The influence of carrier morphology on drug delivery by dry powder inhalers

A Review on Micro and Nanoengineering in Powder-Based Pulmonary Drug Delivery

Pulmonary delivery of drugs has emerged as a promising approach for the treatment of both lung and systemic diseases. Compared to other drug delivery routes, inhalation offers numerous advantages including high targeting, fewer side effects, and a huge surface area for drug absorption. However, the deposition of drugs in the lungs can be limited by lung defence mechanisms such as mucociliary and macrophages' clearance. Among the delivery devices, dry powder inhalers represent the optimal choice due to their stability, ease of use, and absence of propellants. In the last decades, several bottom-up techniques have emerged over traditional milling to produce inhalable powders. Among these techniques, the most employed ones are spray drying, supercritical fluid technology, spray freeze-drying, and thin film freezing. Inhalable dry powders can be constituted by micronized drugs attached to a coarse carrier (e.g., lactose) or drugs embedded into a micro- or nanoparticle. Particulate-based formulations are commonly composed of polymeric micro- and nanoparticles, liposomes, solid lipid nanoparticles, dendrimers, nanocrystals, extracellular vesicles, and inorganic nanoparticles. Moreover, engineered formulations including large porous particles, swellable microparticles, nano-in-microparticles, and effervescent nanoparticles have been developed. Particle engineering has also a crucial role in tuning the physical-chemical properties of both carrier-based and carrier-free inhalable powders. This approach can increase powder flowability, deposition, and targeting by customising particle surface features.

Dry powder inhaler design and particle technology in enhancing Pulmonary drug deposition: challenges and future strategies

OBJECTIVES

The efficient delivery of drugs from dry powder inhaler (DPI) formulations is associated with the complex interaction between the device design, drug formulations, and patient's inspiratory forces. Several challenges such as limited emitted dose of drugs from the formulation, low and variable deposition of drugs into the deep lungs, are to be resolved for obtaining the efficiency in drug delivery from DPI formulations. The objective of this study is to review the current challenges of inhaled drug delivery technology and find a way to enhance the efficiency of drug delivery from DPIs.

METHODS/EVIDENCE ACQUISITION

Using appropriate keywords and phrases as search terms, evidence was collected from the published articles following SciFinder, Web of Science, PubMed and Google Scholar databases.

RESULTS

Successful lung drug delivery from DPIs is very challenging due to the complex anatomy of the lungs and requires an integrated strategy for particle technology, formulation design, device design, and patient inhalation force. New DPIs are still being developed with limited performance and future device design employs computer simulation and engineering technology to overcome the ongoing challenges. Many issues of drug formulation challenges and particle technology are concerning factors associated with drug dispersion from the DPIs into deep lungs.

CONCLUSION

This review article addressed the appropriate design of DPI devices and drug formulations aligned with the patient's inhalation maneuver for efficient delivery of drugs from DPI formulations.

Critical attributes of fine excipient materials in carrier-based dry powder inhalation formulations: The particle shape and surface properties

The potential of fine excipient materials to improve the aerodynamic performance of carrier-based dry powder inhalation (DPI) formulations is well acknowledged but not fully elucidated. To improve the understanding of this potential, we studied two fine excipient materials: micronized lactose particles and silica microspheres. Inhalation formulations, each composed of a coarse lactose carrier, one of the two fine excipient materials (0.0-15.0 % w/w), and a spray-dried drug (fluticasone propionate) material (1.5 % w/w) were prepared. The physical structure, the flow behavior, the aerosolization behavior, and the aerodynamic performance of the formulations were studied. The two fine excipient materials similarly occupied carrier surface macropores. However, only the micronized lactose particles formed agglomerates and appeared to increase the tensile strength of the formulations. At 2.5 % w/w, the two fine excipient materials similarly improved drug dispersibility, whereas at higher concentrations, the micronized lactose material was more beneficial than the silica microspheres. The findings suggest that fine excipient materials improve drug dispersibility from carrier-based DPI formulations at low concentrations by filling carrier surface macropores and at high concentrations by forming agglomerates and/or enforcing fluidization. The study emphasizes critical attributes of fine excipient materials in carrier-based DPI formulations.

Emerging Process Modeling Capabilities for Dry Powder Operations for Inhaled Formulations

Dry powder inhaler (DPI) products are commonly formulated as a mixture of micronized drug particles and large carrier particles, with or without additional fine particle excipients, followed by final powder filling into dose containment systems such as capsules, blisters, or reservoirs. DPI product manufacturing consists of a series of unit operations, including particle size reduction, blending, and filling. This review provides an overview of the relevant critical process parameters used for jet milling, high-shear blending, and dosator/drum capsule filling operations across commonly utilized instruments. Further, this review describes the recent achievements regarding the application of empirical and mechanistic models, especially discrete element method (DEM) simulation, in DPI process development. Although to date only limited modeling/simulation work has been accomplished, in the authors' perspective, process design and development are destined to be more modeling/simulation driven with the emphasis on evaluating the impact of material attributes/process parameters on process performance. The advancement of computational power is expected to enable modeling/simulation approaches to tackle more complex problems with better accuracy when dealing with real-world DPI process operations.

Dry Powder Inhalation for Lung Delivery in Cystic Fibrosis

Pulmonary drug delivery has long been used for local and systemic administration of different medications used in acute and chronic respiratory diseases. Certain lung diseases, such as cystic fibrosis, rely heavily on chronic treatments, including targeted lung delivery. Pulmonary drug delivery possesses various physiological advantages compared to other delivery methods and is also convenient for the patient to use. However, the formulation of dry powder for pulmonary delivery proves challenging due to aerodynamic restrictions and the lower tolerance of the lung. The aim of this review is to provide an overview of the respiratory tract structure in patients with cystic fibrosis, including during acute and chronic lung infections and exacerbations. Furthermore, this review discusses the advantages of targeted lung delivery, including the physicochemical properties of dry powder and factors affecting clinical efficacy. Current inhalable drug treatments and drugs currently under development will also be discussed.

Role of dispersion enhancer selection in the development of novel tratinterol hydrochloride dry powder inhalation formulations

Tratinterol hydrochloride (TH) is a new long-acting bronchodilator with strong β₂ adrenoceptor stimulation activity. The aim of this study was to design a new carrier-based dry powder inhalation (DPI) formulation for TH and to investigate the effect of dispersion enhancers on the aerosol performance of TH in vitro. To this end, coarse lactose was used as a carrier. TH was micronized by using a jet mill and blended with the carrier to obtain a reference DPI formulation. Commercial magnesium stearate (MgSt) as received, micronized MgSt (MgSt-M), and fine lactose (FL) were used as the dispersion enhancers and formulated with the micronized TH (TH-M) and the carrier as DPI formulations. The obtained DPI formulations were characterized using dynamic light scattering (DLS), X-ray powder diffraction (XRPD), thermal analysis, powder rheometer, and Raman microscopy. A next generation pharmaceutical impactor (NGI) was used to evaluate the aerodynamic performance of the dry powders. The results showed that TH-M was in an inhalable particle size range, and based on the XRPD and thermal analysis, the solid form of TH-M did not change compared to the starting materials. The NGI results showed that the fine particle fraction (FPF) of TH could be increased with the addition of MgSt and FL as dispersion enhancers in the reference formulation. In addition, the FPF of TH could be increased with a decrease in the particle size of MgSt or an increase in the amount of FL. A combination of MgSt-M and FL could further improve the aerosol performance of TH. Raman spectroscopic imaging confirmed the spatial location of MgSt and TH at the surface of the carrier. This study demonstrates that TH could be formulated into carrier-based dry powder formulation for inhalation using coarse lactose as the carrier. The dual strategy based on using both MgSt and FL as dispersion enhancers improved the aerosol performance of a novel TH dry powder formulation.

Sodium hyaluronate dry powder inhalation in combination with sodium cromoglycate prepared using optimized spray drying conditions

Sodium hyaluronate (SHA) is an anti-inflammatory and protective agent against bronchoconstriction, and sodium cromoglicate (SCG) prevents exercise-induced bronchoconstriction and inflammation. Based on the pharmacological properties of both substances, this study aimed to develop a dry powder inhaler (DPI) of SHA alone and in combination with SCG. The target of the study was to develop flowable formulations without any surfactants by using the spray drying method. To obtain respirable SHA and SCG:SHA particles, variables of the spray dryer, such as inlet temperature, atomized air flow, and feed solution, were changed. The particles 1-8 μm in size were produced with high yield by spray drying and increasing the ethanol percentage of the feed solution (60%), which is the most remarkable parameter. After that, physicochemical characterizations were performed. The aerosol performance of DPI formulations prepared using lactose was evaluated using Handihaler® DPI. The fine particle fraction (FPF) was 36% for the SHA formulation, whereas it was 52 and 53% for SCG and SHA, respectively, in the SCG:SHA formulation. Consequently, both particles were produced reproducibly by spray drying, and inhaled SHA and SCG:SHA dry powder formulations were developed due to their high FPF and flowability with lactose.

Surface Modification of lactose carrier particles using a fluid bed coater to improve fine particle fraction for dry powder inhalers

Surface roughness of carrier particles can impact dry powder inhaler (DPI) performance. There are opposing views on the effect of roughness on DPI performance. Hence, a systematic approach is needed to modify carrier surfaces and evaluate the impact on drug delivery. Carrier particle surfaces were modified by fluid bed coating with saturated lactose containing micronized lactose of different sizes (2, 5 and 8 μm) and coated to different levels (20, 40, 60 and 80%). Their drug delivery performance was assessed by the fine particle fraction (FPF). Roughness parameters, mean arithmetic roughness (R_a) and arithmetic mean height (S_a), of the carrier particles, were also evaluated using optical profilometry and scanning laser microscopy. Generally, particles of higher R_a had higher FPF. Higher S_a resulted in higher FPF only for particles with 60 and 80% coat levels. Reduced contact surface area between the drug particle and rougher carrier particle resulted in easier drug detachment during aerosolization. The 5 µm micronized lactose produced optimal carrier particles with respect to FPF and surface roughness. The study highlighted that with the ideal particles for surface roughening and coating level, surface roughening could be efficiently achieved by fluid bed coating for superior DPI performance.

Scientific and regulatory activities initiated by the U.S. Food and drug administration to foster approvals of generic dry powder inhalers: Bioequivalence perspective

Regulatory science for generic dry powder inhalers (DPIs) in the United States (U.S.) has evolved over the last decade. In 2013, the U.S. Food and Drug Administration (FDA) published the draft product-specific guidance (PSG) for fluticasone propionate and salmeterol xinafoate inhalation powder. This was the first PSG for a DPI available in the U.S., which provided details on a weight-of-evidence approach for establishing bioequivalence (BE). A variety of research activities including in vivo and in vitro studies were used to support these recommendations, which have led to the first approval of a generic DPI in the U.S. for fluticasone propionate and salmeterol xinafoate inhalation powder in January of 2019. This review describes the scientific and regulatory activities that have been initiated by FDA to support the current BE recommendations for DPIs that led to the first generic DPI approvals, as well as research with novel in vitro and in silico methods that may potentially facilitate generic DPI development and approval.

Generic dry powder inhalers bioequivalence: Batch-to-batch variability insights

Active pharmaceutical ingredient(s) [API(s)] of dry powder inhalers (DPIs) deposition and their fate in the respiratory system are influenced by a complex matrix of formulation, device, manufacturing and physiological variations. DPIs on the market have shown bioinequivalence between batches of the same product. Despite being clinically insignificant, they affect bioequivalence studies when a generic product is compared with the originator. This review discusses implications of batch-to-batch variability on bioequivalence study outcomes and shortcomings of current regulatory requirements. Possible formulation and manufacturing factors resulting in batch-to-batch variability highlight the inherent nature of this issue. Despite scholarly investigations and official regulatory guidance, there remains a need for reliable and realistic in vitro tests that accurately guide a representative reference product batch selection.

Recent developments in lactose blend formulations for carrier-based dry powder inhalation

Lactose is the most commonly used excipient in carrier-based dry powder inhalation (DPI) formulations. Numerous inhalation therapies have been developed using lactose as a carrier material. Several theories have described the role of carriers in DPI formulations. Although these theories are valuable, each DPI formulation is unique and are not described by any single theory. For each new formulation, a specific development trajectory is required, and the versatility of lactose can be exploited to optimize each formulation. In this review, recent developments in lactose-based DPI formulations are discussed. The effects of varying the material properties of lactose carrier particles, such as particle size, shape, and morphology are reviewed. Owing to the complex interactions between the particles in a formulation, processing adhesive mixtures of lactose with the active ingredient is crucial. Therefore, blending and filling processes for DPI formulations are also reviewed. While the role of ternary agents, such as magnesium stearate, has increased, lactose remains the excipient of choice in carrier-based DPI formulations. Therefore, new developments in lactose-based DPI formulations are crucial in the optimization of inhalable medicine performance.

Probing Critical Physical Properties of Lactose-Polyethylene Glycol Microparticles in Pulmonary Delivery of Chitosan Nanoparticles

Pulmonary delivery of chitosan nanoparticles is met with nanoparticle agglomeration and exhalation. Admixing lactose-based microparticles (surface area-weighted diameter~5 μm) with nanoparticles mutually reduces particle agglomeration through surface adsorption phenomenon. Lactose-polyethylene glycol (PEG) microparticles with different sizes, morphologies and crystallinities were prepared by a spray drying method using varying PEG molecular weights and ethanol contents. The chitosan nanoparticles were similarly prepared. In vitro inhalation performance and peripheral lung deposition of chitosan nanoparticles were enhanced through co-blending with larger lactose-PEG microparticles with reduced specific surface area. These microparticles had reduced inter-microparticle interaction, thereby promoting microparticle–nanoparticle interaction and facilitating nanoparticles flow into peripheral lung.

Inhaled antibiotic-loaded polymeric nanoparticles for the management of lower respiratory tract infections

Lower respiratory tract infections (LRTIs) are one of the leading causes of deaths in the world. Currently available treatment for this disease is with high doses of antibiotics which need to be administered frequently. Instead, pulmonary delivery of drugs has been considered as one of the most efficient routes of drug delivery to the targeted areas as it provides rapid onset of action, direct deposition of drugs into the lungs, and better therapeutic effects at low doses and is self-administrable by the patients. Thus, there is a need for scientists to design more convenient pulmonary drug delivery systems towards the innovation of a novel treatment system for LRTIs. Drug-encapsulating polymer nanoparticles have been investigated for lung delivery which could significantly reduce the limitations of the currently available treatment system for LRTIs. However, the selection of an appropriate polymer carrier for the drugs is a critical issue for the successful formulations of inhalable nanoparticles. In this review, the current understanding of LRTIs, management systems for this disease and their limitations, pulmonary drug delivery systems and the challenges of drug delivery through the pulmonary route are discussed. Drug-encapsulating polymer nanoparticles for lung delivery, antibiotics used in pulmonary delivery and drug encapsulation techniques have also been reviewed. A strong emphasis is placed on the impact of drug delivery into the infected lungs.

Puerarin dry powder inhaler formulations for pulmonary delivery: Development and characterization

This study aims at developing and characterizing the puerarin dry powder inhaler (DPI) formulations for pulmonary delivery. The inhalable particles size (<2 μm) was accomplished by micronization and its morphology was examined by scanning electron microscopy (SEM). The puerarin-excipient interaction in powder mixtures was analyzed by using Fourier transform infrared spectroscopy (FTIR), Raman confocal microscopy, X-Ray powder Diffraction (XRD), and differential scanning calorimetry (DSC) methods. Using a Twin stage impinger (TSI), the in-vitro aerosolization of the powder formulations was carried out at a flow rate of 60 L/min and the drug was quantified by employing a validated HPLC method. No significant interactions between the drug and the excipients were observed in the powder formulations. The fine particle fraction (FPF) of the drug alone was 4.2% which has increased five to six-fold for the formulations with aerosolization enhancers. Formulation containing lactose as large carriers produced 32.7% FPF, which further increased with the addition of dispersibility enhancers, leucine and magnesium stearate (40.8% and 41.2%, respectively). The Raman and FTIR techniques are very useful tool for understanding structural integrity and stability of the puerarin in the powder formulations. The puerarin was found to be compatible with the excipients used and the developed DPI formulation may be considered as an efficient formulation for pulmonary delivery for the management of various diseases at a very low dose.

Inhaled RNA Therapeutics for Obstructive Airway Diseases: Recent Advances and Future Prospects

Obstructive airway diseases, e.g., chronic obstructive pulmonary disease (COPD) and asthma, represent leading causes of morbidity and mortality worldwide. However, the efficacy of currently available inhaled therapeutics is not sufficient for arresting disease progression and decreasing mortality, hence providing an urgent need for development of novel therapeutics. Local delivery to the airways via inhalation is promising for novel drugs, because it allows for delivery directly to the target site of action and minimizes systemic drug exposure. In addition, novel drug modalities like RNA therapeutics provide entirely new opportunities for highly specific treatment of airway diseases. Here, we review state of the art of conventional inhaled drugs used for the treatment of COPD and asthma with focus on quality attributes of inhaled medicines, and we outline the therapeutic potential and safety of novel drugs. Subsequently, we present recent advances in manufacturing of thermostable solid dosage forms for pulmonary administration, important quality attributes of inhalable dry powder formulations, and obstacles for the translation of inhalable solid dosage forms to the clinic. Delivery challenges for inhaled RNA therapeutics and delivery technologies used to overcome them are also discussed. Finally, we present future prospects of novel inhaled RNA-based therapeutics for treatment of obstructive airways diseases, and highlight major knowledge gaps, which require further investigation to advance RNA-based medicine towards the bedside.

Dry Powder for Pulmonary Delivery: A Comprehensive Review

The pulmonary route has long been used for drug administration for both local and systemic treatment. It possesses several advantages, which can be categorized into physiological, i.e., large surface area, thin epithelial membrane, highly vascularized, limited enzymatic activity, and patient convenience, i.e., non-invasive, self-administration over oral and systemic routes of drug administration. However, the formulation of dry powder for pulmonary delivery is often challenging due to restrictions on aerodynamic size and the lung’s lower tolerance capacity in comparison with an oral route of drug administration. Various physicochemical properties of dry powder play a major role in the aerosolization, deposition, and clearance along the respiratory tract. To prepare suitable particles with optimal physicochemical properties for inhalation, various manufacturing methods have been established. The most frequently used industrial methods are milling and spray-drying, while several other alternative methods such as spray-freeze-drying, supercritical fluid, non-wetting templates, inkjet-printing, thin-film freezing, and hot-melt extrusion methods are also utilized. The aim of this review is to provide an overview of the respiratory tract structure, particle deposition patterns, and possible drug-clearance mechanisms from the lungs. This review also includes the physicochemical properties of dry powder, various techniques used for the preparation of dry powders, and factors affecting the clinical efficacy, as well as various challenges that need to be addressed in the future.

A review on chitosan and its development as pulmonary particulate anti-infective and anti-cancer drug carriers

Chitosan, as a biodegradable and biocompatible polymer, is characterized by anti-microbial and anti-cancer properties. It lately has received a widespread interest for use as the pulmonary particulate backbone materials of drug carrier for the treatment of infectious disease and cancer. The success of chitosan as pulmonary particulate drug carrier is a critical interplay of their mucoadhesive, permeation enhancement and site/cell-specific attributes. In the case of nanocarriers, various microencapsulation and micro-nano blending systems have been devised to equip them with an appropriate aerodynamic character to enable efficient pulmonary aerosolization and inhalation. The late COVID-19 infection is met with acute respiratory distress syndrome and cancer. Chitosan and its derivatives are found useful in combating HCoV and cancer as a function of their molecular weight, substituent type and its degree of substitution. The interest in chitosan is expected to rise in the next decade from the perspectives of drug delivery in combination with its therapeutic performance.

Numerical Study on Particle Adhesion in Dry Powder Inhaler Device

This study investigated the particle adhesion mechanism in a capsule of dry powder inhaler (DPI) based on a combined computational fluid dynamics and discrete element method (CFD-DEM) approach. In this study, the Johnson-Kendall-Roberts (JKR) theory was selected as the adhesion force model. The simulation results corroborated the experimental results-numerous particles remained on the outlet side of the capsule, while a few particles remained on the inlet side. In the computer simulation, the modeled particles were placed in a capsule. They were quickly dispersed to both sides of the capsule, by air fed from one side of the capsule, and delivered from the air inlet side to the outlet side of the capsule. It was confirmed that vortex flows were seen at the outlet side of the capsule, which, however, were not seen at the inlet side. Numerous collisions were observed at the outlet side, while very few collisions were observed at the inlet side. These results suggested that the vortex flows were crucial to reduce the amount of residual particles in the capsule. The original capsule was then modified to enhance the vortex flow in the area, where many particles were found remaining. The modified capsule reduced the number of residual particles compared to the original capsule. This investigation suggests that the CFD-DEM approach can be a great tool for understanding the particle adhesion mechanism and improving the delivery efficiency of DPIs.

In Silico Optimization of Fiber-Shaped Aerosols in Inhalation Therapy for Augmented Targeting and Deposition across the Respiratory Tract

Motivated by a desire to uncover new opportunities for designing the size and shape of fiber-shaped aerosols towards improved pulmonary drug delivery deposition outcomes, we explore the transport and deposition characteristics of fibers under physiologically inspired inhalation conditions in silico, mimicking a dry powder inhaler (DPI) maneuver in adult lung models. Here, using computational fluid dynamics (CFD) simulations, we resolve the transient translational and rotational motion of inhaled micron-sized ellipsoid particles under the influence of aerodynamic (i.e., drag, lift) and gravitational forces in a respiratory tract model spanning the first seven bifurcating generations (i.e., from the mouth to upper airways), coupled to a more distal airway model representing nine generations of the mid-bronchial tree. Aerosol deposition efficiencies are quantified as a function of the equivalent diameter (dp) and geometrical aspect ratio (AR), and these are compared to outcomes with traditional spherical particles of equivalent mass. Our results help elucidate how deposition patterns are intimately coupled to dp and AR, whereby high AR fibers in the narrow range of dp = 6-7 µm yield the highest deposition efficiency for targeting the upper- and mid-bronchi, whereas fibers in the range of dp= 4-6 µm are anticipated to cross through the conducting regions and reach the deeper lung regions. Our efforts underscore previously uncovered opportunities to design the shape and size of fiber-like aerosols towards targeted pulmonary drug delivery with increased deposition efficiencies, in particular by leveraging their large payloads for deep lung deposition.

Novel drug delivery systems and significance in respiratory diseases

Pulmonary drug delivery offers targeted therapy for the treatment of respiratory diseases such as asthma, lung cancer, and chronic obstructive pulmonary diseases. However, this route poses challenges like deposition mechanism, drug instability, and rapid clearance mechanism. Other factors like the type of inhaler device, patient compatibility, consistent delivery by device, and inhaler technique also affect the performance of pulmonary delivery systems. Thus, to overcome these issues, pulmonary delivery systems utilizing particle-based approaches (nano/microparticles) have emerged in the last two decades. This chapter provides insight into various mechanisms of pulmonary drug administration, the ideal requirements of a pulmonary system, and the general devices used for pulmonary delivery. An overview of new pulmonary delivery systems and their relevance in the treatment of respiratory diseases is provided. In the end, novel pulmonary technologies that have been patented and cleared clinical trials have been highlighted along with the advances in the inhaler device.

Effect of Lactose Pseudopolymorphic Transition on the Aerosolization Performance of Drug/Carrier Mixtures

Physico-chemical properties of lactose are key factors in adhesive mixtures used as dry powder inhaler (DPI). Despite the abundant literature on this topic, the effect of the polymorphism and pseudo-polymorphism of lactose has been seldom investigated and discussed although often lactose used in DPI is subjected to unit operations, which may alter its solid-state properties. Here, we studied the aerosolization performance of salbutamol sulphate (SS) or budesonide (BUD) formulations by investigating the effect of lactose pseudopolymorphism in ternary (coarse lactose/fine lactose/drug) and binary (coarse lactose/drug) mixtures. An improvement of the aerosolization performance of SS formulations with the increase of the amount of fine micronized lactose up to 30% (fine particle fraction (FPF) = 57%) was observed. Micronized lactose contained hygroscopic anhydrous α-lactose, which converted to α-lactose monohydrate at ambient conditions. This implied that the positive effect of fines on the aerosolization performance decreased and eventually disappeared with the formulation aging. Positive effect on SS deposition was observed also with binary mixtures with anhydrous lactose, whereas the opposite occurred with budesonide-containing formulations. The collected data demonstrated the crucial role of the carrier crystal form on the positive effect of fines on the deposition.

The Impact of Lipid Corona on Rifampicin Intramacrophagic Transport Using Inhaled Solid Lipid Nanoparticles Surface-Decorated with a Mannosylated Surfactant

The mimicking of physiological conditions is crucial for the success of accurate in vitro studies. For inhaled nanoparticles, which are designed for being deposited on alveolar epithelium and taken up by macrophages, it is relevant to investigate the interactions with pulmonary surfactant lining alveoli. As a matter of fact, the formation of a lipid corona layer around the nanoparticles could modulate the cell internalization and the fate of the transported drugs. Based on this concept, the present research focused on the interactions between pulmonary surfactant and Solid Lipid Nanoparticle assemblies (SLNas), loaded with rifampicin, an anti-tuberculosis drug. SLNas were functionalized with a synthesized mannosylated surfactant, both alone and in a blend with sodium taurocholate, to achieve an active targeting to mannose receptors present on alveolar macrophages (AM). Physico-chemical properties of the mannosylated SLNas satisfied the requirements relative to suitable respirability, drug payload, and AM active targeting. Our studies have shown that a lipid corona is formed around SLNas in the presence of Curosurf, a commercial substitute of the natural pulmonary surfactant. The lipid corona promoted an additional resistance to the drug diffusion for SLNas functionalized with the mannosylated surfactant and this improved drug retention within SLNas before AM phagocytosis takes place. Moreover, lipid corona formation did not modify the role of nanoparticle mannosylation towards the specific receptors on MH-S cell membrane.

Microstructural characterization of carrier-based dry powder inhalation excipients: Insights and guidance

The growing interest in development of dry powder inhalation (DPI) products raises a need for development of standard testing methods and specifications for DPI excipients. The pharmaceutical industry, meanwhile, yet lacks compendial guidance on this topic. Despite of the complexity of interactions taking place in DPI systems and the large number and variety of interplaying factors, understanding of key determinants of performance (critical quality attributes) of DPI excipients have considerably developed over the past years. In light of the current knowledge in this area, this article provides technical guidance and insights on testing and quality control of carrier-based-DPI excipients. These excipients are, typically, blends of coarse, carrier particles and fine, performance-modulating particles. The article explores techniques used for measurement of key microstructural attributes, namely the particle size distribution, the porosity and the particle surface roughness, the particle shape, rheological properties, and the permeability, of these excipients. The technical relevance of each measurement to the functionality of the excipients is critically discussed. In this regard, caveats concerning use of some measurements and data analysis procedures are raised. The guidance lends itself for compendial adoption.

Effect of Roughness on the Dispersion of Dry Powders for Inhalation: a Dynamic Visualization Perspective

Dry powder inhalers have attracted more interest over the years in every aspect related to them. Interestingly, when focusing on the effects of particle morphology of the active or carrier (excipient), it is generally regarded particle size and shape to influence drug availability of aerosolized particles. However, to date, few studies have examined the effect of texture, i.e., roughness, on this relationship. The main objective of the present work is to gain a closer understanding of the influence of carrier morphology on the aerosolization performance of dry powder inhaler formulations. Image analysis and microscopy were used to visualize the aerosolization process. It is considered that the scale of morphological features on the surface of the carrier particles is responsible for the dispersion of the powder formulation, separation of the drug/carrier, and entrainment from a dry powder inhaler. Thus, for this study, the carrier particles of different surface roughness were mixed with micronized salbutamol sulphate. Aerosolization in vitro testing was used to evaluate the performance. The results indicate a connection between the qualitative surface roughness of coarse carriers and aerosolization performance during powder dispersibility. This investigation demonstrated that indeed, powder dispersion, a dynamic process, is influenced by the scale of the carrier morphology.

Newly synthesized surfactants for surface mannosylation of respirable SLN assemblies to target macrophages in tuberculosis therapy

The present study reports about new solid lipid nanoparticle assemblies (SLNas) loaded with rifampicin (RIF) surface-decorated with novel mannose derivatives, designed for anti-tuberculosis (TB) inhaled therapy by dry powder inhaler (DPI). Mannose is considered a relevant ligand to achieve active drug targeting being mannose receptors (MR) overexpressed on membranes of infected alveolar macrophages (AM), which are the preferred site of Mycobacterium tuberculosis. Surface decoration of SLNas was obtained by means of newly synthesized functionalizing compounds used as surfactants in the preparation of carriers. SLNas were fully characterized in vitro determining size, morphology, drug loading, drug release, surface mannosylation, cytotoxicity, macrophage internalization extent and ability to bind MR, and intracellular RIF concentration. Moreover, the influence of these new surface functionalizing agents on SLNas aerodynamic performance was assessed by measuring particle respirability features using next generation impactor. SLNas exhibited suitable drug payload, in vitro release, and more efficient ability to enter macrophages (about 80%) compared to bare RIF (about 20%) and to non-functionalized SLNas (about 40%). The involvement of MR-specific binding has been demonstrated by saturating MR of J774 cells causing a decrease of RIF intracellular concentration of about 40%. Furthermore, it is noteworthy that the surface decoration of particles produced a poor cohesive powder with an adequate respirability (fine particle fraction ranging from about 30 to 50%). Therefore, the proposed SLNas may represent an encouraging opportunity in a perspective of an efficacious anti-TB inhaled therapy.

Delivery of Dry Powders to the Lungs: Influence of Particle Attributes from a Biological and Technological Point of View

Dry powder inhalers are medical devices used to deliver powder formulations of active pharmaceutical ingredients via oral inhalation to the lungs. Drug particles, from a biological perspective, should reach the targeted site, dissolve and permeate through the epithelial cell layer in order to deliver a therapeutic effect. However, drug particle attributes that lead to a biological activity are not always consistent with the technical requirements necessary for formulation design. For example, small cohesive drug particles may interact with neighbouring particles, resulting in large aggregates or even agglomerates that show poor flowability, solubility and permeability. To circumvent these hurdles, most dry powder inhalers currently on the market are carrier-based formulations. These formulations comprise drug particles, which are blended with larger carrier particles that need to detach again from the carrier during inhalation. Apart from blending process parameters, inhaler type used and patient's inspiratory force, drug detachment strongly depends on the drug and carrier particle characteristics such as size, shape, solid-state and morphology as well as their interdependency. This review discusses critical particle characteristics. We consider size of the drug (1-5 µm in order to reach the lung), solid-state (crystalline to guarantee stability versus amorphous to improve dissolution), shape (spherical drug particles to avoid macrophage clearance) and surface morphology of the carrier (regular shaped smooth or nano-rough carrier surfaces for improved drug detachment.) that need to be considered in dry powder inhaler development taking into account the lung as biological barrier.

Lung delivery of nanoliposomal salbutamol sulfate dry powder inhalation for facilitated asthma therapy

The motive behind present work was to discover a solution for overcoming the problems allied with a deprived oral bioavailability of salbutamol sulfate (SS) due to its first pass hepatic metabolism, shorter half-life, and systemic toxicity at high doses. Pulmonary delivery provides an alternative route of administration to avoid hepatic metabolism of SS, moreover facilitated diffusion and prolonged retention can be achieved by incorporation into liposomes. Liposomes were prepared by thin film hydration technique using 3² full factorial design and formulation was optimized based on the vesicle size and percent drug entrapment (PDE) of liposomes. Optimized liposomal formulation exhibited an average size of about 167.2 ± 0.170 nm, with 80.68 ± 0.74% drug entrapment, and 9.74 ± 1.10 mV zeta potential. The liposomal dispersion was then spray dried and further characterized for in-vitro aerosol performance using Andersen Cascade Impactor. Optimized liposomal formulation revealed prolonged in-vitro drug release of more than 90% up to 14 h following Higuchi's controlled release model. Thus, the proposed new-fangled liposomal formulation would be a propitious alternative to conventional therapy for efficient and methodical treatment of asthma and alike respiratory ailments.

Effect of USP Induction Ports, Glass Sampling Apparatus, and Inhaler Device Resistance on Aerodynamic Patterns of Fluticasone Propionate-Loaded Engineered Mannitol Microparticles

The present investigation is to study the effect of two different induction ports (IP), i.e., USP IP and USP-modified IP equipped with andersen cascade impactor on in vitro aerodynamic performance along with the impact of USP-modified glass sampling apparatus on delivered dose uniformity of fluticasone propionate (FP) dry powder inhaler (DPI). FP DPI was fabricated by spray drying technique using engineered mannitol microparticles (EMP) with different force controlling agents, i.e., leucine and magnesium stearate. Additionally, commercially available two DPI inhaler devices namely Handihaler® and Breezhaler® were used to aerosolize the FP blends. Spherical smooth surface of EMP showed good powder flow properties and acceptable percentage content uniformity (> 95%). Amounts of FP deposited in cascade assembly using USP-modified IP with the Breezhaler® device was significantly higher (1.32-fold) as compared with the Handihaler® device. Moreover, USP-modified IP showed better deposition as compared with USP IP. Additionally, both inhaler devices showed a satisfactory delivered dose (> 105%) for FP using modified glass sampling apparatus at a flow rate of 60 L/min for 2 s. It was interesting to note that not only formulation properties but also IP geometry and device resistance have significant impact on DPI deposition pattern. This study is a first detailed account of aerodynamic performance of FP using USP-modified IP and USP-modified glass sampling apparatus. Thus, it can be of potential importance for both the academic and industry perspective.

Probing the influence of lactose fines, a USP modified induction port and modified DDU apparatus on the aerodynamic behavior of a fluticasone propionate dry powder inhaler

The objective of the present study is to understand the effects of lactose fines, a USP modified induction port (IP) and USP modified glass sampling apparatus (DDU apparatus) on the aerodynamic behavior of a fluticasone propionate (FP) dry powder inhaler (DPI).

Dosing challenges in respiratory therapies

The pulmonary route of administration has been commonly used for local lung conditions such as asthma and chronic obstructive pulmonary disease (COPD). Recently, with the advent of new technologies available for both formulation and device design, molecules usually delivered at high doses, such as antibiotics and insulin to treat cystic fibrosis (CF) and diabetes, respectively, can now be delivered by inhalation as a dry powder. These molecules are generally delivered in milligrams instead of traditional microgram quantities. High dose delivery is most commonly achieved via dry powder inhalers (DPIs), breath activated devices designed with a formulated powder containing micronized drug with aerodynamic diameters between 1 and 5 µm. The powder formulation may also contain other excipients and/or carrier particles to improve the flowability and aerosol dispersion of the powder. A drawback with high doses is that the formulation contains a great number of fine particles, leading to a greater degree of cohesive forces, producing strongly bound agglomerates. With greater cohesive forces holding fine particles together, higher dispersion forces are needed for efficient de-agglomeration and aerosolisation. This requirement of greater dispersion forces has led to different dry powder formulations and vastly different inhaler designs. The purpose of this review is to evaluate the different formulation types, various DPI devices currently available, and how these affect the aerosolisation process and delivery of high dosed inhalable dry powder formulations to the lungs.

Study of the Emitted Dose After Two Separate Inhalations at Different Inhalation Flow Rates and Volumes and an Assessment of Aerodynamic Characteristics of Indacaterol Onbrez Breezhaler® 150 and 300 μg

Onbrez Breezhaler® is a low-resistance capsule-based device that was developed to deliver indacaterol maleate. The study was designed to investigate the effects of both maximum flow rate (MIF) and inhalation volume (Vin) on the dose emission of indacaterol 150 and 300 μg dose strengths after one and two inhalations using dose unit sampling apparatus (DUSA) as well as to study the aerodynamic characteristics of indacaterol Breezhaler® using the Andersen cascade impactor (ACI) at a different set of MIF and Vin. Indacaterol 150 and 300 μg contain equal amounts of lactose per carrier. However, 150 μg has the smallest carrier size. The particle size distribution (PSD) of indacaterol DPI formulations 150 and 300 μg showed that the density of fine particles increased with the increase of the primary pressure. For both strengths (150 μg and 300 μg), ED1 increased and ED2 decreased when the inhalation flow rate and inhaled volume increased. The reduction in ED1 and subsequent increase in ED2 was such that when the Vin is greater than 1 L, then 60 L/min could be regarded as the minimum MIF. The Breezhaler was effective in producing respirable particles with an MMAD ≤5 μm irrespective of the inhalation flow rate, but the mass fraction of particles with an aerodynamic diameter <3 μm is more pronounced between 60 and 90 L/min. The dose emission of indacaterol was comparable for both dose strengths 150 and 300 μg. These in vitro results suggest that a minimum MIF of 60 L/min is required during routine use of Onbrez Breezhaler®, and confirm the good practice to make two separate inhalations from the same dose.

Nano- and Microstructured model carrier surfaces to alter dry powder inhaler performance

The present study investigates the effect of different carrier surface modifications on the aerosolisation performance and on the effective carrier payload of interactive blends for inhalation. Two different active pharmaceutical ingredients (APIs) were used: Formoterol fumarate dihydrate (FF) and budesonide (BUD). Blends were prepared with glass beads as model carriers which have been subjected to mechanical surface modifications in order to introduce surface roughness via treatment with hydrofluoric acid (HF) and/or milling with tungsten carbide (TC). As far as effective carrier payload, in this study expressed as true surface coverage (TSC), is concerned, surface modification had varying effects on blends containing BUD or FF. Aerodynamic characterisation in vitro showed a significant decrease in respirable fraction for glass beads treated with HF (40.2-50.1%), due to the presence of clefts and cavities, where drug particles were sheltered during inhalation. In contrast, grinding with TC leads to surface roughness on a nano scale, ultimately increasing aerodynamic performance up to 20.0-38.1%. These findings are true for both APIs, regardless of their chemical properties.

The Impact of Inspiratory Flow Rate on Drug Delivery to the Lungs with Dry Powder Inhalers

Current marketed dry powder inhalers utilize the energy from patient inspiration to fluidize and disperse bulk powder agglomerates into respirable particles. Variations in patient inspiratory flow profiles can lead to marked differences in total lung dose (TLD), and ultimately patient outcomes for an inhaled therapeutic. The present review aims to quantitate the flow rate dependence in TLD observed for a number of drug/device combinations using a new metric termed the Q index. With this data in hand, the review explores key attributes in the design of the formulation and device that impact flow rate dependence. The review also proposes alternative in vitro methods to assess flow rate dependence that more closely align with in vivo observations. Finally, the impact of variations in flow rate on lung function for inhaled bronchodilators is summarized.

On the effects of blending, physicochemical properties, and their interactions on the performance of carrier-based dry powders for inhalation - A review

Blending drug and carrier powders to produce homogeneous drug-carrier adhesive mixtures is a key step in the production of dry powder inhaler (DPI) formulations. Although the blending conditions can result in different conclusions or probably change the outcome of a study entirely if being selected differently, there is a scarcity of data on the influence of blending processes on the physicochemical properties of bulk powder formulations and the follow-on effects on DPI performance. This paper provides an overview of the interactions between variables related to blending conditions (e.g. blending equipment, time, speed and sequence as well as environmental humidity) and powder physicochemical properties (e.g. size distribution, shape distribution, density, anomeric composition, electrostatic charge, surface, and bulk properties), and their effects on the performance of adhesive mixtures for inhalation in terms of drug content homogeneity, drug-carrier adhesion, and drug aerosolisation behaviour. The relevance of carrier payload, batch size and segregation was also discussed. Challenges and future directions were identified. This review therefore contributes towards a better understanding of the blending process, powder physicochemical properties, and their interlinked effects on the fundamental understanding of adhesive mixtures for inhalation. The knowledge gained is essential to ensure optimum blending and thereby controlled functionality of DPIs.

Influence of physical properties of carrier on the performance of dry powder inhalers

Dry powder inhalers (DPIs) offer distinct advantages as a means of pulmonary drug delivery and have attracted much attention in the field of pharmaceutical science. DPIs commonly contain micronized drug particles which, because of their cohesiveness and strong propensity to aggregate, have poor aerosolization performance. Thus carriers with a larger particle size are added to address this problem. However, the performance of DPIs is profoundly influenced by the physical properties of the carrier, particularly their particle size, morphology/shape and surface roughness. Because these factors are interdependent, it is difficult to completely understand how they individually influence DPI performance. The purpose of this review is to summarize and illuminate how these factors affect drug–carrier interaction and influence the performance of DPIs.