Enhanced Electrochemical and Photocatalytic Performance of Core-Shell CuS@Carbon Quantum Dots@Carbon Hollow Nanospheres

Construction and application of NiCo2O4@MnS composite with hierarchical structure for hybrid supercapacitor

The development of an electrochemical energy storage system with exceptional performance is an important way to address the energy crisis and environmental pollution of the modem world. In this study, an NiCo2O4@MnS composite with a unique hierarchical structure has been successfully synthesized on an NF substrate using the hydrothermal-electrodeposition method. The results indicate that NiCo2O4@MnS possesses superior specific capacitance and excellent cycling stability. At a current density of 2 A g-1, its specific capacitance can reach 2100 F g-1, while the capacitance retention is still 76% after 10 000 cycles at 10 A g-1. Moreover, when the current density is 1 A g-1, the assembled NiCo2O4@MnS//AC device can deliver a specific capacitance of 203 F g-1, and the energy density is up to 55 W h kg-1 at a power density of 697 W kg-1. These outstanding electrochemical properties of NiCo2O4@MnS can be ascribed to the increase in ion diffusion, specific surface area and electronic conductivity due to its unique hierarchical structure and introduction of MnS.

Application of Copper-Sulfur Compound Electrode Materials in Supercapacitors

Supercapacitors (SCs) are a novel type of energy storage device that exhibit features such as a short charging time, a long service life, excellent temperature characteristics, energy saving, and environmental protection. The capacitance of SCs depends on the electrode materials. Currently, carbon-based materials, transition metal oxides/hydroxides, and conductive polymers are widely used as electrode materials. However, the low specific capacitance of carbon-based materials, high cost of transition metal oxides/hydroxides, and poor cycling performance of conductive polymers as electrodes limit their applications. Copper-sulfur compounds used as electrode materials exhibit excellent electrical conductivity, a wide voltage range, high specific capacitance, diverse structures, and abundant copper reserves, and have been widely studied in catalysis, sensors, supercapacitors, solar cells, and other fields. This review summarizes the application of copper-sulfur compounds in SCs, details the research directions and development strategies of copper-sulfur compounds in SCs, and analyses and summarizes the research hotspots and outlook, so as to provide a reference and guidance for the use of copper-sulfur compounds.

Chemical- and green-precursor-derived carbon dots for photocatalytic degradation of dyes

Rapid industrialization and untreated industrial effluents loaded with toxic and carcinogenic contaminants, especially dyes that discharge into environmental waters, have led to a rise in water pollution, with a substantial adverse impact on marine life and humankind. Photocatalytic techniques are one of the most successful methods that help in degradation and/or removal of such contaminants. In recent years, semiconductor quantum dots are being substituted by carbon dots (CDs) as photocatalysts, due to the ease of formation, cost-effectiveness, possible sustainability and scalability, much lower toxicity, and above all its high capacity to harvest sunlight (UV, visible, and near infrared) through electron transfer that enhances the lifetime of the photogenerated charge carriers. A better understanding between the properties of the CDs and their role in photocatalytic degradation of dyes and contaminants is required for the formation of controllable structures and adjustable outcomes. The focus of this review is on CDs and its composites as photocatalysts obtained from different sustainable green as well as chemical precursors. Apart from the synthesis, characterization, and properties of the CDs, the study also highlights the effect of different parameters on the photocatalytic properties of CDs and their composites for catalytic dye degradation mechanisms in detail. Besides the present research development in the field, potential challenges and future perspectives are also presented.

Enhanced Photothermal Effect Assisted by Resonance Energy Transfer in Carbon/Covellite Core-Shell Nanoparticles toward a High-Performance Interfacial Water Evaporation Process

Carbon and semiconductor nanoparticles are promising photothermal materials for various solar-driven applications. Inevitable recombination of photoinduced charge carriers in a single constituent, however, hinders the realization of a greater photothermal effect. Core-shell heterostructures utilizing the donor-acceptor pair concept with high-quality interfaces can inhibit energy loss from the radiation relaxation of excited species, thereby enhancing the photothermal effect. Here, core-shell structures composed of a covellite (CuS) shell (acceptor) and spherical carbon nanoparticle (CP) core (donor) (abbreviated as CP/CuS) are proposed to augment the photothermal conversion efficiency via the Förster resonance energy transfer (FRET) mechanism. The close proximity and spectral overlap of the donor and acceptor trigger the FRET mechanism, where the electronic excitation relaxation energy of the CP reinforces the plasmonic resonance and near-infrared absorption in CuS, resulting in boosting the overall photothermal conversion efficiency. CP/CuS core-shell coated on polyurethane (PU) foam exhibits a total solar absorption of 97.1%, leading to an elevation in surface temperature of 61.6 °C in dry conditions under simulated solar illumination at a power density of 1 kW m-2 (i.e., 1 sun). Leveraging the enhanced photothermal conversion emanated from the energy transfer effect in the core-shell structure, CP/CuS-coated PU foam achieves an evaporation rate of 1.62 kg m-2 h-1 and an energy efficiency of 93.8%. Thus, amplifying photothermal energy generation in core-shell structures via resonance energy transfer can be promising in solar energy-driven applications and thus merits further exploration.

Construction of thickness-controllable bimetallic sulfides/reduced graphene oxide as a binder-free positive electrode for hybrid supercapacitors

Devices for electrochemical energy storage with exceptional capacitance and rate performance, outstanding energy density, simple fabrication, long-term stability, and remarkable reversibility have always been in high demand. Herein, a high-performance binder-free electrode (3D NiCuS/rGO) was fabricated as a supercapacitor by a simple electrodeposition process on a Ni foam (NF) surface. The thickness of the deposited materials on the NF surface was adjusted by applying a low cycle number of cyclic voltammetry (5 cycles) which produced a thin layer and thus enabled the easier penetration of electrolytes to promote electron and charge transfer. The NiCuS was anchored by graphene layers producing nicely integrated materials leading to a higher electroconductivity and a larger surface area electrode. The as-fabricated electrode displayed a high specific capacitance (2211.029 F g-1 at 5 mV s-1). The NiCuS/rGO/NF//active carbon device can achieve a stable voltage window of 1.5 V with a highly specific capacitance of 84.3 F g-1 at a current density of 1 A g-1. At a power density of 749 W kg-1, a satisfactory energy density of 26.3 W h kg-1 was achieved, with outstanding coulombic efficiency of 100% and an admirable life span of 96.2% after 10 000 GCD cycles suggesting the significant potential of the as-prepared materials for practical supercapacitors.

Cu-doped SnS2 nanosheets with superior visible-light photocatalytic CO2 reduction performance

Photocatalytic CO₂ reduction utilizing solar energy is a clean, environment-friendly strategy converting CO₂ into hydrocarbon fuels to solve the energy crisis and climate issues. Herein, we report the synthesis of Cu-doped SnS₂ nanosheets via a simple hydrothermal method. The prepared Cu-doped SnS₂ composite displays superior photocatalytic CO₂ reduction activity. The optimized CH₃OH yield of the composite is two times higher than that of pure SnS₂. The enhanced photocatalytic performance is attributed to effective charge separation resulting from the thinner nanosheets and delocalization of electrons from SnS₂ to Cu, high visible light utilization efficiency, enlarged S_BET, negative shift of the flat-band potential and reduced charge transfer resistance with the introduction of Cu atoms. This work suggests the potential application of Cu-doped SnS₂ in photocatalytic CO₂ reduction.

In-situ synthesis of CuS@carbon nanocomposites and application in enhanced photo-fenton degradation of 2,4-DCP

Novel CuS nanoparticles embedded into carbon nanosheets (CuS@CNs) were prepared in situ by applying wheat straw cellulose/feather protein hydrogel beads as templates and were used to photocatalytically activate H₂O₂ to degrade 2,4-dichlorphenol (2,4-DCP). The photo-Fenton catalytic properties of the nanocomposite catalysts obtained under different synthetic conditions, including different Cu²⁺ concentrations, S^2- concentrations and calcination temperatures, were evaluated. The results showed that CuS@CNs with 0.1 M Cu²⁺, 0.1 M S^2- at 800 °C presented excellent photo-Fenton degradation performance for 2,4-DCP (25 mg/L) in the presence of H₂O₂ and could remove 90% of 2,4-DCP in 2.5 h. The water quality parameters (pH, Cl^-, HCO₃^-, H₂PO₄^- and SO₄^2-) exhibited different effects on the photocatalytic degradation process. The catalytic activity of the CuS@CNs used in the cycle could be recovered after thermal regeneration. Radical quenching and electron paramagnetic resonance (EPR) experiments confirmed that ·OH species were main active radicals contributing to the degradation of 2,4-DCP. The photocatalytic mechanism of CuS@CNs was also explored by photoelectrochemical (PEC) measurements and UV-vis diffuse reflectance spectroscopy (DRS). Incorporation of carbon nanosheets could significantly improve the separation of photogenerated charge carriers to stimulate pollutant degradation by CuS. Based on the detected intermediates, the degradation pathway of 2,4-DCP in the CuS@CNs/H₂O₂ reaction system was also proposed.

Enhanced Supercapacitor Performance and Electromagnetic Interference Shielding Effectiveness of CuS Quantum Dots Grown on Reduced Graphene Oxide Sheets

This study is focused on the preparation of the CuS/RGO nanocomposite via the hydrothermal method using GO and Cu-DTO complex as precursors. X-ray diffraction, Fourier-transform infrared spectroscopy, and Raman and X-ray photoelectron spectroscopy study revealed the formation of the CuS/RGO nanocomposite with improved crystallinity, defective nanostructure, and the presence of the residual functional group in the RGO sheet. The morphological study displayed the transformation of CuS from nanowire to quantum dots with the incorporation of RGO. The galvanostatic charge/discharge curve showed that the CuS/RGO nanocomposite (12 wt % Cu-DTO complex) has tremendous and outperforming specific capacitance of 3058 F g-1 at 1 A g-1 current density with moderate cycling stability (∼60.3% after 1000 cycles at 10 A g-1). The as-prepared nanocomposite revealed excellent improvement in specific capacitance, cycling stability, Warburg impedance, and interfacial charge transfer resistance compared to neat CuS. The fabricated nanocomposites were also investigated for their bulk DC electrical conductivity and EMI shielding ability. It was observed that the CuS/RGO nanocomposite (9 wt % Cu-DTO) exhibited a total electromagnetic shielding efficiency of 64 dB at 2.3 GHz following absorption as a dominant shielding mechanism. Such a performance is ascribed to the presence of interconnected networks and synergistic effects.

Copper sulfide nanoparticles with potential bifunctional properties: supercapacitor and photocatalysis

Pure hexagonal CuS nanoparticles with stable high capacitance and photocatalytic activity were obtained by a mild solvothermal method.

Remarkably efficient charge transfer through a double heterojunction mechanism by a CdS-SnS-SnS2/rGO composite with excellent photocatalytic performance under visible light

In this work, a novel CdS-SnS-SnS₂/rGO photocatalyst with two tin valence states (Ⅱ and IV) was successfully synthesized by a one-pot solvothermal method. For comparison, CdS-SnS₂/rGO (GCS2) with tin in only the IV valence state was made by the same method. Based on a series of characterizations, CdS, SnS and SnS₂ were shown to be successfully loaded onto the rGO surface. The introduction of rGO may increase charge carrier separation. The degradation efficiency increased gradually with increasing rGO loading content, and the optimum photocatalytic activity was observed at 6.0 wt% rGO loading content (GCS1), which achieved the efficient removal (84.46%) of ibuprofen over 60 min. Compared with GCS2, the CdS-SnS-SnS₂/rGO composite exhibited significantly improved photocatalytic performance, which can be ascribed to the formation of a double heterostructure. rGO worked as a transfer mediator to transfer electrons from the conduction band (CB) of SnS to the CB of SnS₂ at the heterointerface, which then flowed to the CB of CdS because of another heterojunction, further enhancing the separation efficiency of photogenerated carriers. Therefore, this study highlights a novel double heterojunction system with a facial preparation method, visible light response and good recyclability, which is beneficial for environmental remediation.

Preparation of Biomass-Based Carbon Dots with Aggregation Luminescence Enhancement from Hydrogenated Rosin for Biological Imaging and Detection of Fe3

Fluorescent carbon dots (CDs) have numerous important applications, but enhancing the fluorescence emission and overcoming fluorescence quenching are still big challenges. Here, fluorescence-enhanced carbon dots (named hr-CDs) were prepared from sustainable hydrogenated rosin, using a simple hydrothermal method in a water solvent. The hr-CDs were mainly composed of graphitized carbon cores with surface functional groups. With the increase in the concentration to hr-CDs aqueous solutions, the distance between the carbon cores decreased, which resulted in the formation of J aggregates and the enhanced blue fluorescence emission. Even in the solid state, the hr-CDs show fluorescence emission because the surface functional groups could prevent π-π stacking interactions between the carbon cores. The hr-CDs show excellent resistance to photobleaching under intense ultraviolet light (200 mW/cm²). Vibrations and rotations of graphitized carbon core are restricted by low temperature and high viscosity, leading to increased radiative transition and thus increase in fluorescence intensity. The pH value in the range of 3.99-9.87 and anions have little effect on the fluorescence emission of hr-CDs. The fluorescence emission of the hr-CDs was selectively quenched by Fe³⁺ and can thus be used to detect Fe³⁺. The hr-CDs also have good biocompatibility and show the same ability in cell nuclear staining as 4',6-diamidino-2-phenylindole (DAPI).

In Situ Construction of CNT/CuS Hybrids and Their Application in Photodegradation for Removing Organic Dyes

Herein, a coprecipitation method used to synthesize CuS nanostructures is reported. By varying the reaction time and temperature, the evolution of the CuS morphology between nanoparticles and nanoflakes was investigated. It was found that CuS easily crystallizes into sphere-/ellipsoid-like nanoparticles within a short reaction time (0.5 h) or at a high reaction temperature (120 °C), whereas CuS nanoflakes are readily formed at a low reaction temperature (20 °C) for a long time (12 h). Photodegradation experiments demonstrate that CuS nanoflakes exhibit a higher photodegradation performance than CuS nanoparticles for removing rhodamine B (RhB) from aqueous solution under simulated sunlight irradiation. Carbon nanotubes (CNTs) were further used to modify the photodegradation performance of a CuS photocatalyst. To achieve this aim, CNTs and CuS were integrated to form CNT/CuS hybrid composites via an in situ coprecipitation method. In the in situ constructed CNT/CuS composites, CuS is preferably formed as nanoparticles, but cannot be crystallized into nanoflakes. Compared to bare CuS, the CNT/CuS composites manifest an obviously enhanced photodegradation of RhB; notably, the 3% CNT/CuS composite with CNT content of 3% showed the highest photodegradation performance (η = 89.4% for 120 min reaction, kapp = 0.01782 min-1). To make a comparison, CuS nanoflakes and CNTs were mechanically mixed in absolute alcohol and then dried to obtain the 3% CNT/CuS-MD composite. It was observed that the 3% CNT/CuS-MD composite exhibited a slightly higher photodegradation performance (η = 92.4%, kapp = 0.0208 min-1) than the 3% CNT/CuS composite, which may be attributed to the fact that CuS maintains the morphology of nanoflakes in the 3% CNT/CuS-MD composite. The underlying enhanced photocatalytic mechanism of the CNT/CuS composites was systematically investigated and discussed.

Metal–organic framework templated fabrication of Cu7S4@Ni(OH)2 core–shell nanoarrays for high-performance supercapacitors

Core–cell Cu₇S₄@Ni(OH)₂ nanorod arrays were fabricated by using metal–organic frameworks as templates, and showed high specific capacitance, superior rate capacity and excellent cycling stability for supercapacitors.

Neuron-like hierarchical manganese sulfide@Cu2S core/shell arrays on Ni foam as an advanced electrode for an asymmetric supercapacitor

Neuron-like hierarchical manganese sulfide@Cu₂S core/shell arrays on Ni foam as an advanced electrode for an asymmetric supercapacitor.

Carbon fibers coated with urchin-like copper sulfide for nonenzymatic voltammetric sensing of glucose

Urchin-like CuS was grown on xanthan gum-derived carbon nanofibers to obtain a sensor for enzyme-free electrochemical sensing of glucose. The unique nanostructure of the sensor provides a large specific surface, more electrocatalytically active sites, and high electrical conductivity. The voltammetric response to glucose, best measured at around 57 mV (vs. Ag/AgCl (E/V)) in 0.1 M NaOH solution, covers two linear ranges, one from 0.1-125 μM, another from 0.16 to 1.2 mM. The sensitivity is quite high (23.7 μA mM^-1 cm^-2), and the detection limit is low (19 nM at S/N = 3). The sensor has high selectivity against potentially interfering molecules such as fructose, appreciable operational stability, excellent durability, and good repeatability (with relative standard deviations of 2.3%). It was successfully applied to the determination of glucose in diluted serum samples. Graphical abstractSchematic representation of electrochemical detection of glucose based on the use of a screen printed carbon electrode (SPCE) modified with CuS and xanthan gum-derived carbon nanofibers (XGCNFs).

Anisotropic Plasmonic CuS Nanocrystals as a Natural Electronic Material with Hyperbolic Optical Dispersion

Copper sulfide nanocrystals have recently been studied due to their metal-like behavior and strong plasmonic response, which make them an attractive material for nanophotonic applications in the near-infrared spectral range; however, the nature of the plasmonic response remains unclear. We have performed a combined experimental and theoretical study of the optical properties of copper sulfide colloidal nanocrystals and show that bulk CuS resembles a heavily doped p-type semiconductor with a very anisotropic energy band structure. As a consequence, CuS nanoparticles possess key properties of relevance to nanophotonics applications: they exhibit anisotropic plasmonic behavior in the infrared and support optical modes with hyperbolic dispersion in the 670-1050 nm spectral range. We also predict that the ohmic loss is low compared to conventional plasmonic materials such as noble metals in the NIR. The plasmonic resonances can be tuned by controlling the size and shape of the nanocrystals, providing a playground for future nanophotonic applications in the near-infrared.

Stable Copper Tin Sulfide Nanoflower Modified Carbon Quantum Dots for Improved Supercapacitors

Copper tin sulfides (CTSs) have widely been investigated as electrode materials for supercapacitors owing to their high theoretical pseudocapacitances. However, the poor intrinsic conductivity and volume change during redox reactions hindered their electrochemical performances and broad applications. In this study, carbon quantum dots (CQDs) were employed to modify CTSs. The structures and morphologies of obtained materials were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). XRD revealed CTSs were composed of Cu2SnS3 and Cu4SnS4, and TEM suggested the decoration of CQDs on the surface of CTSs. With the decoration of CQDs, CTSs@CQDs showed a remarkable specific capacitance of 856 F·g−1 at 2 mV·s−1 and a high rate capability of 474 F·g−1 at 50 mV·s−1, which were superior to those of CTSs (851 F·g−1 at 2 mV·s−1 and 192 F·g−1 at 50 mV·s−1, respectively). This was mainly ascribed to incorporation of carbon quantum dots, which improved the electrical conductivity and alleviated volume change of CTSs during charge/discharge processes.

A cabbage leaf like nanostructure of a NiS@ZnS composite on Ni foam with excellent electrochemical performance for supercapacitors

In the present study, a NiS@ZnS composite nanostructure was synthesized on a nickel foam substrate by a facile chemical bath deposition (CBD) method.

Wrapping CuCo2S4 arrays on nickel foam with Ni2(CO3)(OH)2 nanosheets as a high-performance faradaic electrode

Ternary metal sulfides represent a new class of faradaic electrode material outperforming their oxide counterparts.

One-pot synthesis of ZnS nanowires/Cu7S4 nanoparticles/reduced graphene oxide nanocomposites for supercapacitor and photocatalysis applications

ZnS nanowires/Cu₇S₄ nanoparticles/rGO nanocomposites were fabricated as photocatalysts and supercapacitor electrodes for the first time.

Electrodeposited Ni(OH)2-modified CuS core–shell-like hybrids as binder-free electrodes for high-performance supercapacitors

In this work, binder-free electrodes of CuS@Ni(OH)₂ were fabricated by hydrothermal and electrodeposition methods.

3D hierarchical porous CuS flower-dispersed CNT arrays on nickel foam as a binder-free electrode for supercapacitors

To fabricate excellent electrochemical supercapacitors, 3D porous copper sulfide flower dispersed carbon nanotube on nickel foam (CuS–CNTs@NF) with high energy density and stability were synthesized via a simple one-step solvothermal method.

Selective Growth Synthesis of Ternary Janus Nanoparticles for Imaging-Guided Synergistic Chemo- and Photothermal Therapy in the Second NIR Window

Multifunctional therapeutic agents in the second near-infrared (NIR-II) window have attracted wide attention on account of their synergetic properties for effective cancer therapy. Here, we construct a selective growth strategy for the first time to fabricate ternary Janus nanoparticles (JNPs) containing hemispherical MnO₂ at one side and Au core covered with CuS shell at opposite side. The obtained ternary JNPs are further modified with poly(ethylene glycol)thiol to enhance the stability and biocompatibility (designated as PEG-CuS-Au-MnO₂ ternary JNPs). The MnO₂ domain with mesoporous structures can serve as hydrophobic drug carriers and magnetic resonance (MR) imaging contrast agents. Meanwhile, the Au segment is used for X-ray computed tomography (CT) imaging. Moreover, the PEG-CuS-Au-MnO₂ ternary JNPs can conduct hyperthermia at 1064 nm in NIR-II window to ablate tumors in deep tissue, which is ascribed to the localized surface plasmon resonance coupling effect of the Au core and CuS domain. All of the results reveal that PEG-CuS-Au-MnO₂ ternary JNPs not only exhibit pre-eminent CT/MR imaging capabilities, but also provide high chemo-photothermal antitumor efficacy under the guidance of CT/MR imaging. Taking together, the PEG-CuS-Au-MnO₂ ternary JNPs can be regarded as a prospective therapeutic nanoplatform for dual-modal imaging-guided synergistic chemo-photothermal cancer therapy in the NIR-II window.

New metal-free catalytic degradation systems with carbon dots for thymol blue

A metal-free catalytic system with carbon dots as a catalyst for thymol blue degradation in slightly alkaline aqueous media.