Direct, rapid, and label-free detection of enzyme-substrate interactions in physiological buffers using CMOS-compatible nanoribbon sensors

Nanowire biosensors with olfactory proteins: towards a genuine electronic nose with single molecule sensitivity and high selectivity

We describe the concept and roadmap of an engineered electronic nose with specificity towards analytes that differ by as little as one carbon atom, and sensitivity of being able to electrically register a single molecule of analyte. The analyte could be anything that natural noses can detect, e.g. trinitrotoluene (TNT), cocaine, aromatics, volatile organic compounds etc. The strategy envisioned is to genetically engineer a fused olfactory odorant receptor (odorant receptor (OR), a membrane-bound G-protein coupled receptor (GPCR) with high selectivity) to an ion channel protein, which opens in response to binding of the ligand to the OR. The lipid bilayer supporting the fused sensing protein would be intimately attached to a nanowire or nanotube network (either via a covalent tether or a non-covalent physisorption process), which would electrically detect the opening of the ion channel, and hence the binding of a single ligand to a single OR protein domain. Three man-made technological advances: (1) fused GPCR to ion channel protein, (2) nanowire sensing of single ion channel activity, and (3) lipid bilayer to nanotube/nanowire tethering chemistry and on natural technology (sensitivity and selectivity of OR domains to specific analytes) each have been demonstrated and/or studied independently. The combination of these three technological advances and the result of millions of years of evolution of OR proteins would enable the goal of single molecule sensing with specificity towards analytes that differ by as little as one carbon atom. This is both a review of the past and a vision of the future.

Chip for dielectrophoretic microbial capture, separation and detection I: theoretical basis of electrode design

We model the dielectrophoretic response ofE. colibacterial cells and red blood cells, upon exposure to an electric field. We model the separation, capture, and release mechanisms under flow conditions in a microfluidic channel and show under which conditions efficient separation of different cell types occurs. The modelling work is aimed to guide the separation electrode architecture and design for experimental validation of the model. The dielectrophoretic force is affected both by the geometry of the electrodes (the gradient of the electric field), the Re{CM(ω)} factor, and the permittivity of the medium ϵ_m. Our modelling makes testable predictions and shows that designing the electrode structure to ensure structure periodicity with spacing between consecutive traps smaller than the length of the depletion zone ensures efficient capture and separation. Such electrode system has higher capture and separation efficiency than systems with the established circular electrode architecture. The simulated, modelled microfluidic design allows for the separated bacteria, concentrated by dedicated dielectrophoretic regions, to be subsequently detected using label-free functionalized nanowire sensors. The experimental validation of the modelling work presented here and the validation of the theoretical design constraints of the chip electrode architecture is presented in the companion paper in the same issue (Weber MUet al2022 Chip for dielectrophoretic Microbial Capture, Separation and Detection II: Experimental Study).

A Fast and Label-Free Potentiometric Method for Direct Detection of Glutamine with Silicon Nanowire Biosensors

In this paper, a potentiometric method is used for monitoring the concentration of glutamine in the bioprocess by employing silicon nanowire biosensors. Just one hydrolyzation reaction was used, which is much more convenient compared with the two-stage reactions in the published papers. For the silicon nanowire biosensor, the Al2O3 sensing layer provides a highly sensitive to solution-pH, which has near-Nernstian sensitivity. The sensitive region to detect glutamine is from ≤40 μM to 20 mM. The Sigmoidal function was used to model the pH-signal variation versus the glutamine concentration. Compared with the amperometric methods, a consistent result from different devices could be directly obtained. It is a fast and direct method achieved with our real-time setup. Also, it is a label-free method because just the pH variation of the solution is monitored. The obtained results show the feasibility of the potentiometric method for monitoring the glutamine concentrations in fermentation processes. Our approach in this paper can be applied to various analytes.

Cyclic swelling enabled, electrically conductive 3D porous structures for microfluidic urinalysis devices

Urinalysis is a simple and non-invasive approach for the diagnosis and monitoring of organ health and also is often used as a facile technique in assessment of substance abuse. However, quantitative urinalysis is predominantly limited to clinical laboratories. Here, we present an electrical sensing based, reusable, cellular microfluidic device that offers a fast urinalysis through quantitative reading of the electrical signals. The spatial soft porous scaffolds decorated with electrically conductive multiwalled carbon nanotubes that are capable of physically interacting with biomarkers in urine are developed through a cyclic swelling/absorption process of soft materials and are utilized to manufacture the cellular microfluidic device. The sensing capability, sensitivity and reusability (via sunlight exposure) of the device to monitor red blood cells, Escherichia coli, and albumin are systemically demonstrated by programming mechanical deformation of porous scaffolds. Ex vivo experiments in disease mouse models confirm the diagnosis robustness of the device in comparable results with existing biochemical tests. The full integration of electrically conductive nanomaterials into soft scaffolds provides a foundation for devising bioelectronic devices with mechanically programmable microfluidic features in a low-cost manner, with broad applications for rapid disease diagnoses through body fluid.

Review on Nanoparticles and Nanostructured Materials: Bioimaging, Biosensing, Drug Delivery, Tissue Engineering, Antimicrobial, and Agro-Food Applications

In the last few decades, the vast potential of nanomaterials for biomedical and healthcare applications has been extensively investigated. Several case studies demonstrated that nanomaterials can offer solutions to the current challenges of raw materials in the biomedical and healthcare fields. This review describes the different nanoparticles and nanostructured material synthesis approaches and presents some emerging biomedical, healthcare, and agro-food applications. This review focuses on various nanomaterial types (e.g., spherical, nanorods, nanotubes, nanosheets, nanofibers, core-shell, and mesoporous) that can be synthesized from different raw materials and their emerging applications in bioimaging, biosensing, drug delivery, tissue engineering, antimicrobial, and agro-foods. Depending on their morphology (e.g., size, aspect ratio, geometry, porosity), nanomaterials can be used as formulation modifiers, moisturizers, nanofillers, additives, membranes, and films. As toxicological assessment depends on sizes and morphologies, stringent regulation is needed from the testing of efficient nanomaterials dosages. The challenges and perspectives for an industrial breakthrough of nanomaterials are related to the optimization of production and processing conditions.

Highly sensitive, scalable, and rapid SARS-CoV-2 biosensor based on In2O3 nanoribbon transistors and phosphatase

Developing convenient and accurate SARS-CoV-2 antigen test and serology test is crucial in curbing the global COVID-19 pandemic. In this work, we report an improved indium oxide (In₂O₃) nanoribbon field-effect transistor (FET) biosensor platform detecting both SARS-CoV-2 antigen and antibody. Our FET biosensors, which were fabricated using a scalable and cost-efficient lithography-free process utilizing shadow masks, consist of an In₂O₃ channel and a newly developed stable enzyme reporter. During the biosensing process, the phosphatase enzymatic reaction generated pH change of the solution, which was then detected and converted to electrical signal by our In₂O₃ FETs. The biosensors applied phosphatase as enzyme reporter, which has a much better stability than the widely used urease in FET based biosensors. As proof-of-principle studies, we demonstrate the detection of SARS-CoV-2 spike protein in both phosphate-buffered saline (PBS) buffer and universal transport medium (UTM) (limit of detection [LoD]: 100 fg/mL). Following the SARS-CoV-2 antigen tests, we developed and characterized additional sensors aimed at SARS-CoV-2 IgG antibodies, which is important to trace past infection and vaccination. Our spike protein IgG antibody tests exhibit excellent detection limits in both PBS and human whole blood ((LoD): 1 pg/mL). Our biosensors display similar detection performance in different mediums, demonstrating that our biosensor approach is not limited by Debye screening from salts and can selectively detect biomarkers in physiological fluids. The newly selected enzyme for our platform performs much better performance and longer shelf life which will lead our biosensor platform to be capable for real clinical diagnosis usage.

ELECTRONIC SUPPLEMENTARY MATERIAL

Supplementary material (materials and methods for device fabrication, functionalization of In₂O₃ devices, photographs of the liquid gate measurement setup, mobilities of the nine devices labeled in Fig. 1(b), family curves of I _DS-V _DS with the liquid gate setup and current change after bubbling the substrate solution (current vs. time curve for S1 antigen detection)) is available in the online version of this article at 10.1007/s12274-022-4190-0.

Waterproof, flexible field-effect transistors with submicron monocrystalline Si nanomembrane derived encapsulation for continuous pH sensing

To understand the physio-pathological state of patients suffering from chronic diseases, scientists and clinicians need sensors to track chemical signals in real-time. However, the lack of stable, safe, and scalable biochemical sensing platforms capable of continuous operation in liquid environments imposes significant challenges in the timely diagnosis, intervention, and treatment of chronic conditions. This work reports a novel strategy for fabricating waterproof and flexible biochemical sensors with active electronic components, which feature a submicron encapsulation layer derived from monocrystalline Si nanomembranes with a high structural integrity due to the high formation temperature (>1000 °C). The ultrathin, yet dense and low-defect encapsulation enables continuous operation of field-effect transistors in biofluids for chemical sensing. The excellent stability in liquid environment and pH sensing performance of such transistors suggest their great potential as the foundation of waterproof and scalable biochemical sensors with active functionalities in the future. The understandings, knowledge base, and demonstrations for pH sensing reported here set the stage for the next generation long-term biosensing with a broad applicability in biomedical research, food science, and advanced healthcare.

Optimal field-effect transistor operation for high-resolution biochemical measurements

Field-effect transistors (FETs) are powerful tools for sensitive measurements of numerous biomarkers (e.g., proteins, nucleic acids, and antigen) and gaseous species. Most research studies in this field focused on building discrete devices with high performance. We show that instrumentation that is commonly used in multiple areas of physics and engineering can greatly improve the performance of measurement systems that embed FET-based transducers for biological applications. We review the state-of-the-art instrumentation in the field as applied to sensing with FETs. We show how high-performance dual-gate 2D FETs that we recently developed, when operated using closed-loop proportional-integral-derivative control, can drastically improve both the sensitivity and resolution. We further show that this closed-loop control approach can be extended to commonly used single-gate silicon FETs. The generalizability of the results will allow their application to virtually any previously developed FET-based sensor. Finally, we provide insight into further optimization and performance benefits that can be extracted by using the closed-loop feedback approach for applications in biosensing.

Hafnium oxide layer-enhanced single-walled carbon nanotube field-effect transistor-based sensing platform

Single-walled carbon nanotube-based field effect transistors (SWCNT-FETs) are ideal candidates for fabricating sensors and have been widely used for chemical sensing applications. SWCNT-FETs have low selectivity because of the environmentally sensitive electronic properties of SWCNTs, and SWCNT-FETs also show a high noise signal and poor sensitivity because of charge trapping from Si-OH hydration of the SiO₂/Si substrate on the SWCNTs. Herein, poly (4-vinylpyridine) (P4VP) was used for noncovalent attachment to SWCNTs and selective binding to copper ions (Cu²⁺). Importantly, the introduction of a hafnium-oxide (HfO₂) layer through atomic layer deposition (ALD) overcame the charge trapping by SiO₂ hydration and remarkably decreased the interference signal. The sensitivity of the P4VP/SWCNT/HfO₂-FET sensor for Cu²⁺ was 7.9 μA μM^-1, which was approximately 100 times higher than that of the P4VP/SWCNT/SiO₂-FET sensor, and its limit of detection (LOD) was as low as 33 pmol L^-1. Thus, the P4VP/SWCNT/HfO₂-FET sensor is a promising candidate for the development of Cu²⁺-selective sensors and can be designed for the large-scale manufacturing of custom-made sensors in the future.

Evanescent Wave Optical Fiber Sensors Using Enzymatic Hydrolysis on Nanostructured Polyaniline for Detection of β-Lactam Antibiotics in Food and Environment

β-Lactam antibiotics such as penicillins and cephalosporins are extensively used for human infection therapy. Consistent unintended exposure to these antibiotics via food and water is known to promote antibiotic-resistant bacterial pathogenesis with high morbidity and mortality in humans. An optical enzymatic biosensor for rapid and point-of-use detection of these antibiotics in food and water has been developed and tested. Enzymatic hydrolysis of β-lactams, on the electroactive polyaniline nanofibers, altered the polymeric backbone of the nanofibers, from emeraldine base form to emeraldine salt, which was measured as an increase in evanescent wave absorbance at 435 nm. The sensors were calibrated by spiking antibiotic-free milk with ceftazidime (as a model β-lactam analyte) in a linear range of 0.36-3600 nM (R² = 0.98). The calibration was further validated for packaged milk, local cow milk, and buffalo milk. A similar calibration was devised for chicken meat samples in a linear range of 9-1800 nM (R² = 0.982) and tap water in a linear range of 0.18-180 nM (R² = 0.99). Interestingly, it was possible to use the same calibration for the determination of other β-lactam antibiotics (ampicillin, amoxicillin, and cefotaxime), which reflects the usefulness of the sensor for wide-scale deployment. The sensor performance was validated with a wastewater sample, from a wastewater treatment plant (WWTP), qualitatively analyzed by high-resolution liquid chromatography coupled with mass spectroscopy for detection of β-lactams. The sensor scheme developed and tested is of grassroot relevance as a quick solution for measurement of β-lactam residues in food and environment.

Nanoreporter of an Enzymatic Suicide Inactivation Pathway

Enzymatic suicide inactivation, a route of permanent enzyme inhibition, is the mechanism of action for a wide array of pharmaceuticals. Here, we developed the first nanosensor that selectively reports the suicide inactivation pathway of an enzyme. The sensor is based on modulation of the near-infrared fluorescence of an enzyme-bound carbon nanotube. The nanosensor responded selectively to substrate-mediated suicide inactivation of the tyrosinase enzyme via bathochromic shifting of the nanotube emission wavelength. Mechanistic investigations revealed that singlet oxygen generated by the suicide inactivation pathway induced the response. We used the nanosensor to quantify the degree of enzymatic inactivation by measuring response rates to small molecule tyrosinase modulators. This work resulted in a new capability of interrogating a specific route of enzymatic death. Potential applications include drug screening and hit-validation for compounds that elicit or inhibit enzymatic inactivation and single-molecule measurements to assess population heterogeneity in enzyme activity.

Rapid, quantitative therapeutic screening for Alzheimer's enzymes enabled by optimal signal transduction with transistors

We show that commercially sourced n-channel silicon field-effect transistors (nFETs) operating above their threshold voltage with closed loop feedback to maintain a constant channel current allow a pH readout resolution of (7.2 ± 0.3) × 10-3 at a bandwidth of 10 Hz, or ≈3-fold better than the open loop operation commonly employed by integrated ion-sensitive field-effect transistors (ISFETs). We leveraged the improved nFET performance to measure the change in solution pH arising from the activity of a pathological form of the kinase Cdk5, an enzyme implicated in Alzheimer's disease, and showed quantitative agreement with previous measurements. The improved pH resolution was realized while the devices were operated in a remote sensing configuration with the pH sensing element off-chip and connected electrically to the FET gate terminal. We compared these results with those measured by using a custom-built dual-gate 2D field-effect transistor (dg2DFET) fabricated with 2D semi-conducting MoS2 channels and a signal amplification of 8. Under identical solution conditions the nFET performance approached the dg2DFETs pH resolution of (3.9 ± 0.7) × 10-3. Finally, using the nFETs, we demonstrated the effectiveness of a custom polypeptide, p5, as a therapeutic agent in restoring the function of Cdk5. We expect that the straight-forward modifications to commercially sourced nFETs demonstrated here will lower the barrier to widespread adoption of these remote-gate devices and enable sensitive bioanalytical measurements for high throughput screening in drug discovery and precision medicine applications.

Engineering two-dimensional metal oxides via surface functionalization for biological applications

Schematic illustration of 2D MO nanosheets for applications in biosystems.

Modularized Field-Effect Transistor Biosensors

Field-effect transistors (FETs), when functionalized with proper biorecognition elements (such as antibodies or enzymes), represent a unique platform for real-time, specific, label-free transduction of biochemical signals. However, direct immobilization of biorecognition molecules on FETs imposes limitations on reprogrammability, sensor regeneration, and robust device handling. Here we demonstrate a modularized design of FET biosensors with separate biorecognition and transducer modules, which are capable of reversible assembly and disassembly. In particular, hydrogel "stamps" immobilizing bioreceptors have been chosen to build biorecognition modules to reliably interface with FET transducers structurally and functionally. Successful detection of penicillin down to 0.25 mM has been achieved with a penicillinase-encoded hydrogel module, demonstrating effective signal transduction across the hybrid interface. Moreover, sequential integration of urease- and penicillinase-encoded modules on the same FET device allows us to reprogram the sensing modality without cross-contamination. In addition to independent bioreceptor encoding, the modular design also fosters sophisticated control of sensing kinetics by modulating the physiochemical microenvironment in the biorecognition modules. Specifically, the distinction in hydrogel porosity between polyethylene glycol and gelatin enables controlled access and detection of larger molecules, such as poly-l-lysine (MW 150-300 kDa), only through the gelatin module. Biorecognition modules with standardized interface designs have also been exploited to comply with additive mass fabrication by 3D printing, demonstrating potential for low cost, ease of storage, multiplexing, and great customizability for personalized biosensor production. This generic concept presents a unique integration strategy for modularized bioelectronics and could broadly impact hybrid device development.

Quantum capacitance-limited MoS2 biosensors enable remote label-free enzyme measurements

We have demonstrated atomically thin, quantum capacitance-limited, field-effect transistors (FETs) that enable the detection of pH changes with 75-fold higher sensitivity (≈4.4 V per pH) over the Nernst value of 59 mV per pH at room temperature when used as a biosensor. The transistors, which are fabricated from monolayer films of MoS2, use a room temperature ionic liquid (RTIL) in place of a conventional oxide gate dielectric and exhibit very low intrinsic noise resulting in a pH resolution of 92 × 10-6 at 10 Hz. This high device performance, which is a function of the structure of our device, is achieved by remotely connecting the gate to a pH sensing element allowing the FETs to be reused. Because pH measurements are fundamentally important in biotechnology, the increased resolution demonstrated here will benefit numerous applications ranging from pharmaceutical manufacturing to clinical diagnostics. As an example, we experimentally quantified the function of the kinase Cdk5, an enzyme implicated in Alzheimer's disease, at concentrations that are 5-fold lower than physiological values, and with sufficient time-resolution to allow the estimation of both steady-state and kinetic parameters in a single experiment. The high sensitivity, increased resolution, and fast turnaround time of the measurements will allow the development of early diagnostic tools and novel therapeutics to detect and treat neurological conditions years before currently possible.

Solidly mounted resonator sensor for biomolecule detections

We report the fabrication of a solidly mounted resonator (SMR) that can also function as a sensor for biological molecules. The SMR, consisting of a Au electrode, aluminum nitride (AlN) piezoelectric thin film and Bragg acoustic reflector, was fabricated on a Si substrate by radio frequency (RF) magnetron sputtering. The Bragg acoustic reflector, made entirely of metal, has small internal stress and good heat conduction. Human immunoglobulin G (IgG) antibody was immobilized on the modified (by self-assembled monolayer method) Au electrode surface of the SMR and goat anti-human IgG antigen was captured through the specificity of bond between the antibody and antigen on the electrode surface. We found a linear relationship between the resonant frequency shift and the concentration of goat anti-human IgG antigen for concentrations smaller than 0.4 mg ml⁻¹ and a relatively constant frequency shift for concentrations greater than 0.5 mg ml⁻¹. A series of interference experiments can prove that the selectivity of the sensor is satisfactory. Our findings suggest that the SMR sensor is an attractive alternative for biomolecule detection.

We report the fabrication of a solidly mounted resonator (SMR) that can also function as a sensor for biological molecules.

Hydrogel Gate Graphene Field-Effect Transistors as Multiplexed Biosensors

Nanoscale field-effect transistors (FETs) represent a unique platform for real time, label-free transduction of biochemical signals with unprecedented sensitivity and spatiotemporal resolution, yet their translation toward practical biomedical applications remains challenging. Herein, we demonstrate the potential to overcome several key limitations of traditional FET sensors by exploiting bioactive hydrogels as the gate material. Spatially defined photopolymerization is utilized to achieve selective patterning of polyethylene glycol on top of individual graphene FET devices, through which multiple biospecific receptors can be independently encapsulated into the hydrogel gate. The hydrogel-mediated integration of penicillinase was demonstrated to effectively catalyze enzymatic reaction in the confined microenvironment, enabling real time, label-free detection of penicillin down to 0.2 mM. Multiplexed functionalization with penicillinase and acetylcholinesterase has been demonstrated to achieve highly specific sensing. In addition, the microenvironment created by the hydrogel gate has been shown to significantly reduce the nonspecific binding of nontarget molecules to graphene channels as well as preserve the encapsulated enzyme activity for at least one week, in comparison to free enzymes showing significant signal loss within one day. This general approach presents a new biointegration strategy and facilitates multiplex detection of bioanalytes on the same platform, which could underwrite new advances in healthcare research.

Selective non-enzymatic total bilirubin detection in serum using europium complexes with different β-diketone-derived ligands as luminescence probes

Three europium(III) complexes, Eu(ectfd)₃ (Hectfd = 1-(9-ethyl-9H-carbazol-7-yl)-4,4,4-trifluorobutane-1,3-dione), Eu(tta)₃ (Htta = 4,4,4-trifluoro-1-(thiophen-2-yl)-butane-1,3-dione), and Eu(dbt)₃ (Hdbt = 2-(4',4',4'-trifluoro-1',3'-dioxobutyl)dibenzothiophene), were synthesized and employed to detect total bilirubin (BR) in blood-serum samples. UV-visible absorption and fluorescence (FL) spectroscopies were used to evaluate the selectivity of each europium (III) fluorescence probe to BR, which was shown to remarkably reduce the luminescence intensities of the europium(III) complexes at a wavelength of 612 nm. The luminescence intensity of each complex is linearly related to BR concentration. Eu(tta)₃ was shown to be the more-appropriate fluorescence probe for the sensitive and reliable detection of total BR in blood serum samples than either Eu(ectfd)₃ or Eu(dbt)₃. This observation can be ascribed to special σ-hole bonding between Htta and BR. In addition, the optimal pH test conditions for the detection of BR in human serum by the Eu(tta)₃ probe were determined. Sensitivity was shown to be dramatically affected by the pH of the medium. The experimental results reveal that pH 7.5 is optimal for this probe, which coincides with the pH of human serum. Furthermore, BR detection using the Eu(tta)₃ luminescence probe is simple, practical, and relatively free of interference from coexisting substances; it has a minimum detection limit (DL) of 68 nM and is a potential candidate for the routine assessment of total BR in serum samples. Graphical Abstract ᅟ.

Sensing the electrical activity of single ion channels with top-down silicon nanoribbons

Using top-down fabricated silicon nanoribbons, we measure the opening and closing of ion channels alamethicin and gramicidin A. A capacitive model of the system is proposed to demonstrate that the geometric capacitance of the nanoribbon is charged by ion channel currents. The integration of top-down nanoribbons with electrophysiology holds promise for integration of electrically active living systems with artificial electronics.

Photoconductivity, pH Sensitivity, Noise, and Channel Length Effects in Si Nanowire FET Sensors

Silicon nanowire (NW) field-effect transistor (FET) sensors of various lengths were fabricated. Transport properties of Si NW FET sensors were investigated involving noise spectroscopy and current-voltage (I-V) characterization. The static I-V dependencies demonstrate the high quality of fabricated silicon FETs without leakage current. Transport and noise properties of NW FET structures were investigated under different light illumination conditions, as well as in sensor configuration in an aqueous solution with different pH values. Furthermore, we studied channel length effects on the photoconductivity, noise, and pH sensitivity. The magnitude of the channel current is approximately inversely proportional to the length of the current channel, and the pH sensitivity increases with the increase of channel length approaching the Nernst limit value of 59.5 mV/pH. We demonstrate that dominant 1/f-noise can be screened by the generation-recombination plateau at certain pH of the solution or external optical excitation. The characteristic frequency of the generation-recombination noise component decreases with increasing of illumination power. Moreover, it is shown that the measured value of the slope of 1/f-noise spectral density dependence on the current channel length is 2.7 which is close to the theoretically predicted value of 3.

A Sub-30 mpH Resolution Thin Film Transistor-Based Nanoribbon Biosensing Platform

We present a complete biosensing system that comprises a Thin Film Transistor (TFT)-based nanoribbon biosensor and a low noise, high-performance bioinstrumentation platform, capable of detecting sub-30 mpH unit changes, validated by an enzymatic biochemical reaction. The nanoribbon biosensor was fabricated top-down with an ultra-thin (15 nm) polysilicon semiconducting channel that offers excellent sensitivity to surface potential changes. The sensor is coupled to an integrated circuit (IC), which combines dual switched-capacitor integrators with high precision analog-to-digital converters (ADCs). Throughout this work, we employed both conventional pH buffer measurements as well as urea-urease enzymatic reactions for benchmarking the overall performance of the system. The measured results from the urea-urease reaction demonstrate that the system can detect urea in concentrations as low as 25 μM, which translates to a change of 27 mpH, according to our initial pH characterisation measurements. The attained accuracy and resolution of our system as well as its low-cost manufacturability, high processing speed and portability make it a competitive solution for applications requiring rapid and accurate results at remote locations; a necessity for Point-of-Care (POC) diagnostic platforms.

Diverse Applications of Nanomedicine

The design and use of materials in the nanoscale size range for addressing medical and health-related issues continues to receive increasing interest. Research in nanomedicine spans a multitude of areas, including drug delivery, vaccine development, antibacterial, diagnosis and imaging tools, wearable devices, implants, high-throughput screening platforms, etc. using biological, nonbiological, biomimetic, or hybrid materials. Many of these developments are starting to be translated into viable clinical products. Here, we provide an overview of recent developments in nanomedicine and highlight the current challenges and upcoming opportunities for the field and translation to the clinic.

Real-time reliable determination of binding kinetics of DNA hybridization using a multi-channel graphene biosensor

Reliable determination of binding kinetics and affinity of DNA hybridization and single-base mismatches plays an essential role in systems biology, personalized and precision medicine. The standard tools are optical-based sensors that are difficult to operate in low cost and to miniaturize for high-throughput measurement. Biosensors based on nanowire field-effect transistors have been developed, but reliable and cost-effective fabrication remains a challenge. Here, we demonstrate that a graphene single-crystal domain patterned into multiple channels can measure time- and concentration-dependent DNA hybridization kinetics and affinity reliably and sensitively, with a detection limit of 10 pM for DNA. It can distinguish single-base mutations quantitatively in real time. An analytical model is developed to estimate probe density, efficiency of hybridization and the maximum sensor response. The results suggest a promising future for cost-effective, high-throughput screening of drug candidates, genetic variations and disease biomarkers by using an integrated, miniaturized, all-electrical multiplexed, graphene-based DNA array.

Monitoring DNA binding and single-base mismatches accurately in real time is difficult, especially for miniaturized devices. Here the authors report a graphene field-effect transistor array capable of reliably measuring DNA hybridization kinetics and affinity at the picomolar level.

Highly Sensitive and Quick Detection of Acute Myocardial Infarction Biomarkers Using In2O3 Nanoribbon Biosensors Fabricated Using Shadow Masks

We demonstrate a scalable and facile lithography-free method for fabricating highly uniform and sensitive In₂O₃ nanoribbon biosensor arrays. Fabrication with shadow masks as the patterning method instead of conventional lithography provides low-cost, time-efficient, and high-throughput In₂O₃ nanoribbon biosensors without photoresist contamination. Combined with electronic enzyme-linked immunosorbent assay for signal amplification, the In₂O₃ nanoribbon biosensor arrays are optimized for early, quick, and quantitative detection of cardiac biomarkers in diagnosis of acute myocardial infarction (AMI). Cardiac troponin I (cTnI), creatine kinase MB (CK-MB), and B-type natriuretic peptide (BNP) are commonly associated with heart attack and heart failure and have been selected as the target biomarkers here. Our approach can detect label-free biomarkers for concentrations down to 1 pg/mL (cTnI), 0.1 ng/mL (CK-MB), and 10 pg/mL (BNP), all of which are much lower than clinically relevant cutoff concentrations. The sample collection to result time is only 45 min, and we have further demonstrated the reusability of the sensors. With the demonstrated sensitivity, quick turnaround time, and reusability, the In₂O₃ nanoribbon biosensors have shown great potential toward clinical tests for early and quick diagnosis of AMI.

Integration of a Droplet-Based Microfluidic System and Silicon Nanoribbon FET Sensor

We present a novel microfluidic system that integrates droplet microfluidics with a silicon nanoribbon field-effect transistor (SiNR FET), and utilize this integrated system to sense differences in pH. The device allows for selective droplet transfer to a continuous water phase, actuated by dielectrophoresis, and subsequent detection of the pH level in the retrieved droplets by SiNR FETs on an electrical sensor chip. The integrated microfluidic system demonstrates a label-free detection method for droplet microfluidics, presenting an alternative to optical fluorescence detection. In this work, we were able to differentiate between droplet trains of one pH-unit difference. The pH-based detection method in our integrated system has the potential to be utilized in the detection of biochemical reactions that induce a pH-shift in the droplets.

Dual-gate polysilicon nanoribbon biosensors enable high sensitivity detection of proteins

We demonstrate the advantages of dual-gate polysilicon nanoribbon biosensors with a comprehensive evaluation of different measurement schemes for pH and protein sensing. In particular, we compare the detection of voltage and current changes when top- and bottom-gate bias is applied. Measurements of pH show that a large voltage shift of 491 mV pH(-1) is obtained in the subthreshold region when the top-gate is kept at a fixed potential and the bottom-gate is varied (voltage sweep). This is an improvement of 16 times over the 30 mV pH(-1) measured using a top-gate sweep with the bottom-gate at a fixed potential. A similar large voltage shift of 175 mV is obtained when the protein avidin is sensed using a bottom-gate sweep. This is an improvement of 20 times compared with the 8.8 mV achieved from a top-gate sweep. Current measurements using bottom-gate sweeps do not deliver the same signal amplification as when using bottom-gate sweeps to measure voltage shifts. Thus, for detecting a small signal change on protein binding, it is advantageous to employ a double-gate transistor and to measure a voltage shift using a bottom-gate sweep. For top-gate sweeps, the use of a dual-gate transistor enables the current sensitivity to be enhanced by applying a negative bias to the bottom-gate to reduce the carrier concentration in the nanoribbon. For pH measurements, the current sensitivity increases from 65% to 149% and for avidin sensing it increases from 1.4% to 2.5%.

Real-Time Label-Free Direct Electronic Monitoring of Topoisomerase Enzyme Binding Kinetics on Graphene

Monolayer graphene field-effect sensors operating in liquid have been widely deployed for detecting a range of analyte species often under equilibrium conditions. Here we report on the real-time detection of the binding kinetics of the essential human enzyme, topoisomerase I interacting with substrate molecules (DNA probes) that are immobilized electrochemically on to monolayer graphene strips. By monitoring the field-effect characteristics of the graphene biosensor in real-time during the enzyme-substrate interactions, we are able to decipher the surface binding constant for the cleavage reaction step of topoisomerase I activity in a label-free manner. Moreover, an appropriate design of the capture probes allows us to distinctly follow the cleavage step of topoisomerase I functioning in real-time down to picomolar concentrations. The presented results are promising for future rapid screening of drugs that are being evaluated for regulating enzyme activity.

Electrochemical processes and mechanistic aspects of field-effect sensors for biomolecules

Electronic biosensing is a leading technology for determining concentrations of biomolecules. In some cases, the presence of an analyte molecule induces a measured change in current flow, while in other cases, a new potential difference is established. In the particular case of a field effect biosensor, the potential difference is monitored as a change in conductance elsewhere in the device, such as across a film of an underlying semiconductor. Often, the mechanisms that lead to these responses are not specifically determined. Because improved understanding of these mechanisms will lead to improved performance, it is important to highlight those studies where various mechanistic possibilities are investigated. This review explores a range of possible mechanistic contributions to field-effect biosensor signals. First, we define the field-effect biosensor and the chemical interactions that lead to the field effect, followed by a section on theoretical and mechanistic background. We then discuss materials used in field-effect biosensors and approaches to improving signals from field-effect biosensors. We specifically cover the biomolecule interactions that produce local electric fields, structures and processes at interfaces between bioanalyte solutions and electronic materials, semiconductors used in biochemical sensors, dielectric layers used in top-gated sensors, and mechanisms for converting the surface voltage change to higher signal/noise outputs in circuits.