Anchoring Black Phosphorus Nanoparticles onto ZnS Porous Nanosheets: Efficient Photocatalyst Design and Charge Carrier Dynamics

Heterogeneous Interface Engineering of 2D Black Phosphorus-Based Materials for Enhanced Photocatalytic Performance

Photocatalysis has garnered significant attention as a sustainable approach for energy conversion and environmental management. 2D black phosphorus (BP) has emerged as a highly promising semiconductor photocatalyst owing to its distinctive properties. However, inherent issues such as rapid recombination of photogenerated electrons and holes severely impede the photocatalytic efficacy of single BP. The construction/stacking mode of BP with other nanomaterials decreases the recombination rate of carriers and extend its functionalities. Herein, from the perspective of atomic interface and electronic interface, the enhancement mechanism of photocatalytic performance by heterogeneous interface engineering is discussed. Based on the intrinsic properties of BP and corresponding photocatalytic principles, the effects of diverse interface characteristics (point, linear, and planar interface) and charge transfer mechanisms (type I, type II, Z-scheme, and S-scheme heterojunctions) on photocatalysis are summarized systematically. The modulation of heterogeneous interfaces and rational regulation of charge transfer mechanisms can enhance charge migration between interfaces and even maximize redox capability. Furthermore, research progress of heterogeneous interface engineering based on BP is summarized and their prospects are looked ahead. It is anticipated that a novel concept would be presented for constructing superior BP-based photocatalysts and designing other 2D photocatalytic materials.

Improved photocatalytic performance of cobalt doped ZnS decorated with graphene nanostructures under ultraviolet and visible light for efficient hydrogen production

Highly dispersed Cobalt doped ZnS nanostructures were successfully fabricated on the surfaces of graphene sheets via a simple hydrothermal method. X-ray diffraction (XRD), X-ray photocurrent spectroscopy (XPS), Raman spectroscopy (RS), Fourier transform infrared spectroscopy (FTIR) and Scanning electron microscopy (SEM) were utilized to analyze the structural characteristics of the cobalt doped ZnS decorated with grapheneCo x Zn 1 - x S rGO nanostructures (NSs). UV-visible optical absorption (UV-vis) studies were conducted to investigate their optical properties. In laboratory studies utilizing water and visible light, the photocatalytic activity ofCo x Zn 1 - x S rGO NSs at (x = 0, 1, 2, 4 and 6 atm.%) were evaluated. Graphite Oxide (GO) was successfully transformed into sheets of graphene andCo x Zn 1 - x S rGO NSs possessed a crystalline structure according to the findings of XRD, RS and FTIR analysis. SEM investigation showed graphene sheets enhanced with ZnS NSs possessed cuboidal, spheroidal form of structure and displayed a paper like appearance. UV-vis confirmed a noticeable rapid increase in transmittance along the UV wavelength area and confirmed a highly transparent NSs in the wavelength range of (180-800 nm). Calculations using density functional theory (DFT) revealed that the Co NSs have more negative conduction bands than ZnS, allowing for effective electron transfer from cobalt to ZnS and exhibiting a band gap decrease as Co content increased. TheCo 0.04 Zn 0.96 S rGO NSs sample had the highest photocatalytic activity, measured at 7648.9 μ mol h - 1 . A combination of improved dispersion properties, greater surface area, increased absorption and enhanced transfer of photogenerated electrons,Co x Zn 1 - x S rGO NSs increased the photocatalytic hydrogen generation activity.

Interfacial tuning in FeP/ZnIn2S4 Ohm heterojunction: Enhanced photocatalytic hydrogen production via Zn-P charge bridging

Interfacial regulation is key to photocatalytic performance, yet modulating interfacial charge transfer in heterostructures remains challenging. Herein, a novel nanoflower-like FeP/ZnIn2S4 Ohm heterostructure is first designed, with Zn atoms in ZnIn2S4 (ZIS) acting as potential anchoring sites around P atoms, forming liganded Zn-P bonds. Combining 1D FeP nanowires and 2D ZIS nanosheets enhances the mobility of photogenerated electrons. The synergistic chain-type "electron pickup" mechanism of the Ohm heterojunction coupled with the Zn-P bond speeds up electron transport at the interface. The Ohm heterojunction initiates an internal electric field, creating a driving force to further transfer photogenerated electrons through the Zn-P rapid electron transport channel to FeP, which acts as a reservoir for active sites to release H2. The optimized FeP/ZIS demonstrates a remarkable H2 evolution rate at 4.36 mmol h-1 g-1, 3.6 times that of pristine ZIS. This work provides novel insights into optimizing photocarrier dynamics via interfacial microenvironment modulation.

Sonochemically synthesized black phosphorus nanoparticles: a promising candidate for piezocatalytic antibacterial activity with enhanced dielectric properties

The drawbacks inherent to traditional antibacterial therapies, coupled with the escalating prevalence of multi-drug resistant (MDR) microorganisms, have prompted the imperative need for novel antibacterial strategies. Accordingly, the emerging field of piezocatalysis in semiconductors harnesses mechanical stress to drive chemical reactions by utilizing piezo-generated free charge carriers, presenting a promising technology. To the best of our knowledge, this study is the first to provide a comprehensive overview of the eradication of pathogenic S. aureus bacteria using few-layer black phosphorus (SCBP) piezo catalyst under mechanical stimuli, along with the exploration of temperature dependent dielectric properties. The synthesis of the piezo catalysts involved a one-step cost-effective sonochemical method, and its structural, morphological, elemental, optical, and overall polarization properties were thoroughly characterized and compared with the traditional method-derived product (TABP). The synthesis-introduced defects, reduced crystalline diameters, modified bandgap (1.76 eV), nanoparticle aggregation, photoluminescence quenching, along with interfacial polarization, synergistically contribute to SCBP's exceptional dielectric response (4.596 × 107 @40 Hz), which in turn enhanced the piezocatalytic activity. When subjected to soft ultrasound stimulation at 15 kHz, the piezo catalyst SCBP demonstrated significant ROS-mediated antibacterial activity, resulting in a ∼94.7% mortality rate within 40 minutes. The impact of this study extends to cost-effective energy storage devices and advances in antibacterial therapy, opening new dimensions in both fields.

Black Phosphorus-Based Conductive Hydrogels Assisted by Electrical Stimulus for Skin Tissue Engineering

Conductive hydrogels have shown great potential in wound healing and skin tissue engineering, owing to their electroactive, mechanical, and chemical properties. However, it still remains as a challenge to incorporate other functions into conductive hydrogels, such as antibacterial ability, controllable drug release, and biodegradability. In this study, a black phosphorus-based conductive hydrogel (HA-DA@BP) is prepared by an amidation reaction coupled with a coordination of Fe3+ -catechol. The hydrogel could be changed from the sol phase to the gel phase under electrical stimulus (ES). The results show that BP could be released under slight acidity, which is cell compatible but could achieve synergistic electrical antibacterial action and promote wound healing. This study proves that BP is a strong candidate for electroactive materials and provides a new insight for the development of BP-based biomedical materials in skin tissue engineering.

Photocatalytic water splitting for hydrogen production with high efficiency monolayer In2Te5: a theoretical study

Employing density functional theory (DFT) calculations, we explore the excellent performance of two-dimensional (2D) semiconductor In2Te5 in photocatalytic water splitting at the theoretical level. The calculated results illustrate that 2D In2Te5 is a direct band gap semiconductor with a moderate band gap value and an ultrahigh optical absorption coefficient in the visible light region. It was found that its conduction band edge is higher than the reduction potential of water (-4.44 eV), which proves that it can split water to produce hydrogen. Furthermore, its excellent hydrogen evolution activity can be tuned under an appropriate biaxial strain. In addition, 2D In2Te5 shows a remarkable photo-generated current, suggesting that electrons and holes can be separated efficiently. Our results offer a superior candidate material for realizing photocatalytic water splitting for hydrogen evolution.

Enlarging the Ni-O Bond Polarizability in a Phosphorene-Hosted Metal-Organic Framework for Boosted Water Oxidation Electrocatalysis

The emerging lattice-oxygen oxidation mechanism (LOM) presents attractive opportunities for breaking the scaling relationship to boost oxygen evolution reaction (OER) with the direct OLattice-*O interaction. However, currently the LOM-triggering rationales are still debated, and a streamlined physicochemical paradigm is extremely desirable for the design of LOM-defined OER catalysts. Herein, a Ni metal-organic framework/black phosphorene (NiMOF/BP) heterostructure is theoretically profiled and constructed as a catalytic platform for the LOM-derived OER studies. It is found that the p-type BP host can enlarge the Ni-O bond polarizability of NiMOF through the Ni-O bond stretching and Ni valence declining synergically. Such an enlarged bond polarizability will in principle alleviate the lattice oxygen confinement to benefit the LOM pathway and OER performance. As a result, the optimized NiMOF/BP catalyst exhibits promising OER performance with a low overpotential of 260 mV at 10 mA cm-2 and long-term stability in 1 M KOH electrolyte. Both experiment and calculation results suggest the activated LOM pathway with a more balanced step barrier in the NiMOF/BP OER catalyst. This research puts forward Ni-O bond polarizability as the criterion to design LOM-scaled electrocatalysts for water oxidation.

A Portable Wireless Intelligent Nanosensor for 6,7-Dihydroxycoumarin Analysis with A Black Phosphorene and Nano-Diamond Nanocomposite-Modified Electrode

In this work, a novel portable and wireless intelligent electrochemical nanosensor was developed for the detection of 6,7-dihydroxycoumarin (6,7-DHC) using a modified screen-printed electrode (SPE). Black phosphorene (BP) nanosheets were prepared via exfoliation of black phosphorus nanoplates. The BP nanosheets were then mixed with nano-diamond (ND) to prepare ND@BP nanocomposites using the self-assembly method, achieving high environmental stability. The nanocomposite was characterized by SEM, TEM, Raman, XPS and XRD. The nanocomposite was used for the modification of SPE to improve its electrochemical performances. The nanosensor displayed a wide linear range of 0.01-450.0 μmol/L with a low detection limit of 0.003 μmol/L for 6,7-DHC analysis. The portable and wireless intelligent electrochemical nanosensor was applied to detect 6,7-DHC in real drug samples by the standard addition method with satisfactory recoveries, which extends the application of BP-based nanocomposite for electroanalysis.

Production of high-quality and large lateral-size black phosphorus nanoparticles/nanosheets by liquid-phase exfoliation

The liquid phase exfoliation (LPE) of layered black phosphorus (BP) material is essential in the field of electronics. N-Methyl-2-pyrrolidone (NMP) is one of the most promising precursors for obtaining BP nanosheets/nanoparticles, but the longer sonication time leads to smaller production of phosphorene. Herein, for the first time, the large lateral size fabrication of phosphorene was attained through NMP solvent by optimizing the process parameters. The resultant dispersions were characterized by atomic force microscopy, X-ray powder diffraction, Raman spectroscopy, scanning electron microscopy, transmission electron microscopy, and ultraviolet-visible spectroscopy. The characterization results revealed that the average lateral sizes of BP nanoparticles were found to be 67.8 ± 18.6 nm and the lateral size of fabricated BP nanosheets was found to be 5.37 μm. Moreover, this research provides a strategic approach for the mass production of phosphorene for photodetection applications.

Progress in the preparation, application, and recycling of black phosphorus

Black phosphorus nanosheets (BPNSs) are a new member of the nanomaterial family, and they have good development potential in electrochemistry, electronics, optoelectronics, environmental protection, biomedical, and other fields because of their bandgap width, high anisotropy, broad optical absorption, high carrier mobility and many other features. Although many articles have been published about the preparation and application of BPNSs, these aspects have not been elucidated, and we aimed to fill this knowledge gap in this review. First, we used VOSviewer software to sort out articles published in the past 5 years and drew a literature map, which allowed us to sort out the relationship between various studies related to BPNSs, and reflect on the research focus in recent years. Because BPNSs must be made from black phosphorus (BP), and BPNSs are a nano form of BP, the collation of the BP preparation scheme was also helpful for the related research on BPNSs. This paper introduces the preparation of bulk BP and BPNSs, analyzes and compares the advantages and disadvantages of each method, and points out the most promising methods in the future. Then, we propose improvement directions for this method. We also introduce the characterization of BPNSs and combine it with the subsequent photocatalytic application of BPNSs. As a new material, the effect of BPNSs on the environment is still unknown; thus, an end treatment scheme for BPNSs is summarized according to existing methods. Based on the experience of nanomaterial treatment, this paper proposes a research focus for the end treatment of BPNSs in the future, providing a reference scheme for the end treatment of other nanomaterials. Finally, we summarize the full text and propose recommended methods and improvement plans.

Construction of Direct Z-Scheme SnS2 Quantum Dots/Conjugated Polyimide with Superior Photocarrier Separation for Enhanced Photocatalytic Performances

In this study, a novel direct Z-scheme SnS₂ quantum dots/sulfur-doped polyimide (SQDs/SPI) photocatalyst was firstly fabricated by an in situ crystallization growth of SnS₂ quantum dots on sulfur-doped polyimide through a facile hydrothermal method. The photocatalytic hydrogen production activity of 5SQDs/SPI samples reached 3526 μmoL g^-1 in the coexistence of triethanolamine and methanol used as hole sacrificial agents, which is about 13 times higher than that of SPI under the same conditions and 42 times higher than that of SPI only as a hole sacrificial agent. The improvement can be related to the direct Z-scheme charge transfer in the tight interface between SQDs and SPI, which promoted rapid separation and significantly prolonged the lifetime of photoexcited carriers. The Z-scheme charge transfer mechanism was proposed. This discovery comes up with a new strategy for the development of an efficient, environmentally friendly, and sustainable sulfide quantum dots/polymer non-noble metal photocatalyst.

Synergy of heterojunction and interfacial strain for boosting photocatalytic H2 evolution of black phosphorus nanosheets

As an emerging post-graphene two-dimensional material, black phosphorus (BP) has attracted enormous interest as a promising cocatalyst for photocatalytic hydrogen (H₂) evolution, however, the activity of either pristine bulk or BP nanosheets is far from satisfactory. Herein, we present an effective strategy to greatly boost the H₂ evolution performance of BP via applying the synergistic effect of heterojunction and interfacial lattice strain. A multilayered heterostructure coupling BP nanosheets and nickel oxide (NiO) nanosheets with abundant interface P-Ni and PO bonds is synthesized and utilized as a proof-of-concept material for our design. Both the experimental and theoretical results have revealed that the strain is formed in BP-NiO multilayered heterostructure. The generated lattice strain induces the charge redistribution at the interface between BP and NiO, which leads to the improved electron transfer efficiency and favorable H* adsorption kinetics for photocatalytic H₂ evolution reaction. As a result, the BP-NiO heterostructure with strain effect exhibits much enhanced photocatalytic H₂ evolution activity in the presence of Eosin Y (EY) as photosensitizer, exceeding that of zero-strained BP/NiO heterostructure and many other reported noble-metal-free cocatalyst.

A Critical Review on Black Phosphorus-Based Photocatalytic CO2 Reduction Application

Energy shortages and greenhouse effects are two unavoidable problems that need to be solved. Photocatalytically converting CO₂ into a series of valuable chemicals is considered to be an effective means of solving the above dilemmas. Among these photocatalysts, the utilization of black phosphorus for CO₂ photocatalytic reduction deserves a lightspot not only for its excellent catalytic activity through different reaction routes, but also on account of the great preponderance of this relatively cheap catalyst. Herein, this review offers a summary of the recent advances in synthesis, structure, properties, and application for CO₂ photocatalytic reduction. In detail, the review starts from the basic principle of CO₂ photocatalytic reduction. In the following section, the synthesis, structure, and properties, as well as CO₂ photocatalytic reduction process of black phosphorus-based photocatalyst are discussed. In addition, some possible influencing factors and reaction mechanism are also summarized. Finally, a summary and the possible future perspectives of black phosphorus-based photocatalyst for CO₂ reduction are established.

Activating Carbon Nitride by BP@Ni for the Enhanced Photocatalytic Hydrogen Evolution and Selective Benzyl Alcohol Oxidation

Two-dimensional (2D) semiconductors are promising photocatalysts; in order to overcome the relatively low efficiency of single-component 2D photocatalysts, heterostructures are fabricated for effective charge separation. Herein, a 2D heterostructure is synthesized by anchoring nickel nanoparticle-decorated black phosphorus (BP) nanosheets to graphitic carbon nitride (CN) nanosheets (CN/BP@Ni). The CN/BP@Ni heterostructure exhibits an enhanced charge separation due to the tight interfacial interaction and the cascaded electron-transfer channel from CN to BP and then to Ni nanoparticles. Possessing abundant active sites of Ni and P-N coordinate bonds, CN/BP@Ni shows a high visible-light-driven H₂ evolution rate of 8.59 mmol·h^-1·g^-1 with the sacrificial agent EtOH, about 10-fold to that of CN/BP. When applying benzyl alcohol to consume photogenerated holes, CN/BP@Ni enables the selective production of benzaldehyde; therefore, two value-added products are obtained in a single closed redox cycle. This work provides new insights into the development of photocatalysts without non-noble metals.

Aqueous Affinity and Interfacial Dynamics of Anisotropic Buckled Black Phosphorous

The structure of black phosphorous (BP) is similar to the honeycomb arrangement of graphene, but the layered BP is found to be buckled and highly anisotropic. The buckled surface structure affects interfacial molecule mobility and plays a vital role in various nanomaterial applications. The BP is also known for wettability, droplet formation, stability, and hydrophobicity in the aqueous environment. However, there is a gap concerning the structural and dynamical behavior of water molecules, which is available in abundance for other monoatomic and polyatomic two-dimensional (2D) materials. Motivated by the technological importance, we try to bridge the gap by explaining the surface anisotropy-facilitated behavior of water molecules on bilayer BP using classical and first principles molecular dynamics (MD) simulations. From our classical MD study, we find three distinct layers of water molecules. The water layer closest to the interface is L1, followed by L2 and L3/bulk perpendicular to the BP surface. Water molecules in the L1 layer experience some structural disintegration in hydrogen bond (HB) phenomena compared to the bulk. There is a loss of HB donor-acceptor count per water molecule. The average HB count decreases because of an elevated rate of HB formation and deformation; this would affect the dynamic properties in terms of HB lifetime. Therefore, we observe the reduced lifetime of HB in the layer in close contact with BP, which again complements our finding on the diffusion coefficient of water molecules in distinct layers. Water diffuses relatively faster with diffusion coefficient 3.25 × 10^-9 m² s^-1 in L1, followed by L2 and L3. The BP layer shows moderate hydrophobic nature. Our results also indicate the anisotropic behavior as the diffusion along the x-direction is faster than that along the y-direction. The gap in the slope of the x and y components of mean-squared displacement (MSD) complements the pinning effect in an aqueous environment. We observe blue-shifted and red-shifted libration and O-H stretching modes from the calculated power spectra for the L1 water molecules compared to the L2 and L3 molecules from first principles MD simulations. Our analysis may help understand the physical phenomena that occur during the surface wetting of the predroplet formation process observed experimentally.

Constructing Zn-P charge transfer bridge over ZnFe2O4-black phosphorus 3D microcavity structure: Efficient photocatalyst design in visible-near-infrared region

Black phosphorus (BP) is one of the most promising visible-near-infrared light-driven photocatalysts with favorite photoelectric properties and unique tunable direct band gap. Nevertheless, the further development of BP is hindered by the fast carrier recombination rate and high Gibbs free energy. Herein, an innovative strategy is developed for the controllable construction of Zn-P bonds induced zinc ferrite/black phosphorus (ZnFe₂O₄-BP) three dimensions (3D) microcavity structure. The Zn-P bonds serve as an efficient channel to optimize the carrier transport and Gibbs free energy of BP simultaneously. Besides, the unique 3D core-shell microcavity structure maintains the multiple reflections of sunlight inside the catalysts, which greatly improves the sunlight utilization upon photocatalysis. An optimized photocatalytic hydrogen production rate of 560 µmol h^-1g^-1 under near-infrared light (>820 nm) is achieved. A possible photocatalytic mechanism is proposed based on a series of experimental characterizations and theoretical calculations, this work provides a new sight to design high-quantity BP-based full-spectrum photocatalysts for solar energy conversion.

2D phosphorene nanosheets, quantum dots, nanoribbons: synthesis and biomedical applications

Phosphorene, also known as black phosphorus (BP), is a two-dimensional (2D) material that has gained significant attention in several areas of current research. Its unique properties such as outstanding surface activity, an adjustable bandgap width, favorable on/off current ratios, infrared-light responsiveness, good biocompatibility, and fast biodegradation differentiate this material from other two-dimensional materials. The application of BP in the biomedical field has been rapidly emerging over the past few years. This article aimed to provide a comprehensive review of the recent progress on the unique properties and extensive medical applications for BP in bone, nerve, skin, kidney, cancer, and biosensing related treatment. The details of applications of BP in these fields were summarized and discussed.

Advancing Applications of Black Phosphorus and BP-Analog Materials in Photo/Electrocatalysis through Structure Engineering and Surface Modulation

Black phosphorus (BP), an emerging 2D material semiconductor material, exhibits unique properties and promising application prospects for photo/electrocatalysis. However, the applications of BP in photo/electrocatalysis are hampered by the instability as well as low catalysis efficiency. Recently, tremendous efforts have been dedicated toward modulating its intrinsic structure, electronic property, and charge separation for enhanced photo/electrocatalytic performance through structure engineering. Simultaneously, the search for new substitute materials that are BP-analogous is ongoing. Herein, the latest theoretical and experimental progress made in the structural/surface engineering strategies and advanced applications of BP and BP-analog materials in relation to photo/electrocatalysis are extensively explored, and a presentation of the future opportunities and challenges of the materials is included at the end.