Cross-Links-Entanglements Integrated Networks Contributing to Highly Resilient, Soft, and Self-Adhesive Elastomers with Low Hysteresis for Green Wearable Electronics

Enclose Biobased Content into Polyurethane Elastomers: A Summary of Synthetic Routes and an Inverse Prediction of their Percentages

Biobased polyurethane elastomers (BPUEs) got vigorous exploration in recent decade, clarifying how biobased content affect their mechanical and thermal properties becomes critical. Here, a comprehensive BPUE dataset with 506 splines associated with a brief summary for the transformation of biobased content into polyurethane are presented. Distributions for typical mechanical and thermal properties including Young's modulus, tensile strength, elongation at break, and glass transition temperature (Tg) are clarified. A linear relationship Tg DMA = 0.98*Tg + 19.43K is found for Tg's measured by differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). Then, a binary classification model with an accuracy of 0.80 to distinguish PUEs with and without biobased content, and a regression model with the coefficient of determination of 0.89 to predict the mass percentage of biobased content (BBC%) are constructed. Based on these predictive models, important correlations are observed, including the strong dependence of Tg and tanδ on BBC%, and the weak preference to use longer spline in tensile test, lower heating rates in DSC and DMA measurements for BPUEs with higher BBC%. These inverse predictive models provide a cost-effective way to quantify the biobased content in PUE products, without prior knowledge of their exact composition and formulas.

Low-Hysteresis and Tough Ionogels via Low-Energy-Dissipating Cross-Linking

Low-hysteresis merits can help polymeric gel materials survive from consecutive loading cycles and promote life span in many burgeoning areas. However, it is a big challenge to design low-hysteresis and tough polymeric gel materials, especially for ionogels. This can be attributed to the fact that higher viscosities of ionic liquids (ILs) would increase chain friction of polymeric gels and eventually dissipate large amounts of energy under deformation. Herein, a chemical design of ionogels is proposed to achieve low-hysteresis characteristics in both mechanical and electric aspects via hierarchical aggregates formed by supramolecular self-assembly of quadruple H-bonds in a soft IL-rich polymeric matrix. These self-assembled nanoaggregates not only can greatly reinforce the polymeric matrix and enhance resilience, but also exhibit low-energy-dissipating features under stress conditions, simultaneously benefiting for low-hysteresis properties. These aggregates can also promote toughness and subsequent anti-fatigue properties in response to external cyclic mechanical stimuli. More importantly, these ionogels are presented as a model system to elucidate the underlying mechanism of the low hysteresis and fatigue resistance. Based on these findings, it is further demonstrated that the supramolecular low-hysteresis strategy is universal.

Thermally Conductive Elastomer Composites with High Toughness, Softness, and Resilience Enabled by Regulating Interfacial Structure and Dynamics

The emerging applications of thermally conductive elastomer composites in modern electronic devices for heat dissipation require them to maintain both high toughness and resilience under thermomechanical stresses. However, such a combination of thermal conductivity and desired mechanical characteristics is extremely challenging to achieve in elastomer composites. Here this long-standing mismatch is resolved via regulating interfacial structure and dynamics response. This regulation is realized both by tuning the molecular weight of the dangling chains in the polymer networks and by silane grafting of the fillers, thereby creating a broad dynamic-gradient interfacial region comprising of entanglements. These entanglements can provide the slipping topological constraint that allows for tension equalization between and along the chains, while also tightening into rigid knots to prevent chain disentanglement upon stretching. Combined with ultrahigh loading of aluminum-fillers (90 wt%), this design provides a low Young's modulus (350.0 kPa), high fracture toughness (831.5 J m-2), excellent resilience (79%) and enhanced thermal conductivity (3.20 W m-1 k-1). This work presents a generalizable preparation strategy toward engineering soft, tough, and resilient high-filled elastomer composites, suitable for complex environments, such as automotive electronics, and wearable devices.

Ductile adhesive elastomers with force-triggered ultra-high adhesion strength

Elastomers play a vital role in many forthcoming advanced technologies in which their adhesive properties determine materials' interface performance. Despite great success in improving the adhesive properties of elastomers, permanent adhesives tend to stick to the surfaces prematurely or result in poor contact depending on the installation method. Thus, elastomers with on-demand adhesion that is not limited to being triggered by UV light or heat, which may not be practical for scenarios that do not allow an additional external source, provide a solution to various challenges in conventional adhesive elastomers. Herein, we report a novel, ready-to-use, ultra high-strength, ductile adhesive elastomer with an on-demand adhesion feature that can be easily triggered by a compression force. The precursor is mainly composed of a capsule-separated, two-component curing system. After a force-trigger and curing process, the ductile adhesive elastomer exhibits a peel strength and a lap shear strength of 1.2 × 104 N m-1 and 7.8 × 103 kPa, respectively, which exceed the reported values for advanced ductile adhesive elastomers. The ultra-high adhesion force is attributed to the excellent surface contact of the liquid-like precursor and to the high elastic modulus of the cured elastomer that is reinforced by a two-phase design. Incorporation of such on-demand adhesion into an elastomer enables a controlled delay between installation and curing so that these can take place under their individual ideal conditions, effectively reducing the energy cost, preventing failures, and improving installation processes.

Multifunctional soybean protein isolate-graft-carboxymethyl cellulose composite as all-biodegradable and mechanically robust mulch film for "green" agriculture

Multifunctional mulch films with robust mechanical behaviors of biopolymer-based biodegradable mulch materials were highly demanded in promoting the development of "green" agriculture. Herein, a sort of mechanically robust and all-biodegradable soybean protein isolate-graft‑sodium carboxymethyl cellulose composite mulch film was innovatively proposed through the amidation reactions between -COOH on protonated sodium carboxymethyl cellulose and -NH2 on soybean protein isolate. Arising from the reinforced intermolecular interactions upon chemical covalent bonds and physical hydrogen bonds, the maximum tensile strength and the elongation at break were increased from 10.61 MPa and 20.67 % for sodium carboxymethyl cellulose film to 42.15 MPa and 24.8 % for the optimized soybean protein isolate-graft‑sodium carboxymethyl cellulose composite mulch film, respectively. In addition, experimental results showed that the optimized soybean protein isolate-graft‑sodium carboxymethyl cellulose composite mulch film possesses soil moisture retention and controlled urea release properties. When employed as mulch film in practice, the cabbage seed presents higher germination when soil was covered with this versatile mulch film compared to commercial low-density polyethylene mulch film. Our discoveries build a prototype for the manufacture of eco-friendly mulch films with high mechanical strength, soil moisture retention, controlled urea release features.

Recent Progress in Advanced Polyester Elastomers for Tissue Engineering and Bioelectronics

Polyester elastomers are highly flexible and elastic materials that have demonstrated considerable potential in various biomedical applications including cardiac, vascular, neural, and bone tissue engineering and bioelectronics. Polyesters are desirable candidates for future commercial implants due to their biocompatibility, biodegradability, tunable mechanical properties, and facile synthesis and fabrication methods. The incorporation of bioactive components further improves the therapeutic effects of polyester elastomers in biomedical applications. In this review, novel structural modification methods that contribute to outstanding mechanical behaviors of polyester elastomers are discussed. Recent advances in the application of polyester elastomers in tissue engineering and bioelectronics are outlined and analyzed. A prospective of the future research and development on polyester elastomers is also provided.

Scalable and Degradable Dextrin-Based Elastomers for Wearable Touch Sensing

Elastomer-based wearables can improve people's lives; however, frictional wear caused by manipulation may pose significant concerns regarding their durability and sustainability. To address the aforementioned issue, a new class of advanced scalable supersoft elastic transparent material (ASSETm) is reported, which offers a unique combination of scalability (20 g scale), stretchability (up to 235%), and enzymatic degradability (up to 65% in 30 days). The key feature of our design is to render native dextrin hydrophobic, which turns it into a macroinitiator for bulk ring-opening polymerization. Based on ASSETm, a self-powered touch sensor (ASSETm-TS) for touch sensing and non-contact approaching detection, possessing excellent electrical potential (up to 65 V) and rapid response time (60 ms), is fabricated. This work is a step toward developing sustainable soft electronic systems, and ASSETm's tunability enables further improvement of electrical outputs, enhancing human-interactive applications.

Recent development of biodegradable synthetic rubbers and bio-based rubbers using sustainable materials from biological sources

Rubber is an amorphous hyperelastic polymer which is widely used in this modern era. Natural rubber is considered the ultimate rubber in terms of mechanical performance, but over the years, some limitations and challenges in natural rubber cultivation that could result in serious shortages in the supply chain had been identified. Since then, the search for alternatives including new natural and synthetic rubbers has been rather intense. The initiative to explore new sources of natural rubber which started during the 1940s has been reignited recently due to the increasing demand for natural rubber. The commercialization of natural rubber from the Parthenium argentatum and Taraxacum kok-saghyz species, with the cooperation from rubber product manufacturing companies, has somewhat improved the sustainability of the natural rubber supply chain. Meanwhile, the high demand for synthetic rubber drastically increases the rate of depletion of fossil fuels and amplifies the adverse environmental effect of overexploitation of fossil fuels. Moreover, rubber and plastic products disposal have been a major issue for many decades, causing environmental pollution and the expansion of landfills. Sustainable synthetic rubber products could be realized through the incorporation of materials from biological sources. They are renewable, low cost, and most importantly, biodegradable in nature. In this review, brief introduction to natural and synthetic rubbers, challenges in the rubber industry, alternatives to conventional natural rubber, and recent advances in biodegradable and/or bio-based synthetic rubbers are discussed. The effect of incorporating various types of biologically sourced materials in the synthetic rubbers are also elaborated in detail.

Green and Integrated Wearable Electrochemical Sensor for Chloride Detection in Sweat

Wearable sensors for sweat biomarkers can provide facile analyte capability and monitoring for several diseases. In this work, a green wearable sensor for sweat absorption and chloride sensing is presented. In order to produce a sustainable device, polylactic acid (PLA) was used for both the substrate and the sweat absorption pad fabrication. The sensor material for chloride detection consisted of silver-based reference, working, and counter electrodes obtained from upcycled compact discs. The PLA substrates were prepared by thermal bonding of PLA sheets obtained via a flat die extruder, prototyped in single functional layers via CO₂ laser cutting, and bonded via hot-press. The effect of cold plasma treatment on the transparency and bonding strength of PLA sheets was investigated. The PLA membrane, to act as a sweat absorption pad, was directly deposited onto the membrane holder layer by means of an electrolyte-assisted electrospinning technique. The membrane adhesion capacity was investigated by indentation tests in both dry and wet modes. The integrated device made of PLA and silver-based electrodes was used to quantify chloride ions. The calibration tests revealed that the proposed sensor platform could quantify chloride ions in a sensitive and reproducible way. The chloride ions were also quantified in a real sweat sample collected from a healthy volunteer. Therefore, we demonstrated the feasibility of a green and integrated sweat sensor that can be applied directly on human skin to quantify chloride ions.