Peptide functionalized poly(l-lysine)-g-poly(ethylene glycol) on titanium: resistance to protein adsorption in full heparinized human blood plasma

Multiprotein Adsorption from Human Serum at Gold and Oxidized Iron Surfaces Studied by Atomic Force Microscopy and Polarization-Modulation Infrared Reflection Absorption Spectroscopy

Multiprotein adsorption from complex body fluids represents a highly important and complicated phenomenon in medicine. In this work, multiprotein adsorption from diluted human serum at gold and oxidized iron surfaces is investigated at different serum concentrations and pH values. Adsorption-induced changes in surface topography and the total amount of adsorbed proteins are quantified by atomic force microscopy (AFM) and polarization-modulation infrared reflection absorption spectroscopy (PM-IRRAS), respectively. For both surfaces, stronger protein adsorption is observed at pH 6 compared to pH 7 and pH 8. PM-IRRAS furthermore provides some qualitative insights into the pH-dependent alterations in the composition of the adsorbed multiprotein films. Changes in the amide II/amide I band area ratio and in particular side-chain IR absorption suggest that the increased adsorption at pH 6 is accompanied by a change in protein film composition. Presumably, this is mostly driven by the adsorption of human serum albumin, which at pH 6 adsorbs more readily and thereby replaces other proteins with lower surface affinities in the resulting multiprotein film.

Self-assembly strategy to reduce non-specific adsorption for the development of high sensitivity quantitative immunoassay

The development of functionalized surfaces with low non-specific adsorption is important for their biomedical applications. To inhibit non-specific adsorption on glass substrate, we designed a novel optical biochip by modifying a layer of dense negatively charged film (SO₃^2-) on its substrate surface via self-assembly. Compared with the untreated glass substrate, it reduced the adsorption by about 300-fold or 400-fold by poly (styrene sulfonic acid) sodium salt (PSS), or meso-tetra (4-sulfonatophenyl) porphine dihydrochloride (TSPP) on individually the modified glass substrate. Considering the effect of fluorescence resonance energy transfer (FRET) between TSPP and the QDs in solution by mixing, a strategy of 2-layer of TSPP followed by 4-layer of PSS was designed to modify the glass for preparing biochips. Under the optimized conditions, the biochip on functionalized glass substrate co-treated with TSPP and PSS realized the sensitive quantitative detection of C-reactive protein (CRP) based on a quantum dot fluorescence immunosorbent assay (QD-FLISA). The limit of detection (LOD) for CRP achieved 0.69 ng/mL with the range of 1-1,000 ng/mL using TSPP and PSS co-treated glass substrate surface, which was respectively about 1.9-fold and 7.5-fold more sensitive to the PSS-modified biochip and the TSPP-modified biochip. This work demonstrated an effective and convenient strategy to obtain biochips with low non-specific adsorption properties on functionalized surfaces, thus providing a new approach for creating ultra-high sensitivity microchannels or microarrays on glass substrates.

Synthesis of nanomedicine hydrogel microcapsules by droplet microfluidic process and their pH and temperature dependent release

Chitosan and alginate hydrogels are attractive because they are highly biocompatible and suitable for developing nanomedicine microcapsules. Here we fabricated a polydimethylsiloxane-based droplet microfluidic reactor to synthesize nanomedicine hydrogel microcapsules using Au@CoFeB-Rg3 as a nanomedicine model and a mixture of sodium alginate and PEG-g-chitosan crosslinked by genipin as a hydrogel model. The release kinetics of nanomedicines from the hydrogel were evaluated by simulating the pH and temperature of the digestive tract during drug transport and those of the target pathological cell microenvironment. Their pH and temperature-dependent release kinetics were studied by measuring the mass loss of small pieces of thin films formed by the nanomedicine-encapsulating hydrogels in buffers of pH 1.2, 7.4, and 5.5, which replicate the pH of the stomach, gut and blood, and cancer microenvironment, respectively, at 20 °C and 37 °C, corresponding to the storage temperature of hydrogels before use and normal body temperature. Interestingly, nanomedicine-encapsulating hydrogels can undergo rapid decomposition at pH 5.5 and are relatively stable at pH 7.4 at 37 °C, which are desirable qualities for drug delivery, controlled release, and residue elimination after achieving target effects. These results indicate that the designed nanomedicine hydrogel microcapsule system is suitable for oral administration.

Locomotion of micromotors in paper chips

Locomotion of nano/micromotors in non-aqueous environments remains a challenging task. We assembled magnetic micromotors with different surface coatings and explored their locomotion in paper chips. Poly(L-lysine) deposition resulted in positively charged micromotors. Immobilized cellulase was used to increase the micromotors' paper penetration depth while a polyethylene glycol (PEG) coating was employed to limit the interaction between the micromotors and the cellulose fibers. All micromotors were able to move in the top layers of the paper chips with velocities dependent on the magnetic forces used to induce their locomotion, their sizes and the types of employed paper chips. Maximum speeds of up to ∼25 μm s^-1 were observed for PEGylated micromotors in the fibrous cellulose environment. This type of micromotors has the potential to be considered in the area of paper microfluidics to facilitate distribution, or collection of moieties for biosensing or cell culture.

Click-Coupling to Electrostatically Grafted Polymers Greatly Improves the Stability of a Continuous Monitoring Sensor with Single-Molecule Resolution

Sensing technologies for the real-time monitoring of biomolecules will allow studies of dynamic changes in biological systems and the development of control strategies based on measured responses. Here, we describe a molecular architecture and coupling process that allow continuous measurements of low-concentration biomolecules over long durations in a sensing technology with single-molecule resolution. The sensor is based on measuring temporal changes of the motion of particles upon binding and unbinding of analyte molecules. The biofunctionalization involves covalent coupling by click chemistry to PLL-g-PEG bottlebrush polymers. The polymer is grafted to a surface by multivalent electrostatic interactions, while the poly(ethylene glycol) suppresses nonspecific binding of biomolecules. With this biofunctionalization strategy, we demonstrate the continuous monitoring of single-stranded DNA and a medically relevant small-molecule analyte (creatinine), in sandwich and competitive assays, in buffer and in filtered blood plasma, with picomolar, nanomolar, and micromolar analyte concentrations, and with continuous sensor operation over 10 h.

Biomimetic Asymmetric Polymer Brush Coatings Bearing Fencelike Conformation Exhibit Superior Protection and Antifouling Performance

Antifouling surfaces with optimized conformation and compositional heterogeneities are presented with the goal of improving the efficacy of surface protection. The approach exploits the adhesive group (thiol or catechol chain end) to anchor asymmetric polymer brushes (APBs) bearing amphiphilic side chains with synergistic nonfouling and fouling-release abilities onto the surface. The conformation of the APB surface is close to the fencelike structure, which mimics lubricating protein lubricin, endowing the surface with capacity of enhanced protection and antiadhesivity, even facing the high compression of fouling. By utilizing a poly(Br-acrylate-alkyne) macroagent comprising alkynyl and 2-bromopropionate groups, we prepared a series of APB surfaces based on polyacrylate-g-poly(ethylene oxide)/poly(pentafluorophenyl methacrylate) (PA-g-PEO/PPFMA) APBs to explore the influence of the content of the fluorinated segment and bioinspired topological polymer chemistry on their antifouling performance. The APB surfaces can not only provide compositional heterogeneities of PEO and fluorinated segments in each side chain but also give a high surface coverage because of the characteristic of high grafting density of macromolecular brushes. It was found for the first time, as far as we are aware, the fencelike APB surface shows excellent antifouling performance with less protein adsorption (up to 91% off) and cell adhesion (up to 84% off) in comparison with the controlled substrate under relatively long incubation time.

Biodegradable Polymers as a Noncoding miRNA Nanocarrier for Multiple Targeting Therapy of Human Hepatocellular Carcinoma

Therapeutic strategy based on the restoration of tumor suppressor-microRNAs (miRNAs) is a promising approach for cancer therapy, but the low delivery efficiency of miRNA remains a huge hurdle due to the lack of safe and efficient nonviral carriers. In this work, with the use of newly developed PEGylated biodegradable charged polyester-based vectors (PEG-BCPVs) as the carrier, the miR26a and miR122 codelivering therapeutic strategy (PEG-BCPVs/miR26a/miR122 as the delivery formulation) is successfully developed for efficient treatment of human hepatocellular carcinoma (HCC). In vitro study results show that PEG-BCPVs are capable of effectively facilitating miRNA cellular uptake via a cell endocytosis pathway. Consequently, the restoration of miR26a and miR122 remarkably inhibit the cell growth, migration, invasion, colony formation, and induced apoptosis of HepG2 cells. More importantly, the chemosensitivity of HepG2 to anticancer drug is also considerably enhanced. After treatment with the PEG-BCPV-based miRNA delivery system, the expression of the multiple targeted genes corresponding to miR26a and miR122 in HepG2 cells is greatly downregulated. Accordingly, the newly developed miRNA restoration therapeutic strategy via biodegradable PEG-BCPVs as the carrier should be a promising modality for combating HCC.

Zwitterionic Polydopamine-Coated Manganese Oxide Nanoparticles with Ultrahigh Longitudinal Relaxivity for Tumor-Targeted MR Imaging

We present the design of antifouling zwitterion-functionalized manganese oxide (Mn₃O₄) nanoparticles (NPs) modified with folic acid (FA) for targeted tumor magnetic resonance (MR) imaging. In the current work, diethylene glycol-stabilized Mn₃O₄ NPs were initially prepared via a solvothermal approach, coated with polydopamine (PDA), fluorescently labeled with rhodamine B, conjugated with FA via amide bond formation, and finally covered with zwitterions of l-lysine (Lys). The thus-generated multifunctional Mn₃O₄ NPs display excellent water dispersibility and colloidal stability, good protein resistance ability, and desirable cytocompatibility. With the PDA and Lys modifications, the multifunctional Mn₃O₄ NPs own an ultrahigh r₁ relaxivity (89.30 mM^-1 s^-1) and enable targeted tumor MR imaging, owing to the linked FA ligands. The designed antifouling zwitterion-functionalized Mn₃O₄ NPs may be employed as an excellent MR contrast agent for targeted MR imaging of other biological systems.

Engineering the Surface Properties of a Zwitterionic Polymer Brush to Enable the Simple Fabrication of Inkjet-Printed Point-of-Care Immunoassays

Motivated by the lack of adventitious protein adsorption on zwitterionic polymer brushes that promise low noise and hence high analytical sensitivity for surface-based immunoassays, we explored their use as a substrate for immunoassay fabrication by the inkjet printing of antibodies. We observed that a poly(sulfobetaine)methacrylate brush on glass is far too hydrophilic to enable the noncovalent immobilization of antibodies by inkjet printing. To circumvent this limitation, we developed a series of hybrid zwitterionic-cationic surface coatings with tunable surface wettability that are suitable for the inkjet printing of antibodies but also have low protein adsorption. We show that in a microarray format in which both the capture and detection antibodies are discretely printed as spots on these hybrid brushes, a point-of-care sandwich immunoassay can be carried out with an analytical sensitivity and dynamic range that is similar to or better than those of the same assay fabricated on a PEG-like brush. We also show that the hybrid polymer brushes do not bind anti-PEG antibodies that are ubiquitous in human blood, which can be a problem with immunoassays fabricated on PEG-like coatings.

Integrin targeting of glyphosate and its cell adhesion modulation effects on osteoblastic MC3T3-E1 cells revealed by label-free optical biosensing

This study is a discovery of interesting and far reaching properties of the world leading herbicide active ingredient glyphosate. Here we demonstrate the cell adhesion-modifying characteristics of glyphosate affecting cellular interactions via Arg-Gly-Asp (RGD)-dependent integrins. This conclusion was supported by the observations that a glyphosate surface coating induced integrin-specific cell adhesion, while glyphosate in solution inhibited cell adhesion on an RGD-displaying surface. A sensitive, real-time, label-free, whole cell approach was used to monitor the cell adhesion kinetic processes with excellent data quality. The half maximal inhibitory concentration (IC50) for glyphosate was determined to be 0.47 ± 0.07% (20.6 mM) in serum-free conditions. A three-dimensional dissociation constant of 0.352 mM was calculated for the binding between RGD-specific integrins in intact MC3T3-E1 cells and soluble glyphosate by measuring its competition for RGD-motifs binding, while the affinity of those RGD-specific integrins to the RGD-motifs was 5.97 µM. The integrin-targeted affinity of glyphosate was proven using competitive binding assays to recombinant receptor αvβ3. The present study shows not only ligand-binding properties of glyphosate, but also illustrates its remarkable biomimetic power in the case of cell adhesion.

Resisting Bacteria and Attracting Cells: Spontaneous Formation of a Bifunctional Peptide-Based Coating by On-Surface Assembly Approach

Due to extension of life expectancy, millions of people suffer nowadays from bone and dental malfunctions that can only be treated by different types of implants. However, these implants tend to fail due to bacterial infection and lack of integration with the remaining tissue. Here, we demonstrate a new concept in which we use specifically designed peptides, in a "Lego-like" manner to endow multiple preprogrammed functions. We developed a bifunctional peptide-based coating that simultaneously rejects the adhesion of infecting bacteria and attracts cells that build the new connecting tissue. The peptide design contains fluorinated phenylalanine that mediates the self-assembly of the peptide into a coating that resists bacterial adhesion. It also includes an Arg-Gly-Asp (RGD) motif that attracts mammalian cells. The whole compound is attached to the surface using a third unit, the amino acid 3,4-dihydroxyphenylalanine (DOPA). This novel, yet very simple approach is significantly advantageous for practical use and synthesis. More importantly, this peptide design can serve as a general platform for generating functional coatings.

Bacterial Inhibition and Osteoblast Adhesion on Ti Alloy Surfaces Modified by Poly(PEGMA- r-Phosmer) Coating

We have synthesized and immobilized PEGMA₅₀₀-Phosmer to Ti6Al4V surfaces by a simple procedure to reduce bacteria-associated infection without degrading the cell response. Adhered bacteria coverage was lessened to 1% on polymer-coated surfaces when exposed to Escherichia coli, Staphylococcus epidermidis, and Streptococcus mutans. Moreover, PEGMA₅₀₀-Phosmer and homoPhosmer coatings presented better responses to MC3T3-E1 preosteoblast cells when compared with the results for PEGMA₂₀₀₀-Phosmer-coated and raw Ti alloy surfaces. The behavior of balancing bacterial inhibition and cell attraction of the PEGMA₅₀₀-Phosmer coating was explained by the grafted phosphate groups, with an appropriate PEG brush length facilitating greater levels of calcium deposition and further fibronectin adsorption when compared with that of the raw Ti alloy surface.

Impact of Bioactive Peptide Motifs on Molecular Structure, Charging, and Nonfouling Properties of Poly(ethylene oxide) Brushes

Polymer layers capable of suppressing protein adsorption from biological media while presenting extracellular matrix-derived peptide motifs offer valuable new options for biomimetic surface engineering. Herein, we provide detailed insights into physicochemical changes induced in a nonfouling poly(ethylene oxide) (PEO) brush/polydopamine (PDA) system by incorporation of adhesion ligand (RGD) peptides. Brushes with high surface chain densities (σ ≥ 0.5 chains·nm^-2) and pronounced hydrophilicity (water contact angles ≤ 10°) were prepared by end-tethering of heterobifunctional PEOs ( M_n ≈ 20 000 g·mol^-1) to PDA-modified surfaces from a reactive melt. Using alkyne distal end group on the PEO chains, azidopentanoic-bearing peptides were coupled through a copper-catalyzed Huisgen azide-alkyne "click" cycloaddition reaction. The surface concentration of RGD was tuned from complete saturation of the PEO surface with peptides (1.7 × 10⁵ fmol·cm^-2) to values which may induce distinct differences in cell adhesion (<6.0 × 10² fmol·cm^-2). Infrared reflection-absorption and X-ray photoelectron spectroscopies proved the PDA-PEO layers covalent structure and the immobilization of RGD peptides. The complete reconstruction of experimental electrohydrodynamics data utilizing mean-field theory predictions further verified the attained brush structure of the end-tethered PEO chains which provided hydrodynamic screening of the PDA anchor. Increasing the surface concentration of immobilized RGD peptides led to increased interfacial charging. Supported by simulations, this observation was attributed to the ionization of functional groups in the amino acid sequence and to the pH-dependent adsorption of water ions (OH^- > H₃O⁺) from the electrolyte. Despite the distinct differences observed in the electrokinetic analysis of the surfaces bearing different amounts of RGD, it was found that the peptide presence on PEO(20 000)-PDA layers does not have a significant effect on the nonfouling properties of the system. Notably, the presented PEO(20 000)-PDA layers bearing RGD peptides in the surface concentration range 5.9 to 1.7 × 10⁵ fmol·cm^-2 reduced the protein adsorption from fetal bovine serum to less than 30 ng·cm^-2, that is, values comparable to the ones obtained for pristine PEO(20 000)-PDA layers.

Bundle Gel Fibers with a Tunable Microenvironment for in Vitro Neuron Cell Guiding

As scaffolds for neuron cell guiding in vitro, gel fibers with a bundle structure, comprising multiple microfibrils, were fabricated using a microfluidic device system by casting a phase-separating polymer blend solution comprising hydroxypropyl cellulose (HPC) and sodium alginate (Na-Alg). The topology and stiffness of the obtained bundle gel fibers depended on their microstructure derived by the polymer blend ratio of HPC and Na-Alg. High concentrations of Na-Alg led to the formation of small microfibrils in a one-bundle gel fiber and stiff characteristics. These bundle gel fibers permitted for the elongation of the neuron cells along their axon orientation with the long axis of fibers. In addition, human-induced pluripotent-stem-cell-derived dopaminergic neuron progenitor cells were differentiated into neuronal cells on the bundle gels. The bundle gel fibers demonstrated an enormous potential as cell culture scaffold materials with an optimal microenvironment for guiding neuron cells.

Antitumor activity of a folate receptor-targeted immunoglobulin G-doxorubicin conjugate

Development of antibody-drug conjugates (ADCs) is a promising therapeutic strategy for cancer therapy. In this study, folate was conjugated via a polyethyleneglycol (PEG) linker to immunoglobulin G (IgG), which was linked to doxorubicin (DOX), to form a novel ADC folate-PEG-IgG-DOX (FA-PEG-IgG-DOX). The FA-PEG-IgG-DOX showed high targeting efficiency in HeLa and KB cells and significantly improved the uptake and retention of DOX compared with IgG-DOX about 10-fold. Subsequently, FA-PEG-IgG-DOX was shown to have at least 8 times higher antitumor activity than IgG-DOX both in HeLa and KB cells and also induced more apoptosis in those cells than IgG-DOX. Moreover, FA-PEG-IgG-DOX had a 2 times longer circulating time than FA-IgG-DOX, but did not increase the DOX distribution in mouse hearts. Importantly, FA-PEG-IgG-DOX treatment significantly inhibited tumor growth in xenograft mice. Together, our results indicate that FA-PEG-IgG is an effective ADC carrier for delivery of chemotherapeutic agents and that conjugating tumor targeting ligands to antibodies is a promising strategy for producing ADC drugs.

Rapid Assay to Assess Bacterial Adhesion on Textiles

Textiles are frequently colonized by microorganisms leading to undesired consequences like hygienic problems. Biocidal coatings often raise environmental and health concerns, thus sustainable, biocide-free coatings are of interest. To develop novel anti-adhesive textile coatings, a rapid, reliable, and quantitative high-throughput method to study microbial attachment to fabrics is required, however currently not available. Here, a fast and reliable 96-well plate-based screening method is developed. The quantification of bacterial adhesion is based on nucleic acid staining by SYTO9, with Pseudomonas aeruginosa and Staphylococcus aureus as the model microorganisms. Subsequently, 38 commercially available and novel coatings were evaluated for their anti-bacterial adhesion properties. A poly(l-lysine)-g-poly(ethylene glycol) coating on polyester textile substratum revealed an 80% reduction of bacterial adhesion. Both the coating itself and the anti-adhesive property were stable after 20 washing cycles, confirmed by X-ray analysis. The assay provides an efficient tool to rapidly screen for non-biocidal coatings reducing bacterial attachment.

Effect of grafted PEG chain conformation on albumin and lysozyme adsorption: A combined study using QCM-D and DPI

In this study, elucidation of protein adsorption mechanism is performed using dual polarization interferometry (DPI) and quartz crystal microbalance with dissipation (QCM-D) to study adsorption behaviors of bovine serum albumin (BSA) and lysozyme (LYZ) on poly (ethylene glycol) (PEG) layers. From the analysis of DPI, PEG2000 and PEG5000 show tight and loose mushroom conformations, respectively. Small amount of LYZ could displace the interfacial water surrounding the tight mushroomed PEG2000 chains by hydrogen bond attraction, leading to protein adsorption. The loose mushroomed PEG5000 chains exhibit a more flexible conformation and high elastic repulsion energy that could prevent protein adsorption of all BSA and most of LYZ. From the analysis of QCM, PEG2000 and PEG5000 show tight and extended brush conformations. The LYZ adsorbed mass has critical regions of PEG2000 (0.19 chain/nm(2)) and PEG5000 (0.16 chain/nm(2)) graft density. When graft density of PEG is higher than the critical region (brush conformations), the attraction of hydrogen bonds between PEG and LYZ is the dominant factor. When graft density of PEG is lower than the critical region (mushroom conformations), elastic repulsion between PEG and proteins is driven by the high conformation entropy of PEG chains, which is the dominant force of steric repulsion in PEG-protein systems. Therefore, the adsorption of BSA is suppressed by the high elastic repulsion energy of PEG chains, whereas the adsorption of LYZ is balanced by the interactions between the repulsion of entropy elasticity and the attraction of hydrogen bonds.

Non-proteinaceous bacterial adhesins challenge the antifouling properties of polymer brush coatings

Polymer brushes of poly(ethylene glycol) have long been considered the gold standard for antifouling surfaces that resist adsorption of biomolecules and attachment of microorganisms. However, despite displaying excellent resistance to protein adsorption, the polymer brush coatings cannot entirely avoid colonization by bacteria. Here we investigate and identify which non-proteinaceous bacterial adhesins challenge the antifouling properties of polymer brush coatings and how these challenges might be overcome. We quantified biofilm formation on a well-known polymer brush coating of poly(l-lysine)-graft-poly(ethylene glycol) (PLL-g-PEG) on titanium. The coating successfully resisted colonization by Staphylococcus aureus and Pseudomonas aeruginosa, but not Staphylococcus epidermidis. This colonization pattern was also reflected on the adhesion forces measured on single bacterial cells. The biofilm produced from S. epidermidis on PLL-g-PEG were found to be rich in polysaccharides and extracellular DNA, and quantification of DNA, polysaccharides and proteins on PLL-g-PEG surfaces revealed that although the coating almost fully resisted protein adsorption, polysaccharides could adsorb, and exposure to DNA led to desorption of the polymer from the titanium surface. We hypothesized that this problem could be overcome by increasing the polymer brush density to better resist the penetration of DNA and polysaccharides into the polymer layer. Indeed, high density PLL-g-PEG brushes prepared by the recently discovered temperature-induced polyelectrolyte (TIP) grafting method resisted the interaction with DNA and polysaccharides, and therefore also the colonization by S. epidermidis. The TIP grafting is a simple improvement of PLL-g-PEG brush formation, and our results suggest that it provides an important advancement to the bacterial resistance by polymer brush coatings.

STATEMENT OF SIGNIFICANCE

The antifouling properties of poly(ethylene glycol) brush coatings against protein adsorption are well documented, but it is not well understood why these coatings do not perform as well against bacterial colonization when tested against a wide range of species and over periods of days. Here we investigated bacterial colonization on poly(l-lysine)-graft-poly(ethylene glycol) (PLL-g-PEG) grafted on Ti, and revealed that bacteria relying mostly on polysaccharides and extracellular DNA for adhesion and biofilm formation could successfully colonize PLL-g-PEG coated surfaces. The coatings could not resist adsorption of polysaccharides, and DNA could even desorb the coatings from the Ti surface. Fortunately, the shortcomings of conventional PLL-g-PEG could be overcome by increasing the graft density, using the recently discovered and very simple grafting method, 'temperature-induced polyelectrolyte (TIP) grafting'. Our study highlights that it is of utmost importance to develop coatings which resist adsoprtion of non-proteinaceous bacterial adhesins such as polysaccharides and DNA, and we demonstrated that TIP grafted high density PLL-g-PEG coatings are promising materials to achieve diverse bacterial resistance.

Biocompatible long-sustained release oil-core polyelectrolyte nanocarriers: From controlling physical state and stability to biological impact

It has been generally expected that the most applicable drug delivery system (DDS) should be biodegradable, biocompatible and with incidental adverse effects. Among many micellar aggregates and their mediated polymeric systems, polyelectrolyte oil-core nanocarriers have been found to successfully encapsulate hydrophobic drugs in order to target cells and avoid drug degradation and toxicity as well as to improve drug efficacy, its stability, and better intracellular penetration. This paper reviews recent developments in the formation of polyelectrolyte oil-core nanocarriers by subsequent multilayer adsorption at micellar structures, their imaging, physical state and stability, drug encapsulation and applications, in vitro release profiles and in vitro biological evaluation (cellular uptake and internalization, biocompatibility). We summarize the recent results concerning polyelectrolyte/surfactant interactions at interfaces, fundamental to understand the mechanisms of formation of stable polyelectrolyte layered structures on liquid cores. The fabrication of emulsion droplets stabilized by synergetic surfactant/polyelectrolyte complexes, properties, and potential applications of each type of polyelectrolyte oil-core nanocarriers, including stealth nanocapsules with pegylated shell, are discussed and evaluated.

Incorporation of extra amino acids in peptide recognition probe to improve specificity and selectivity of an electrochemical peptide-based sensor

We investigated the effect of incorporating extra amino acids (AA) at the n-terminus of the thiolated and methylene blue-modified peptide probe on both specificity and selectivity of an electrochemical peptide-based (E-PB) HIV sensor. The addition of a flexible (SG)3 hexapeptide is, in particular, useful in improving sensor selectivity, whereas the addition of a highly hydrophilic (EK)3 hexapeptide has shown to be effective in enhancing sensor specificity. Overall, both E-PB sensors fabricated using peptide probes with the added AA (SG-EAA and EK-EAA) showed better specificity and selectivity, especially when compared to the sensor fabricated using a peptide probe without the extra AA (EAA). For example, the selectivity factor recorded in the 50% saliva was ∼2.5 for the EAA sensor, whereas the selectivity factor was 7.8 for both the SG-EAA and EK-EAA sensors. Other sensor properties such as the limit of detection and dynamic range were minimally affected by the addition of the six AA sequence. The limit of detection was 0.5 nM for the EAA sensor and 1 nM for both SG-EAA and EK-EAA sensors. The saturation target concentration was ∼200 nM for all three sensors. Unlike previously reported E-PB HIV sensors, the peptide probe functions as both the recognition element and antifouling passivating agent; this modification eliminates the need to include an additional antifouling diluent, which simplifies the sensor design and fabrication protocol.

Comparison of Mannose, Ethylene Glycol, and Methoxy-Terminated Diluents on Specificity and Selectivity of Electrochemical Peptide-Based Sensors

We report the synthesis and application of three new antifouling diluents for the fabrication of an E-PB HIV sensor. Among the three thiolated antifouling diluents used in this study, the methoxy-terminated diluent (C6-MEG) is the most effective in alleviating both nonspecific binding and adsorption of matrix contaminants onto the sensor surface, especially when compared to the mannose- (C6-MAN) and ethylene-glycol-terminated (C6-EG) diluents. The sensor fabricated with C6-MEG has a specificity factor (∼13.5) substantially higher than the sensor passivated with only 6-mercapto-1-hexanol (∼1.5). It is functional even when employed directly in 25% serum, an achievement that has not been observed with this class of E-PB sensors. More importantly, incorporation of these antifouling diluents has negligible impact on other important sensor properties such as sensitivity and binding kinetics. This sensor passivation strategy is versatile and can potentially be used with other E-PB sensors, as well as surface-based sensors that utilize thiol-gold self-assembled monolayer chemistry.

Self-assembled anchor layers/polysaccharide coatings on titanium surfaces: a study of functionalization and stability

Composite materials based on a titanium support and a thin, alginate hydrogel could be used in bone tissue engineering as a scaffold material that provides biologically active molecules. The main objective of this contribution is to characterize the activation and the functionalization of titanium surfaces by the covalent immobilization of anchoring layers of self-assembled bisphosphonate neridronate monolayers and polymer films of 3-aminopropyltriethoxysilane and biomimetic poly(dopamine). These were further used to bind a bio-functional alginate coating. The success of the titanium surface activation, anchoring layer formation and alginate immobilization, as well as the stability upon immersion under physiological-like conditions, are demonstrated by different surface sensitive techniques such as spectroscopic ellipsometry, infrared reflection-absorption spectroscopy and X-ray photoelectron spectroscopy. The changes in morphology and the established continuity of the layers are examined by scanning electron microscopy, surface profilometry and atomic force microscopy. The changes in hydrophilicity after each modification step are further examined by contact angle goniometry.

A survey of state-of-the-art surface chemistries to minimize fouling from human and animal biofluids

Fouling of artificial surfaces by biofluids is a plague Biotechnology deeply suffers from. Herein, we inventory the state-of-the-art surface chemistries developed to minimize this effect from both human and animal biosamples.

Polymeric nanoarchitectures on Ti-based implants for antibacterial applications

Because of the excellent mechanical properties and good biocompatibility, titanium-based metals are widely used in hard tissue repair, especially load-bearing orthopedic applications. However, bacterial infection and complication during and after surgery often causes failure of the metallic implants. To endow titanium-based implants with antibacterial properties, surface modification is one of the effective strategies. Possessing the unique organic structure composed of molecular and functional groups resembling those of natural organisms, functionalized polymeric nanoarchitectures enhance not only the antibacterial performance but also other biological functions that are difficult to accomplish on many conventional bioinert metallic implants. In this review, recent advance in functionalized polymeric nanoarchitectures and the associated antimicrobial mechanisms are reviewed.

Crack prevention of biodegradable polymer coating on metal facilitated by a nano-coupled interlayer

Crack prevention of biodegradable polymer coatings on drug-eluting stents was investigated by introducing a nano-coupled layer at the interface between the metal surface and the polymer coating layer using surface-initiated ring-opening polymerization of ε-caprolactone. Poly(d,l-lactide-co-glycolide) coating on cobalt-chromium control and ricinoleic acid-poly(caprolactone)–grafted cobalt-chromium was carried out using electrospraying. The cracking of the biodegradable polymer coating on drug-eluting stents during ballooning was addressed by introducing a nano-coupled interlayer on the cobalt-chromium surface. The ricinoleic acid-poly(caprolactone) nano-coupled interlayer and poly(d,l-lactide-co-glycolide)-coated top layer were characterized using attenuated total reflection Fourier transform infrared, contact angle, ellipsometry, X-ray photoelectron spectroscopy, and atomic force microscopy. Based on scratch tests, the nano-coupled samples had stronger interfacial adhesion compared to the control sample without the nano-coupled layer. Scanning electron microscope images indicated that the cracking on the poly(d,l-lactide-co-glycolide) coating was addressed. Introducing a nano-coupling interlayer may be an important strategy to preventing polymer coating cracking on drug-eluting stents.

Dependence of cancer cell adhesion kinetics on integrin ligand surface density measured by a high-throughput label-free resonant waveguide grating biosensor

A novel high-throughput label-free resonant waveguide grating (RWG) imager biosensor, the Epic® BenchTop (BT), was utilized to determine the dependence of cell spreading kinetics on the average surface density (v_RGD) of integrin ligand RGD-motifs. v_RGD was tuned over four orders of magnitude by co-adsorbing the biologically inactive PLL-g-PEG and the RGD-functionalized PLL-g-PEG-RGD synthetic copolymers from their mixed solutions onto the sensor surface. Using highly adherent human cervical tumor (HeLa) cells as a model system, cell adhesion kinetic data of unprecedented quality were obtained. Spreading kinetics were fitted with the logistic equation to obtain the spreading rate constant (r) and the maximum biosensor response (Δλ_max), which is assumed to be directly proportional to the maximum spread contact area (A_max). r was found to be independent of the surface density of integrin ligands. In contrast, Δλ_max increased with increasing RGD surface density until saturation at high densities. Interpreting the latter behavior with a simple kinetic mass action model, a 2D dissociation constant of 1753 ± 243 μm⁻² (corresponding to a 3D dissociation constant of ~30 μM) was obtained for the binding between RGD-specific integrins embedded in the cell membrane and PLL-g-PEG-RGD. All of these results were obtained completely noninvasively without using any labels.

PEG-g-chitosan thermosensitive hydrogel for implant drug delivery: cytotoxicity, in vivo degradation and drug release

Thermosensitive hydrogels based on chitosan are of great interests for injectable implant drug delivery. The poly(ethylene glycol)-grafted-chitosan (PEG-g-CS) hydrogel was reported as a potential thermosensitive system. The objective of the present study is to evaluate the cytotoxicity, in vivo degradation and drug release of PEG-g-CS hydrogel. Cytotoxicity was evaluated using L929 murine fibrosarcoma cell line. Degradation and drug release in vivo were investigated by subcutaneous injection of the hydrogel into Sprague-Dawley rats. PEG-g-CS polymer exhibits no significant cytotoxicity when its concentration is less than 3 mg mL(-1). After being implanted, PEG-g-CS hydrogel maintains its integrity for two weeks and collapses, merging into the tissue, in the third week. It causes moderate inflammatory response but no fibrous encapsulation around the hydrogel is found. The hydrogel presents a three-week sustained release of cyclosporine A with no significant burst release in vitro and produces the effective drug concentration in blood for more than five weeks in vivo, performing almost the same bioavailability to chitosan/glycerophosphate hydrogel. Further modifications of PEG-g-CS hydrogel might be necessary to modulate the degradation and to mitigate the fluctuations in blood drug concentration.

Direct grafting of anti-fouling polyglycerol layers to steel and other technically relevant materials

Direct grafting of hyperbranched polyglycerol (PG) layers onto the oxide surfaces of steel, aluminum, and silicon has been achieved through surface-initiated polymerization of 2-hydroxymethyloxirane (glycidol). Optimization of the deposition conditions led to a protocol that employed N-methyl-2-pyrrolidone (NMP) as the solvent and temperatures of 100 and 140 °C, depending on the substrate material. In all cases, a linear growth of the PG layers could be attained, which allows for control of film thickness by altering the reaction time. At layer thicknesses >5 nm, the PG layers completely suppressed the adhesion of albumin, fibrinogen, and globulin. These layers were also at least 90% bio-repulsive for two bacteria strains, E. coli and Acinetobacter baylyi, with further improvement being observed when the PG film thickness was increased to 17 nm (up to 99.9% bio-repulsivity on silicon).

Tuning thermoresponsive behavior of diblock copolymers and their gold core hybrids. Part 2. How properties change depending on block attachment to gold nanoparticles

Thermoresponsive diblock copolymers of di(ethylene glycol) methyl ether methacrylate (DEGMA) and oligo(ethylene glycol) methyl ether acrylate (OEGA) were synthesized by reversible addition-fragmentation chain transfer polymerization, allowing us to prepare diblocks with a thiol group at the desired chain end, and bond that block to a ~20 nm gold nanoparticle core. The cloud point and coil-globule transition window were measured by UV-vis spectroscopy. The gold core lowered the cloud point and narrowed the coil-globule transition window of all the diblock hybrids, but raised the cloud point of statistical copolymer hybrids that had similar cloud points. The extent of the change in the thermo-response properties of the hybrid diblock copolymers was more significant when the gold was bonded to the DEGMA block than the OEGA block. This block is less hydrophilic and sterically hindered than OEGA and may adsorb more effectively to the gold so that the hydration of the outer OEGA block is relatively unaffected by the Au core. This work indicates that diblock copolymers allow factors such as steric bulk and the effects on arrangement around a metal core to be effective tools for manipulating thermo-responsive properties that are not as significant with statistical copolymers.

George-Hyslop P, Dobson CM, Klenerman D. Single molecule characterization of the interactions between amyloid-β peptides and the membranes of hippocampal cells

Oligomers of the 40 and 42 residue amyloid-β peptides (Aβ40 and Aβ42) have been implicated in the neuronal damage and impaired cognitive function associated with Alzheimer's disease. However, little is known about the specific mechanisms by which these misfolded species induce such detrimental effects on cells. In this work, we use single-molecule imaging techniques to examine the initial interactions between Aβ monomers and oligomers and the membranes of live cells. This highly sensitive method enables the visualization of individual Aβ species on the cell surface and characterization of their oligomerization state, all at biologically relevant, nanomolar concentrations. The results indicate that oligomers preferentially interact with cell membranes, relative to monomers and that the oligomers become immobilized on the cell surface. Additionally, we observe that the interaction of Aβ species with the cell membrane is inhibited by the presence of ATP-independent molecular chaperones. This study demonstrates the power of this methodology for characterizing the interactions between protein aggregates and the membranes of live neuronal cells at physiologically relevant concentrations and opens the door to quantitative studies of the cellular responses to potentially pathogenic oligomers.

Biocompatibility studies of poly(ethylene glycol)–modified titanium for cardiovascular devices

The rapid protein adsorption on a material surface causes blood coagulation, platelet activation, and complement system activation, which poses a risk for failure of cardiovascular devices. In this study, a chemically hydroxylated titanium surface was aminosilanized and covalently grafted with poly(ethylene glycol). The reaction conditions on the grafted quantity were studied by the respective amine and carboxyl densities. The blood compatibility of the PEGylated surfaces with different poly(ethylene glycol) densities and chain lengths was evaluated; the PEGylated surfaces with higher grafted density and longer chain length had less fibrinogen adsorption, less fibrinogen γ-chain exposed, less adherent platelets, and lower activation of the adherent platelets. In addition to the influence on blood, the longer chain PEGylated surfaces resisted, not only smooth muscle cell attachment and proliferation, but also macrophage attachment and death. This method is a good candidate for improving cardiovascular implant surfaces.

Nonfouling poly(ethylene oxide) layers end-tethered to polydopamine

Nonfouling surfaces capable of reducing protein adsorption are highly desirable in a wide range of applications. Coating of surfaces with poly(ethylene oxide) (PEO), a water-soluble, nontoxic, and nonimmunogenic polymer, is most frequently used to reduce nonspecific protein adsorption. Here we show how to prepare dense PEO brushes on virtually any substrate by tethering PEO to polydopamine (PDA)-modified surfaces. The chain lengths of hetero-bifunctional PEOs were varied in the range of 45-500 oxyethylene units (M(n) = 2000-20,000). End-tethering of PEO chains was performed through amine and thiol headgroups from reactive polymer melts to minimize excluded volume effects. Surface plasmon resonance (SPR) was applied to investigate the adsorption of model protein solutions and complex biologic medium (human blood plasma) to the densely packed PEO brushes. The level of protein adsorption of human serum albumin and fibrinogen solutions was below the detection limit of the SPR measurements for all PEO chains end-tethered to PDA, thus exceeding the protein resistance of PEO layers tethered directly on gold. It was found that the surface resistance to adsorption of lysozyme and human blood plasma increased with increasing length and brush character of the PEO chains end-tethered to PDA with a similar or better resistance in comparison to PEO layers on gold. Furthermore, the chain density, thickness, swelling, and conformation of PEO layers were determined using spectroscopic ellipsometry (SE), dynamic water contact angle (DCA) measurements, infrared reflection-absorption spectroscopy (IRRAS), and vibrational sum-frequency-generation (VSFG) spectroscopy, the latter in air and water.

Surface chemistry to minimize fouling from blood-based fluids

Upon contact with bodily fluids/tissues, exogenous materials spontaneously develop a layer of proteins on their surface. In the case of biomedical implants and equipment, biological processes with deleterious effects may ensue. For biosensing platforms, it is synonymous with an overwhelming background signal that prevents the detection/quantification of target analytes present in considerably lower concentrations. To address this ubiquitous problem, tremendous efforts have been dedicated over the years to engineer protein-resistant coatings. There is now extensive literature available on stealth organic adlayers able to minimize fouling down to a few ng cm(-2), however from technologically irrelevant single-protein buffered solutions. Unfortunately, few coatings have been reported to present such level of performance when exposed to highly complex proteinaceous, real-world media such as blood serum and plasma, even diluted. Herein, we concisely review the surface chemistry developed to date to minimize fouling from these considerably more challenging blood-based fluids. Adsorption dynamics is also discussed.

Designing nanostructured block copolymer surfaces to control protein adhesion

The profile and conformation of proteins that are adsorbed onto a polymeric biomaterial surface have a profound effect on its in vivo performance. Cells and tissue recognize the protein layer rather than directly interact with the surface. The chemistry and morphology of a polymer surface will govern the protein behaviour. So, by controlling the polymer surface, the biocompatibility can be regulated. Nanoscale surface features are known to affect the protein behaviour, and in this overview the nanostructure of self-assembled block copolymers will be harnessed to control protein behaviour. The nanostructure of a block copolymer can be controlled by manipulating the chemistry and arrangement of the blocks. Random, A-B and A-B-A block copolymers composed of methyl methacrylate copolymerized with either acrylic acid or 2-hydroxyethyl methacrylate will be explored. Using atomic force microscopy (AFM), the surface morphology of these block copolymers will be characterized. Further, AFM tips functionalized with proteins will measure the adhesion of that particular protein to polymer surfaces. In this manner, the influence of block copolymer morphology on protein adhesion can be measured. AFM tips functionalized with antibodies to fibronectin will determine how the surfaces will affect the conformation of fibronectin, an important parameter in evaluating surface biocompatibility.

Substrate Micropatterning as a New in Vitro Cell Culture System to Study Myelination

Myelination is a highly regulated developmental process whereby oligodendrocytes in the central nervous system and Schwann cells in the peripheral nervous system ensheathe axons with a multilayered concentric membrane. Axonal myelination increases the velocity of nerve impulse propagation. In this work, we present a novel in vitro system for coculturing primary dorsal root ganglia neurons along with myelinating cells on a highly restrictive and micropatterned substrate. In this new coculture system, neurons survive for several weeks, extending long axons on defined Matrigel tracks. On these axons, myelinating cells can achieve robust myelination, as demonstrated by the distribution of compact myelin and nodal markers. Under these conditions, neurites and associated myelinating cells are easily accessible for studies on the mechanisms of myelin formation and on the effects of axonal damage on the myelin sheath.