Supramolecular-Based Regenerable Coating Layer of a Thin-Film Composite Nanofiltration Membrane for Simultaneously Enhanced Desalination and Antifouling Properties

Nanofiltration Membranes Containing a Metal-Polyphenol Network Layer: Using Casting Solution pH as a Tool to Tailor the Separation Performance

Thin-film composite (TFC) membranes containing metal-polyphenol network (MPN) selective layers were fabricated using a supramolecular self-assembly between tannic acid (TA) and ferric ion (Fe3+). The TA-Fe3+ thin film was coated on a porous polyacrylonitrile support using aqueous solutions of TA and FeCl3 via a layer-by-layer deposition technique. The pH of the TA solution was used as a tool to alter the membrane characteristics. The surface porosity and water contact angle of the fabricated membranes gradually decreased as the pH of TA casting solutions was increased from 3 to 8.5 for both single-layered and double-layered TA-Fe3+ TFC membranes. This allowed us to tune the water permeance and the retentions of water-soluble neutral and anionic molecules by the MPN membranes by varying the pH of the casting solution. It has been shown that the water permeance decreased from 184 to 156 L·m-2·h-1·bar-1 for single TA-Fe3+ layer coated membranes when the pH was increased from 3 to 8.5, while it declined from 51 to 17 for the double TA-Fe3+ layer. Anionic solutes in aqueous solutions were highly retained compared to neutral components as the TFC membranes had a negative surface charge. Retentions of 95 and 90% were achieved for naphthol green B and orange II dyes by a double-layered M4 membrane fabricated at pH 8.5, while only 13% retention was found for the neutral riboflavin. The neutral dye riboflavin permeated 30.8 times higher than the anionic dye naphthol green B during a mixed dye filtration test through the TFC membrane prepared by using a TA solution of pH 8.5. To the best of our knowledge, this is the highest selectivity of a neutral/anionic dye pair so far reported for a TFC membrane having an MPN selective layer. Moreover, fouling tests have demonstrated that the MPN separation layers exhibit robust stability and adequate antifouling performance with a flux recovery ratio as high as 82%.

High-Performance Nanofiltration Membrane with Dual Resistance to Gypsum Scaling and Biofouling for Enhanced Water Purification

Nanofiltration (NF) technology is pivotal for ensuring a sustainable and reliable supply of clean water. To address the critical need for advanced thin-film composite (TFC) polyamide (PA) membranes with exceptional permselectivity and fouling resistance for emerging contaminant purification, we introduce a novel high-performance NF membrane. This membrane features a selective polypiperazine (PIP) layer functionalized with amino-containing quaternary ammonium compounds (QACs) through an in situ interfacial polycondensation reaction. Our investigation demonstrated that precise QAC functionalization enabled the construction of the selective PA layer with increased surface area, enhanced microporosity, stronger electronegativity, and reduced thickness compared to the control PIP membrane. As a result, the QAC NF membrane exhibited an approximately 51% increase in water permeance compared to the control PIP membrane, while achieving superior retention capabilities for divalent salts (>99%) and emerging organic contaminants (>90%). Furthermore, the incorporation of QACs into the PIP selective layer was proved to be effective in mitigating mineral scaling by allowing selective passage of scale-forming cations, while simultaneously exhibiting strong antimicrobial properties to combat biofouling. The in situ QAC incorporation strategy presented in this study provides valuable guidelines for the fit-for-purpose design of the selective PA layer, which is crucial for the development of high-performance NF membranes for efficient water purification.

Biomimetic nanoporous oxygenation membranes with high hemocompatibility and fast gas transport property

Membrane technology holds great potential for separation applications and also finds critical needs in biomedical fields, such as blood oxygenation. However, the bottlenecks in gas permeation, plasma leakage, and especially hemocompatibility hamper the development of membrane oxygenation. It remains extremely challenging to design efficient membranes and elucidate underlying principles. In this study, we report biomimetic decoration of asymmetric nanoporous membranes by ultrathin FeIII-tannic acid metal-ligand networks to realize fast gas exchange with on plasma leakage and substantially enhance hemocompatibility. Because the intrinsic nanopores facilitate gas permeability and the FeIII-catechol layers enable superior hydrophilicity and electronegativity to original surfaces, the modified membranes exhibit high transport properties for gases and great resistances to protein adsorption, platelet activation, coagulation, thrombosis, and hemolysis. Molecular docking and density functional theory simulations indicate that more preferential adsorption of metal-ligand networks with water molecules than proteins is critical to anticoagulation. Moreover, benefiting from the better antiaging property gave by biomimetic decoration, the membranes after four-month aging present gas permeances similar to or even larger than those of pristine ones, despite the initial permeation decline. Importantly, for blood oxygenation, the designed membranes after aging show fast O2 and CO2 exchange processes with rates up to 28-17 and 97-47 mL m-2 min-1, respectively, accompanied with no detectable thrombus and plasma leakage. We envisage that the biomimetic decoration of nanoporous membranes provide a feasible route to achieve great biocompatibility and transport capability for various applications.

Polyphenol-mediated defect patching of graphene oxide membranes for sulfonamide contaminants removal and fouling control

Graphene oxide (GO)-based laminar membranes are promising candidates for next-generation nanofiltration membranes because of their theoretically frictionless nanochannels. However, nonuniform stacking during the filtration process and the inherent swelling of GO nanosheets generate horizontal and vertical defects, leading to a low selectivity and susceptibility to pore blockage. Herein, both types of defects are simultaneously patching by utilizing tannic acid and FeⅢ. Tannic acid first partially reduced the upper GO framework, and then coordinated with FeⅢ to form a metal-polyphenol network covering horizontal defects. Due to the enhanced steric hindrance, the resulting membrane exhibited a two-fold increase in sulfonamide contaminants exclusion compared to the pristine GO membrane. A non-significant reduction in permeance was observed. In terms of fouling control, shielding defects significantly alleviated the irreversible pore blockage of the membrane. Additionally, the hydrophilic metal-polyphenol network weakened the adhesion force between the membrane and foulants, thereby improving the reversibility of fouling in the cleaning stage. This work opens up a new way to develop GO-based membranes with enhanced separation performance and antifouling ability.

Surface modification of FeⅢ-juglone coating on nanofiltration membranes for efficient biofouling mitigation

Nanofiltration membranes have increasingly played a vital role in the purification of surface water and the recycling of wastewater. However, the problem of membrane biofouling, which leads to shortened service life and increased energy consumption, has hindered the widespread application of nanofiltration membranes. In this study, we developed functionalized nanofiltration membranes with anti-adhesive and anti-biofouling properties by coordinating FeIII and juglone onto commercial nanofiltration membranes in a facile and viable manner. Due to the hydrophilic nature of the FeⅢ-juglone coating as well as its ultra-thin thickness and minimal impact on the membrane pores, the permeance of the optimally modified membrane even increased slightly (14 %). The outstanding anti-adhesive property of the FeⅢ-juglone coating was demonstrated by a significant reduction in the adsorption of proteins and bacteria. Furthermore, the modified membranes exhibited lower flux decline amplitude and reduced biofilm deposition during dynamic fouling experiment, further supporting the outstanding anti-biofouling performance of the nanofiltration membrane after the modification with FeⅢ-juglone coating. This study presents a novel and feasible approach for simultaneously improving the water permeance, anti-adhesive property and anti-biofouling property of commercial nanofiltration membranes.

Development of Support Layers and Their Impact on the Performance of Thin Film Composite Membranes (TFC) for Water Treatment

Thin-film composite (TFC) membranes have gained significant attention as an appealing membrane technology due to their reversible fouling and potential cost-effectiveness. Previous studies have predominantly focused on improving the selective layers to enhance membrane performance. However, the importance of improving the support layers has been increasingly recognized. Therefore, in this review, preparation methods for the support layer, including the traditional phase inversion method and the electrospinning (ES) method, as well as the construction methods for the support layer with a polyamide (PA) layer, are analyzed. Furthermore, the effect of the support layers on the performance of the TFC membrane is presented. This review aims to encourage the exploration of suitable support membranes to enhance the performance of TFC membranes and extend their future applications.

Separation Performance of Membranes Containing Ultrathin Surface Coating of Metal-Polyphenol Network

Metal-polyphenol networks (MPNs) are being used as versatile coatings for regulating membrane surface chemistry and for the formation of thin separation layers. The intrinsic nature of plant polyphenols and their coordination with transition metal ions provide a green synthesis procedure of thin films, which enhance membrane hydrophilicity and fouling resistance. MPNs have been used to fabricate tailorable coating layers for high-performance membranes desirable for a wide range of applications. Here, we present the recent progress of the use of MPNs in membrane materials and processes with a special focus on the important roles of tannic acid-metal ion (TA-Mⁿ⁺) coordination for thin film formation. This review introduces the most recent advances in the fabrication techniques and the application areas of TA-Mⁿ⁺ containing membranes. In addition, this paper outlines the latest research progress of the TA-metal ion containing membranes and summarizes the role of MPNs in membrane performance. The impact of fabrication parameters, as well as the stability of the synthesized films, is discussed. Finally, the remaining challenges that the field still faces and potential future opportunities are illustrated.

Roles and gains of coordination chemistry in nanofiltration membrane: A review

The nanofiltration (NF) membranes with the specific separation accuracy for molecules with the size of 0.5-2 nm have been applied in various industries. However, the traditional polymeric NF membranes still face problems like the trade-off effect, organic solvent consumption, and weak durability in harsh conditions. The participation of coordination action or metal-organic coordination compounds (MOCs) brings the membrane with uniform pores, better antifouling properties, and high hydrophilicity. Some of the aqueous-phase reactions also help to introduce a green fabrication process to NF membranes. This review critically summarizes the recent research progress in coordination chemistry relevant NF membranes. The participation of coordination chemistry was classified by the various functions in NF membranes like additives, interlayers, selective layers, coating layers, and cross-linkers. Then, the effect and mechanism of the coordination chemistry on the performance of NF membranes are discussed in depth. Perspectives are given for the further promotion that coordination chemistry can make in NF processes. This review also provides comprehensive insight and constructive guidance on high-performance NF membranes with coordination chemistry.

A Novel Approach for the Development of Low-Cost Polymeric Thin-Film Nanocomposite Membranes for the Biomacromolecule Separation

The separation of biomacromolecules, mainly proteins, plays a significant role in the pharmaceutical and food industries. Among the membranes' techniques, thin-film nanocomposite nanofiltration membranes are the best choice due to their high energy efficiency, excellent productivity, cost-effective and tuneable properties that have captured the attention of the efficient separation of biomacromolecules, especially from the industrial perspective. The present work directs the efficient separation study of proteins, namely, lysozyme, trypsin, pepsin, bovine serum albumin (BSA), and cephalexin, using a thin-film nanocomposite membrane integrated with Arg-MMT (arginine-montmorillonite) clay nanoparticles. The surface morphology and cross-section images of the TFN membranes were studied using a field emission scanning electron microscope (FE-SEM) and a high-resolution transmission electron microscope (HR-TEM). The thermal stability and hydrophilicity of the membranes were examined using thermogravimetric analysis (TGA) and contact angle, respectively. The surface chemistry of the selective layer has different functional groups that were analyzed using FTIR spectroscopy. The performance of the membranes was studied at different trans-membrane pressures and permeation times. The effect of monomer concentration on the separation performance of the membranes was also studied at different permeation times. The membranes' antibacterial activity was evaluated using the Muller-Hinton disk diffusion method using gram-negative Escherichia coli (E. coli) and gram-positive Staphylococcus aureus (S. aureus) bacteria. The highest rejection was achieved for BSA up to 98.92 ± 1%, and the highest permeation was obtained against lysozyme feed solution up to 26 L m^-2 h^-1 at 5 bar pressure. The membrane also illustrated excellent rejection of cephalexin antibiotics with a rejection of 98.17 ± 1.75% and a permeation flux of 26.14 L m^-2 h^-1. The antifouling study performed for the membranes exhibited a flux recovery ratio of 86.48%. The fabricated thin-film nanocomposite membrane demonstrated a good alternative for the separation of biomacromolecules and has the potential to be used in different sectors of industry, especially the pharmaceutical and food industry.

Loosely Sandwich-Structured Membranes Decorated with UiO-66-NH2 for Efficient Antibiotic Separation and Organic Solvent Resistance

Thin-film nanocomposite (TFN) membranes with efficient molecular separation and organic solvent resistance are active in demand in wastewater treatment and resource reclamation, meeting the goal of emission peaks and carbon neutrality. In this work, a simple and rational design strategy has been employed to construct a sandwich-structured membrane for removing fluoroquinolone antibiotics and recycling organic solvents. The sandwich-structured membrane is composed of a porous substrate, a hydrophilic tannic acid-polyethyleneimine (TA-PEI) interlayer, and a polyamide (PA) selective layer decorated with metal-organic framework (PA-MOF). Results manifest that the hydrophilic TA-PEI interlayer played a bridging and gutter effect to achieve effective control in amide storage, amine diffusion, and nanomaterial downward leakage at the immiscible interface. The PA-MOF selective layer has been changed to a loosely crumpled surface, endowing functionalities on the sandwich-structured membrane that included limited pores, strengthened electronegativity, and stronger hydrophilicity. Thus, an enhanced water flux of 87.23 ± 7.43 LMH was achieved by the TFN-2 membrane (0.04 mg·mL^-1 UiO-66-NH₂), which is more than five times that of the thin-film composite membrane (17.46 ± 3.88 LMH). The rejection against norfloxacin, ciprofloxacin, and levofloxacin is 92.94 ± 1.60%, 94.62 ± 1.29%, and 96.92 ± 1.05%, respectively, effectively breaking through the "trade-off" effect between membrane permeability and rejection efficiency. Further antifouling results showed that the sandwich-structured membrane had lower flux decay ratios (3.36∼7.07%) and higher flux recovery ratios (93.40∼98.40%), as well as superior long-term stability after 30 days of filtration. Moreover, organic solvent resistance testing confirms that the sandwich-structured membrane maintained stable solvent flux and better recovery rates in ethanol, acetone, isopropanol, and N,N-dimethylformamide. Detailed nanofiltration mechanism studies revealed that these outstanding performances are based on the joint effect of the TA-PEI interlayer and PA-MOF selective layer, proposing a new perspective to break through the bottleneck of nanofiltration application in a complex environment.

Polymeric Membrane Marine Sensors with a Regenerable Antibiofouling Coating Based on Surface Modification of a Dual-Functionalized Magnetic Composite

Environmentally compatible polymeric membrane marine sensors with excellent antiadhesive and antibacterial properties have recently been developed. However, the regeneration abilities of these sensors after fouling have rarely been investigated. Herein, a novel strategy for preparation of a regenerable antibiofouling coating via surface modification of a dual-functionalized magnetic composite is proposed. A zwitterionic polymer (i.e., poly(sulfobetaine methacrylate)) and a quaternary ammonium compound (i.e., 3-trimethoxysilylpropyl octadecyldimethyl ammonium chloride) are coated on the surface of Fe₃O₄ microspheres for antiadhesion and bacterial inactivation, respectively. The antifouling magnetic composite can readily be modified on the sensor's surface via the magnetically assisted self-assembly technology. Using a polymeric membrane calcium ion-selective electrode as a model sensor, the protection layer-coated electrode shows the markedly improved antibiofouling activities as compared to the unmodified sensor. More importantly, by altering the direction of the external magnetic field, the antifouling coating can easily be removed after fouling along with the removal of the adsorbed bacterial cells from the electrode's surface, which is followed by re-modifying a fresh coating for regeneration of the antifouling electrode. The proposed methodology for fabrication of a regenerable antibiofouling coating is promising to improve the durability of a marine sensor.

Enhancing the Antifouling Ability of a Polyamide Nanofiltration Membrane by Narrowing the Pore Size Distribution via One-Step Multiple Interfacial Polymerization

Application of nanofiltration membranes in industries still has to contend with membrane fouling that causes a significant loss of separation performance. Herein, an innovative approach to design antifouling membranes with a narrowed pore size distribution by interfacial polymerization (IP) assisted by silane coupling agents is reported. An aqueous solution of piperazine anhydrous (PIP) and γ-(2,3-epoxypropoxy) propytrimethoxysilane (KH560) is employed to perform IP with an organic solution of trimesoyl chloride and tetraethyl orthosilicate (TEOS) on a porous support. In accordance with the results of molecular dynamics and dissipative particle dynamics simulations, the reactive additive KH560 accelerates the diffusion rate of PIP to enrich at the reaction boundary. Moreover, the hydrolysis/condensation of KH560 and TEOS at the aqueous/organic interface forms an interpenetrating network with the polyamide network, which regulates the separation layer structure. The characterization results indicate that the polyamide-silica membrane has a denser, thicker, and uniform separation layer. The mean pore size of the polyamide-silica membrane and the traditional polyamide membrane is 0.62 and 0.74 nm, respectively, and these correspond to the geometric standard deviation (namely, pore size distribution) of 1.39 and 1.97, respectively. It is proved that the narrower pore size distribution endows the polyamide-silica membrane with stronger antifouling performance (flux decay ratio decreases from 18.4 to 3.8%). Such a membrane also has impressive long-term antifouling stability during cane molasses decolorization at a high temperature (50 °C). The outcomes of this study not only provide a novel one-step multiple IP strategy to prepare antifouling nanofiltration membranes but also emphasize the importance of pore size distribution in fouling control for various industrial liquid separations.

A sacrificial protective layer as fouling control strategy for nanofiltration in water treatment

High-performance nanofiltration (NF) membrane with super antifouling capability as well as reusability is highly desired in water treatment. A new antifouling strategy by a coating-decoating-recoating cycle was investigated for effective removal of fouling and restoring the original membrane performance. The functional membrane surface was fabricated by in-situ coating a 'green' and biodegradable carboxymethyl chitosan (CMCS) layer as physical barrier. The CMCS layer can be decoated and re-coated by simple procedures. Results showed that (i) the CMCS layer enhanced surface hydrophilicity, surface smoothness and fouling resistance of NF membrane, (ii) both the unfouled and fouled CMCS layer were easily decoated by the strong acid solution, (iii) the CMCS layer was easily re-coated by facile recoating and (iv) the water flux recovery ratio of membrane with coating layer was maintained more than 88.8% during fouling testing by natural organic matter (NOM) after four sequential cycles of coating, decoating and recoating process. The re-coated membrane exhibited stable, improved membrane operational and antifouling performance. The coating-decoating-recoating approach is proven to be low-cost and eco-friendly strategy for NOM fouling control on NF membrane in water treatment applications.

Enhancing the Permselectivity of Thin-Film Composite Membranes Interlayered with MoS2 Nanosheets via Precise Thickness Control

The demand for highly permeable and selective thin-film composite (TFC) nanofiltration membranes, which are essential for seawater and brackish water softening and resource recovery, is growing rapidly. However, improving and tuning membrane permeability and selectivity simultaneously remain highly challenging owing to the lack of thickness control in polyamide films. In this study, we fabricated a high-performance interlayered TFC membrane through classical interfacial polymerization on a MoS₂-coated polyethersulfone substrate. Due to the enhanced confinement effect on the interface degassing and the improved adsorption of the amine monomer by the MoS₂ interlayer, the MoS₂-interlayered TFC membrane exhibited enhanced roughness and crosslinking. Compared to the control TFC membrane, MoS₂-interlayered TFC membranes have a thinner polyamide layer, with thickness ranging from 60 to 85 nm, which can be tuned by altering the MoS₂ interlayer thickness. A multilayer permeation model was developed to delineate and analyze the transport resistance and permeability of the MoS₂ interlayer and polyamide film through the regression of experimental data. The optimized MoS₂-interlayered TFC membrane (0.3-inter) had a 96.8% Na₂SO₄ rejection combined with an excellent permeability of 15.9 L m^-2 h^-1 bar^-1 (LMH/bar), approximately 2.4 times that of the control membrane (6.6 LMH/bar). This research provides a feasible strategy for the rational design of tunable, high-performance NF membranes for environmental applications.

Removal of chloride from water and wastewater: Removal mechanisms and recent trends

Increased chloride concentration can cause salinization, which has become a serious and widespread environmental problem nowadays. This review aims at providing comprehensive and state-of-the-art knowledge and insights of technologies for chloride removal. Mechanisms for chloride removal mainly include chemical precipitation, adsorption, oxidation and membrane separation. In chemical precipitation, chloride removal by forming CuCl, AgCl, BiOCl and Friedel's salt. Adsorbents used in chloride removal mainly include ion exchangers, bimetal oxides and carbon-based electrodes. Oxidation for chloride removal contains ozone-based, electrochemical and sulfate radical-based oxidation. Membrane separation for chloride removal consists of diffusion dialysis, nanofiltration, reverse osmosis and electrodialysis. In this review, we specifically proposed the factors that affect chloride removal process and the corresponding strategies for improving removal efficiency. In the last section, the remaining challenges of method explorations and material developments were stated to provide guidelines for future development of chloride removal technologies.

A novel ceramic-based thin-film composite nanofiltration membrane with enhanced performance and regeneration potential

The rational design of a ceramic-based nanofiltration membrane remains a significant challenge due to its performance and fabrication cost. Herein, we report a high-performance ceramic-based thin-film composite (TFC) membrane fabricated via a typical interfacial polymerization on an interwoven net substrate assembled by titanium dioxide (TiO₂) nanowires. The chemical properties and morphologies were systematically investigated for ceramic substrates and their corresponding TFC membranes. Due to the significantly improved hydrophilicity of the TiO₂ framework, more reactive amine monomers were uniformly adsorbed on the modified surface of the ceramic substrate, yielding an ultrathin polyamide layer with less resistance. In addition, the smooth surface and decreased pore size of the TiO₂ framework contributed to forming a defect-free polyamide layer. As a result, the obtained ceramic-based TFC membrane evinced high permeance of 26.4 L m^-2 h^-1 bar^-1 and excellent salt rejection efficiency, leading to simultaneous improvements compared with the control TFC membrane without the TiO₂ framework. Notably, the potential regeneration ability of the ceramic-based TFC membrane could be achieved via facile low-temperature calcination and re-polymerization process due to the varied thermostability between the polyamide layer and the robust ceramic substrate. The operation of regeneration helped to prolong the lifetime and decrease the cost for the ceramic-based TFC membrane. This research provides a feasible protocol to fabricate sustainable ceramic-based nanofiltration membranes with enhanced performance for water treatment.

Ultrathin Membranes for Separations: A New Era Driven by Advanced Nanotechnology

Ultrathin membranes are at the forefront of membrane research, offering great opportunities in revolutionizing separations with ultrafast transport. Driven by advanced nanomaterials and manufacturing technology, tremendous progresses are made over the last 15 years in the fabrications and applications of sub-50 nm membranes. Here, an overview of state-of-the-art ultrathin membranes is first introduced, followed by a summary of the fabrication techniques with an emphasis on how to realize such extremely low thickness. Then, different types of ultrathin membranes, categorized based on their structures, that is, network, laminar, or framework structures, are discussed with a focus on the interplays among structure, fabrication methods, and separation performances. Recent research and development trends are highlighted. Meanwhile, the performances and applications of current ultrathin membranes for representative separations (gas separation and liquid separation) are thoroughly analyzed and compared. Last, the challenges in material design, structure construction, and coordination are given, in order to fully realize the potential of ultrathin membranes and facilitate the translation from scientific achievements to industrial productions.

Mechanistic Insights of a Thermoresponsive Interface for Fouling Control of Thin-Film Composite Nanofiltration Membranes

In spite of extensive research, fouling is still the main challenge for nanofiltration membranes, generating an extra transport resistance and requiring a larger operational pressure in practical applications. We fabricated a highly antifouling nanofiltration membrane by grafting poly(N-isopropylacrylamide) (PNIPAM) chains on a bromine-containing polyamide layer. The resulting membrane was found to have a double permeance compared to the pristine membrane, while the rejection of multivalent ions remained the same. In addition, PNIPAM chains yielded a better deposition resistance and adhesion resistance, thereby mitigating the increase of fouling and promoting the recovery of flux during the filtration and traditional cleaning stages, respectively. Moreover, PNIPAM chains shrank when the water temperature was above the lower critical solution temperature (LCST), indicating the formation of a buffer layer between the membrane and pollutants. The buffer layer would eliminate the membrane-foulant interaction energy, thus further enhancing the detachment of pollutants. This simple and efficient cleaning method could act as an enhanced cleaning procedure to remove irreversible fouling. This provides new insights into the fabrication of enhanced antifouling membranes using smart responsive polymer chains.

Toward Enhancing Desalination and Heavy Metal Removal of TFC Nanofiltration Membranes: A Cost-Effective Interface Temperature-Regulated Interfacial Polymerization

Polyamide (PA) chemistry-based nanofiltration (NF) membranes have an important role in the field of seawater desalination and wastewater reclamation. Achieving an ultrathin and defect-free active layer via precisely controlled interfacial polymerization (IP) is an effective routine to improve the separation efficiencies of NF membranes. Herein, the morphologies and chemical structures of the thin-film composite (TFC) NF membranes were accurately regulated by tailoring the interfacial reaction temperature during the IP process. This strategy was achieved by controlling the temperature (-15, 5, 20, 35, and 50°) of the oil-phase solutions. The structural compositions, morphological variations, and separation features of the fabricated NF membranes were studied in detail. In addition, the formation mechanisms of the NF membranes featuring different PAs were also proposed and discussed. The temperature-assisted IP (TAIP) method greatly changed the compositions of the resultant PA membranes. A very smooth and thin PA film was obtained for the NF membranes fabricated at a low interfacial temperature; thus, a high 19.2 L m^-2 h^-1 bar^-1 of water permeance and 97.7% of Na₂SO₄ rejection were observed. With regard to the NF membranes obtained at a high interfacial temperature, a lower water permeance and higher salt rejection with fewer membrane defects were achieved. Impressively, the high interfacial temperature-assisted NF membranes exhibited uniform coffee-ring-like surface morphologies. The special surface-featured NF membrane showed superior separation for selected heavy metals. Rejections of 93.9%, 97.9%, and 87.7% for Cu²⁺, Mn²⁺, and Cd²⁺ were observed with the optimized membrane. Three cycles of fouling tests indicated that NF membranes fabricated at low temperatures exhibited excellent antifouling behavior, whereas a high interface temperature contributed to the formation of NF membranes with high fouling tendency. This study provides an economical, facile, and universal TAIP strategy for tailoring the performances of TFC PA membranes for environmental water treatment.

Facile Surface Modification of Polyamide Membranes Using UV-Photooxidation Improves Permeability and Reduces Natural Organic Matter Fouling

A new optimized ultraviolet (UV) technique induced a photooxidation surface modification on thin-film composite (TFC) polyamide (PA) brackish water reverse osmosis (BWRO) membranes that improved membrane performance (i.e., permeability and organic fouling propensity). Commercial PA membranes were irradiated with UV-B light (285 nm), and the changes in the membrane performance were assessed through dead-end and cross-flow tests. UV-B irradiation at 12 J·cm^-2 enhanced the pure water permeability by 34% in the dead-end tests without decreasing the mono- or divalent ion rejections, as compared with the pristine PA membrane, and led to less fouling by natural organic matter in the cross-flow tests. Scanning electron microscopy (SEM), attenuated total reflection Fourier transform infrared (ATR-FTIR) spectroscopy, and X-ray photoelectron spectroscopy (XPS) confirmed that UV-B irradiation opened the pore structure and created carboxylic and amine groups on the PA surface, leading to increased membrane surface charge and hydrophilicity. Thus, an optimal UV-B dose appears to modify only a thin layer of the PA membrane surface, which favorably enhances the membrane performance. UV-B did not alter the structure, flux, or salt rejection for cellulose triacetate (CTA)-based membranes. While other membrane surface modifications include oxidants, strong acids, and bases, the UV-B facile treatment is chemical-free, thus reducing chemical wastes, and easy to apply in roll-to-roll fabrication processes of PA membranes. The results also showed that a low UV irradiation dose could be applied to PA or CTA membranes for disinfection or photocatalytic oxidation.

Enhanced Water Permeability and Antifouling Property of Coffee-Ring-Textured Polyamide Membranes by In Situ Incorporation of a Zwitterionic Metal-Organic Framework

Modulation of the polyamide structure is critically important for the reverse-osmosis performance of thin-film composite (TFC) membranes in the field of water reuse and desalination. Herein, zwitterionic nanoparticles of zeolitic imidazolate framework-8 (PZ@ZIF-8) were fabricated and incorporated into the polyamide active layer through the interfacial polymerization method. A hydrophilic, zwitterionic coffee-ring structure was formed on the surface of polyamide thin-film nanocomposite (TFN) membranes due to the adjusted diffusion rate of m-phenylenediamine (MPD) from the aqueous phase into the organic phase during the interfacial polymerization process. Surface characterization demonstrated that the coffee-ring structure increased the amounts of water transport channels on the membrane surface and the intrinsic pores of PZ@ZIF-8 maintained the salt rejection. Antifouling and bactericidal activities of TFN membranes were enhanced remarkably owing to the bacterial-"defending" and bacterial-"attacking" behaviors of hydrophilic and zwitterionic groups from PZ@ZIF-8 nanoparticles. This work would provide a promising method for the application of MOFs to enhance the bio-/organic-fouling resistance of TFN membranes with high water permeation and salt rejection.

MXene Nanosheet Templated Nanofiltration Membranes toward Ultrahigh Water Transport

The demand for thin-film composite (TFC) nanofiltration membranes with superior permeance and high rejection is gradually increasing for seawater desalination and brackish water softening. However, improving the membrane permeance remains a great challenge due to the formation of excrescent polyamide in the substrate pores and thick polyamide film. Herein, we fabricated a high-performance TFC nanofiltration membrane via a classical interfacial polymerization reaction on a two-dimensional lamellar layer of transition-metal carbides (MXene). The MXene layer promoted the absorption of the reactive monomer, and higher amine monomer concentration facilitated the self-sealing and self-termination of interfacial polymerization to generate a thinner outer polyamide film from 68 to 20 nm. The almost nonporous lamellar interface inhibited the formation of inner polyamide in the substrate pores. In addition, the MXene lamellar layer could be eliminated by mild oxidation after interfacial polymerization to avoid imparted additional hydraulic resistance. The resulting TFC membrane conferred a high rejection above 96% for Na₂SO₄ and excellent permeance of 45.7 L·m^-2·h^-1·bar^-1, which was almost 4.5 times higher than that of the control membrane (10.2 L·m^-2·h^-1·bar^-1). This research provides a feasible strategy for fabricating a high-performance nanofiltration membrane using two-dimensional nanosheets as a templated interface.

Antifouling Nanofiltration Membrane Fabrication via Surface Assembling Light-Responsive and Regenerable Functional Layer

Membrane fouling, caused by aggregation of organics and microorganisms from filtrate on the membrane surface, seriously reduces the service life of a nanofiltration (NF) membrane. Developing facile and renewable antifouling modification methods without sacrificing separation properties of the membrane remain an imperative requirement. Herein, a thin-film composite (TFC) NF membrane with a light-responsive and regenerable functional layer (P-TFC) was fabricated via host-guest interactions between the azobenzene (guest) labeled functional polymers and the β-cyclodextrin (host) bonded membrane surface (H-TFC). The P-TFC-3 not only showed outstanding antifouling ability and high flux recovery ratio (FRR > 90% at the fourth antiadhesive test) but also exhibited enhanced water permeability (17.9 L m^-2 h^-1 bar^-1) and high selectivity (α_MgSO4^NaCl = 33.4 and fast antibiotics enrichment capacity) compared with the pristine membrane. Furthermore, when the functional layer was contaminated, it can be removed by ultraviolet light irradiation and a new functional layer can be rebuilt by adding fresh azobenzene labeled functional polymers. After several regeneration processes, the membranes still showed constant separation properties and high flux recovery ability (FRR > 90%). This work proposes an easy-to-assemble and regenerable surface modification strategy to endow TFC NF membranes with excellent fouling resistance and sustainable utilization ability while maintaining high separation properties.

Ultra-low pressure cellulose-based nanofiltration membrane fabricated on layer-by-layer assembly for efficient sodium chloride removal

Cellulose is a renewable, biodegradable, biocompatible, and sustainable material. A bamboo cellulose-based nanofiltration membrane (LBL-NF-CS/BCM) was prepared with a combination of layer-by-layer assembly and spraying methods. The chemical structure, morphology, and surface charge of the resultant LBL-NF-CS/BCM composite membranes were characterized based on Thermo Gravimetric Analysis (TGA), X-ray diffraction (XRD), Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM), and X-ray Photoelectron Spectroscopy Scanning (XPS). The nanofiltration performance of the LBL-NF-CS/BCM composite membranes was evaluated using 500 ppm NaCl solutions under 0.3 MPa pressure. It was found that the LBL-NF-CS/BCM composite membranes had a rejection rate of about 36.11 % against a 500 ppm NaCl solution under the conditions tested, and membrane flux of about 12.08 L/(m² h) was reached. The combined layer-by-layer assembly and spraying provides a scalable and convenient process concept for nanofiltration membrane fabrication.

Applications of tannic acid in membrane technologies: A review

Today, membrane technologies play a big role in chemical industry, especially in separation engineering. Tannic acid, one of the most famous polyphenols, has attracted widespread interest in membrane society. In the past several years, researches on the applications of tannic acid in membrane technologies have grown rapidly. However, there has been lack of a comprehensive review for now. Here, we summarize the recent developments in this field for the first time. We comb the history of tannic acid and introduce the properties of tannic acid firstly, and then we turn our focus onto the applications of membrane surface modification, interlayers and selective layers construction and mixed matrix membrane development. In those previous works, tannic acid has been demonstrated to be capable of making a great contribution to the membrane science and technology. Especially in membrane surface/interface engineering (such as the construction of superhydrophilic and antifouling surfaces and polymer/nanoparticle interfaces with high compatibility) and development of thin film composite membranes with high permselectivity (such as developing thin film composite membranes with ultrahigh flux and high rejection), tannic acid can play a positive and great role. Despite this, there are still many critical challenges lying ahead. We believe that more exciting progress will be made in addressing these challenges in the future.