work, different analysis revealed the two layers structure with anammox biofilm attached to inorganic core of the granules. Different spectral analysis determined the major phase of the inorganic content as hydroxyapatite. With proper Ca/P ratio and pH control, anammox expanded bed reactor was transformed into an efficient process to simultaneously remove nitrogen and recover phosphorus.

Aggregation ability of three phylogenetically distant anammox bacterial species

Anaerobic ammonium-oxidizing (anammox) bacteria are well known for their aggregation ability. However, very little is known about cell surface physicochemical properties of anammox bacteria and thus their aggregation abilities have not been quantitatively evaluated yet. Here, we investigated the aggregation abilities of three different anammox bacterial species: "Candidatus Brocadia sinica", "Ca. Jettenia caeni" and "Ca. Brocadia sapporoensis". Planktonic free-living enrichment cultures of these three anammox species were harvested from the membrane bioreactors (MBRs). The physicochemical properties (e.g., contact angle, zeta potential, and surface thermodynamics) were analyzed for these anammox bacterial species and used in the extended DLVO theory to understand the force-distance relationship. In addition, their extracellular polymeric substances (EPSs) were characterized by X-ray photoelectron spectroscopy and nuclear magnetic resonance. The results revealed that the "Ca. B. sinica" cells have the most hydrophobic surface and less hydrophilic functional groups in EPS than other anammox strains, suggesting better aggregation capability. Furthermore, aggregate formation and anammox bacterial populations were monitored when planktonic free-living cells were cultured in up-flow column reactors under the same conditions. Rapid development of microbial aggregates was observed with the anammox bacterial population shifts to a dominance of "Ca. B. sinica" in all three reactors. The dominance of "Ca. B. sinica" could be explained by its better aggregation ability and the superior growth kinetic properties (higher growth rate and affinity to nitrite). The superior aggregation ability of "Ca. B. sinica" indicates significant advantages (efficient and rapid start-up of anammox reactors due to better biomass retention as granules and consequently stable performance) in wastewater treatment application.

Microstructure of anammox granules and mechanisms endowing their intensity revealed by microscopic inspection and rheometry

The anammox process represents a sustainable and cost-effective technique for nitrogen removal from wastewater, where granulation of anammox bacteria could be of great benefit to the system performance. However, knowledge of the specific properties of anammox granules is currently unsatisfactory. In this study, the organization of anammox granules was comprehensively studied from macro to micro scale with a range of microscale techniques. Scanning and transmission electron microscopy and multiple fluorescence labeling combined with confocal laser scanning microscopy were included. Simultaneously, the associated mechanical properties were studied in-depth by rheometry in combination with selective enzymatic hydrolysis. Anammox granules follow a tertiary organization regime, where interactions between individual anammox bacteria made up the primary base, then, the grouping of anammox bacterial cells encapsulated within a thin extracellular polymeric substance (EPS) layer comprised a second arrangement level, and, finally, the cementing of these groups together with other bacteria and polymers gave rise to compact aggregates. α-Polysaccharides and proteins were considered the backbones of anammox granules, contributing greatly to their excellent intensity. β-Polysaccharides concentrated at the outer rims of anammox granules and combined with other macromolecules to form a buffer zone or protective barrier, beneath which anammox bacteria proliferated. Divalent cationic bridging for EPS binding was prevalent and of great significance within the dense anammox granules, while there was also much weak monovalent ionic interaction. The specific organization and composition of anammox granules endows them with excellent intensity and integrity, which can be of importance for full-scale reactor operations where diverse shocks can be expected.

Seawater-based wastewater accelerates development of aerobic granular sludge: A laboratory proof-of-concept

This study aimed to develop an aerobic granular sludge process for the efficient treatment of highly saline wastewater and understand the granulation process in a seawater-based multi-ion matrix. Five identical sequencing batch airlift reactors (SBARs) are used to treat synthetic saline sewage with different proportions of real seawater (0%-100%). The results confirm that aerobic granular sludge can be successfully developed with various proportions of seawater up to 100% and show that seawater not only significantly accelerates granulation but also generates stronger granular structures than does freshwater. The increased presence of gel-forming alginate-like exopolysaccharides in the granules explains why a greater proportion of seawater leads to higher density and improves the cohesive strength of the granules. SEM-EDX analysis further revealed substantial presence of both Ca²⁺ and Mg²⁺ phosphate in the granule core as well as in the outer layers providing extra bridging forces in addition to alginate-like exopolysaccharides for accelerating the granule formation and maintaining the structure. It is hoped that this work could explore another approach for saline sewage treatment and bring some clues for the mystery of granulation mechanism.

Anammox biofilm in activated sludge swine wastewater treatment plants

We investigated anammox with a focus on biofilm in 10 wastewater treatment plants (WWTPs) that use activated sludge treatment of swine wastewater. In three plants, we found red biofilms in aeration tanks or final sedimentation tanks. The biofilm had higher anammox 16S rRNA gene copy numbers (up to 1.35 × 10¹² copies/g-VSS) and higher anammox activity (up to 295 μmoL/g-ignition loss/h) than suspended solids in the same tank. Pyrosequencing analysis revealed that Planctomycetes accounted for up to 17.7% of total reads in the biofilm. Most of them were related to Candidatus Brocadia or Ca. Jettenia. The highest copy number and the highest proportion of Planctomycetes were comparable to those of enriched anammox sludge. Thus, swine WWTPs that use activated sludge treatment can fortuitously acquire anammox biofilm. Thus, concentrated anammox can be detected by focusing on red biofilm.

Strengthening aerobic granule by salt precipitation

Structural stability of aerobic granules is generally poor during long-term operation. This study precipitated seven salts inside aerobic granules using supersaturated solutions of (NH4)3PO4, CaCO3, CaSO4, MgCO3, Mg3(PO4)2, Ca3(PO4)2 or SiO2 to enhance their structural stability. All precipitated granules have higher interior strength at ultrasonic field and reveal minimal loss in organic matter degradation capability at 160-d sequential batch reactor tests. The strength enhancement followed: Mg3(PO4)2=CaSO4>SiO2>(NH4)3PO4>MgCO3>CaCO3=Ca3(PO4)2>original. Also, the intra-granular solution environment can be buffered by the precipitate MgCO3 to make the aerobic granules capable of degradation of organic matters at pH 3. Salt precipitation is confirmed a simple and cost-effective modification method to extend the applicability of aerobic granules for wastewater treatments.

Insight into the short- and long-term effects of inorganic phosphate on anammox granule property

The short- and long-term effects of inorganic phosphate on property of anaerobic ammonium oxidation (anammox) granule were investigated in this study. Acute exposure to high-level phosphate (⩾50 mM) induced the cytoplasm leakage. During a 195-day continuous-flow operation, the gradually increasing phosphate (up to 500 mgP L(-1)) slightly affected the specific anammox activity, hardly impacted the heme c content, remarkably decreased the extracellular polymeric substances production and significantly stimulated the dehydrogenase activity of anammox granules. Microbial community analysis showed no shift in the dominant anammox strain and higher population but lower relative abundance of anaerobic ammonium-oxidizing bacteria compared to the control granules. Interestingly, novel anammox granules with a hydroxyapatite core were cultivated, which possessed excellent settleability, huge granule diameter and superior mechanical strength. This study supported the application of granule-based anammox process as a pre-processing treatment in phosphate-containing and ammonia-rich wastewaters.

Rapid and successful start-up of anammox process by immobilizing the minimal quantity of biomass in PVA-SA gel beads

Rapid start-up of anaerobic ammonium oxidation (anammox) process in up-flow column reactors was successfully achieved by immobilizing minimal quantity of biomass in polyvinyl alcohol (PVA)-sodium alginate (SA) gel beads. The changes in the reactor performance (i.e., nitrogen removal rate; NRR) were monitored with time. The results demonstrate that the reactor containing the immobilized biomass concentration of 0.33 g-VSS L(-1) achieved NRR of 10.8 kg-N m(-3) d(-1) after 35-day operation, whereas the reactor containing the granular biomass of 2.5 g-VSS L(-1) could achieve only NRR of 3.5 kg-N m(-3) d(-1). This indicates that the gel immobilization method requires much lower seeding biomass for start-up of anammox reactor. To explain the better performance of the immobilized biomass, the biological and physicochemical properties of the immobilized biomass were characterized and compared with the naturally aggregated granular biomass. Effective diffusion coefficient (De) in the immobilized biomass was directly determined by microelectrodes and found to be three times higher than one in the granular biomass. High anammox activity (i.e., NH4(+) and NO2(-) consumption rates) was evenly detected throughout the gel beads by microelectrodes due to faster and deeper substrate transport. In contrast, anammox activity was localized in the outer layers of the granular biomass, indicating that the inner biomass could not contribute to the nitrogen removal. This difference was in good agreement with the spatial distribution of microbes analysed by fluorescence in situ hybridization (FISH). Based on these results, PVA-SA gel immobilization is an efficient strategy to initiate anammox reactors with minimal quantity of anammox biomass.

Microbial community composition and ultrastructure of granules from a full-scale anammox reactor

Granules in anammox reactors contain besides anammox bacteria other microbial communities whose identity and relationship with the anammox bacteria are not well understood. High calcium concentrations are often supplied to anammox reactors to obtain sufficient bacterial aggregation and biomass retention. The aim of this study was to provide the first characterization of bacterial and archaeal communities in anammox granules from a full-scale anammox reactor and to explore on the possible role of calcium in such aggregates. High magnification imaging using backscattered electrons revealed that anammox bacteria may be embedded in calcium phosphate precipitates. Pyrosequencing of 16S rRNA gene fragments showed, besides anammox bacteria (Brocadiacea, 32%), substantial numbers of heterotrophic bacteria Ignavibacteriacea (18%) and Anaerolinea (7%) along with heterotrophic denitrifiers Rhodocyclacea (9%), Comamonadacea (3%), and Shewanellacea (3%) in the granules. It is hypothesized that these bacteria may form a network in which heterotrophic denitrifiers cooperate to achieve a well-functioning denitrification system as they can utilize the nitrate intrinsically produced by the anammox reaction. This network may provide a niche for the proliferation of archaea. Hydrogenotrophic methananogens, which scavenge the key fermentation product H2, were the most abundant archaea detected. Cells resembling the polygon-shaped denitrifying methanotroph Candidatus Methylomirabilis oxyfera were observed by electron microscopy. It is hypothesized that the anammox process in a full-scale reactor triggers various reactions overall leading to efficient denitrification and a sink of carbon as biomass in anammox granules.

Magnesium carbonate precipitate strengthened aerobic granules

Aerobic granules were precipitated internally with magnesium carbonate to enhance their structural stability under shear. The strengthened granules were tested in continuous-flow reactors for 220 days at organic loadings of 6-39 kg/m(3)/day, hydraulic retention times of 0.44-19 h, and temperatures of 10 or 28°C. The carbonate salt had markedly improved the granule strength without significant changes in granule morphology or microbial communities (with persistent strains Streptomyces sp., Rhizobium sp., Brevundimonas sp., and Nitratireductor sp.), or sacrifice in biological activity for organic degradation. MgCO3 precipitated granules could be used in continuous-flow reactor for wastewater treatment at low cost and with easy processing efforts.

Combined biofouling and scaling in membrane feed channels: a new modeling approach

A mathematical model was developed for combined fouling due to biofilms and mineral precipitates in membrane feed channels with spacers. Finite element simulation of flow and solute transport in two-dimensional geometries was coupled with a particle-based approach for the development of a composite (cells and crystals) foulant layer. Three fouling scenarios were compared: biofouling only, scaling only and combined fouling. Combined fouling causes a quicker flux decline than the summed flux deterioration when scaling and biofouling act independently. The model results indicate that the presence of biofilms leads to more mineral formation due to: (1) an enhanced degree of saturation for salts next to the membrane and within the biofilm; and (2) more available surface for nucleation to occur. The impact of biofilm in accelerating gypsum precipitation depends on the composition of the feed water (eg the presence of NaCl) and the kinetics of crystal nucleation and growth. Interactions between flow, solute transport and biofilm-induced mineralization are discussed.

The performance of high-loading composite anammox reactor and its long-term recovery from extreme substrates inhibition

A composite reactor combined with granule and biofilm in one single SBR was developed for high-rate anammox operation. Low activity flocculent inoculum was used as seed sludge and the nitrogen loading rate reached 10.62kgNm(-3)d(-1) after 93days' operation. Subsequently, the performance of high-loading anammox reactor under fluctuation condition was investigated. Due to the extremely short hydraulic retention time and high-strength substrates, the reactor presented dramatic substrates accumulation which resulted in severe inhibition subsequently. Nevertheless, the composite reactor presented significant recovery potential even after biomass hydrolysis caused by inhibition, mainly due to the protection and promotion supplied by biofilm. Besides, granules were gradually formed and accumulated from the flocculent sludge directly during the recovery operation, further elevating the reactor performance. The nitrogen loading rate and corresponding nitrogen removal rate achieved 20.30 and 18.01kgNm(-3)d(-1) with total nitrogen in the influent of 1500mg/l finally.

A comparative study of abiological granular sludge (ABGS) formation in different processes for zinc removal from wastewater

Abiological granular sludge (ABGS) formation is a potential and facile strategy for improving sludge settling performance during zinc removal from wastewater using chemical precipitation. In this study, the effect of pH, seed dosage, and flocculant dosage on ABGS formation and treated water quality was investigated. Results show that settling velocity of ABGS can reach up to 4.00 cm/s under optimal conditions, e.g., pH of 9.0, zinc oxide (ZnO) seeds dosage of 1.5 g/l, and polyacrylamide (PAM) dosage of 10 mg/l. More importantly, ABGS formation mechanism was investigated in NaOH precipitation process and compared with that in bio-polymer ferric sulfate (BPFS)-NaOH precipitation process regarding their sludge structure and composition. In the NaOH precipitation process, ABGS formation depends on some attractions between particles, such as van der Waals attraction and bridging attraction. However, during the BPFS-NaOH sludge formation process, steric repulsion becomes dominant due to the adsorption of BPFS on ZnO seeds. This repulsion further causes extremely loose structure and poor settling performance of BPFS-NaOH sludge.