CdSe Quantum Dot Sensitized Solar Cells. Shuttling Electrons Through Stacked Carbon Nanocups

Recent Trends in Plasmon-Assisted Photocatalytic CO2 Reduction

Direct photocatalytic reduction of CO₂ has become an highly active field of research. It is thus of utmost importance to maintain an overview of the various materials used to sustain this process, find common trends, and, in this way, eventually improve the current conversions and selectivities. In particular, CO₂ photoreduction using plasmonic photocatalysts under solar light has gained tremendous attention, and a wide variety of materials has been developed to reduce CO₂ towards more practical gases or liquid fuels (CH₄ , CO, CH₃ OH/CH₃ CH₂ OH) in this manner. This Review therefore aims at providing insights in current developments of photocatalysts consisting of only plasmonic nanoparticles and semiconductor materials. By classifying recent studies based on product selectivity, this Review aims to unravel common trends that can provide effective information on ways to improve the photoreduction yield or possible means to shift the selectivity towards desired products, thus generating new ideas for the way forward.

Anchoring Copper Single Atoms on Porous Boron Nitride Nanofiber to Boost Selective Reduction of Nitroaromatics

Single-atom catalysts have received widespread attention for their fascinating performance in terms of metal atom efficiency as well as their special catalysis mechanisms compared to conventional catalysts. Here, we prepared a high-performance catalyst of single-Cu-atom-decorated boron nitride nanofibers (BNNF-Cu) via a facile calcination method. The as-prepared catalyst shows high catalytic activity and good stability for converting different nitro compounds into their corresponding amines both with and without photoexcitation. By combined studies of synchrotron radiation analysis, high-resolution high-angle annular dark-field transmission electron microscopy studies, and DFT calculations, dispersion and coordination of Cu atoms as well as their catalytic mechanisms are explored. The BNNF-Cu catalyst is found to have a record high turnover frequency compared to previously reported non-precious-metal-based catalysts. While the performance of the BNNF-Cu catalyst is only of the middle range level among the state-of-the-art precious-metal-based catalysts, due to the much lower cost of the BNNF-Cu catalyst, its cost efficiency is the highest among these catalysts. This work provides a choice of support material that can promote the development of single-atom catalysts.

Solution-Processed, Inverted AgBiS2 Nanocrystal Solar Cells

AgBiS₂ nanocrystals are a promising nontoxic alternative to PbS, CsPbI₃, and CdS quantum dots for solution-fabricated nanocrystal photovoltaics. In this work, we fabricated the first inverted (p-i-n) structure AgBiS₂ nanocrystal solar cells. We selected spray-coated NiO as the hole-transporting material and used PCBM/BCP as the electron-transporting material. Combining transient photocurrent and photovoltage measurements with femtosecond transient absorption spectroscopy, we investigated the charge collection process on metal oxide/AgBiS₂ interfaces and demonstrated that the NiO/AgBiS₂ NC junction in the p-i-n configuration is more efficient for charge carrier collection. The fabricated p-i-n solar cells exhibited a 4.3% power conversion efficiency (PCE), which was higher than that of conventional n-i-p solar cells fabricated using the same sample. Additionally, inverted devices showed an ultrahigh short-circuit current (J_SC) over 20.7 mA cm^-2 and 0.38 V open-circuit voltage (V_OC), suggesting their potential for further improvements in efficiency and, eventually, for large-scale production.

Quantum Dot Based Solar Cells: Role of Nanoarchitectures, Perovskite Quantum Dots, and Charge-Transporting Layers

Quantum dot solar cells (QDSCs) are attractive technology for commercialization, owing to various advantages, such as cost effectiveness, and require relatively simple device fabrication processes. The properties of semiconductor quantum dots (QDs), such as band gap energy, optical absorption, and carrier transport, can be effectively tuned by modulating their size and shape. Two types of architectures of QDSCs have been developed: 1) photoelectric cells (PECs) fabricated from QDs sensitized on nanostructured TiO₂ , and 2) photovoltaic cells fabricated from a Schottky junction and heterojunction. Different types of semiconductor QDs, such as a secondary, ternary, quaternary, and perovskite semiconductors, are used for the advancement of QDSCs. The major challenge in QDSCs is the presence of defects in QDs, which lead to recombination reactions and thereby limit the overall performance of the device. To tackle this problem, several strategies, such as the implementation of a passivation layer over the QD layer and the preparation of core-shell structures, have been developed. This review covers aspects of QDSCs that are essential to understand for further improvement in this field and their commercialization.

Graphene Oxide: From Tunable Structures to Diverse Luminescence Behaviors

Since the first discovery of luminescent graphene oxide (GO), exponentially increasing investigations on the tunable structures and surfaces for modulating its optical properties have struggled to expand applications in imaging, sensing, biomedical diagnostics, and so on. Here, the latest works on reconstructing or modifying the structures and surfaces of GO to achieve diverse luminescence are systematically reviewed, including fluorescence, electroluminescence, and chemiluminescence. Moreover, the fundamental difficulties of the investigations and applications of luminescent GO nanomaterials are clarified to inspire more constructive thoughts for expanding their application boundaries.

Near-Infrared Active Lead Chalcogenide Quantum Dots: Preparation, Post-Synthesis Ligand Exchange, and Applications in Solar Cells

Quantum dots (QDs) of lead chalcogenides (e.g. PbS, PbSe, and PbTe) are attractive near-infrared (NIR) active materials that show great potential in a wide range of applications, such as, photovoltaics (PV), optoelectronics, sensors, and bio-electronics. The surface ligand plays an essential role in the production of QDs, post-synthesis modification, and their integration to practical applications. Therefore, it is critically important that the influence of surface ligands on the synthesis and properties of QDs is well understood for their applications in various devices. In this Review we elaborate the application of colloidal synthesis techniques for the preparation of lead chalcogenide based QDs. We specifically focus on the influence of surface ligands on the synthesis of QDs and their solution-phase ligand exchange. Given the importance of lead chalcogenide QDs as potential light harvesters, we also pay particular attention to the current progress of these QDs in photovoltaic applications.

A thin CdSe shell boosts the electron transfer from CdTe quantum dots to methylene blue

CdTe core and CdTe/CdSe core/shell quantum dots (QD) are investigated with steady state and time-resolved spectroscopic methods. The coating of the CdTe core with a 0.7 nm thick CdSe shell shifts the lowest exciton absorption band to the red by more than 70 nm making the CdTe/CdSe QD an interesting candidate for application in solar energy conversion. Femtosecond transient absorption measurements are applied to study the photoinduced electron transfer (ET) to the molecular acceptor methylene blue (MB). ET times after single excitation of the QD are determined for different MB : QD ratios. The ET reaction is significantly faster in the case of the MB-CdTe/CdSe QD complexes, indicative of an altered charge distribution in the photoexcited heterostructure with a higher electron density in the CdSe shell. As a result of the efficient absorption of incoming light and the faster ET reaction, the amount of reduced MB in the time resolved experiments is higher for CdTe/CdSe QD compared to CdTe QD.

Semiconductor quantum dot-sensitized rainbow photocathode for effective photoelectrochemical hydrogen generation

The present study reports the fabrication of CdSe quantum dot (QD)-sensitized photocathodes on NiO-coated indium tin oxide (ITO) electrodes and their H₂-generating ability upon light irradiation. A well-established spin-coating method was used to deposit CdSe QD stock solution onto the surface of NiO/ITO electrodes, thereby leading to the construction of various CdSe QD-sensitized photocathodes. The present report includes the construction of rainbow photocathodes by spin-coating different-sized QDs in a sequentially layered manner, thereby creating an energetically favorable gradient for charge separation. The resulting rainbow photocathodes with forward energetic gradient for charge separation and subsequent electron transfer to a solution-based hydrogen-evolving catalyst (HEC) exhibit good light-harvesting ability and enhanced photoresponses compared with the reverse rainbow photocathodes under white LED light illumination. Under minimally optimized conditions, a photocurrent density of as high as 115 μA⋅cm^-2 and a Faradaic efficiency of 99.5% are achieved, which is among the most effective QD-based photocathode water-splitting systems.

Formation of uniform PbS quantum dots by a spin-assisted successive precipitation and anion exchange reaction process using PbX2 (X = Br, I) and Na2S precursors

We devised a straightforward spin-assisted successive precipitation and anion exchange reaction (spin-SPAER) process in order to deposit relatively uniform PbS quantum dots (QDs) on mesoporous TiO₂ (mp-TiO₂).

Secondary coordination sphere accelerates hole transfer for enhanced hydrogen photogeneration from [FeFe]-hydrogenase mimic and CdSe QDs in water

Achieving highly efficient hydrogen (H₂) evolution via artificial photosynthesis is a great ambition pursued by scientists in recent decades because H₂ has high specific enthalpy of combustion and benign combustion product. [FeFe]-Hydrogenase ([FeFe]-H₂ase) mimics have been demonstrated to be promising catalysts for H₂ photoproduction. However, the efficient photocatalytic H₂ generation system, consisting of PAA-g-Fe₂S₂, CdSe QDs and H₂A, suffered from low stability, probably due to the hole accumulation induced photooxidation of CdSe QDs and the subsequent crash of [FeFe]-H₂ase mimics. In this work, we take advantage of supramolecular interaction for the first time to construct the secondary coordination sphere of electron donors (HA⁻) to CdSe QDs. The generated secondary coordination sphere helps realize much faster hole removal with a ~30-fold increase, thus leading to higher stability and activity for H₂ evolution. The unique photocatalytic H₂ evolution system features a great increase of turnover number to 83600, which is the highest one obtained so far for photocatalytic H₂ production by using [FeFe]-H₂ase mimics as catalysts.

Improving the Photocurrent in Quantum-Dot-Sensitized Solar Cells by Employing Alloy PbxCd1-xS Quantum Dots as Photosensitizers

Ternary alloy Pb_xCd_1−xS quantum dots (QDs) were explored as photosensitizers for quantum-dot-sensitized solar cells (QDSCs). Alloy Pb_xCd_1−xS QDs (Pb_0.54Cd_0.46S, Pb_0.31Cd_0.69S, and Pb_0.24Cd_0.76S) were found to substantially improve the photocurrent of the solar cells compared to the single CdS or PbS QDs. Moreover, it was found that the photocurrent increases and the photovoltage decreases when the ratio of Pb in Pb_xCd_1−xS is increased. Without surface protecting layer deposition, the highest short-circuit current density reaches 20 mA/cm² under simulated AM 1.5 illumination (100 mW/cm²). After an additional CdS coating layer was deposited onto the Pb_xCd_1−xS electrode, the photovoltaic performance further improved, with a photocurrent of 22.6 mA/cm² and an efficiency of 3.2%.

Electrophoretic Deposition of Carbon Nitride Layers for Photoelectrochemical Applications

Electrophoretic deposition (EPD) is used for the growth of carbon nitride (C3N4) layers on conductive substrates. EPD is fast, environmentally friendly, and allows the deposition of negatively charged C3N4 with different compositions and chemical properties. In this method, C3N4 can be deposited on various conductive substrates ranging from conductive glass and carbon paper to nickel foam possessing complex 3D geometries. The high flexibility of this approach enables us to readily tune the photophysical and photoelectronic properties of the C3N4 electrodes. The advantage of this method was further illustrated by the tailored construction of a heterostructure between two complementary C3N4, with marked photoelectrochemical activity.

Optimizing CdS intermediate layer of CdS/CdSe quantum dot-sensitized solar cells to increase light harvesting ability and improve charge separation efficiency

A modified Successive Ionic Layer Adsorption and Reaction (SILAR) technique with the addition of a triethanolamine (TEA) additive into a cationic precursor solution was utilized to optimize the CdS intermediate layer to enhance the performance.

Improved Photoelectrochemical Cell Performance of Tin Oxide with Functionalized Multiwalled Carbon Nanotubes-Cadmium Selenide Sensitizer

Here we report functionalized multiwalled carbon nanotubes (f-MWCNTs)-CdSe nanocrystals (NCs) as photosensitizer in photoelectrochemical cells, where f-MWCNTs were uniformly coated with CdSe NCs onto SnO2 upright standing nanosheets by using a simple electrodeposition method. The resultant blended photoanodes demonstrate extraordinary electrochemical properties including higher Stern-Volmer constant, higher absorbance, and positive quenching, etc., caused by more accessibility of CdSe NCs compared with pristine SnO2-CdSe photoanode. Atomic and weight percent changes of carbon with f-MWCNTs blending concentrations were confirmed from the energy dispersive X-ray analysis. The morphology images show a uniform coverage of CdSe NCs over f-MWCNTs forming a core-shell type structure as a blend. Compared to pristine CdSe, photoanode with f-MWCNTs demonstrated a 257% increase in overall power conversion efficiency. Obtained results were corroborated by the electrochemical impedance analysis. Higher scattering, more accessibility, and hierarchical structure of SnO2-f-MWCNTs-blend-CdSe NCs photoanode is responsible for higher (a) electron mobility (6.89 × 10(-4) to 10.89 × 10(-4) cm(2) V(-1) S(1-)), (b) diffusion length (27 × 10(-6)),

The effect of TiO2 nanoflowers as a compact layer for CdS quantum-dot sensitized solar cells with improved performance

Currently, TiO2 on a fluorine-doped tin oxide substrate is the most commonly used type of photoelectrode in high-efficiency quantum dot-sensitized solar cells (QDSSCs). The power conversion efficiency (PCE) of TiO2 photoelectrodes is limited because of higher charge recombination and lower QD loading on the TiO2 film. This article describes the effect of a TiO2 compact layer on a TiO2 film to enhance the performance of QDSSCs. TiO2 nanoparticles were coated on an FTO substrate by the doctor-blade method and then the TiO2 compact layer was successfully fabricated on the surface of the nanoparticles by a simple hydrothermal method. QDSSCs were made using these films as photoelectrodes with NiS counter electrodes. Under one sun illumination (AM 1.5 G, 100 mW cm(-2)), the QDSSCs showed PCEs of 2.19 and 2.93% for TCL1 and TCL2 based photoelectrodes, which are higher than the 1.33% value obtained with bare TiO2. The compact-layer-coated film electrodes provide a lower charge-transfer resistance and higher light harvesting. The compact layer on the TiO2 film is a more efficient photocatalyst than pure TiO2 film and physically separates the injected electrons in the TiO2 from the positively charged CdS QD/electrolyte.

Capping Ligand-Induced Self-Assembly for Quantum Dot Sensitized Solar Cells

Quantum dot-sensitized solar cells (QDSCs), having the advantages of low-cost assembling process, economically viable materials and intrinsic optoelectronic properties of QD sensitizers, are regarded as attractive candidates for the third-generation solar cells. In spite of the previous unsatisfied performance resulted from poor sensitization, an increasing power conversion efficiency has been experimentally confirmed with the development of effective deposition approaches in the last five years. In this Perspective article, we present an overview on versatile QD deposition methods, regarding mainly the effective loading of QDs and surface chemistry issues. Linker-assisted assembly, a most efficient sensitizer deposition approach to achieve fast, uniform and dense coverage of the sensitizers on mesoporous TiO2 film electrode, will be discussed with emphasis. Recent advances based on this deposition technique in achieving high efficiency are presented. Also, combined efforts regarding the overall improvement of the device have been discussed to provide more possible access to higher power conversion efficiencies of the QDSCs.

Silicon phthalocyanine covalently functionalized N-doped ultrasmall reduced graphene oxide decorated with Pt nanoparticles for hydrogen evolution from water

To improve the photocatalytic activity of graphene-based catalysts, silicon phthalocyanine (SiPc) covalently functionalized N-doped ultrasmall reduced graphene oxide (N-usRGO) has been synthesized through 1,3-dipolar cycloaddition of azomethine ylides. The obtained product (N-usRGO/SiPc) was characterized by transmission electron microscopy, atomic force microscopy, Fourier transform infrared spectroscopy, Raman spectra, X-ray photoelectron spectroscopy, fluorescence, and UV-vis spectroscopy. The results demonstrate that SiPc has been successfully grafted on the surface of N-usRGO. The N-usRGO/SiPc nanocomposite exhibits high light-harvesting efficiency covering a range of wavelengths from the ultraviolet to visible light. The efficient fluorescence quenching and the enhanced photocurrent response confirm that the photoinduced electron transfers from the SiPc moiety to the N-usRGO sheet. Moreover, we chose Pt nanoparticles as cocatalyst to load on N-usRGO/SiPc sheets to obtain the optimal H2 production effect. The platinized N-usRGO/SiPc (N-usRGO/SiPc/Pt) demonstrates good hydrogen evolution performance under both UV-vis and visible light (λ>400 nm) irradiation. The apparent quantum yields are 1.3% and 0.56% at 365 and 420 nm, respectively. These results reveal that N-usRGO/SiPc/Pt nanocomposite, consolidating the advantages of SiPc, N-usRGO, and Pt NPs, can be a potential candidate for hydrogen evolution from water under UV-vis or visible light irradiation.

Efficiency enhanced rutile TiO2 nanowire solar cells based on an Sb2S3 absorber and a CuI hole conductor

The spray technique is introduced for CuI deposition on Sb₂S₃-sensitized TiO₂ nanowire solar cells, which enhances the photovoltaic performance of the device.

Incorporation of carbon nanotubes in a hierarchical porous photoanode of tandem quantum dot sensitized solar cells

The incorporation of multi-walled carbon nanotubes (MWCNT) in quantum dot (QD) sensitized solar cells (QDSC) based on CdSe QDs and quantum rods (QRs) is investigated. The composite hierarchical porous photoanode of titania/CNT is synthesized by sol-gel induced phase separation and QDs/QRs are prepared by the modified solvothermal method. The QDs and QRs form a tandem structure on the hierarchical porous photoanode after deposition by the electrophoretic method. Incorporation of MWCNT in the QDSC photoanode in optimum content (0.32 wt%) causes appreciable enhancement in cells efficiency (about 41% increase). This improvement in efficiency mainly emerges from the beneficial role of MWCNTs in charge injection and collection. The MWCNTs result in longer electron lifetime and higher electron diffusion length, which is confirmed by electrochemical impedance spectroscopy.

Comparative experiments of graphene covalently and physically binding CdSe quantum dots to enhance the electron transport in flexible photovoltaic devices

In this research, we prepared composite films via covalent coupling of CdSe quantum dots (QDs) to graphene through the direct binding of aryl radicals to the graphene surface. To compare the carrier transport with the CdSe aryl binding graphene film, we prepared CdSe pyridine capping graphene films through the pi-pi interactions of noncovalent bonds between the graphene and pyridine molecules. The photovoltaic devices were fabricated from the two hybrid films using the electrophoretic deposition method on flexible substrates. Even though the two hybrid films have the same amount of QDs and graphene, time-resolved fluorescence emission decay results show that the emission lifetime of the CdSe aryl group binding graphene film is significantly shorter than that of the pyridine capping CdSe-graphene. The quantum efficiency and photocurrent density of the device fabricated from CdSe aryl binding graphene were also higher than those of the device fabricated from pyridine capping CdSe-graphene. These results indicated that the carrier transport of the QD-graphene system is not related to the additive effect from the CdSe and graphene components but rather is a result of the unique interactions between the graphene and QDs. We could expect that these results can be useful in designing QD-graphene composite materials, which are applied in photovoltaic devices.

Integrated graphene/nanoparticle hybrids for biological and electronic applications

The development of novel graphene/nanoparticle hybrid materials is currently the subject of tremendous research interest. The intrinsic exceptional assets of both graphene (including graphene oxide and reduced graphene oxide) and nanoparticles render their hybrid materials synergic properties that can be useful in various applications. In this feature review, we highlight recent developments in graphene/nanoparticle hybrids and their promising potential in electronic and biological applications. First, the latest advances in synthetic methods for the preparation of the graphene/nanoparticle hybrids are introduced, with the emphasis on approaches to (1) decorate nanoparticles onto two-dimensional graphene and (2) wrap nanoparticles with graphene sheets. The pros and cons of large-scale synthesis are also discussed. Then, the state-of-the-art of graphene/nanoparticle hybrids in electronic and biological applications is reviewed. For electronic applications, we focus on the advantages of using these hybrids in transparent conducting films, as well as energy harvesting and storage. Biological applications, electrochemical biosensing, bioimaging, and drug delivery using the hybrids are showcased. Finally, the future research prospects and challenges in this rapidly developing area are discussed.

Controllable synthesis of ultrasmall CuInSe2 quantum dots for photovoltaic application

Ultrasmall CuInSe₂ quantum dots were synthesized by a facile solvothermal method and used as a sensitizer in CdS/CuInSe₂ quantum dot solar cells to improve the photovoltaic performance.

Synthesis of eco-friendly CuInS2 quantum dot-sensitized solar cells by a combined ex situ/in situ growth approach

A cadmium-free CuInS2 quantum dot (QD)-sensitized solar cell (QDSC) has been fabricated by taking advantage of the ex situ synthesis approach for fabricating highly crystalline QDs and the in situ successive ionic-layer adsorption and reaction (SILAR) approach for achieving high surface coverage of QDs. The ex situ synthesized CuInS2 QDs can be rendered water soluble through a simple and rapid two-step method under the assistance of ultrasonication. This approach allows a stepwise ligand change from the insertion of a foreign ligand to ligand replacement, which preserves the long-term stability of colloidal solutions for more than 1 month. Furthermore, the resulting QDs can be utilized as sensitizers in QDSCs, and such a QDSC can deliver a power conversion efficiency (PCE) of 0.64%. Using the SILAR process, in situ CuInS2 QDs could be preferentially grown epitaxially on the pre-existing seeds of ex situ synthesized CuInS2 QDs. The results indicated that the CuInS2 QDSC fabricated by the combined ex situ/in situ growth process exhibited a PCE of 1.84% (short-circuit current density = 7.72 mA cm(-2), open-circuit voltage = 570 mV, and fill factor = 41.8%), which is higher than the PCEs of CuInS2 QDSCs fabricated by ex situ and in situ growth processes, respectively. The relative efficiencies of electrons injected by the combined ex situ/in situ growth approach were higher than those of ex situ synthesized CuInS2 QDs deposited on TiO2 films, as determined by emission-decay kinetic measurements. The incident photon-to-current conversion efficiency has been determined, and electrochemical impedance spectroscopy has been carried out to investigate the photovoltaic behavior and charge-transfer resistance of the QDSCs. The results suggest that the combined synergetic effects of in situ and ex situ CuInS2 QD growth facilitate more electron injection from the QD sensitizers into TiO2.

Carbon nanomaterials for electronics, optoelectronics, photovoltaics, and sensing

In the last three decades, zero-dimensional, one-dimensional, and two-dimensional carbon nanomaterials (i.e., fullerenes, carbon nanotubes, and graphene, respectively) have attracted significant attention from the scientific community due to their unique electronic, optical, thermal, mechanical, and chemical properties. While early work showed that these properties could enable high performance in selected applications, issues surrounding structural inhomogeneity and imprecise assembly have impeded robust and reliable implementation of carbon nanomaterials in widespread technologies. However, with recent advances in synthesis, sorting, and assembly techniques, carbon nanomaterials are experiencing renewed interest as the basis of numerous scalable technologies. Here, we present an extensive review of carbon nanomaterials in electronic, optoelectronic, photovoltaic, and sensing devices with a particular focus on the latest examples based on the highest purity samples. Specific attention is devoted to each class of carbon nanomaterial, thereby allowing comparative analysis of the suitability of fullerenes, carbon nanotubes, and graphene for each application area. In this manner, this article will provide guidance to future application developers and also articulate the remaining research challenges confronting this field.

Photovoltaic property of a vertically aligned carbon nanotube hexagonal network assembled with CdS quantum dots

A vertically aligned carbon nanotube (VACNT) hexagonal network was fabricated by plasma enhanced chemical vapor deposition as an electrode scaffold to assemble CdS quantum dots (QDs). The quantum dot sensitized solar cell (QDSSC) based on a VACNT/CdS hexagonal network shows a short circuit current density of 4.7 mA/cm(2), which is almost twice of that based on screen-printed CNT/CdS thin film with the same thickness. The enhancement of the short circuit current could be attributed to the unique morphology of the VACNT hexagonal network, which provides direct and percolating pathways for the electrons to transfer, enhances the spectral transmission through the hexagonal microchannels to the photoactive QD sites, and also presents more surface area to assembled CdS QDs without consuming extra substrate space. The photovoltaic property of the VACNT/CdS hexagonal network indicates its potential application in the energy conversion devices.

Building high-efficiency CdS/CdSe-sensitized solar cells with a hierarchically branched double-layer architecture

We report a double-layer architecture for a photoanode of quantum-dot-sensitized solar cells (QDSSCs), which consists of a ZnO nanorod array (NR) underlayer and a ZnO nanotetrapod (TP) top layer. Such double-layer and branching strategies have significantly increased the power conversion efficiency (PCE) to as high as 5.24%, nearly reaching the record PCE of QDSSCs based on TiO2. Our systematic studies have shown that the double-layer strategy could significantly reduce charge recombination at the interface between the charge collection anode (FTO) and ZnO nanostructure because of the strong and compact adhesion of the NRs and enhance charge transport due to the partially interpenetrating contact between the NR and TP layers, leading to improved open-circuit voltage (Voc) and short-circuit current density (Jsc). Also, when the double layer was subjected to further branching, a large increase in Jsc and, to a lesser extent, the fill factor (FF) has resulted from increases in quantum-dot loading, enhanced light scattering, and reduced series resistance.

Quantum Dot Solar Cells. The Next Big Thing in Photovoltaics

The recent surge in the utilization of semiconductor nanostructures for solar energy conversion has led to the development of high-efficiency solar cells. Some of these recent advances are in the areas of synthesis of new semiconductor materials and the ability to tune the electronic properties through size, shape, and composition and to assemble quantum dots as hybrid assemblies. In addition, processes such as hot electron injection, multiple exciton generation (MEG), plasmonic effects, and energy-transfer-coupled electron transfer are gaining momentum to overcome the efficiency limitations of energy capture and conversion. The recent advances as well as future prospects of quantum dot solar cells discussed in this perspective provide the basis for consideration as "The Next Big Thing" in photovoltaics.

Quantum-dot-sensitized solar cell with unprecedentedly high photocurrent

The reported photocurrent density (J_SC) of PbS quantum dot (QD)-sensitized solar cell was less than 19 mA/cm² despite the capability to generate 38 mA/cm², which results from inefficient electron injection and fast charge recombination. Here, we report on a PbS:Hg QD-sensitized solar cell with an unprecedentedly high J_SC of 30 mA/cm². By Hg²⁺ doping into PbS, J_SC is almost doubled with improved stability. Femtosecond transient study confirms that the improved J_SC is due to enhanced electron injection and suppressed charge recombination. EXAFS reveals that Pb-S bond is reinforced and structural disorder is reduced by interstitially incorporated Hg²⁺, which is responsible for the enhanced electron injection, suppressed recombination and stability. Thanks to the extremely high J_SC, power conversion efficiency of 5.6% is demonstrated at one sun illumination.