Gold Nanorod Based Selective Identification of Escherichia coli Bacteria Using Two-Photon Rayleigh Scattering Spectroscopy

Device-Physics Realization of ZnO-MWCNT Nanostructure-Based Field-Effect Biosensor for Ultrasensitive Simultaneous Genomic Detection of Foodborne Pathogens

The complex and versatile interactions among the wide variety of the nanostructures and the target analytes have primarily limited the detailed investigation of the transduction mechanism of nanomaterial-assisted electrical signal-based biosensors despite their high sensitivity, low-cost, portability, and ease of deployment. Hence, no common ground is formed detailing the principle of operation, demanding a strong need for systematic examination instead of hit and trial. Therefore, a maiden mechanistic investigation has been carried out in this paper for a field-effect-based biosensor device relying on the energy band diagram and the surface potential profile. To demonstrate the experimental evidence and appreciate the importance of food safety, three hazardous foodborne pathogens (Proteus mirabilis, Escherichia coli, and Clostridium botulinum) have been detected herein. The biosensor device, built on a hydrothermally synthesized zinc oxide and MWCNT (ZnO-MWCNT) composite nanostructure, simultaneously incorporates three fairly specific ss-DNA probes. Furthermore, the unmet challenge of biosensor device variability is addressed through the optimum selection of operating voltage of the device via a unique "voltage-selection-algorithm". We believe that the rigorous experimentation and the insightful device-physics realization demonstrated in this work will pave the way for a future decisive biosensor platform.

Probe-free nanosensor for the detection of Salmonella using gold nanorods as an electroactive modulator

Salmonellosis is a symptomatic infection, a foodborne disease, caused by Salmonella that enters the body through the ingestion of contaminated food. In this study, a novel electrochemical biosensor integrated with gold nanorods (GNRs) was used to explore the interaction between in-house generated antibodies with Salmonella serovars. Under optimal conditions, the proposed immunosensor depicted a linear range of detection (1-1 × 10⁵) CFU/mL witha detection limit of 105 and 23 colony forming units (CFU) ofS. entandS. typhirespectively. The designed GNR/S. ent/S. typhi/Ab immunosensor was able to successfully detectS. ent/S. typhiin spiked meat and milk samples respectively, with a long shelf life, good repeatability, as well as reproducibility under optimised conditions. Along with the ease of fabrication, the developed electrode produced a highly specific response, and displayed negligible cross reactivity with other Salmonella species. Moreover, the established detection technique may be used as an alternative to conventional analytical approaches for rapid and sensitivediagnosis of Salmonellosis.

On the Synergism of Biogenic Gold Nanoparticles and Hydroxyaluminum Phthalocyanines in the Photoeradication of Staphylococcus aureus

Due to the unusual properties of gold nanoparticles, these structures are widely used in medicine and biology. This paper describes for the first time the synthesis of colloidal gold nanoparticles by the cell-free filtrate obtained from the Coriolus versicolor biomass and the use of these biogenic nanostructures to increase the photosensitizing efficiency of di- (AlPcS₂) and tetrasulfonated (AlPcS₄) hydroxyaluminum phthalocyanines in antibacterial photodynamic therapy. The obtained monodisperse particles were extremely stable, and this remarkable stability was due to the presence of phosphoprotein as a capping agent. The studied gold nanoparticles had a spherical shape, were uniformly distributed, and were characterized by a single plasmon band at wavelength of 514-517 nm. Almost 60% of the gold particles were found to be in the range of 13 to 15 nm. In accordance with the regulations of the American Microbiological Society, indicating that any antimicrobial technique must kill at least 3 log CFU (99.9%) to be accepted as "antimicrobial", this mortality of Staphylococcus aureus was shown to be achieved in the presence of AlPcS₄ + AuNPs mixture and 4.8 J cm^-2 light dose compared to AlPcS₄ alone, which required a light dose of 24 J cm^-2. The best effect of increasing the effectiveness of combating this pathogen was observed in the case of AlPcS₂ + AuNPs as a photosensitizing mixture. The light dose of 24 J cm^-2 caused a lethal effect of the studied coccus in the planktonic culture.

One-dimensional necklace-like assemblies of inorganic nanoparticles: Recent advances in design, preparation and applications

One-dimensional (1D) necklace-like assembly of inorganic nanoparticles exhibits unique collective properties, which are critical to open up new and remarkable opportunities in the field of nanotechnology. This review focuses on the recent advances in the production of these types of assemblies employing two strategies: colloidal synthesis and self-assembly procedures. After a brief description of the forces guiding nanoparticles towards the assembly, the main features of both strategies are discussed. Examples of approaches, typically involved in colloidal synthesis, are highlighted. The peculiar properties of 1D nanostructures are strictly associated with the nanoparticle arrangement in the form of highly ordered assemblies, which are attained during the synthesis both in the solution and using a template, as well as under the action of an external force. The various 1D necklace-like structures, created through nanoparticle self-assembly, demonstrate aligned, oriented nanoparticle organization. Diverse nature, size and shape of preformed particles as building blocks, along with utilizing different linkers, templates or external field lead to fabrication of 1D chain nanostructures with properties responsible for their wide applications. The unique structure-property relationship, both in colloidal synthesis, and self-assembly, offers broad spectrum of 1D necklace-like nanostructure implementations, illustrated by their use in photonics, electronics, electrocatalysis, magnetics.

Impact of the conjugation of antibodies to the surfaces of polymer nanoparticles on the immune cell targeting abilities

Antibodies have been widely used to provide targeting ability and to enhance bioactivity owing to their high specificity, availability, and diversity. Recent advances in biotechnology and nanotechnology permit site-specific engineering of antibodies and their conjugation to the surfaces of nanoparticles (NPs) in various orientations through chemical conjugations and physical adhesions. This study proposes the conjugation of poly(lactic-co-glycolic acid) (PLGA) NPs with antibodies by using two distinct methods, followed by a comparison between the cell-targeting efficiencies of both techniques. Full-length antibodies were conjugated to the PLGA-poly(ethylene glycol)-carboxylic acid (PLGA-PEG-COOH) NPs through the conventional carbodiimide coupling reaction, and f(ab')2 antibody fragments were conjugated to the PLGA-poly(ethylene glycol)-maleimide(PLGA-PEG-Mal) NPs through interactions between the f(ab')2 fragment thiol groups and the maleimide located on the nanoparticle surface. The results demonstrate that the PLGA nanoparticles conjugated with the f(ab')2 antibody fragments had a higher targeting efficiency in vitro and in vivo than that of the PLGA nanoparticles conjugated with the full-length antibodies. The results of this study can be built upon to design a delivery technique for drugs through biocompatible nanoparticles.

Multifunctional Gold Nanoparticles: A Novel Nanomaterial for Various Medical Applications and Biological Activities

Nanotechnology has become a trending area in science and has made great advances with the development of functional, engineered nanoparticles. Various metal nanoparticles have been widely exploited for a wide range of medical applications. Among them, gold nanoparticles (AuNPs) are widely reported to guide an impressive resurgence and are highly remarkable. AuNPs, with their multiple, unique functional properties, and easy of synthesis, have attracted extensive attention. Their intrinsic features (optics, electronics, and physicochemical characteristics) can be altered by changing the characterization of the nanoparticles, such as shape, size and aspect ratio. They can be applied to a wide range of medical applications, including drug and gene delivery, photothermal therapy (PTT), photodynamic therapy (PDT) and radiation therapy (RT), diagnosis, X-ray imaging, computed tomography (CT) and other biological activities. However, to the best of our knowledge, there is no comprehensive review that summarized the applications of AuNPs in the medical field. Therefore, in this article we systematically review the methods of synthesis, the modification and characterization techniques of AuNPs, medical applications, and some biological activities of AuNPs, to provide a reference for future studies.

Nonlinear Plasmonic Sensing for Label-Free and Selective Detection of Mercury at Picomolar Level

We present the concept of a nonlinear plasmonic sensing approach for rapid, sensitive, and label-free detection of mercury. Nonlinear plasmonic sensing of mercury relies on a systematic combination of nonlinear optics (NLO) with well-known concepts of amalgamation chemistry and plasmonic properties of gold nanorods. Exploiting the extreme sensitivity of the NLO process toward Hg-induced change in the local electric field of plasmonic nanorods, we succeed in improving the limit of detection (LOD) of mercury by 2-3 orders of magnitude as compared to the commonly used linear localized surface plasmon resonance (LSPR) based sensing. Using our method, an LOD of as low as 58 pM (11 ppt) has been achieved with high selectivity. Nonlinear plasmonic sensing aproach is found to work excellently for detecting mercury in real samples like blood plasma.

Electrochemical quantification of Ag2S quantum dots: evaluation of different surface coating ligands for bacteria determination

In this work, novel silver sulphide quantum dots (Ag₂S QD) are electrochemically quantified for the first time. The method is based on the electrochemical reduction of Ag⁺ to Ag⁰ at -0.3 V on screen-printed carbon electrodes (SPCEs), followed by anodic stripping voltammetric oxidation that gives a peak of currents at +0.06 V which represents the analytical signal. The optimized methodology allows the quantification of water-stabilized Ag₂S QD in the range of approximately 2 × 10⁹-2 × 10¹² QD·mL^-1 with a good reproducibility (RSD: 5%). Moreover, as proof-of-concept of relevant biosensing application, Ag₂S QD are evaluated as tags for Escherichia coli (E. coli) bacteria determination. Bacteria tagged with QD are separated by centrifugation from the sample solution and placed on the SPCE surface for quantitative analysis. The effect of two different Ag₂S QD surface coating/stabilizing agents on both the voltammetric response and the bacteria sensing is also evaluated. 3-mercaptopropionic acid (3-MPA) is studied as model of short length coating ligand with no affinity for the bacteria, while boronic acid (BA) is evaluated as longer length ligand with chemical affinity for the polysaccharides present in the peptidoglycan layer on the bacteria cells surface. The biosensing system allows to detect bacteria in the range 10^-1-10³ bacteria·mL^-1 with a limit of detection as low as 1 bacteria·mL^-1. This methodology is a promising proof-of-concept alternative to traditional laboratory-based tests, with good sensitivity and short time and low cost of analysis. Graphical abstractNovel silver sulphide quantum dots (Ag₂S QD) are electrochemically quantified for the first time. Moreover, Ag₂S QD are evaluated as tags for Escherichia coli bacteria determination. The effect of two different QD surface coating ligands is also evaluated.

Effects of treatment with gold nanoparticles in a model of acute pulmonary inflammation induced by lipopolysaccharide

The bacterial lipopolysaccharide (LPS) is a highly toxic molecule derived from the outer membrane of gram-negative bacteria. LPS endotoxin affects the lungs and is used as a model of acute pulmonary inflammation affecting the cellular morphology of the organ. Previously, gold nanoparticles (GNPs) have been shown to demonstrate anti-inflammatory and antioxidative activity in muscle and epithelial injury models. The objective of this study was to investigate the effect of the intraperitoneal treatment using GNPs on the inflammatory response and pulmonary oxidative stress induced by LPS. Wistar rats were divided into four groups (N = 10): Sham; Sham + GNPs 2.5 mg/kg; LPS; and LPS + GNPs 2.5 mg/kg. Treatment with LPS upregulated the levels of markers of cellular and hepatic damage (CK, LDH, AST, and alanine aminotransferase); however, the group treated with only GNPs exhibited no toxicity. Treatment with GNPs reversed LPS-induced changes with respect to total peritoneal leukocyte count and the pulmonary levels of pro-inflammatory cytokines (IFN-γ and IL-6). Histological analysis revealed that treatment with GNPs reversed the increase in alveolar septum thickness due to LPS-induced fibrosis. In addition, treatment with GNPs decreased production of oxidants (nitrite and DCFH), reduced oxidative damage (carbonyl and sulfhydryl), and downregulated activities of superoxide dismutase and catalase. Treatment with GNPs did not showed toxicity; however, it exhibited anti-inflammatory and antioxidative activity that reversed morphological alterations induced by LPS.

Impact of conjugation strategies for targeting of antibodies in gold nanoparticles for ultrasensitive detection of 17β-estradiol

Antibody-coated nanoparticles have recently attracted considerable attention, with the focus falling on diagnostics. Nevertheless, controlled antibody bioconjugation remains a challenge. Here, we present two strategies of bioconjugation with the aim of evaluating the best approach for the coupling of antibodies on the surface of nanomaterials in an oriented way. We employed electrostatic interaction (physical adsorption) and covalent conjugation in the orientation of antibodies on the metallic surface as coupling methods, and their influence on the detection of 17β-estradiol was addressed with localized surface plasmon resonance. The understanding of these mechanisms is fundamental for the development of reproducible inorganic bioconjugates with oriented surface as well sensibility of immunoassays.

Multifunctionality of gold nanoparticles: Plausible and convincing properties

In a couple of decades, nanotechnology has become a trending area in science due to it covers all subject that combines diverse range of fields including but not limited to chemistry, physics and medicine. Various metal and metal oxide nanomaterials have been developed for wide range applications. However, the application of gold nanostructures and nanoparticles has been received more attention in various biomedical applications. The unique property of gold nanoparticles (AuNPs) is surface plasmon resonance (SPR) that determine the size, shape and stability. The wide surface area of AuNPs eases the proteins, peptides, oligonucleotides, and many other compounds to tether and enhance the biological activity of AuNPs. AuNPs have multifunctionality including antimicrobial, anticancer, drug and gene delivery, sensing applications and imaging. This state-of-the-art review is focused on the role of unique properties of AuNPs in multifunctionality and its various applications.

Using near-infrared enhanced thermozyme and scFv dual-conjugated Au nanorods for detection and targeted photothermal treatment of Alzheimer's disease

Investigation of targeting inhibitors of Aβ aggregation, heme-Aβ peroxidase-like activity and efficient detectors of Aβ aggregation, are of therapeutic value and diagnostics significance for the treatment of Alzheimer's disease (AD). Due to the complex pathogenesis of AD, theranostics treatment with multiple functions are necessary. Herein we constructed the NIR absorption property of gold nanorods (GNRs) loaded with single chain variable fragment (scFv) 12B4 and thermophilic acylpeptide hydrolase (APH) ST0779 as a smart theranostic complex (GNRs-APH-scFv, GAS), which possesses both rapid detection of Aβ aggregates and NIR photothermal treatment that effectively disassembles Aβ aggregates and inhibits Aβ-mediated toxicity.

Methods: We screened targeting anti-Aβ scFv 12B4 and thermophilic acylpeptide hydrolase as amyloid-degrading enzyme, synthesized GAS gold nanorods complex. The GAS was evalued by Aβ inhibition and disaggregation assays, Aβ detection assays, Aβ mediated toxicity assays in vitro. In vivo, delaying Aβ-induced paralysis in AD model of Caenorhabditis elegans was also tested by GAS.

Results: In vitro, GAS has a synergistic effect to inhibit and disassociate Aβ aggregates, in addition to decrease heme-Aβ peroxidase-like activity. In cultured cells, treatment with GAS reduces Aβ-induced cytotoxicity, while also delaying Aβ-mediated paralysis in CL4176 C.elegans model of AD. Furthermore, the photothermal effect of the GAS upon NIR laser irradiation not only helps disassociate the Aβ aggregates but also boosts APH activity to clear Aβ. The GAS, as a targeting detector and inhibitor, allows real-time detection of Aβ aggregates.

Conclusion: These results firstly highlight the combination of scFv, APH and nanoparticles to be theranostic AD drugs. Taken together, our strategy provides a new thought into the design of smart compounds for use as efficiently therapeutic and preventive agents against AD. Moreover, our design provides broad prospects of biomedical strategy for further theranostics application in those diseases caused by abnormal protein.

A sensitive gold-nanorods-based nanobiosensor for specific detection of Campylobacter jejuni and Campylobacter coli

BACKGROUND

Campylobacteriosis is a zoonotic infectious disease that can be mostly undiagnosed or unreported due to fastidious Campylobacter species. The aim of this study was to develop a simple, sensitive, and quick assay for the detection of Campylobacter spp. and taking advantage of the great sensitivity of gold nanorods (GNRs) to trace changes in the local environment and interparticle distance.

METHODS

Characterized GNRs were modified by specific ssDNA probes of cadF gene. First, the biosensor was evaluated using recombinant plasmid (pTG19-T/cadF) and synthetic single-stranded 95 bp gene, followed by a collection of the extracted DNAs of the stool samples. The sensing strategy was compared by culture, PCR, and real-time PCR.

RESULTS AND DISCUSSION

Analysis of 283 specimens showed successful detection of Campylobacter spp. in 44 cases (16%), which was comparable to culture (7%), PCR (15%), and real-time PCR (18%). In comparison with real-time PCR, the sensitivity of the biosensor was reported 88%, while the specificity test for all assays was the same (100%). However, it was not able to detect Campylobacter in 6 positive clinical samples, as compared to real-time PCR. The limit of detection was calculated to be the same for the biosensor and real-time PCR (10² copy number/mL).

CONCLUSIONS

Taking high speed and simplicity of this assay into consideration, the plasmonic nanobiosensor could pave the way in designing a new generation of diagnostic kits for detection of C. jejuni and C. coli species in clinical laboratories.

Detecting Biothreat Agents: From Current Diagnostics to Developing Sensor Technologies

Although a fundamental understanding of the pathogenicity of most biothreat agents has been elucidated and available treatments have increased substantially over the past decades, they still represent a significant public health threat in this age of (bio)terrorism, indiscriminate warfare, pollution, climate change, unchecked population growth, and globalization. The key step to almost all prevention, protection, prophylaxis, post-exposure treatment, and mitigation of any bioagent is early detection. Here, we review available methods for detecting bioagents including pathogenic bacteria and viruses along with their toxins. An introduction placing this subject in the historical context of previous naturally occurring outbreaks and efforts to weaponize selected agents is first provided along with definitions and relevant considerations. An overview of the detection technologies that find use in this endeavor along with how they provide data or transduce signal within a sensing configuration follows. Current "gold" standards for biothreat detection/diagnostics along with a listing of relevant FDA approved in vitro diagnostic devices is then discussed to provide an overview of the current state of the art. Given the 2014 outbreak of Ebola virus in Western Africa and the recent 2016 spread of Zika virus in the Americas, discussion of what constitutes a public health emergency and how new in vitro diagnostic devices are authorized for emergency use in the U.S. are also included. The majority of the Review is then subdivided around the sensing of bacterial, viral, and toxin biothreats with each including an overview of the major agents in that class, a detailed cross-section of different sensing methods in development based on assay format or analytical technique, and some discussion of related microfluidic lab-on-a-chip/point-of-care devices. Finally, an outlook is given on how this field will develop from the perspective of the biosensing technology itself and the new emerging threats they may face.

A Colorimetric Probe Based on Functionalized Gold Nanorods for Sensitive and Selective Detection of As(III) Ions

A colorimetric probe for determination of As(III) ions in aqueous solutions on basis of localized surface plasmon resonance (LSPR) was synthesized. The dithiothreitol molecules with two end thiols covalently combined with Au Nanorods (AuNRs) with an aspect ratio of 2.9 by Au-S bond to form dithiothreitol coated Au Nanorods (DTT-AuNRs), acting as colorimetric probe for the determination of As(III) ions. With the adding of As(III) ions, the AuNRs will be aggregated and leading the longitudinal SPR absorption band of DTT-AuNRs decrease due to the As(III) ions can bind with three DTT molecules through an As-S linkage. The potential factors affect the response of DTT-AuNRs to As(III) ions including the concentration of DTT, pH values of DTT-AuNRs, reaction time and NaCl concentration were optimized. Under optimum assay conditions, the DTT-AuNRs colorimetric probe has high sensitivity towards As(III) ions with low detection limit of 38 nM by rules of 3σ/k and excellent linear range of 0.13–10.01 μM. The developed colorimetric probe shows high selectivity for As(III) ions sensing and has applied to determine of As(III) in environmental water samples with quantitative spike-recoveries range from 95.2% to 100.4% with low relative standard deviation of less than 4.4% (n = 3).

Biosensors for wastewater monitoring: A review

Water pollution and habitat degradation are the cause of increasing water scarcity and decline in aquatic biodiversity. While the freshwater availability has been declining through past decades, water demand has continued to increase particularly in areas with arid and semi-arid climate. Monitoring of pollutants in wastewater effluents are critical to identifying water pollution area for treatment. Conventional detection methods are not effective in tracing multiple harmful components in wastewater due to their variability along different times and sources. Currently, the development of biosensing instruments attracted significant attention because of their high sensitivity, selectivity, reliability, simplicity, low-cost and real-time response. This paper provides a general overview on reported biosensors, which have been applied for the recognition of important organic chemicals, heavy metals, and microorganisms in dark waters. The significance and successes of nanotechnology in the field of biomolecular detection are also reviewed. The commercially available biosensors and their main challenges in wastewater monitoring are finally discussed.

Bifunctional linker-based immunosensing for rapid and visible detection of bacteria in real matrices

Detection of pathogens present in food and water is essential to help ensure food safety. Among the popular methods for pathogen detection are those based on culture and colony-counting and polymerase chain reaction (PCR). However, the time-consuming nature and/or the need for sophisticated instrumentation of those methods limit their on-site applications. We have developed a rapid and highly sensitive immunosensing method for visible detection of bacteria in real matrices based on the aggregation of AuNPs without requiring any readout device. We use biotinylated anti-bacteria antibodies as bifunctional linkers (BLs) to mediate the aggregation of streptavidin-functionalized gold nanoparticles (st-AuNPs) to produce visually recognizable color change, due to surface plasmon resonance (SPR), which occurs in about 30min of total assay time when the sample is mildly agitated or within three hours in quiescent conditions. The aggregation of st-AuNPs, which produces the indication signal, is achieved very differently than in visual detection methods reported previously and hence affords ultrahigh sensitivity. While BLs can both bind to the target and crosslink st-AuNPs, their latter function is essentially disabled when they bind to the target bacteria. By varying the amount of st-AuNPs used, we can tailor the assay effectiveness improving limit of detection (LOD) down to 10CFUmL^-1 of E. coli and Salmonella. Test results obtained with tap water, lake water and milk samples show that assay performance is unaffected by matrix effects. Further, in a mixture of live and autoclaved E. coli cells our assay could detect only live cells. Therefore, our BL-based immunosensor is suitable for highly sensitive, rapid, and on-site detection of bacteria in real matrices.

Multifunctional Nanotechnology-Enabled Sensors for Rapid Capture and Detection of Pathogens

Nanomaterial-based sensing approaches that incorporate different types of nanoparticles (NPs) and nanostructures in conjunction with natural or synthetic receptors as molecular recognition elements provide opportunities for the design of sensitive and selective assays for rapid detection of contaminants. This review summarizes recent advancements over the past ten years in the development of nanotechnology-enabled sensors and systems for capture and detection of pathogens. The most common types of nanostructures and NPs, their modification with receptor molecules and integration to produce viable sensing systems with biorecognition, amplification and signal readout are discussed. Examples of all-in-one systems that combine multifunctional properties for capture, separation, inactivation and detection are also provided. Current trends in the development of low-cost instrumentation for rapid assessment of food contamination are discussed as well as challenges for practical implementation and directions for future research.

Theranostic Gold Nanoantennas for Simultaneous Multiplexed Raman Imaging of Immunomarkers and Photothermal Therapy

In this study, we demonstrate the theranostic capability of actively targeted, site-specific multibranched gold nanoantennas (MGNs) in triple-negative breast cancer (TNBC) cells in vitro. By utilizing multiplexed surface-enhanced Raman scattering (SERS) imaging, enabled by the narrow peak widths of Raman signatures, we simultaneously targeted immune checkpoint receptor programmed death ligand 1 (PDL1) and the epidermal growth factor receptor (EGFR) overexpressed in TNBC cells. A 1:1 mixture of MGNs functionalized with anti-PDL1 antibodies and Raman tag 5,5-dithio-bis-(2-nitrobenzoic acid) (DTNB) and MGNs functionalized with anti-EGFR antibodies and Raman tag para-mercaptobenzoic acid (pMBA) were incubated with the cells. SERS imaging revealed a cellular traffic map of MGN localization by surface binding and receptor-mediated endocytosis, enabling targeted diagnosis of both biomarkers. Furthermore, cells incubated with anti-EGFR-pMBA-MGNs and illuminated with an 808 nm laser for 15 min at 4.7 W/cm² exhibited photothermal cell death only within the laser spot (indicated by live/dead cell fluorescence assay). Therefore, this study not only provides an optical imaging platform that can track immunomarkers with spatiotemporal control but also demonstrates an externally controlled light-triggered therapeutic approach enabling receptor-specific treatment with biocompatible theranostic nanoprobes.

Using Multifunctional Peptide Conjugated Au Nanorods for Monitoring β-amyloid Aggregation and Chemo-Photothermal Treatment of Alzheimer's Disease

Development of sensitive detectors of Aβ aggregates and effective inhibitors of Aβ aggregation are of diagnostic importance and therapeutic implications for Alzheimer's disease (AD) treatment. Herein, a novel strategy has been presented by self-assembly of peptide conjugated Au nanorods (AuP) as multifunctional Aβ fibrillization detectors and inhibitors. Our design combines the unique high NIR absorption property of AuNRs with two known Aβ inhibitors, Aβ15-20 and polyoxometalates (POMs). The synthesized AuP can effectively inhibit Aβ aggregation and dissociate amyloid deposits with NIR irradiation both in buffer and in mice cerebrospinal fluid (CSF), and protect cells from Aβ-related toxicity upon NIR irradiation. In addition, with the shape and size-dependent optical properties, the nanorods can also act as effective diagnostic probes to sensitively detect the Aβ aggregates. This is the first report to integrate 3 segments, an Aβ-targeting element, a reporter and inhibitors, in one drug delivery system for AD treatment.

Direct, label-free, selective, and sensitive microbial detection using a bacteriorhodopsin-based photoelectric immunosensor

A photoelectric immunosensor using purple membranes (PM) as the transducer, which contains photoactive bacteriorhodopsin, is here first demonstrated for direct and label-free microbial detection. Biotinylated polyclonal antibodies against Escherichia coli were immobilized on a PM-coated electrode through further surface biotinylation and bridging avidin or NeutrAvidin. The photocurrent generated by the antibody-coated sensor was reduced after incubation with E. coli K-12 cultures, with the reduction level increased with the culture populations. The immunosensor prepared via NeutrAvidin exhibited much better selectivity than the one prepared via avidin, recognizing almost none of the tested Gram-positive bacteria. Cultures with populations ranging from 1 to 10⁷CFU/10mL were detected in a single step without any preprocessing. Both AFM and Raman analysis confirmed the layer-by-layer fabrication of the antibody-coated substrates as well as the binding of microorganisms. By investigating the effect of illumination orientation and simulating the photocurrent responses with an equivalent circuit model containing a chemical capacitance, we suggest that the photocurrent reduction was primarily caused by the light-shielding effect of the captured bacteria. Using the current fabrication technique, versatile bacteriorhodopsin-based photoelectric immunosensors can be readily prepared to detect a wide variety of biological cells.

Integrating recognition elements with nanomaterials for bacteria sensing

Pathogenic bacterial contamination is a major threat to human health and safety. In this review, we summarize recent strategies for the integration of recognition elements with nanomaterials for the detection and sensing of pathogenic bacteria. Nanoprobes can provide sensitive and specific detection of bacterial cells, which can be applied across multiple applications and industries.

Optimization of Nanoparticle-Based SERS Substrates through Large-Scale Realistic Simulations

Surface-enhanced Raman scattering (SERS) has become a widely used spectroscopic technique for chemical identification, providing unbeaten sensitivity down to the single-molecule level. The amplification of the optical near field produced by collective electron excitations -plasmons- in nanostructured metal surfaces gives rise to a dramatic increase by many orders of magnitude in the Raman scattering intensities from neighboring molecules. This effect strongly depends on the detailed geometry and composition of the plasmon-supporting metallic structures. However, the search for optimized SERS substrates has largely relied on empirical data, due in part to the complexity of the structures, whose simulation becomes prohibitively demanding. In this work, we use state-of-the-art electromagnetic computation techniques to produce predictive simulations for a wide range of nanoparticle-based SERS substrates, including realistic configurations consisting of random arrangements of hundreds of nanoparticles with various morphologies. This allows us to derive rules of thumb for the influence of particle anisotropy and substrate coverage on the obtained SERS enhancement and optimum spectral ranges of operation. Our results provide a solid background to understand and design optimized SERS substrates.

Hollow Au loaded with kanamycin for pharmacological and laser-triggered photothermal sterilization

Anti-E. coli-conjugated and kanamycin-loaded hAuNPs (hAuNPs-anti-E. coli-kana) were prepared for sterilization.

Nanomaterials-based biosensors for detection of microorganisms and microbial toxins

Detection of microorganisms and microbial toxins is important for health and safety. Due to their unique physical and chemical properties, nanomaterials have been extensively used to develop biosensors for rapid detection of microorganisms with microbial cells and toxins as target analytes. In this paper, the design principles of nanomaterials-based biosensors for four selected analyte categories (bacteria cells, toxins, mycotoxins, and protozoa cells), closely associated with the target analytes' properties is reviewed. Five signal transducing methods that are less equipment intensive (colorimetric, fluorimetric, surface enhanced Raman scattering, electrochemical, and magnetic relaxometry methods) is described and compared for their sensory performance (in term oflimit of detection, dynamic range, and response time) for all analyte categories. In the end, the suitability of these five sensing principles for on-site or field applications is discussed. With a comprehensive coverage of nanomaterials, design principles, sensing principles, and assessment on the sensory performance and suitability for on-site application, this review offers valuable insight and perspective for designing suitable nanomaterials-based microorganism biosensors for a given application.

Nonlinear Plasmonic Sensing with Nanographene

Plasmons provide excellent sensitivity to detect analyte molecules through their strong interaction with the dielectric environment. Plasmonic sensors based on noble metals are, however, limited by the spectral broadening of these excitations. Here we identify a new mechanism that reveals the presence of individual molecules through the radical changes that they produce in the plasmons of graphene nanoislands. An elementary charge or a weak permanent dipole carried by the molecule are shown to be sufficient to trigger observable modifications in the linear absorption spectra and the nonlinear response of the nanoislands. In particular, a strong second-harmonic signal, forbidden by symmetry in the unexposed graphene nanostructure, emerges due to a redistribution of conduction electrons produced by interaction with the molecule. These results pave the way toward ultrasensitive nonlinear detection of dipolar molecules and molecular radicals that is made possible by the extraordinary optoelectronic properties of graphene.

Facile Synthesis of Au-Coated Magnetic Nanoparticles and Their Application in Bacteria Detection via a SERS Method

This study proposes a facile method for synthesis of Au-coated magnetic nanoparticles (AuMNPs) core/shell nanocomposites with nanoscale rough surfaces. MnFe2O4 nanoparticles (NPs) were first modified with a uniform polyethylenimine layer (2 nm) through self-assembly under sonication. The negatively charged Au seeds were then adsorbed on the surface of the MnFe2O4 NPs through electrostatic interaction for Au shell formation. Our newly developed sonochemically assisted hydroxylamine seeding growth method was used to grow the adsorbed gold seeds into large Au nanoparticles (AuNPs) to form a nanoscale rough Au shell. Au-coated magnetic nanoparticles (AuMNPs) were obtained from the intermediate product (Au seeds decorated magnetic core) under sonication within 5 min. The AuMNPs were highly uniform in size and shape and exhibited satisfactory surface-enhanced Raman scattering (SERS) activity and strong magnetic responsivity. PATP was used as a probe molecule to evaluate the SERS performance of the synthesized AuMNPs with a detection limit of 10(-9) M. The synthesized AuMNPs were conjugated with Staphylococcus aureus (S. aureus) antibody for bacteria capture and separation. The synthesized plasmonic AuNR-DTNB NPs, whose LSPR wavelength was adjusted to the given laser excitation wavelength (785 nm), were conjugated with S. aureus antibody to form a SERS tag for specific recognition and report of the target bacteria. S. aureus was indirectly detected through SERS based on sandwich-structured immunoassay, with a detection limit of 10 cells/mL. Moreover, the SERS intensity at Raman peak of 1331 cm(-1) exhibited a linear relationship to the logarithm of bacteria concentrations ranging from 10(1) cells/mL to 10(5) cells/mL.

Rapid and Selective Detection of Pathogenic Bacteria in Bloodstream Infections with Aptamer-Based Recognition

Sepsis and bacteremia are life-threatening clinical syndromes associated with significant patient morbidity and mortality. Rapid and sensitive detection of pathogenic bacteria is the key to improve patient survival rates. Herein, we have rationally constructed a simple aptamer-based capture platform to shorten the time needed for confirmation of bacterial bloodstream infection in clinical blood samples. This capture platform is made of a mesoporous TiO2-coated magnetic nanoparticle and is modified with target aptamer. It features excellent bacterial enrichment efficiency of about 80% even at low bacterial concentrations (10-2000 CFU mL(-1)). More importantly, the bacteria can be enriched within 2 h, and the time for bacterial identification is effectively shortened in comparison to the "gold standard" in clinical diagnosis of bloodstream infection. The aptamer-based capture platform may pave a way for the detection of biomarkers and find potential applications in disease diagnosis.

Glycan heterogeneity on gold nanoparticles increases lectin discrimination capacity in label-free multiplexed bioassays

The development of new analytical tools as point-of-care biosensors is crucial to combat the spread of infectious diseases, especially in the context of drug-resistant organisms, or to detect biological warfare agents. Glycan/lectin interactions drive a wide range of recognition and signal transduction processes within nature and are often the first site of adhesion/recognition during infection making them appealing targets for biosensors. Glycosylated gold nanoparticles have been developed that change colour from red to blue upon interaction with carbohydrate-binding proteins and may find use as biosensors, but are limited by the inherent promiscuity of some of these interactions. Here we mimic the natural heterogeneity of cell-surface glycans by displaying mixed monolayers of glycans on the surface of gold nanoparticles. These are then used in a multiplexed, label-free bioassay to create 'barcodes' which describe the lectin based on its binding profile. The increased information content encoded by using complex mixtures of a few sugars, rather than increased numbers of different sugars makes this approach both scalable and accessible. These nanoparticles show increased lectin identification power at a range of lectin concentrations, relative to single-channel sensors. It was also found that some information about the concentration of the lectins can be extracted, all from just a simple colour change, taking this technology closer to being a realistic biosensor.

Alizarin Dye based ultrasensitive plasmonic SERS probe for trace level Cadmium detection in drinking water

Alizarin functionalized on plasmonic gold nanoparticle displays strong surface enhanced Raman scattering from the various Raman modes of Alizarin, which can be exploited in multiple ways for heavy metal sensing purposes. The present article reports a surface enhanced Raman spectroscopy (SERS) probe for trace level Cadmium in water samples. Alizarin, a highly Raman active dye was functionalized on plasmonic gold surface as a Raman reporter, and then 3-mercaptopropionic acid, 2,6-Pyridinedicarboxylic acid at pH 8.5 was immobilized on the surface of the nanoparticle for the selective coordination of the Cd (II). Upon addition of Cadmium, gold nanoparticle provide an excellent hotspot for Alizarin dye and Raman signal enhancement. This plasmonic SERS assay provided an excellent sensitivity for Cadmium detection from the drinking water samples. We achieved as low as 10 ppt sensitivity from various drinking water sources against other Alkali and heavy metal ions. The developed SERS probe is quite simple and rapid with excellent repeatability and has great potential for prototype scale up for field application.

Direct experimental observation of salt induced aspect ratio tunable PFPT silver-nanowire formation: SERS-based ppt level Hg2+ sensing from ground water

A common salt induced aspect ratio tunable PFPT silver nanowire synthesis with a plausible explanation based on real-time direct experimental observation finds application as a potential assay for ppt level Hg(ii) sensing from ground water.

Optical Second Harmonic Generation in Plasmonic Nanostructures: From Fundamental Principles to Advanced Applications

Plasmonics has emerged as an important research field in nanoscience and nanotechnology. Recently, significant attention has been devoted to the observation and the understanding of nonlinear optical processes in plasmonic nanostructures, giving rise to the new research field called nonlinear plasmonics. This review provides a comprehensive insight into the physical mechanisms of one of these nonlinear optical processes, namely, second harmonic generation (SHG), with an emphasis on the main differences with the linear response of plasmonic nanostructures. The main applications, ranging from the nonlinear optical characterization of nanostructure shapes to the optimization of laser beams at the nanoscale, are summarized and discussed. Future directions and developments, made possible by the unique combination of SHG surface sensitivity and field enhancements associated with surface plasmon resonances, are also addressed.

Interactions of Bacterial Lipopolysaccharides with Gold Nanorod Surfaces Investigated by Refractometric Sensing

The interface between nanoparticles and bacterial surfaces is of great interest for applications in nanomedicine and food safety. Here, we demonstrate that interactions between gold nanorods and bacterial surface molecules are governed by the nanoparticle surface coating. Polymer-coated gold nanorod substrates are exposed to lipopolysaccharides extracted from Pseudomonas aeruginosa, Salmonella enterica and Escherichia coli, and attachment is monitored using localized surface plasmon resonance refractometric sensing. The number of lipopolysaccharide molecules attached per nanorod is calculated from the shift in the plasmon maximum, which results from the change in refractive index after analyte binding. Colloidal gold nanorods in water are also incubated with lipopolysaccharides to demonstrate the effect of lipopolysaccharide concentration on plasmon shift, ζ-potential, and association constant. Both gold nanorod surface charge and surface chemistry affect gold nanorod-lipopolysaccharide interactions. In general, anionic lipopolysaccharides was found to attach more effectively to cationic gold nanorods than to neutral or anionic gold nanorods. Some variation in lipopolysaccharide attachment is also observed between the three strains studied, demonstrating the potential complexity of bacteria-nanoparticle interactions.

Complete separation of macroscopic rod-like bimetallic nanoassembly perpendicular and parallel on substrate for simultaneous sensing of microorganisms

Although two kinds of macroscopic ordered tridimensional nanoassemblies, i.e., alignment of nanorods, can be yielded by controllable droplet evaporation methods, complete separation of the nanoassembly perpendicular or parallel to substrate is quite challenging. It can, however, be realized by the aid of facet blocking combined with the tuning of ionic strength and colloidal concentration. The as-fabricated rod-like bimetallic nanoassembly has proved to be an excellent SERS active substrate compared to random aggregates. It should be mentioned that macroscopic ordered tridimensional nanoassembly perpendicular to the substrate can be used as a highly active SERS substrate with good uniformity and can be successfully applied for finely discriminating two microorganisms: Escherichia coli bacteria and Saccharomycetes.