Progress of Photoelectrochemical Analysis and Sensors

Molecularly imprinted photoelectrochemical sensor for ultrasensitive and selective detection of hydroquinone using 0D CdS nanoparticle/3D flower-like ZnIn2S4 microsphere nanocomposite

A novel photoelectrochemical (PEC) sensor was developed for the ultra-sensitive and highly selective detection of hydroquinone (HQ), featuring a composite structure that combines 0D CdS nanoparticles with a 3D flower-like ZnIn2S4 microsphere. The sensor, termed rMIP/CdS/ZnIn2S4, employed molecularly imprinted polymers (MIPs) to achieve specific recognition of HQ. An p-phenylenediamine (pPD) polymer film was electrochemically polymerized onto the surface of the CdS/ZnIn2S4 composite-coated glassy carbon electrode (GCE). Through hydrogen bonding, HQ molecules were imprinted onto the polymer film. Subsequent elution removed these molecules, leaving behind specific recognition sites, enabling selective detection of HQ. The unique spatial structure and heterojunction properties of the 0D CdS nanoparticle/3D flower-like ZnIn2S4 composite, combined with molecular imprinting, significantly enhanced the photocurrent response and increased the selectivity and sensitivity for HQ detection. Under optimal conditions, the rMIP/CdS/ZnIn2S4 sensor demonstrated a low detection limit (0.7 nmol·L-1, S/N=3) over a wide linear range of 1-1200 nmol·L-1. The sensor was successfully applied to detect HQ in real water samples, showing promise for environmental pollution control applications.

Development of novel nanocomposite-modified photoelectrochemical sensor based on the association of bismuth vanadate and MWCNT-grafted-molecularly imprinted poly(acrylic acid) for dopamine determination at nanomolar level

This study proposes the development of a new photoelectrochemical (PEC) sensor for the determination of dopamine (DA) at nanomolar levels. The PEC sensor was based on a physical mixture of bismuth vanadate (BiVO4) with nanocomposite molecularly imprinted poly(acrylic acid) (MIP-AA) grafted onto MWCNTox by using the surface-controlled radical polymerization strategy with an INIFERTER reagent. XRD, diffuse reflectance spectroscopy (DRE), SEM, TEM, and TGA were employed to characterize the materials. Photoelectrochemical analyses were carried out with GCE/BiVO4/MIP-AA sensor under visible light using a potential of 0.6 V, phosphate buffer (0.1 mol L-1) at pH 7.0, and modifying the GCE with a film composed of monoclinic BiVO4 at 3.5 mg mL-1 and nanocomposite MIP prepared with acrylic acid (MIP-AA) at 0.1 mg mL-1. The proposed method using the GCE/BiVO4/MIP-AA sensor presented a limit of detection (LOD) of 2.9 nmol L-1, a linear range from 9.7 to 150 nmol L-1 and it was successfully applied for analysis of DA in urine samples using external calibration curve yielding recovery values of 90-105%. Additionally, the proposed PEC sensor allowed DA determination without interference from uric acid, ascorbic acid, epinephrine, norepinephrine, and other unwanted interferences.

Photoelectrochemical Enzyme Biosensor for Malate Using Quantum Dots on Indium Tin Oxide/Plastics as a Sensing Surface

A photoelectrochemical biosensor for malate was developed using an indium tin oxide (ITO) layer deposited on a poly(ethylene terephthalate) plastic sheet as a transparent electrode material for the immobilization of malate dehydrogenase together with CdTe quantum dots. Different approaches were compared for the construction of the bioactive layer; the highest response was achieved by depositing malate dehydrogenase together with CdTe nanoparticles and covering it with a Nafion/water (1:1) mixture. The amperometric signal of this biosensor was recorded during irradiation with a near-UV LED in the flow-through mode. The limit of detection was 0.28 mmol/L, which is adequate for analyzing malic acid levels in drinks such as white wines and fruit juices. The results confirm that the cheap ITO layer deposited on the plastic sheet after cutting into rectangular electrodes allows for the economic production of photoelectrochemical (bio)sensors. The combination of NAD+-dependent malate dehydrogenase with quantum dots was also compatible with such an ITO surface.

Semiconductor quantum dots in photoelectrochemical sensors from fabrication to biosensing applications

Semiconductor quantum dots (QDs) are a promising class of nanomaterials for developing new photoelectrodes and photoelectrochemistry systems for energy storage, transfer, and biosensing applications. These materials have unique electronic and photophysical properties and can be used as optical nanoprobes in displays, biosensors, imaging, optoelectronics, energy storage and energy harvesting. Researchers have recently been exploring the use of QDs in photoelectrochemical (PEC) sensors, which involve exciting a QD-interfaced photoactive material with a flashlight source and generating a photoelectrical current as an output signal. The simple surface properties of QDs also make them suitable for addressing issues related to sensitivity, miniaturization, and cost-effectiveness. This technology has the potential to replace current laboratory practices and equipment, such as spectrophotometers, used for testing sample absorption and emission. Semiconductor QD-based PEC sensors offer simple, fast, and easily miniaturized sensors for analyzing a variety of analytes. This review summarizes the various strategies for interfacing QD nanoarchitectures for PEC sensing, as well as their signal amplification. PEC sensing devices, particularly those used for the detection of disease biomarkers, biomolecules (glucose, dopamine), drugs, and various pathogens, have the potential to revolutionize the biomedical field. This review discusses the advantages of semiconductor QD-based PEC biosensors and their fabrication methods, with a focus on disease diagnostics and the detection of various biomolecules. Finally, the review provides prospects and considerations for QD-based photoelectrochemical sensor systems in terms of their sensitivity, speed, and portability for biomedical applications.

Ecological effects, remediation, distribution, and sensing techniques of chromium

Chromium is detected in most ecosystems due to the increased anthropogenic activities in addition to that developed from natural pollution. Chromium contamination in the food chain results due to its persistent and non-degradable nature. The release of chromium in the ecosystem accretes and thereafter impacts different life forms, including humans, aquatic and terrestrial organisms. Leaching of chromium into the ground and surface water triggers several health ailments, such as dermatitis, eczematous skin, allergic reactions, mucous and skin membrane ulcerations, allergic asthmatic reactions, bronchial carcinoma and gastroenteritis. Physiological and biological treatments for the removal of chromium have been discussed in depth in the present communication. Adsorption and biological treatment methods are proven to be alternatives to chemical removal techniques in terms of cost-effectiveness and low sludge formation. Chromium sensing is an alternative approach for regular monitoring of chromium in different water bodies. This review intended to explore different classes of sensors for chromium monitoring. However, the spectrochemical methods are more sensitive in chromium ions sensing than electrochemical methods. Future study should focus on miniaturization for portability and on-site measurements without requiring a large instrument provides a good aspect for future research.

A novel photoelectrochemical immunosensor based on TiO2@Bi2WO6 hollow microspheres and Ag2S for sensitive detection of SARS-COV-2 nucleocapsid protein

Severe Acute Respiratory Syndrome Coronavirus 2 (SARS-COV-2) is a cluster of β coronaviruses. The 2019 coronavirus disease (COVID-19) caused by SARS-COV-2 is emerging as a global pandemic. Thus, early diagnosis of SARS-COV-2 is essential to prevent severe outbreaks of the disease. In this experiment, a novel label-free photoelectrochemical (PEC) immunosensor was obtained based on silver sulfide (Ag2S) sensitized titanium dioxide@bismuth tungstate (TiO2@Bi2WO6) nanocomposite for quantitative detection of SARS-COV-2 nucleocapsid protein. The constructed TiO2@Bi2WO6 hollow microspheres had large specific surface area and could produce high photocurrent intensity under visible light illumination. Ag2S was in-situ grown on the surface of thioglycolic acid (TGA) modified TiO2@Bi2WO6. In particular, TiO2@Bi2WO6 and Ag2S formed a good energy level match, which could effectively enhance the photocurrent conversion efficiency and strength the photocurrent response. Ascorbic acid (AA) acted as an effective electron donor to effectively eliminate photogenerated holes. Under optimal experimental conditions, the constructed immunosensor presented a supersensitive response to SARS-COV-2 nucleocapsid protein, with a desirable linear relationship ranged from 0.001 to 50 ng/mL for nucleocapsid protein and a lower detection limit of 0.38 pg/mL. The fabricated sensor exhibited a wide linear range, excellent selectivity, specificity and stability, which provided a valuable referential idea for the detection of SARS-COV-2.

Cuprous oxide coated silver/graphitic carbon nitride/cadmium sulfide nanocomposite heterostructure: Specific recognition of carcinoembryonic antigen through sandwich-type mechanism

The development of the effective diagnostic method for the determination of cancer biomarkers is one of the most promising strategies for early clinical diagnosis of cancer. Here, based on the preparation of heterogeneous cuprous oxide coated silver (Ag@Cu₂O) nanocomposites/graphitic carbon nitride (g-C₃N₄)/cadmium sulfide (CdS) nanoarrays structure, a highly sensitive photoelectrochemical (PEC) biosensor for the examination of carcinoembryonic antigen (CEA) has been constructed successfully. The combination of photoactive semiconductor materials g-C₃N₄ and CdS increases the electron transfer rate between them and enhances their photocurrent response, thus greatly increasing the concentration detection range. At the same time, the specific recognition between antigen and antibody is used to form a sandwich structure secondary antibody (Ab₂)/CEA/antibody (Ab₁). And because Ag@Cu₂O has the function of absorbing light and consuming electron donor. Therefore, the successful measurement of CEA was achieved by labeling Ag@Cu₂O on Ab₂ and finally immobilizing it on the sensor to correlate the current reduction with the CEA concentration. The sandwich PEC biosensor proposed by this signal amplification strategy under optimal conditions has good analytical performance for CEA, with a wide linear detection range (from 10^-5 to 1 ng/mL) and a low detection limit of 0.0011 pg/mL. The PEC biosensor constructed by this method showed high sensitivity, excellent anti-interference ability, favourable repeatability, and good stability.

Photoelectrochemical aptasensors for detection of viruses

Photoelectrochemistry (PEC) is a dynamic discipline studying the effect of light on photoelectrode or photosensitive material, and the conversion from solar energy into electrical power. The basic PEC process refers to the oxidation or reduction reactions between electrochemical active species in solution and photoactive materials that occurred at the electrode/electrolyte interface during illumination. In recent years, the PEC biosensing approaches have also been developed by the combination of the PEC technique with bioanalysis, where the interaction between biological recognition element and analyte influences a photocurrent signal. This involves the charge and energy transfer of PEC reaction between electron donor/acceptor and photoactive material upon light irradiation. Coupling the advantages of PEC bioanalysis and aptamers has provided new concepts for highly selective and sensitive biosensors development, applicable in human health monitoring and environmental protection. In a typical assay, a photoactive material converts the affinity binding properties of aptamers into a detectable electrical signal, presenting an innovative method for probing numerous aptamer-analyte interactions. Using different aptamer probes aiming for specific purposes, more sensing strategies with rational design and exquisite signaling mechanisms have been proposed. This review concentrated on the current topic of PEC aptasensors that are used for the detection of viruses. The prospects in this area are also discussed.

Graphical abstract

Carbon Nanomaterial-Based Drug Sensing Platforms Using State-of-the- Art Electroanalytical Techniques

Background:

Currently, nanotechnology and nanomaterials are considered as the most popular and outstanding research subjects in scientific fields ranging from environmental studies to drug analysis. Carbon nanomaterials such as carbon nanotubes, graphene, carbon nanofibers etc. and non-carbon nanomaterials such as quantum dots, metal nanoparticles, nanorods etc. are widely used in electrochemical drug analysis for sensor development. Main aim of drug analysis with sensors is developing fast, easy to use and sensitive methods. Electroanalytical techniques such as voltammetry, potentiometry, amperometry etc. which measure electrical parameters such as current or potential in an electrochemical cell are considered economical, highly sensitive and versatile techniques.

Methods:

Most recent researches and studies about electrochemical analysis of drugs with carbon-based nanomaterials were analyzed. Books and review articles about this topic were reviewed.

Results:

The most significant carbon-based nanomaterials and electroanalytical techniques were explained in detail. In addition to this; recent applications of electrochemical techniques with carbon nanomaterials in drug analysis was expressed comprehensively. Recent researches about electrochemical applications of carbon-based nanomaterials in drug sensing were given in a table.

Conclusion:

Nanotechnology provides opportunities to create functional materials, devices and systems using nanomaterials with advantageous features such as high surface area, improved electrode kinetics and higher catalytic activity. Electrochemistry is widely used in drug analysis for pharmaceutical and medical purposes. Carbon nanomaterials based electrochemical sensors are one of the most preferred methods for drug analysis with high sensitivity, low cost and rapid detection.

Coordination-induced structural changes of DNA-based optical and electrochemical sensors for metal ions detection

Metal ions play a critical role in human health and abnormal levels are closely related to various diseases. Therefore, the detection of metal ions with high selectivity, sensitivity and accuracy is particularly important. This article highlights and comments on the coordination-induced structural changes of DNA-based optical, electrochemical and optical-electrochemical-combined sensors for metal ions detection. Challenges and potential solutions of DNA-based sensors for the simultaneous detection of multiple metal ions are also discussed for further development and exploitation.

Photoamperometric flow injection analysis of glucose based on dehydrogenase modified quantum dots-carbon nanotube nanocomposite electrode

In this work, a core-shell quantum dot (QD, ZnS-CdS) was electrodeposited onto multiwalled carbon nanotube modified glassy carbon electrode (ZnS-CdS/MWCNT/GCE) and following glucose dehydrogenase (GDH) was immobilized onto QD modified electrode. The proposed electrode (GDH/ZnS-CdS/MWCNT/GCE) was effectively used for the photoelectrochemical biosensing of glucose in flow injection analysis (FIA) system using a home-made flow cell. Results from cyclic voltammetric and FI amperometric measurements have revealed that GDH/ZnS-CdS/MWCNT/GCE is capable of signaling photoelectrocatalytic activity toward NADH when the surface of enzyme modified electrode was irradiated with a light source (250W Halogen lamp). Thus, photoelectrochemical biosensing of glucose was monitored by recording current-time curve of enzymatically produced NADH at optimized conditions. The biosensor response was found linear over the range 0.010-2.0mM glucose with detection limits of 6.0 and 4.0μM for amperometric and photoamperometric methods, respectively. The relative standard deviations (n=5) for 0.5mM glucose were 5.8% and 3.8% for photoamperometric and amperometric results, respectively. The photoelectrochemical biosensor was successfully applied to the real samples. The results with this biosensor showed good selectivity, repeatability and sensitivity for monitoring glucose in amperometric and photoamperometric FIA studies.

Photoelectrochemical glucose biosensor based on a dehydrogenase enzyme and NAD+/NADH redox couple using a quantum dot modified pencil graphite electrode

A simple, disposable and economical modified electrode was prepared by electrodeposition of hybrid quantum dots onto a pencil graphite electrode surface and immobilization of glucose dehydrogenase onto the quantum dot modified electrode.

A signal "on" photoelectrochemical biosensor for assay of protein kinase activity and its inhibitor based on graphite-like carbon nitride, Phos-tag and alkaline phosphatase

A highly sensitive and selective photoelectrochemical (PEC) biosensor is fabricated for the detection of protein kinase activity based on visible-light active graphite-like carbon nitride (g-C3N4) and the specific recognition utility of Phos-tag for protein kinase A (PKA)-induced phosphopeptides. For assembling the substrate peptides, g-C3N4 and gold nanoparticles (g-C3N4-AuNPs) complex is synthesized and characterized. When the immobilized peptides on g-C3N4-AuNPs modified ITO electrode are phosphorylated under PKA catalysis, they can be specifically identified and binded with biotin functionalized Phos-tag (Phos-tag-biotin) in the presence of Zn(2+). Then, through the specific interaction between biotin and avidin, avidin functionalized alkaline phosphatase (avidin-ALP) is further assembled to catalyze its substrate of l-ascorbic acid-2-phosphate trisodium salt (AAP) to produce electron donor of ascorbic acid (AA), resulting an increased photocurrent compared with the absence of phosphorylation event. Based on the specific identification effect of Phos-tag, the fabricated biosensor presents excellent selectivity for capturing the phosphorylated serine residues in the substrate peptides. With the good photoactivity of g-C3N4 and ALP-catalyzed signal amplification, the fabricated biosensor presents high sensitivity and low detection limit (0.015 unit/mL, S/N = 3) for PKA. The applicability of this PEC biosensor is further testified by the evaluation of PKA inhibition by HA-1077 with the IC50 value of 1.18μM. This new strategy is also successfully applied to detect the change of PKA activity in cancer cell lysate with and without drug stimulation. Therefore, the developed PEC method has great potential in screening of kinase inhibitors and highly sensitive detection of kinase activity.