Bactericidal activity and cytotoxicity of antibacterial monomer MDPB

Novel pit and fissure sealant with nano-CaF2 and antibacterial monomer: Fluoride recharge, microleakage, sealing ability and cytotoxicity

Conventional resin-based sealants release minimal fluoride ions (F) and lack antibacterial activity. The objectives of this study were to: (1) develop a novel bioactive sealant containing calcium fluoride nanoparticles (nCaF2) and antibacterial dimethylaminohexadecyl methacrylate (DMAHDM), and (2) investigate mechanical performance, F recharge and re-release, microleakage, sealing ability and cytotoxicity. Helioseal F served as commercial control. The initial F release from sealant containing 20% nCaF2 was 25-fold that of Helioseal F. After ion exhaustion and recharge, the F re-release from bioactive sealant did not decrease with increasing number of recharge and re-release cycles. Elastic modulus of new bioactive sealant was 44% higher than Helioseal F. The new sealant had excellent sealing, minimal microleakage, and good cytocompatibility. Hence, the nanostructured sealant had substantial and sustained F release and antibacterial activity, good sealing ability and biocompatibility. The novel bioactive nCaF2 sealant is promising to provide long-term F ions for caries prevention.

Recent Advances in Quaternary Ammonium Monomers for Dental Applications

Resin-based dental materials have been one of the ideal choices among various materials in the treatment of dental caries. However, resin-based dental materials still have some drawbacks, such as the lack of inherent antibacterial activity. Extensive research has been conducted on the use of novel quaternary ammonium monomers (QAMs) to impart antibacterial activity to dental materials. This review provides a comprehensive overview of the recent advances in quaternary ammonium monomers (QAMs) for dental applications. The current progress and limitations of QAMs are discussed based on the evolution of their structures. The functional diversification and enhancement of QAMs are presented. QAMs have the potential to provide long-term antibacterial activity in dental resin composites, thereby prolonging their service life. However, there is a need to balance antibacterial performance with other material properties and the potential impact on the oral microbiome and general health. Finally, the necessity for further scientific progress in the development of novel quaternary ammonium monomers and the optimization of dental resin formulations is emphasized.

Developments in resin-based composites

With the phasing down of dental amalgam use in response to the Minamata Convention, it is likely that resin-based composite restoratives will be the dental material of choice for the direct restoration of compromised dentition in the UK, at least for the foreseeable future. The current materials have a finite lifespan, with failures predominately due to either secondary caries or fracture. Consequently, there is considerable in vitro research reported each year with the intention of producing improved materials. This review describes the recent research in materials designed to have low polymerisation shrinkage and increased mechanical properties. Also described is research into materials that are either antimicrobial or are designed to release ions into the surrounding oral environment, with the aim of stimulating remineralisation of the surrounding dental tissues. It is hoped that by describing this recent research, clinicians will be able to gain some understanding of the current research that will potentially lead to new products that they can use to improve patient treatment in the future.

Provides an overview of recent research developments aimed at improving the performance of resin-based composites.

Details the recent developments in monomers and fillers to produce resin-based composites that either have lower polymerisation shrinkage or better mechanical properties compared to current commercially available products.

Describes recent research on developing resin-based composites that can act as potential sources of antimicrobial or remineralising agents.

Development of di-methacrylate quaternary ammonium monomers with antibacterial activity

Nine antibacterial di-methacrylate monomers based on bis-quaternary ammonium salts (bis-QAMs) were synthesized and structurally characterized. The biological activity of the bis-QAMs was tested in terms of minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) on different bacterial strains achieving promising results and, in most cases, a complete bactericidal effect using a bis-QAM concentration lower than 1 mg/mL. Two of the structures showed comparable and superior activity against S. mutans than the commercial monomer 12-methacryloyloxydodecyl pyridinium bromide (MDBP). All the bis-QAMs here described were able to inhibit S. mutans biofilm formation at a concentration equal to the MIC value. From the analysis of the obtained data, some correlation regarding the structure and the antibacterial activity of the bis-QAMs could be drawn: a flexible alkyl C₁₂ spacer between the two quaternary ammonium moieties increased the monomer antibacterial effect in comparison to the aromatic ones; the equilibrium between hydrophobic and hydrophilic moieties was directly correlated to the bactericidal range of action; the increase of the steric hindrance of the ammonium side groups might be both advantageous or disadvantageous to the antibacterial efficacy depending on the whole monomer chemical structure. Even though the possible correlation between the monomer structures and their bacteriostatic or bactericidal effect is under investigation, the monomers exhibited low cytotoxicity on human dental pulp stem cells, confirming their promising potential in the dental materials' field. STATEMENT OF SIGNIFICANCE: The use of dental resins with antibacterial monomers might prevent the formation of secondary caries at the restoration margins. For this purpose, a series of di-methacrylate bis-quaternary ammonium monomers (QAMs) was developed. Unlike antibacterial mono-methacrylate monomers already described in the literature, the synthesized di-methacrylate monomers have the potential of acting as cross-linkers stabilizing the polymeric network and bear two quaternary ammonium groups that increase their antibacterial ability. The QAMs exert bactericidal activity on both Gram(+) and Gram(-) bacterial strains maintaining at the same time good biocompatibility with the oral environment. Some structural elements of the monomers were clearly related to high antibacterial properties, and this can help design new active structures and better understand their mechanism of action.

Synthesis and Characterization of Methacrylate-Functionalized Betulin Derivatives as Antibacterial Comonomer for Dental Restorative Resins

Secondary caries is the primary cause of composite restoration failures, resulting from marginal leakage and bacterial accumulation in the oral environment. Antibacterial dental composites, especially antibacterial monomers, have emerged as a promising strategy to inhibit secondary caries, which is pivotal to prolonging the lifespan of dental restorations. In this work, monomethacrylate- and dimethacrylate-functionalized betulin derivatives (M₁Bet and M₂Bet) were synthesized via an esterification reaction and served as antibacterial comonomers to develop novel dental resin formulations, in which M₁Bet and M₂Bet were incorporated to partially or completely replace bisphenol A glycerolate dimethacrylate (Bis-GMA). The control resin was a mixture based on Bis-GMA and tri(ethyleneglycol) dimethacrylate (TEGDMA) with a weight ratio of 50:50 (5B5T). The effect of the resin compositions and the chemical structures of M₁Bet and M₂Bet on the rheology behavior, optical property, polymerization kinetics, mechanical performance, cell viability, and antibacterial activity of dental resins were systematically investigated. Among all materials, the 1M₂Bet4B5T resin with 10 wt % substitution of Bis-GMA by M₂Bet exhibited comparable viscosity, higher light transmittance, improved degree of conversion, and mechanical properties compared with 5B5T. After incubation for 24 h, this optimal resin also possessed the best antibacterial activity against Streptococcus mutans, which had a significantly lower bacterial concentration (1.53 × 10⁹ CFU/mL) than 5B5T (9.03 × 10⁹ CFU/mL). Introducing betulin-based comonomers into dental resins is a potential strategy to develop antibacterial dental materials without sacrificing physical-mechanical properties.

Recent Advances in the Development of Antimicrobial and Antifouling Biocompatible Materials for Dental Applications

The risk of secondary bacterial infections resulting from dental procedures has driven the design of antimicrobial and antifouling dental materials to curb pathogenic microbial growth, biofilm formation and subsequent oral and dental diseases. Studies have investigated approaches based primarily on contact-killing or release-killing materials. These materials are designed for addition into dental resins, adhesives and fillings or as immobilized coatings on tooth surfaces, titanium implants and dental prosthetics. This review discusses the recent developments in the different classes of biomaterials for antimicrobial and antifouling dental applications: polymeric drug-releasing materials, polymeric and metallic nanoparticles, polymeric biocides and antimicrobial peptides. With modifications to improve cytotoxicity and mechanical properties, contact-killing and anti-adhesion materials show potential for incorporation into dental materials for long-term clinical use as opposed to short-lived antimicrobial release-based coatings. However, extended durations of biocompatibility testing, and adjustment of essential biomaterial features to enhance material longevity in the oral cavity require further investigations to confirm suitability and safety of these materials in the clinical setting. The continuous exposure of dental restorative and regenerative materials to pathogenic microbes necessitates the implementation of antimicrobial and antifouling materials to either replace antibiotics or improve its rational use, especially in the day and age of the ever-increasing problem of antimicrobial resistance.

Comparative evaluation of compressive and flexural strength, fluoride release and bacterial adhesion of GIC modified with CPP-ACP, bioactive glass, chitosan and MDPB

Background. This study evaluated the incorporation of casein phosphopeptide-amorphous calcium phosphate (CPP-ACP), calcium sodium phosphosilicate bioactive glass (BAG), chitosan (CH), and methacryloyloxydodecylpyridinium bromide (MDPB) on the compressive and flexural strength, fluoride (F^‒ ) release, and bacterial adhesion of conventional glass-ionomer cement (C-GIC).

Methods. Modifications were implemented by adding CPP-ACP, BAG, and CH to the glass powder, while MDPB-GIC was prepared by incorporating MDPB to the liquid of C-GIC. Custom-made molds were used for specimen preparation. Compressive and flexural strengths were evaluated using a universal testing machine. F^‒ release was calculated with Erichrome cyanide reagent, using UV-spectrophotometry, at two time intervals of 24 hours and seven days. For bacterial adhesion, the test specimens were exposed to the bacterial suspension of Streptococcus mutans and Lactobacillus acidophilus for 4 hours, and the adherent bacteria were quantified using colorimetry as the optical density (OD).

Results. The incorporation of MDPB increased the flexural strength of C-GIC, with no effect on its compressive strength. CH significantly improved the compressive and flexural strength; modifications with CPP-ACP, BAG, and MDPB significantly improved the flexural strength of C-GIC. While MDPB-GIC released significantly higher F^‒ at 24 hours, CPP-ACP- and BAG-modified GICs were comparable to C-GIC on day 7. C-GIC exhibited the highest bacterial adhesion, and MDPB-GIC showed the least. The data were analyzed with one-way (ANOVA), and pairwise comparisons were made with Tukey HSD tests.

Conclusion. Hence, it can be concluded that the incorporation of CPP-ACP, BAG, and CH improved the mechanical properties of C-GIC, whereas MDPB improved the resistance of C-GIC to bacterial adhesion.

Antibacterial effect of a brominated self-etch adhesive on carious dentin - An in vivo study

OBJECTIVES

This in vivo study compared the antibacterial effect of a self-etch adhesive with and without the brominated monomer 12-methacryloyloxydodecyl-pyridinium bromide (MDPB) on carious dentin after selective caries removal.

METHODS

10 patients showing deep primary carious lesions at two posterior teeth without pulpal symptoms were included. At visit I, carious tissue was selectively removed and carious dentin was sampled with a sterile roundbur (Komet No. 18). One cavity was restored with composite (SDR, Ceram X; DENTSPLY DeTrey) using an MDPB-containing self-etch adhesive (Clearfil Protect Bond, Kuraray Noritake; PB). The other restoration served as a control (Clearfil SE Bond II, Kuraray Noritake; SE). At visit II after 8 weeks, carious dentin was sampled again. Bacterial growth in carious dentin was differentiated using microbial cultivation. Bacterial DNA from intact cells and cell-free DNA were quantified using 16S rRNA gene-based real-time PCR and the microbial community composition was analyzed by amplicon deep-sequencing. Wilcoxon test was applied for statistical analysis.

RESULTS

Both treatments showed a decrease of intact bacterial cells in carious dentin at visit II compared to visit I (PB: visit I: 1.1*10⁶, visit II: 1.7*10⁵ (p = 0.03); SE: visit I: 1.1*10⁷, visit II = 2.4*10⁵ (p = 0.002)). No statistically significant reduction of cell-free bacterial DNA was detected (PB: visit I: 6.1*10⁵, visit II: 1.6*10⁵ (p = 0.08); SE: visit I: 5.3*10⁵, visit II: 2.9*10⁵ (p = 0.10)). The decrease of intact cell-derived (p = 0.371) and cell-free DNA (p = 0.455) did not differ significantly between PB and SE. Lactobacillus was most abundant within the microbial community at both visits. Alpha-diversity was not affected by treatment and samples showed high intra- and interindividual diversity.

CONCLUSION AND CLINICAL SIGNIFICANCE

Both self-etch adhesives have an antibacterial effect due to a decrease of bacterial DNA after selective caries removal. However, the results do not reveal any additional antibacterial effect by MDPB. The study is registered with the German Clinical Trials Register (DRKS00011532).

Application of Antimicrobial Polymers in the Development of Dental Resin Composite

Dental resin composites have been widely used in a variety of direct and indirect dental restorations due to their aesthetic properties compared to amalgams and similar metals. Despite the fact that dental resin composites can contribute similar mechanical properties, they are more likely to have microbial accumulations leading to secondary caries. Therefore, the effective and long-lasting antimicrobial properties of dental resin composites are of great significance to their clinical applications. The approaches of ascribing antimicrobial properties to the resin composites may be divided into two types: The filler-type and the resin-type. In this review, the resin-type approaches were highlighted. Focusing on the antimicrobial polymers used in dental resin composites, their chemical structures, mechanical properties, antimicrobial effectiveness, releasing profile, and biocompatibility were included, and challenges, as well as future perspectives, were also discussed.

Novel low-shrinkage-stress nanocomposite with remineralization and antibacterial abilities to protect marginal enamel under biofilm

OBJECTIVES

Polymerization shrinkage stress may lead to marginal damage, microleakage and failure of composite restorations. The objectives of this study were to : (1) develop a novel nanocomposite with low-shrinkage-stress, antibacterial and remineralization properties to reduce marginal enamel demineralization under biofilms; (2) evaluate the mechanical properties of the composite and calcium (Ca) and phosphate (P) ion release; and (3) investigate the cytotoxicity of the new low-shrinkage-stress monomer in vitro.

METHODS

The low-shrinkage-stress resin consisted of urethane dimethacrylate (UDMA) and triethylene glycol divinylbenzyl ether (TEG-DVBE), and 3 % dimethylaminohexadecyl methacrylate (DMAHDM) and 20 % calcium phosphate nanoparticles (NACP) were added. Mechanical properties, polymerization shrinkage stress, and degree of conversion were evaluated. The growth of Streptococcus mutans (S. mutans) on enamel slabs with different composites was assessed. Ca and P ion releases and monomer cytotoxicity were measured.

RESULTS

Composite with DMAHDM and NACP had flexural strength of 84.9 ± 10.3 MPa (n = 6), matching that of a commercial control composite. Adding 3 % DMAHDM did not negatively affect the composite ion release. Under S. mutans biofilm, the marginal enamel hardness was 1.2 ± 0.1 GPa for the remineralizing and antibacterial group, more than 2-fold the 0.5 ± 0.07 GPa for control (p < 0.05). The polymerization shrinkage stress of the new composite was 40 % lower than that of traditional composite control (p < 0.05). The new monomers had fibroblast viability similar to that of traditional monomer control (p > 0.1).

CONCLUSION

A novel low-shrinkage-stress nanocomposite was developed with remineralizing and antibacterial properties. This new composite is promising to inhibit recurrent caries at the restoration margins by reducing polymerization stress and protecting enamel hardness.

Novel Bioactive and Therapeutic Root Canal Sealers with Antibacterial and Remineralization Properties

According to the American Dental Association Survey of Dental Services Rendered (published in 2007), 15 million root canal treatment procedures are performed annually. Endodontic therapy relies mainly on biomechanical preparation, chemical irrigation and intracanal medicaments which play an important role in eliminating bacteria in the root canal. Furthermore, adequate obturation is essential to confine any residual bacteria within the root canal and deprive them of nutrients. However, numerous studies have shown that complete elimination of bacteria is not achieved due to the complex anatomy of the root canal system. There are several conventional antibiotic materials available in the market for endodontic use. However, the majority of these antibiotics and antiseptics provide short-term antibacterial effects, and they impose a risk of developing antibacterial resistance. The root canal is a dynamic environment, and antibacterial and antibiofilm materials with long-term effects and nonspecific mechanisms of action are highly desirable in such environments. In addition, the application of acidic solutions to the root canal wall can alter the dentin structure, resulting in a weaker and more brittle dentin. Root canal sealers with bioactive properties come in direct contact with the dentin wall and can play a positive role in bacterial elimination and strengthening of the root structure. The new generation of nanostructured, bioactive, antibacterial and remineralizing additives into polymeric resin-based root canal sealers are discussed in this review. The effects of these novel bioactive additives on the physical and sealing properties, as well as their biocompatibility, are all important factors that are presented in this article.

Resin based restorative dental materials: characteristics and future perspectives

This review article compiles the characteristics of resin based dental composites and an effort is made to point out their future perspectives. Recent research studies along with few earlier articles were studied to compile the synthesis schemes of commonly used monomers, their characteristics in terms of their physical, mechanical and polymerization process with selectivity towards the input parameters of polymerization process. This review covers surface modification processes of various filler particles using silanes, wear behaviour, antimicrobial behaviour along with its testing procedures to develop the fundamental knowledge of various characteristics of resin based composites. In the end of this review, possible areas of further interests are pointed out on the basis of literature review on resin based dental materials.

Advancing antimicrobial strategies for managing oral biofilm infections

Effective control of oral biofilm infectious diseases represents a major global challenge. Microorganisms in biofilms exhibit increased drug tolerance compared with planktonic cells. The present review covers innovative antimicrobial strategies for controlling oral biofilm-related infections published predominantly over the past 5 years. Antimicrobial dental materials based on antimicrobial agent release, contact-killing and multi-functional strategies have been designed and synthesized for the prevention of initial bacterial attachment and subsequent biofilm formation on the tooth and material surface. Among the therapeutic approaches for managing biofilms in clinical practice, antimicrobial photodynamic therapy has emerged as an alternative to antimicrobial regimes and mechanical removal of biofilms, and cold atmospheric plasma shows significant advantages over conventional antimicrobial approaches. Nevertheless, more preclinical studies and appropriately designed and well-structured multi-center clinical trials are critically needed to obtain reliable comparative data. The acquired information will be helpful in identifying the most effective antibacterial solutions and the most optimal circumstances to utilize these strategies.

Hydrazone, benzohydrazones and isoniazid-acylhydrazones as potential antituberculosis agents

Aim: To evaluate the potential of three benzohydrazones (1–3), four acylhydrazones derived from isoniazid (INH-acylhydrazones) (4–7) and one hydrazone (8) as antituberculosis agents. Materials & methods: Inhibitory and bactericidal activities were determined for the reference Mycobacterium tuberculosis ( Mtb) strain and clinical isolates. Cytotoxicity, drug combinations and ethidium bromide accumulation assays were also performed. Results: The tested compounds (1–8) presented excellent antituberculosis activity with surprisingly inhibitory (0.12–250 μg/ml) and bactericidal values, even against multidrug-resistant Mtb clinical isolates. Compounds showed high selectivity index, with values reaching 1833.33, and a limited spectrum of activity. Some of the compounds (2 & 8) are also great inhibitors of bacillus efflux pumps. Conclusion: Benzohydrazones and INH-acylhydrazones may be considered scaffolds for the development of new anti- Mtb drugs.

Flow Cytometry Analysis of Antibacterial Effects of Universal Dentin Bonding Agents on Streptococcus mutans

There is no consensus on the antibacterial activity of dentin bonding systems (DBS). Many study models have been used to evaluate the antimicrobial activity of dental materials. In this study, a novel detection method, flow cytometry, was introduced. It allows for evaluation of the antibacterial activity of DBS, based on assessment of the disruption of the bacterial physical membrane induced by DBS. The aim of the study was to evaluate the antibacterial properties of selected dentin bonding systems against Streptococcus mutans. The highest antibacterial activity against S. mutans was observed for Adhese Universal (99.68% dead cells) and was comparable to that of Prime&Bond Universal, OptiBond Universal, or Clearfil Universal Bond Quick (p > 0.05). The lowest activity of all tested systems was displayed by the multi-mode adhesive, Universal Bond (12.68% dead bacteria cells), followed by the self-etch adhesive, OptiBond FL (15.58% dead bacteria cells). The present study showed that in the case of two-component DBS, the primer exhibited higher antimicrobial activity than the adhesive (or bond) itself.

Evaluation of biofilm formation on novel copper-catalyzed azide-alkyne cycloaddition (CuAAC)-based resins for dental restoratives

OBJECTIVE

For the past several decades, the resins used in dental restorations have been plagued with numerous problems, including their implication in biofilm formation and secondary caries. The need for alternative resins is critical, and evaluation of biofilm formation on these resins is essential. The aim of this study was to evaluate in vitro biofilm formation on the surface of novel copper(I)-catalyzed azide-alkyne cycloaddition (CuAAC)-based resins and composites.

METHODS

CuAAC-based resins/composites made from varying azide monomers and different copper concentrations were compared with BisGMA-TEGDMA resins/composites that served as the control. Biofilms were formed using a mono-species model containing a luciferase-expressing strain of Streptococcus mutans. Luciferase activity was measured and the number of viable bacteria was enumerated on biofilms associated with each resin and composite.

RESULTS

A significant reduction (p<0.05) in luciferase activity, and the number of viable bacteria recovered from biofilms on CuAAC-based resins and composites was observed in comparison to biofilms associated with the BisGMA-TEGDMA controls.

SIGNIFICANCE

CuAAC-based resins do still allow for the formation of biofilms; however, the statistically significant reduction of growth that was associated with the CuAAC resin may enhance the longevity of restorations that incorporate CuAAC-based materials.

Novel Bioactive and Therapeutic Dental Polymeric Materials to Inhibit Periodontal Pathogens and Biofilms

Periodontitis is a common infectious disease characterized by loss of tooth-supporting structures, which eventually leads to tooth loss. The heavy burden of periodontal disease and its negative consequence on the patient's quality of life indicate a strong need for developing effective therapies. According to the World Health Organization, 10⁻15% of the global population suffers from severe periodontitis. Advances in understanding the etiology, epidemiology and microbiology of periodontal pocket flora have called for antibacterial therapeutic strategies for periodontitis treatment. Currently, antimicrobial strategies combining with polymer science have attracted tremendous interest in the last decade. This review focuses on the state of the art of antibacterial polymer application against periodontal pathogens and biofilms. The first part focuses on the different polymeric materials serving as antibacterial agents, drug carriers and periodontal barrier membranes to inhibit periodontal pathogens. The second part reviews cutting-edge research on the synthesis and evaluation of a new generation of bioactive dental polymers for Class-V restorations with therapeutic effects. They possess antibacterial, acid-reduction, protein-repellent, and remineralization capabilities. In addition, the antibacterial photodynamic therapy with polymeric materials against periodontal pathogens and biofilms is also briefly described in the third part. These novel bioactive and therapeutic polymeric materials and treatment methods have great potential to inhibit periodontitis and protect tooth structures.

Preparation of a highly crosslinked biosafe dental nanocomposite resin with a tetrafunctional methacrylate quaternary ammonium salt monomer

The design of antimicrobial dental nanocomposite resin to prevent secondary dental caries and minimize biosafety problems is an important endeavor with both fundamental and practical implications.

Monomer Modifications of Denture Base Acrylic Resin: A Systematic Review and Meta-analysis

Background:

Methyl methacrylate monomer of denture base resins was modified with several monomers to achieve better physico-mechanical properties without compromising the biocompatibility. However, there are no consensuses on the best strategy to achieve best modified monomer.

Purpose:

To identify and evaluate the differences in the properties between conventional and modified monomers and to verify the influence of several variables on the properties of denture base acrylic resin.

Materials and Methods:

This study was executed by following the Preferred Reporting Items for Systematic Reviews and Meta-Analyses statement. In-vitro studies that investigated the properties of conventional and modified monomers were selected. Searches were carried out in the Ebscohost, PubMed, Semantic scholar and J-stage databases. The search commenced from the year 1995 and the last search was done till November 2018. A comparison was performed between modified and unmodified monomers. The analyses were carried out using fixed-effect models.

Results:

The meta-analysis results showed high heterogeneity in all aspects, and higher flexural strength for monomers modified with 20% methacrylic acid.

Conclusion:

Although the articles included in this meta-analysis showed high heterogeneity and high risk of bias, the in-vitro literature seems to suggest that use of modified monomers could improve the properties of denture base resins. Other variants of monomer modifications and their tested parameters were discussed in this systematic review as well. Dimensional accuracy is an unexplored variable to be evaluated extensively in the future researches.

Comparison of Antibacterial Adhesion When Salivary Pellicle Is Coated on Both Poly(2-hydroxyethyl-methacrylate)- and Polyethylene-glycol-methacrylate-grafted Poly(methyl methacrylate)

Although poly(2-hydroxyethyl methacrylate) (pHEMA) and polyethylene glycol methacrylate (PEGMA) have been demonstrated to inhibit bacterial adhesion, no study has compared antibacterial adhesion when salivary pellicle is coated on polymethyl methacrylate (PMMA) grafted with pHEMA and on PMMA grafted with PEGMA. In this study, PMMA discs were fabricated from a commercial orthodontic acrylic resin system (Ortho-Jet). Attenuated total reflection-Fourier transform infrared spectra taken before and after grafting confirmed that pHEMA and PEGMA were successfully grafted on PMMA. Contact angle measurements revealed PMMA-pHEMA to be the most hydrophilic, followed by PMMA-PEGMA, and then by PMMA. Zeta potential analysis revealed the most negative surface charges on PMMA-PEGMA, followed by PMMA-pHEMA, and then by PMMA. Confocal laser scanning microscopy showed green fluorescence in the background, indicating images that influenced the accuracy of the quantification of live bacteria. Both the optical density value measured at 600 nm and single plate-serial dilution spotting showed that pHEMA was more effective than PEGMA against Escherichia coli and Streptococcus mutans, although the difference was not significant. Therefore, the grafting of pHEMA and PEGMA separately on PMMA is effective against bacterial adhesion, even after the grafted PMMA were coated with salivary pellicle. Surface hydrophilicity, bactericidality, and Coulomb repulsion between the negatively charged bacteria and the grafted surface contributed to the effectiveness.

Bioactive Dental Composites and Bonding Agents Having Remineralizing and Antibacterial Characteristics

Current dental restorative materials are typically inert and replace missing tooth structures. This article reviews efforts in the development of a new generation of bioactive materials designed to not only replace the missing tooth volume but also possess therapeutic functions. Composites and bonding agents with remineralizing and antibacterial characteristics have shown promise in replacing lost minerals, inhibiting recurrent caries, neutralizing acids, repelling proteins, and suppressing biofilms and acid production. Furthermore, they have demonstrated a low cytotoxicity similar to current resins, with additional benefits to protect the dental pulp and promote tertiary dentin formation. This new class of bioactive materials shows promise in reversing lesions and inhibiting caries.

Antibacterial quaternary ammonium compounds in dental materials: A systematic review

OBJECTIVE

Quaternary ammonium compounds (QACs) represent one of the most effective classes of disinfectant agents in dental materials and resin nanocomposites. This reviews aims to give a wide overview on the research in the field of antibacterial QACs in dental materials and nanocomposites.

METHOD

An introduction to dental materials components as well as the microorganisms and methods of evaluation for the antimicrobial assays are presented. Then, the properties and synthesis route of QACs, as monomer and filler, are shown. Finally, antimicrobial monomers and fillers, specifically those contain quaternary ammonium salts (QASs), in dental materials are reviewed.

RESULTS

QACs have been used as monomer and micro/nanofiller in restorative dentistry. They possess one or more methacrylate functional groups to participate in polymerization reactions. QACs with multiple methacrylate groups can also be used as crosslinking agents. Furthermore, QACs with chain length from ∼12 to 16 have higher antimicrobial activity in cured dental resins. In general, increasing the chain length leads to a threshold value (critical point) and then it causes decrease in the antimicrobial activity.

SIGNIFICANCE

The current state of the art of dental materials and resin nanocomposites includes a wide variety of antimicrobial materials. Among them, QACs presents low cytotoxicity and excellent long-term antimicrobial activity without leaching out over time.

Developing a New Generation of Antimicrobial and Bioactive Dental Resins

Dental caries is prevalent, and secondary caries causes restoration failures. This article reviews recent studies on developing a new generation of bioactive resins with anticaries properties. Extensive effects were made to develop new antimicrobial composites, bonding agents, and other resins containing quaternary ammonium methacrylates to suppress plaque buildup and bacterial acid production. The effects of alkyl chain length and charge density and the antimicrobial mechanisms for chlorhexidine, nano-silver, quaternary ammonium methacrylates, and protein-repellent agents were discussed. Synergistic effects of contact-killing and protein-repellent properties were shown to yield the greatest biofilm-inhibition effects. The combination of antimicrobial, protein-repellent, and calcium phosphate nanoparticle remineralization was suggested to provide maximal anticaries effects. In addition, for use orally, cytotoxicity and biocompatibility were important considerations for the new bioactive materials. Furthermore, rather than kill all bacteria, it would be more desirable to modulate the oral biofilm compositions via bioactive resins to suppress cariogenic/pathogenic species and promote benign species. For widespread clinical use of the new antimicrobial and therapeutic materials, whether they would induce bacterial drug resistance needs to be determined, which requires further study. Nonetheless, the new generation of bioactive anticaries resins with therapeutic and biofilm acid-inhibiting properties has the potential to substantially benefit oral health.

Antibacterial Activity of Commercial Dentine Bonding Systems against E. faecalis-Flow Cytometry Study

Literature presents inconsistent results on the antibacterial activity of dentine bonding systems (DBS). Antibacterial activity of adhesive systems depends on several factors, including composition and acidity. Flow cytometry is a novel detection method to measure multiple characteristics of a single cell: total cell number, structural (size, shape), and functional parameters (viability, cell cycle). The LIVE/DEAD^® BacLight™ bacterial viability assay was used to evaluate an antibacterial activity of DBS by assessing physical membrane disruption of bacteria mediated by DBS. Ten commercial DBSs: four total-etching (TE), four self-etching (SE) and two selective enamel etching (SEE) were tested. Both total-etching DBS ExciTE F and OptiBond Solo Plus showed comparatively low antibacterial activity against E. faecalis. The lowest activity of all tested TE systems showed Te-Econom Bond. Among SE DBS, G-ænial Bond (92.24% dead cells) followed by Clearfil S3 Bond Plus (88.02%) and Panavia F 2.0 ED Primer II (86.67%) showed the highest antibacterial activity against E. faecalis, which was comparable to isopropranol (positive control). In the present study, self-etching DBS exhibited higher antimicrobial activity than tested total-etching adhesives against E. faecalis.

Quaternary ammonium-based biomedical materials: State-of-the-art, toxicological aspects and antimicrobial resistance

Microbial infections affect humans worldwide. Many quaternary ammonium compounds have been synthesized that are not only antibacterial, but also possess antifungal, antiviral and anti-matrix metalloproteinase capabilities. Incorporation of quaternary ammonium moieties into polymers represents one of the most promising strategies for preparation of antimicrobial biomaterials. Various polymerization techniques have been employed to prepare antimicrobial surfaces with quaternary ammonium functionalities; in particular, syntheses involving controlled radical polymerization techniques enable precise control over macromolecular structure, order and functionality. Although recent publications report exciting advances in the biomedical field, some of these technological developments have also been accompanied by potential toxicological and antimicrobial resistance challenges. Recent evidenced-based data on the biomedical applications of antimicrobial quaternary ammonium-containing biomaterials that are based on randomized human clinical trials, the golden standard in contemporary medicinal science, are included in the present review. This should help increase visibility, stimulate debates and spur conversations within a wider scientific community on the implications and plausibility for future developments of quaternary ammonium-based antimicrobial biomaterials.

Antibacterial Activity and Bonding Ability of an Orthodontic Adhesive Containing the Antibacterial Monomer 2-Methacryloxylethyl Hexadecyl Methyl Ammonium Bromide

Irreversible white spot lesion (WSL) occurs in up to 50% of patients during orthodontic treatment. Therefore, orthodontic adhesives need to be able to inhibit or reduce bacterial growth in order to prevent or minimize WSL. This study evaluated the antibacterial effect and shear bond strength (SBS) of a resin-based orthodontic adhesive containing the antibacterial monomer 2-methacryloxylethyl hexadecyl methyl ammonium bromide (MAE-HB). MAE-HB was added at three concentrations (1, 3, and 5 wt%) to a commercial orthodontic adhesive Transbond XT, while the blank control comprised unmodified Transbond XT. Their antibacterial effects on Streptococcus mutans were investigated after 0 and 180 days of aging. The SBS of metal brackets bonded to the buccal enamel surface of human premolars was assessed. Compared with the blank control, the MAE-HB-incorporated adhesive exhibited a significant contact inhibitory effect on the growth of S. mutans (P < 0.05), even after 180 days of aging. SBS and adhesive remnant index values revealed that the bonding ability of the experimental adhesive was not significantly adversely affected by the incorporation of MAE-HB at any of the three concentrations. Therefore, orthodontic adhesives with strong and long-lasting bacteriostatic properties can be created through the incorporation of MAE-HB without negatively influencing bonding ability.

Flowable composites for restoration of non-carious cervical lesions: Three-year results

OBJECTIVES

To evaluate the clinical performance of two flowable composites for restoring Class-V non-carious cervical lesions (NCCLs), one with novel (ND; N'Durance^® Dimer Flow, Septodont) and one with modified conventional matrix composition (FS; Filtek™ Supreme XTE Flow, 3M-ESPE). The null hypothesis was that both flowable composites perform equally regarding clinical quality and survival.

METHODS

50 patients received one ND and one FS restoration of NCCLs in premolars using Clearfil Protect Bond (Kuraray) as an adhesive. Restorations were evaluated by two examiners at baseline (BL), 18 and 36 months employing FDI criteria. Non-parametric statistical analyses and χ² tests were applied (α=0.05).

RESULTS

48 patients with both restorations under risk participated in the 36-mo recall. One patient terminated participation after the 18-mo recall. One ND restoration failed at the 18-mo recall (fracture). One FS restoration failed during clinical examination at the 36-mo recall (debonding). 95.8% of restorations each were rated clinically acceptable at 36-mo. No significant differences for all selected FDI criteria were recorded between ND and FS at each examination time point except for the criteria surface staining at 36-mo and marginal staining at 18-mo and 36-mo, where FS showed significantly better results. For each material, no significant differences over time were detected, except for loss of surface lustre for FS (BL to 18 months).

SIGNIFICANCE

Within the limitations of the study, the null hypothesis that materials perform equally could not be rejected. Both flowable composites performed equally regarding survival and similarly regarding clinical performance.

Development of a Cavity Disinfectant Containing Antibacterial Monomer MDPB

An experimental cavity disinfectant (ACC) that is intended to be used for various direct and indirect restorations was prepared by adding an antibacterial monomer 12-methacryloyloxydodecylpyridinum bromide (MDPB) at 5% into 80% ethanol. The antibacterial effectiveness of ACC and its influences on the bonding abilities of resin cements were investigated. To examine the antibacterial activity of unpolymerized MDPB, the minimum inhibitory and bactericidal concentrations (MIC and MBC) were determined for Streptococcus mutans, Lactobacillus casei, Actinomyces naeslundii, Parvimonas micra, Enterococcus faecalis, Fusobacterium nucleatum, and Porphyromonas gingivalis. Antibacterial activities of ACC and the commercial cavity disinfectant containing 2% chlorhexidine and ethanol (CPS) were evaluated by agar disk diffusion tests through 7 bacterial species and by MIC and MBC measurement for S. mutans. The effects of ACC and CPS to kill bacteria in dentinal tubules were compared with an S. mutans–infected dentin model. Shear bond strength tests were used to examine the influences of ACC on the dentin-bonding abilities of a self-adhesive resin cement and a dual-cure resin cement used with a primer. Unpolymerized MDPB showed strong antibacterial activity against 7 oral bacteria. ACC produced inhibition zones against all bacterial species similar to CPS. For ACC and CPS, the MIC value for S. mutans was identical, and the MBC was similar with only a 1-step dilution difference (1:2). Treatment of infected dentin with ACC resulted in significantly greater bactericidal effects than CPS ( P < 0.05, analysis of variance and Tukey’s honest significant difference test). ACC showed no negative influences on the bonding abilities to dentin for both resin cements, while CPS reduced the bond strength of the self-adhesive resin cement ( P < 0.05). This study clarified that the experimental cavity disinfectant containing 5% MDPB is more effective in vitro than the commercially available chlorhexidine solution to eradicate bacteria in dentin, without causing any adverse influences on the bonding abilities of resinous luting cements.

Effect of an Antibacterial Monomer on the Antibacterial Activity of a Pit-and-Fissure Sealant

Resin-based pit-and-fissure sealants are often used to form a barrier on the occlusal surface of molars to treat caries lesions; however, bacteria can remain in the pit and fissures without detection, increasing the risk of secondary caries. Sealants with antimicrobial properties or microbial repellent actions might be advantageous. The aim of this study was to assess the inhibitory effect of a 2-methacryloxylethyl dodecyl methyl ammonium bromide (MAE-DB)-incorporated sealant against Streptococcus mutans. MAE-DB (4% wt) was incorporated into a commercially available sealant, Eco-S resin-based pit-and-fissure sealant (Vericom Co., Ltd., Korea); a sealant without MAE-DB served as a negative control, and Clinpro™ Sealant (3M™ ESPE™), a fluoride-releasing resin, was used as a commercial control. The effects of the cured sealants and their eluents on the growth of S. mutans were determined according to colony-forming unit counts and metabolic tests. The effects of the cured sealants on the adherence and membrane integrity of S. mutans were investigated using confocal laser-scanning microscopy (CLSM) in conjunction with fluorescent indicators. Compared with the negative control and commercial control, the cured MAE-DB-incorporated pit-and-fissure sealant exhibited a significant inhibitory effect on the growth of S. mutans (P < 0.05), whereas the eluents did not show any detectable antibacterial activity. The commercial control also showed no detectable bactericidal activity. Moreover, the aged experimental material retained its property of contact inhibition of biofilm formation. The fluorescence analysis of CLSM images demonstrated that the cured MAE-DB-incorporated sealant could hamper the adherence of S. mutans and exert a detrimental effect on bacterial membrane integrity. The incorporation of MAE-DB can render a pit-and-fissure sealant with contact antibacterial activity after polymerization via influencing the growth, adherence, and membrane integrity of S. mutans. Therefore, MAE-DB-containing pit-and-fissure sealant shows promise for preventing or controlling dental caries on occlusal pit and fissures of molars.

Antibacterial activity of a modified unfilled resin containing a novel polymerizable quaternary ammonium salt MAE-HB

Resins with strong and long-lasting antibacterial properties are critical for the prevention of secondary dental caries. In this study, we evaluated the antibacterial effect and the underlying mechanism of action of an unfilled resin incorporating 2-methacryloxylethyl hexadecyl methyl ammonium bromide (MAE-HB) against Streptococcus mutans UA159 (S. mutans UA159). MAE-HB was added into unfilled resin at 10 mass%, and unfilled resin without MAE-HB served as the control. Bacterial growth was inhibited on 10%-MAE-HB unfilled resin compared with the control at 1 d, 7 d, 30 d, or 180 d (P < 0.05). The growth inhibitory effect was independent of the incubation time (P > 0.05). No significant differences in the antibacterial activities of eluents from control versus 10%-MAE-HB unfilled resins were observed at any time point (P > 0.05). The number of bacteria attached to 10%-MAE-HB unfilled resin was considerably lower than that to control. Fe-SEM and CLSM showed that 10%-MAE-HB unfilled resin disturbed the integrity of bacterial cells. Expression of the bacterial glucosyltransferases, gtfB and gtfC, was lower on 10%-MAE-HB unfilled resin compared to that on control (P < 0.05). These data indicate that incorporation of MAE-HB confers unfilled resin with strong and long-lasting antibacterial effects against S. mutans.

Cytotoxicity of Two-step Self-etching Primer/Adhesives on L929 Cells

The cytotoxicity of four self-etching primer/adhesive systems (Clearfil® SE Bond, Clearfil® Protect Bond, Mac Bond® II and FL® Bond) was tested against L929 fibroblasts. The primer or adhesive component of each adhesive system was diluted serially with the culture medium at a ratio of 1:1,000 and 1:4,000 (v/v). Cytotoxicity was identified by adding L929 cells in 24-well culture plates at an initial density of 35,000 cells mL 1. The cells were maintained for 5 days; every 24h, the medium was changed with fresh medium containing specific dilutions of the primer or adhesive components of the test materials. Cytotoxicity was assessed quantitatively at 24, 48, 72, 96 and 120h. Physiological and pathological cellular changes as well as reactions and growth of the cell cultures were examined under an inverted microscope. All self-etching systems were found to be cytotoxic to varying degrees; more pronounced toxic effects were observed at lower dilution (1:1,000 [v/v]). The adhesive components of Mac Bond® II and FL® Bond showed the highest cytotoxicity at 1:1,000 (v/v). The primer and adhesive of Clearfil® SE Bond, the primer of Mac Bond® II and the antibacterial monomer (MDPB)-containing Clearfil® Protect Bond (at 1:4,000 [v/v]) were relatively less cytotoxic.

Evolution of resistance to cationic biocides in Streptococcus mutans and Enterococcus faecalis

OBJECTIVES

The aim of this study was to investigate whether Streptococcus mutans and Enterococcus faecalis develop resistance to the cationic biocides chlorhexidine (CHX), cetylpyridinium chloride (CPC), and 12-methacryloyloxydodecylpyridinium bromide (MDPB).

METHODS

The minimum inhibitory concentrations (MICs) of CHX, CPC, and MDPB were assessed after repeated exposure of S. mutans and E. faecalis to these biocides. Cell-surface hydrophobicity and protein expression profiles of bacterial cells were examined to elucidate possible resistance mechanisms.

RESULTS

The MIC of CHX against E. faecalis showed constant increases up to 10 passages. No changes in the MICs of CPC and MDPB against E. faecalis were observed. The MICs of CHX, CPC, and MDPB against S. mutans did not increase. The surface hydrophobicity of E. faecalis significantly increased with increasing exposure to CHX and CPC. However, changes in protein expression profiles were only found in CHX-adapted E. faecalis, as evidenced by the emergence of a novel, approximately 19-kDa band following sodium dodecyl sulfate-polyacrylamide gel electrophoresis.

CONCLUSIONS

While E. faecalis and S. mutans did not exhibit increased resistance to CPC or MDPB, repeated exposure of E. faecalis to CHX led to resistance. It is likely that the acquisition of resistance is related to an altered protein composition.

CLINICAL SIGNIFICANCE

Alkyl pyridinium compounds, such as CPC and MDPB, could have a lower risk to cause adaptation of E. faecalis, which is advantageous compared with CHX.

Photocurable, Antimicrobial Quaternary Ammonium-modified Nanosilica

In this study, novel, quaternary ammonium methacrylate-modified silica nanoparticles (QMSNs) were synthesized for the first time and proposed as possible antimicrobial particles for free-radical, photocurable monomers. Such monomers have the potential to polymerize with other methacrylate monomers and create antimicrobial polymers. The silica nanoparticles were modified by quaternary ammonium methacrylate functionality and incorporated at 0 to 10 wt% into a 1:1 (by mass) bisphenol A glycerolate dimethacrylate (BisGMA)/triethylene glycol dimethacrylate (TEGDMA) resin. Thermal stability of the pristine and modified silica nanoparticles was examined by thermogravimetric analyses. Atomic force microscopy was used to investigate the size distribution and topography of the nanoparticles. For evaluation of the mechanical properties of the samples, flexural strength was measured using a 3-point bending test method. The flexural strength of the composites containing QMSNs increased with increasing modified silica content. The antimicrobial activity of samples was investigated against some standard microorganisms (Streptococcus mutans, Staphylococcus aureus, Bacillus subtilis, Escherichia coli, Pseudomonas aeruginosa, and Candida albicans), and then cytotoxicity and viability were quantified. Incorporation of 2.5% to 10% (by mass) QMSNs into BisGMA/TEGDMA demonstrated antimicrobial activity, but ≥5 wt% significantly reduced cell viability.

The Use of Quaternary Ammonium to Combat Dental Caries

Resin composites and adhesives are increasingly popular in dental restorations, but secondary caries is one of the main reasons for restoration failure. Quaternary ammonium monomers (QAMs) have an anti-microbial effect and are widely used in many fields. Since the concept of the immobilized antibacterial effect was put forward, dental restorations containing QAMs have been studied to reduce secondary caries. Previous studies have been struggling to develop novel anti-caries materials which might have triple benefits: good mechanical properties, antibacterial effects and remineralization potentials. Different kinds of QAMs have been proven to be effective in inhibiting the growth and metabolism of biofilms. Combination of QAMs and other nanoparticles in resin composites and adhesives could enhance their anti-caries capability. Therefore, QAMs are promising to show significant impact on the future of restorative and preventive dentistry.

Effect on vascular permeability of a self-etching adhesive system containing an antimicrobial quaternary ammonium polymer QAMP into subcutaneous tissue of rats

OBJECTIVE

This study investigated the effect of a self-etching adhesive system containing an antimicrobial quaternary ammonium methacrylate polymer (QAMP) on the vascular permeability using Evans blue and laser-Doppler flowmetric methods.

DESIGN

Forty rats were anesthetized and divided into groups: saline solution; Clearfil™ Protect Bond; Clearfil™ SE Bond; Clearfil™ SE Bond containing QAMP. Injections of Evans blue were administrated intravenously and the substances were injected intradermally. Immediately before injection and after 3 and 6h, was evaluated the blood flow. The animals were killed 3 and 6h after injection. The dorsal skin was dissected and experimental sites were obtained. The vascular permeability was evaluated by dye extravasation area, the dye was extracted and absorbance measured.

RESULTS

Concerning the Evans blue method, Clearfil™ SE Bond containing QAMP showed an extravasation area statistically similar to Clearfil™ SE Bond and lower than Clearfil™ Protect Bond. No statistical difference was verified among experimental groups for the amount of dye extracted. Clearfil™ SE Bond containing QAMP provided better laser-Doppler flowmetric parameters than Clearfil™ Protect Bond immediately and 3h after injection.

CONCLUSION

The QAMP had lower effect on the exudative phase of the inflammatory process.

Bacterial leakage in root canals filled with AH Plus and dentine bonding agents

OBJECTIVE

The aim of this study was to compare the efficacy of different dentine adhesives in delaying the coronal bacterial leakage of Enterococcus faecalis in filled root canals. Materials and methods. Ninety-five lower incisors of patients >65 years of age were instrumented using the ProTaper system and were irrigated with 1 mL of 2.5% sodium hypochlorite (NaOCl) alternated with 1 mL 17% EDTA between each file change. Final irrigation was performed with 5 mL of 17% EDTA and then flushed with 5 mL of distilled water. The teeth were randomly divided into five experimental groups (n = 15/group) and one of the following dentine adhesives was applied: (1) AdheSE; (2) Excite DSC; (3) Clearfil Protect Bond; (4) One Coat 7.0; or (5) Control group without adhesive. After filling the root canals, the samples were mounted on a double chamber device to evaluate the bacterial filtration of E. faecalis during a period of 240 days. The results underwent non-parametric Kaplan-Meier survival analysis and comparisons among groups were done using the Log-Rank test.

RESULTS

At 240 days, E. faecalis was detected in samples of all groups in the lower chamber. The highest survival value was obtained by One Coat 7.0, giving statistically significant differences from the other groups, whereas Clearfil Protect Bond, AdheSE and Excite DSC showed similar behaviours, likewise similar to the Control group.

CONCLUSIONS

One Coat 7.0 adhesive system provides the longest survival value to delay E. faecalis coronal leakage in filled root canals.

Restoration materials and secondary caries using an in vitro biofilm model

This in vitro study investigated whether restoration materials and adhesives influence secondary caries formation in gaps using a short-term in vitro biofilm model. Sixty enamel-dentin blocks were restored with 6 different restoration materials with or without adhesives (n = 10 per group) with a gap: 1) Clearfil AP-X composite, 2) Clearfil AP-X composite + SE Bond, 3) Clearfil AP-X composite + ProtectBond, 4) Filtek Silorane composite, 5) Filtek Silorane composite + Silorane System adhesive, or 6) Tytin amalgam. Specimens were subjected to an intermittent 1% sucrose biofilm model for 20 days to create artificial caries lesions. Lesion progression in the enamel-dentin next to the different materials was measured in lesion depth (LD) and mineral loss (ML) using transversal wavelength independent microradiography (T-WIM). A regression analysis was used to compare the LD and ML of the different restoration materials at 4 measurement locations: 1 location at the surface of the enamel, 1 location at the wall of the enamel, and 2 locations at the wall of the dentin. A statistically significant effect of AP-X composite with Protect Bond was found for LD and ML at the WallDentin1 location, leading to less advanced wall lesions. An additional finding was that gap size was also statistically significant at the 2 wall locations in dentin, leading to increasing lesion progression with wider gaps. In conclusion, adhesives can influence wall lesion development in gaps. Protect Bond showed significantly less caries progression compared to bare restoration materials or other adhesives in this short-term in vitro biofilm model.

Development of an antibacterial root canal filling system containing MDPB

An antibacterial monomer 12-methacryloyloxydodecylpyridinum bromide (MDPB)-containing experimental, chemically cured primer was prepared to develop a new resin-based root canal filling system. This study investigated the antibacterial effects of the MDPB-containing primer (experimental primer [EP]) against Enterococcus faecalis and assessed the in vitro bonding and sealing abilities of the filling system, consisting of EP and a Bis-GMA-based sealer resin. Antibacterial effects of EP were evaluated by contact with planktonic or adherent bacteria for 30 or 60 sec, and the viable bacterial number was counted. The antibacterial effects against E. faecalis in dentinal tubules were also assessed, according to a root canal infection model. Bonding and sealing abilities of the experimental filling system were examined by microtensile bond strength tests and leakage tests based on fluid filtration methods. Significantly greater reduction in viable bacteria in planktonic and adherent form was obtained by short-period contact with EP compared with the control primer (without MDPB) or with the proprietary (Epiphany) primer (p < .05). Significantly greater bactericidal effects of the EP inside the dentinal tubule of root, as opposed to the control primer or Epiphany primer, were confirmed according to a root canal infection model (p < .05), and 100% killing of E. faecalis could be obtained by the application of EP after irrigation with a 5% sodium hypochlorite solution. The experimental endodontic filling system demonstrated significantly greater bond strength to root dentin than Epiphany sealer system (Epiphany primer and Epiphany Root Canal Sealant; p < .05), showing formation of resin tags and a hybridized layer. Leakage tests clarified that the experimental system provided excellent sealing. This study confirmed that the MDPB-containing experimental antibacterial primer has the ability to effectively disinfect the root canal. Additionally, the experimental root canal filling system employing this primer and the Bis-GMA-based sealer resin is useful for achieving good sealing, suggesting its possible benefit for successful endodontic treatments.

Evaluation of antibacterial and remineralizing nanocomposite and adhesive in rat tooth cavity model

Antibacterial and remineralizing dental composites and adhesives were recently developed to inhibit biofilm acids and combat secondary caries. It is not clear what effect these materials will have on dental pulps in vivo. The objectives of this study were to investigate the antibacterial and remineralizing restorations in a rat tooth cavity model, and determine pulpal inflammatory response and tertiary dentin formation. Nanoparticles of amorphous calcium phosphate (NACP) and antibacterial dimethylaminododecyl methacrylate (DMADDM) were synthesized and incorporated into a composite and an adhesive. Occlusal cavities were prepared in the first molars of rats and restored with four types of restoration: control composite and adhesive; control plus DMADDM; control plus NACP; and control plus both DMADDM and NACP. At 8 or 30days, rat molars were harvested for histological analysis. For inflammatory cell response, regardless of time periods, the NACP group and the DMADDM+NACP group showed lower scores (better biocompatibility) than the control group (p=0.014 for 8days, p=0.018 for 30days). For tissue disorganization, NACP and DMADDM+NACP had better scores than the control (p=0.027) at 30days. At 8days, restorations containing NACP had a tertiary dentin thickness (TDT) that was five- to six-fold that of the control. At 30days, restorations containing NACP had a TDT that was four- to six-fold that of the control. In conclusion, novel antibacterial and remineralizing restorations were tested in rat teeth in vivo for the first time. Composite and adhesive containing NACP and DMADDM exhibited milder pulpal inflammation and much greater tertiary dentin formation than the control adhesive and composite. Therefore, the novel composite and adhesive containing NACP and DMADDM are promising as a new therapeutic restorative system to not only combat oral pathogens and biofilm acids as shown previously, but also facilitate the healing of the dentin-pulp complex.

Effect of a novel quaternary ammonium methacrylate polymer (QAMP) on adhesion and antibacterial properties of dental adhesives

This study investigated the resin–dentin bond strength (μTBS), degree of conversion (DC), and antibacterial potential of an innovative adhesive system containing a quaternary ammonium methacrylate polymer (QAMP) using in situ and in vitro assays. Forty-two human third molars were flattened until the dentin was exposed and were randomly distributed into three groups of self-etching adhesive systems: Clearfil™ SE Bond containing 5% QAMP (experimental group), Clearfil™ Protect Bond (positive control) and Clearfil™ SE Bond (negative control). After light curing, three 1 mm-increments of composite resin were bonded to each dentin surface. A total of thirty of these bonded teeth (10 teeth per group) was sectioned to obtain stick-shaped specimens and tested under tensile stress immediately, and after 6 and 12 months of storage in distilled water. Twelve bonded teeth (4 teeth per group) were longitudinally sectioned in a mesio-to-distal direction to obtain resin-bonded dentin slabs. In situ DC was evaluated by micro-Raman spectroscopy. In vitro DC of thin films of each adhesive system was measured using Fourier transform infrared spectroscopy. In vitro susceptibility tests of these three adhesive systems were performed by the minimum inhibitory/minimum bactericidal concentration (MIC/MBC) assays against Streptococcus mutans, Lactobacillus casei, and Actinomyces naeslundii. No statistically significant difference in μTBS was observed between Clearfil™ SE Bond containing 5% QAMP and Clearfil™ SE Bond (p > 0.05) immediately, and after 6 and 12 months of water storage. However Clearfil™ Protect Bond showed a significant reduction of μTBS after 12 months of storage (p = 0.039). In addition, QAMP provided no significant change in DC after incorporating into Clearfil™ SE Bond (p > 0.05). Clearfil™ SE Bond containing 5% QAMP demonstrated MIC/MBC values similar to the positive control against L. casei and A. naeslundii and higher than the negative control for all evaluated bacterial strains. The use of QAMP in an adhesive system demonstrated effective bond strength, a suitable degree of conversion, and adequate antibacterial effects against oral bacteria, and may be useful as a new approach to provide long-lasting results for dental adhesives.

Mechanism of detoxification of the cationic antibacterial monomer 12-methacryloyloxydodecylpyridiniumbromide (MDPB) by N-acetyl cysteine

OBJECTIVES

The protective effects of N-acetyl cysteine (NAC) against cytotoxicity induced by conventional dental resin monomers have been widely documented. However, its effectiveness to detoxify cationic antibacterial monomers has not yet been elucidated. The aim of the present study was to investigate the possible protective effects of NAC against the cytotoxicity of 12-methacryloyloxydodecylpyridiniumbromide (MDPB) and explore the role of adduct formation in NAC-directed detoxification.

METHODS

The influences of NAC on the cytotoxicity of MDPB were studied in mouse osteoblast-like MC3T3-E1 cells using the MTT assay. Ultra-performance liquid chromatography (UPLC) and liquid chromatography-mass spectrometry (LC-MS) analysis were performed to investigate the possible chemical reaction between NAC and MDPB.

RESULTS

While only slight reduction in the cytotoxicity of MDPB by NAC was observed immediately after mixing with MDPB, remarkable protection against MDPB-induced cell death was detected when the mixture was tested after 24h of pre-incubation. UPLC and LC-MS analysis revealed that chemical binding of MDPB and NAC occurred under neutral conditions after 24h of pre-incubation.

SIGNIFICANCE

Our findings suggest that NAC reduces the toxicity of the cationic antibacterial monomer MDPB, and adduct formation is partially responsible for the detoxification ability of NAC against MDPB-induced cell damage.

Effects of quaternary ammonium chain length on antibacterial bonding agents

The objectives of this study were to synthesize new quaternary ammonium methacrylates (QAMs) with systematically varied alkyl chain lengths (CL) and to investigate, for the first time, the CL effects on antibacterial efficacy, cytotoxicity, and dentin bond strength of bonding agents. QAMs were synthesized with CL of 3 to 18 and incorporated into Scotchbond Multi-Purpose (SBMP) bonding agent. The cured resins were inoculated with Streptococcus mutans. Bacterial early attachment was investigated at 4 hrs. Biofilm colony-forming units (CFU) were measured after 2 days. With CL increasing from 3 to 16, the minimum inhibitory concentration and minimum bactericidal concentration were decreased by 5 orders of magnitude. Incorporating QAMs into SBMP reduced bacterial early attachment, with the least colonization at CL = 16. Biofilm CFU for CL = 16 was 4 log lower than SBMP control (p < .05). All groups had similar dentin bond strengths (p > .1). The new antibacterial materials had fibroblast/odontoblast viability similar to that of commercial controls. In conclusion, increasing the chain length of new QAMs in bonding agents greatly increased the antibacterial efficacy. A reduction in Streptococcus mutans biofilm CFU by 4 log could be achieved, without compromising bond strength and cytotoxicity. New QAM-containing bonding agents are promising for a wide range of restorations to inhibit biofilms.

Synthesis of new antibacterial quaternary ammonium monomer for incorporation into CaP nanocomposite

OBJECTIVES

Composites are the principal material for tooth cavity restorations due to their esthetics and direct-filling capabilities. However, composites accumulate biofilms in vivo, and secondary caries due to biofilm acids is the main cause of restoration failure. The objectives of this study were to: (1) synthesize new antibacterial monomers and (2) develop nanocomposite containing nanoparticles of amorphous calcium phosphate (NACP) and antibacterial monomer.

METHODS

Two new antibacterial monomers were synthesized: dimethylaminohexane methacrylate (DMAHM) with a carbon chain length of 6, and dimethylaminododecyl methacrylate (DMADDM) with a chain length of 12. A spray-drying technique was used to make NACP. DMADDM was incorporated into NACP nanocomposite at mass fractions of 0%, 0.75%, 1.5%, 2.25% and 3%. A flexural test was used to measure composite strength and elastic modulus. A dental plaque microcosm biofilm model with human saliva as inoculum was used to measure viability, metabolic activity, and lactic acid production of biofilms on composites.

RESULTS

The new DMAHM was more potent than a previous quaternary ammonium dimethacrylate (QADM). DMADDM was much more strongly antibacterial than DMAHM. The new DMADDM-NACP nanocomposite had strength similar to that of composite control (p>0.1). At 3% DMADDM in the composite, the metabolic activity of adherent biofilms was reduced to 5% of that on composite control. Lactic acid production by biofilms on composite containing 3% DMADDM was reduced to only 1% of that on composite control. Biofilm colony-forming unit (CFU) counts on composite with 3% DMADDM were reduced by 2-3 orders of magnitude.

SIGNIFICANCE

New antibacterial monomers were synthesized, and the carbon chain length had a strong effect on antibacterial efficacy. The new DMADDM-NACP nanocomposite possessed potent anti-biofilm activity without compromising load-bearing properties, and is promising for antibacterial and remineralizing dental restorations to inhibit secondary caries.

Effect of water-aging on the antimicrobial activities of an ORMOSIL-containing orthodontic acrylic resin

Quaternary ammonium methacryloxy silicate (QAMS), an organically modified silicate (ORMOSIL) functionalized with polymerizable methacrylate groups and an antimicrobial agent with a long lipophilic alkyl chain quaternary ammonium group, was synthesized through a silane-based sol-gel route. By dissolving QAMS in methyl methacrylate monomer, this ORMOSIL molecule was incorporated into an auto-polymerizing, powder/liquid orthodontic acrylic resin system, yielding QAMS-containing poly(methyl methacrylate). The QAMS-containing acrylic resin showed a predominant contact-killing effect on Streptococcus mutans (ATCC 35668) and Actinomyces naeslundii (ATCC 12104) biofilms, while inhibiting adhesion of Candida albicans (ATCC 90028) on the acrylic surface. The antimicrobial activities of QAMS-containing acrylic resin were maintained after a 3month water-aging period. Bromophenol blue assay showed minimal leaching of quaternary ammonium species when an appropriate amount of QAMS (<4wt.%) was incorporated into the acrylic resin. The results suggest that QAMS is predominantly co-polymerized with the poly(methyl methacrylate) network, and only a minuscule amount of free QAMS molecules is present within the polymer network after water-aging. Acrylic resin with persistent antimicrobial activities represents a promising method for preventing bacteria- and fungus-induced stomatitis, an infectious disease commonly associated with the wearing of removable orthodontic appliances.