Non-Target and Suspect Screening of Per- and Polyfluoroalkyl Substances in Airborne Particulate Matter in China

Levels and transport behavior of ionic per- and polyfluoroalkyl substances in the atmosphere of urban pollution scenario: An in-situ investigation of a wastewater treatment plant in Wuxi, China

The levels of ionic per- and polyfluoroalkyl substances (iPFASs) in atmospheric particulate matter (PM2.5), wastewater, and aqueous aerosol collected at a municipal WWTP in Wuxi were investigated. The concentration of Σ20iPFASs in PM2.5 collected from the WWTP (72.2 pg/m3, monthly average) was slightly higher than that from the control point (58.4 pg/m3). Furthermore, the HYSPLIT model implied that the iPFASs pathways of control point and WWTP were totally different under identical meteorological conditions and that WWTP could be a source of iPFASs in urban environment. A comparison of the levels and compositions of iPFASs in aeration tank wastewater (203 ± 118 ng/L), effluent (392 ± 145 ng/L), and aqueous aerosols (58.5 ± 11.7 ng/L) samples using the t-stochastic neighborhood embedding algorithm revealed similar pollution fingerprints in aqueous aerosols and aeration tank wastewater, which implied that aqueous aerosols could be originating from the aeration tanks of WWTP and that aqueous aerosols may serve as a carrier for the transport of iPFASs from wastewater to atmosphere. Forward trajectory analysis indicated that the priority contaminated areas were more than 200 km southeast of the WWTP source, suggesting that iPFASs emitted from the WWTP were likely to undergo long-range atmospheric transport after entering the atmosphere via aqueous aerosols.

Exposure to Sodium p-Perfluorous Nonenoxybenzenesulfonate Induces Renal Fibrosis in Mice by Disrupting Lysine Metabolism

Environmental exposure is one driving factor of chronic kidney disease (CKD), yet the intrinsic molecular mechanisms are largely unexplored. As a persistent chemical, perfluorooctanesulfonate (PFOS) is regulated due to a great potential to induce multiple diseases, including renal fibrosis, a major pathological characteristic of CKD. It is hypothesized that sodium p-perfluorous nonenoxybenzenesulfonate (OBS), a typical alternative to PFOS, may also induce renal fibrosis. We observed distinct renal fibrosis in mice exposed to OBS. Metabolomics analysis showed that Nα-acetyllysine was the primary metabolite biomarker, whose level decreased greatly due to its excessive consumption by lysyloxidase (LOX). This suppressed the miR-140-5p expression, promoting upregulation of fibroblast growth factor 9 (FGF9), which activated the PI3K/Akt signaling pathway through fibroblast growth factor receptor 3 (FGFR3), thereby enhancing proliferation and activation of fibroblasts. Supplement of Nα-acetyllysine upregulated miR-140-5p expression, reduced expressions of FGF9 and FGFR3, and eventually ameliorated OBS-induced renal fibrosis. Similarly, treatment with miR-140-5p agomir and PI3K/Akt signaling pathway inhibitor LY294002 attenuated OBS-induced renal fibrosis. Taken together, OBS caused renal fibrosis through the LOX-Nα-acetyllysine-miR-140-5p-FGF9-FGFR3-PI3K/Akt-Bad-Bcl-2-fibroblast axis. The results of this study reveal a specific molecular axis for OBS to induce renal fibrosis and call for concerns in supervising the application of OBS.

Accurate detection and high throughput profiling of unknown PFAS transformation products for elucidating degradation pathways

The accurate detection of unknown per- and polyfluoroalkyl substances (PFAS) transformation products (TPs) is essential for elucidating degradation pathways and advancing remediation strategies. Herein, we developed a workflow that combined Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS) with a paired mass distance (PMD) network. This study achieved high throughput profiling of PFAS TPs with mDa resolving power and sub-ppm mass error. UV treatment revealed chain-shortening pathways, while plasma treatment uncovered competing mechanisms of chain shortening and lengthening, generating oxygen-rich TPs with increased hydrophilicity. Specifically, UV treatment of a 15-PFAS mixture and contaminated natural water showed disappearance of 7 unknown PFAS homologues and the emergence of 12 unknown PFAS homologues. Despite PFAS persistence under UV exposure, previously undetected low-abundance PFAS species were identified, indicating non-negligible photochemical transformation. Under plasma treatment of isolated PFOS, 39 unknown PFAS homologues including 142 suspect and 34 unknown PFAS TPs were identified, highlighting the extensive transformation of emerging and persistent PFAS. Overall, our approach enabled accurate and high-throughput profiling of unknown PFAS TPs and their degradation pathways, providing new insights into persistent unknown PFAS.

Emission of Perfluoroalkyl Acids and Perfluoroalkyl Ether Carboxylic Acids to the Atmosphere from a Fluorochemical Industrial Park in China

This study investigated the particle size distribution and atmospheric transport potential of perfluoroalkyl carboxylic acids (PFCAs) and certain perfluoroalkyl ether carboxylic acids (PFECAs) emitted from a mega fluoropolymer industrial park (FIP) in China. Ambient aerosols sampled in a residential area near the FIP were separated by a cascade impactor into five size fractions (<0.15 to 12.15 μm). Homologues of PFCAs (C5-C11) and five PFECAs were frequently detected in the samples (detection frequencies 40-100%), albeit not in all size fractions. Perfluorooctanoic acid (PFOA) exhibited the highest concentrations (6.5 to 2900 pg m-3). A noticeable mass mode in the >1 μm size range was observed for PFCAs and PFECAs in the samples that were directly influenced by wind from the direction of the FIP. Based on the PFOA concentrations in the aerosol samples, the emission rate of PFOA to air from the FIP was estimated to be 0.4-1.3 t year-1. Modeling results demonstrated that around 67% of the PFOA air emission was transported in the atmosphere above 1500 m in a 7 day continuous emission scenario, implying that the PFOA on <12.15 μm particles undergoes long-range atmospheric transport after being emitted from the FIP.

Unraveling the Exposure Spectrum of PFAS in Fluorochemical Occupational Workers: Structural Diversity, Temporal Trends, and Risk Prioritization

Despite extensive poly/perfluoroalkyl substance (PFAS) discovery studies in various samples, the exposure spectrum in fluorochemical occupational workers remains largely unexplored. Here, serum samples from 28 workers at a fluorochemical facility were analyzed using nontarget techniques, identifying 64 PFAS classes, including 15 novel ones such as pentafluorosulfur ether-substituted perfluoroalkyl sulfonic acids, hydrogen-substituted perfluoroalkylamines, and perfluoroalkylsulfonyl protocatechualdehyde esters. Temporal trend analyses (2008-2018) revealed stable levels for most PFAS but an increase in perfluorobutanoic acid (PFBA) and perfluorohexanesulfonic acid (PFHxS), suggesting industrial shifts from long-chain PFAS to short-chain homologues in China since the early 2010s. Commonly reported structurally modified PFAS (e.g., hydrogen/carbonyl/chlorine substitution, ether insertion, and unsaturation) were likely historical byproducts of legacy PFAS production rather than intentionally manufactured alternatives. A Toxicological Priority Index-based risk assessment, integrating mobility, persistence, and bioaccumulation indices, identified perfluoroalkylamines, di(perfluoroakyl sulfonyl)imides, structurally modified perfluoroalkyl sulfonic acids/carboxylic acids, and perfluoroalkylsulfonamidoacetic acids as high-risk PFAS chemicals. Overall, structurally modified PFAS exhibited higher mobility but lower persistence and bioaccumulation than legacy PFAS, except for chlorinated variants, which showed increased bioaccumulation potential. This study highlights critical gaps in the spectrum of historically emitted PFAS and emphasizes the need for large-scale monitoring and extensive risk assessments to manage emerging PFAS.

Unveiling airborne threats: Vertical profiles of multiple emerging pollutants in PM2.5 across the urban atmosphere of Southern China

PM2.5 has a detrimental impact on human health and has become a focus of widespread concern. The tempo-spatial distribution of emerging pollutants has been extensively studied, while there is a scarcity of understanding their vertical distribution in atmospheric environment. Here we investigated the vertical profiles of phthalate esters (PAEs), organophosphate esters (OPEs), neonicotinoids (NEOs), and per-and polyfluorinated substances (PFASs) in PM2.5 at ground level (4.5 m), 118 m, and 488 m in an urban environment. Results reveal that the PAEs in PM2.5 had higher concentrations than OPEs, NEOs, and PFASs. Vertical pollutant distribution generally exhibits a decline in concentration with increasing altitude. However, the opposite pattern also occurs, especially for NEOs and PFASs. The underlying mechanisms are multifaceted, encompassing the physicochemical characteristics of pollutants, meteorological parameters, and air-mass trajectories, each contributing to the vertical profile in varying degree. Additionally, the indoor health risks posed by outdoor pollutants at 118 m and 488 m were evaluated and found to be comparable to the outdoor risks at the ground. To our knowledge, this is the first exploration of the vertical characteristics of emerging pollutants at heights exceeding 100 meters, which provides a crucial reference for the prevention and control of emerging pollutants.

Assessing the efficacy of the Plasma Spinning Disc Reactor (PSDR) in treating undiluted Aqueous Film Forming Foams (AFFFs)

This work used pulsed electrical discharge plasma to treat undiluted Aqueous Film Forming Foam (AFFF) solution that contained significant quantities of per- and polyfluoroalkyl substances (PFAS). The plasma was generated within a plasma spinning disc reactor (PSDR), which utilizes the electric breakdown of argon gas to create plasma over a thin liquid film generated on a spinning disc. The PSDR performance toward degradation of AFFF constituents such as fluorotelomers, perfluorinated C2-C7 alkyl acids, and unidentified precursors was investigated. The PSDR performance sensitivity to the process parameters, such as reactor electrode design, disc rotational speed, liquid flowrate across the disc, and discharge voltage, was explored. The results indicate degradation of all quantified PFAS with chain length ≥ 4 to below detection limit within a 250 mL sample after 86 h of treatment on a 6.5 cm disc rotating at 200 rpm. The overall PSDR performance was insensitive to the tested process parameters. A direct comparison with a UV/H2O2 process revealed the superior performance of the plasma-based treatment toward degradation of perfluorinated compounds, evidenced by higher precursor removal rates and lower energy consumption. The energy efficiency of the UV/H2O2 system was approximately 100 times lower than that of the plasma process under all conditions. This study confirms that PSDR is a promising technology for effectively remediating PFAS in undiluted AFFF.

Chemical exposure in females of childbearing age associated with sex hormones: Evidence from an untargeted exposomic approach

Exposure to organic chemicals can cause reproductive hormones disturbance in women. However, there is very limited evidence regarding real-world chemical exposures in reproductive-aged women and their joint effects on sex hormone levels. Here, we applied non-targeted screening workflow based on High-Performance Liquid Chromatography-High-Resolution Mass Spectrometry to investigate the serum chemical exposome of 156 women of childbearing age from Jinan, China. A total of 185 exogenous chemicals from 19 categories were identified in at least 80% of serum samples with confidence levels 1-3, 84 of which have never been reported in humans, and 9 of those showed active effects on multiple biological targets in ToxCast program. A combination of grouped weighted quantile sum regression (GWQS), weighted quantile sum regression (WQS), quantile g calculation (q g-comp), and Bayesian kernel machine regression (BKMR) models indicated significant associations of chemical mixture exposure with progesterone (P4), testosterone (T), and luteinizing hormone (LH)/follicle-stimulating hormone (FSH) ratios, and 7, 4, and 8 priority contributors were identified, respectively, such as fipronil sulfone for P4, dicyclohexyl phthalate for T, and 3-hydroxybenzyl alcohol for LH/FSH. Three chemicals closely related to androgen synthesis and metabolism were proposed. Restricted cubic spline curves showed that 10 of the 28 priority compound-hormone pairs displayed significant non-monotonic exposure-response relationships. This study provides more information on the chemical exposome in Chinese women of childbearing age and has important implications for understanding the effect of chemical co-exposure on sex hormone homeostasis in women.

Exploring the Chemical Complexity and Sources of Airborne Fine Particulate Matter in East Asia by Nontarget Analysis and Multivariate Modeling

The complex and dynamic nature of airborne fine particulate matter (PM2.5) has hindered understanding of its chemical composition, sources, and toxic effects. In the first steps of a larger study, here, we aimed to elucidate relationships between source regions, ambient conditions, and the chemical composition in water extracts of PM2.5 samples (n = 85) collected over 16 months at an observatory in the Yellow Sea. In each extract, we quantified elements and major ions and profiled the complex mixtures of organic compounds by nontarget mass spectrometry. More than 50,000 nontarget features were detected, and by consensus of in silico tools, we assigned a molecular formula to 13,907 features. Oxygenated compounds were most prominent, followed by mixed nitrogenated/oxygenated compounds, organic sulfates, and sulfonates. Spectral matching enabled identification or structural annotation of 43 substances, and a workflow involving SIRIUS and MS-DIAL software enabled annotation of 74 unknown per- and polyfluoroalkyl substances with primary source regions in China and the Korean Peninsula. Multivariate modeling revealed seasonal variations in chemistry, attributable to the combination of warmer temperatures and maritime source regions in summer and to cooler temperatures and source regions of China in winter.

A systematic review for non-targeted analysis of per- and polyfluoroalkyl substances (PFAS)

This review follows the PRISMA guidelines to provide a systematic review of 115 peer reviewed articles that used non-targeted analysis (NTA) methods to detect per- and polyfluoroalkylated substances (PFAS). This literature highlights the significant positive impact of NTA in understanding PFAS in the environment. Within the literature a geographical bias exists, with most NTA studies (∼60 %) conducted in the United States and China. Future studies in other regions (such as South America and Africa) are needed to gain a more global understanding. More research is required in marine environments and the atmosphere, as current studies focus mainly on freshwater, groundwater, soil, and sediments. The majority of studies focus on measuring PFAS in the environment, rather than in commercial products (with the exception of AFFF). Non-lethal blood sampling has been successful for NTA in humans and wildlife, but additional biomonitoring studies are required on exposed cohorts to understand health risks and PFAS biotransformation pathways. NTA methods mostly use liquid chromatography and negative ionisation, which biases the literature towards the detection of specific PFAS. Despite improvements in data reporting and quality assurance and control (QA/QC) procedures, factors such as false negative and false positive rates are often overlooked, and many NTA workflows remain highly subjective. Perfluoroalkyl carboxylic acids (PFCAs) and perfluoroalkyl sulfonic acids (PFSAs) are the most detected PFAS classes, identified in over 80 % of NTA studies, and are common in routine monitoring. However, our review identified >1000 PFAS from a total of 382 different PFAS classes, with over 300 classes found in fewer than 5 % of studies. This highlights the variety of different PFAS present in the environment, and the limitations of relying solely on targeted methods. Future monitoring programs and regulations would benefit from considering NTA methods to provide more comprehensive information on PFAS present in the environment.

Enzymatic Degradation of PFAS: Current Status and Ongoing Challenges

Per- and polyfluoroalkyl substances (PFAS) are often considered the quintessential example of industrial chemical pollution - they are toxic and ubiquitous environmental contaminants that are extremely difficult to degrade. There has been a large research focus on the development of effective and renewable degradation technologies. In comparison to traditional pollutant degradation techniques, such as advanced oxidation processes and electrochemistry, degradation of PFAS using extracellular enzymes offers an eco-friendly solution as enzymes are biodegradable, recyclable and have low energy and chemical requirements. This review outlines the current understanding of extracellular enzymatic degradation of PFAS with a focus on reported results and proposed degradation mechanisms. More importantly, this review highlights limitations that hinder the application of enzymes for PFAS degradation and proposes critical future research that is needed to improve the applicability of this promising remediation strategy.

Spatial and seasonal distribution, sources, and health risks of PM2.5 loaded per- and polyfluoroalkyl substances (PFASs) in a typical megacity

Per- and polyfluoroalkyl substances (PFASs), a class of ubiquitous and emerging environmental pollutants, have garnered considerable attention due to the scarcity of knowledge regarding their atmospheric sources and the associated human health risks from aerosol exposure. This study investigated the spatial-temporal distribution and potential sources of PFASs in Nanjing city of eastern China by collecting 66 PM2.5 samples from industrial, urban, and rural areas between July 2022 and August 2023. Employing ultra-performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS), 21 distinct PFASs were detected with concentrations ranging from 9.62 to 136 pg·m-3, predominantly higher in urban areas. Airborne PFASs concentrations exhibited seasonal fluctuations, with the highest levels observed in autumn, followed by spring, summer and winter. Diagnostic ratio and positive matrix factorization (PMF) for source analyses revealed the significant influence of long-range transport, the textile and paper packaging industry, and the decomposition of fluorochemical precursors were identified as the main contributors, accounting for 18.2 %, 15.8 %, and 16.1 % respectively. Population exposure was evaluated through deposition and dermal penetration modeling, with inhalation intake estimated at 2.05 pg·kg-1·d-1 and dermal contact intake at 1.01 pg·kg-1·d-1. Among the 21 assessed PFASs, perfluoro-n-hexanoic acid (PFHxA) was identified posing the most significant risk regarding respiratory effects, skin sensitization, and carcinogenic potential. This research provides critical insights into the spatial and seasonal distribution of atmospheric PFASs and the assessment of combined human exposure risks in rapidly developing areas.

Latest trends in the environmental analysis of PFAS including nontarget analysis and EOF-, AOF-, and TOP-based methodologies

Ubiquitous environmental occurrence of per- and polyfluoroalkyl substances (PFAS) underscores the critical need to broaden investigative efforts in effective screening, risk assessment, and remediation. Owing to the broad spectrum of PFAS, various analytical techniques have been extensively utilized to attain inclusivity, with notable attention given to methods such as extractable organic fluorine (EOF), adsorbable organic fluorine (AOF), and the total oxidizable precursor (TOP) assay. These techniques expand the scope of PFAS analysis by estimating perfluoroalkyl acid precursors or the total organochlorine fraction. This review offers a comprehensive comparative overview of up-to-date methodologies, alongside acknowledging the inherent limitations associated with their applications. When coupled with target analysis via low-resolution tandem mass spectrometry, these techniques offer a potential estimation of total PFAS concentrations. Yet, analytical challenges such as the limited availability of reference analytical standards, partial PFAS adsorption, and the entrapment of fluorinated inorganic anions on adsorbent materials often restrict the comprehensiveness of PFAS analysis. So, integrating nontarget analysis using high-resolution mass spectrometry (HRMS) tools fortifies these PFAS mass balance approaches, enabling the development of a more holistic approach for an environmental analysis framework. This review provides additional insights into the comparative advantages of PFAS analytical approaches and explores various data prioritization strategies in nontarget screening methods. It advocates for the necessary optimization of PFAS extraction methods, asserting that integrating the nontarget approach would foster the establishment of a comprehensive monitoring framework across diverse environmental matrices. Such integration holds promise for enhancing scientific comprehension of PFAS contamination across diverse environmental matrices.

Exposure to per- and polyfluoroalkyl substances (PFAS) in North Carolina homes: results from the indoor PFAS assessment (IPA) campaign

Per and polyfluoroalkyl substances (PFAS) are ubiquitous in the indoor environment, resulting in indoor exposure. However, a dearth of concurrent indoor multi-compartment PFAS measurements, including air, has limited our understanding of the contributions of each exposure pathway to residential PFAS exposure. As part of the Indoor PFAS Assessment (IPA) Campaign, we measured 35 neutral and ionic PFAS in air, settled dust, drinking water, clothing, and on surfaces in 11 North Carolina homes. Ionic and neutral PFAS measurements reported previously and ionic PFAS measurements reported herein for drinking water (1.4-34.1 ng L-1), dust (202-1036 ng g-1), and surfaces (4.1 × 10-4-1.7 × 10-2 ng cm-2) were used to conduct a residential indoor PFAS exposure assessment. We considered inhalation of air, ingestion of drinking water and dust, mouthing of clothing (children only), and transdermal uptake from contact with dust, air, and surfaces. Average intake rates were estimated to be 3.6 ng kg-1 per day (adults) and 12.4 ng kg-1 per day (2 year-old), with neutral PFAS contributing over 80% total PFAS intake. Excluding dietary ingestion, which was not measured, inhalation contributed over 65% of PFAS intake and was dominated by neutral PFAS because fluorotelomer alcohol (FTOH) concentrations in air were several orders of magnitude greater than ionic PFAS concentrations. Perfluorooctanoic acid (PFOA) intake was 6.1 × 10-2 ng kg-1 per day (adults) and 1.5 × 10-1 ng kg-1 per day (2 year-old), and biotransformation of 8 : 2 FTOH to PFOA increased this PFOA body burden by 14% (adults) and 17% (2 year-old), suggesting inhalation may also be a meaningful contributor to ionic PFAS exposure through biotransformation.

Interrogation of a fluoropolymer dispersion manufactured with a non-fluorinated polymerization aid for targeted and non-targeted fluorinated residuals by liquid chromatography high resolution mass spectrometry

Recent advances in fluoropolymer polymerization have focused on replacing perfluorinated polymerization aids (PAs) with hydrocarbon-based alternatives. Hydrocarbon PAs are vulnerable to fluorinated radicals during polymerization, leading to the creation of hundreds of process-specific polyfluorinated residuals. These residuals, which include low molecular weight extractable or leachable impurities, are challenging to detect at trace levels. This study investigates a polytetrafluoroethylene (PTFE) dispersion prepared with a hydrocarbon-based surfactant (DOSS) to measure these process-specific fluorinated residues. Liquid chromatography high resolution mass spectrometry is one of the few analytical methods that offers the sensitivity and selectivity required to detect these residuals in complex matrices at concentrations as low as parts per billion. The results indicate that using a hydrocarbon PA during emulsion polymerization produces numerous polyfluorinated residuals. These must be identified and monitored to develop effective abatement strategies, ensuring responsible fluoropolymer manufacturing.

Interaction and coexistence characteristics of dissolved organic matter and toxic metals with per- and polyfluoroalkyl substances in landfill leachate

Landfill leachate-containing per- and polyfluoroalkyl substances (PFAS) is both an important 'sink' and a 'source' of secondary pollution, posing serious threaten to surrounding environments. To date, the pollution characteristics of PFAS in landfill leachate, and the coexistence and interaction between PFAS and other leachate contaminants, such as dissolved organic matter (DOM) and toxic metals remains unclear. Herein, our results showed that 17 target PFAS, with concentrations ranged from 1804 to 43309 ng/L, were detected in landfill leachates. The main PFAS were short-chain and even-chain substances represented by perfluorobutanoic acid (PFBA) and perfluorobutane sulfonic acid (PFBS). Leachate derived DOM is mainly composed of protein-like and humic-like substance, among which the total contribution of protein-like substance is as high as 73.7%. Correlation analysis results showed that the distribution of PFAS was strongly correlated with the substituted functional groups (e.g., carboxyl and hydroxyl) on the aromatic ring of humic-like substance (C2 and E253/E203) and autochthonous metabolism by microbial activities (FI). Furthermore, Mn element showed a significantly strong correlation with PFAS. Both organic and inorganic substances positively correlated with toxic metals. Our findings are helpful to understand the environmental fate of PFAS, and contribute to decision-making regarding DOM, toxic metals, and PFAS management in landfill.

Characterization of AhR-mediated potency in sediments from Kongsfjorden, Svalbard: Application of effect-directed analysis and nontarget screening

In this study, we aimed to identify the major aryl hydrocarbon receptor (AhR) agonists in surface sediments (S1-S10, n = 10) from Kongsfjorden, Arctic Svalbard, using effect-directed analysis. High AhR-mediated potencies were observed in the mid-polar fractions and RP-HPLC subfractions (F2.6-F2.8; log KOW 5-8) in the sediments of sites S2 and S3, which are located near abandoned coal mine areas, as assessed by the H4IIE-luc bioassay. The concentrations of traditional polycyclic aromatic hydrocarbon (t-PAHs), emerging PAHs, alkyl-PAHs, and styrene oligomers ranged from 6.1 to 2100 ng g-1 dry weight (dw), 0.5-1000 ng g-1 dw, 47 to 79,000 ng g-1 dw, and 4.2-130 ng g-1 dw, respectively, with elevated levels in S2 and S3. Principal component analysis coupled with multiple linear regression suggested that t-PAHs in sediments primarily originated from coal, petroleum combustion, and coal combustion. Twenty-four target AhR agonists accounted for 3.2%-100% (mean = 47%) of the total AhR-mediated potencies in S2 and S3. Nontarget screening via GC-QTOFMS in the highly potent fractions identified 48 AhR agonist candidates through four-step selection criteria. Among these, 27 compounds were identified as coal-derived substances. VirtualToxLab in silico modeling predicted that most of the 48 tentative AhR agonist candidates could bind to AhR. Overall, our findings indicate significant contamination of the Kongsfjorden sediments by coal-derived substances, highlighting the need for further studies to assess the ecological risks associated with these contaminants.

Identification of emerging PFAS in industrial sludge from North China: Release risk assessment by the TOP assay

Per- and polyfluoroalkyl substances (PFAS) have been widely used across various industries, leading to their prevalent occurrence in sludges generated by wastewater treatment plants (WWTPs). Consequently, industrial sludges serve as typical reservoirs for PFAS. This study examined 46 target PFAS in sludge samples intended for brick production from nine WWTPs in North China, identifying emerging PFAS and categorizing their behaviors through high-resolution mass spectrometry (HRMS) screening and total oxidizable precursor (TOP) assay. Forty-one PFAS were detected, with trifluoroacetic acid (TFA), perfluorooctane sulfonic acid, and hexafluoropropylene oxide dimer acid being the most prevalent. Twenty-nine emerging PFAS were identified, and their behaviors were categorized using TOP assay. Notably, four CF3-containing PFAS were identified, all confirmed as precursors of TFA, with a molar yield of 16.4 %-25.6 % in Milli-Q water during TOP assay validation. These findings indicate that the transformation of these precursors during sludge recycling may substantially contribute to TFA release, underscoring potential risks associated with secondary PFAS release during sludge resource utilization.

Indoor air concentrations of PM2.5 quartz fiber filter-collected ionic PFAS and emissions to outdoor air: findings from the IPA campaign

Per- and polyfluoroalkyl substances (PFAS) are prevalent in consumer products used indoors. However, few measurements of ionic PFAS exist for indoor air. We analyzed samples collected on PM2.5 quartz fiber filters (QFFs) in 11 North Carolina homes 1-3 times in living rooms (two QFFs in series), and immediately outside each home (single QFF), for 26 ionic PFAS as part of the 9 months Indoor PFAS Assessment (IPA) Campaign. All targeted PFAS, except for PFDS and 8:2 monoPAP, were detected indoors. PFBA, PFHpA, PFHxA, PFOA, PFOS, and 6:2 diPAP were detected in >50% of indoor samples. PFHxA, PFOA, and PFOS had the highest detection frequency (DF = 80%; medians = 0.5-0.7 pg m-3), while median PFBA concentrations (3.6 pg m-3; DF = 67%) were highest indoors. Residential indoor air concentrations (sum of measured PFAS) were, on average, 3.4 times higher than residential outdoor air concentrations, and an order of magnitude higher than regional background concentrations. Indoor-to-outdoor emission rate estimates suggest that emissions from single unit homes could be a meaningful contributor to PFBA, PFOA, and PFOS emissions in populated areas far from major point sources. Backup QFFs were observed to adsorb some targeted PFAS from the gas-phase, making reported values upper-bounds for particle-phase and lower-bounds for total air (gas plus particle) concentrations. We found that higher concentrations of carbonaceous aerosol were associated with a shift in partitioning of short chain PFCAs and long chain PFSAs toward the particle phase.

Identification of Emerging Per- and Polyfluoroalkyl Substances (PFAS) in E-waste Recycling Practices and New Precursors for Trifluoroacetic Acid

Electronic waste is an emerging source of per- and polyfluoroalkyl substance (PFAS) emissions to the environment, yet the contribution from hazardous recycling practices in the South Asian region remains unclear. This study detected 41 PFAS in soil samples from e-waste recycling sites in Pakistan and the total concentrations were 7.43-367 ng/g dry weight (dw) (median: 37.7 ng/g dw). Trifluoroacetic acid (TFA) and 6:2 fluorotelomer sulfonic acid emerged as the dominant PFAS, constituting 49% and 13% of the total PFAS concentrations, respectively. Notably, nine CF3-containing emerging PFAS were identified by the high-resolution mass spectrometry (HRMS)-based screening. Specifically, hexafluoroisopropanol and bistriflimide (NTf2) were consistently identified across all the samples, with quantified concentrations reaching up to 854 and 90 ng/g dw, respectively. This suggests their potential association with electronic manufacturing and recycling processes. Furthermore, except for NTf2, all the identified emerging PFAS were confirmed as precursors of TFA with molar yields of 8.87-40.0% by the TOP assay validation in Milli-Q water. Overall, this study reveals significant emission of PFAS from hazardous e-waste recycling practices and emphasizes the identification of emerging sources of TFA from precursor transformation, which are essential for PFAS risk assessment.

Recognition of screening out hierarchical toxic contaminants tuned by quantified pseudo-components from complex engineering co-combustion

Co-combustion of industrial and municipal solid wastes has emerged as the most promising disposal technology, yet its effect on unknown contaminants generation remains rarely revealed due to waste complexity. Hence, six batches of large-scale engineering experiments were designed in an incinerator of 650 t/d, which overcame the inauthenticity and deviation of laboratory tests. 953-1772 non-targeted compounds were screened in fly ash. Targeting the impact of co-combustion, a pseudo-component matrix model was innovatively integrated to quantitatively extract nine components from complex wastes grouped into biomass and plastic. Thus, the influence was evaluated across eight dimensions, covering molecular characteristics and toxicity. The effect of co-combustion with biomass pseudo-components was insignificant. However, co-combustion with high ratios of plastic pseudo-components induced higher potential risks, significantly promoting the formation of unsaturated hydrocarbons, highly unsaturated compounds (DBE≥15), and cyclic compounds by 19 %- 49 %, 17 %- 31 %, and 7 %- 27 %, respectively. Especially, blending with high ratios of PET plastic pseudo-components produced more species of contaminants. Unique 2 Level I toxicants, bromomethyl benzene and benzofuran-2-carbaldehyde, as well as 4 Level II toxicants, were locked, receiving no concern in previous combustion. The results highlighted risks during high proportion plastics co-combustion, which can help pollution reduction by tuning source wastes to enable healthy co-combustion.

Impacts of PFOS, PFOA and their alternatives on the gut, intestinal barriers and gut-organ axis

With the restricted use of perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA), a number of alternatives to PFOS and PFOA have attracted great interest. Most of the alternatives are still characterized by persistence, bioaccumulation, and a variety of toxicity. Due to the production and use of these substances, they can be detected in the atmosphere, soil and water body. They affect human health through several exposure pathways and especially enter the gut by drinking water and eating food, which results in gut toxicity. In this review, we summarized the effects of PFOS, PFOA and 9 alternatives on pathological changes in the gut, the disruption of physical, chemical, biological and immune barriers of the intestine, and the gut-organ axis. This review provides a valuable understanding of the gut toxicity of PFOS, PFOA and their alternatives as well as the human health risks of emerging contaminants.

Nontarget Analysis of Legacy and Emerging PFAS in a Lithium-Ion Power Battery Recycling Park and Their Possible Toxicity Measured Using High-Throughput Phenotype Screening

Driven by the global popularity of electric vehicles and the shortage of critical raw materials for batteries, the spent lithium-ion power battery (LIPB) recycling industry has exhibited explosive growth in both quantity and scale. However, relatively little information is known about the environmental risks posed by LIPB recycling, in particular with regards to perfluoroalkyl and polyfluoroalkyl substances (PFAS). In this work, suspect screening and nontarget analysis were carried out to characterize PFAS in soil, dust, water and sediment from a LIPB recycling area. Twenty-five PFAS from nine classes were identified at confidence level 3 or above, including 13 legacy and 12 emerging PFAS, as well as two ultrashort-chain PFAS. Based on the target analysis of 16 PFAS, at least nine were detected in each environmental sample, indicating their widespread presence in a LIPB recycling area. Perfluorodecanoic acid, perfluorooctanesulfonic acid and trifluoromethanesulfonamide showed significant differences in the four phenotypic parameters (growth, movement, survival and fecundity) of Caenorhabditis elegans and were the most toxic substances in all target PFAS at an exposure concentration of 200 μM. Our project provides first-hand information on the existence and environmental risk of PFAS, facilitating the formulation of regulations and green development of the LIPB recycling industry.

Emission of volatile organic compounds during open fire cooking with wood biomass: Traditional three-stone open fire vs. gasifier cooking stove in rural Kenya

Cooking with wood biomass fuels releases hazardous air pollutants, including volatile organic compounds (VOCs), that often disproportionally affect women and children. This study, conducted in Kwale and Siaya counties in Kenya, employed thermal desorption gas chromatography - mass spectrometry to analyse VOC emissions from cooking with a wood biomass three-stone open fire vs. top-lit updraft gasifier stove. In kitchens with adequate ventilation, total VOC levels increased from 35-252 μg∙m-3 before cooking to 2235-5371 μg∙m-3 during open fire cooking, whereas use of a gasifier stove resulted in reduced emissions from cooking by 48-77 % (506-2778 μg∙m-3). However, in kitchens with poor ventilation, there was only a moderate difference in total VOC levels between the two methods of cooking (9034-9378 μg∙m-3 vs. 6727-8201 μg∙m-3 for the three-stone open fire vs. gasifier stove, respectively). Using a non-target screening approach revealed significantly increased levels of VOCs, particularly benzenoids, oxygenated and heterocyclic compounds, when cooking with the traditional open fire, especially in closed kitchens, highlighting the effects of poor ventilation. Key hazardous VOCs included benzene, naphthalene, phenols and furans, suggesting potential health risks from cooking. In kitchens with good ventilation, use of the gasifier stove markedly reduced emissions of these priority toxic VOCs compared to cooking with an open fire. Thus, substituting open fires with gasifier stoves could help to improve household air quality and alleviate health risks. The study revealed that VOCs were present prior to cooking, possibly originating from previously cooked food (buildup) or the outside environment. VOC emissions were also exacerbated by reduced air flow in high humidity during rainfall, suggesting an area for further research. The findings underscore the importance of adopting cleaner cooking technologies and enhancing kitchen ventilation to mitigate the impacts of VOCs in developing countries.

Understanding the role of atmospheric deposition on the environmental load of per- and polyfluoroalkyl substances: A case study in Three Gorges Reservoir, China

Sixty-nine total suspended particle (TSP) samples, paired with forty-eight surface soil samples, covering four seasons from January 2021 to November 2021, were collected from the Three Gorges Reservoir Region (TGRR). Twenty per- and poly-fluoroalkyl substances (PFASs) were analyzed to evaluate their contamination characteristics and understand the role of atmospheric deposition on the environmental loads in TGRR. The annual average concentrations of PFASs in TSP and soil were 37.2 ± 1.22 pg·m-3 and 0.798 ± 0.134 ng·g-1, respectively. For TSP, concentrations were highest in spring and lowest in summer. For soil, it was in autumn and winter, respectively. The seasonality was more influenced by anthropogenic activities than by meteorological conditions or physicochemical parameters of the soil. Positive matrix fractionation (PMF) indicated that, based on annual averages, PFOA-based products (40.2 %) were the major sources of PFASs in TSP, followed by PFOS-based products (25.2 %) and precursor degradation (34.6 %). The highest source contributor for PFASs in spring was precursor degradation (40.9 %), while in other three seasons, it was PFOA-based products (39.9 %, 40.9 % and 52.0 %, respectively). The mean atmospheric dry and wet deposition fluxes of PFASs were estimated at 4.38 ng·m-2·day-1 and 23.5 ng·m-2·day-1, respectively. The contribution of atmospheric deposition to the inventory mass of PFASs in the surface soil was 22.3 %. These findings fill a gap in knowledge regarding the processes and mechanisms of the occurrence, sources and atmospheric deposition of PFASs in the TGRR.

Bio-accumulation and health risk assessments of per- and polyfluoroalkyl substances in wheat grains

Per- and polyfluoroalkyl substances (PFASs) have been widely detected in various food, which has attracted worldwide concern. However, the factors influencing the transfer and bio-accumulation of PFASs from soils to wheat in normal farmland, is still ambiguous. We investigated the PFASs accumulation in agricultural soils and grains from 10 cites, China, and evaluated the health risks of PFASs via wheat consumption. Our results show that ∑PFASs in soils range from 0.34 μg/kg to 1.59 μg/kg with PFOA and PFOS dominating, whilst ∑PFASs in wheats range from 2.74 to 6.01 μg/kg with PFOA, PFBA and PFHxS dominating. The lower pH conditions and high total organic carbon (TOC) could result in the higher accumulation of PFASs in soils and subsequently in wheat grains, whilst the bioaccumulation factors of PFASs increase with increasing pH conditions but not with TOC. The estimated daily intake (EDI) values of PFBA, PFOA, and PFHxS are relatively high, but data supports that ingesting wheat grains does not result in any potential risk to the human beings. Our studies provided more information about PFASs accumulation in wheat grains, and help us understand the current potential risks of PFASs in food.

Machine learning-enhanced molecular network reveals global exposure to hundreds of unknown PFAS

Unknown forever chemicals like per- and polyfluoroalkyl substances (PFASs) are difficult to identify. Current platforms designed for metabolites and natural products cannot capture the diverse structural characteristics of PFAS. Here, we report an automatic PFAS identification platform (APP-ID) that screens for PFAS in environmental samples using an enhanced molecular network and identifies unknown PFAS structures using machine learning. Our networking algorithm, which enhances characteristic fragment matches, has lower false-positive rate (0.7%) than current algorithms (2.4 to 46%). Our support vector machine model identified unknown PFAS in test set with 58.3% accuracy, surpassing current software. Further, APP-ID detected 733 PFASs in real fluorochemical wastewater, 39 of which are previously unreported in environmental media. Retrospective screening of 126 PFASs against public data repository from 20 countries show PFAS substitutes are prevalent worldwide.

Innovation of BiOBr/BiOI@Bi5O7I Ternary Heterojunction for Catalytic Degradation of Sodium P-Perfluorous Nonenoxybenzenesulfonate

As an alternative for perfluorooctane sulfonic acid (PFOS), sodium p-perfluorononyloxybenzene sulfonate (OBS) has been widely used in petroleum, fire-fighting materials, and other industries. In order to efficiently and economically remove OBS contaminations from water bodies, in this study, a ternary heterojunction was constructed by coupling BiOBr and BiOI@Bi5O7I for improving the redox capacity and carrier separation ability of the material and investigating the effect of the doping ratios of BiOBr and BiOI@ Bi5O7I on the performance of the catalysts. Furthermore, the effects on the degradation of OBS were also explored by adjusting different catalyst doping ratios, OBS concentrations, catalyst amounts, and pH values. It was observed that when the concentration of OBS was 50 mg/L, the amount of catalyst used was 0.5 g/L, and the pH was not changed. The application of BiOBr/BiOI@ Bi5O7I consisting of 25% BiOBr and 75% BiOI@ Bi5O7I showed excellent stability and adsorption degradation performance for OBS, and almost all of the OBS in the aqueous solution could be removed. The removal rate of OBS by BiOBr/BiOI@ Bi5O7I was more than 20% higher than that of OBS by BiOI@Bi5O7I and BiOBr when the OBS concentration was 100 mg/L. In addition, the reaction rate constants of BiOBr/BiOI@ Bi5O7I were 2.4 and 10.8 times higher than those of BiOI@ Bi5O7I and BiOBr, respectively. Therefore, the BiOBr/BiOI@ Bi5O7I ternary heterojunction can be a novel type of heterojunction for the efficient degradation of OBS in water bodies.

Suspect, Nontarget Screening, and Toxicity Prediction of Per- and Polyfluoroalkyl Substances in the Landfill Leachate

Landfills are the final stage of urban wastes containing perfluoroalkyl and polyfluoroalkyl substances (PFASs). PFASs in the landfill leachate may contaminate the surrounding groundwater. As major environmental pollutants, emerging PFASs have raised global concern. Besides the widely reported legacy PFASs, the distribution and potential toxic effects of numerous emerging PFASs remain unclear, and unknown PFASs still need discovery and characterization. This study proposed a comprehensive method for PFAS screening in leachate samples using suspect and nontarget analysis. A total of 48 PFASs from 10 classes were identified; nine novel PFASs including eight chloroperfluoropolyether carboxylates (Cl-PFPECAs) and bistriflimide (HNTf2) were reported for the first time in the leachate, where Cl-PFPECA-3,1 and Cl-PFPECA-2,2 were first reported in environmental media. Optimized molecular docking models were established for prioritizing the PFASs with potential activity against peroxisome proliferator-activated receptor α and estrogen receptor α. Our results indicated that several emerging PFASs of N-methyl perfluoroalkyl sulfonamido acetic acids (N-MeFASAAs), n:3 fluorotelomer carboxylic acid (n:3 FTCA), and n:2 fluorotelomer sulfonate (n:2 FTSA) have potential health risks that cannot be ignored.

Per- and polyfluoroalkyl substance (PFAS) mixtures induce gut microbiota dysbiosis and metabolic disruption in silkworm (Bombyx mori L.)

Mixed legacy and emerging per- and polyfluoroalkyl substances (PFASs) are commonly found in soil and dust; however, the potential toxicity of PFAS mixtures (mPFASs) in insects is unknown. Using 16S rRNA gene sequencing and transcriptome sequencing (RNA-Seq), we evaluated the adverse effects of mPFASs on silkworms, a typical lepidopteran insect. After exposure to mPFASs, the silkworm midgut was enriched with high levels of PFASs, which induced histopathological changes. The composition of the midgut microbiota was significantly affected by mPFAS exposure, and functional predictions revealed significant disruption of some metabolic pathways. RNA-seq analysis revealed that mPFASs significantly changed the transcription profiles. Functional enrichment analysis of the differentially expressed genes also revealed that biological processes related to metabolic pathways and the digestive system were significantly affected, similar to the results of the gut microbiota analysis, suggesting that mPFAS exposure had an adverse effect on the metabolic function of silkworms and may further affect their normal growth. Finally, the significant correlation between abundance changes in the gut microbiota and metabolism/digestion-related genes further highlighted the role of the gut microbiota in mPFAS-related processes affecting the metabolic functions of silkworms. To our knowledge, this study is the first to evaluate the toxic effects of mPFASs in insects and provide basic data for further PFAS toxicity investigations in insects and comprehensive ecological risk assessments of mPFASs.

Comparison of high-resolution mass spectrometry acquisition methods for the simultaneous quantification and identification of per- and polyfluoroalkyl substances (PFAS)

Simultaneous identification and quantification of per- and polyfluoroalkyl substances (PFAS) were evaluated for three quadrupole time-of-flight mass spectrometry (QTOF) acquisition methods. The acquisition methods investigated were MS-Only, all ion fragmentation (All-Ions), and automated tandem mass spectrometry (Auto-MS/MS). Target analytes were the 25 PFAS of US EPA Method 533 and the acquisition methods were evaluated by analyte response, limit of quantification (LOQ), accuracy, precision, and target-suspect screening identification limit (IL). PFAS LOQs were consistent across acquisition methods, with individual PFAS LOQs within an order of magnitude. The mean and range for MS-Only, All-Ions, and Auto-MS/MS are 1.3 (0.34-5.1), 2.1 (0.49-5.1), and 1.5 (0.20-5.1) pg on column. For fast data processing and tentative identification with lower confidence, MS-Only is recommended; however, this can lead to false-positives. Where high-confidence identification, structural characterisation, and quantification are desired, Auto-MS/MS is recommended; however, cycle time should be considered where many compounds are anticipated to be present. For comprehensive screening workflows and sample archiving, All-Ions is recommended, facilitating both quantification and retrospective analysis. This study validated HRMS acquisition approaches for quantification (based upon precursor data) and exploration of identification workflows for a range of PFAS compounds.

Suspect and nontarget screening of per- and polyfluoroalkyl substances based on ion mobility mass spectrometry and machine learning techniques

High-resolution mass spectrometry (HRMS)-based suspect and nontarget screening techniques are powerful tools for the comprehensive identification of per- and polyfluoroalkyl substances (PFASs), but the interference of complex matrices (especially for wastewater) pose an analytical challenge. This study explored the potential of combining ion mobility spectrometry (IMS) with HRMS and machine learning techniques to achieve the rapid and accurate suspect and nontarget screening of PFAS in wastewater. There were fewer interfering peaks and a clearer spectrum in the data acquired by IMS-HRMS than conventional HRMS. The introduction of collision cross section (CCS) in PFAS homologous series search could filter out 63% of false positive results. Retention time and CCS prediction models were helpful in improving the confidence for PFAS qualitative identification and the random forest algorithm combined with RDKit descriptor performed best for CCS prediction. With the inclusion of extra dimensional information, this study also proposed a comprehensive and concise confidence assignment criterion to better convey the certainty of the qualitative identification of PFAS. Finally, a total of 56 potential PFASs were identified in the wastewater sample using the newly developed method and 45 of them were identified outside reference standards, emphasizing the importance of suspect and nontarget screening for PFAS.

Adipogenic and osteogenic effects of OBS and synergistic action with PFOS via PPARγ-RXRα heterodimers

Sodium p-perfluorous nonenoxybenzenesulfonate (OBS) is a novel alternative to perfluorooctane sulfonate (PFOS), with environmental health risks largely unknown. The present study aims to unravel the adipogenesis effects and underlying molecular initiating events of OBS, which are crucial for understanding and predicting its adverse outcome. In undifferentiated human mesenchymal stem cells (hMSCs), exposure to 1-100 nM of OBS for 7 days stimulated reactive oxygen species production. In the subsequent multipotent differentiation, hMSCs favored adipogenesis and repressed osteogenesis. The point of departure (PoD) for cellular responses of OBS was 38.85 nM, higher than PFOS (0.39 nM). Notably, OBS/PFOS co-exposure inhibited osteogenesis and synergistically promoted adipogenesis. Consistently, the expression of adipogenic marker genes was up-regulated, while that of osteogenic marker genes was down-regulated. The decreased adiponectin and elevated tumor necrosis factor α (TNFα) secretion were observed in differentiated cells exposed to the mixture of OBS and PFOS. The co-treatment of a peroxisome proliferator-activated receptor γ (PPARγ) antagonist alleviated the adipogenic effects of PFOS and its combination with OBS. Moreover, OBS/PFOS co-exposure induced peroxisome PPARγ activation in reporter gene assays, and increased formation of PPARγ - retinoid X receptor α (RXRα) heterodimers measured by co-immunoprecipitation assays. Molecular docking showed interaction energy of OBS (-20.7 kcal/mol) with intact PPARγ-RXRα complex was lower than that of PFOS (-25.9 kcal/mol). Overall, single OBS exhibited lower potency in inducing adipogenesis but is comparable to PFOS in repressing osteogenesis, whereas OBS/PFOS co-exposure increases interaction with PPARγ-RXRα heterodimers, resulting in the synergistic activation of PPARγ, ultimately enhancing adipogenesis at the expense of osteogenic differentiation. The results indicate the potential health risks of increased obesity and decreased bone density caused by OBS and its co-exposure with PFOS, as well as other perfluorinated alkylated substances mixtures.

Nitroaromatic Compounds from Secondary Nitrate Formation and Biomass Burning Are Major Proinflammatory Components in Organic Aerosols in Guangzhou: A Bioassay Combining High-Resolution Mass Spectrometry Analysis

The limited characterization and detection capacity of unknown compounds hinder our understanding of the molecular composition of toxic compounds in PM2.5. The present study applied Fourier transform ion cyclotron resonance mass spectrometry coupled with negative and positive electrospray ionization sources (ESI-/ESI+ FT-ICR-MS) to probe the molecular characteristics and dynamic formation processes of the effective proinflammatory components in organic aerosols (OAs) of PM2.5 in Guangzhou for one year. We detected abundant proinflammatory molecules in OAs, mainly classified as CHON compounds (compounds composed of C, H, O, and N atoms) in elemental and nitroaromatic compounds (NACs) in structures. From the perspective of the formation process, we discovered that these proinflammatory molecules, especially toxic NACs, were largely driven by secondary nitrate formation and biomass burning (in emission source), as well as SO2 (in atmospheric evolution). In addition, our results indicated that the secondary processes had replaced the primary emission as the main contributing source of the toxic proinflammatory compounds in OAs. This study highlights the importance of community measures to control the production of nitroaromatic compounds derived from secondary nitrate formation and biomass burning in urban areas.

Optimization for the analysis of 42 per- and polyfluorinated substances in human plasma: A high-throughput method for epidemiological studies

There is an increasing awareness about the presence of per- and polyfluoroalkyl substances (PFAS) in many environmental and biological compartments, including human biofluids and tissues. However, the increase of PFAS replacements, including alternatives with shorter chain or less bioaccumulative potential, has broaden the exposure and the need for wider identification procedures. Moreover, the low volumes available for human blood or plasma, and the high number of samples needed to assess adequately epidemiologic studies, require particularly fast, reproducible and, if possible, miniaturized protocols. Therefore, accurate and robust analytical methods are still needed to quantify the PFAS's burden in humans and to understand potential health risks. In this study, we have developed and validated the analysis of 42 PFAS in human plasma by means of a Captiva 96-well micro extraction plate and a LC-q-Orbitrap. For the optimization of the analytical workflow, three extraction/clean-up methods were tested, and the selected one was validated using spiked artificial and bovine plasma at four concentration levels. The final method showed high absolute recoveries for the 42 PFAS, ranging from 52% to 130%, instrumental detection limits between 0.001-0.6 ng mL-1, overall good precision (CV < 20% for most of the PFAS) and a low uncertainty (< 30% of relative expanded deviation, k = 2). The method was further validated both with the NIST plasma Standard Reference Material 1950, showing that the accuracy of the provided results was between 63%-101%, and by the proficiency test arranged by the Arctic Monitoring Assessment Program (AMAP, 2022) obtaining satisfactory results within 95% confidence interval of the assigned value.

Nontarget Identification of Novel Per- and Polyfluoroalkyl Substances (PFAS) in Soils from an Oil Refinery in Southwestern China: A Combined Approach with TOP Assay

Oil refinery activity can be an emission source of perfluoroalkyl and polyfluoroalkyl substances (PFAS) to the environment, while the contamination profiles in soils remain unknown. This study investigated 44 target PFAS in soil samples collected from an oil refinery in Southeastern China, identified novel PFAS, and characterized their behaviors by assessing their changes before and after employing advanced oxidation using a combination of nontarget analysis and a total oxidizable precursor (TOP) assay. Thirty-four target PFAS were detected in soil samples. Trifluoroacetic acid (TFA) and hexafluoropropylene oxide dimer acid (HFPO-DA) were the dominant PFAS. Twenty-three novel PFAS of 14 classes were identified, including 8 precursors, 11 products, and 4 stable PFAS characterized by the TOP assay. Particularly, three per-/polyfluorinated alcohols were identified for the first time, and hexafluoroisopropanol (HFIP) quantified up to 657 ng/g dw is a novel precursor for TFA. Bistriflimide (NTf2) potentially associated with an oil refinery was also reported for the first time in the soil samples. This study highlighted the advantage of embedding the TOP assay in nontarget analysis to reveal not only the presence of unknown PFAS but also their roles in environmental processes. Overall, this approach provides an efficient way to uncover contamination profiles of PFAS especially in source-impacted areas.

Nontarget Screening and Fate of Emerging Per- and Polyfluoroalkyl Substances in Wastewater Treatment Plants in Tianjin, China

Wastewater treatment plants (WWTPs) are typical point sources of per- and polyfluoroalkyl substances (PFAS) released into the environment. The suspect and nontarget screening based on gas chromatography or liquid chromatography-high resolution mass spectrometry were performed on atmosphere, wastewater, and sludge samples collected from two WWTPs in Tianjin to discover emerging PFAS and their fate in this study. A total of 40 PFAS (14 neutral and 26 ionic) and 64 PFAS were identified in the atmosphere and wastewater/sludge, respectively, among which 5 short-chain perfluoroalkyl sulfonamide derivatives, 4 ionic PFAS, and 15 aqueous film-forming foam-related cationic or zwitterionic PFAS have rarely or never been reported in WWTPs in China. Active air sampling is more conducive to the enrichment of emerging PFAS, while passive sampling is inclined to leave out some ultrashort-chain PFAS or unstable transformation intermediates. Moreover, most precursors and intermediates could be enriched in the atmosphere at night, while the PFAS associated with aerosols with high water content or particles enter the atmosphere easily during the day. Although most emerging PFAS could not be eliminated efficiently in conventional treatment units, deep bed filtration and advanced oxidation processes could partly remove some emerging precursors.

Identifying priority PBT-like compounds from emerging PFAS by nontargeted analysis and machine learning models

As traditional per and polyfluoroalkyl substances (PFAS) are phased out, emerging PFAS are being developed and widely used. However, little is known about their properties, including persistence, bioaccumulation, and toxicity (PBT). Screening for emerging PFAS relies on available chemical inventory databases. Here, we compiled a database of emerging PFAS obtained from nontargeted analysis and assessed their PBT properties using machine learning models, including qualitative graph attention networks, Insubria PBT Index and quantitative EAS-E Suite, VEGA, and ProTox-II platforms. Totally 282 homologues (21.8% of emerging PFAS) were identified as PBT based on the combined qualitative and quantitative prediction, in which 140 homologues were detected in industrial and nonbiological/biological samples, belong to four categories, i.e. modifications of perfluoroalkyl carboxylic acids, perfluoroalkane sulfonamido substances, fluorotelomers and modifications of perfluoroalkyl sulfonic acids. Approximately 10.1% of prioritized emerging PFAS were matched to chemical vendors and 19.6% to patents. Aqueous film-forming foams and fluorochemical factories are the predominant sources for prioritized emerging PFAS. The database and screening results can update the assessment related to legislative bodies such as the US Toxic Substances Control Act and the Stockholm Convention. The combined qualitative and quantitative machine learning models can provide a methodological tool for prioritizing other emerging organic contaminants.

Target and non-target analyses of neutral per- and polyfluoroalkyl substances from fluorochemical industries using GC-MS/MS and GC-TOF: Insights on their environmental fate

Novel and emerging per- and polyfluoroalkyl substances (PFAS) are a key issue of concern in global environmental studies. In this study, air, sediment, and wastewater samples were collected from areas in and/or surrounded by fluorochemical-related industrial facilities to characterize the contamination profiles of neutral and novel PFAS (n-PFAS) using a gas chromatograph-based target and non-target analyses. Fluorotelomer alcohols were predominant in the samples, accounting for 80 % of the n-PFAS, followed by fluorotelomer acrylates. Air samples collected proximate to the durable water repellent (DWR) facility had the highest concentration of n-PFAS, which was approximately two orders of magnitude higher than those found in others. Non-target analysis identified fluorotelomer iodides and fluorotelomer methacrylate in multiple matrices near DWR facilities, indicating significant contamination of n-PFAS. Levels of both C6- and C8-based PFAS reflected a shift in usage patterns from C8- to C6-based fluorochemicals. Matrix-dependent profiles of n-PFAS revealed that shorter-chain (e.g., C6) and longer-chain (>C8) PFAS were predominant in air and sediment, respectively, implying that air and sediment are mobile and secondary sources of PFAS. Untreated and treated industrial wastewater also contained n-PFAS and their transformation products. The findings shed light on our understanding of the multi-matrix distribution and transport of PFAS.

Non-targeted identification and semi-quantitation of emerging per- and polyfluoroalkyl substances (PFAS) in US rainwater

High-resolution mass spectrometry was used to screen for emerging per- and polyfluorinated alkyl substances (PFAS) in precipitation samples collected in summer 2019 at seven sites in the United States. We previously quantified the concentration of ten PFAS in the rainwater samples using the method of isotopic dilution (Pike et al., 2021). Nine of these targeted analytes belonged to the U.S. Environmental Protection Agency Regional Screening Level list, herein referred to as EPA-monitored analytes. In this new work, we identify emerging PFAS compounds by liquid chromatography quadrupole time-of-flight mass spectrometry. Several emerging PFAS were detected across all samples, with the most prevalent compounds being C3-C8 hydrogen-substituted perfluorocarboxylic acids (H-PFCAs) and fluorotelomer carboxylic acids (FTCAs). Concentrations of emerging PFAS were in the 10-1000 ng L-1 range (approximately 1-2 orders of magnitude greater than EPA-monitored PFAS) at all sites except Wooster, OH, where concentrations were even higher, with a maximum estimated ΣPFAS of 16 400 ng L-1. The elevated levels of emerging PFAS in the Wooster samples were predominantly even and odd chain-length H-PFCAs and FTCAs comprised of complex mixtures of branched isomers. This unique composition did not match any known manufactured PFAS formulation reported to date, but it could represent thermally transformed by-products emitted by a local point source. Overall, the results indicate that PFAS outside of the standard analyte lists make up a significant and previously unappreciated fraction of contaminants in rainwater collected within the central U.S.-and potentially world-wide-especially in proximity to localized point sources.

Nontarget Analysis and Comprehensive Characterization of Iodinated Polyfluoroalkyl Acids in Wastewater and River Water by LC-HRMS with Cascade Precursor-Ion Exclusions and Algorithmic Approach

Poly- and perfluoroalkyl acids (PFAAs) are a large family of widespread contaminants of worldwide concern and well-known as "forever chemicals". Direct emission of PFAAs from the fluorochemical industry is a crucial source of PFAA pollutants in the environment. This study implemented nontarget analysis and comprehensive characterization for a category of new PFAA contaminants, i.e., iodinated PFAAs (IPFAAs), in fluorochemical industry wastewater and relevant contaminated river water by liquid chromatography-high-resolution mass spectrometry with a cascade precursor ion exclusion (PIE) strategy and in-house developed data extraction and processing algorithms. A total of 26 IPFAAs (including 2 isomers of an IPFAA) were found and identified with tentative molecular structures. Semiquantification of the IPFAAs was implemented, and the total concentrations of IPFAAs were 0.16-285.52 and 0.15-0.17 μg/L in wastewater and river water, respectively. The high concentrations in association with the predicted ecotoxicities and environmental behaviors demonstrate that these IPFAAs are worthy of more concern and further in-depth research. The cascade PIE strategy along with the data extraction and processing algorithms can be extended to nontarget analysis for other pollutants beyond IPFAAs. The nontarget identification and characterization outcomes provide new understanding on the environmental occurrence and pollution status of IPFAAs from a comprehensive perspective.

SWATH-F: A Novel Nontarget Strategy Based on the SWATH-MS Deconvolution Method Assisting in Annotating PFAS Homologues in Multisample Studies

In order to identify emerging per- and polyfluoroalkyl substances (PFASs) and their alternatives in the environment or population, we need to perform extensive profiling of PFASs to determine their distribution in samples. The sequential window acquisition of all theoretical fragment-ion spectra (SWATH mode) is capable of obtaining a wide range of MS2 spectra but is difficult for direct identification of PFASs due to its complex MS2 spectra, and the nontarget screening method is difficult to identify due to its lack of a priori information. In this study, we demonstrated the great potential of SWATH-F, a nontarget fragment-based homologue screening method in combination with the SWATH-MS deconvolution, for detecting PFASs. We evaluated the application of SWATH-F to gradient spiked samples and real population serum samples, compared it with nontarget homologue screening in the information-dependent acquisition mode (IDA mode), and obtained better results for SWATH-F with 276% improvement (IDA:17 PFASs, SWATH-F: 64 PFASs) in identification. In addition, we automated the screening and identification process of SWATH-F to facilitate its use by researchers. SWATH-F is freely available on GitHub (https://github.com/njuIrene/SWATH-F) under an MIT license.

Per- and polyfluoroalkyl substances in ambient fine particulate matter in the Pearl River Delta, China: Levels, distribution and health implications

Per- and polyfluoroalkyl substances (PFAS) have attracted worldwide attention as one of persistent organic pollutants; however, there is limited knowledge about the exposure concentrations of PFAS-contained ambient particulate matter and the related health risks. This study investigated the abundance and distribution of 32 PFAS in fine particulate matter (PM2.5) collected from 93 primary or secondary schools across the Pearl River Delta region (PRD), China. These chemicals comprise four PFAS categories which includes perfluoroalkyl carboxylic acids (PFCAs), perfluoroalkyl sulfonic acids (PFSAs), perfluoroalkyl acid (PFAA) precursors and PFAS alternatives. In general, concentrations of target PFAS ranged from 11.52 to 419.72 pg/m3 (median: 57.29 pg/m3) across sites. By categories, concentrations of PFSAs (median: 26.05 pg/m3) were the dominant PFAS categories, followed by PFCAs (14.25 pg/m3), PFAS alternatives (2.75 pg/m3) and PFAA precursors (1.10 pg/m3). By individual PFAS, PFOS and PFOA were the dominant PFAS, which average concentration were 24.18 pg/m3 and 6.05 pg/m3, respectively. Seasonal variation showed that the concentrations of PFCAs and PFSAs were higher in winter than in summer, whereas opposite seasonal trends were observed in PFAA precursors and PFAS alternatives. Estimated daily intake (EDI) and hazard quotient (HQ) were used to assess human inhalation-based exposure risks to PFAS. Although the health risks of PFAS via inhalation were insignificant (HQ far less than one), sufficient attention should be levied to ascertain the human exposure risks through inhalation, given that exposure to PFAS through air inhalation is a long term and cumulative process.

Can oral toxicity data for PFAS inform on toxicity via inhalation?

Per- and poly-fluoroalkyl substances (PFAS) are ubiquitous in the environment and are detected in wildlife and humans. With respect to human exposure, studies have shown that ingestion is the primary route of exposure; however, in certain settings, exposure via inhalation could also be a significant source of exposure. While many studies examined toxicity of PFAS via ingestion, limited information is available for PFAS toxicity via the inhalation route, translating into a lack of exposure guidelines. Consequently, this article examined whether route-to-route extrapolation to derive guidelines for inhalation exposure is appropriate for PFAS. Perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid (PFOS) were used as exemplary PFAS given the abundance of toxicity data for these two compounds. Our evaluation determined that available toxicity and toxicokinetic data support route-to-route extrapolation for PFAS in order to derive inhalation-based standards. Results from this analysis suggest that an air concentration of 7.0 × 10-5  mg/m3 (or 0.07 μg/m3 ) would be an appropriate RfC for PFOA and PFOS assuming the 2016 EPA RfD of 0.00002 mg/kg-day, whereas use of the interim RfDs proposed in 2022 of 1.5 × 10-9 and 7.9 × 10-9  mg/kg would yield much lower RfCs of 5.25 × 10-9 and 2.77 × 10-8  mg/m3 (or 5.25 × 10-6 and 2.77 × 10-5 μg/m3 ) for PFOA and PFOS, respectively.

Analytical approaches for screening of per- and poly fluoroalkyl substances in food items: A review of recent advances and improvements

Per and polyfluoroalkyl substances (PFAS) are a group of man-made chemicals characterized by their ubiquitous nature in all environmental compartments which makes them of increasing concern due to their persistence, bioaccumulation, and toxicity (PBT). Several instrumental methodologies and separation techniques have been identified in the literature for the detection and quantification of PFAS in environmental samples. In this review, we have identified and compared common separation techniques adopted for the extraction of PFAS in food items, and analytical methodologies for identification and quantification of PFAS in food items of plant and animal origin, highlighting recent advances in tandem techniques for the high selectivity and separation of PFAS related compounds as well as knowledge gaps and research needs on current analytical methodologies.

Trends in the Analysis and Exploration of per- and Polyfluoroalkyl Substances (PFAS) in Environmental Matrices: A Review

Per- and polyfluoroalkyl substances (PFAS) is an emerging class of organic pollutants of concern and is now prevalent in environmental matrices including water, soil, air, and biological. So far, several standard analytical methods have been developed to systematically analyze PFAS in different environmental matrices. However, the complexity of environmental matrices makes the effective extraction of PFAS difficult, and the legacy PFAS is gradually changing into a new PFAS with short chain and unknown structure in production, which makes the analysis of PFAS challenging. In this review, the following aspects are summarized: (1) the advances in standard analytical methods for PFAS in different environmental matrices, and further generalizes the updating novel extraction and detection methods; (2) the analysis of unknown PFAS, the suspect and non-targeted screening analysis method of PFAS based on high-resolution mass spectrometry (HRMS) is systematically described.

Practical application guide for the discovery of novel PFAS in environmental samples using high resolution mass spectrometry

BACKGROUND

The intersection of the topics of high-resolution mass spectrometry (HRMS) and per- and polyfluoroalkyl substances (PFAS) bring together two disparate and complex subjects. Recently non-targeted analysis (NTA) for the discovery of novel PFAS in environmental and biological media has been shown to be valuable in multiple applications. Classical targeted analysis for PFAS using LC-MS/MS, though growing in compound coverage, is still unable to inform a holistic understanding of the PFAS burden in most samples. NTA fills at least a portion of this data gap.

OBJECTIVES

Entrance into the study of novel PFAS discovery requires identification techniques such as HRMS (e.g., QTOF and Orbitrap) instrumentation. This requires practical knowledge of best approaches depending on the purpose of the analyses. The utility of HRMS applications for PFAS discovery is unquestioned and will likely play a significant role in many future environmental and human exposure studies.

METHODS/RESULTS

PFAS have some characteristics that make them standout from most other chemicals present in samples. Through a series of tell-tale PFAS characteristics (e.g., characteristic mass defect range, homologous series and characteristic fragmentation patterns), and case studies different approaches and remaining challenges are demonstrated.

IMPACT STATEMENT

The identification of novel PFAS via non-targeted analysis using high resolution mass spectrometry is an important and difficult endeavor. This synopsis document will hopefully make current and future efforts on this topic easier to perform for novice and experienced alike. The typical time devoted to NTA PFAS investigations (weeks to months or more) may benefit from these practical steps employed.

The novel polyfluoroalkyl benzenesulfonate OBS exposure induces cell cycle arrest and senescence of rat pituitary cell GH3 via the p53/p21/RB pathway

Sodium p-perfluorous nonenoxybenzene sulfonate (OBS), an economical alternative to perfluorooctane sulfonate (PFOS) in multiple industrial fields, is widely detected in the environment. The toxicity of OBS has received increasing attention. Pituitary cells are components of the endocrine system and act as vital regulators of homeostatic endocrine balance. However, the effects of OBS on pituitary cells remain unknown. The present study explores the effects of OBS (0.5, 5, and 50 μM) on GH3 rat pituitary cells after treatment for 24, 48, and 72 h. We found that OBS significantly inhibited cell proliferation in GH3 cells with remarkable senescent phenotypes, including enhanced SA-β-gal activity and expression of senescence-associated secretory phenotype (SASP)-related genes, cell cycle arrest, and upregulation of the senescence-related proteins γ-H2A.X and Bcl-2. OBS caused significant cell cycle arrest of GH3 cells at the G1-phase and concomitantly downregulated the expression of some key proteins for the G1/S transition, including cyclin D1 and cyclin E1. Consistently, the phosphorylation of retinoblastoma (RB), which plays a central role in regulating the cell cycle, was prominently reduced after OBS exposure. Furthermore, OBS notably activated the p53-p21 signalling pathway in GH3 cells, as evidenced by increased p53 and p21 expressions, enhanced p53 phosphorylation, and augmented p53 nuclear import. To our knowledge, this study is the first to reveal that OBS triggers senescence in pituitary cells via the p53-p21-RB signalling pathway. Our study demonstrates a novel toxic effect of OBS in vitro, and provides new perspectives for understanding the potential toxicity of OBS.

Integration of target, suspect, and nontarget screening with risk modeling for per- and polyfluoroalkyl substances prioritization in surface waters

Though thousands of per- and polyfluoroalkyl substances (PFAS) have been on the global market, most research focused on only a small fraction, potentially resulting in underestimated environmental risks. Here, we used complementary target, suspect, and nontarget screening for quantifying and identifying the target and nontarget PFAS, respectively, and developed a risk model considering their specific properties to prioritize the PFAS in surface waters. Thirty-three PFAS were identified in surface water in the Chaobai river, Beijing. The suspect and nontarget screening by Orbitrap displayed a sensitivity of > 77%, indicating its good performance in identifying the PFAS in samples. We used triple quadrupole (QqQ) under multiple-reaction monitoring for quantifying PFAS with authentic standards due to its potentially high sensitivity. To quantify the nontarget PFAS without authentic standards, we trained a random forest regression model which presented the differences up to only 2.7 times between measured and predicted response factors (RFs). The maximum/minimum RF in each PFAS class was as high as 1.2-10.0 in Orbitrap and 1.7-22.3 in QqQ. A risk-based prioritization approach was developed to rank the identified PFAS, and four PFAS (i.e., perfluorooctanoic acid, hydrogenated perfluorohexanoic acid, bistriflimide, 6:2 fluorotelomer carboxylic acid) were flagged with high priority (risk index > 0.1) for remediation and management. Our study highlighted the importance of a quantification strategy during environmental scrutiny of PFAS, especially for nontarget PFAS without standards.

High density polyethylene (HDPE) and thermoplastic polyurethane (TPU) wristbands as personal passive samplers monitoring per- and polyfluoroalkyl substances (PFASs) exposure to postgraduate students

Per- and polyfluoroalkyl substances (PFASs) present adverse effects for human health, which result in strong needs for reliable tools monitoring personal exposure to PFASs. This study manufactured two wristbands of high density polyethylene (HDPE) and thermoplastic polyurethane (TPU), and used the wristbands to monitor PFASs personal exposure. The analytical method was developed to measure 32 PFASs in the paired HDPE and TPU wristbands worn by 60 postgraduates. Twenty-nine of 32 PFASs were detected and hexafluoropropylene oxide dimer acid (HFPO-DA) was predominant individual PFASs with median concentrations of 337 and 554 pg/g for HDPE and TPU wristbands respectively. The gender and grade of students had moderate effects on PFASs distribution in the wristbands. Higher PFASs levels were determined in the two wristbands worn by the male students compared to the females, and the greatest PFASs concentration was observed in the wristbands worn by the first-year postgraduates, follow by second- and third-year postgraduates. Additionally, significant correlations between paired HDPE and TPU wristbands were observed for perfluorobutanoic acid (PFBA), perfluorohexane sulfonic acid (PFHxS), perfluoroheptane sulfonic acid (PFHpS), perfluorooctane sulfonic acid (PFOS), and HFPO-DA. These results suggest that HDPE and TPU wristbands can be used as effective tools for monitoring personal PFAS exposure.