Development of an automated on-line solid-phase extraction-high-performance liquid chromatographic method for the analysis of aniline, phenol, caffeine and various selected substituted aniline and phenol compounds in aqueous matrices

Comparison of gas chromatographic techniques for the analysis of iodinated derivatives of aromatic amines

Some aromatic amines (AA) have been classified as carcinogens to humans. After entering the body, mainly through tobacco smoke, they can be detected in urine. Thus, their trace analysis as biomarkers in biofluids is of high relevance and can be achieved with gas chromatography (GC-MS), usually after derivatization. This study compares three gas chromatographic methods for the analysis of ten iodinated derivatives of AA: GC-MS in single-ion monitoring (SIM) mode with (1) electron ionization (GC-EI-MS) and (2) negative chemical ionization (GC-NCI-MS), and (3) GC-EI-MS/MS in multiple reaction monitoring (MRM) mode using electron ionization. All methods and most analytes showed good coefficients of determination (R² > 0.99) for broad linear ranges covering three to five orders of magnitude in the picogram-per-liter to nanogram-per-liter range, with one and two exceptions for (1) and (2) respectively. Excellent limits of detection (LODs) of 9-50, 3.0-7.3, and 0.9-3.9 pg/L were observed for (1), (2), and (3) respectively, and good precision was achieved (intra-day repeatability < 15% and inter-day repeatability < 20% for most techniques and concentration levels). On average, recoveries between 80 and 104% were observed for all techniques. Urine samples of smokers and non-smokers were successfully analyzed, and p-toluidine and 2-chloroaniline could be found at significantly (α = 0.05) higher concentrations among smokers.

Fluorescence Quenching of Carbazole by Selected Phenols in a Cationic Micellar System of Cetyltrimethyl Ammonium Bromide (CTAB)

A group of selected phenols i.e., picric acid, p-Nitrophenol, m-Nitrophenol, o-Nitrophenol, and phenol interactions were studied with a fluorescent probe carbazole in a micellar system of CTAB. CTAB concentration was optimized for maximum quenching of carbazole for each studied phenol. Interaction was studied in 0.02 and 0.1 mol/dm³ CTAB. All the studied phenols resulted in the quenching of carbazole in both CTAB concentrations though lower CTAB concentration was found optimum for highest quenching of the probe carbazole. Carbazole fluorescence quenching with phenols were explained with the help of Stern-Volmer equation that produced the constants of Stern-Volmer ([Formula: see text]). [Formula: see text] shows the sensitiveness of the method for the studied phenol and were observed in the order picric acid > phenol > m-Nitrophenol > p-Nitrophenol > o-Nitrophenol. Detection threshold (DT) and quantification threshold (QT) were observed in the order 1.76 [Formula: see text] 10^-7 - 6.30 [Formula: see text] 10^-7 mol/dm³ and 5.898 [Formula: see text] 10^-7 - 2.11 [Formula: see text] 10^-6 mol/dm³ respectively. The method is reproducible and is effective for the determination of studied phenols in the samples.

Effect of storage states on stability of three organophosphorus insecticide residues on cowpea samples

BACKGROUND

The stability of pesticide residues in stored samples is very important to ensure the quality of data about the residues. The evaluation of pesticide residues in food and environment samples is an important means to ensure food quality and protect consumers against potential dietary risks. Improper storage of pesticide residue samples may result in loss of pesticide and unreliable data, which could affect safety assessments.

RESULTS

The influences of storage conditions, including temperature (-20 °C, 4 °C, and ambient temperature) and sample state (homogenized state and coarsely chopped state) on the storage stability of dichlorvos, malathion, and diazinon on cowpea were studied. Dichlorvos and malathion were more stable in an homogenized state than in a coarsely chopped state. At 4 °C, the residual dichlorvos in the coarsely chopped state and the homogenized state, respectively, was 12% and 69%; the residual malathion was 26% and 92%, respectively. Dichlorvos suffered a large loss of 89% and 59% for coarsely chopped and homogenized cowpea, even at -20 °C. It was obvious that the stability of dichlorvos and malathion were more affected by storage state than diazinon. The stability of diazinon was significantly affected by temperature. The effect of storage state and temperature on stability is likely to be correlated with enzymes in the matrix, such as superoxide dismutase (SOD), catalase (CAT), and peroxidase (POD).

CONCLUSION

The optimal stable storage conditions for three organophosphorus insecticides residues on cowpea were in the homogenized state and under a lower temperature. © 2021 Society of Chemical Industry.

Surfactant-functionalised magnetic ferum oxide coupled with high performance liquid chromatography for the extraction of phenol

The usage of phenols in the marketplace has been increasing tremendously, which has raised concerns about their toxicity and potential effect as emerging pollutants. Phenol's structure has closely bonded phenyl and hydroxy groups, thereby making its functional characteristics closely similar to that of alcohol. As a result, phenol is used as a base compound for commercial home-based products. Hence, a simple and efficient procedure is required to determine the low concentration of phenols in environmental water samples. In this research, a method of combining magnetic nanoparticles (MNPs) with surfactant Sylgard 309 was developed to overcome the drawbacks in the classical extraction methods. In addition, this developed method improved the performance of extraction when MNPs and the surfactant Sylgard 309 were used separately, as reported in the previous research. This MNP-Sylgard 309 was synthesised by the coprecipitation method and attracts phenolic compounds in environmental water samples. Response surface methodology was used to study the parameters and responses in order to obtain an optimised condition using MNP-Sylgard 309. The parameters included the effect of pH, extraction time, and concentration of the analyte. Meanwhile, the responses measured were the peak area of the chromatogram and the percentage recovery. From this study, the results of the optimum conditions for extraction using MNP-Sylgard 309 were pH 7, extraction time of 20 min, and analyte concentration of 10.0 μg mL^-1. Under the optimized conditions, MNP-Sylgard 309 showed a low limit of detection of 0.665 μg mL^-1 and the limit of quantification was about 2.219 μg mL^-1. MNP-Sylgard 309 was successfully applied on environmental water samples such as lake and river water. High recovery (76.23%-110.23%) was obtained.

Dispersive liquid-liquid microextraction based on a new hydrophobic deep eutectic solvent for the determination of phenolic compounds in environmental water samples

Dispersive liquid-liquid microextraction has garnered increasing attention in sample preparation due to its rapid and efficient extraction process. In this study, a new terpineol-based hydrophobic deep eutectic solvent was firstly synthesized by mixing α-terpineol with 1-octanoic acid, and then applied to analysis of phenols from water samples by dispersive liquid-liquid microextraction combined with high-performance liquid chromatography and diode array detection. Infrared spectroscopy indicated that hydrogen bonding was responsible for the formation of deep eutectic solvent between α-terpineol and 1-octanoic acid. After optimization of several parameters, such as the type and volume of deep eutectic solvent and the disperser, pH and ionic strength of sample solution, the developed method exhibited excellent extraction performance to the phenols with the enrichment factors from 27 to 32. Good linearity was acquired ranging from 5 to 5000 μg/L, and detection of limits of the proposed method for the phenols ranged from 0.15 to 0.38 μg/L. The recoveries measured by spiked samples at three concentration levels ranged from 81.6 to 99.3%, and precision was found with intra- and inter-day relative standard deviations less than 8.7 and 9.2%, respectively. Finally, the proposed method was successfully applied to the determination of the phenols in environmental water samples.

Optimization of a solid-phase microextraction technique for chloro‑ and nitro- substituted aromatic compounds using design of experiments

A rapid and sensitive direct immersion solid-phase microextraction (SPME) technique for the analysis of seven chloro (Cl-) and nitro (NO₂-) substituted anilines, toluenes, and nitrobenzenes from small volume (1.5 mL) aqueous samples was optimized for gas chromatography using Design of Experiments (DoE). Screening of the SPME factors was performed by a fractional factorial DoE, and the optimization of influential factors was achieved with a central composite multi-response surface DoE. Extraction time, pre-SPME agitation speed, extraction temperature, and desorption temperature were identified as significant factors and their values were set using a desirability function that maximized the extraction of the seven target analytes. Extraction time and agitation speed showed significant interactions for most analytes (α = 0.05). The relative standard deviations (RSDs) for within-day and between-day analyses were below 8%, suggesting that the method was repeatable and reproducible. The obtained limits of detection were in the low μg/L range (1-10) using a Flame Ionization Detector, far below what is needed for industrial contaminated sites (usually >1 mg/L). The optimized SPME method increased the analyte concentration up to 2-3 orders of magnitude compared with direct GC injection. The optimized SPME method was applied to two groundwater samples from a contaminated site in which the concentrations of three of the target analytes were ranged from 0.06 to 9.42 mg/L with RSDs <11%. When the concentrations of the target analytes in the sample matrix were higher than 0.5 mg/L, a competition for the SPME extraction sites was observed where analytes with higher affinity for the fiber material replaced the analytes with lower affinity. As a result, dilution of highly contaminated samples is recommended. This study provided for the first time an analytical method for the quantification of frequently co-occurring contaminants from the chloro‑ and nitro- substituted aniline, toluene, and nitrobenzene families.

Synthesis of a molecularly imprinted polymer and its application in selective extraction of fenoprofen from wastewater

The presence of various classes of pharmaceutical drugs in different environmental compartments has been reported worldwide. In South Africa, the detection of pharmaceuticals especially the non-steroidal anti-inflammatory drugs is recent, and more studies are being done in order to fully understand their fate in the aquatic environment. With considerations for the need of better sample preparation techniques, this study synthesized a molecularly imprinted polymer for the selective extraction of a non-steroidal anti-inflammatory drug, fenoprofen in aqueous environmental samples. Batch adsorption studies showed that adsorption of fenoprofen onto the cavities of the polymer followed a Langmuir isotherm as well as a pseudo second order model implying formation of a monolayer on the surface through chemisorption. The polymer had a maximum adsorption capacity of 38.8 mg g^-1 and a Langmuir surface area of 1607 m² g^-1. The imprinted polymer was then used as the selective sorbent for solid phase extraction in the analysis of fenoprofen from wastewater followed by chromatographic determination. The analytical method gave a detection limit of 0.64 ng mL^-1 and recovery of 99.6%. The concentration of fenoprofen detected in influent and effluent samples from two wastewater treatment plants ranged from 24 to 58 ng mL^-1. The ability of the treatment plants to remove fenoprofen during wastewater processing based on the difference in concentrations in influent and effluent samples was found to be 41%. This work has shown that there is a possibility of release of fenoprofen from wastewater treatment plants into surface water sources.

Supramolecular nanosolvent-based hollow fiber liquid phase microextraction as a novel method for simultaneous preconcentration of acidic, basic and amphiprotic pollutants

In this study, for the first time, coextraction of acidic, basic and amphiprotic pollutants was performed using supramolecular nano solvent-based hollow fiber liquid phase microextraction.

Preparation and use of maize tassels' activated carbon for the adsorption of phenolic compounds in environmental waste water samples

The determination and remediation of three phenolic compounds bisphenol A (BPA), ortho-nitrophenol (o-NTP), parachlorophenol (PCP) in wastewater is reported. The analysis of these molecules in wastewater was done using gas chromatography (GC) × GC time-of-flight mass spectrometry while activated carbon derived from maize tassel was used as an adsorbent. During the experimental procedures, the effect of various parameters such as initial concentration, pH of sample solution, eluent volume, and sample volume on the removal efficiency with respect to the three phenolic compounds was studied. The results showed that maize tassel produced activated carbon (MTAC) cartridge packed solid-phase extraction (SPE) system was able to remove the phenolic compounds effectively (90.84-98.49%, 80.75-97.11%, and 78.27-97.08% for BPA, o-NTP, and PCP, respectively). The MTAC cartridge packed SPE sorbent performance was compared to commercially produced C18 SPE cartridges and found to be comparable. All the parameters investigated were found to have a notable influence on the adsorption efficiency of the phenolic compounds from wastewaters at different magnitudes.

Hollow fiber liquid-phase microextraction with in situ derivatization combined with gas chromatography-mass spectrometry for the determination of root exudate phenylamine compounds in hot pepper ( Capsicum annuum L.)

Hollow fiber liquid-phase microextraction (HF-LPME) with derivatization was developed for the determination of three root exudate phenylamine compounds in hot pepper ( Capsicum annuum L.) by gas chromatography-mass spectrometry (GC-MS). The performance and applicability of the proposed procedure were evaluated through the extraction of 1-naphthylamine (1-NA), diphenylamine (DPA), and N-phenyl-2- naphthaleneamine (N-P-2-NA) in a recirculating hydroponic solution of hot pepper. Parameters affecting the extraction efficiency were investigated. The calibration curves showed a good linearity in the range of 0.1-10 μg mL(-1). The limits of detection (S/N = 3) for the three compounds were 0.096, 0.074, and 0.057 μg mL(-1), respectively. The enrichment factors reached 174, 196, and 230 at the concentration of 5 μg mL(-1), and relative standard deviations (RSD) of 9.5, 8.6, and 7.8% and 8.4, 7.6, and 6.2% were obtained at concentrations of 2 and 5 μg mL(-1) for 1-NA, DPA, and N-P-2-NA, respectively. Recoveries ranging from 90.2 to 96.1% and RSDs below 9.1% were obtained when HF-LPME with in situ derivatization was applied to determine root exudate 1-NA, DPA, and N-P-2-NA after 15 and 30 days of culture solution, respectively.

Simultaneous determination of five nitroaniline and dinitroaniline isomers in wastewaters by solid-phase extraction and high-performance liquid chromatography with ultraviolet detection

A high-performance liquid chromatography (HPLC)-ultraviolet detection method, combined with solid-phase extraction (SPE), was developed for the determination of five nitroaniline and dinitroaniline isomers including 2-nitroaniline, 3-nitroaniline, 4-nitroaniline, 2,4-dinitroaniline and 2,6-dinitroaniline in wastewater samples. Extraction of the five isomers was carried out with a hydrophile-lipophile balance cartridge, the Oasis HLB. The cartridge was washed by a mixed aqueous solution containing 10% (v/v) acetonitrile and 10% (v/v) ethyl acetate before the five isomers were eluted by a mixture of methanol and acetic acid. Separation of the five isomers was achieved by using an Agilent TC-C(18) column at 30°C, and using a mixture of acetonitrile/water 30/70 (v/v) as mobile phase under an isocratic condition at a flow rate of 1.0 mL/min. The analytes were detected by a UV detector at a wavelength of 225 nm. Recoveries of the five isomers in the spiked sewage sample were between 84.6% and 94.0% with a relative standard deviation of less than 4.7%. The limits of quantification (LOQ) determined in a spiked sewage sample of 500 mL were 2.0 x 10(-9)M for 2-nitroaniline, 3-nitroaniline and 2,6-dinitroaniline, and 4.5 x 10(-9)M for 4-nitroaniline and 2,4-dinitroaniline. The proposed method was applied to determine the five isomers in real samples of acidic wastewater and printing and dyeing wastewater.

Occurrence and fate of pharmaceuticals in wastewater treatment plants and rivers in Korea

We measured 25 pharmaceuticals in ten municipal wastewater treatment plants (WWTPs), one hospital WWTP and five rivers in Korea. In the municipal WWTP influents, acetaminophen, acetylsalicylic acid and caffeine showed relatively high concentrations. The occurrence of pharmaceuticals in the wastewater seems to be influenced by production and consumption of pharmaceuticals. The hospital WWTP influent showed higher total concentrations of pharmaceuticals than the municipal WWTPs, and caffeine, ciprofloxacin and acetaminophen were dominant. In the rivers, caffeine was dominant, and the distribution of pharmaceuticals was related to the inflow of the wastewater. In the municipal WWTPs, the concentrations of acetaminophen, caffeine, acetylsalicylic acid, ibuprofen and gemfibrozil decreased by over 99%. The decrease of these pharmaceuticals occurred mainly during the biological processes. In the physico-chemical processes, the decrease of pharmaceuticals was insignificant except for some cases. In the hospital WWTP, ciprofloxacin, acetylsalicylic acid, acetaminophen and carbamazepine showed the decrease rates of over 80%.

Methodologies for the extraction of phenolic compounds from environmental samples: new approaches

Phenolic derivatives are among the most important contaminants present in the environment. These compounds are used in several industrial processes to manufacture chemicals such as pesticides, explosives, drugs and dyes. They also are used in the bleaching process of paper manufacturing. Apart from these sources, phenolic compounds have substantial applications in agriculture as herbicides, insecticides and fungicides. However, phenolic compounds are not only generated by human activity, but they are also formed naturally, e.g., during the decomposition of leaves or wood. As a result of these applications, they are found in soils and sediments and this often leads to wastewater and ground water contamination. Owing to their high toxicity and persistence in the environment, both, the US Environmental Protection Agency (EPA) and the European Union have included some of them in their lists of priority pollutants. Current standard methods of phenolic compounds analysis in water samples are based on liquid–liquid extraction (LLE) while Soxhlet extraction is the most used technique for isolating phenols from solid matrices. However, these techniques require extensive cleanup procedures that are time-intensive and involve expensive and hazardous organic solvents, which are undesirable for health and disposal reasons. In the last years, the use of news methodologies such as solid-phase extraction (SPE) and solid-phase microextraction (SPME) have increased for the extraction of phenolic compounds from liquid samples. In the case of solid samples, microwave assisted extraction (MAE) is demonstrated to be an efficient technique for the extraction of these compounds. In this work we review the developed methods in the extraction and determination of phenolic derivatives in different types of environmental matrices such as water, sediments and soils. Moreover, we present the new approach in the use of micellar media coupled with SPME process for the extraction of phenolic compounds. The advantages of micellar media over conventional extractants are reduction of organic solvent, low cost, easy handling and shorter time procedures.

Spatial and temporal distribution of pesticide residues in surface waters in northeastern Greece

A monitoring study of 147 compounds in surface river waters from northeastern Greece near Greek/Bulgarian/Turkish borders was carried out during 1999-2007. Based on agricultural use eight sampling points along the rivers Ardas, Evros and Erythropotamos were set up, covering the distance from the Greek/Bulgarian borders down to the river's discharge (river's delta) in the Greek territory. In total, 88 sampling events were carried out from 1999 to 2007. Pesticides were extracted by solid-phase extraction (SPE) and analyzed by gas chromatography-mass spectrometry (GC-EI-MS) using a multiresidue in-house analytical method including pesticides belonging to different chemical classes. Aquatic risk concerning the detected pesticides was assessed on the basis of the risk quotient (RQ = PEC/PNEC). From the 28 compounds (pesticides, metabolites and caffeine) that were detected in surface waters of northeastern Greece the soil applied pesticides were the most frequently detected. High pesticide concentrations were detected within 2 months of their application. Extreme pesticide concentrations were detected in the beginning of the irrigation season or just after high rainfall events. Generally, low levels of pesticide residues were found in the first sampling point (Greek/Bulgarian borders) of all rivers, however o',p' DDT, o',p' DDE and gamma-HCH were mainly detected in this sampling point regarded as cross-boundary contamination. The most commonly encountered compounds in the river waters were atrazine, DEA, alachlor, trifluralin, prometryne, molinate, carbofuran, carbaryl and diazinon. Increased loading (primary as well as secondary peaks) seemed to be a consequence of application (timing, rate, frequency) and intense rainfall during the application period. Aquatic risk assessment revealed that from the 28 compounds that were constantly detected 12 showed non-acceptable risk when median concentrations were used as PEC and 18 when extreme concentrations were used as PEC values.