Influence of Molecular Shape on Solid-State Packing in Disordered PC61BM and PC71BM Fullerenes

Naphthalocyanine-Based NIR Organic Photodiode: Understanding the Role of Different Types of Fullerenes

In this work, we presented experimental observation on solution-processed bulk heterojunction organic photodiode using vanadyl 2,11,20,29-tetra tert-butyl 2,3 naphthalocyanine (VTTBNc) as a p-type material. VTTBNc is blended with two different acceptors, which are PC₆₁BM and PC₇₁BM, to offer further understanding in evaluating the performance in organic photodiode (OPD). The blend film of VTTBNc:PC₇₁BM with a volumetric ratio of 1:1 exhibits optimized performance in the VTTBNc blend structure with 2.31 × 10⁹ Jones detectivity and 26.11 mA/W responsivity at a −1 V bias. The response and recovery time of VTTBNc:PC₇₁BM were recorded as 241 ms and 310 ms, respectively. The light absorption measurement demonstrated that VTTBNc could extend the light absorption to the near-infrared (NIR) region. The detail of the enhancement of the performance by adding VTTBNc to the blend was further explained in the discussion section.

Fullerene as an additive for increasing the efficiency of organic solar cells to more than 17

In this work, we introduced a fullerene acceptor (PC₇₁BM) into the binary photo-active layer based on a polymer donor (PM6) and a non-fullerene small molecular acceptor (BTP-BO-4Cl), and as a consequence, the ternary organic solar cells realized a high-power conversion efficiency of 17.39% compared to 16.65% in binary solar cells. The performance enhancement was found to be due to the optimized morphology and hence balanced hole and electron mobilities, which is responsible for the suppressed charge recombination and hence high photocurrent in solar cells. In addition, PC₇₁BM shows the complementary absorption with PM6 and BTP-BO-4Cl, which can broaden the absorption range of the photo-active layer and hence more photons from the sunlight can be utilized. Besides, PC₇₁BM shows the cascade energy level alignment between PM6 and BTP-BO-4Cl, which is helpful for charge transfer from donor to acceptor. All these merits explain the high performance in ternary solar cells, and also demonstrate that ternary photovoltaics adopting non-fullerene acceptor with the fullerene acceptor as small amount of additive is an efficient strategy to gain high performing organic solar cells.

New Insights into the Quantitative Relationship between Surface Chemistry of Fullerene (C60) and Solubility Parameters and Compatibility with Polymers

The quantitative relationship between the surface chemistry of carbon materials and the compatibility with polymers is a fundamental and vital physical chemistry problem in the field of polymer nanocomposites. Traditional experimental methods are difficult to solve this problem, so no theory has been formed to guide the functionalization of carbon materials. In this work, the quantitative relationship between functional groups and Hildebrand (δ_T) and transformed Hansen (δ_vdW and δ_ele) solubility parameters of fullerene (C60) was determined by molecular dynamics simulation. Besides, which solubility parameter can more accurately predict the compatibility between C60 and three typical polymers with different polarity as a function of grafting ratio is investigated. Very interestingly, no matter which group is grafted, δ_T and δ_vdW of C60 show a slight increase first and then a decrease with the grafting ratio, whereas δ_ele first increases abruptly and then decreases slightly. The introduction of polar groups (-OH, -COOH, and -NH₂) is conducive to improving the compatibility between C60 and polymers, whereas the introduction of the nonpolar group (-CH₃) is not. In terms of predicting compatibility, the Hildebrand solubility parameter is better than the Hansen solubility parameter due to the nonpolar nature of the polymers, even for nitrile butadiene rubber. Finally, the optimum grafting ratios corresponding to the maximum binding energies of C60/polymers mixtures were obtained. This study provides a new understanding of the functionalization of C60 at the molecular level and promotes the development of the theory of the thermodynamics of mixing.

Genome-Wide Identification and Analysis of CC-NBS-LRR Family in Response to Downy Mildew and Black Rot in Chinese Cabbage

The nucleotide-binding site-leucine-rich repeat (NBS-LRR) gene family is the largest group of plant disease resistance (R) genes widespread in response to viruses, bacteria, and fungi usually involved in effector triggered immunity (ETI). Forty members of the Chinese cabbage CC type NBS-LRR family were investigated in this study. Gene and protein characteristics, such as distributed locations on chromosomes and gene structures, were explored through comprehensive analysis. CC-NBS-LRR proteins were classified according to their conserved domains, and the phylogenetic relationships of CC-NBS-LRR proteins in Brassica rapa, Arabidopsis thaliana, and Oryza sativa were compared. Moreover, the roles of BrCC-NBS-LRR genes involved in pathogenesis-related defense were studied and analyzed. First, the expression profiles of BrCC-NBS-LRR genes were detected by inoculating with downy mildew and black rot pathogens. Second, sensitive and resistant Chinese cabbage inbred lines were screened by downy mildew and black rot. Finally, the differential expression levels of BrCC-NBS-LRR genes were monitored at 0, 1, 3, 6, 12 and 24 h for short and 0, 3, 5, 7, 10 and 14 days for long inoculation time. Our study provides information on BrCC-NBS-LRR genes for the investigation of the functions and mechanisms of CC-NBS-LRR genes in Chinese cabbage.

Thiophene- and Carbazole-Substituted N-Methyl-Fulleropyrrolidine Acceptors in PffBT4T-2OD Based Solar Cells

The impact of fullerene side chain functionalization with thiophene and carbazole groups on the device properties of bulk-heterojunction polymer:fullerene solar cells is discussed through a systematic investigation of material blends consisting of the conjugated polymer poly[(5,6-difluoro-2,1,3-benzothiadiazol-4,7-diyl)-alt-(3,3‴-di(2-octyldodecyl)-2,2';5',2″;5″,2‴-quaterthiophen-5,5‴-diyl)] (PffBT4T-2OD) as donor and C60 or C70 fulleropyrrolidines as acceptors. The photovoltaic performance clearly depended on the molecular structure of the fulleropyrrolidine substituents although no direct correlation with the surface morphology of the photoactive layer, as determined by atomic force microscopy, could be established. Although some fulleropyrrolidines possess favorable lowest unoccupied molecular orbital levels, when compared to the standard PC71BM, they originated OPV cells with inferior efficiencies than PC71BM-based reference cells. Fulleropyrrolidines based on C60 produced, in general, better devices than those based on C70, and we attribute this observation to the detrimental effect of the structural and energetic disorder that is present in the regioisomer mixtures of C70-based fullerenes, but absent in the C60-based fullerenes. These results provide new additional knowledge on the effect of the fullerene functionalization on the efficiency of organic solar cells.

Different agglomeration properties of PC61BM and PC71BM in photovoltaic inks – a spin-echo SANS study

Fullerene derivatives are used in a wide range of applications including as electron acceptors in solution-processable organic photovoltaics.

PffBT4T-2OD Based Solar Cells with Aryl-Substituted N-Methyl-Fulleropyrrolidine Acceptors

Novel C60 and C70 N-methyl-fulleropyrrolidine derivatives, containing both electron withdrawing and electron donating substituent groups, were synthesized by the well-known Prato reaction. The corresponding highest occupied molecular orbital (HOMO)/lowest unoccupied molecular orbital (LUMO) energy levels were determined by cyclic voltammetry, from the onset oxidation and reduction potentials, respectively. Some of the novel fullerenes have higher LUMO levels than the standards PC61BM and PC71BM. When tested in PffBT4T-2OD based polymer solar cells, with the standard architecture ITO/PEDOT:PSS/Active-Layer/Ca/Al, these fullerenes do not bring about any efficiency improvements compared to the standard PC71BM system, however they show how the electronic nature of the different substituents strongly affects the efficiency of the corresponding organic photovoltaic (OPV) devices. The functionalization of C70 yields a mixture of regioisomers and density functional theory (DFT) calculations show that these have systematically different electronic properties. This electronic inhomogeneity is likely responsible for the lower performance observed in devices containing C70 derivatives. These results help to understand how new fullerene acceptors can affect the performance of OPV devices.

Amine-Based Interfacial Engineering in Solution-Processed Organic and Perovskite Solar Cells

Solution-processed organic solar cells (OSCs) and hybrid perovskite solar cells (PvSCs) generally require appropriate transparent electrode with a low work function, which improves the electron extraction, increases the built-in potential, and suppresses charge recombinations. Hence, interfacial modifiers between the cathode and the photoactive layer play a significant role in OSCs and PvSCs, as they provide suitable energy-level alignment, leading to desirable charge carrier selectivity and suppressing charge carrier recombinations at the interfaces. Here, we present a comprehensive study of the energy-level mapping between a transparent electrode and photoactive layers to enhance the electron-transport ability by introducing amine-based interfacial modifiers (ABIMs). Among the ABIMs, polyethylenimine ethoxylated (PEIE) incorporating inverted OSCs shows enhanced power conversion efficiencies (PCEs) from 0.32 to 9.83% due to large interfacial dipole moments, leading to a well-aligned energy level between the cathode and the photoactive layer. Furthermore, we explore the versatility of the PEIE ABIM by employing different photoactive layers with fullerene derivatives, a nonfullerene acceptor, and a perovskite layer. Promisingly, inverted nonfullerene OSCs and planar n-i-p PvSCs with PEIE ABIM show outstanding PCEs of 11.88 and 17.15%, respectively.

Deconstructing the behavior of donor–acceptor copolymers in solution & the melt: the case of PTB7

Molecular dynamics simulations of the donor–acceptor copolymer PTB7 at near experimental scale reveal structure–dynamics correlations in the condensed phase.

Recent Developments in the Optimization of the Bulk Heterojunction Morphology of Polymer: Fullerene Solar Cells

Organic photovoltaic (OPV) devices, made with semiconducting polymers, have recently attained a power conversion efficiency (PCE) over 14% in single junction cells and over 17% in tandem cells. These high performances, together with the suitability of the technology to inexpensive large-scale manufacture, over lightweight and flexible plastic substrates using roll-to-roll (R2R) processing, place the technology amongst the most promising for future harvesting of solar energy. Although OPVs using non-fullerene acceptors have recently outperformed their fullerene-based counterparts, the research in the development of new fullerenes and in the improvement of the bulk-heterojunction (BHJ) morphology and device efficiency of polymer:fullerene solar cells remains very active. In this review article, the most relevant research works performed over the last 3 years, that is, since the year 2016 onwards, in the field of fullerene-based polymer solar cells based on the copolymers PTB7, PTB7-Th (also known as PBDTTT-EFT) and PffBT4T-2OD, are presented and discussed. This review is primarily focused on studies that involve the improvement of the BHJ morphology, efficiency and stability of small active area devices (typically < 15 mm²), through the use of different processing strategies such as the use of different fullerene acceptors, different processing solvents and additives and different thermal treatments.

Structural Correlations and Percolation in Twisted Perylene Diimides Using a Simple Anisotropic Coarse-Grained Model

Large, twisted, and fused conjugated molecular architectures have begun to appear more prominently in the organic semiconductor literature. From a modeling perspective, such structures present a challenge to conventional simulation techniques; atomistic resolutions are computationally inefficient, while traditional isotropic coarse-grained models do not capture the inherent anisotropies of the molecules. In this work, we develop a simple coarse-grained model that explicitly incorporates the anisotropy of these molecular architectures, thereby providing a route toward analyzing π-stacking, and thus qualitative electronic structure, at a computationally efficient coarse-grained resolution. Our simple coarse-grained model maintains relative orientations of conjugated rings, as well as inter-ring dihedrals, that are critical for understanding electronic and excitonic transport in bulk systems. We apply this model to understand structural correlations in several recently synthesized perylene diimide (PDI)-based organic semiconductors. Twisted and nonplanar molecular architectures are found to promote amorphous morphologies while maintaining local π-stacking. A graph theoretical network analysis demonstrates that these twisted molecules are more likely to form percolating three-dimensional pathways for charge motion than strictly planar molecules, which show connectivity in only one dimension.

Closely packed, low reorganization energy π-extended postfullerene acceptors for efficient polymer solar cells

New organic semiconductors are essential for developing inexpensive, high-efficiency, solution-processable polymer solar cells (PSCs). PSC photoactive layers are typically fabricated by film-casting a donor polymer and a fullerene acceptor blend, with ensuing solvent evaporation and phase separation creating discrete conduits for photogenerated holes and electrons. Until recently, n-type fullerene acceptors dominated the PSC literature; however, indacenodithienothiophene (IDTT)-based acceptors have recently enabled remarkable PSC performance metrics, for reasons that are not entirely obvious. We report two isomeric IDTT-based acceptors 3,9-bis(2-methylene-(3-(1,1-dicyanomethylene)-benz-(5, 6)indanone))-5,5,11,11-tetrakis(4-nonylphenyl)-dithieno[2,3-d:2',3'-d']-s-indaceno[1,2-b:5,6-b']di-thiophene (ITN-C9) and 3,9-bis(2-methylene-(3-(1,1-dicyanomethylene)-benz(6,7)indanone))-5,5,11,11-tetrakis(4-nonylphenyl)-dithieno[2,3-d:2',3'-d']-s-indaceno[1,2-b:5,6-b']dithiophene (ITzN-C9) that shed light on the exceptional IDTT properties vis-à-vis fullerenes. The neat acceptors and blends with fluoropolymer donor poly{[4,8-bis[5-(2- ethylhexyl)-4-fluoro-2-thienyl]benzo[1,2-b:4,5-b']dithiophene2,6-diyl]-alt-[2,5-thiophenediyl[5,7-bis(2-ethylhexyl)-4,8-dioxo4H,8H-benzo[1,2-c:4,5-c']dithiophene-1,3-diyl]]} (PBDB-TF) are investigated by optical spectroscopy, cyclic voltammetry, thermogravimetric analysis, differential scanning calorimetry, single-crystal X-ray diffraction, photovoltaic response, space-charge-limited current transport, atomic force microscopy, grazing incidence wide-angle X-ray scattering, and density functional theory-level quantum chemical analysis. The data reveal that ITN-C9 and ITzN-C9 organize such that the lowest unoccupied molecular orbital-rich end groups have intermolecular π-π distances as close as 3.31(1) Å, with electronic coupling integrals as large as 38 meV, and internal reorganization energies as small as 0.133 eV, comparable to or superior to those in fullerenes. ITN-C9 and ITzN-C9 have broad solar-relevant optical absorption, and, when blended with PBDB-TF, afford devices with power conversion efficiencies near 10%. Performance differences between ITN-C9 and ITzN-C9 are understandable in terms of molecular and electronic structure distinctions via the influences on molecular packing and orientation with respect to the electrode.

Triptycene as a Supramolecular Additive in PTB7:PCBM Blends and Its Influence on Photovoltaic Properties

Additives play an important role in modifying the morphology and phase separation of donor and acceptor molecules in bulk heterojunction (BHJ) solar cells. Here, we report triptycene (TPC) as a small-molecule additive for supramolecular control of phase separation and concomitant improvement of the power conversion efficiency (PCE) of PTB7 donor and fullerene acceptor-based BHJ polymer solar cells. An overall 60% improvement in PCE is observed for both PTB7:PC₆₁BM and PTB7:PC₇₁BM blends. The improved photovoltaic (PV) performance can be attributed to three factors: (a) TPC-induced supramolecular interactions with donor:acceptor components in the blends to realize a nanoscale phase-separated morphology; (b) an increase in the charge transfer state energy that lowers the driving force for electron transfer from donor to acceptor molecules; and (c) an increase in the charge carrier mobility. An improvement in efficiency using TPC as a supramolecular additive has also been demonstrated for other BHJ blends such as PBDB-T:PC₇₁BM and P3HT:PCBM, implying the wide applicability of this new additive molecule. A comparison of the photostability of TPC as an additive for PTB7:PCBM solar cells to that of the widely used 1,8-diiodooctane additive shows ∼30% higher retention of PV performance for the TPC-added solar cells after 34 h of AM 1.5G illumination. The results obtained suggest that the approach of using additives that can promote supramolecular interactions to modify the length scale of phase separation between donor and acceptor is very promising and can lead to the development of highly efficient and stable organic photovoltaics.

Embedding a Diketopyrrolopyrrole-Based Cross-linking Interfacial Layer Enhances the Performance of Organic Photovoltaics

In this study, we prepared DPPBTDA, a diketopyrrolopyrrole-based small molecule presenting a terminal cross-linkable azido group, as a cathode modifying layer for organic photovoltaics (OPVs) having the inverted device structure glass/indium tin oxide/zinc oxide (ZnO) with or without the interfacial layer (IFL)/active layer/MoO₃/Ag. The active layer comprising a blend of poly[4,8-bis(5-(2-ethylhexyl)thien-2-yl)benzo[1,2- b;4,5- b']dithiophene-2,6-diyl- alt-(4-(2-ethylhexyl)-3-fluorothieno[3,4- b]thiophene)-2-carboxylate-2,6-diyl] (PTB7-Th) as the electron donor and [6,6]-phenyl-C₇₁-butyric acid methyl ester (PC₇₁BM) as the electron acceptor. Atomic force microscopy, space-charge-limited current mobility, surface energy, electron spectroscopy for chemical analysis depth profile, ultraviolet photoelectron spectroscopy analysis, and OPV performance data revealed that the surface status of ZnO changed after inserting the DPPBTDA/PCBM hybrid IFL and induced an optimized blend morphology, having a preferred gradient distribution of the conjugated polymer and PC₇₁BM, for efficient carrier transport. The power conversion efficiency (AM 1.5 G, 1000 W m^-2) of the device incorporating the hybrid IFL increased to 9.4 ± 0.11% from 8.5 ± 0.15% for the preoptimized PTB7-Th/PCBM device (primarily because of an enhancement in the fill factor from 68.7 ± 1.1 to 72.1 ± 0.8%).

Planarity and multiple components promote organic photovoltaic efficiency by improving electronic transport

Establishing how the conformation of organic photovoltaic (OPV) polymers affects their electronic and transport properties is critical in order to determine design rules for new OPV materials and in particular to understand the performance enhancements recently reported for ternary blends. We report coupled classical and ab initio molecular dynamics simulations showing that polymer linkage twisting significantly reduces optical absorption efficiency, as well as hole transport rates in donor polymers. We predict that blends with components favoring planar geometries contribute to the enhancement of the overall efficiency of ternary OPVs. Furthermore, our electronic structure calculations for the PTB7-PID2-PC71BM system show that hole transfer rates are enhanced in ternary blends with respect to their binary counterpart. Finally, our results point at thermal disorder in the blend as a key reason responsible for device voltage losses and at the need to carry out electronic structure calculations at finite temperature to reliably compare with experiments.

Structural engineering of porphyrin-based small molecules as donors for efficient organic solar cells

Porphyrin-based small molecules as donors have long been ignored in bulky heterojunction organic solar cells due to their unfavorable aggregation and the low charge mobility. With the aim of striking a delicate balance between molecular design, morphology, interfacial layer and device fabrication to maximize the power conversion efficiency (PCE) of organic solar cells, three comparable porphyrin-based small molecules with an acceptor-donor-acceptor configuration have been developed for use as donor materials in solution processed small molecule bulk heterojunction organic solar cells. In these molecules, electron-deficient 3-ethylrhodanine is introduced into the electron-rich porphyrin core through 5,15-bis(phenylethynyl) linkers. Structural engineering with 10,20-bis(2-hexylnonyl) aliphatic peripheral substituent on the porphyrin core, instead of the aromatic substituents such as 10,20-bis[3,5-di(dodecyloxyl)phenyl], and 10,20-bis(4-dodecyloxylphenyl), can simultaneously facilitate stronger intermolecular π-π stacking and higher charge transfer mobility in the film, leading to a maximum PCE of 7.70% in a conventional device. The inverted devices have also been demonstrated to have long-term ambient stability and a comparable PCE of 7.55%.

Static and Dynamic Energetic Disorders in the C60, PC61BM, C70, and PC71BM Fullerenes

We use a combination of molecular dynamics simulations and density functional theory calculations to investigate the energetic disorder in fullerene systems. We show that the energetic disorder evaluated from an ensemble average contains contributions of both static origin (time-independent, due to loose packing) and dynamic origin (time-dependent, due to electron-vibration interactions). In order to differentiate between these two contributions, we compare the results obtained from an ensemble average approach with those derived from a time average approach. It is found that in both amorphous C60 and C70 bulk systems, the degrees of static and dynamic disorder are comparable, while in the amorphous PC61BM and PC71BM systems, static disorder is about twice as large as dynamic disorder.

Molecular-Scale Understanding of Cohesion and Fracture in P3HT:Fullerene Blends

Quantifying cohesion and understanding fracture phenomena in thin-film electronic devices are necessary for improved materials design and processing criteria. For organic photovoltaics (OPVs), the cohesion of the photoactive layer portends its mechanical flexibility, reliability, and lifetime. Here, the molecular mechanism for the initiation of cohesive failure in bulk heterojunction (BHJ) OPV active layers derived from the semiconducting polymer poly(3-hexylthiophene) [P3HT] and two monosubstituted fullerenes is examined experimentally and through molecular-dynamics simulations. The results detail how, under identical conditions, cohesion significantly changes due to minor variations in the fullerene adduct functionality, an important materials consideration that needs to be taken into account across fields where soluble fullerene derivatives are used.

Stereochemistry of spiro-acetalized [60]fullerenes: how the exo and endo stereoisomers influence organic solar cell performance

Exploiting bis-addition products of fullerenes is a rational way to improve the efficiency of bulk heterojunction-type organic photovoltaic cells (OPV); however, this design inherently produces regio- and stereoisomers that may impair the ultimate performance and fabrication reproducibility. Here, we report unprecedented exo and endo stereoisomers of the spiro-acetalized [60]fullerene monoadduct with methyl- or phenyl-substituted 1,3-dioxane (SAF6). Although there is no chiral carbon in either the reagent or the fullerene, equatorial (eq) rather than axial (ax) isomers are selectively produced at an exo-eq:endo-eq ratio of approximately 1:1 and can be easily separated using silica gel column chromatography. Nuclear Overhauser effect measurements identified the conformations of the straight exo isomer and bent endo isomer. We discuss the origin of stereoselectivity, the anomeric effect, intermolecular ordering in the film state, and the performance of poly(3-hexylthiophene):substituted SAF6 OPV devices. Despite their identical optical and electrochemical properties, their solubilities and space-charge limited current mobilities are largely influenced by the stereoisomers, which leads to variation in the OPV efficiency. This study emphasizes the importance of fullerene stereochemistry for understanding the relationship between stereochemical structures and device output.