Temperature-dependent infrared and calorimetric studies on arsenicals adsorption from solution to hematite nanoparticles

Novel heterogeneous Fenton catalysts for promoting carbon iron electron transfer by one-step hydrothermal synthesization

Carbon materials play a crucial role in promoting the Fe(III)/Fe(II) redox cycle in heterogeneous Fenton reactions. However, the electron transfer efficiency between carbon and iron is typically low. In this study, we prepared a novel heterogeneous Fenton catalyst, humboldtine/hydrothermal carbon (Hum/HTC), using a one-step hydrothermal method and achieved about 100 % reduction in Fe(III) during synthesis. Moreover, the HTC continuously provided electrons to promote Fe(II) regeneration during the Fenton reaction. Electron paramagnetic resonance (EPR) and quenching experiments showed that Hum/HTC completely oxidized As(III) to As(V) via free radical and non-free radical pathways. Attenuated total reflectance Fourier-transform infrared (ATR-FTIR) and two-dimensional correlation spectroscopy (2D-COS) analyses revealed that monodentate mononuclear (MM) and bidentate binuclear (BB) structures were the dominant bonding methods for As(V) immobilization. 40 %Hum/HTC exhibited a maximum As(III) adsorption capacity of 167 mg/g, which was higher than that of most reported adsorbents. This study provides a novel strategy for the efficient reduction of Fe(III) during catalyst synthesis and demonstrates that HTC can continuously accelerate Fe(II) regeneration in heterogeneous Fenton reactions.

Oxide- and Silicate-Water Interfaces and Their Roles in Technology and the Environment

Interfacial reactions drive all elemental cycling on Earth and play pivotal roles in human activities such as agriculture, water purification, energy production and storage, environmental contaminant remediation, and nuclear waste repository management. The onset of the 21st century marked the beginning of a more detailed understanding of mineral aqueous interfaces enabled by advances in techniques that use tunable high-flux focused ultrafast laser and X-ray sources to provide near-atomic measurement resolution, as well as by nanofabrication approaches that enable transmission electron microscopy in a liquid cell. This leap into atomic- and nanometer-scale measurements has uncovered scale-dependent phenomena whose reaction thermodynamics, kinetics, and pathways deviate from previous observations made on larger systems. A second key advance is new experimental evidence for what scientists hypothesized but could not test previously, namely, interfacial chemical reactions are frequently driven by "anomalies" or "non-idealities" such as defects, nanoconfinement, and other nontypical chemical structures. Third, progress in computational chemistry has yielded new insights that allow a move beyond simple schematics, leading to a molecular model of these complex interfaces. In combination with surface-sensitive measurements, we have gained knowledge of the interfacial structure and dynamics, including the underlying solid surface and the immediately adjacent water and aqueous ions, enabling a better definition of what constitutes the oxide- and silicate-water interfaces. This critical review discusses how science progresses from understanding ideal solid-water interfaces to more realistic systems, focusing on accomplishments in the last 20 years and identifying challenges and future opportunities for the community to address. We anticipate that the next 20 years will focus on understanding and predicting dynamic transient and reactive structures over greater spatial and temporal ranges as well as systems of greater structural and chemical complexity. Closer collaborations of theoretical and experimental experts across disciplines will continue to be critical to achieving this great aspiration.

Application of infrared spectroscopy and its theoretical simulation to arsenic adsorption processes

Accurate detection and analysis of arsenic pollutants are an important means to enhance the ability to manage arsenic pollution. Infrared (IR) spectroscopy technology has the advantages of fast analysis speed, high resolution, and high sensitivity and can be monitored by real-time in situ analysis. This paper reviews the application of IR spectroscopy in the qualitative and quantitative analysis of inorganic and organic arsenic acid adsorbed by major minerals such as ferrihydrite (FH), hematite, goethite, and titanium dioxide. The IR spectroscopy technique cannot only identify different arsenic contaminants but also obtain the content and adsorption rate of arsenic contaminants in the solid phase. The reaction equilibrium constants and the degree of reaction conversion can be determined by constructing adsorption isotherms or combining them with modeling techniques. Theoretical calculations of IR spectra of mineral adsorbed arsenic pollutant systems based on density functional theory (DFT) and analysis and comparison of the measured and theoretically calculated characteristic peaks of IR spectra can reveal the microscopic mechanism and surface chemical morphology of the arsenic adsorption process. This paper systematically summarizes the qualitative and quantitative studies and theoretical calculations of IR spectroscopy in inorganic and organic arsenic pollutant adsorption systems, which provides new insights for accurate detection and analysis of arsenic pollutants and arsenic pollution control. PRACTITIONER POINTS: This paper reviews the application of infrared spectroscopy in the qualitative and quantitative analyses of inorganic and organic arsenic acid adsorbed by major minerals such as ferrihydrite, hematite, goethite, and titanium dioxide, which can help identify and evaluate the type and concentration of arsenic pollutants in water bodies. In this paper, theoretical calculations of infrared spectra of mineral adsorbed arsenic pollutant systems based on density functional theory reveal the adsorption mechanism of arsenic pollutants in water at the solid-liquid interface and help to develop targeted arsenic pollution control technologies. This paper provides a new and reliable analytical detection technique for the study of arsenic contaminants in water bodies.

Mechanistic In Situ ATR-FTIR Studies on the Adsorption and Desorption of Major Intermediates in CO2 Electrochemical Reduction on CuO Nanoparticles

Increasing levels of carbon dioxide (CO₂) from human activities is affecting the ecosystem and civilization as we know it. CO₂ removal from the atmosphere and emission reduction by heavy industries through carbon capture, utilization, and storage (CCUS) technologies to store or convert CO₂ to useful products or fuels is a popular approach to meet net zero targets by 2050. One promising process of CO₂ removal and conversion is CO₂ electrochemical reduction (CO₂ER) using metal and metal oxide catalysts, particularly copper-based materials. However, the current limitations of CO₂ER stem from the low product selectivity of copper electrocatalysts due to existing knowledge gaps of the reaction mechanisms using surfaces that normally have native oxide layers. Here, we report systematic control studies of the surface interactions of major intermediates in CO₂ER, formate, bicarbonate, and acetate, with CuO nanoparticles in situ and in real time using attenuated total reflection Fourier-transform infrared spectroscopy (ATR-FTIR). Spectra were collected as a function of concentration, pH, and time in the dark and the in absence of added electrolytes. Isotopic exchange experiments were also performed to elucidate the type of surface complexes from H/D exchange. Our results show that the organics and bicarbonate form mostly outer-sphere complexes mediated by hydrogen bonding with CuO nanoparticles with Gibbs free energy of adsorption of about -25 kJ mol^-1. The desorption kinetics of the surface species indicated relatively fast and slow regions reflective of the heterogeneity of sites that affect the strength of hydrogen bonding. These results suggest that hydrogen bonding, whether intermolecular or with surface sites on CuO nanoparticles, might be playing a more important role in the CO₂ER reaction mechanism than previously thought, contributing to the lack of product selectivity.

In Situ and Real-Time ATR-FTIR Temperature-Dependent Adsorption Kinetics Coupled with DFT Calculations of Dimethylarsinate and Arsenate on Hematite Nanoparticles

Temperature-dependent kinetic studies of the adsorption of critical pollutants onto reactive components in soils and removal technologies provide invaluable rate information and mechanistic insight. Using attenuated total internal reflection Fourier transform infrared spectroscopy, we collected in situ spectra as a function of time, concentration, and temperature in the range of 5-50 °C (278-323 K) for the adsorption of arsenate (iAs) and dimethylarsinate (DMA) on hematite nanoparticles at pH 7. These experimental data were modeled with density functional theory (DFT) calculations on the energy barriers between surface complexes. The Langmuir adsorption kinetic model was used to extract values of the fast (<5 min) and slow (6-10 min) observed adsorption rate, initial rate constants of adsorption and desorption, Arrhenius parameters, effective activation energies (ΔE_a), and pre-exponential factors (A). The trend in the kinetic parameters correlated with the type of surface complexes that iAs and DMA form, which are mostly bidentate binuclear compared to a mix of outer sphere and monodentate, respectively. The observed initial adsorption rates were found to be more sensitive to changes in the aqueous concentration of the arsenicals than slow rates. On average, iAs adsorbs 2.5× faster and desorbs 4× slower than dimethylarsinate (DMA). The ΔE_a and A values for the adsorption of iAs bidentate complexes are statistically higher than those extracted for outer-sphere DMA by a factor of 3. The DFT results on adsorption energies and ΔE_a barriers are consistent with the experimental data and provide a mechanistic explanation for the low ΔE_a values observed. The presence of defect sites with under-coordinated Fe atoms or exchangeable surface water (i.e., Fe-OH₂ groups) lowers activation barriers of adsorption. These results suggest that increasing organic substitutions on arsenate at the expense of As-O bonds decreases the effective energy barrier for complex formation and lowers the number of collisional orientations that result in binding to the hematite surface.

Interaction of Phosphate with Lithium Cobalt Oxide Nanoparticles: A Combined Spectroscopic and Calorimetric Study

Adsorption of small ions such as phosphates to the surfaces of metal oxides can significantly alter the behavior of these materials, especially when present in the nanoscale form. Lithium cobalt oxide is a good model system for understanding small-molecule interactions with emerging nanomaterials because of its widespread use in lithium ion batteries and its known activity as a water oxidation catalyst. Here, we present a thermodynamic analysis of phosphate adsorption to LiCoO₂ and corroborate the results with additional in situ techniques, including zeta potential measurements and attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy, at pH values relevant to potential environmental release scenarios. Flow microcalorimetry measurements of phosphate interaction with LiCoO₂ at pH 7.4 show that there are two distinct exothermic processes taking place. Time-sequence in situ ATR-FTIR with two-dimensional correlation analysis reveals the spectroscopic signatures of these processes. We interpret the data as an interaction of phosphate with LiCoO₂ that occurs through the release of two water molecules and is therefore, best described as a condensation process rather than a simple adsorption, consistent with prior studies, demonstrating that phosphate interaction with LiCoO₂ is highly irreversible. Additional measurements for over longer times of 5 months show that phosphate adsorption terminates with one surface layer and that continued transformation over longer periods of time arises from H⁺/Li⁺ exchange and slow transformation to a cobalt hydroxide, with phosphate adsorbed to the surface only. To the best of our knowledge, this is the first time that flow microcalorimetry and two-dimensional correlation spectroscopy have been applied in tandem to clarify the specific chemical reactions that occur at the interface of solids and adsorbates.

Impact of Phosphate Adsorption on Complex Cobalt Oxide Nanoparticle Dispersibility in Aqueous Media

A commonly overlooked and largely unknown aspect of assessing the environmental and biological safety of engineered nanomaterials is their transformation in aqueous systems. Complex metal oxides are an important class of materials for catalysis, energy storage, and water purification. However, the potential impact of nano complex metal oxides on the environment upon improper disposal is not well understood. We present a comprehensive analysis of the interaction of an environmentally relevant oxyanion, phosphate, with a complex metal oxide nanomaterial, lithium cobalt oxide. Our results show that adsorption of phosphate to the surface of these materials drastically impacts their surface charge, rendering them more stable in aqueous systems. The adsorbed phosphate remains on the surface over significant periods of time, suggesting that desorption is not kinetically favored. The implications of this interaction may be increased dispersibility and bioavailability of these materials in environmental water systems.

Metal-organic framework-based materials: superior adsorbents for the capture of toxic and radioactive metal ions

Highly efficient removal of metal ion pollutants, such as toxic and nuclear waste-related metal ions, remains a serious task from the biological and environmental standpoint because of their harmful effects on human health and the environment. Recently, highly porous metal-organic frameworks (MOFs), with excellent chemical stability and abundant functional groups, have represented a new addition to the area of capturing various types of hazardous metal ion pollutants. This review focuses on recent progress in reported MOFs and MOF-based composites as superior adsorbents for the efficient removal of toxic and nuclear waste-related metal ions. Aspects related to the interaction mechanisms between metal ions and MOF-based materials are systematically summarized, including macroscopic batch experiments, microscopic spectroscopy analysis, and theoretical calculations. The adsorption properties of various MOF-based materials are assessed and compared with those of other widely used adsorbents. Finally, we propose our personal insights into future research opportunities and challenges in the hope of stimulating more researchers to engage in this new field of MOF-based materials for environmental pollution management.

Ion Exchange Thermodynamics at the Rutile-Water Interface: Flow Microcalorimetric Measurements and Surface Complexation Modeling of Na-K-Rb-Cl-NO3 Adsorption

Flow microcalorimetry was used to investigate the energetics associated with Rb⁺, K⁺, Na⁺, Cl^-, and NO₃^- exchange at the rutile-water interface. Heats of exchange reflected differences in bulk hydration/dehydration enthalpies (Na⁺ > K⁺ > Rb⁺, and Cl^- > NO₃^-) such that exchanging Na⁺ or Cl^- from the surface was exothermic, reflecting their greater bulk hydration enthalpies. Exchange heats were measured at pH 2, 3.25, 5.8, and 11 and exhibited considerable differences as well as pH dependence. These trends were rationalized with the aid of a molecularly constrained surface complexation model (SCM) that incorporated the inner-sphere binding observed for the cations on the rutile (110) surface. Explicitly accounting for the inner-sphere binding configuration differences between Rb⁺, K⁺, and Na⁺, as well as accompanying differences in negative surface charge development, resulted in much better agreement with measured exchange ratios than by considering bulk hydration enthalpies alone. The observation that calculated exchange ratios agreed with those measured experimentally lends additional credence to the SCM. Consequently, flow microcalorimetry and surface complexation modeling are a useful complement of techniques for probing the energetics associated with ion exchange and adsorption processes and should also serve to help validate molecular simulations of interfacial energetics.

Defect creation in metal-organic frameworks for rapid and controllable decontamination of roxarsone from aqueous solution

Given the great harm to the human health of organic arsenic compounds (OACs), developing highly efficient adsorbents with both rapid adsorption rate and high saturation capacity is paramount important. Herein, Zr-based metal-organic frameworks (MOFs) of UiO-66 have been successfully exploited for the efficient decontamination of a typical organic arsenic compound of roxarsone (ROX) from aqueous solution. The influences of the most significant parameters such as contact time, adsorbate concentration, pH as well as ionic strength on the adsorption of ROX were investigated. The amount of missing-linker defects in UiO-66 was systematically tuned by changing the concentration of modulator in the reactants. The presence of the defects not only resulted in the dramatically enhanced porosity, but also induced the creation of ZrOH groups which served as the main active adsorption sites for efficient ROX sequestration. As a result, adsorptive capacity of ROX over UiO-66 could be improved to 730 mg/g, which was much higher than those of many reported adsorbents. Meanwhile, the adsorption equilibrium time could be reduced to as short as 30 min. These merits, combined with their excellent stability, prefigure the great potentials of these defect-tunable UiO-66 MOFs as adsorbents for the efficient removal of various OACs from the polluted water.

Surface interactions of monomethylarsonic acid with hematite nanoparticles studied using ATR-FTIR: adsorption and desorption kinetics

Monomethylarsonic acid (MMA) is an organoarsenical compound which, along with dimethylarsinic acid (DMA), poses health and environmental concerns. Little is known about the surface chemistry of MMA at the molecular level with materials relevant to geochemical environments and industrial sectors. We report the structure of MMA surface complexes and the adsorption/desorption kinetics of MMA to and from hematite as a model for reactive iron-containing materials commonly found in geosorbents and arsenic-removal technologies. Attenuated total internal reflectance Fourier transform infrared (ATR-FTIR) spectroscopy was used to study the surface interactions at the molecular level. Spectra of adsorbed MMA (MMA(ads)) were collected as a function of time and aqueous-phase concentration. Values for the apparent rates of adsorption and desorption were extracted from experimental data at pH 7 as a function of spectral components during the initial times of surface interactions (0–5 min). Results showed that MMA adsorbs on hematite nanoparticles with rates 1.3 to 1.6 times slower than arsenate. The desorption of MMA(ads) by hydrogen phosphate from hematite surfaces is 2× faster than arsenate, and proceeds with an overall nonunity order, suggesting the existence of more than one type of surface complex at equilibrium. Also, hydrogen phosphate leads to the desorption of about 67% of MMA(ads) compared with 26% of surface arsenate. Adsorption kinetics for aqueous hydrogen phosphate were also investigated in the absence and presence of surface arsenic and followed this order: fresh hematite > MMA/hematite ≥ iAs(V)/hematite. From this study, it can be inferred that, on average, the presence of the methyl group in MMA results in weaker surface interactions with hematite relative to arsenate under neutral pH because of the simultaneous formation of mono- and bidentate MMA complexes compared with predominantly bidentate complexes for arsenate.