Mechanistic Study of Alcohol Dehydration on γ-Al2O3

Ferromanganese oxide-functionalized TiO2 for rapid catalytic ozonation of PPCPs through a coordinated oxidation process with adjusted composition and strengthened generation of reactive oxygen species

Ferromanganese oxide (MFOx) was first utilized to functionalize TiO2 and an MFOx@TiO2 catalyst was developed for catalytic ozonation for rapid attack of pharmaceutical and personal care products (PPCPs) with adjusted reactive oxygen species (ROSs) composition and strengthened ROSs generation. Unlike Al2O3, which strongly relied on adsorption and was significantly influenced by MFOx loading, synergistic catalytical effects of MFOx and TiO2 were observed, and optimal MFOx doping of 2 wt% and MFOx@TiO2 dosage of 500 ppm were obtained for catalyzing ozonation. In ibuprofen (IBP) degradation, MFOx@TiO2-catalyzed ozonation (MFOx@TiO2/O3) obtained 2.0-, 4.7- and 6.9-folds the kobs of TiO2/O3, MFOx/O3 and bare ozonation (B/O3). Stronger O3 decomposition was observed by MFOx@TiO2 over bare TiO2 with the participation of redox pairs Fe(II)/Fe(III) and Mn(II)/Mn(III)/Mn(IV) and increased surface oxygen vacancies (SOVs) from 9.8 % to 33.7 % was detected. The results revealed that Fe(II), Mn(II) and Mn(III) with low valance accelerated Ti(III) generation from Ti(VI), obtaining an unprecedented high Ti(III) composition occupying 35.3 % of the total Ti atoms. Ti(III) catalyzed the direct reduction of SOVs-O2 to •O2-, and it accelerated the formation of Ti(VI)-OH and Ti(VI)-O which catalyzed O3 decomposition into •O2-. •O2- was found to primarily initiate IBP degradation with nucleophilic addition and dominated over 66 % IBP removal. The enhanced •O2- generation further strengthened •OH and 1O2 production. MFOx@TiO2/O3 obtained 17 %, 21 % and 30 % higher TOC removal over TiO2/O3, MFOx/O3 and B/O3, respectively. Acute toxicity tests confirmed the effective toxicity control of organics by MFOx@TiO2/O3 process (inhibition rate: 10.9 %). Degradation test of atenolol and sulfamethoxazole confirmed the catalytic effects of MFOx@TiO2. MFOx@TiO2 performed strong resistance to water matrix in application test and showed good stability and reusability. The study proposed an effective catalyst for strengthening the ozonation process on PPCPs degradation and provided an in-depth understanding of the mechanisms and characteristics of the MFOx@TiO2 catalyst and MFOx@TiO2/O3 process.

Disentangling Origins of Adhesive Bonding at Interfaces between Epoxy/Amine Adhesive and Aluminum

Joining metals by adhesive bonding is essential in widespread fields such as mobility, dentistry, and electronics. Although adhesive technology has grown since the 1920s, the roles of interfacial phenomena in adhesive bonding are still elusive, which hampers the on-demand selection of surface treatment and adhesive types. In the present study, we clarified how chemical interactions and mechanical interlocking governed adhesive bonding by evaluating adhesion properties at the interfaces between epoxy/amine adhesive and two kinds of Al adherends: a flat aluminum hydroxide (Al_xO_yH_z) and technical Al plate with roughness. Spectroscopic and microscopical data demonstrate that the protonation of the amino groups in an amine hardener converts Al(OH)₃ on the Al_xO_yH_z surface to AlO(OH). The interfacial protonation results in an interfacial dipole layer with positive charges on the adhesive side, whose electrostatic interaction increases the interfacial fracture energy. The double cantilever beam tests for the flat Al_xO_yH_z and technical Al substrates clarify that the mechanical interlocking originating from the surface roughness further increases the fracture energy. This study disentangles the roles of the chemical interactions and mechanical interlocking occurring at the epoxy adhesive/Al interface in the adhesion mechanism.

Tuning the reactivity of carbon surfaces with oxygen-containing functional groups

Oxygen-containing carbons are promising supports and metal-free catalysts for many reactions. However, distinguishing the role of various oxygen functional groups and quantifying and tuning each functionality is still difficult. Here we investigate the role of Brønsted acidic oxygen-containing functional groups by synthesizing a diverse library of materials. By combining acid-catalyzed elimination probe chemistry, comprehensive surface characterizations, ¹⁵N isotopically labeled acetonitrile adsorption coupled with magic-angle spinning nuclear magnetic resonance, machine learning, and density-functional theory calculations, we demonstrate that phenolic is the main acid site in gas-phase chemistries and unexpectedly carboxylic groups are much less acidic than phenolic groups in the graphitized mesoporous carbon due to electron density delocalization induced by the aromatic rings of graphitic carbon. The methodology can identify acidic sites in oxygenated carbon materials in solid acid catalyst-driven chemistry.

Assessing the Effect of Dopants on the C-H Activation Activity of γ-Al2 O3 using First-Principles Calculations

In recent years, the high availability of methane in the shale gas reserves has raised significant interest in its conversion to high-value chemicals but this process is still not commercially viable. Metal oxides, due to their surface heterogeneity and the presence of Lewis acidic and basic site pairs are known to facilitate the activation of C-H bonds of methane. In this work, we investigate the C-H bond activation of methane on pristine and doped γ-Al₂ O₃ clusters using density functional theory (DFT) calculations. Our results demonstrate that the polar pathway is energetically preferred over the radical pathway on these systems. We found that the metal dopants (boron and gallium) not only alter the catalytic activity of dopant sites but this effect is more pronounced on some of the adjacent sites (non-local). Among the selected dopants, gallium greatly improves the catalytic activity on most of the site pairs (including most active and least active) of pristine γ-Al₂ O₃ . Additionally, we identified a correlation between H₂ binding energies and the C-H activation free energies on Ga-doped γ-Al₂ O₃ .

Facile Ozonation of Light Alkanes to Oxygenates with High Atom Economy in Tunable Condensed Phase at Ambient Temperature

We have demonstrated the oxidation of mixed alkanes (propane, n-butane, and isobutane) by ozone in a condensed phase at ambient temperature and mild pressures (up to 1.3 MPa). Oxygenated products such as alcohols and ketones are formed with a combined molar selectivity of >90%. The ozone and dioxygen partial pressures are controlled such that the gas phase is always outside the flammability envelope. Because the alkane-ozone reaction predominantly occurs in the condensed phase, we are able to harness the unique tunability of ozone concentrations in hydrocarbon-rich liquid phases for facile activation of the light alkanes while also avoiding over-oxidation of the products. Further, adding isobutane and water to the mixed alkane feed significantly enhances ozone utilization and the oxygenate yields. The ability to tune the composition of the condensed media by incorporating liquid additives to direct selectivity is a key to achieving high carbon atom economy, which cannot be achieved in gas-phase ozonations. Even in the liquid phase, without added isobutane and water, combustion products dominate during neat propane ozonation, with CO₂ selectivity being >60%. In contrast, ozonation of a propane+isobutane+water mixture suppresses CO₂ formation to 15% and nearly doubles the yield of isopropanol. A kinetic model based on the formation of a hydrotrioxide intermediate can adequately explain the yields of the observed isobutane ozonation products. Estimated rate constants for the formation of oxygenates suggest that the demonstrated concept has promise for facile and atom-economic conversion of natural gas liquids to valuable oxygenates and broader applications associated with C-H functionalization.

A multi-faceted structural, thermodynamic, and spectroscopic approach for investigating ethanol dehydration over transition phase aluminas

The surface-catalyzed dehydration of ethanol over transition phase aluminas was studied using a multi-faceted structural and thermodynamic characterization approach, which enabled a detailed examination of the reaction mechanism using INS.

Alumina Graphene Catalytic Condenser for Programmable Solid Acids

Precise control of electron density at catalyst active sites enables regulation of surface chemistry for the optimal rate and selectivity to products. Here, an ultrathin catalytic film of amorphous alumina (4 nm) was integrated into a catalytic condenser device that enabled tunable electron depletion from the alumina active layer and correspondingly stronger Lewis acidity. The catalytic condenser had the following structure: amorphous alumina/graphene/HfO₂ dielectric (70 nm)/p-type Si. Application of positive voltages up to +3 V between graphene and the p-type Si resulted in electrons flowing out of the alumina; positive charge accumulated in the catalyst. Temperature-programmed surface reaction of thermocatalytic isopropanol (IPA) dehydration to propene on the charged alumina surface revealed a shift in the propene formation peak temperature of up to ΔT _peak∼50 °C relative to the uncharged film, consistent with a 16 kJ mol^-1 (0.17 eV) reduction in the apparent activation energy. Electrical characterization of the thin amorphous alumina film by ultraviolet photoelectron spectroscopy and scanning tunneling microscopy indicates that the film is a defective semiconductor with an appreciable density of in-gap electronic states. Density functional theory calculations of IPA binding on the pentacoordinate aluminum active sites indicate significant binding energy changes (ΔBE) up to 60 kJ mol^-1 (0.62 eV) for 0.125 e^- depletion per active site, supporting the experimental findings. Overall, the results indicate that continuous and fast electronic control of thermocatalysis can be achieved with the catalytic condenser device.

Morphology dependent effect of γ-Al2O3 for ethanol dehydration: nanorods and nanosheets

γ-Al2O3 nanorods gave the improved selectivity of C2H4 in ethanol dehydration due to the selective exposure of {100} facets.

The Effect of Pristine and Hydroxylated Oxide Surfaces on the Guaiacol HDO Process: A DFT Study

The acid‐base character of oxide supports is crucial for catalytic reactions. In this work, the acid‐base properties of five oxide surfaces common in heterogeneous catalysis were investigated and related to their interaction with monolignol compounds derived from lignin. We have used density functional theory simulations also to understand the role of the surfaces’ hydroxylation state. The results show that moderate hydroxyl coverage on the amphoteric γ‐Al₂O₃ (110) slightly strengthens the oxy‐compounds’ adsorption due to an increase in Lewis acidity. Similarly, low hydroxyl coverage on the reducible TiO₂ (101) enlarges its adsorption capacity by up to 42 % compared with its clean surface. The higher affinity is attributed to the more favourable interaction between the surface‐OH groups and the aromatic rings. Overall, the results indicate that hydroxyl coverage enhances the amphoteric and reducible adsorption capacity towards aromatic species.

Two-Dimensional Perovskite Crystals Formed by Atomic Layer Deposition of CaTiO3 on γ-Al2O3

CaTiO₃ films with an average thickness of 0.5 nm were deposited onto γ-Al₂O₃ by Atomic Layer Deposition (ALD) and then characterized by a range of techniques, including X-ray Diffraction (XRD) and High-Resolution, Transmission Electron Microscopy (HRTEM). The results demonstrate that the films form two-dimensional crystallites over the entire surface. Lattice fringes from HRTEM indicate that the crystallites range in size from 5 to 20 nm and are oriented in various directions. Films of the same thickness on SiO₂ remained amorphous, indicating that the support played a role in forming the crystallites.

Selective Production of Bio-Based Linear Alpha-Olefin from Wasted Fatty Alcohol on Al2O3 for Bio-Based Chemicals

The catalytic dehydration of a bio-based fatty alcohol was performed using Al2O3 prepared by solvothermal synthesis for selective production of long-chain linear-alpha-olefins (LAO). The effect of the synthesis temperature of alumina precursors on the dehydration of 1-octadecanol (C18H38O) was examined based on the textural properties and Lewis acid-base properties of the catalysts. Amorphous alumina synthesized at 325 °C showed the highest surface area (233.07 m2/g) and total pore volume (1.237 cm3/g) among the catalysts and the best dehydration results: 93% conversion, 62% selectivity of 1-octadecene (C18H36), and 89% LAO purity. This was attributed to the increased Al/O ratio and atomic concentration of surface O in alumina, which were important factors in the catalytic dehydration of 1-octadecanol through the synergistic catalysis of acid-base pairs. The produced bio-based LAO can be key intermediates for synthesis of oxo alcohols and poly-alpha-olefins, as alternatives to petroleum-based LAO to achieve carbon neutrality in chemical industry.

Pair Sites on Nodes of Metal-Organic Framework hcp UiO-66 Catalyze tert-Butyl Alcohol Dehydration

On metal oxide cluster nodes of metal-organic frameworks (MOFs), sites not bonded to linkers (e.g., defects and structural vacancies) control reactivity and catalysis. Attention has been focused on isolated, individual sites, but pair sites have been largely overlooked. We now show that the MOF hcp UiO-66, which incorporates dimeric Zr₆O₈ nodes bridged by μ₂-OH groups, is an excellent platform for identifying and controlling adjacent sites consisting of OH groups and Zr⁴⁺ sites, which catalyze tert-butyl alcohol dehydration much more rapidly than isolated single sites.

Ethanol-ethylene conversion mechanism on hydrogen boride sheets probed by in situ infrared absorption spectroscopy

Two-dimensional hydrogen boride (HB) sheets were recently demonstrated to act as a solid acid catalyst in their hydrogen-deficient state. However, both the active sites and the mechanism of the catalytic process require further elucidation. In this study, we analyzed the conversion of ethanol adsorbed on HB sheets under vacuum during heating using in situ Fourier transform infrared (FT-IR) absorption spectroscopy with isotope labelling. Up to 450 K, the FT-IR peak associated with the OH group of the adsorbed ethanol molecule disappeared from the spectrum, which was attributed to a dehydration reaction with a hydrogen atom from the HB sheet, resulting in the formation of an ethyl species. At temperatures above 440 K, the number of BD bonds markedly increased in CD₃CH₂OH, compared to CH₃CD₂OH; the temperature dependence of the formation rate of BD bonds was similar to that of the dehydration reaction rate of ethanol on HB sheets under steady-state conditions. The rate-determining step of the dehydration of ethanol on HB was thus ascribed to the dehydrogenation of the methyl group of the ethyl species on the HB sheets, followed by the immediate desorption of ethylene. These results show that the catalytic ethanol dehydration process on HB involves the hydrogen atoms of the HB sheets. The obtained mechanistic insights are expected to promote the practical application of HB sheets as catalysts.

Renewable Butene Production through Dehydration Reactions over Nano-HZSM-5/γ-Al2O3 Hybrid Catalysts

The development of new, improved zeolitic materials is of prime importance to progress heterogeneous catalysis and adsorption technologies. The zeolite HZSM-5 and metal oxide γ-Al2O3 are key materials for processing bio-alcohols, but both have some limitations, i.e., HZSM-5 has a high activity but low catalytic stability, and vice versa for γ-Al2O3. To combine their advantages and suppress their disadvantages, this study reports the synthesis, characterization, and catalytic results of a hybrid nano-HZSM-5/γ-Al2O3 catalyst for the dehydration of n-butanol to butenes. The hybrid catalyst is prepared by the in-situ hydrothermal synthesis of nano-HZSM-5 onto γ-Al2O3. This catalyst combines mesoporosity, related to the γ-Al2O3 support, and microporosity due to the nano-HZSM-5 crystals dispersed on the γ-Al2O3. HZSM-5 and γ-Al2O3 being in one hybrid catalyst leads to a different acid strength distribution and outperforms both single materials as it shows increased activity (compared to γ-Al2O3) and a high selectivity to olefins, even at low conversion and a higher stability (compared to HZSM-5). The hybrid catalyst also outperforms a physical mixture of nano-HZSM-5 and γ-Al2O3, indicating a truly synergistic effect in the hybrid catalyst.

Site-Selective Nanoreactor Deposition on Photocatalytic Al Nanocubes

Photoactivation of catalytic materials through plasmon-coupled energy transfer has created new possibilities for expanding the scope of light-driven heterogeneous catalysis. Here we present a nanoengineered plasmonic photocatalyst consisting of catalytic Pd islands preferentially grown on vertices of Al nanocubes. The regioselective Pd deposition on Al nanocubes does not rely on complex surface ligands, in contrast to site-specific transition-metal deposition on gold nanoparticles. We show that the strong local field enhancement on the sharp nanocube vertices provides a mechanism for efficient coupling of the plasmonic Al antenna to adjacent Pd nanoparticles. A substantial increase in photocatalytic H₂ dissociation on Pd-bound Al nanocubes relative to pristine Al nanocubes can be observed, incentivizing further engineering of heterometallic antenna-reactor photocatalysts. Controlled growth of catalytic materials on plasmonic hot spots can result in more efficient use of the localized surface plasmon energy for photocatalysis, while minimizing the amount and cost of precious transition-metal catalysts.

Monomolecular Dehydration of Ethanol into Ethylene over H-MOR Studied by Density Functional Theory

The framework effect of H-mordenite (H-MOR) zeolite on monomolecular dehydration of ethanol to ethylene has been simulated based on density functional theory. It is indicated that both the reaction mechanism and the activation energy barriers are significantly affected by the pore-confinement effect. In the 12-membered ring (12-MR), the energy barriers of the stepwise mechanism and the concerted mechanism are 35.0 and 42.4 kcal mol^-1, respectively, suggesting that ethylene can be competitively formed through both pathways. While in the 8-membered ring (8-MR), the barrier of the concerted mechanism is 43.4 kcal mol^-1, which is much lower than that of the stepwise mechanism with the ethoxy intermediate formation barrier of 53.7 kcal mol^-1. Furthermore, the water molecule acts as the intermediate to stabilize the transition states (TSs) for both stepwise and concerted mechanisms and helps to transport protons during the reaction.

Synthesis of Dimethyl Ether via CO2 Hydrogenation: Effect of the Drying Technique of Alumina on Properties and Performance of Alumina-Supported Copper Catalysts

Thermal treatment during catalyst preparation is one of the important factors affecting the characteristics and performance of a catalyst. To improve the catalytic performance of an alumina-supported copper catalyst prepared by an impregnation method for dimethyl ether (DME) synthesis from CO₂, the effects of the use of hot air and infrared drying as well as calcination at 600 and 900 °C to prepare alumina supports were investigated. Infrared drying could shorten the required drying time by 75% when compared with hot air drying. Infrared drying could also help maintain the pore size and pore volume of the supports, leading to their larger surface areas. Different drying techniques were additionally noted to result in different sizes and shapes of the pores as well as to different copper distributions and intensities of acid sites of the catalyst. An increase in the calcination temperature resulted in a decrease in the surface area of the supports because of particle aggregation. The drying technique exhibited a more significant effect than calcination temperature on the space-time yield of DME. A catalyst utilizing the support prepared by infrared drying and then calcined at 600 °C exhibited the highest yield of DME (40.9 g_DME kg_cat ^-1 h^-1) at a reaction temperature of 300 °C. Stability of the optimal catalyst, when monitored over a 24 h period, was noted to be excellent.

Probing Interactions of γ-Alumina with Water via Multinuclear Solid-State NMR Spectroscopy

Interaction of γ-alumina with water are important in controlling its structure and catalytic properties. We apply solid-state multinuclear NMR spectroscopy to investigate this interaction by monitoring ¹H and ¹⁷O spectra in real-time. Surface-selective detection is made possible by adsorbing ¹⁷O-enriched water on γ-alumina nanorods. Structural evolution on the surface was selectively probed by ¹H/¹⁷O double resonance NMR and ²⁷Al NMR at ultrahigh 35.2 T magnetic field. Formation of hydroxyl species on the surface of nanorods is rapid upon the exposure of water, which involves low coordinated aluminum ions with doubly bridging and isolated hydroxyl species being generated first. Fast exchange occurs between oxygen atoms in the water molecules and bare surface sites, indicating high reactivity of these oxygen species. These results provide new insights into the structure and dynamics on the surface of γ-alumina and the methods applied here can be extended to study the interaction of other oxides with water.

The competition between dehydrogenation and dehydration reactions for primary and secondary alcohols over gallia: unravelling the effects of molecular and electronic structure via a two-pronged theoretical/experimental approach

The relative dehydrogenation/dehydration reactivity imparted by nanostructured gallium(iii) oxide on alcohols was investigated via electronic structure calculations, reactivity tests and DRIFT-IR spectroscopy.

Improving alkane dehydrogenation activity on γ-Al2O3 through Ga doping

Doping the surface of γ-Al₂O₃ with gallium enhances the alkane dehydrogenation catalytic activity.

Theoretical Determination of Size Effects in Zeolite-Catalyzed Alcohol Dehydration

In the upgrading of biomass pyrolysis vapors to hydrocarbons, dehydration accomplishes a primary objective of removing oxygen, and acidic zeolites represent promising catalysts for the dehydration reaction. Here, we utilized density functional theory calculations to estimate adsorption energetics and intrinsic kinetics of alcohol dehydration over H-ZSM-5, H-BEA, and H-AEL zeolites. The ONIOM (our Own N-layered Integrated molecular Orbital and molecular Mechanics) calculations of adsorption energies were observed to be inconsistent when benchmarked against QM (Quantum Mechanical)/Hartree–Fock and periodic boundary condition calculations. However, reaction coordinate calculations of adsorbed species and transition states were consistent across all levels considered. Comparison of ethanol, isopropanol (IPA), and tert-amyl alcohol (TAA) over these three zeolites allowed for a detailed examination of how confinement impacts on reaction mechanisms and kinetics. The TAA, seen to proceed via a carbocationic mechanism, was found to have the lowest activation barrier, followed by IPA and then ethanol, both of which dehydrate via a concerted mechanism. Barriers in H-BEA were consistently found to be lower than in H-ZSM-5 and H-AEL, attributed to late transition states and either elevated strain or inaccurately estimating long-range electrostatic interactions in H-AEL, respectively. Molecular dynamics simulations revealed that the diffusivity of these three alcohols in H-ZSM-5 were significantly overestimated by Knudsen diffusion, which will complicate experimental efforts to develop a kinetic model for catalytic fast pyrolysis.

Observation of an oxonium ion intermediate in ethanol dehydration to ethene on zeolite

Zeolite-catalyzed dehydration of ethanol offers promising perspectives for the sustainable production of ethene. Complex parallel-consecutive pathways are proposed to be involved in the reaction network of ethanol dehydration on zeolites, where the initial step of ethanol dehydration is still unclear particularly for the favorable production of ethene at lower temperature. Here we report the observation of a triethyloxonium ion (TEO) in the dehydration of ethanol on zeolite H-ZSM-5 by using ex situ and in situ solid-state NMR spectroscopy. TEO is identified as a stable surface species on the working catalyst, which shows high reactivity during reaction. Ethylation of the zeolite by TEO occurs at lower temperature, leading to the formation of surface ethoxy species and then ethene. The TEO-ethoxide pathway is found to be energetically preferable for the dehydration of ethanol to ethene in the initial stage, which is also supported by theoretical calculations.

Selective cleavage of lignin and lignin model compounds without external hydrogen, catalyzed by heterogeneous nickel catalysts

This work reports an economical and environmentally friendly, external hydrogen-free method for the selective cleavage of lignin and lignin model compounds into value-added chemicals.

Selective hydrogenolysis of the C_aryl–O bonds in lignin is a key strategy for the generation of fuels and chemical feedstocks from biomass. Currently, hydrogenolysis has been mainly conducted using hydrogen, which is flammable and not sustainable or economical. Herein, an external hydrogen-free process for aryl ethers hydrogenolysis in lignin models and dioxasolv lignin over nickel nanoparticles supported on Al₂O₃, is reported. Kinetic studies reveal that the transfer hydrogenolysis activity of the three model compounds decreased in the following order: benzyl phenyl ether (α-O-4), 2-phenylethyl phenyl ether (β-O-4) and diphenyl ether (4-O-5), which linearly corresponds to their binding energies and the activation energies. The main reaction route for the three model compounds was the cleavage of the ether bonds to produce aromatic alkanes and phenol, and the latter was further reduced to cyclohexanol. Dioxasolv lignin depolymerization results exhibit a significant C_aryl–O decrease over the Ni nanoparticles supported on Al₂O₃ with iso-propanol as the hydrogen source through 2D-HSQC-NMR analysis, which confirmed the transfer hydrogenolysis conclusion in the model study. This work provides an economical and environmentally-friendly method for the selective cleavage of lignin and lignin model compounds into value-added chemicals.

Application of modulation excitation-phase sensitive detection-DRIFTS for in situ/operando characterization of heterogeneous catalysts

A new more general method and guidelines for the implementation of modulation excitation-phase sensitive detection-diffuse reflectance Fourier transform spectroscopy (ME-PSD-DRIFTS).