We Should Expect More out of Our Sewage Sludge

A review on waste activated sludge pretreatment for improved volatile fatty acids production and their upcycling into polyhydroxyalkanoates

Waste activated sludge (WAS), a byproduct of wastewater treatment (WWTPs) facilities is challenging to manage because of its high organic content. Most of WAS is managed via anaerobic digestion (AD) to produce biogas, which is not deemed economically viable. The AD of WAS into volatile fatty acids (VFA) and their subsequent upcycling into polyhydroxyalkanoates (PHA) is gaining popularity due to their high value and uses. However, the fundamental issue with WAS is its low solubility, and pretreatment is required to increase it. Pretreatment disintegrates sludge floc and enhances its solubility, supports acetogens, and inhibits methanogens, leading to increased VFA synthesis in the AD process. The key factors influencing VFA yield include the size of the sludge granules, the mixing rate, and the presence of resistant organic components. Fermented broth containing VFA from AD can be utilized directly as a feedstock for microbial fermentation to produce PHA using both pure as well as mixed cultures. Utilisation of mixed cultures is useful since they are robust, able to consume a wide range of substrates, and do not require sterility. In addition, the VFA, which is made up of various organic acids, impacts the structure, productivity, characteristics, and type of PHA produced by microbial communities. Considering the importance of WAS management through VFA production and its integration with PHA production process this review article discusses the WAS pretreatment strategies, various factors that influence the AD process, trends in VFA to PHA production technologies with challenges, and possible solutions for integrated process development.

Copper (Cu) and lead (Pb) treatment via two-stage pH-controlled fluidized-bed non-seeded granulation process

The two-stage pH-controlled fluidized-bed non-seeded granulation process for treating Cu and Pb was explored. This investigation specifically examined operational conditions including Cu-to-Pb molar ratio (MR1), metal-to-carbonate molar ratio (MR2), hydraulic retention time (HRT), and first-stage pH (pH1). Multilayered, spherical, brittle, light blue granules were recovered. X-ray diffraction only detected cerussite (PbCO3) crystals, while the Pb Pourbaix diagram and solubility curve confirmed the cerussite stability. Meanwhile, the presence of bicarbonate could feasibly alter the prevailing voltage potential, generating the Cu-hydroxide interface in water. Furthermore, copper species in granules possibly formed amorphous solids due to low copper levels and inhibition of ionic Pb. Besides PbCO3 crystals, the development of amorphous Cu-carbonate hydroxide could also occur during granulation. The transition to pH 8.0 in the second stage could affect the solid solubility and the surface charge influencing the accumulation and the agglomeration, respectively. Operational conditions also significantly impacted particle growth, total removal, and accumulation rates. The sub-optimal condition was found at MR1 = 5.0, MR2 = 1.5, HRT = 22.5 min, and pH1 = 7.5 producing relatively high percentages of large granules, high removal efficiencies > 99 %, and accumulation rates between 80 % and 95 %.

Mini-review: Nanoparticles for enhanced biogas upgrading

This mini-review is intended to explore the innovative applications of nanoparticles (NPs) in biogas upgrading, emphasizing their capacity to enhance biogas quality. Numerous studies underscore how NPs, when applied during anaerobic digestion, can boost not only the quantity but also the quality of the produced biogas, leading to reduce significantly the concentration of hydrogen sulphide or even to remove it completely. Moreover, NPs are proving to be excellent alternatives as adsorbent materials, achieving up to 400 mgH2S g-1 NPs. In addition, new studies are exploring the application of NPs to increase the efficiency of biological treatments thanks to their unique features. This review also emphasizes the potential benefits and addresses the challenges that need to be overcome for these technologies to reach their full potential, ultimately contributing to the development of a sustainable and environmentally friendly energy landscape.

Innovative Approach to Sustainable Fertilizer Production: Leveraging Electrically Assisted Conversion of Sewage Sludge for Nutrient Recovery

Efforts addressing sludge management, food security, and resource recovery have led to novel approaches in these areas. Electrically assisted conversion of sludge stands out as a promising technology for sewage sludge valorization, producing nitrogen and phosphorus-based fertilizers. The adoption of this technology, which could lead to a fertilizer circular economy, holds the potential to catalyze a transformative change in wastewater treatment facilities toward process intensification, innovation, and sustainability. This paper provides insights into the economic aspects of the technology, policy considerations, and challenges involved in realizing the potential of electrified processes for sludge valorization. To demonstrate the impact of the technology, a case study for its implementation in the United States assuming the municipal wastewater treatment plants market is discussed. It was found that electrically assisted sludge conversion could enable the recovery of nitrogen and phosphorus from waste, representing up to 9% of the nitrogen and 32% of the phosphorus consumption of the U.S. for fertilizer use. This technology also enables full electrification and modularization of the process, thereby presenting significant economic and environmental opportunities.

Strategic carbon emission assessment in sludge treatment: A dynamic tool for low-carbon transformation

The carbon-neutral target presents a significant challenge for the sewage sludge treatment and disposal (SSTD) industry, necessitating strategic planning for a low-carbon transition. However, flexible and comprehensive carbon emission analysis tools to support this goal remain lacking. This study presents a carbon emission analysis tool to evaluate the carbon emission characteristics and future mitigation potentials of SSTD. The tool integrates life cycle inventory (LCI) modeling-based analysis, sensitivity analysis, regression analysis, and scenario analysis. Carbon emissions are dynamically calculated based on sludge properties, technological level, and industry external parameters, providing a foundation for adaptable evaluation tailored to local conditions. The framework considers the potential effects of multi-parameter and multi-aspect changes in scene design, both within and outside the industry, to achieve dynamic and comprehensive simulations. A case study conducted in Wuhan, China, demonstrated the usability and application processes of the framework. The results indicated that carbon emissions from SSTD are projected to more than double from 2021 to 2060 without interventions. Among the mitigation measures, energy and chemical savings would yield the largest reduction potential, followed by the technical layout adjustment and the promotion of energy efficiency. Operational optimization in the sludge industry and outside the industry would contribute the least. With all mitigation measures applied, emissions could decrease to -82.91 kt CO2-eq in 2060, equivalent to 13.03% compensation for emissions from the sewage treatment line. Among all the processes, incineration routes are recommended due to their current and future low carbon emissions. The cooperative resource route of anaerobic digestion and land use also shows promise as it progressively demonstrates superior performance with increasing organic matter and nutrient content of sludge. Critical factors, sub-processes, and emission types for different routes were identified and can be optimized accordingly. The developed method demonstrates sufficient flexibility to be applied to other cities and larger-scale regions, thereby offering technical and strategic support for SSTD towards carbon-neutral operation.

Socio-environmental externalities of sewage waste management

Conventional sewage management is expensive and inefficient, putting the environment and public health at risk, making access to sewage services difficult for everyone. Reusing sewage waste has agricultural and economic potential, but can contain harmful contaminants if not treated properly. This review is based on the hypothesis that the destination of sewage waste generates environmental and social externalities, which have not yet been widely compared. With the aim of identifying, from the literature, the socio-environmental externalities generated by different sewage waste management approaches, a systematic review of the literature was carried out, including 244 documents, with 50 % of these discussing impacts of conventional treatment and 37 % analyzing the reuse of waste. The main impacts and externalities were evaluated in three situations: untreated sewage, treated sewage, and reused waste. The results indicate that sewage waste has an underutilized economic value and can generate revenue, reduce operational costs and electricity expenses. Six negative externalities generated by conventional sewage treatment were identified: health costs; environmental cleaning; carbon offsetting; damage to tourism; damage to fishing and agriculture; and real estate depreciation. In reuse, there is a risk of two negative externalities: health costs and environmental cleaning, but two positive externalities were also identified: the reduction of phosphate rock mining and the neutralization of carbon credits. The complexity of the transition to sustainable sewage treatment practices is highlighted given the lack of consensus on the safe use of sewage waste, the lack of regulatory standardization, implementation costs and differences in regional parameters, highlighting the need for preliminary experimentation in a multidisciplinary and contextualized approach, considering comparative externalities among the available sewage waste management possibilities.

Multifaceted Impact of Lipid Extraction on the Characteristics of Polymer-Based Sewage Sludge towards Sustainable Sludge Management

Dewatered sludge (DS) is a sewage sludge with a unique property due to extracellular polymeric substances (EPSs) and polymer flocculants. These components form a stable 3D polymer network to increase dewatering efficiency, leaving behind valuable materials such as lipids. This article explored the influences of DS particle size on lipid yield and the effects of extraction on the chemical, morphological, and thermal properties of the residual dewatered sludge (RDS). Lipid yields with unimodal distribution were observed across the particle size ranges (<0.5, 0.5-1.0, 1.0-2.0, 2.0-4.0, and 4.0 mm). The highest lipid yield of 1.95% was extracted from 1.0-2.0 mm after 4 h at 70 °C and 0.1 g/mL sludge-to-solvent ratio. Efficiency was influenced by the DS's morphology, facilitating solvent infiltration and pore diffusion. The extraction process reduced water and organic fractions, resulting in higher thermal stability. Bibliometric analysis of "extraction*" and "sewage sludge" shows increasing research interest from 1973 to 2024. Five research clusters were observed: heavy metal speciation and stabilization, sludge and its bioavailability, extraction techniques and resource recovery, contaminants remediation, as well as phosphorus recovery and agricultural applications. These clusters highlight the diverse approaches to researching DS and RDS while promoting sustainable waste management.

GLDA exhibits advantages in the phytoextraction of Cd and Ni in land-applied municipal sludge

Landscape utilization is a green and environment-friendly way of disposing of compost sludge. Garden plants can extract heavy metals from the sludge of land use, but the effect is not enough to be widely used. Chelating agents have been found to facilitate the extraction of heavy metals from plants and are expected to be popularized if they are also environmentally friendly. In this study, the effects of methylglycinediacetic acid trisodium salt (MGDA), tetrasodium glutamate diacetate (GLDA), and ethylene diamine tetraacetate (EDTA) on the extraction of Ni and Cd from compost sludge by Symphytum officinale L. were studied through the pot experiment. Compared with the control group, the application of 5-10 mmol kg-1 MGDA and 1-9 mmol kg-1 GLDA promoted plant growth, while the application of 3-4 mmol kg-1 EDTA inhibited plant growth. The highest Ni content in shoots appeared in 4 mmol kg-1 GLDA treatment, which was 4.2 times that of the CK group. The highest shoot Cd concentration appeared in 4 mmol kg-1 EDTA treatment, 6.5 times that of CK. The promotion effects of the three reagents on the acid-extractable state of Cd were similar, while that of GLDA on the acid-extractable state of Ni was outstanding. The results of this study suggested that S. officinale could be a potential phytoextraction plant for Cd and Ni, and GLDA could friendly promote the Ni phytoextraction ability of the plant. The study provides a new and efficient method for phytoremediation of heavy metals in soil.

Guidelines for efficient nitrogen preservation in sewage sludge-based fertilizers

This study explores sustainable methods to mitigate nitrogen (N) loss in agriculture amid rising food demands and limited arable land. It examines sewage sludge (SS) as an alternative to synthetic N fertilizers. SS is rich in nitrogen (4.21 ± 0.42 %) and phosphorus (3.60 ± 0.72 %), making it suitable for nutrient recovery and soil enhancement. Unfavorable sludge management methods result in the loss of 950,000 tons of nitrogen, meeting almost 10 % of the EU's nitrogen fertilization demand. This research evaluates SS treatment methods, including chemical conversion, thermal treatment, and biological composting, focusing on nitrogen conservation efficiency. Results show nitrogen loss during hydrolysis is minimized at pH 4 to 8 but increases significantly as ammonia (NH3) at pH 9 to 11, ranging from 4.2 % to 9 %. Neutralizing the hydrolysate is crucial; using solid KOH resulted in 13.5 % nitrogen loss, 11 times more than using slightly alkaline ash (1.22 %). Adding ash during drying reduced nitrogen emissions by 30 % compared to traditional drying at 105 °C. Improving the C/N ratio with food residues reduced nitrogen losses by 46.3 % during composting. These findings highlight the importance of pH control in chemical processes and temperature regulation in thermal treatments. Adding residues from other processes, such as biomass combustion waste, enhances SS processing conditions. Understanding nitrogen retention mechanisms is crucial for the environmental sustainability of SS usage. Efficient nitrogen retention strategies improve the fertilization value of SS and reduce its environmental footprint by lowering greenhouse gas emissions, particularly ammonia. Reducing nitrogen loss during SS treatment significantly lowers ammonia emissions, a major contributor to greenhouse gas emissions. These results help determine optimal methods for managing and processing SS to minimize emissions and increase agricultural usability.

Influence of policymakers and civil society stakeholders on sewage sludge management strategies: Empirical results from European utilities

Sewage sludge management is crucial for water utilities to move towards a circular valorisation of resources. The current literature focuses mainly on the technological aspects of sludge management strategies. However, the current discussion of these strategies does not consider possible pressures arising from the utilities' civil society stakeholders and from policymakers. To fill this gap, this paper develops a conceptual framework, based on the current literature, that identifies the utility's key decisions on sludge management strategies (valorisation route, overperformance and vertical integration), and links them to possible pressures arising from civil society and existing regulations. Subsequently, the study validates the framework through a multiple explanatory case study, investigating the empirical relevance of such pressures in six water utilities across Europe. The influence of citizens and municipalities is found to be crucial in the choice of sludge valorisation routes. Economic instruments, command and control instruments and, new to the literature, regulatory uncertainty are found to be key policy features influencing utilities' decisions on sludge management. The paper provides a first-of-its-kind investigation that highlights the mechanisms through which policymakers and civil society stakeholders shape utilities' sewage sludge management strategies. The results complement and extend existing theoretical knowledge on the role of institutional pressures in the implementation of sustainable environmental systems.

Domestic wastewater sludge valorization: Multi-criteria evaluation of anaerobic digestion vs. hydrothermal liquefaction

The emerging hydrothermal liquefaction (HTL) process is evaluated against the classical anaerobic digestion (AD) processes for stabilizing wastewater sludges and recovering their energy- and nutrient-contents. Although HTL affords faster stabilization, better process stability, and liquid fuel and sterile fertilizer recovery, it suffers from higher energy demand and lower technology readiness level. For a rational comparison of these pathways, a multi-criteria evaluation is conducted considering 21 technical, environmental, economic, and social criteria. Criteria values for the HTL-pathway were derived from laboratory tests while those for the AD-pathway were compiled from literature. Of the 16 process alternatives evaluated, the AD-pathway including nitrogen-recovery by air-stripping and phosphorus recovery by the MEPHREC® process ranked first followed by the HTL-pathway. This multi-criteria study suggests that the HTL-pathway could be engineered as a superior alternative for sludge stabilization and resource recovery if phosphorus recovery and its technology readiness level could be improved.

Microplastic abundance in sludge-treated fields: Variance and estimated half-life

This study investigated the abundance of microplastic (MP) in agricultural soil fertilised with sludge, assessing the variation in MP count and estimated mass in three long-term field trials treated excessively with sludge in 2003-2012. Ten samples were taken from each of the three fields with concentrations ranging from 2392 to 48,791 counts kg-1, where over 50 % of the MPs were polyester and acrylic. Due to the considerable variation in concentration, the impact of the number of sub-samples on the predicted measured concentration was estimated applying a Monto Carlo simulation approach. Choosing the number of sampling points is a compromise between acceptable sampling error and available resources. The simulations showed an increasingly high risk of obtaining an outlier when taking less than approx. ten subsamples. When ending fertilisation with sludge, the estimated half-life for the MPs measured by counts was approx. 2.5 years, whereas the half-life for the MP estimated mass was approx. 4 years. Hence, smaller particles seemed to degrade and/or migrate elsewhere the fastest.

A high-throughput analytical method for complex contaminant mixtures in biosolids

Biosolids are rich in organic matter and other nutrients that contribute to environmental and agricultural sustainability by improving soil textural and biological properties and enhancing plant growth when applied to agricultural crops. Land application of biosolids encourages resource recovery and circumvents drawbacks associated with landfilling or incineration. However, biosolids contain numerous chemicals at trace levels, and quantitative analysis of such mixtures in this complex matrix is crucial for understanding and managing application risks. There are currently few analytical methods available that are capable of extracting and quantifying a large range of the emerging contaminants found in biosolids. In this study, a simplified, rapid, and robust method of analysis was developed and validated for a high-priority organic contaminant mixture of 44 endocrine disrupting compounds known to occur in biosolids. Analytes consisted of chemicals from many classes with a wide range of physiochemical properties (e.g., log Kow values from -1.4 to 8.9). The biosolids extraction and cleanup protocol was validated for 42 of the targeted compounds. The UPLC-MS2 parameters were validated for all 44 organic contaminants targeted for study. From the two batches of biosolids tested using this analytical method, most of the targeted contaminants (86%) were detected with 100% frequency at concentrations ranging from 0.036 to 10,226 μg/kg dw. Performance results highlighted that internal standards alone could not negate biosolids matrix effects; thus, internal standards and the standard addition method were used for residue quantification. This was the first study to detect and quantify 6PPD-q in biosolids, and the first to quantify lidocaine and 11 other chemicals in biosolids using a single analytical method. This method may be expanded for analysis of additional chemicals in biosolids and comparable matrices.

Effect of temperature on hydrothermal liquefaction of high lipids and carbohydrates content municipal primary sludge

The study assessed the valorisation of primary sludge through HTL and the influence of temperature on the product distribution. The experiments were conducted at different temperatures, 30 min reaction time, and 100 rpm stirring rate. The maximum yield of biocrude produced was 39.47% at 270 °C. The best yield of oils was 23.96% at 300 °C. The lowest yield of asphaltenes was 12.50% at 240 °C. HHV for biocrude were always between 39 and 41 MJ/kg, close to petroleum. Best energy recovery for biocrude was 82% at 270 °C.

Characterizing the Opportunity Space for Sustainable Hydrothermal Valorization of Wet Organic Wastes

Resource recovery from wet organic wastes can support circular economies by creating financial incentives to produce renewable energy and return nutrients to agriculture. In this study, we characterize the potential for hydrothermal liquefaction (HTL)-based resource recovery systems to advance the economic and environmental sustainability of wastewater sludge, FOG (fats, oils, and grease), food waste, green waste, and animal manure management through the production of liquid biofuels (naphtha, diesel), fertilizers (struvite, ammonium sulfate), and power (heat, electricity). From the waste management perspective, median costs range from -193 $·tonne-1 (FOG) to 251 $·tonne-1 (green waste), and median carbon intensities range from 367 kg CO2 eq·tonne-1 (wastewater sludge) to 769 kg CO2 eq·tonne-1 (green waste). From the fuel production perspective, the minimum selling price of renewable diesel blendstocks are within the commercial diesel price range (2.37 to 5.81 $·gal-1) and have a lower carbon intensity than petroleum diesel (101 kg CO2 eq·MMBTU-1). Finally, through uncertainty analysis and Monte Carlo filtering, we set specific targets (i.e., achieve wastewater sludge-to-biocrude yield >0.440) for the future development of hydrothermal waste management system components. Overall, our work demonstrates the potential of HTL-based resource recovery systems to reduce the costs and carbon intensity of resource-rich organic wastes.

Microbiome science of human excrement composting

Linear waste management systems are unsustainable and contribute to environmental degradation, economic inequity, and health disparities. Among the array of environmental challenges stemming from anthropogenic impacts, the management of human excrement (human feces and urine) stands as a significant concern. Over two billion people do not have access to adequate sanitation, signifying a global public health crisis. Composting is the microbial biotechnology aimed at cycling organic waste, including human excrement, for improved public health, agricultural productivity and safety, and environmental sustainability. Applications of modern microbiome omics and related technologies have the capacity to support continued advances in composting science and praxis. In this article, we review literature focused on applications of microbiome technologies to study composting systems and reactions. The studies we survey generally fall into the categories of animal manure composting, biosolids composting, and human excrement composting. We review experiments utilizing microbiome technologies to investigate strategies for enhancing pathogen suppression and accelerating the biodegradation of organic matter. Additionally, we explore studies focused on the bioengineering potential of microbes as inoculants to facilitate degradation of toxins, such as pharmaceuticals or per- and polyfluoroalkyl substances. The findings from these studies underscore the importance of advancing our understanding of composting processes through the integration of emerging microbiome omics technologies. We conclude that work to-date has demonstrated exciting basic and applied science potential from studying compost microbiomes, with promising implications for enhancing global environmental sustainability and public health.

Preconceptional and in utero exposure of sheep to a real-life environmental chemical mixture disrupts key markers of energy metabolism in male offspring

Over recent decades, an extensive array of anthropogenic chemicals have entered the environment and have been implicated in the increased incidence of an array of diseases, including metabolic syndrome. The ubiquitous presence of these environmental chemicals (ECs) necessitates the use of real-life exposure models to the assess cumulative risk burden to metabolic health. Sheep that graze on biosolids-treated pastures are exposed to a real-life mixture of ECs such as phthalates, per- and polyfluoroalkyl substances, heavy metals, pharmaceuticals, pesticides, and metabolites thereof, and this EC exposure can result in metabolic disorders in their offspring. Using this model, we evaluated the effects of gestational exposure to a complex EC mixture on plasma triglyceride (TG) concentrations and metabolic and epigenetic regulatory genes in tissues key to energy regulation and storage, including the hypothalamus, liver, and adipose depots of 11-month-old male offspring. Our results demonstrated a binary effect of EC exposure on gene expression particularly in the hypothalamus. Principal component analysis revealed two subsets (B-S1 [n = 6] and B-S2 [n = 4]) within the biosolids group (B, n = 10), relative to the controls (C, n = 11). Changes in body weight, TG levels, and in gene expression in the hypothalamus, and visceral and subcutaneous fat were apparent between biosolid and control and the two subgroups of biosolids animals. These findings demonstrate that gestational exposure to an EC mixture results in differential regulation of metabolic processes in adult male offspring. Binary effects on hypothalamic gene expression and altered expression of lipid metabolism genes in visceral and subcutaneous fat, coupled with phenotypic outcomes, point to differences in individual susceptibility to EC exposure that could predispose vulnerable individuals to later metabolic dysfunction.

Feasibility of ammonium sulfate recovery from wastewater sludges: Hydrothermal liquefaction pathway vs. anaerobic digestion pathway

This study evaluated two pathways to recover the nitrogen-content of wastewater sludges as ammonium sulfate (AmS) for use as fertilizer. The first pathway entails sludge stabilization by hydrothermal liquefaction (HTL) followed by recovery of AmS from the resulting aqueous product by gas permeable membrane (GPM) separation. The second one entails stabilization of the sludges by anaerobic digestion (AD) followed by recovery of AmS from the resulting centrate by GPM separation. A bench-scale GPM reactor is shown to be capable of recovering >90% of N in the feed. Recoveries of NH3-N in the HTL-pathway ranged 96-100% in 5.5-7.5 h at mass removal rates of 0.2-0.3 g N/day, yielding 3.3-6.0 g AmS/L of feed. Recoveries of 98% were noted in the AD-pathway in 4 h at mass removal rates of 0.06-0.97 g N/day and a yield of 1.7-2.1 g AmS/L of feed. Inductively coupled plasma optical emission spectrometer analysis confirmed that both pathways yielded AmS meeting the US EPA and European region guidelines for land application. The GPM reactor enabled higher nitrogen-recoveries in the HTL-pathway than those reported for current practice of AD followed by ammonia stripping, ion exchange, reverse osmosis, and/or struvite precipitation (96-100% vs. 50-90%). A process model for the GPM reactor is validated using performance data on three different feedstocks.

A critical review on phycoremediation of pollutants from wastewater-a novel algae-based secondary treatment with the opportunities of production of value-added products

Though the biological treatment employing bacterial strains has wide application in effluent treatment plant, it has got several limitations. Researches hence while looking for alternative biological organisms that can be used for secondary treatment came up with the idea of using microalgae. Since then, a large number of microalgal/cyanobacterial strains have been identified that can efficiently remove pollutants from wastewater. Some researchers also found out that the algal biomass not only acts as a carbon sink by taking up carbon dioxide from the atmosphere and giving oxygen but also is a renewable source of several value-added products that can be extracted from it for the commercial use. In this work, the cleaning effect of different species of microalgae/cyanobacteria on wastewater from varied sources along with the value-added products obtained from the algal biomass as observed by researchers during the past few years are reviewed. While a number of review works in the field of phycoremediation technology was reported in literature, a comprehensive study on phycoremediation of wastewater from different industries and household individually is limited. In the present review work, the efficiency of diverse microalgal/cyanobacterial strains in treatment of wide range of industrial effluents along with municipal wastewater having multi-pollutants has been critically reviewed.

A critical review on nanoplastics and its future perspectives in the marine environment

Nanoplastics (plastic particles smaller than 1 μm) are the least-known type of marine litter. Nanoplastics (NPs) have attracted much interest in recent years because of their prevalence in the environment and the potential harm they can cause to living organisms. This article focuses on understanding NPs and their fate in the marine environment. Sources of NPs have been identified, including accidental release from products or through nano-fragmentation of larger plastic debris. As NPs have a high surface area, they may retain harmful compounds. The presence of harmful additives in NPs poses unique practical challenges for studies on their toxicity. In this review, several methods specifically adapted for the physical and chemical characterization of NPs have been discussed. Furthermore, the review provides an overview of the translocation and absorption of NPs into organisms, along with an evaluation of the release of potential toxins from NPs. Further, we have provided an overview about the existing methods suggested for the possible degradation of these NPs. We conclude that the hazards of NPs are plausible but unknown, necessitating a thorough examination of NPs' sources, fate, and effects to better mitigate and spread awareness about this emerging contaminant.

Sexually dimorphic impact of preconceptional and gestational exposure to a real-life environmental chemical mixture (biosolids) on offspring growth dynamics and puberty in sheep

Humans are ubiquitously exposed to complex mixtures of environmental chemicals (ECs). This study characterised changes in post-natal and peripubertal growth, and the activation of the reproductive axis, in male and female offspring of sheep exposed to a translationally relevant EC mixture (in biosolids), during pregnancy. Birthweight in both sexes was unaffected by gestational biosolids exposure. In contrast to females (unaffected), bodyweight in biosolids males was significantly lower than controls across the peripubertal period, however, they exhibited catch-up growth eventually surpassing controls. Despite weighing less, testosterone concentrations were elevated earlier, indicative of early puberty in the biosolids males. This contrasted with females in which the mean date of puberty (first progesterone cycle) was delayed. These results demonstrate that developmental EC-mixture exposure has sexually dimorphic effects on growth, puberty and the relationship between body size and puberty. Such programmed metabolic/reproductive effects could have significant impacts on human health and wellbeing.

What affects the accuracy and applicability of determining wastewater sludge water content via low-field nuclear magnetic resonance?

The accurate determination of waster sludge water content is crucial to sludge dewatering treatment and its disposal management. Though previous studies highlight the great advantages of low-field nuclear magnetic resonance (LF-NMR) in the determination of sludge water content, its accuracy and applicability are not well studied. Herein, this study investigated the settling of operating parameters and the properties of sludge samples on the accuracy and applicability of LF-NMR method in measuring sludge water content. The results showed that the setting of basic parameters such as standard curve, number of scanning times (NS) and sample weight affected the accuracy of sludge water content by LF-NMR. The standard calibration curve constructed by 3 g/L CuSO₄, NS = 8 and the sample weight of about 5 g, were suitable for the accurate determination of sludge water content. Furthermore, the existence of magnetic substances in sludge can affect the distribution gradient of main magnetic field, and thus restricted the applicability of LF-NMR. The saturation magnetization of chemical reagents strongly correlated with the measured relative errors of sludge water content (r = 0.995, p < 0.01), the greater the saturation magnetization of the magnetic material, the greater the error of the test results. On the whole, it is necessary to fully consider the influence of process parameters and sludge properties to evaluate the accuracy and applicability of the LF-NMR method, rather than simply copying the parameters in literatures.

Highly-efficient degradation of organic pollutants by oxalic acid modified sludge biochar: Mechanism and pathways

The application of sludge biochar (SC) materials as efficient catalysts for organic pollutants mineralization via advanced oxidation process meets the good strategy of "make waste profitable". The catalytic oxidations of methyl orange (MO) and pyrene by oxalic acid modified sludge biochar (SC-OA) with and without H₂O₂ were carried out. The analysis of Fourier transform infrared (FT-IR), X-ray photoelectron spectroscopy (XPS), electronic paramagnetic resonance spectrometer (EPR) and free radical quenching experiment were performed and the definite relationships between persistent free radicals (PFRs) type and specific reactive oxygen species (ROS) were made clear. It is suggested for the first time that carbon-centered type PFRs in SC-OA without H₂O₂ could form O₂•^- and •OH from COOH groups, while oxygen-centered type PFRs induced H₂O₂ to produce •OH. The degradation intermediates of MO and pyrene were identified and the transformation pathways were proposed. SC-OA, possessing good sustainable utilization and clean catalytic property, is expected to be popularized and applied in the mineralization of organic pollutants, especially in the in-situ remediation of contaminated soil where is no continuous supply of H₂O₂.

Towards advanced simultaneous nitrogen removal and phosphorus recovery from digestion effluent based on anammox-hydroxyapatite (HAP) process: Focusing on a solution perspective

In this paper, the state-of-the-art information on the anammox-HAP process is summarized. The mechanism of this process is systematically expounded, the enhancement of anammox retention by HAP precipitation and the upgrade of phosphorus recovery by anammox process are clarified. However, this process still faces several challenges, especially how to deal with the ∼ 11% nitrogen residues and to purify the recovered HAP. For the first time, an anaerobic fermentation (AF) combined with partial denitrification (PD) and anammox-HAP (AF-PD-Anammox-HAP) process is proposed to overcome the challenges. By AF of the organic impurities of the anammox-HAP granular sludge, organic acid is produced to be used as carbon source for PD to remove the nitrogen residues. Simultaneously, pH of the solution drops, which promotes the dissolution of some inorganic purities such as CaCO₃. In this way, not only the inorganic impurities are removed, but the inorganic carbon is supplied for anammox bacteria.

Hydrothermal liquefaction of sewage sludge anaerobic digestate for bio-oil production: Screening the effects of temperature, residence time and KOH catalyst

Due to sewage sludge being an abundant biobased resource, and with the number of biogas plants utilizing sewage sludge increasing, digested sewage sludge (DSS) is a promising feedstock for producing bio-oil. This study uses DSS from a biogas plant to produce bio-oil in a hydrothermal liquefaction process adjusting time from 2 to 6 hours, temperature from 280 to 380°C and the presence of a base as a depolymerization agent and potential catalyst. High conversion yields are obtained, with the maximum of 58 wt% on a dry, ash free basis and an energy recovery of up to 94%. The oils contain compounds with a potential for utilization as biofuels and building blocks, especially fatty acids as biodiesel feedstock and biobased phenols, glycols and aliphatic alcohols.

Towards the carbon neutrality of sludge treatment and disposal in China: A nationwide analysis based on life cycle assessment and scenario discovery

Motivated by the carbon neutrality target, strategic planning for a low-carbon transition of sludge treatment and disposal in China is challenging due to the unpredictability of technical, regional, socioeconomic, and political factors affecting greenhouse gas (GHG) emissions. This study combines the use of a Life Cycle Assessment and the Patient Rule Induction Method, accounting for possibilities that could achieve net-zero carbon emissions by exploring multiple plausible future profiles of sludge treatment and disposal. Results show that reducing sludge landfill and increasing anaerobic digestion are effective methods to facilitate GHG reduction. Achieving carbon neutrality is closely linked to developing a cleaner electricity mix. Based on a cascaded scenario analysis considering regional differences for 31 Chinese provinces, results demonstrated a maximum cumulative reduction potential of 371 Mt CO2 equivalents from 2020 to 2050, equal to 59.84% of the business-as-usual scenario. Together with GHG reductions, terrestrial acidification and ecotoxicity as well as freshwater ecotoxicity are synergistically reduced. However, the shifting environmental burden results in freshwater eutrophication, human toxicity, marine ecotoxicity, marine eutrophication, and photochemical oxidant formation. This study presents a novel method for systematically identifying possible future development paths toward carbon neutrality. The findings may support policy designs for achieving target carbon reduction effects for sludge disposal.

Sludge disintegration and phosphorus migration in anaerobic fermentation of waste activated sludge by the addition of EDTA-2Na

The effects of the addition of EDTA-2Na on sludge disintegration and phosphorus (P) migration during anaerobic fermentation (AF) of waste activated sludge (WAS) are investigated. The efficiency of sludge disintegration was positively correlated with the dose of EDTA-2Na from 0.5-2.0 g/g SS, and an enormous quantity of P was liberated into the aqueous phase, accompanied by sludge disintegration. The proper dose of EDTA-2Na for P release from WAS was 1.5 g/g SS, with an orthophosphate concentration of 394.72 mg/L. P release was more consistent with the pseudo second-order kinetic model. The migration of P species during AF with EDTA-2Na addition was also studied. Orthophosphate was the main species in both of the liquid phase and the loosely bound extracellular polymeric substances (EPS), but organic P (OP) was much more abundant in tightly bound EPS. Inorganic P (IP) was the dominant P speciation in the solid and was mainly distributed in the fraction of non-apatite IP, which accounted for more than 62.8% of IP in the presence of EDTA-2Na. In addition, both IP and OP in the solid contributed to the accumulation of P and the former was outperformed. Furthermore, the increased total dissolved P mainly came from cells. However, the fermented sludge tended to be smaller and to have low compressibility, which is detrimental to its further treatment.

Heavy metals accumulation in wheat (Triticum aestivum L.) roots and shoots grown in calcareous soils treated with non-spiked and spiked sewage sludge

With growing urbanization and agriculture, the quantity of sewage sludge production increases every year. For the purpose of risk management, it is crucial to figure out how much heavy metals are transported to different parts of plants when sewage sludge is used. A greenhouse experiment was carried out to investigate the accumulation of heavy metals in wheat (Triticum aestivum L.) grown in 30 calcareous soils. The soils in this study were subjected to three different treatments: soils treated with sewage sludge at a rate of 2.5%, soils treated with sewage sludge at a rate of 2.5% and enriched with heavy metals, and control soils that received neither sewage sludge nor heavy metals. Wheat grown in sewage sludge-treated soils had the highest mean dry matter, and was 2.11 and 1.25 times greater than wheat grown in control and spiked-sewage sludge-treated soils, respectively. In all treatments, wheat roots had greater heavy metal levels than wheat shoots. Among all the heavy metals examined, Pb and Cu had the highest bioconcentration factors for roots and shoots (BCF_Roots and BCF_Shoots) in control and sewage sludge-treated soils, followed by Cd in spiked-sewage sludge-treated soils, and Co and Ni had the lowest BCF_Roots and BCF_Shoots across all treatments. In spiked-sewage sludge-treated soils, the root restriction for heavy metals translocation was more important for Co, Cu, and Ni than for Pb and Zn, indicating that wheat can be grown safely in a variety of calcareous soils amended with sewage sludge with high content of Cd, Co, Cu, and Ni. Reducing the transfer of Pb and Zn from soils to wheat in soils treated with sewage sludge yet having high concentrations of these heavy metals should be considered as a top priority strategy for preserving wheat products. Since a wide range of calcareous soils was used in this study and because calcareous soils make up the majority of soils in the Middle East, the findings are relevant for all of the countries in this region.

Closing the Nutrient Loop-The New Approaches to Recovering Biomass Minerals during the Biorefinery Processes

The recovery of plant mineral nutrients from the bio-based value chains is essential for a sustainable, circular bioeconomy, wherein resources are (re)used sustainably. The widest used approach is to recover plant nutrients on the last stage of biomass utilization processes-e.g., from ash, wastewater, or anaerobic digestate. The best approach is to recover mineral nutrients from the initial stages of biomass biorefinery, especially during biomass pre-treatments. Our paper aims to evaluate the nutrient recovery solutions from a trans-sectorial perspective, including biomass processing and the agricultural use of recovered nutrients. Several solutions integrated with the biomass pre-treatment stage, such as leaching/bioleaching, recovery from pre-treatment neoteric solvents, ionic liquids (ILs), and deep eutectic solvents (DESs) or integrated with hydrothermal treatments are discussed. Reducing mineral contents on silicon, phosphorus, and nitrogen biomass before the core biorefinery processes improves processability and yield and reduces corrosion and fouling effects. The recovered minerals are used as bio-based fertilizers or as silica-based plant biostimulants, with economic and environmental benefits.

A novel dual circulating fluidized bed technology for thermal treatment of municipal sewage sludge with recovery of nutrients and energy

Sewage sludge (SS), a by-product of the wastewater treatment process, should be viewed not as waste, but as a potential resource for renewable energy and nutrient recovery. However, SS contains various toxic and harmful pollutants, e.g., pathogens, pharmaceutical residues, and microplastics. Through organic recycling and reuse of SS on land, these contaminants may leak into the environment, creating potential hazards to the ecosystem and human health. To tackle this issue, an advanced SS treatment technique within circular economy principles was proposed. In this process, mechanically dewatered SS with 20-25 % total solids is first dried at 110 °C in a circulating fluidized bed dryer and then combusted at 850 °C in a circulating fluidized bed reactor. Consequently, all the unwanted organic compounds are eliminated, and the ash - relatively high in nutrients and sufficiently low in heavy metals - can be further processed into fertilizers and used in forestry or farming. Moreover, the process is self-sufficient in terms of energy, enabling standalone operation without supplementary fuels, and providing excess heat that can be utilized, e.g., as district heat. This paper describes the process in detail and reviews experiences and lessons learned from the commissioning and trial operation of a newly erected 1.5 MW_th sludge combustion plant with a throughput of 10 000 t/a. The operational performance of the plant has been verified based on continuous processing of dewatered SS, and the main operating parameters were consistent with design values. Therefore, the scale-up of this technique was considered both feasible and successful.

Revealing the mechanisms of polypyrrole (Ppy) enhancing methane production from anaerobic digestion of waste activated sludge (WAS)

Anaerobic digestion (AD) is a promising method for treating waste activated sludge (WAS), but the low methane yield limits its large-scale application. The addition of conductive nanomaterials has been demonstrated to enhance the activity of AD via promoting the direct interspecies electron transfer (DIET). In this study, novel conductive polypyrrole (Ppy) was prepared to effectively improve the AD performance of WAS. The results showed that the accumulative methane production was enhanced by 27.83% by Ppy, with both acidogenesis and methanogenesis being efficiently accelerated. The microbial community analysis indicated that the abundance of bacteria associated with acidogenesis process was significantly elevated by Ppy. Further investigation by metatranscriptomics revealed that fadE and fadN genes (to express the key enzymes in fatty acid metabolism) were highly expressed in the Ppy-driven AD, suggesting that Ppy promoted electron generation during acid production. For methanogenesis metabolism, genes related to acetate utilization and CO₂ utilization methanogenesis were also up-regulated by Ppy, illustrating that Ppy facilitates the utilization of acetate and electrons by methanogenic archaea, thus potentially promoting the methanogenesis through DIET.

Ecological risk assessment of toxic metal(loid)s for land application of sewage sludge in China

Sewage sludge, including those after biological or thermochemical treatments, has the potential to be used as fertilizers for recycle of resources. However, its potential ecological risk is also of great concern to policy making. This study employed comprehensive ecological risk assessment (ERA) methods to evaluate the risk caused by the toxic metal(loid)s in sewage sludge throughout China. The conventional geo-accumulation index and potential ecological risk index revealed that cadmium (Cd) and mercury (Hg) were of significant concern in treating sewage sludge before land application, but chromium (Cr) and zinc (Zn) were preferred by potential affected proportion (PAF) and overall risk probability (ORP) of species sensitivity distribution (SSD). Because SSD considered both the community and the ecotoxicity of toxic metal(loid)s, it was more advantageous and promising in assessing ecological risks caused by land application of sewage sludge. Based on the predicted no-effect concentration (PNEC) of toxic metal(loid) calculated by hazardous concentration that cause death of 50% of species (HC50) by SSD, the maximum allowable disposal amount (MADA) of sewage sludge in the whole China indicated that chromium (Cr) should be totally eliminated because of its high risks in the present background soil. After excluding Cr, the MADA of sewage sludge in China was 3.24 × 10⁶ t and 6.47 × 10⁷ t under land application scenarios with high and low ecological risks, respectively. Additionally, the MADA could be increased by mixing sewage sludge with deeper soil in wider areas. This study emphasized that local laws and regulations on land application of sewage sludge and the subsequent ERA system need to be addressed in the future.

Carbon quantum dots: An environmentally friendly and valued approach to sludge disposal

Sewage sludge, produced daily and inherent to urban development, presents problems of disposal that are still challenging today. Its disposal still offers palliative solutions, where the final destination is generally in landfills or, restrictively, to use in agriculture. The synthesis of carbon quantum dots (CQDs) from sewage sludge is a better alternative to use the stock of organic material present in the sludge. The present work aims to produce Carbon quantum dots (CQDs) using principles of green chemistry and to use an alternative raw material intrinsic stock of carbon present in sewage sludge, making its final disposal more sustainable. The material obtained has a core structure mainly composed of sp2 carbon and nitrogen. The surface functional groups containing sulfur, nitrogen, and oxygen of CQDs were investigated using FTIR and TG/DSC coupled FTIR techniques. The CQDs showed a luminescence decay time equivalent to fluorescent compounds and with satisfying quantum yield since no passive/oxidizing agent or material purification process was used. The photoluminescence spectroscopy analysis showed that the CDQs excitation λmax was at 360 nm and caused a λmax emission at 437 nm (CQDsa) and 430 nm (CQDsb). The CQDs obtained showed sizes of 9.69 ± 2.64 nm (CQDsa) and 10.92 ± 2.69 nm (CQDsb). In vitro experiments demonstrated the uptake of CQDs by the endothelial cell line EAhy 926 and their nontoxicity. However, the production of CQDs can be used for the sustainable disposal of sewage sludge.

Removal of heavy metals from sewage sludge by chemical leaching with biodegradable chelator methyl glycine diacetic acid

The heavy metals (HMs) contained in sewage sludge are some of the largest obstacles that hamper the usage of sewage sludge in land application (e.g. fertilizer, soil improver). The conventional chelators, e.g., ethylenediaminetetraacetic acid (EDTA), were effective in the remediation of HMs polluted sewage sludge, but suffered from an evident drawback of low biodegradability. Therefore, the applicability of a new biodegradable chelator, methyl glycine diacetic acid (MGDA), to extract HMs from sewage sludge was carried out and compared with EDTA. The experimental parameters affecting the performance of MGDA were optimized. Leaching results showed that in general, MGDA exhibited higher Zn leaching efficiency and similar Cu, Ni and Cr leaching efficiencies with EDTA at same pH and dosage conditions. The maximum Zn, Cu, Ni and Cr leaching efficiencies of MGDA were 94.1% ± 4.5%, 58.2% ± 3.1%, 78.2% ± 2.3% and 54.6% ± 2.5%, respectively. The leaching efficiency plateaued within a reaction time of 4 h, but that of Cu and Ni showed a slightly decreasing trend during hours 4 to 10. In raw sewage sludge, the Zn and Cu were mainly presented in the organically bound fraction, i.e., 45.3 ± 3.2% of total Zn and 48.3 ± 1.4% of total Cu. The addition of MGDA and EDTA caused obvious distribution transformations in Zn and Cu from the organically bound fraction to soluble fraction. According to the reduced partition index calculation, the mobility of Zn, Cu, Ni, and Cr was not significantly lowered after the MGDA treatment. However, the HMs secondary pollution risk of the sludge was reduced due to the drop of the total HMs content after chelator leaching. Findings from this study suggest that MGDA could be a potential environment-friendly alternative for refractory chelators (e.g. EDTA) in the decontamination of HMs from sludge.

The changes of microplastics' behavior in adsorption and anaerobic digestion of waste activated sludge induced by hydrothermal pretreatment

Waste activated sludge (WAS) contains high concentrations of microplastics (MPs), which could serve as vectors of various organic pollutants and heavy metals, causing synergistic transportation and pollution. The application of combined hydrothermal pretreatment (HTP) and anaerobic digestion (AD) has raised growing concerns since the low-temperature hydrothermal treatment could enhance the biogas production of WAS. However, the changes in physicochemical properties, adsorption performances, and effects on AD of MPs by HTP have not been studied. The study used three typical MPs in WAS, and it was found that the HTP (170°C & 30min) increased MPs' specific surface area and carbonyl index (CI) while decreasing the relative crystallinity. The adsorption capacity to Cd increased through the carbonylation for polyethylene microplastic (PE-MP) and polystyrene microplastic (PS-MP) while decreasing by the dechlorination for polyvinyl chloride microplastic (PVC-MP). Meanwhile, increased hydrophilicity reduced the adsorption capacities of all three typical MPs for ofloxacin. The above results indicated that the HTP could be worth blocking the adsorption of polar MPs for polar pollutants. For the pristine MPs, only PVC-MP at the highest concentration (0.5 g kg^-1 VS) significantly (p < 0.05) reduced methane production by 16.2 ± 3.3% of WAS without the HTP. However, the HTP resulted in significant (p < 0.05) inhibition of methane production of WAS at high concentrations of PE-MP and PVC-MP (e.g., 0.1 and 0.5 g kg^-1 VS), which was due to the acceleration of the released toxic plastic additives (dibutyl phthalate, dimethyl phthalate, and bisphenol-A). Microbial analysis showed the abundances of vital anaerobes, such as acid-producing bacteria (Acetoanerrobium and Mesotoga), proteolytic bacteria (Proteiniborus), and methanogens (Methanosaeta) clearly decreased with the PE-MP and PVC-MP after the HTP, which might result in the decreased methane production. The study provided deep-insight of MPs' behaviors during the combined HTP-AD process.

Combining sequential extraction and 3D fluorescence to investigate the behavior of antibiotic and polycyclic aromatic hydrocarbons during solar drying of sewage sludge

Solar drying and liming are commonly used for sludge treatment, but little is known about their efficiency on antibiotics and Polycyclic Aromatic Hydrocarbons (PAHs) removal. This study aimed to investigate the removal of antibiotics and PAHs during solar drying of Limed Sludge (LS) and Non-Limed Sludge (NLS). Thus, organic matter fractionation and 3D fluorescence were used to assess the accessibility and the complexity of organic matter. 2 experiments have been conducted using LS and NLS for 45 days of drying in a pilot scale tunnel. Physicochemical results indicated significant decrease of water content (90%) for both sludge samples within 15 days of drying. For both treatments, the removal of total organic carbon and total nitrogen was low and similar for both treatments. Through this study, it has been confirmed that liming and drying contributed to a strong modification of the organic matter quality with an increase of its accessibility. On the other hand, drying alone increased the less accessible compartments, while the presence of lime affected the interconnexion between the organic matter pools. 3D fluorescence confirmed the obtained results and indicated that LS leads to obtaining more simple molecules in the most accessible compartments, while NLS leads to obtaining more complex molecules in the less accessible compartments. In addition, solar radiations and leaching may contribute to the significant removal (p < 0.01) of roxithromycin, benzo(a)anthracene, chrysene, benzo[k]fluoranthene, benzo[a]pyrene, and benzo(g, h, i) perylene in the presence of lime. Furthermore, the evolution of organic matter pools in terms of accessibility and complexity may drive the bioavailability of these pollutants, leading to their significant removal.

Review of Clay-Based Nanocomposites as Adsorbents for the Removal of Heavy Metals

Due to rapid industrialization, urbanization, and surge in modern human activities, water contamination is a major threat to humanity globally. Contaminants ranging from organic compounds, dyes, to inorganic heavy metals have been of major concern in recent years. This necessitates the development of affordable water remediation technologies to improve water quality. There is a growing interest in nanotechnology recently because of its application in eco-friendly, cost-effective, and durable material production. This study presents a review of recent nanocomposite technologies based on clay, applied in the removal of heavy metals from wastewater, and highlights the shortcomings of existing methods. Recently published reports, articles, and papers on clay-based nanocomposites for the removal of heavy metals have been reviewed. Currently, the most common methods utilized in the removal of heavy metals are reverse osmosis, electrodialysis, ion exchange, and activated carbon. These methods, however, suffer major shortcomings such as inefficiency when trace amounts of contaminant are involved, uneconomical costs of operation and maintenance, and production of contaminated sludge. The abundance of clay on the Earth’s surface and the ease of modification to improve adsorption capabilities have made it a viable candidate for the synthesis of nanocomposites. Organoclay nanocomposites such as polyacrylamide-bentonite, polyaniline-montmorillonite, and β-cyclodextrin-bentonite have been synthesized for the selective removal of various heavy metals such as Cu2+, Co2+, among others. Bacterial clay nanocomposites such as E. coli kaolinite nanocomposites have also been successfully synthesized and applied in the removal of heavy metals. Low-cost nanocomposites of clay using biopolymers like chitosan and cellulose are especially in demand due to the cumulative abundance of these materials in the environment. A comparative analysis of different synthetic processes to efficiently remove heavy metal contaminants with clay-based nanocomposite adsorbents is made.

Beyond Traditional Energy Sector Coupling: Conserving and Efficient Use of Local Resources

Decentralisation and sector coupling are becoming increasingly crucial for the decarbonisation of the energy system. Resources such as waste and water have high energy recovery potential and are required as inputs for various conversion technologies; however, waste and water have not yet been considered in sector coupling approaches but only in separate examinations. In this work, an open-source sector coupling optimisation model considering all of these resources and their utilisation is developed and applied in a test-bed in an Israeli city. Our investigations include an impact assessment of energy recovery and resource utilisation in the transition to a hydrogen economy, with regard to the inclusion of greywater and consideration of emissions. Additionally, sensitivity analyses are performed in order to assess the complexity level of energy recovery. The results demonstrate that waste and water energy recovery can provide high contributions to energy generation. Furthermore, greywater use can be vital to cover the water demands in scarcity periods, thus saving potable water and enabling the use of technology. Regarding the transition to hydrogen technologies, resource energy recovery and management have an even higher effect than in the original setup. However, without appropriate resource management, a reduction in emissions cannot be achieved. Furthermore, the sensitivity analyses indicate the existence of complex relationships between energy recovery technologies and other energy system operations.

Systematic understanding of char-volatile evolution and interaction mechanism during sewage sludge pyrolysis through in-situ tracking solid-state reaction and products fate

The complexity of sludge components and the heterogeneity of pyrolysis products make it challenging to trace char-volatile evolutions and interaction mechanisms during pyrolysis. Herein, we systematically dissected the solid-state reactions and volatile dynamic variations via in-situ infrared/mass spectral probes coupled signal amplification techniques. The identification of hidden reactions was further enhanced by comparing the discrepancies in the pyrolysis of three systems: raw sludge, sludge-extracted organics, and pseudo-components of organics. A three-stage sludge pyrolysis of bond cleavage (α = 0.2-0.5), intermediates diffusion (α = 0.5-0.7), and interface interaction (α = 0.7-0.8) was proposed through solid-state reaction tracing, and the pyrolysis reaction was found to be dominated by the first two stages. The generation of reactive intermediates accelerated the collision frequency between reactants, which increased the order of solid-state reactions and raised the energy barrier from 148 to 180-261-297 kJ/mol. The temperature-response sequence of the major pyrolysis volatiles was H₂O/CO₂/furans/alcohols (<250 °C), amine-N/acids/ketones/esters (250-350 °C), heterocyclic-N/phenols/C_2-3 (300-400 °C), CH₄/aromatics/nitrile-N (350-450 °C), and CO/HCN (>450 °C). The temperature-dependent evolution of these volatiles was consistent with the variations of chars in terms of pyrolysis behaviors, reaction models, and surface characteristics. The comprehensive understanding of the staged pyrolysis pathways and the char-volatile interaction mechanisms may provide critical information for pyrolysis procedure design and product targeted regulation.

Analysis of the Effect of Sludge Reduction and Energy Production from Introducing Anaerobic Digest Plant into a Sewage Treatment Plant

As the amount of sewage sludge (SS) is increasing worldwide, anaerobic digesters (ADP) are being distributed to reduce it and treat it in an environmentally friendly way. In Korea, 20 years have passed since the introduction of ADP, but the number of sewage treatment plants (STP) installed with ADP is only about 10% of the total STP. Accordingly, problems and improvements were examined through material flow analysis targeting STP, and the effect of introducing anaerobic digestion (AD) was analyzed as a way to solve them. As a result of the analysis, the amount of SS generated by the STP (SS-ADP + Co-ADP) installed and operated by an AD was 0.54 kg/m3, and the facility without it was 0.77 kg/m3, showing a reduction effect of about 31%. The SS reduction effect of the facility that only used SS-AD was found to be reduced by 21–24% TOE (Ton Of Equivalent))/day, which has the effect of reducing 794,867 kg-CO2/day of greenhouse gas. In terms of energy efficiency, Co-AD was 86% higher than SS-AD, and biogas production yield was 90% higher than that of SS-AD. Therefore, it is necessary to introduce Co-AD into STP in terms of reducing SS, energy production, and greenhouse gas reduction.

Unraveling the behaviors of sulfonamide antibiotics on the production of short-chain fatty acids by anaerobic fermentation from waste activated sludge and the microbial ecological mechanism

Antibiotics in waste activated sludge (WAS) has drawn increasing attention because of their persistent and bioaccumulation characteristics. Most study illustrated the role of antibiotics in anaerobic fermentation from WAS, but lacking the analysis at microbial level as well as the possible interaction between them. This study investigated the effect of three sulfonamide antibiotics (sulfamethoxazole (SMX), sulfaquinoxaline (SQX), and sulfadiazine (SD)) on WAS fermentation and explored its microbiological mechanism. Results indicated that the production of short-chain fatty acids (SCFAs) was significantly improved by 1.9 folds with a peak value at 4626.1 mg COD L^-1 in the existence of SD. This was attributed to the promoted release of soluble proteins and polysaccharides with the existence of sulfonamide antibiotics (SAs) as revealed by the excitation-emission matrix (EEM) spectrum. Analysis of microbial community structure showed that the total abundance of the fermenters in groups with SAs was1.2-1.6 times of that in Control. Specifically, the acid-forming genus Tissierella in SMX and SQX increased by 12.1%-15.0% compared with the Control, while the proteolytic genus Proteinivorax dominated in SD with 39.5%. Molecular ecological networks (MENs) analysis further revealed the potential cooperative relationships among different fermenters. This study was anticipated to provide some valuable information for the behavior of antibiotics in WAS fermentation.

The Analysis of the Conceptual Framework of Green Port Implementation in Indonesia Using Circular Economy: The Case Study of Benoa Public and Fishing Terminals

Several public seaports and fishing terminals are located in the same port complex but have different fragmented operations such as waste management. It is possible to provide a new initiative to ensure sustainability for all entities in the surrounding port ecosystem through the application of Green Port using the circular economy approach and mixed linear programming model. Therefore, this study aims to explore the collaborative management of waste generated from different port activities such as the operators of the public seaport, fishing terminal, and a city authority in Bali–Indonesia using circular economy principles. It was discovered that the integration model has the potential to generate new energy by recycling waste from all related entities in the production of a few main fishing products such as tuna, sardine, and squid, as well as vessel traffic, facilities, and cargo flow interactions in addition to other port operations.

Effects of sewage sludge pretreatment methods on its use in agricultural applications

Pretreatment is widely used in sludge dewatering, however, its potentially impact on the subsequent sludge agricultural applications is often neglected. Here, the potential benefits and risks of the sludge with no pretreatment and with four most commonly used pretreatment methods in sludge agricultural applications were assessed using potted lettuce, an experimental crop. The results show that sewage sludge pretreatment methods can greatly affect its agricultural applications. The application of different pretreatment methods can potentially reduce the harm caused by pathogens. At low dosage (0.2 g kg^-1), different sludge fertilizers promoted an increase in crop yield of 14.6% to 49.1%, and the concentrations of heavy metals in the crop and soil were controlled within safe ranges. At high dosage (8 g kg^-1), crop yield using pretreated sludge (except anaerobic digestion) decreased by between 32.7% and 57.5%, but heavy metal pollution of both crop and soil increased. In terms of promoting crop growth and reducing heavy metal accumulation, untreated sludge was better than pretreated sludges and sludge with physical pretreatments was better than that with chemical pretreatments. Overall, this study clearly shows that the introduction of pretreatment in sludge dewatering can inevitably impact its agricultural land application.

Using biochar to strengthen the removal of antibiotic resistance genes: Performance and mechanism

In this study, the excess activated sludge was used for pyrolysis to produce biochar with Ce modification. The removal process and mechanism of ampicillin resistance gene (ARG_Amp) by biochar was investigated. The results showed that when pyrolyzing the excess sludge at 400 °C, the organic components in the sludge could be partially pyrolyzed and complexed with Ce. By accepting electrons from phenol or quinone, persistent free radicals (PFRs) were formed on the surface of biochar. On the optimized conditions with the initial ARG_Amp concentration of 41.43 mg/L, the removal ratios of ARG_Amp by adsorption, PFRs, hydroxyl free radicals (·OH) by adding H₂O₂ were 28.37%, 8.26%, and 27.56%. No melted DNA was detected in the treated samples. The oxidation process by PFRs and ·OH can directly destroy the ARG_Amp structure. The phosphodiester bond in the base stacking structure and the phosphate bond in the nucleotide are the possible action sites of PFRs. Treated ARG_Amp products were in the form of base pair residues or short-chain double helix structures. ·OH can be added to the bases of nucleotide molecules to form highly active free radical adducts. They can initiate molecular dehydrogenation and intermolecular proton transfer, resulting in oxidation of the base to the scission of the phosphate sugar backbone.

Pilot-scale demonstration of a novel process integrating Partial Nitritation with simultaneous Anammox, Denitrification and Sludge Fermentation (PN + ADSF) for nitrogen removal and sludge reduction

Anammox process is a cost-effective solution for nitrogen removal, whereas unsatisfactory effluent with nitrate accumulation is usually achieved in treating domestic sewage, owning to the unwanted prevalence of nitrite-oxidizing bacteria (NOB) and the intrinsic nitrate production by anammox bacteria. Herein, a pilot-scale system integrating Partial Nitritation and simultaneous Anammox, Denitrification and Sludge Fermentation (PN + ADSF) process was developed to treat real municipal wastewater. In this process, PN was accomplished in a sequencing batch reactor (SBR) using the strategy of intermittent hydroxylamine addition, while ADSF coupling anammox and heterotrophic denitrification was conducted in an up-flow anaerobic sludge blanket reactor (UASB) to further remove nitrogen. The pilot-scale system achieved total inorganic nitrogen (TIN) concentrations of 10.0 mg N/L in effluent and sludge reduction efficiency of 42.3% simultaneously. The characterization on microbial communities revealed that Candidatus Kuenenia and Thauera were the dominant functional bacteria for anammox and denitrification, respectively. Supported by the slow-release carbon sources from sludge fermentation, heterotrophic denitrification contributed to about 28% of nitrogen removed from the UASB, while anammox played a more important role in nitrogen removal. The pilot-scale demonstration confirmed that the PN + ADSF process is technically feasible for enhanced nitrogen removal and sludge reduction.

Resin-Mediated pH Control of Metal-Loaded Ligand Exchangers for Selective Nitrogen Recovery from Wastewaters

Highly selective separation materials that recover total ammonia nitrogen (i.e., ammonia plus ammonium, or TAN) from wastewaters as a pure product can supplement energy-intensive ammonia production and incentivize pollution mitigation. We recently demonstrated that commercial acrylate cation exchange polymer resins loaded with transition metal cations, or metal-loaded ligand exchangers, can recover TAN from wastewater with high selectivity (TAN/K+ equilibrium selectivity of 10.1) via metal-ammine bond formation. However, the TAN adsorption efficiency required further improvement (35%), and the optimal concentration and pH ranges were limited by both low ammonia fractions and an insufficiently strong resin carboxylate-metal bond that caused metal elution. To overcome these deficiencies, we used a zinc-acrylate ligand exchange resin and a tertiary amine acrylic weak base resin (pH buffer resin) together to achieve resin-mediated pH control for optimal adsorption conditions. The high buffer capacity around pH 9 facilitated gains in the adsorbed TAN per ligand resin mass that enhanced the TAN adsorption efficiency to greater than 90%, and constrained zinc elution (below 0.01% up to 1 M TAN) because of decreased ammonia competition for zinc-carboxylate bonds. During TAN recovery, resin-mediated pH buffering facilitated recovery of greater than 99% of adsorbed TAN with 0.2% zinc elution, holding the pH low enough to favor ammonium but high enough to prevent carboxylate protonation. For selective ion separation, solid phase buffers outperform aqueous buffers because the initial solution pH, the buffering capacity, and the ion purity can be independently controlled. Finally, because preserving the resin-zinc bond is crucial to sustained ligand exchange performance, the properties of an ideal ligand resin functional group were investigated to improve the properties beyond those of carboxylate. Ultimately, ligand exchange adsorbents combined with solid pH buffers can advance the selective recovery of nitrogen and potentially other solutes from wastewaters.

Mercury emission profile for the torrefaction of sewage sludge at a full-scale plant and application of polymer sorbent

We evaluated mercury (Hg) behavior in a full-scale sewage sludge torrefaction plant with a capacity of 150 wet tons/day, which operates under a nitrogen atmosphere at a temperature range of 250-350 °C. Thermodynamic calculations and monitoring results show that elemental Hg (Hg⁰) was the dominant species in both the pyrolysis gas during the torrefaction stage and in the flue gas from downstream air pollution control devices. A wet scrubber (WS) effectively removed oxidized Hg from the flue gas and moved Hg to wastewater, and an electrostatic precipitator (ESP) removed significant particulate-bound Hg but showed a limited capacity for overall Hg removal. Hg bound to total suspended solids had a much higher concentration than that of dissolved Hg in wastewater. Total suspended solid removal from wastewater is therefore recommended to reduce Hg discharge. Existing air pollution control devices, which consist of a cyclone, WS, and ESP, are not sufficient for Hg removal due to the poor Hg⁰ removal performance of the WS and ESP; a further Hg⁰ removal unit is necessary. A commercial packed tower with sorbent polymer catalyst composite material was effective in removing Hg (83.3%) during sludge torrefaction.