On techniques for the measurement of the mass fractal dimension of aggregates

HKUST-1 MOF nanoparticles: a non-classical crystallization route in supercritical CO2

Reducing MOF particles to the nanoscale size range is beneficial due to their increased surface-to-volume ratio, higher defects exposing metals and ligands, and short diffusion path. While great efforts have been made to reduce the particle sizes by controlling the reaction kinetics or terminating the particle growth, large-scale, rapid synthesis of MOF nanoparticles (NPs) remains a challenge. Here, we report supercritical (sc) CO2-assisted synthesis of HKUST-1 NPs in a continuous flow reactor, which yielded pure and thermally stable MOFs with median sizes of 110-250 nm and BET surface areas of 1610-1890 m2 g-1 under 10 seconds synthesis time. ScCO2 and ethanol with a molar ratio of 9 : 1 are used as co-solvents for the fast nucleation of HKUST-1 and crystal formation. A typical dry yield of 53.7 wt% is achieved with 0.1 M Cu precursor under mild conditions at 75 °C and 13 MPa. The space-time yields and surface area production rates are 5668 kg m-3 d-1 and 1.0 × 1010 m2 m-3 d-1. Particle size and morphology analyses indicate that aggregation of nascent structures occurs in the aerosolized state, leading to a non-classical crystal growth mechanism and enabling multiple pathways for tuning the synthesis process. With the ability to recycle CO2, solvents, and unreacted precursors, the method can be used for the scalable production of MOFs.

Predicting a Wide Range of Fractal Dimensions of Salt-Induced Aggregates in Water Using a Random Forest Model

Salt-induced colloidal aggregates can significantly influence contaminant fate and transport in natural and engineered systems. These aggregates' fractal dimensions (df), ranging from 1.4 to 2.2, depend on various system variables. However, the quantitative relationship between these variables and df of aggregates has not been fully explored, especially in predicting a wide range of df. Here, we developed a random forest model capable of predicting the complete range of aggregate df using just four simple physical and chemical parameters of the aggregating system as inputs. The model accurately predicts the df of aggregates formed by colloids of different sizes, ranging from nano to micro sizes, after being trained and tested on appropriate data sets. Ionic strength (IS) has the most significant influence on the df of aggregates formed by microsized particles followed by the relative hydrodynamic radius of aggregates (Rh/Rp), particle concentration (Cp), and primary particle radius (Rp). For aggregates formed by both nano- and microsized particles, IS still has a strong influence on the df, with the significance of Rp increasing. All four inputs are negatively correlated with predicting the df of aggregates. The predictions align well with the physical interpretations.

Production of Monodisperse Large Drop Emulsions by Means of High Internal Phase Pickering Emulsions-Processing and Formulation

High internal phase Pickering emulsions (HIPPE) have received significant research attention in the last two decades due to their potential for a wide range of applications. The appropriate processing of such high-viscosity emulsions, hundreds of times more viscous than that of the continuous phase, and the control of the final droplet size remain challenges to be tackled. Our research targeted this knowledge gap by examining the influence of the emulsion formulation and the processing conditions on the final droplet size. The dispersed phase fraction (100 cSt silicon oil) ranged between 75 and 80%. The emulsions were produced in a regular mixing tank equipped with a helical ribbon impeller rotating at a low speed (100-150 rpm). The effective viscosity of the continuous phase was obtained from the experimental torque measurements. The droplet size distributions were measured after emulsification and dilution in the continuous phases. It is shown that the capillary number obtained from the observed emulsification performance can help predict the final droplet size. Our approach provides a straightforward methodology to generate concentrated Pickering emulsions with controlled and predictable droplet size.

New Insights into the Formation of Aggregates of Bidisperse Nano- and Microplastics in Water Based on the Analysis of In Situ Microscopy and Molecular Simulation

Microplastics (MPs) and nanoplastics (NPs) in water pose a global threat to human health and the environment. To develop efficient removal strategies, it is crucial to understand how these particles behave as they aggregate. However, our knowledge of the process of aggregate formation from primary particles of different sizes is limited. In this study, we analyzed the growth kinetics and structures of aggregates formed by polystyrene MPs in mono- and bidisperse systems using in situ microscopy and image analysis. Our findings show that the scaling behavior of aggregate growth remains unaffected by the primary particle size distribution, but it does delay the onset of rapid aggregation. We also performed a structural analysis that reveals the power law dependence of aggregate fractal dimension (df) in both mono- and bidisperse systems, with mean df consistent with diffusion-limited cluster aggregation (DLCA) aggregates. Our results also suggest that the df of aggregates is insensitive to the shape anisotropy. We simulated molecular forces driving aggregation of polystyrene NPs of different sizes under high ionic strength conditions. These conditions represent salt concentration in ocean water and wastewater, where the DLVO theory does not apply. Our simulation results show that the aggregation tendency of the NPs increases with the ionic strength. The increase in the aggregation is caused by the depletion of clusters of ions from the NPs surface.

Proposal for New Method for Calculating Sedimentation Process Efficiency in Water Treatment Plants

An important aspect of water treatment is removing fine-grain materials from water. Due to the properties of fine-grain materials, they are difficult to remove from water. During the sedimentation process, which takes place in settling tanks, such materials are removed. The sedimentation process is often accompanied by coagulation and flocculation processes, which form aggregates of particles (flocs) from the fine-grained material particles in a suspension (non-grainy suspension). This kind of suspension (consisting of aggregates of particles or flocs) shows a different behaviour when falling compared with classic grainy suspensions. The main goal and novelty of this article are to propose (and test) a modification of the often used Stokes' formula with the addition of fractal geometry into the calculation of the terminal velocity of free-falling particles in order to overcome Stokes' formula's limitation, thus obtaining the sedimentation process efficiency. Because of this fractal modification, it is possible to use the simple and elegant Stokes' formula in order to calculate better the terminal velocity of non-grainy particles-aggregates or flocs-and thus obtain the sedimentation efficiency for the whole range of suspensions, both non-grainy and grainy. The results obtained in this article show that the sedimentation process efficiency calculated by using the modified formula based on the fractal geometry morphology of particles (the proposed fractal method) describes and agrees more with the data from the experiment than the sedimentation efficiency calculated only based on particle size (classic method).

Comprehensive assessment of enhancing dewaterability of dredged sediments by starch-based flocculant

Dredged sediment poses significant challenges for transportation and subsequent treatment due to its high water content and large volume. Coagulation, a common method of dewatering, can significantly enhance the dewatering performance of dredged sediment. This study synthesized a cationic starch-based flocculant [starch-3-chloro-2-hydroxypropyl trimethylammonium chloride (St-CTA)] through etherification for the flocculation dewatering of dredged sediment. The effectiveness and mechanism of St-CTA as a dewatering flocculant for dredged sediment were investigated. The results demonstrated that when the dosage of St-CTA was 12 mg g-1 TSS (total suspended solids), the dehydration property of dredged sediment substantially improved, with the specific resistance to filtration (SRF) decreasing by 93.3%, the capillary suction time (CST) by 93.5%, and the water content of the filter cake (WC) by 9.7%. The removal rate of turbidity of the supernatant from the conditioned dredged sediment reached 99.6%, accelerating the settling speed and effectively capturing and separating fine particles from the sediment. St-CTA significantly increased the median particle size (D50), altered the microstructure and extracellular polymeric substances (EPS) of the flocs, and increased the fractal dimension of the flocs, making them more compact and conducive to the formation of drainage channels. These findings confirm the feasibility of using potentially environmentally friendly St-CTA as a rapid dewatering conditioning agent for sediment.

Navigating the microenvironment with flip and turn under quadrupole magnetophoretic steering control: Nanosphere- and nanorod-coated microbead

The spatiotemporal accuracy of microscale magnetophoresis has improved significantly over the course of several decades of development. However, most of the studies so far were using magnetic microbead composed of nanosphere particle for magnetophoretic actuation purpose. Here, we developed an in-house method for magnetic sample analysis called quadrupole magnetic steering control (QMSC). QMSC was used to study the magnetophoretic behavior of polystyrene microbeads decorated with iron oxide nanospheres-coated polystyrene microbeads (IONSs-PS) and iron oxide nanorods-coated polystyrene microbeads (IONRs-PS) under the influence of a quadrupole low field gradient. During a 4-s QMSC experiment, the IONSs-PS and IONRs-PS were navigated to perform 180° flip and 90° turn formations, and their kinematic results (2 s before and 2 s after the flip/turn) were measured and compared. The results showed that the IONRs-PS suffered from significant kinematic disproportion, translating a highly uneven amount of kinetic energy from the same magnitude of magnetic control. Combining the kinematic analysis, transmission electron microscopy micrographs, and vibrating sample magnetometry measurements, it was found that the IONRs-PS experienced higher fluid drag force and had lower consistency than the IONSs-PS due to its extensive open fractal nanorod structure on the bead surface and uneven magnetization, which was attributed to its ferrimagnetic nature.

Overlooked flocs in electrocoagulation-based ultrafiltration systems: A new understanding of the structural interfacial properties

An integrated ferrate-induced electrocoagulation-ultrafiltration (FECUF) process is proposed to cope with the growing demand for water treatment. Although flocs formed during the electrocoagulation (EC) process are useful for contaminant reduction and mitigation of membrane fouling, few studies have been focused on their structures and properties. Herein, we investigated the formation and structural transformations of flocs and their responses to organic matter, as well as the relationships between their interfacial properties and membrane fouling mitigation. It was found that ferrate contributed to the fast formation of flocs during the ferrate-induced electrocoagulation (FEC) process, which accelerated the FECUF process. Physicochemical analyses indicated that the flocs formed in the FEC process were mainly composed of Fe(III)-(hydr)oxides with abundant hydroxyl groups and poor crystallinity, which allowed complexation with NOM. Therefore, the mobilities of the NOM and the soluble coagulant ions were reduced. The responses of flocs to NOM suggested that the period of 0-20 min resulted in the most efficient NOM removal. In addition, two patterns revealed the relationships between the interfacial properties of the small colloidal particles (SCPs) and the membrane filtration performance: i) the decline in the initial flux was closely related to the composition (gel-type substances or metal-(hydr)oxides) of the SCPs and ii) the steady-state flux was influenced by the energy barrier between the SCPs. However, when the SCPs had the same composition, the interfacial properties influenced both the initial flux and the steady-state flux. This study provides an alternative FECUF process for intensive upgrades of centralized water treatment systems.

Monitoring effects of hydrodynamic cavitation pretreatment of sodium oleate on the aggregation of fine diaspore particles through small-angle laser scattering

Hydrodynamic cavitation (HC) enhanced fine particle aggregation could be largely due to the generation of tiny bubbles and their role in bridging particles. However, the lack of adequate characterizations of aggregates severally limits our further understanding of the associated aggregation behaviors. In this study, the aggregation of fine diaspore particles was comparatively investigated in sodium oleate (NaOl) solutions with and without HC pretreatment through the small-angle laser scattering (SALS) technique in a shear-induced aggregation (SIA) system. Results showed that HC pretreatment caused the formation of bulk nanobubbles (BNBs), which significantly modified the particle interactions and thereby modified the size and mass fractal dimension (Df) of aggregates under different SIA conditions. Although HC pretreatment did not noticeably alter the gradual change trend of aggregate size and structure characteristics under specific variables, BNBs bridging facilitated the aggregation process towards the diffusion-limited cluster aggregation model, resulting in the formation of larger but looser aggregates. This effect was more pronounced under relatively high NaOl concentrations. Apart from BNBs, the aggregation was also affected by cavitation bubbles formed during shear cavitation, which was more significant under high stirring intensity conditions (i.e., 1800 rpm) than the low stirring intensity conditions (i.e., 600 rpm).

Characterizing Flocculated Mineral Sediments with Acoustic Backscatter, Using Solid and Hybrid Scattering Models

This study investigated the performance of an acoustic backscatter system (ABS) for the in situ particle characterization of complex wastes. Two sediments were used: a fine, milled calcite that was flocculated with anionic polyacrylamide and naturally flocculated pond sludge. Particles were initially measured independently by light-based techniques to gain size, the coefficient of variation (COV), and fractal dimensions. For acoustic experiments, a bespoke, high-fidelity ABS was employed with 1, 2.25, and 5 MHz probes and a recirculating mixing tank. Initially, the concentration independent attenuation and backscatter coefficients were measured for each system using a robust calibration procedure at multiple concentrations. Comparisons of the total scattering cross-section (χ) and form function (f) were made between the experimental data and two semiempirical models: a Solid Scattering model and a Hybrid model (where the effects of bound fluid are incorporated). Experimental data compared more closely to the Solid Scattering model, as it was assumed scattering was dominated by small, bound "flocculi" rather than the macroscopic structure. However, if the COV was used as a fit parameter, the hybrid model could give equally accurate fits for a range of input aggregate sizes, highlighting that important size and structure information can be gained from the acoustic models if there is some a priori system data. Additionally, dual-frequency inversions were undertaken to measure concentration profiles for various frequency pairs. Here, the lowest frequency pair gave the best performance (with accurate measurements in the range of 2-35 g·L-1) as interparticle scattering was lowest.

Facile Photoresponsive Actuators Based on Ferrocene-Doped Poly(butyl methacrylate)

This paper presents facile photoresponsive actuators comprising ferrocene as a guest chromophore and poly(butyl methacrylate) (PBMA) as a host matrix. The ferrocene-doped PBMA film exhibits mechanical expansion and contraction when a 445 nm laser is turned on and off, respectively. The photoresponsive film is attached by a commercially available acetylcellulose adhesive tape, which exhibits a bending motion that is controlled by turning the laser on and off. Thereafter, the double-layer film is employed to fabricate a table-shaped lifting machine (0.7 mg) that lifts a 10.5 mg object up and down by turning the laser on and off, respectively, and the mechanical force offered by the double-layer film is recorded. Additionally, the film is coated with gold and applied to an electric circuit that serves as a reversible photoresponsive switch. This film preparation technique is applied to other chromophores (e.g., Coumarin 343, Rhodamine 6G, Sudan Blue II, and Solvent Green 3) to independently control the motions of the films with 445, 520, and 655 nm lasers. The ferrocene-containing films also exhibit photoinduced healing from mechanical damage. Finally, the photoirradiation-accompanied morphological changes in the film are observed via small-angle X-ray scattering.

Using small angle x-ray scattering to examine the aggregation mechanism in silica nanoparticle-based ambigels for improved optical clarity

Silica-based aerogels are a promising low-cost solution for improving the insulation efficiency of single-pane windows and reducing the energy consumption required for space heating and cooling. Two key material properties required are high porosity and small pore sizes, which lead to low thermal conductivity and high optical transparency, respectively. However, porosity and pore size are generally directly linked, where high porosity materials also have large pore sizes. This is unfavorable as large pores scatter light, resulting in reduced transmittance in the visible regime. In this work, we utilized preformed silica colloids to explore methods for reducing pore size while maintaining high porosity. The use of preformed colloids allows us to isolate the effect of solution conditions on porous gel network formation by eliminating simultaneous nanoparticle growth and aggregation found when using typical sol-gel molecular-based silica precursors. Specifically, we used in situ synchrotron-based small-angle x-ray scattering during gel formation to better understand how pH, concentration, and colloid size affect particle aggregation and pore structure. Ex situ characterization of dried gels demonstrates that peak pore widths can be reduced from 15 to 13 nm, accompanied by a narrowing of the overall pore size distribution, while maintaining porosities of 70%-80%. Optical transparency is found to increase with decreasing pore sizes while low thermal conductivities ranging from 95 +/- 13 mW/m K are maintained. Mechanical performance was found to depend primarily on effective density and did not show a significant dependence on solution conditions. Overall, our results provide insights into methods to preserve high porosity in nanoparticle-based aerogels while improving optical transparency.

Evaluation of properties and structural transitions of Poly (2-acrylamido-2-methyl-1-propanesulfonic acid-co-acrylonitrile) / β-Galactosidase complex coacervates: effects of pH and aging

The coacervates of the Poly (2-acrylamido-2-methyl-1-propanesulfonic acid-co-acrylonitrile) / β-Galactosidase complex are characterized using several techniques (Turbidimetry, dynamic and static light scattering (DLS / SLS), optical microscopy, image dynamic light scattering (IDLS), and ultra-small angles light scattering (USALS)). Turbidity and SLS were used to accurately determine the critical pHs of complex formation (pH_c, pH_ϕ1, pH_opt, and pH_ϕ2), DLS was used to probe the microscopic structure of coacervate droplets rich in proteins and polyelectrolytes in liquid-liquid phase separation, and IDLS and USALS have been introduced to better understand, during aging, the topology of the network formed of materials based on fractals in the dense phase. Observations of the architecture, the spatial inhomogeneity, and the size distributions of liquid complex coacervate droplets and fractal solid precipitates, were performed by optical microscopy. The pair-distance distribution function, P(r), presented in this review, is a new methodology of calculus for determining with precision the radius of gyration R_g of droplets coacervates. These techniques show that aging improves the stability of swollen condensates, the growth of the coacervate droplets is due to the attractive electrostatic interactions within the complex and does not undergo Ostwald ripening, except for the case of pH_opt and having fractal dimensions D_f generated by diffusion-limited cluster aggregation (DLCA).

Responsivity of Fractal Nanoparticle Assemblies to Multiple Stimuli: Structural Insights on the Modulation of the Optical Properties

Multi-responsive nanomaterials based on the self-limited assembly of plasmonic nanoparticles are of great interest due to their widespread employment in sensing applications. We present a thorough investigation of a hybrid nanomaterial based on the protein-mediated aggregation of gold nanoparticles at varying protein concentration, pH and temperature. By combining Small Angle X-ray Scattering with extinction spectroscopy, we are able to frame the morphological features of the formed fractal aggregates in a theoretical model based on patchy interactions. Based on this, we established the main factors that determine the assembly process and their strong correlation with the optical properties of the assemblies. Moreover, the calibration curves that we obtained for each parameter investigated based on the extinction spectra point out to the notable flexibility of this nanomaterial, enabling the selection of different working ranges with high sensitivity. Our study opens for the rational tuning of the morphology and the optical properties of plasmonic assemblies to design colorimetric sensors with improved performances.

Estimating the Shear Resistance of Flocculated Kaolin Aggregates: Effect of Flocculation Time, Flocculant Dose, and Water Quality

The resistance of kaolin aggregates to shearing in water clarification and recovery operations is a critical input in designing thickener feed wells. A recently formulated but already available criterion is used to determine the shear strength of flocculated kaolin aggregates. The flocculant is a high molecular weight anionic polyelectrolyte. The resistance of the aggregates is evaluated as a function of flocculation time, flocculant dosage, and water quality. The determination is based on a standardized experimental method. First, the time evolution of the average size of kaolin flocs is measured when aggregates are exposed to incremental shear rates from a predetermined base value. Then, the results are fitted to a pseudo-first-order model that allows deriving a characteristic value of the shear rate of rupture associated with the upper limit of the strength of the aggregates. In seawater, at a given dose of flocculant, the strength of the aggregates increases with time up to a maximum; however, at longer times, the resistance decreases until it settles at a stable value corresponding to stable aggregates in size and structure. A higher flocculant dosage leads to stronger aggregates due to more bridges between particles and polymers, leading to a more intricate and resistant particle network. In industrial water with very low salt content, the resistance of the kaolin aggregates is higher than in seawater for the same dose of flocculant. The salt weakens the resistance of the aggregates and works against the efficiency of the flocculant. The study should be of practical interest to concentration plants that use seawater in their operations.

Mesostructural study on graphenic-based carbon prepared from coconut shells by heat treatment and liquid exfoliation

In this study, the effect of heating temperature on the structure of graphenic-based carbon (GC) has been successfully investigated. A series of GC materials was prepared from coconut shells by a green synthesis method. The process includes heating at four temperatures (T = 400, 600, 800 and 1000 °C) followed by an exfoliation process assisted by hydrochloric acid (HCl). These materials were characterized by wide- and small-angle x-ray scattering (WAXS and SAXS), Fourier-transform infrared spectroscopy (FTIR), x-ray photoemission spectroscopy (XPS) and transmission electron microscopy (TEM). The WAXS analysis shows Braggs peaks corresponding to the reduced graphene oxide (rGO)-like phase. Investigations by FTIR and XPS methods show the presence of carbon-oxygen functional groups such as C=C (carbon with sp² hybridization), C–C (carbon with sp³ hybridization), and C=O bonds. The sp² bonds form a 2-dimensional (2D) network in hexagonal lattice, while carbon with sp³ bonds tends to form a 3-dimensional (3D) tetrahedral structure. The BET analysis revealed meso- and micro-pore structures in GC. Heating process reduces the specific surface area and increases pore size of GC. Moreover, increasing the heating temperature induces a decrease in radius of gyration (R_g) and an increase in the formation of 2D structures in GC. The fitting results of SAXS profiles, proved by TEM and XPS, yielded the structure of GC containing the mixture of 2D and 3D structures. Thus, it is suggested that the GC has a mesostructure.

Flocculation Efficiency and Spatial Distribution of Water in Oil Sands Tailings Flocculated with a Partially Hydrophobic Graft Copolymer

This work investigates the effect of partially hydrophobic grafted polymers on flocculation and dewatering of oil sands mature fine tailings. Here, we combine confocal microscopy and rheology to investigate how the graft density of ethylene-propylene-diene grafted with hydrolyzed poly(methyl acrylate) (EPDM-g-HPMA) affects its dispersion in water and flocculation efficiency in terms of sediment solids content and long-term dewatering of oil sands tailings. Increasing the graft density from 30 to 50% makes the flocculant easier to disperse, increases the rate of initial dewatering, and also enhances the viscoelastic response of the flocculated sediments. Conversely, the long-term rheological properties of the flocculated sediments were similar for all flocculants. Tri-dimensional microscopic details of the spatial distribution of water within the flocculated sludge provide novel insights into the performance of the flocculants. Increasing the graft density in EPDM-g-HPMA traps more water within the individual flocs and, consequently, decreases the post-flocculation dewatering rate. Our systematic approach confirms the importance of the spatial distribution of water in the flocculated sediment, which depends on how the flocculant is dispersed and how it retains water in the flocs.

Influence of temperature and salt on coacervation in an aqueous mixture of poly-L-lysine (PLL) and poly-(sodium styrene sulfonate) (PSSNa)

The mixture of poly-L-lysine (PLL) and long-chain PSSNa can lead to the formation of soluble complexes depending on pH, PLL concentration, ionic strength, and temperature. The influence of these stimuli was studied by zetametry, dynamic and ultra-small-angle light scattering, and turbidimetric measurements. First of all, we studied the stoichiometry of complexation, and then considered the influence of salt concentration and temperature on the behavior of the mixture at different pH values. These findings have allowed us to conclude that the polyelectrolyte-polypeptide stoichiometry is controlled by electrostatic interactions between opposite charges. At mass ratios between 1.8 and 2.3 and with net charges close to neutrality, unstable complexes were formed and flocculated due to the hydrophobic attraction leading to macroscopic phase separation. The linear charge density of the complex is also controlled by the ionic strength. Higher CaCl₂ concentrations reduce the complex stability and decrease the charge density, which leads to surface patch binding (SPB) at higher pH. Finally, the electrostatic interactions and strength of hydrogen bonds increased the stabilization of the complexes formed at temperatures lower than 45 °C. At temperatures higher than 45 °C, hydrophobic interactions became more dominant, causing a destabilization of the complexes.

Electrical impedance spectroscopy as a potential tool to investigate the structure and size of aggregates during water and wastewater treatment

Microscopic structure and size are important metrics for estimating aggregates environmental behaviors during water and wastewater treatment. However, in-situ determination of these characteristics is still a challenge. Here, we drew inspiration from a block disassembly process to propose an electrical impedance spectroscopy (EIS) method and constructed a generalized framework to associate macroscale electrical properties with microscopic structure and size-related characteristics of aggregates of different hierarchies. Extracted via EIS, the proposed models were verified to be capable of describing the self-similarity of aggregates and capturing the fractal and size information. Further, the proposed models exhibited a wide range of applications, which agrees well with the data gathered from various activated sludges, other colloids, and microgels in water and wastewater treatment. Finally, the EIS method was achieved online monitoring of fractal dimension and floc size during a sludge pre-oxidation conditioning process, which was elected as an example to illustrate the potential online applications of this EIS method in real water and wastewater environment. The obtained on-line data were used to indicate the potential suitable oxidation time during sludge pre-oxidation conditioning. These observations may inspire new methods of quantifying the aggregate structure and promote intelligent and dynamic decision-making during water and wastewater treatment.

Impacts of composite flocculant in coagulation/ultrafiltration hybrid process for treatment of humic acid water: the role of basicity

The effects of the composite flocculant, polyaluminium chloride and poly dimethyldiallylammonium chloride (PACl-PDMDAAC) in comparison with PACl on coagulation efficiencies and membrane fouling in coagulation-ultrafiltration (C-UF) process were analysed, which was conducted in the conditions of different basicity (B) values and the presence of Mg²⁺. Results showed that PACl-PDMDAAC enhanced the ability of charge neutralization and absorption bridging, and improved the coagulation efficiency. When B value was 1.5, the flocculant hydrolyzed to form more Al_b morphology and effectively removed HA molecules. The presence of Mg²⁺ could improve the coagulation performance through bridging ability. The results of the ultrafiltration test showed that the flux reduction for PACl was 70%, while the flux reduction for PACl-PDMDAAC was 60% in C-UF process. PACl-PDMDAAC could effectively reduce membrane fouling mainly by reducing strongly attached cake/gel layer. When B value was 1.5, the Al_b content of the flocculant was higher and the ability of adsorption charge neutralization was strong, resulting in forming a stable cake layer. Therefore, the membrane fouling was the lightest. In addition, the presence of Mg²⁺ in raw water reduced the membrane fouling.

Gelation of amphiphilic janus particles in an apolar medium

HYPOTHESIS

The anisotropic nature of colloidal particles results in orientation-dependent interactions that organize the particles into peculiar structures different from those formed by isotropic colloids. Particles with a hydrophilic hemisphere are expected to assemble in hydrophobic solvents due to the contribution of hydrophobic interactions as observed for molecular amphiphiles.

EXPERIMENTS

Asymmetrically decorated silica-based Janus particles are dispersed in an apolar solvent, chloroform, and their structure and dynamics are studied by light scattering and compared with computer simulations.

FINDINGS

Gelation of amphiphilic Janus particles with asymmetric surface decoration is observed in a hydrophobic medium. The influence of particle asymmetry on gel structure and dynamics is discussed. Unlike particles with long-range repulsive interactions in water, these systems rapidly form rather compact structures that are nevertheless more ramified than those made of isotropic hydrophobic particles. Comparison with computer simulations allows visualization of the gel and reveals a contribution of asymmetric short-range attractions and cross-term repulsions to the net effective interaction potential.

Understanding the coagulation mechanism and floc properties induced by Fe(VI) and FeCl3: population balance modeling

Coagulation kinetics and floc properties are of great fundamental and practical importance in the field of water treatment. To investigate the performance of Fe(VI) and Fe(III) salt on particle coagulation, Malvern Mastersizer 2000 was employed to continuously and simultaneously monitor the kaolin floc size and structure change, and population balance modeling was used to investigate the coagulation mechanism. The results show dosage increase had positive effect on collision efficiency and floc strength and negative effect on restructure rate. Low shear rate resulted in higher collision efficiency and stronger floc. Low water temperature had a pronounced detrimental effect on coagulation kinetics. Temperature increase showed the most significant positive effect on collision efficiency, floc strength and restructure rate. The optimum pH zone for the coagulation was found to be between 6 and 8. Further pH increase lowered the collision efficiency and floc strength and increased the restructure rate. FeCl₃ resulted in a larger ratio of the mass to volume of kaolin flocs (compactness) than those induced by ferrate.

Magnetic-Field Directed Vapor-Phase Assembly of Low Fractal Dimension Metal Nanostructures: Experiment and Theory

While gas-phase synthesis techniques offer a scalable approach to production of metal nanoparticles, directed assembly is challenging due to fast particle diffusion rates that lead to random Brownian aggregation. This work explores an electromagnetic-levitation technique to generate metal nanoparticle aggregates with fractal dimension (D_f) below that of diffusion limited assembly. We demonstrate that in addition to levitation and induction heating, the external magnetic field is sufficient to compete with random Brownian forces, which enables the formation of altered fractals. Ferromagnetic metals (Fe, Ni) form chain-like aggregates, while paramagnetic Cu forms compact nanoparticle aggregates with higher D_f values. We have also employed a Monte Carlo simulation to evaluate the necessary field strength to form linear chains in the gas phase.

Micro-nano particulate compositions of Hypericum perforatum L in ultra high diluted succussed solution medicinal products

The fact that many patients all over the world use homeopathic ultra high diluted succussed medicinal products, makes very interesting an explanation about the structure of them since until now only unconfirmed hypotheses are made. The present study focuses on the still unanswered questions about what happens with the chemical composition and the physicochemical properties of these products using Hypericum Perforatum L as a representative paradigm. All samples were prepared according to manufacturing procedures described mainly in S. Hahnemann's “Organon” and were examined by SEM, XRD, FTIR, DLS micro Mastersizer, DLS nano Zetasizer, UV-Vis and TEM. Measurements of electrical conductivity and pH were effectuated by the appropriate devices. During trituration of source material in alpha-lactose monohydrate some functional chemical groups present in source material disappeared and some others new ones came in view at the end of the process. A differentiation upon physicochemical properties between the source material and final triturating product was viewed, as well as micro-nanoparticles in colloidal form in all potencies derived trituration or extraction origin were present. The findings showed that the whole preparation process leads to the creation of micro nanoparticles something that for solid origin these products are created by trituration and for extract origin products these nanoparticles exist from the beginning.

Ionic strength and polyelectrolyte molecular weight effects on floc formation and growth in Taylor-Couette flows

Polyelectrolyte-driven flocculation of suspended particulate in solution is an important process in a variety of industrial processes such as drinking water treatment and composite material synthesis. Flocculation depends on a wide variety of physicochemical and hydrodynamic properties, which affect floc size, growth rate, and floc morphology. Floc formation and growth behavior is explored here using two different molecular weights of a cationic polyacrylamide flocculant and anisotropic Na-bentonite clay particles under a variety of solution ionic strengths. A Taylor-Couette cell with radial injection capabilities was used to study the effects of solution ionic strength and polyelectrolyte molecular weight on floc size, growth rate, and floc morphology during the flocculation process with a constant global velocity gradient. The floc size generally decreased with increasing ionic strength whereas the floc growth rate initially increased then decreased. This likely occurred due to charge screening effects, where increased bentonite aggregate size and a less expanded polyelectrolyte conformation at higher ionic strengths results in a decreased ability for the polyelectrolyte to bridge multiple bentonite aggregates. The densification of bentonite aggregates at higher ionic strengths resulted in floc morphologies that were more resistant to shear-induced breakage. With the exceptions of optimal dose concentration and dispersion coefficients, there were no clear differences in the floc growth rate behaviors for the two molecular weights studied. This work contributes to an improved understanding of the physicochemical complexities of polyelectrolyte-driven flocculation that can inform dosing requirements for more efficient industrial operations.

Enhanced Room-Temperature Photoluminescence Quantum Yield in Morphology Controlled J-Aggregates

Supramolecular assemblies from organic dyes forming J-aggregates are known to exhibit narrowband photoluminescence with full-width at half maximum of ≈9 nm (260 cm-1). Applications of these high color purity emitters, however, are hampered by the rather low photoluminescence quantum yields reported for cyanine J-aggregates, even when formed in solution. Here, it is demonstrated that cyanine J-aggregates can reach an order of magnitude higher photoluminescence quantum yield (increase from 5% to 60%) in blend solutions of water and alkylamines at room temperature. By means of time-resolved photoluminescence studies, an increase in the exciton lifetime as a result of the suppression of non-radiative processes is shown. Small-angle neutron scattering studies suggest a necessary condition for the formation of such highly emissive J-aggregates: the presence of a sharp water/amine interface for J-aggregate assembly and the coexistence of nanoscale-sized water and amine domains to restrict the J-aggregate size and solubilize monomers, respectively.

Ultrafiltration pre-oxidation by boron-doped diamond anode for algae-laden water treatment: membrane fouling mitigation, interface characteristics and cake layer organic release

In this study, ultrafiltration (UF) pre-oxidation with a boron-doped diamond (BDD) electrode was employed aiming to mitigate membrane fouling during algae-laden water treatment. It was found that BDD anodizing can efficiently alleviate membrane fouling regardless of the filtration membrane material when the oxidation time was over 30 min. This was because that the cake layer fouling resistance was highly mitigated by the pre-oxidation process. The generated small molecular organics after anodic oxidation might increase the potential of pore blockage. The anodizing preferentially oxidized hydrophobic organic and fluorescent substances, which is conducive to reducing membrane fouling and improving production efficiency. Besides, disinfection byproduct precursors and harmful algae derived substances of UF filtrated solution were contained. The algae bodies tend to agglomeration and the zeta potential obviously declined after the pretreatment, which is instrumental in forming a loose cake layer structure. In addition, the interaction force between membrane and foulants also converted to a repulsion force after pre-oxidation, which implies that BDD pre-oxidation was an effective way to mitigate cake layer fouling by reducing foulant-membrane interactions. At last, the secondary organic release of a dynamic formed cake layer was proved to be limited especially for living algae cells.

Effects of hydrodynamic shear stress on sludge properties, N2O generation, and microbial community structure during activated sludge process

Sludge properties are critical to the treatment performance and potentially correlate with nitrous oxide (N₂O) generation during activated sludge processes. The hydrodynamic shear stress induced by aeration has a significant influence on sludge properties and is inevitable for wastewater treatment plants (WWTPs). In this study, the effects of aerobic induced hydrodynamic shear stress on sludge properties, N₂O generation, and microbial community structure were investigated using three parallel sequencing batch reactors (SBRs) with identical dissolved oxygen (DO) concentrations. Results showed that with a shear stress increase from 1.5 × 10^-2 N/m² to 5.0 × 10^-2 N/m², the COD and NH₄⁺-N removal rates were enhanced from 89.4% to 94.0% and from 93.9% to 98.0%, respectively, while the TN removal rate decreased from 66.0% to 56.5%. Settleability of the activated sludge flocs (ASFs) also increased with the enhancement of shear stress, due to variation in sludge properties including particle size, regularity, compactibility, and EPS (extracellular polymeric substances) composition. The increase in shear stress promoted oxygen diffusion within the ASFs and mitigated NO₂^--N accumulation, leading to a decrease in the N₂O-N conversion rate from (4.8 ± 0.3)% to (2.2 ± 0.6)% (based on TN removal). Microbial analysis results showed that the functional bacteria involved in the biological nitrogen removal was closely related with shear stress. The increase in shear stress favored the enrichment of nitrite oxidizing bacteria (NOB) while suppressed the accumulation of ammonia-oxidizing bacteria (AOB) and denitrifying bacteria (DNB).

Nonintrusive investigation of large Al-kaolin fractal aggregates with slow settling velocities

Although a combination of aggregate characteristics dictate particle settling, it is commonly assumed that large particles have higher terminal velocities. This simplifying assumption often leads to overprediction of large aggregate settling velocities which in turn negatively impacts on estimates of sedimentation clarification efficiency. Despite its importance, little attention has been given to large aggregates with slow-settling velocities. This paper addresses this gap by investigating slow-settling velocities of large, heterodisperse and multi-shape Al-kaolin aggregates using non-intrusive methods. A particle image velocimetry technique (PIV) was applied to track aggregate velocity and a non-intrusive image technique was used to determine aggregate characteristics, including size (d_f), three-dimensional fractal dimension (D_f), density (ρ_f), aggregate velocity (V_exp) and Reynolds number (Re). Results showed no strict dependence of settling velocity on large aggregate size, shape and density, as Al-kaolin aggregates with the same size exhibited different settling velocities. A comparison of the results with the well-known Stokes' law for velocity modified by a shape factor showed that the settling velocities measured here can vary from 2 to 14 fold lower than the predicted values for perfect sphere-shape aggregates with the same density and size. Furthermore, results have also shown large Al-kaolin aggregate's drag coefficient (Cd) to be around 56/Re, for average fractal aggregate sphericity of around 0.58.

Connecting particle interactions to agglomerate morphology and rheology of boehmite nanocrystal suspensions

HYPOTHESIS

The rheology of complex suspensions, such as nuclear waste slurries at the Hanford and Savannah River sites, imposes significant challenges on industrial-scale processing. Investigating the rheology and connecting it to the agglomerate morphology and underlying particle interactions in slurries will provide important fundamental knowledge, as well as prescriptive data for practical applications. Here, we use suspensions of nano-scale aluminum oxyhydroxide minerals in the form of boehmite as an analog of the radioactive waste slurry to investigate the correlation between particle interactions, agglomerate morphology, and slurry rheology.

EXPERIMENTS

A combination of Couette rheometry and small-angle scattering techniques (independently and simultaneously) were used to understand how agglomerate structure of slurry changes under flow and how these structural changes manifest themselves in the bulk rheology of the suspensions.

FINDINGS

Our experiments show that the boehmite slurries are thixotropic, with the rheology and structure of the suspensions changing with increasing exposure to flow. In the slurries, particle agglomerates begin as loose, system-spanning clusters, but exposure to moderate shear rates causes the agglomerates to irreversibly consolidate into denser clusters of finite size. The structural changes directly influence the rheological properties of the slurries such as viscosity and viscoelasticity. Our study shows that solution pH affects the amount of structural rearrangement and the kinetics of the rearrangement process, with an increase in pH leading to faster and more dramatic changes in bulk rheology, which can be understood via correlations between particle interactions and the strength of particle network. Nearly identical structural changes were also observed in Poiseuille flow geometries, implying that the observed changes are relevant in pipe flow as well.

Effects of Extracellular Polymeric Substances on the Formation and Methylation of Mercury Sulfide Nanoparticles

Growing evidence has suggested that microbial biofilms are potential environmental "hotspots" for the production and accumulation of a bioaccumulative neurotoxin, methylmercury. Here, we demonstrate that extracellular polymeric substances (EPS), the main components of biofilm matrices, significantly interfere with mercury sulfide precipitation and lead to the formation of nanoparticulate metacinnabar available for microbial methylation, a natural process predominantly responsible for the environmental occurrence of methylmercury. EPS derived from mercury methylating bacteria, particularly Desulfovibrio desulfuricans ND132, substantially increase the methylation potential of nanoparticulate mercury. This is likely due to the abundant aromatic biomolecules in EPS that strongly interact with mercury sulfide via inner-sphere complexation and consequently enhance the short-range structural disorder while mitigating the aggregation of nanoparticulate mercury. The EPS-elevated bioavailability of nanoparticulate mercury to D. desulfuricans ND132 is not induced by dissolution of these nanoparticles in aqueous phase, and may be dictated by cell-nanoparticle interfacial reactions. Our discovery is the first step of mechanistically understanding methylmercury production in biofilms. These new mechanistic insights will help incorporate microbial EPS and particulate-phase mercury into mercury methylation models, and may facilitate the assessment of biogeochemical cycling of other nutrient or toxic elements driven by EPS-producing microorganisms that are prevalent in nature.

Sedimentation Kinetics of Magnetic Nanoparticle Clusters: Iron Oxide Nanospheres vs Nanorods

A detailed study of the sedimentation kinetics of iron oxide nanoparticle (IONP) clusters composed of nanospheres and nanorods is presented. Measurements were performed to determine the absorbance of an IONP suspension undergoing sedimentation over time by using a UV-vis spectrophotometer with simultaneous monitoring of the hydrodynamic diameter of the clusters formed with dynamic light scattering (DLS). Mathematical analysis based on Happel's spherical and cylindrical models was conducted to reveal the relationship between the settling velocity of the IONP clusters and their packing density. For the case of IONP clusters composed of rodlike particles, two distinctive phases of sedimentation were recorded, with the occurrence of rapid sedimentation at the beginning of the process (phase I) followed by a slower settling rate (phase II). In sedimentation phase II, even though the nanorod clusters had a hydrodynamic size of >500 nm, which was much larger than that of the nanosphere clusters (∼200 nm), their settling velocity of 0.0038 mm/min was still slower than that of the nanosphere clusters. Such observations were mainly a result of the packing density differences between the formed clusters; due to the end-to-end particle interactions of nanorods, the nanorod clusters were less tightly packed and more permeable. In addition to the mathematical analysis, quartz crystal microbalance with dissipation (QCM-D) was employed to measure the "softness" of the IONP clusters formed, and this physical property can be further related to their packing density. This study illustrated that for a rapidly aggregating system, such as magnetic IONPs, not only do the particle shape and size uniformity contribute to the physical properties of the particle clusters formed but also the nature of the aggregation, either end-to-end and/or side-to-side, should be carefully considered when designing a colloidally stable IONP suspension.

Hydrothermal SiO2 Nanopowders: Obtaining Them and Their Characteristics

The technological mode of obtaining amorphous SiO₂ nanopowders based on hydrothermal solutions is proposed in this study. Polycondensation of orthosilicic acid as well as ultrafiltration membrane separation, and cryochemical vacuum sublimation were used. The characteristics of nanopowders were determined by tunneling electron microscopy, low-temperature nitrogen adsorption, X-ray diffraction, and small-angle X-ray scattering. The scheme allows to adjust density, particle diameters of nanopowders, specific surface area, as well as diameters, area and volume of the pore. Thus, the structure of nanopowders is regulated—the volume fraction of the packing of spherical particles in aggregates and agglomerates, the size of agglomerates, and the number of particles in agglomerates. The pour densities of the nanopowders depend on the SiO₂ content in sols, which were 0.02 to 0.3 g/cm³. Nanoparticles specific surface area was brought to 500 m²/g by low temperature polycondensation. Nanoparticle aggregates specific pore volume (0.2–0.3 g/cm³) weakly depend on powders density. The volume fraction of the packing of SiO₂ nanoparticles in aggregates was 0.6–0.7. Solid samples of compacted nanopowders had a compressive strength of up to 337 MPa. Possible applications of hydrothermal SiO₂ nanopowders are considered.

Fit-for-purpose treatment of produced water with iron and polymeric coagulant for reuse in hydraulic fracturing: Temperature effects on aggregation and high-rate sedimentation

Reusing produced water for hydraulic fracturing simultaneously satisfies challenges of fresh water sourcing and the installation/operation of an extensive disposal well infrastructure. Herein, we systematically and rigorously investigate produced water treatment for reuse during hydraulic fracturing. Highly saline and turbid produced water from the Permian Basin was treated by adding chlorine as an oxidant, FeCl₃ as the primary coagulant, and an anionic polymer to induce high rate sedimentation to generate "clean brine" by removing suspended solids and iron over a range of environmentally relevant temperatures. Mobile phone video capture, optical microscopy, and digital image/video analysis were employed to characterize floc morphology and measure its size and settling velocity. Conformational changes of the polymeric coagulant between 4 and 44 °C were inferred from viscosity and dynamic light scattering measurements providing clues to its performance characteristics. Floc settling velocities measured over the entire range of polymer dosages and temperatures were empirically modelled incorporating their fractal nature, average size, and the viscosity of the produced water using only a single fitting parameter. Juxtaposing the anionic polymer with the hydrolyzing metal-ion coagulant effectively destabilized the suspension and caused floc growth through a combination of enmeshment, adsorption and charge neutralization and inter-particle bridging as evidenced by Fourier transform infrared spectroscopy and thermogravimetric analysis. Very high turbidity (≥98%) and total iron (≥97%) removals were accomplished even with very short flocculation and sedimentation times of only 6 minutes each suggesting the feasibility of this approach to reuse produced water for hydraulic fracturing.

A combined experimental and numerical approach to the assessment of floc settling velocity using fractal geometry

Sedimentation processes are fundamental to solids/liquid separation in water and wastewater treatment, and therefore a robust understanding of the settlement characteristics of mass fractal aggregates (flocs) formed in the flocculation stage is fundamental to optimized settlement tank design and operation. However, the use of settling as a technique to determine aggregates' traits is limited by current understanding of permeability. In this paper, we combine experimental and numerical approaches to assess settling velocities of fractal aggregates. Using a non-intrusive in situ digital image-based method, three- and two-dimensional fractal dimensions were calculated for kaolin-based flocs. By considering shape and fractal dimension, the porosity, density and settling velocities of the flocs were calculated individually, and settling velocities compared with those of spheres of the same density using Stokes' law. Shape analysis shows that the settling velocities for fractal aggregates may be greater or less than those for perfect spheres. For example, fractal aggregates with floc fractal dimension, D_f = 2.61, floc size, d_f > 320 μm and d_p = 7.5 μm settle with lower velocities than those predicted by Stokes' law; whilst, for D_f = 2.33, all aggregates of d_f > 70 μm and d_p = 7.5 μm settled below the velocity calculated by Stokes' law for spheres. Conversely, fractal settling velocities were higher than spheres for all the range of sizes, when D_f of 2.83 was simulated. The ratio of fractal aggregate to sphere settling velocity (the former being obtained from fractal porosity and density considerations), varied from 0.16 to 4.11 for aggregates in the range of 10 and 1,000 μm, primary particle size of 7.5 μm and a three-dimensional fractal dimension between 2.33 and 2.83. However, the ratio decreases to the range of 0.04-2.92 when primary particle size changes to 1.0 μm for the same fractal dimensions. Using the floc analysis technique developed here, the results demonstrate the difference in settlement behaviour between the approach developed here and the traditional Stokes' law approach using solid spheres. The technique and results demonstrate the improvements in understanding, and hence value to be derived, from an analysis based on fractal, rather than Euclidean, geometry when considering flocculation and subsequent clarification performance.

Kinetically assembled binary nanoparticle networks

Embedding percolating networks of nanoparticles (NPs) within polymers is a promising approach for mechanically reinforcing polymers and for introducing novel electronic, transport, and catalytic properties into otherwise inert polymers. While such networks may be obtained through kinetic assembly of unary system of NPs, the ensuing structures exhibit limited morphologies. Here, we investigate the possibility of increasing the diversity of NP networks through kinetic assembly of multiple species of NPs. Using lattice Monte Carlo simulations we show that networks obtained from co-assembly of two NP species of different sizes exhibit significantly more diverse morphology than those assembled from a single species. In particular, we achieved considerable variations in the particle spatial distribution, proportions of intra- and interspecies contacts, fractal dimension, and pore sizes of the networks by simply modulating the stoichiometry of the two species and their intra and inter-species affinities. We classified these distinct morphologies into "integrated", "coated", "leaved", and "blocked" phases, and provide relevant phase diagrams for achieving them. Our findings are relevant to controlled and predictable assembly of particle networks for creating multifunctional composites with improved properties.

Digestate management for high-solid anaerobic digestion of organic wastes: A review

Digestate management for anaerobic digestion (AD) is becoming a bottleneck of the sustainability of AD plants when the use of digestate for agricultural application is restricted due to nutrient surplus and low market acceptance. Digestate quality and treatment in high solid anaerobic digestion (HSAD) can be better than conventional low-solid system. The rheological behavior of digestate in high solid anaerobic digestion (HSAD) can have a great impact on the energy consumption of digestate management. After post-conditioning guided by rheological parameters, the solid digestate can be further treated based on the integrated solutions to enhance the energy efficiency or nutrients recovery. The environmental impacts for some core parts of those integrated systems were also evaluated in this study. This article presented a critical review of recent investigations of digestate management for HSAD, especially focusing on the rheology of HSAD digestate, integrated solutions and their environmental performances.

Effect of shear rate on floc characteristics and concentration factors for the harvesting of Chlorella vulgaris using coagulation-flocculation-sedimentation

Coagulation-based separation has been increasingly applied to microalgal harvesting because of its competitive cost and high scalability. The characteristics of flocs formed during coagulation/flocculation are critical for efficient harvesting. However, few studies have been devoted to systematically investigating the structural characteristics of microalgal flocs and their influences on subsequent settling performance. In this paper, the dynamic mean size and fractal dimension, strength, regrowth and settling performance of Al³⁺ coagulated Chlorella vulgaris flocs were characterized at various flocculation shear rates. The influence of shear rate on floc characteristics was revealed. An appropriate shear rate (9 s^-1) produced more desirable microalgal flocs (in terms of size and compactness), with better settling performance and a higher concentration factor, than higher or lower shear rates, favoring their separation and subsequent harvesting. At this condition, the concentration factor reached 13.50, which was a 177.21% improvement over the 4.87 reached at a low shear rate.