CdS@MoS2 Hetero-structured Nanocomposites Are Highly Effective Photo-Catalysts for Organic Dye Degradation

Sunlight-activated heterostructure MoS2/CdS nanocomposite photocatalyst with enhanced photocatalytic activity: band alignment and mechanism study

A high recombination rate is a major limiting factor in photocatalysis. Mitigating recombination through material engineering and photocatalyst optimization is key to enhancing photocatalytic performance. In this study, a heterostructure MoS2/CdS nanocomposite was synthesized through a hydrothermal method in a Teflon-lined autoclave subjected to a temperature of 200 °C for 16 hours. The resulting photocatalysts were characterized using a variety of techniques to understand their structural, surface, and optical properties. The photocatalytic activity of the as-synthesized photocatalysts was investigated by degrading methyl orange dye under both sunlight and visible light irradiation. Regardless of its MoS2 content, the heterostructure MoS2/CdS NC exhibited enhanced degradation efficiency relative to that of pure CdS, MoS2, and commercial TiO2 P25, with 5 wt% MoS2/CdS NCs exhibiting the highest degradation performance among all the evaluated photocatalysts. This behavior was justified by improved charge separation and reduced charge recombination, which were attributed to the valence band and conduction band offsets at the MoS2/CdS interface, as evidenced by band alignment study. The enhanced charge separation and reduced charge recombination were further validated by photoluminescence (PL), electrochemical impedance spectroscopy (EIS) and linear sweep voltammetry (LSV) measurements. Furthermore, an active species trapping experiment confirmed that electron transfer to oxygen and the subsequent formation of superoxide anions (O2 -) radical play the most significant roles in photocatalytic degradation under visible light illumination. Finally, the ability to reuse the MoS2/CdS NCs multiple times without substantial loss of activity evidenced their stability, thus paving the way for advancements in large-scale environmental remediation and other industrial applications.

MoS2-CdS composite for photocatalytic reduction of hexavalent chromium and thin film optoelectronic device applications

We introduce an enhanced light-harvesting MoS2-based nanocomposite exhibiting improved solar light induced photocurrent generation, both in solution and solid phases. The MoS2-CdS composite was synthesized via easy to achieve, cost effective, two-step solution process for the photocatalytic potassium dichromate [Cr(VI)] reduction and photocurrent generation in thin-film optoelectronic devices. Incorporating 10 wt% MoS2 into the composite increased the degradation efficiency of CdS from 43.9 to 91.9%. Furthermore, the MoS2-CdS composite demonstrated a 2.88-fold increase in the degradation rate constant and a 2.15% enhancement in the apparent quantum yield compared to controlled CdS. Additionally, the electrical power consumption per order decrease in Cr(VI) reduced from 25.74 kWh m-3 for controlled CdS to 9 kWh m-3 aimed at 10 wt% MoS2-CdS composite, indicating optimal synergy between the counterparts of MoS2-CdS in its composite. The resulting thin-film device with 10 wt% MoS2-CdS exhibited robust photocurrent generation and nonlinear I-V characteristics under solar illumination, attributed to the unique electronic properties of the MoS2-CdS heterojunction, influencing carrier transport via band alignment and interface carrier trapping effects. Moreover, photocurrent generation increased linearly with illumination intensity, and dynamic photo response studies revealed rapid photocurrent generation under illumination. Furthermore, the optoelectronic key parameters of CdS, including photosensitivity, photoresponsivity, and detectivity, were enhanced by factors of 5.09, 3.33, and 12.3, respectively, upon composite formation with MoS2. This study offers novel insights into developing high-performance and cost-effective bimetallic sulfide photocatalysts for efficient solar light-induced photocurrent generation in both solution and solid phases.

Effect of CdS loading on the properties and photocatalytic activity of MoS2 nanosheets

Molybdenum sulfide (MoS2) and modified MoS2 with different percentages of CdS (10%, 30%, and 50% CdS@MoS2) were successfully synthesized and characterized. The photocatalytic performance of the MoS2 and CdS@MoS2 was evaluated by degrading brilliant green (BG), methylene blue (MB), and rhodamine B (RhB) dyes under visible light irradiation. Amongst the synthesized photocatalysts, 50% CdS@MoS2 exhibited the highest photocatalytic activity, degrading 97.6%, 90.3%, and 75.5% of BG, MB, and RhB dyes, respectively within 5 h. The active species involved in the degradation processes were investigated. All trapping agents inhibited BG and MB degradation to a similar extent, indicating that all of the probed active species play an important role in the degradation of BG and MB. In contrast, h+ and O2•- were found to be the main reactive species in the photocatalytic RhB degradation. A potential mechanism for the photocatalytic degradation of dyes using CdS@MoS2 has been proposed. This work highlights the potential of CdS@MoS2 as a photocatalyst for more efficient water remediation applications.

NiO/MnFe2O4 Nanocomposite Photoluminescence, Structural, Morphological, Magnetic, and Optical Properties: Photocatalytic Removal of Cresol Red under Visible Light Irradiation

In this study, pure nickel oxide (NiO), manganese ferrite (MnFe2O4 or MFO), and binary nickel oxide/manganese ferrite (NiO/MFO1-4) nanocomposites (NCs) were synthesized using the Sol-Gel method. A comprehensive investigation into their photoluminescence, structural, morphological, magnetic, optical, and photocatalytic properties was conducted. Raman analysis, UV-Vis spectroscopy, Fourier-transform infrared spectroscopy, scanning electron microscopy, and X-ray diffraction techniques were used to characterize the materials. The synthesized samples exhibited superparamagnetic behavior, as revealed by our analysis of their magnetic properties. A lower recombination rate was shown by the photoluminescence analysis, which is helpful for raising photocatalytic activity. The photocatalytic activity was evaluated for the degradation of Cresol Red (CR) dye. 91.6% of CR dye was degraded by NiO/MFO-4 nanocomposite, and the NC dosage as well as solution pH affected the photocatalytic performance significantly. In four sequential photocatalytic cycles, the magnetically separable NCs were stable and recyclable. The enhanced photocatalytic activity and magnetic separability revealed the potential application of NiO/MFO-4 as an efficient photocatalyst for the removal of dyes from industrial wastewater under solar light irradiation.

A Review on Low-Dimensional Nanomaterials: Nanofabrication, Characterization and Applications

The development of modern cutting-edge technology relies heavily on the huge success and advancement of nanotechnology, in which nanomaterials and nanostructures provide the indispensable material cornerstone. Owing to their nanoscale dimensions with possible quantum limit, nanomaterials and nanostructures possess a high surface-to-volume ratio, rich surface/interface effects, and distinct physical and chemical properties compared with their bulk counterparts, leading to the remarkably expanded horizons of their applications. Depending on their degree of spatial quantization, low-dimensional nanomaterials are generally categorized into nanoparticles (0D); nanorods, nanowires, and nanobelts (1D); and atomically thin layered materials (2D). This review article provides a comprehensive guide to low-dimensional nanomaterials and nanostructures. It begins with the classification of nanomaterials, followed by an inclusive account of nanofabrication and characterization. Both top-down and bottom-up fabrication approaches are discussed in detail. Next, various significant applications of low-dimensional nanomaterials are discussed, such as photonics, sensors, catalysis, energy storage, diverse coatings, and various bioapplications. This article would serve as a quick and facile guide for scientists and engineers working in the field of nanotechnology and nanomaterials.

Novel fabrication of the recyclable MoS2/Bi2WO6 heterostructure and its effective photocatalytic degradation of tetracycline under visible light irradiation

Developing cost-effective and highly effective visible-light-driven photocatalysts for decomposition of organic contaminants has been deliberated as an important and viable strategy for environmental remediation. Herein, MoS₂/Bi₂WO₆ heterostructure photocatalysts were fabricated with excellent visible light absorption performance and efficient electron/hole (e^-/h⁺) separation efficacy. As-prepared all photocatalysts were systematically characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), transmission electron microscopy (TEM), high resolution TEM, X-ray photoelectron spectroscopy (XPS). Although photocatalytic experiments were examined by UV-vis diffuse reflectance spectroscopy (UV-vis DRS), photoluminescence spectroscopy (PL), and transient photocurrent (I-t). Among all the photocatalysts, that synthesized by using the components 10 mg of Bi₂WO₆ with 100 mg of MoS₂ (denoted as MSBW-10), displayed high photocatalytic performance (96.31%) for tetracycline (TC) under visible light irradiation within 90 min. The kinetic rate constant of the MSBW-10 heterostructure was 5.51 and 6.71 times higher than those of MoS₂ and Bi₂WO₆, respectively. Further, radical trapping experiments revealed that ˙OH radicals and holes were the predominant reactive species involved in the photocatalytic course. The recycle tests revealed the stability of the photocatalyst, which exhibited 91.85% TC removal efficacy without obvious decay even after the fourth cycle. Furthermore, the type-II MoS₂/Bi₂WO₆ heterostructure photocatalyst exhibited a slighter band gap with energy band alignments and enhanced visible-light absorption, separation of charge carriers, and good oxidation/reduction capacities. These deeper insights and synergetic effects can afford a new approach for flourishing novel heterostructure photocatalysts.

Construction of S-scheme CdS/g-C3N4 nanocomposite with improved visible-light photocatalytic degradation of methylene blue

Within moderate band gap, g-C3N4 and CdS are both promising visible light driven photocatalysts. However, their intrinsic high recombination rate of photo-induced electron-hole pairs along with the poor susceptibility in photocorrosion of CdS is main limitations hindering their practical application. In this study, the CdS/g-C3N4 composites with various weight ratios of CdS to g-C3N4 were solvothermal prepared from the dispersion of components, g-C3N4 and CdS, in ethanol. The physicochemical characterizations demonstrate the success in the fabrication of well-dispersed CdS nanoparticles in the g-C3N4 matrix. The enhanced photocatalytic activity of the g-C3N4/CdS composite over the degradation of methylene blue under visible light was ascribed to the effective photo-induced electron-hole separation via the step scheme (S-scheme) pathway in which the main contribution of high oxidative hydroxyl radicals (•OH) was demonstrated. Furthermore, via S-scheme model, we also clarify the depletion of photo-induced holes on CdS which is ascribed as the reason for improvement in resistance to photocorrosion of composites.

Self-Assembled Nanocomposites and Nanostructures for Environmental and Energy Applications

Self-assembled nanocomposites are attracting considerable attention owing to their controllable architectures and self-assembly processes, as well as the increase in worldwide environmental effects and energy needs. Further understanding of the self-assembly procedure for improving environmental and energy applications would advance the design and manufacture of nanomaterials for various applications. These materials can be grouped into major categories for various application fields, including powder photocatalysts, membrane photocatalysts, and thin-film thermoelectric nanomaterials. These self-assembled nanomaterials can be used for environmental and energy applications, such as wastewater purification, hydrogen production by water splitting, energy storage, and energy harvesting. In this review, a brief introduction to the definitions and classifications of self-assembled nanocomposites is provided. We aim to provide a summary of the recent research related to self-assembled nanocomposites and nanostructures used for environmental and energy applications. Moreover, typical examples and discussions are aimed at demonstrating the advantages of self-assembled nanostructures. At the end of each section, the structural properties and the application of the nanocomposite or nanostructure are summarized. Finally, we provide perspectives for future research on the design and fabrication of self-assembled nanocomposites and nanostructures.

Cadmium Sulfide 3D Photonic Crystal with Hierarchically Ordered Macropores for Highly Efficient Photocatalytic Hydrogen Generation

Cadmium sulfide is a potential candidate for photocatalytic water splitting. However, CdS nanoparticles have a high recombination rate of photoinduced carriers induced by aggregation. Therefore, decreasing the recombination rate and increasing the migration rate of photogenerated carriers are essential to drive the development and application of CdS in hydrogen production. In this study, we design CdS with a three-dimensional ordered macroporous (3DOM) structure using polymethylmethacrylate as a template. It not only retains the excellent visible light response of CdS but also improves the easy recombination of photogenerated carriers in CdS nanoparticles by taking advantage of the unique ability of mass transfer, charge separation, and migration in the 3DOM structure. Meanwhile, the highly ordered periodic structure of 3DOM CdS can produce a slow photon effect of photonic crystals to obtain more photoinduced carriers. In particular, we found that a suitable stop-band position is beneficial to maximize the utilization of the slow photon effect. The photocatalytic hydrogen evolution rate of Pt-CdS is considerably improved after constructing the 3DOM structure. This study provides a new design strategy of ordered macroporous sulfide catalysts to achieve high photocatalytic activity.

Enhancing the photocatalytic hydrogen production activity of BiVO4 [110] facets using oxygen vacancies

The activity of the hydrogen evolution reaction (HER) during photoelectrochemical (PEC) water-splitting is limited when using BiVO₄ with an exposed [110] facet because the conduction band minimum is below the H⁺/H₂O potential. Here, we enhance the photocatalytic hydrogen production activity through introducing an oxygen vacancy. Our first-principles calculations show that the oxygen vacancy can tune the band edge positions of the [110] facet, originating from an induced internal electric field related to geometry distortion and charge rearrangement. Furthermore, the induced electric field favors photogenerated electron-hole separation and the enhancement of atomic activity. More importantly, oxygen-vacancy-induced electronic states can increase the probability of photogenerated electron transitions, thus improving optical absorption. This study indicates that oxygen-defect engineering is an effective method for improving the photocatalytic activity when using PEC technology.

Highly Efficient Simulated Solar Light-Driven Photocatalytic Degradation of 4-Nitrophenol over CdS/Carbon/MoSx Hybrids

Among the various organic pollutants and industrial chemicals, 4-nitrophenol has been one of the most monitored substances in aqueous environments, due to its enhanced solubility in such systems. This research reports for the first time the microwave-assisted synthesis of CdS/carbon/MoS_x hybrids and the subsequent utilization of such systems as photocatalysts for 4-nitrophenol degradation. The hybrids demonstrated a variable photocatalytic activity, by using a variety of organic substances as precursors for the solvothermal carbonization step. By using ascorbic acid as precursor, the corresponding ternary composite exhibited excellent photocatalytic activity, with the 4-nitrophenol concentration been almost quantitatively decayed within 45 min of irradiation. This could be ascribed due to the generation of a high population of heterojunctions as well as the chemical speciation of Mo-based nanostructures. Such ternary hybrids may be utilized as potential photocatalytic systems in processes, where removal of toxic water-soluble substances is the key issue.

Flower-like MoS2 microspheres compounded with irregular CdS pyramid heterojunctions: highly efficient and stable photocatalysts for hydrogen production from water

An irregular CdS pyramid/flower-like MoS₂ microsphere composite photocatalyst was successfully synthesized using a simple one-step hydrothermal method. The as-prepared samples were characterized by X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy, ultraviolet visible absorption spectroscopy, fluorescence spectroscopy and photoelectrochemical tests. The composite photocatalysts showed superior photocatalytic activities for hydrogen evolution from water under visible light irradiation (λ ≥ 420 nm) with an extremely high apparent quantum yield (AQY = 64.8%) at 420 nm. To our knowledge, this value is the highest reported efficiency value for CdS/MoS₂ photocatalysts. Further detailed characterization revealed that the special structure for some CdS pyramid structures dispersed in the MoS₂ microsphere structures and surrounded by MoS₂ nanosheets led to the photogenerated electrons migrating from the conduction band of different faces of the CdS pyramid to the conduction band of different MoS₂ nanosheets while photogenerated holes remained in the CdS pyramid structures, which greatly promoted the separation of photogenerated electrons and holes, improving the photoactivity of the CdS/MoS₂ catalyst. The catalyst also exhibited perfect stability, and the photoactivity displayed no significant degradation during continuous hydrogen production over nearly 70 h.

Schematic diagram of the photogenerated carrier migration between CdS and MoS₂.