Breath Figure: A Nature-Inspired Preparation Method for Ordered Porous Films

Morphological advances and innovations in conjugated polymer films for high-performance gas sensors

Conjugated polymers (CPs) are considered one of the most important gas-sensing materials due to their unique features, combining the benefits of both metals and semiconductors, along with their outstanding mechanical properties and excellent processability. However, CPs with conventional morphological structures, such as largely amorphous and bulky matrices, face limitations in practical applications because of their inferior charge transport characteristics, low surface area, and insufficient sensitivity. Therefore, the design and development of novel morphological nanostructures in CPs have attracted significant attention as a promising strategy for improving morphological and electrical characteristics, thereby enabling a considerable increase in the sensing performance of corresponding gas sensors. Numerous CP nanostructures have been developed and implemented for high-performance gas sensors. Highlighting the morphological advances and bottlenecks of these nanostructures is crucial for providing an overview of developing trends, potential strategies, and emerging areas for the future development of CP nanostructures in the field. In this regard, this study describes state-of-the-art CP nanostructures, emphasizing their attractive morphological and electrical characteristics to help readers and researchers better understand emerging trends, promising future directions, and key obstacles for the application of CP nanostructure-based gas sensors. The most crucial aspects of CP nanostructures, including advanced preparation techniques, morphological properties, and sensing characteristics, are discussed and assessed in detail. Moreover, development strategies and perspectives for achieving high sensing efficiency in CP nanostructure-based flexible and wearable sensors are summarized and emphasized.

Hierarchically Porous Wearable Composites for High-Performance Stretchable Supercapacitors

With the rapid development of wearable electronic devices, the demand for flexible, durable, and high-performance energy storage systems has increased significantly. Nevertheless, maintaining stable electrochemical performance during stretching while ensuring high stretchability and mechanical stability remains a challenge. Herein, this study proposes a novel type of stretchable supercapacitors made from carbon nanotube (CNT) and styrene-butadiene-styrene (SBS) composite scaffolds prepared on pre-stretched carbon fabrics using the breath figure method. Hydrothermal treatment is then performed to grow NiCo-LDH at the treated carbon fabrics. This method induces the formation of a hierarchically porous structure under high humidity conditions, controls the hydrothermal growth of NiCo-LDH in the CNT/SBS composite scaffold, and significantly enhances the electrochemical performance and mechanical stability. The supercapacitor demonstrates remarkable retention of 94% capacitance under 80% tensile strain and sustains a small 8% degradation over 20 000 charge-discharge cycles, achieving a specific capacitance of 4948 mF cm⁻2 at 2 mA cm⁻2. The device has an energy density of 801.6 µWh cm⁻2 (400.6 Wh kg⁻¹) and exhibits excellent performance at a power density of 3.5 mW cm⁻2 (1749.5 W kg⁻¹). These properties make the supercapacitors a potential for next-generation smart wearables and wearable electronics.

Ultra-Flexible Pixelated Perovskite Photodetectors Enabled by Honeycomb Polymer Grids for High-Resolution Imaging

A nature-inspired fabrication method based on a photolithography-free flexible polymer grid is reported for high-resolution pixelation of perovskite photodiode arrays with exceptional mechanical ductility and a morphology resembling that of natural compound eyes. The resulting pixelated perovskite photosensitive layer has a ≈1 µm pixel size with 2000 Pixels per inch (PPI) resolution when fully assembled as a photodetector array, delivering a detectivity of >1013 Jones while providing cross-talk free imaging. Using a polymer grid effectively releases stress on the perovskite platform, greatly increasing the mechanical agility of the otherwise brittle perovskite film. This novel fabrication methodology and device design offer new possibilities for applications in robotics, biomedical imaging, and virtual and augmented reality.

Water Droplet Templating Technique to Design Three-Dimensionally Ordered Porous Structures of Polymer Film

We developed a unique water droplet templating method to fabricate polymer films with three-dimensionally ordered porous structures. This technique is based on a polymer/solvent/H2O ternary system, and the key is to choose a volatile and hydrophobic solvent that is slightly miscible with H2O. With the fast evaporation of the solvent, water droplets separate from the casting solution and condense from the air to act as pore templates inside the film and on the surface, respectively. According to this law, nitrocellulose (NC) films were produced from the NC/methyl acetate (MA)/H2O system in which the solubility of H2O in MA is 8.1 wt %. By modulating the solution concentration (density) from 3% to 9% NC, the distribution of separated water droplets (pores) in the solution can be flexibly controlled from sinking to floating. On the other hand, substantial ordered honeycomb pores, originated from condensed water droplets, distribute uniformly on the surface of NC films. This water droplet templating technique can be extensively applied in various polymer films, providing an effective pathway to designing polymer films with a desirable porous structure and diverse functionalities.

High Performance Organic Mixed Ionic-Electronic Polymeric Conductor with Stability to Autoclave Sterilization

We present a series of newly developed donor-acceptor (D-A) polymers designed specifically for organic electrochemical transistors (OECTs) synthesized by a straightforward route. All polymers exhibited accumulation mode behavior in OECT devices, and tuning of the donor comonomer resulted in a three-order-of-magnitude increase in transconductance. The best polymer gFBT-g2T, exhibited normalized peak transconductance (gm,norm) of 298±10.4 S cm-1 with a corresponding product of charge-carrier mobility and volumetric capacitance, μC*, of 847 F V-1 cm-1 s-1 and a μ of 5.76 cm2 V-1 s-1, amongst the highest reported to date. Furthermore, gFBT-g2T exhibited exceptional temperature stability, maintaining the outstanding electrochemical performance even after undergoing a standard (autoclave) high pressure steam sterilization procedure. Steam treatment was also found to promote film porosity, with the formation of circular 200-400 nm voids. These results demonstrate the potential of gFBT-g2T in p-type accumulation mode OECTs, and pave the way for the use in implantable bioelectronics for medical applications.

Friction-reduction effect of the hierarchical surface microstructure of carrion beetle by controlling the real contact area

The discovery and elucidation of the surface microstructure functions of living organisms are crucial to resolving issues, such as friction. We newly discovered that Necrophila japonica, a type of carrion beetle that lives on the ground surface, exhibited a hierarchical surface microstructure comprising a submicron-sized wrinkle structure on top of a micron-sized microstructure. The surface microstructure of this beetle improved wettability but did not exhibit superhydrophobicity, a well-known function of hierarchical structures, so it was expected to have a different function. By combining the insights in the field of structural mechanics that avoidance of stress concentration by the structural geometry affects deformation with the basic principles of friction, the frictional properties and mechanisms of the hierarchical surface microstructure of carrion beetle were investigated. The measurements of frictional force indicated that the mimicked structure exerted lower frictional forces than flat and single-layer microstructure surfaces. Analysis of finite element method simulations showed that even though the mimicked structure was prone to pressure concentration due to small contact points, the surface contact pressure was reduced more than that of the single-layer structure by hierarchical load dispersion like that of metamaterials. As a result, the suppression of the increase in the real contact area due to deformation suppression contributed to effective friction-reduction. The effective friction-reduction by the hierarchical structure provides not only new insight into the surface microstructure function of various organisms, but also new design for the lubricant-free friction reduction that has been the focus of attention in carbon neutrality and other fields.

Effect of Grafting Density on the Crystallization Behavior of Molecular Bottlebrushes

A unique case of sterically constrained crystallization arises in bottlebrush polymers bearing semicrystalline side chains. Bottlebrushes with grafted side chains can form crystalline structures governed by the complex interplay between side chain packing and backbone confinement. The confinement effect can be readily tuned by varying the side chain grafting density, thus affording control over the crystallization behavior of these systems. In this work, the grafting density effect on the crystallization behavior of molecular bottlebrushes comprising poly(ethylene oxide) (PEO) side chains grafted to a methacrylate backbone was systematically studied. Thermal analysis using differential scanning calorimetry showed that the bottlebrush polymers displayed suppressed crystallization temperatures, lower melting temperatures, and reduced crystallinities compared to linear homopolymer PEO. The crystalline morphology was investigated using polarized light, atomic force, and scanning electron microscopy. Isothermal crystallization experiments revealed a nonmonotonous dependence of the nucleation density on the side chain grafting density. The grafting density effect was also investigated using self-seeding experiments, revealing an increased clearing temperature and memory retention at higher grafting densities. This work highlights how grafting density influences the crystallization behavior of semicrystalline bottlebrushes, providing information for the processing and application of these unique polymers.

Transient Response and Ionic Dynamics in Organic Electrochemical Transistors

The rapid development of organic electrochemical transistors (OECTs) has ushered in a new era in organic electronics, distinguishing itself through its application in a variety of domains, from high-speed logic circuits to sensitive biosensors, and neuromorphic devices like artificial synapses and organic electrochemical random-access memories. Despite recent strides in enhancing OECT performance, driven by the demand for superior transient response capabilities, a comprehensive understanding of the complex interplay between charge and ion transport, alongside electron-ion interactions, as well as the optimization strategies, remains elusive. This review aims to bridge this gap by providing a systematic overview on the fundamental working principles of OECT transient responses, emphasizing advancements in device physics and optimization approaches. We review the critical aspect of transient ion dynamics in both volatile and non-volatile applications, as well as the impact of materials, morphology, device structure strategies on optimizing transient responses. This paper not only offers a detailed overview of the current state of the art, but also identifies promising avenues for future research, aiming to drive future performance advancements in diversified applications.

Earthworm-Inspired Ultra-Durable Sliding Triboelectric Nanogenerator with Bionic Self-Replenishing Lubricating Property for Wind Energy Harvesting and Self-Powered Intelligent Sports Monitoring

Triboelectric nanogenerators (TENGs), a promising strategy for harvesting distributed low-quality power sources, face inevitable bottlenecks regarding long-term abrasion and poor durability. Herein, both issues are addressed by selecting an earthworm-inspired self-replenishing bionic film (ERB) as the tribo-material of sliding-freestanding TENGs (SF-TENGs), it consists of an interconnected 3D porous network structure capable of storing and releasing lubricant under cyclic mechanical stimuli. Thanks to the superiority of self-replenishing property, there is no need for periodic replenishment and accurate content control of lubricant over the interfacial-lubricating SF-TENGs based on dense tribo-layers. Additionally, an SF-TENG based on ERB film (ERB-TENG) demonstrates remarkable output stability with only a slight attenuation of 1% after continuous operation for 100 000 cycles. Moreover, the ERB-TENG displays a distinguished anti-wear property, exhibiting no distinct abrasion with an ultra-low coefficient of friction (0.077) and maintaining output stability over a prolonged period of 35 days. Furthermore, integration with an energy management circuit enables the ERB-TENG to achieve a 39-fold boost in charging speed. This work proposes a creative approach to enhance the durability and extend the lifespan of TENG devices, which is also successfully applied to wind energy harvesting and intelligent sports monitoring.

Bilayer Scaffolds of PLLA/PCL/CAB Ternary Blend Films and Curcumin-Incorporated PLGA Electrospun Nanofibers: The Effects of Polymer Compositions and Solvents on Morphology and Molecular Interactions

Tissue engineering scaffolds have been dedicated to regenerating damaged tissue by serving as host biomaterials for cell adhesion, growth, differentiation, and proliferation to develop new tissue. In this work, the design and fabrication of a biodegradable bilayer scaffold consisting of a ternary PLLA/PCL/CAB blend film layer and a PLGA/curcumin (CC) electrospun fiber layer were studied and discussed in terms of surface morphology, tensile mechanical properties, and molecular interactions. Three different compositions of PLLA/PCL/CAB-60/15/25 (TBF1), 75/10/15 (TBF2), and 85/5/10 (TBF3)-were fabricated using the solvent casting method. The electrospun fibers of PLGA/CC were fabricated using chloroform (CF) and dimethylformamide (DMF) co-solvents in 50:50 and 60:40 volume ratios. Spherical patterns of varying sizes were observed on the surfaces of all blend films-TBF1 (17-21 µm) > TBF2 (5-9 µm) > TBF3 (1-5 µm)-caused by heterogeneous surfaces inducing bubble nucleation. The TBF1, TBF2, and TBF3 films showed tensile elongation at break values of approximately 170%, 94%, and 43%, respectively. The PLGA/CC electrospun fibers fabricated using 50:50 CF:DMF had diameters ranging from 100 to 400 nm, which were larger than those of the PLGA fibers (50-200 nm). In contrast, the PLGA/CC electrospun fibers fabricated using 60:40 CF:DMF had diameters mostly ranging from 200 to 700 nm, which were larger than those of PLGA fibers (200-500 nm). Molecular interactions via hydrogen bonding were observed between PLGA and CC. The surface morphology of the bilayer scaffold demonstrated adhesion between these two solid surfaces resembling "thread stitches" promoted by hydrophobic interactions, hydrogen bonding, and surface roughness.

Recent Developments in Slippery Liquid-Infused Porous Surface Coatings for Biomedical Applications

Slippery liquid-infused porous surface (SLIPS), inspired by the Nepenthes pitcher plant, exhibits excellent performances as it has a smooth surface and extremely low contact angle hysteresis. Biomimetic SLIPS attracts considerable attention from the researchers for different applications in self-cleaning, anti-icing, anticorrosion, antibacteria, antithrombotic, and other fields. Hence, SLIPS has shown promise for applications across both the biomedical and industrial fields. However, the manufacturing of SLIPS with strong bonding ability to different substrates and powerful liquid locking performance remains highly challenging. In this review, a comprehensive overview of research on SLIPS for medical applications is conducted, and the design parameters and common fabrication methods of such surfaces are summarized. The discussion extends to the mechanisms of interaction between microbes, cells, proteins, and the liquid layer, highlighting the typical antifouling applications of SLIPS. Furthermore, it identifies the potential of utilizing the controllable factors provided by SLIPS to develop innovative materials and devices aimed at enhancing human health.

High-throughput fabrication of antimicrobial phage microgels and example applications in food decontamination

Engineered by nature, biological entities are exceptional building blocks for biomaterials. These entities can impart enhanced functionalities on the final material that are otherwise unattainable. However, preserving the bioactive functionalities of these building blocks during the material fabrication process remains a challenge. We describe a high-throughput protocol for the bottom-up self-assembly of highly concentrated phages into microgels while preserving and amplifying their inherent antimicrobial activity and biofunctionality. Each microgel is comprised of half a million cross-linked phages as the sole structural component, self-organized in aligned bundles. We discuss common pitfalls in the preparation procedure and describe optimization processes to ensure the preservation of the biofunctionality of the phage building blocks. This protocol enables the production of an antimicrobial spray containing the manufactured phage microgels, loaded with potent virulent phages that effectively reduced high loads of multidrug-resistant Escherichia coli O157:H7 on red meat and fresh produce. Compared with other microgel preparation methods, our protocol is particularly well suited to biological materials because it is free of organic solvents and heat. Bench-scale preparation of base materials, namely microporous films (the template for casting microgels) and pure concentrated phage suspension, requires 3.5 h and 5 d, respectively. A single production run, that yields over 1,750,000 microgels, ranges from 2 h to 2 d depending on the rate of cross-linking chemistry. We expect that this platform will address bottlenecks associated with shelf-stability, preservation and delivery of phage for antimicrobial applications, expanding the use of phage for prevention and control of bacterial infections and contaminants.

Light-Induced Self-Assembled Polydiacetylene/Carbon Dot Functional "Honeycomb"

The design of functional supramolecular assemblies from individual molecular building blocks is a fundamental challenge in chemistry and material science. We report on the fabrication of "honeycomb" films by light-induced coassembly of diacetylene derivatives and carbon dots. Specifically, modulating noncovalent interactions between the carbon dots, macrocyclic diacetylene, and anthraquinone diacetylene facilitates formation of thin films exhibiting a long-range, uniform pore structure. We show that light irradiation at distinct wavelengths plays a key role in the assembly process and generation of unique macro-porous morphology, by both initiating interactions between the carbon dots and the anthraquinone moieties and giving rise to the topotactic polymerization of the polydiacetylene network. We further demonstrate utilization of the macro-porous film as a photocatalytic platform for water pollutant degradation and as potential supercapacitor electrodes, both applications taking advantage of the high surface area, hydrophobicity, and pore structure of the film.

Enhancing Sensitivity in Gas Detection: Porous Structures in Organic Field-Effect Transistor-Based Sensors

Gas detection is crucial for detecting environmentally harmful gases. Organic field-effect transistor (OFET)-based gas sensors have attracted attention due to their promising performance and potential for integration into flexible and wearable devices. This review examines the operating mechanisms of OFET-based gas sensors and explores methods for improving sensitivity, with a focus on porous structures. Researchers have achieved significant enhancements in sensor performance by controlling the thickness and free volume of the organic semiconductor layer. Additionally, innovative fabrication techniques like self-assembly and etching have been used to create porous structures, facilitating the diffusion of target gas molecules, and improving sensor response and recovery. These advancements in porous structure fabrication suggest a promising future for OFET-based gas sensors, offering increased sensitivity and selectivity across various applications.

Study on stabilized mechanism of high internal phase Pickering emulsions based on commercial yeast proteins: Modulating the characteristics of Pickering particle via sonication

The primary significance of this work is that the commercial yeast proteins particles were successfully used to characterize the high internal phase Pickering emulsions (HIPPEs). The different sonication time (0,3,7,11,15 min) was used to modulate the structure and interface characteristics of yeast proteins (YPs) that as Pickering particles. Immediately afterward, the influence of YPs particles prepared at different sonication time on the rheological behavior and coalescence mechanism of HIPPEs was investigated. The results indicate that the YPs sonicated for 7 min exhibited a more relaxed molecular structures and conformation, the smallest particle size, the highest H0 and optimal amphiphilicity (the three-phase contact (θ) was 88.91°). The transition from extended to compact conformations of YPs occurred when the sonication time exceeded 7 min, resulting in an augmentation of size of YPs particles, a reduction in surface hydrophobicity (H0), and an elevation in hydrophilicity. The HIPPEs stabilized by YPs particles sonicated for 7 min exhibited the highest adsorption interface protein percentage and a more homogeneous three-dimensional (3D) protein network, resulting in the smallest droplet size and the highest storage (G'). The HIPPEs sample that stabilized by YPs particles sonicated for 15 min showed the lowest adsorption protein percentage. This caused a reduction in the thickness of its interface protein layer and an enlargement in the droplet diameter (D [3,2]). It was prone to droplet coalescence according to the equation used to evaluate the coalescence probability of droplets (Eq (2)). And the non-adsorbed YPs particles form larger aggregation structures in the continuous phase and act as "structural agents" in 3D protein network. Therefore, mechanistically, the interface protein layer formed by YPs particles sonicated 7 min contributed more to HIPPEs stability. Whereas the "structural agents" contributed more to HIPPEs stability when the sonication time exceeded 7 min. The present results shed important new light on the application of commercial YPs in the functional food fields, acting as an available and effective alternative protein.

Poly(N,N-diethylacrylamide)-endowed spontaneous emulsification during the breath figure process and the formation of membranes with hierarchical pores

The spontaneous emulsification for the formation of water-in-oil (W/O) or oil-in-water (O/W) emulsions needs the help of at least one kind of the third component (surfactant or cosolvent) to stabilize the oil-water interface. Herein, with the water/CS2-soluble polymer poly(N,N-diethylacrylamide) (PDEAM) as a surfactant, the spontaneous formation of water-in-PDEAM/CS2 emulsions is reported for the first time. The strong affinity between PDEAM and water or the increase of PDEAM concentration will accelerate the emulsification process with high dispersed phase content. It is demonstrated that the spontaneous emulsification of condensed water droplets into the PDEAM/CS2 solution occurs during the breath figure process, resulting in porous films with two levels of pore sizes (i.e., micron and submicron). The emulsification degree and the amounts of submicron-sized pores increase with PDEAM concentration and solidifying time of the solution. This work brings about incremental interest in spontaneous emulsification that may happen during the breath figure process. The combination of these two simultaneous processes provides us with an option to build hierarchically porous structures with condensed and emulsified water droplets as templates. Such porous membranes may have great potential in fields such as separation, cell culture, and biosensing.

Emergent Collective Motion of Self-Propelled Condensate Droplets

Recently, there is much interest in droplet condensation on soft or liquid or liquidlike substrates. Droplets can deform soft and liquid interfaces resulting in a wealth of phenomena not observed on hard, solid surfaces (e.g., increased nucleation, interdroplet attraction). Here, we describe a unique collective motion of condensate water droplets that emerges spontaneously when a solid substrate is covered with a thin oil film. Droplets move first in a serpentine, self-avoiding fashion before transitioning to circular motions. We show that this self-propulsion (with speeds in the 0.1-1  mm s^{-1} range) is fueled by the interfacial energy release upon merging with newly condensed but much smaller droplets. The resultant collective motion spans multiple length scales from submillimeter to several centimeters, with potentially important heat-transfer and water-harvesting applications.

Multifunctional Electrospun Nanofibers for Biosensing and Biomedical Engineering Applications

Nanotechnology is experiencing unprecedented developments, leading to the advancement of functional nanomaterials. The properties that stand out include remarkable porosity, high-specific surface area, excellent loading capacity, easy modification, and low cost make electrospun nanofibers. In the biomedical field, especially in biosensors, they exhibit amazing potential. This review introduces the principle of electrospinning, describes several structures and biomaterials of electrospun nanofibers used for biomedicine, and summarizes the applications of this technology in biosensors and other biomedical applications. In addition, the technical challenges and limitations of electrospinning for biomedicine are discussed; however, more research work is needed to elucidate its full potential.

Metallic Micro-Nano Network-Based Soft Transparent Electrodes: Materials, Processes, and Applications

Soft transparent electrodes (TEs) have received tremendous interest from academia and industry due to the rapid development of lightweight, transparent soft electronics. Metallic micro-nano networks (MMNNs) are a class of promising soft TEs that exhibit excellent optical and electrical properties, including low sheet resistance and high optical transmittance, as well as superior mechanical properties such as softness, robustness, and desirable stability. They are genuinely interesting alternatives to conventional conductive metal oxides, which are expensive to fabricate and have limited flexibility on soft surfaces. This review summarizes state-of-the-art research developments in MMNN-based soft TEs in terms of performance specifications, fabrication methods, and application areas. The review describes the implementation of MMNN-based soft TEs in optoelectronics, bioelectronics, tactile sensors, energy storage devices, and other applications. Finally, it presents a perspective on the technical difficulties and potential future possibilities for MMNN-based TE development.

Hierarchical Surface Instability in Polymer Films

This study demonstrates hierarchical instabilities in thin films. The hierarchical instabilities display three morphological characteristics: (1) windmill-like patterns at the macroscale, (2) Bénard cells and striations at the microscale, and (3) holes at the mesoscale. Such hierarchical instabilities occurred when spin coating was performed on high-volatile solutions under a high relative humidity (RH) but were suppressed when spin coating was performed on low-volatile solutions regardless of the RH. The high-volatile solutions comprise poly(4-vinylpyridine) (P4VP) in methanol or ethanol. The low-volatility solutions comprise P4VP in propanol or butanol. P4VP molecular weights, P4VP concentrations, spin rates, and film thicknesses are not vital factors in forming hierarchical instability in spin-coated P4VP films. Instead, the formation of hierarchical instabilities depends on the RH and solvent types. Namely, the hierarchical instabilities are driven by Bénard-Marangoni convection, water vapor condensation, and disturbance of spin-up and spin-off stages during spin coating of highly volatile solutions under high RH. Mechanisms of hierarchical instabilities are interpreted in detail.

Novel Capturer-Catalyst Microreactor System with a Polypyrrole/Metal Nanoparticle Composite Incorporated in the Porous Honeycomb-Patterned Film

A composite of polypyrrole/metal nanoparticles (PPy/MNPs) was selectively incorporated into the pores of a honeycomb-patterned porous polycaprolactone polymer film to fabricate a novel capturer-catalyst microreactor system. This fabrication involved a modified breath figure method, where the polymer solution containing metal ions as an oxidizing agent was cast under humid conditions along with the pyrrole monomer through an interfacial reaction in a one-step in situ process. The higher hydrophilicity of the metal ions compared to the polymer solution led to their self-assembly around the pore surface, resulting in the selective incorporation of the PPy/MNP composite into the porous film. Copper (Cu), silver (Ag), and gold (Au) were used for the PPy/MNP fabrication. Various methods characterized the fabricated film. Strong catalytic degradations of methylene blue and methyl orange were obtained with PCL-PPy/MNPs. Recycling experiments showed no loss of activity even after five cycles of recycling. Comparative analysis of PCL-PPy, PCL-MNP, and PCL-PPy/MNP results indicated the synergistic action of PPy and MNPs in dye degradation. High-performance liquid chromatography and mass spectroscopy analyses confirmed dye degradation after treatment with a fabricated microreactor. PPy might have acted as a capturer of the dye molecule and MNPs as a catalyst, thereby enhancing the efficiency of dye degradation. Additionally, the PCL-PPy/Cu composite exhibited strong antimicrobial properties against Gram-positive (Staphylococcus aureus) and Gram-negative bacteria (Escherichia coli) with no cytotoxicity as measured by the MTT assay. Therefore, the fabricated microreactor film has promising applications in various fields.

Unveiling the Interactions between Water Molecule Clusters and Conical Structures via Molecular Dynamics Simulations

Water scarcity presents a pressing global challenge, necessitating innovative solutions, such as the collection of water from the air using conical structures. However, current research primarily focuses on mist collection rather than on nanoscale clusters of water molecules. Under standard atmospheric conditions, water vapor predominantly exists as imperceptible clusters. Therefore, it is crucial to investigate the interactions between these water molecule clusters and conical structures, particularly regarding whether the conical shape induces Laplace pressure difference on the adhering cluster formations. To gain deeper insights and determine optimal droplet collection structures, we conducted molecular dynamics simulations to investigate interactions between water molecule clusters and conical structures. Our investigations focused on studying the interactions between conical structures and water molecule clusters with varying densities, as well as the impact of surface energies on the collection of water by these conical structures. Notably, our simulations unveiled the significant roles played by van der Waals forces and Laplace pressure in the process of collecting water molecule clusters. Furthermore, our simulations revealed that Janus conical structures, featuring two distinct surface energy regions, played a crucial role in promoting the aggregation of water molecules, resulting in the formation of larger droplets. This aggregation was driven by surface tension gradients, which arise from the contrasting wetting properties in different regions of the Janus structure. As a consequence, under the influence of gravitational forces, these larger droplets could eventually detach from the structure. Through the combined effects of surface tension gradients and gravitational forces, Janus conical structures offer a promising avenue for enhancing the collection efficiency of water from the air. Our research sheds light on the fundamental mechanisms governing water molecule cluster-based water collection and provides valuable insights for the design of more efficient and effective water collection systems.

Recent Advances in Triboelectric Nanogenerators: From Technological Progress to Commercial Applications

Serious climate changes and energy-related environmental problems are currently critical issues in the world. In order to reduce carbon emissions and save our environment, renewable energy harvesting technologies will serve as a key solution in the near future. Among them, triboelectric nanogenerators (TENGs), which is one of the most promising mechanical energy harvesters by means of contact electrification phenomenon, are explosively developing due to abundant wasting mechanical energy sources and a number of superior advantages in a wide availability and selection of materials, relatively simple device configurations, and low-cost processing. Significant experimental and theoretical efforts have been achieved toward understanding fundamental behaviors and a wide range of demonstrations since its report in 2012. As a result, considerable technological advancement has been exhibited and it advances the timeline of achievement in the proposed roadmap. Now, the technology has reached the stage of prototype development with verification of performance beyond the lab scale environment toward its commercialization. In this review, distinguished authors in the world worked together to summarize the state of the art in theory, materials, devices, systems, circuits, and applications in TENG fields. The great research achievements of researchers in this field around the world over the past decade are expected to play a major role in coming to fruition of unexpectedly accelerated technological advances over the next decade.

Oxidative-Reductive Near-Infrared Electrochromic Switching Enabled by Porous Vertically Stacked Multilayer Devices

Here, we demonstrate for the first time the ability of a porous π-conjugated semiconducting polymer film to enable facile electrolyte penetration through vertically stacked redox-active polymer layers, thereby enabling electrochromic switching between p-type and/or n-type polymers. The polymers P1 and P2, with structures diketopyrrolopyrrole (DPP)-π_bridge-3,4,-ethylenedioxythiophene (EDOT)-π_bridge [π_bridge = 2,5-thienyl for P1 and π_bridge = 2,5-thiazolyl for P2] are selected as the p-type polymers and N2200 (a known naphthalenediimide-dithiophene semiconductor) as the n-type polymer. Single-layer porous and dense (control) polymer films are fabricated and extensively characterized using optical microscopy, atomic force microscopy, scanning electron microscopy, and grazing incidence wide-angle X-ray scattering. The semiconducting films are then incorporated into single and multilayer electrochromic devices (ECDs). It is found that when a p-type (P2) porous top layer is used in a multilayer ECD, it enables electrolyte penetration to the bottom layer, enabling oxidative electrochromic switching of the P1 bottom layer at low potentials (+0.4 V versus +1.2 V with dense P2). Importantly, when using a porous P1 as the top layer with an n-type N2200 bottom layer, dynamic oxidative-reductive electrochromic switching is also realized. These results offer a proof of concept for development of new types of multilayer electrochromic devices where precise control of the semiconductor film morphology and polymer electronic structure is essential.

Porous honeycomb film membranes enhance endothelial barrier integrity in human vascular wall bilayer model compared to standard track-etched membranes

In vitro vascular wall bilayer models for drug testing and disease modeling must emulate the physical and biological properties of healthy vascular tissue and its endothelial barrier function. Both endothelial cell (EC)-vascular smooth muscle cell (SMC) interaction across the internal elastic lamina (IEL) and blood vessel stiffness impact endothelial barrier integrity. Polymeric porous track-etched membranes (TEM) typically represent the IEL in laboratory vascular bilayer models. However, TEM stiffness exceeds that of diseased blood vessels, and the membrane pore architecture limits EC-SMC interaction. The mechanical properties of compliant honeycomb film (HCF) membranes better simulate the Young's modulus of healthy blood vessels, and HCFs are thinner (4 vs. 10 μm) and more porous (57 vs. 6.5%) than TEMs. We compared endothelial barrier integrity in vascular wall bilayer models with human ECs and SMCs statically cultured on opposite sides of HCFs and TEMs (5 μm pores) for up to 12 days. Highly segregated localization of tight junction (ZO-1) and adherens junction (VE-cadherin) proteins and quiescent F-actin cytoskeletons demonstrated superior and earlier maturation of interendothelial junctions. Quantifying barrier integrity based on transendothelial electrical resistance (TEER), membranes showed only minor but significant TEER differences despite enhanced junctional protein localization on HCF. Elongated ECs on HCF likely experienced greater paracellular diffusion than blocky ECs on TEM. Also, larger populations of plaques of connexin 43 subunit-containing gap junctions suggested enhanced EC-SMC communication across the more porous, thinner HCF. Compared with standard TEMs, engineered vascular wall bilayers cultured on HCFs better replicate physiologic endothelial barrier integrity.

Exploiting breath figure reversibility for in situ pattern modulation and hierarchical design

The breath figure (BF) method employs condensation droplets as dynamic templates for patterning polymer films. In the classical approach, dropwise condensation and film solidification are simultaneously induced through solvent evaporation, leading to empirically derived patterns with limited predictability of the final design. Here we use the temporally arrested BF methodology, controlling condensation and polymerisation independently to create diverse BF patterns with varied pore size, arrangement and distribution. External temperature control enables us to further investigate and exploit the inherent reversibility of the phase change process that governs the pattern formation. We modulate the level of subcooling and superheating to achieve subsequent regimes of condensation and evaporation, permitting in situ regulation of the droplet growth and shrinkage kinetics. The full reversibility of the phase change processes joined with active photopolymerisation in the current approach thus allows arresting of predictable BF kinetics at intermediate stages, thereby accessing patterns with varied pore size and spacing for unchanged material properties and environmental conditions. This simultaneous active control over both the kinetics of phase change and polymer solidification offers affordable routes for the fabrication of diverse predictable porous surfaces; manufacture of monolithic hierarchical BF patterns are ultimately facilitated through the advanced control of the BF assembly using the method presented here.

A Review of Smart Superwetting Surfaces Based on Shape-Memory Micro/Nanostructures

Bioinspired smart superwetting surfaces with special wettability have aroused great attention from fundamental research to technological applications including self-cleaning, oil-water separation, anti-icing/corrosion/fogging, drag reduction, cell engineering, liquid manipulation, and so on. However, most of the reported smart superwetting surfaces switch their wettability by reversibly changing surface chemistry rather than surface microstructure. Compared with surface chemistry, the regulation of surface microstructure is more difficult and can bring novel functions to the surfaces. As a kind of stimulus-responsive material, shape-memory polymer (SMP) has become an excellent candidate for preparing smart superwetting surfaces owing to its unique shape transformation property. This review systematically summarizes the recent progress of smart superwetting SMP surfaces including fabrication methods, smart superwetting phenomena, and related application fields. The smart superwettabilities, such as superhydrophobicity/superomniphobicity with tunable adhesion, reversible switching between superhydrophobicity and superhydrophilicity, switchable isotropic/anisotropic wetting, slippery surface with tunable wettability, and underwater superaerophobicity/superoleophobicity with tunable adhesion, can be obtained on SMP micro/nanostructures by regulating the surface morphology. Finally, the challenges and future prospects of smart superwetting SMP surfaces are discussed.

Selenium-decorated biocompatible honeycomb films with redox-switchable surface for controlling cell adhesion/detachment

HYPOTHESIS

Selenium (Se)-containing compound is sensitive to redox stimulation, showing hydrophobic-hydrophilic reversible transition. Introduction of such compound into honeycomb film could confer on it redox-switchable surface wettability, which is expected to control cell adhesion/detachment behavior.

EXPERIMENTS

Didodecyl selenide was designed and mixed with polystyrene to prepare honeycomb films using "breath figure" method. The film microstructures were characterized by scanning electron microscope and atomic force microscopy, and the arrangement of Se atoms in honeycomb film was determined by X-ray photoelectron spectroscopy and energy dispersive spectrometry. The variation of film wettability upon the alternating stimulation of H₂O₂ and Vc was examined. Then the cell adhesion, proliferation, and controlled detachment on honeycomb films were conducted.

FINDINGS

The introduction of didodecyl selenide helps to form ordered honeycomb film, and Se atoms were found to located on the bottom, pore walls, and top surface of the film. The presence of didodecyl selenide not only greatly improves film biocompatibility by enhancing cell thioredoxin reductase activity, but also imparts the film with H₂O₂-/vitamin C-regulated tunable wettability that controls cell adhesion and detachment. H₂O₂ treatment produces a hydrophilic surface for cell adhesion and proliferation, whereas the addition of vitamin C generates hydrophobic surfaces and allows cells to detach while remaining alive with high activity.

Memory Re-Condensation

This paper reveals a phenomenon of memory in dropwise condensation in open air. After a first condensation process and complete evaporation of the condensed droplets, further condensations proceed with droplets nucleating at the very places where former droplets evaporated. The origin of this phenomenon is due to the incorporation of airborne salts during the first droplet condensation and its further concentration during droplet evaporation. Salts act as preferential nucleation sites and humidity sinks. The potential impact of this phenomenon on controlled breath figure patterns and plant metabolism is discussed.

High-Performance Nitric Oxide Gas Sensors Based on an Ultrathin Nanoporous Poly(3-hexylthiophene) Film

Conjugated polymer (CP)-based organic field-effect transistors (OFETs) have been considered a potential sensor platform for detecting gas molecules because they can amplify sensing signals by controlling the gate voltage. However, these sensors exhibit significantly poorer oxidizing gas sensing performance than their inorganic counterparts. This paper presents a high-performance nitric oxide (NO) OFET sensor consisting of a poly(3-hexylthiophene) (P3HT) film with an ultrathin nanoporous structure. The ultrathin nonporous structure of the P3HT film was created via deposition through the shear-coating-assisted phase separation of polymer blends and selective solvent etching. The ultrathin nonporous structure of the P3HT film enhanced NO gas diffusion, adsorption, and desorption, resulting in the ultrathin nanoporous P3HT-film-based OFET gas sensor exhibiting significantly better sensing performance than pristine P3HT-film-based OFET sensors. Additionally, upon exposure to 10 ppm NO at room temperature, the nanoporous P3HT-film-based OFET gas sensor exhibited significantly better sensing performance (i.e., responsivity ≈ 42%, sensitivity ≈ 4.7% ppm-1, limit of detection ≈ 0.5 ppm, and response/recovery times ≈ 6.6/8.0 min) than the pristine P3HT-film-based OFET sensors.

Biopolymer Honeycomb Microstructures: A Review

In this review, we present a comprehensive summary of the formation of honeycomb microstructures and their applications, which include tissue engineering, antibacterial materials, replication processes or sensors. The history of the honeycomb pattern, the first experiments, which mostly involved the breath figure procedure and the improved phase separation, the most recent approach to honeycomb pattern formation, are described in detail. Subsequent surface modifications of the pattern, which involve physical and chemical modifications and further enhancement of the surface properties, are also introduced. Different aspects influencing the polymer formation, such as the substrate influence, a particular polymer or solvent, which may significantly contribute to pattern formation, and thus influence the target structural properties, are also discussed.

Self-assembled polylactic acid (PLA): Synthesis, properties and biomedical applications

The surface morphology and topography of cell culture substrates play an important role in cell proliferation and growth. Regulation of the surface microstructure allows the development of tissue culture media suitable for different cells. Polylactic acid (PLA) is a biobased and biodegradable (under defined conditions) polymer with low immunogenicity, non-toxicity, and good mechanical properties, which have facilitated their pharmaceutical and biomedical applications. This review summarizes recent advances in the synthesis and self-assembly of surface microstructure based on PLA materials and discusses their biomedical applications such as cell culturing and tissue engineering.

Self-assembled porous polymer films for improved oxygen sensing

Absolute oxygen sensors based on quenching of phosphorescence have been the subject of numerous studies for the monitoring of biological environments. Here, we used simple fabrication techniques with readily available polymers to obtain high performance phosphorescent films. Specifically, evaporation-based phase separation and the breath figure technique were used to induce porosity. The pore sizes ranged from ∼ 37 nm to ∼ 141 μ m while the maximum average porosity achieved was ∼ 74%. The oxygen sensing properties were evaluated via a standarised calibration procedure with an optoelectronic setup in both transmission and reflection based configurations. When comparing non-porous and porous films, the highest improvements achieved were a factor of ∼ 7.9 in dynamic range and ∼ 7.3 in maximum sensitivity, followed by an improved linearity with a half-sensitivity point at 43% O2 V/V. Also, the recovery time was reduced by an order of magnitude in the high porosity film and all samples prepared were not affected by variations in the humidity of the surrounding environment. Despite the use of common polymers, the fabrication techniques employed led to the significant enhancement of oxygen sensing properties and elucidated the relation between porous film morphologies and sensing performance.

Readily Accessible Metallic Micro-Island Arrays for High-Performance Metal Oxide Thin-Film Transistors

Thin-film transistors using metal oxide semiconductors are essential in many unconventional electronic devices. Nevertheless, further advances will be necessary to broaden their technological appeal. Here, a new strategy is reported to achieve high-performance solution-processed metal oxide thin-film transistors (MOTFTs) by introducing a metallic micro-island array (M-MIA) on top of the MO back channel, where the MO is a-IGZO (amorphous indium-gallium-zinc-oxide). Here Al-MIAs are fabricated using honeycomb cinnamate cellulose films, created by a scalable breath-figure method, as a shadow mask. For IGZO TFTs, the electron mobility (µ_e ) increases from ≈3.6 cm² V^-1 s^-1 to near 15.6 cm² V^-1 s^-1 for optimal Al-MIA dimension/coverage of 1.25 µm/51%. The Al-MIA IGZO TFT performance is superior to that of controls using compact/planar Al layers (Al-PL TFTs) and Au-MIAs with the same channel coverage. Kelvin probe force microscopy and technology computer-aided design simulations reveal that charge transfer occurs between the Al and the IGZO channel which is optimized for specific Al-MIA dimensions/surface channel coverages. Furthermore, such Al-MIA IGZO TFTs with a high-k fluoride-doped alumina dielectric exhibit a maximum µ_e of >50.2 cm² V^-1 s^-1 . This is the first demonstration of a micro-structured MO semiconductor heterojunction with submicrometer resolution metallic arrays for enhanced transistor performance and broad applicability to other devices.

Regulating Na Electrodeposition by Sodiophilic Grafting onto Porosity-Gradient Gel Polymer Electrolytes for Dendrite-Free Sodium Metal Batteries

Sodium metal batteries have been emerging as promising candidates for post-Li battery systems owing to the natural abundance, low costs, and high energy density of Na metal. However, exploiting an Na metal anode is accompanied by uncontrolled Na electrodeposition, particularly concerning dendrite growth, hampering practical Na metal battery applications. Herein, we propose sodiophilic gel polymer electrolytes with a porosity-gradient Janus structure to alleviate Na dendrite growth. Tethering only 1.1 mol % sodiophilic poly(ethylene glycol) to poly(vinylidene fluoride-co-hexafluoropropylene) suppresses Na dendrites by regulating homogeneous Na⁺ distribution, which relies on molecular-level coordination between Na⁺ and the sodiophilic functional groups. By exploiting the porosity-gradient Janus structure, we have demonstrated that regular porosity and well-defined morphology of polymer electrolytes, particularly at the Na/electrolyte interface, significantly impact dendrite growth. This study provides new insights into the rational design of Na dendrite-suppressing polymer electrolytes, primarily focusing on the ion-regulating ability achieved by surface engineering.

Self-assembly, alignment, and patterning of metal nanowires

Armed with the merits of one-dimensional nanostructures (flexibility, high aspect ratio, and anisotropy) and metals (high conductivity, plasmonic properties, and catalytic activity), metal nanowires (MNWs) have stood out as a new class of nanomaterials in the last two decades. They are envisaged to expedite significantly and even revolutionize a broad spectrum of applications related to display, sensing, energy, plasmonics, photonics, and catalysis. Compared with disordered MNWs, well-organized MNWs would not only enhance the intrinsic physical and chemical properties, but also create new functions and sophisticated architectures of optoelectronic devices. This paper presents a comprehensive review of assembly strategies of MNWs, including self-assembly for specific structures, alignment for anisotropic constructions, and patterning for precise configurations. The technical processes, underlying mechanisms, performance indicators, and representative applications of these strategies are described and discussed to inspire further innovation in assembly techniques and guide the fabrication of optoelectrical devices. Finally, a perspective on the critical challenges and future opportunities of MNW assembly is provided.

Animal- and Human-Inspired Nanostructures as Supercapacitor Electrode Materials: A Review

Human civilization has been relentlessly inspired by the nurturing lessons; nature is teaching us. From birds to airplanes and bullet trains, nature gave us a lot of perspective in aiding the progress and development of countless industries, inventions, transportation, and many more. Not only that nature inspired us in such technological advances but also, nature stimulated the advancement of micro- and nanostructures. Nature-inspired nanoarchitectures have been considered a favorable structure in electrode materials for a wide range of applications. It offers various positive attributes, especially in energy storage applications, such as the formation of hierarchical two-dimensional and three-dimensional interconnected networked structures that benefit the electrodes in terms of high surface area, high porosity and rich surface textural features, and eventually, delivering high capacity and outstanding overall material stability. In this review, we comprehensively assessed and compiled the recent advances in various nature-inspired based on animal- and human-inspired nanostructures used for supercapacitors. This comprehensive review will help researchers to accommodate nature-inspired nanostructures in industrializing energy storage and many other applications.

Fabrication of Adsorption-Type Hierarchical Functional Films by Using a Facile Swollen Based Breath Figure Method

The morphology transition from primary to hierarchical adsorption-type microporous domains of amphiphilic block copolymer (BCP) honeycomb-structured films is demonstrated by a facile swollen based breath figure (BF) method. The characteristic parameters of poly(4-vinylpyridine)-block-polystyrene (P4VP-b-PS) hierarchical micro- and submicro-porous films can be controlled by changing the length of segments or subsequent swelling conditions. A plausible mechanism is demonstrated in this research. A typical amphiphilic BCP with very low volume content of hydrophilic blocks (f_P4VP ≤ 0.050) can efficiently stabilize water droplets and inherently assist in the formation of morphology transition. This BCP film can be used for Cr(VI) removal from wastewater, which additionally has enormous potential application in the field of novel optical devices, soft lithography, size-selective separation, etc. This article is protected by copyright. All rights reserved.

Optimization of Printed Polyaniline Composites for Gas Sensing Applications

Polyaniline (PANI) films are promising candidates for electronic nose-based IoT applications, but device performances are influenced by fabrication parameters and ambient conditions. Affinities of different PANI composites to analytes for gas sensing applications remain elusive. In this study, we investigate the material properties in detail for two different dopant systems: F4TCNQ and carbon black. Using a reproducibility-driven approach, we investigate different dopant concentrations in regard to their sensitivity and specificity towards five relevant markers for breath cancer diagnosis. We benchmark the system using ammonia measurements and evaluate limits of detection. Furthermore, we provide statistical analysis on reproducibility and pave the way towards machine learning discrimination via principal component analysis. The influence of relative humidity on sensor hysteresis is also investigated. We find that F4TCNQ-doped PANI films show improved reproducibility compared to carbon black-doped films. We establish and quantify a tradeoff between sensitivity, reproducibility, and environmental stability by the choice of dopant and concentrations ratios.

Fabrication of a nanocomposite film decorated with highly dispersive nanoparticles by following an interface-induced strategy

A polymer nanocomposite film decorated with highly dispersive nanoparticles was prepared by a liquid-liquid interface induced self-assembly method based on a breath figure process. The distribution as well as the orientation preference of the Janus particles within the polymer matrix could be dynamically controlled by adjusting the environmental conditions. Antibacterial and photocatalytic functionality was obtained for the nanocomposite films decorated with silver and titanium dioxide nanoparticles, respectively.

Temporally Arrested Breath Figure

Since its original conception as a tool for manufacturing porous materials, the breath figure method (BF) and its variations have been frequently used for the fabrication of numerous micro- and nanopatterned functional surfaces. In classical BF, reliable design of the final pattern has been hindered by the dual role of solvent evaporation to initiate/control the dropwise condensation and induce polymerization, alongside the complex effects of local humidity and temperature influence. Herein, we provide a deterministic method for reliable control of BF pore diameters over a wide range of length scales and environmental conditions. To this end, we employ an adapted methodology that decouples cooling from polymerization by using a combination of initiative cooling and quasi-instantaneous UV curing to deliberately arrest the desired BF patterns in time. Through in situ real-time optical microscopy analysis of the condensation kinetics, we demonstrate that an analytically predictable self-similar regime is the predominant arrangement from early to late times O(10-100 s), when high-density condensation nucleation is initially achieved on the polymer films. In this regime, the temporal growth of condensation droplets follows a unified power law of D ∝ t. Identification and quantitative characterization of the scale-invariant self-similar BF regime allow fabrication of programmed pore size, ranging from hundreds of nanometers to tens of micrometers, at high surface coverage of around 40%. Finally, we show that temporal arresting of BF patterns can be further extended for selective surface patterning and/or pore size modulation by spatially masking the UV curing illumination source. Our findings bridge the gap between fundamental knowledge of dropwise condensation and applied breath figure patterning techniques, thus enabling mechanistic design and fabrication of porous materials and interfaces.