Advances in materials and concepts in fixed prosthodontics: a selection of possible treatment modalities

Survival, technical and biological outcome of fixed tooth- and implant-supported restorations: A retrospective analysis of a patient cohort treated in an undergraduate dental education program

OBJECTIVES

There is a paucity of data on the outcome of fixed tooth- and implant-supported porcelain-fused-to-metal (PFM) and ceramic-based (CB) restorations fabricated during undergraduate dental education. Therefore, this retrospective study examined the outcome of fixed restorations placed in patients participating in an undergraduate program.

METHODS

Patient records were searched for data on fixed PFM and CB restorations. For these restorations, the functional period in situ and technical and biological complications, namely restoration fracture, decementation, screw loosening, secondary caries, and loss of vitality, were recorded. Periodontal parameters were also documented. Kaplan-Meier survival and complication estimates after 1 and 5 years were calculated for restoration types, materials, designs (veneered/non-veneered), cementation/retention modes and localizations with group sizes ≥ 15. Regression models were used to analyze the influence of demographic data and abovementioned restoration characteristics on restoration survival, technical and biological outcome.

RESULTS

1196 restorations with a mean observation time of 5 years were included in the analysis. The different restoration types exhibited survival rates of > 90.8% after 5 years, accompanied by a favorable biological outcome. However, monolithic resin-matrix or feldspathic ceramic restorations were found to have a higher fracture rate than lithium disilicate or zirconium dioxide ceramic restorations resulting in lower survival rates for these restorations. Additionally, resin-matrix ceramic restorations showed a higher decementation rate than lithium disilicate restorations.

CONCLUSIONS

Fixed tooth- and implant-supported CB restorations fabricated from lithium disilicate and zirconium dioxide ceramics demonstrated better survival and lower complication rates than restorations fabricated from resin-matrix or feldspathic ceramics in an undergraduate dental education program.

CLINICAL SIGNIFICANCE

Due to the more favorable outcome of CB restorations fabricated from lithium disilicate or zirconium dioxide ceramics, undergraduate dental education should focus on the application of these ceramics to increase restoration survival by reducing technical complications.

Evaluation of Complications Associated with Fixed Partial Denture: A Prospective Study

Objective

To assess complications, survival rates, and patient-reported outcomes associated with fixed partial dentures (FPDs).

Methods

A cohort of 146 subjects, aged 18 and above, requiring FPD were recruited. Following comprehensive dental examinations, FPDs were fabricated. Complications, survival rates, and patient-reported outcomes were evaluated at 3, 6, 12, and 24 months.

Results

Complications such as marginal discrepancies and framework fractures showed low frequencies over short-, mid-, and long-term intervals. Survival rates were high at 98.6%, 96.2%, 93.7%, and 91.1% at all intervals, respectively. Patient-reported outcomes indicated a mean comfort level of 8.2 with speech difficulties (8.2%) and hygiene challenges (4.8%). Overall satisfaction was high, with a mean score of 9.0.

Conclusion

This study provided evidence of favorable outcomes with low complication rates, high survival rates, and positive patient-reported experiences associated with FPDs.

Recent advances in dental zirconia: 15 years of material and processing evolution

OBJECTIVES

The objective was to discuss the research on zirconia published in the past 15 years to help the dental materials community understand the key properties of the types of zirconia and their clinical applications.

METHODS

A literature search was performed in May/2023 using Web of Science Core Collection with the term "dental zirconia". The search returned 5102 articles, which were categorized into 31 groups according to the research topic.

RESULTS

The current approach to improving the translucency of zirconia is to decrease the alumina content while increasing the yttria content. The resulting materials (4Y-, 5Y-, and above 5 mol% PSZs) may contain more than 50% of cubic phase, with a decrease in mechanical properties. The market trend for zirconia is the production of CAD/CAM disks containing more fracture resistant 3Y-TZP at the bottom layers and more translucent 5Y-PSZ at the top. Although flaws located between layers in multilayered blocks might represent a problem, newer generations of zirconia layered blocks appear to have solved this problem with novel powder compaction technology. Significant advancements in zirconia processing technologies have been made, but there is still plenty of room for improvement, especially in the fields of high-speed sintering and additive manufacturing.

SIGNIFICANCE

The wide range of zirconia materials currently available in the market may cause confusion in materials selection. It is therefore imperative for dental clinicians and laboratory technicians to get the needed knowledge on zirconia material science, to follow manufacturers' instructions, and to optimize the design of the prosthetic restoration with a good understanding where to reinforce the structure with a tough and strong zirconia.

Durability of Resin Bonding to Dental 3Y-TZP Zirconia Using Different Adhesive Systems

This laboratory study was conducted to evaluate and compare the resin bond strength of different adhesive resin systems in different combinations and the durability of their bonds with zirconia ceramic.

MATERIALS AND METHODS

One hundred and twenty-eight specimens were milled from 3Y-TZP zirconia ceramic. The bonding surfaces of all disks were wet polished, steam cleaned, airborne-particle abraded and ultrasonically cleaned in 99% isopropanol. The specimens were randomly divided into four main groups according to the applied resin system; two conventional and two self-adhesive systems were used. Each group was further subdivided into two subgroups; the first was conditioned with the specified primer for conventional luting resins or not conditioned for the self-adhesive systems, whereas the second subgroup of each was conditioned with the same phosphate monomer-containing primer (Alloy Primer). The zirconia specimens were adhesively bonded, using the allocated luting resin, to plexiglass tubes filled with self-curing composite resin (Clearfil FII). Half of the specimens of each subgroup were stored in distilled water at 37 °C for 3 days, whereas the other half were subjected to artificial aging, 150 days of storage and additional thermal cycling. Thereafter, all specimens were subjected to TBS testing using a universal testing machine. Statistical analysis was conducted using two-way ANOVA followed by separate one-way ANOVAs. The Games-Howell post-hoc test was applied for pairwise comparisons.

RESULTS

All specimens survived storage with thermal cycling. The mean TBS values ranged from a minimum of 43.4 ± 5.0 MPa to a maximum of 66.4 ± 3.5 after 3 days and from a minimum of 13.6 ± 2.5 MPa to a maximum of 50.1 ± 9.4 MPa after 150 days.

CONCLUSIONS

Artificial aging had a significantly negative effect on all test groups. The chosen adhesive-resin system had a significant effect on the resulting TBS values. The highest TBS values were achieved for the self-adhesive luting resin G-Cem One but were statistically comparable to the results obtained for the dual-cure luting resin G-Cem LinkForce.

Indirect repair of saliva-contaminated materials using veneering ceramics

PURPOSE

To analyze the in vitro efficacy of a surface conditioning liquid facilitating ceramic repairs of saliva-contaminated metal-ceramic and all-ceramic restorations.

MATERIALS AND METHODS

Specimens constructed from non-precious alloy (NPA), precious alloy (PA), lithium-disilicate (LD), zirconia (ZI), veneering ceramics for zirconia (VZI), veneering ceramics for lithium-disilicate (VLD), and veneering ceramics for metal alloys (VM) were manufactured (total: n = 168; each material n = 24). Veneering ceramic cylinders (thickness: 2mm) were hand-layered on top of the specimens. Shear bond strength (SBS) tests were performed, measuring the maximum bond strength (MBS) of the cylinders on the specimens. Following this, the specimens were artificially aged and stored in artificial saliva for 30 days at 37°C. After physical cleaning using aluminum oxide air abrasion, a new surface conditioning liquid was applied (test, n = 84) or not (control, n = 84). New ceramic cylinders were hand-layered followed by a second SBS test. Descriptive statistics, linear regression analyses, and a one-sample t-test (α = 0.05) were used to ascertain the differences within (pre- vs. post-repair) and between the groups.

RESULTS

All specimens in the test group could be repaired, whereas 18 repairs in the control group failed. After the repairs, an MBS decrease was observed for the NPA specimens of the control group (-15.5MPa, p = 0.004) but not among any of the test groups. Comparing the change in MBS between the test and control groups, the reduction was significantly higher in the repaired NPA specimens of the control group (mean difference 11.8 MPa, p = 0.017).

CONCLUSIONS

Using the analyzed surface conditioning liquid, metal-ceramic and all-ceramic materials can be repaired, while some repairs failed without the liquid. The initial bond strengths between core and veneering materials could be restored in all specimens when the new surface conditioning liquid was applied. This article is protected by copyright. All rights reserved.

CAD/CAM Diagnostic Esthetic Functional Splint (DEFS) as a Removable Prototype to Evaluate the Final Prosthetic Rehabilitation: A Narrative Review

The main objective of this narrative review was to provide an overview of DEFS (Diagnostic Esthetic Functional Splint), namely CAD/CAM manufactured, “snap-retained”, tooth-colored splints available by materials exhibiting a certain degree of elasticity (like polycarbonates or acetal resins) for restoring function, esthetics and occlusion in several clinical situations, before or as an intermediate alternative to undergoing the final treatment. The search strategy included all papers dealing with snap-retained prosthetic systems and was based on a literature review of papers available in electronic databases (Pubmed/Medline, Evidence-Based Dentistry, BMJ Evidence-Based Medicine, Dynamed, Embase, BMJ Clinical Evidence, Web of Science, Scientific reports); eligible papers were researched on Opengreyand a manual search was performed, as well. From the electronic databases emerged 13,199 records, many of which were duplicates. The grey literature and the manual research did not produce any eligible article. After duplicates removal, 7690 records were obtained. Titles, abstracts and keywords were analyzed. The studies concerning the topic of interest were examined by the reviewers and discussed. Although no evidence-based data were found in the literature, according to the authors’ clinical experience, the DEFS (Diagnostic Esthetic Functional Splint) is a very promising solution in multiple clinical situations, due to its diagnostic, therapeutical, functional and esthetic versatility.

Time-dependent degree of conversion, Martens parameters, and flexural strength of different dual-polymerizing resin composite luting materials

Objective

To investigate the degree of conversion (DC), Martens hardness (HM), elastic indentation modulus (E_IT), and biaxial flexural strength (BFS) of six dual-polymerizing resin composite luting materials initially and after 2 and 7 days of aging.

Materials and methods

Specimens fabricated from Bifix QM (BIF; VOCO), Calibra Ceram (CAL; Dentsply Sirona), DuoCem (DUO; Coltène/Whaledent), G-CEM LinkForce (GCE; GC Europe), PANAVIA V5 (PAN; Kuraray Europe), and Variolink Esthetic DC (VAR; Ivoclar Vivadent) (n = 12 per material) were light-polymerized through 1 mm thick discs (Celtra Duo, Dentsply Sirona). DC, HM, and E_IT were recorded directly after fabrication, and after 2 and 7 days of aging. As a final test, BFS was measured. Univariate ANOVAs, Kruskal–Wallis, Mann–Whitney U, Friedman, and Wilcoxon tests, and Weibull modulus were computed (p < 0.05).

Results

While CAL presented low DC, HM, E_IT, and BFS values, DUO and BIF showed high results. Highest Weibull moduli were observed for VAR and DUO. DC and Martens parameters increased between the initial measurement and 2 days of aging, while aging for 7 days provided no further improvement.

Conclusions

The choice of dual-polymerizing resin composite luting material plays an important role regarding chemical and mechanical properties, especially with patients sensitive to toxicological issues. DUO may be recommended for bonding fixed dental prostheses, as it demonstrated significantly highest and reliable results regarding DC, HM, and BFS. As DC and HM showed an increase in the first 48 h, it may be assumed that the polymerization reaction is not completed directly after initial polymerization, which is of practical importance to dentists and patients.

Clinical relevance

The chemical and mechanical properties of dual-polymerizing resin composite luting materials influence the overall stability and long-term performance of the restoration.

Influence of different cleaning procedures on the shear bond strength of 10-methacryloyloxydecyl dihydrogen phosphate-containing self-adhesive resin cement to saliva contaminated zirconia

PURPOSE

To evaluate the effect of different cleaning methods on the shear bond strength (SBS) of a 10-methacryloyloxydecyl dihydrogen phosphate (MDP)-containing self-adhesive resin cement to zirconia after saliva contamination.

METHODS

Sixty zirconia specimens were randomly divided into four groups (n=15) according to treatment surface. Except for the control group, all samples were contaminated with saliva and were then rinsed with water-spray and air-dried. Subsequently, the specimens were either treated with a cleaning paste (CP), with argon plasma (AP), or did not undergo an additional cleaning process (WS). An MDP-containing self-adhesive resin cement was applied onto the ceramic surfaces. Specimens were stored in water (24 hours) followed by thermocycling (5°C to 55°C for 10.000 cycles). SBS tests were performed in a universal testing machine, and the results (MPa ± SD) were statistically analyzed using ANOVA and Bonferroni post-hoc test. Fractured surfaces were examined to identify the failure types using a stereomicroscopy and SEM.

RESULTS

The surface cleaning treatment (p < 0.05) significantly affected the results. The highest SBS values were observed in the control group (12.16 ± 1.22 MPa) and were statistically comparable to values for the CP group (11.38 ± 1.65 MPa). The AP group (9.17 ± 1.06 MPa) showed significantly higher bond strength than the WS group (6.95 ± 1.20 MPa), but it showed significantly lower strength than the control and CP groups.

CONCLUSIONS

The CP application was the most effective method in removing saliva contamination. The AP treatment could not restore the SBS to the same level as uncontaminated specimens.

Biomechanical planning for minimally invasive indirect restorations

This paper explores the planning and execution of indirect partial-coverage restorations and will outline practical recommendations for maximising the outcomes for minimally invasive (MI) approaches to indirect restorations, with a special focus on vital teeth, endodontically-treated teeth and worn dentitions. Throughout the paper, the supporting evidence for each rationale for partial-coverage restorations will be considered, as well as the risks and benefits of adopting an MI approach to indirect restorations.

Clinical acceptability of PEEK fixed dental prosthesis in partially edentulous patient - A one year single arm pilot study

Purpose

The study evaluated the clinical efficacy of Polyether ether ketone (PEEK) fixed dental prosthesis (FDP) over a period of one year using modified Ryges criteria and California Dental Assessment system.

Methods

The group consisted of 20 patients restored with posterior three-unit PEEK FDP. Patient recall and clinical examination of the restorations were done at interval of 0, 3, 6, 9 and 12 months. Clinical examination for evaluation of longevity of restorations was done using modified Ryges criteria and California dental assessment system on chipping of the veneered composite, discoloration at the marginal areas, and marginal adaptation, retention, periodontal health and hygiene of PEEK FDP. Radiographic assessment was done after 12 months. Statistical analysis were done using Friedman test.

Results

95% of the patients had maintained the restoration of PEEK FDP without fracture during the study period. 5% patient reported with de-cementation of fixed dental prosthesis. 10% of the PEEK FDP shows marginal discoloration. However, no significant changes were observed during the periodic time interval evaluation in marginal adaptation, oral hygiene status and periodontal health. (p < 0.5).

Conclusion

PEEK FDP had satisfactory clinical efficacy and acceptable clinical outcome during the observation period of 12 months. No significant radiological changes were observed at the end of 12 months.

Material selection for tooth-supported single crowns-a survey among dentists in Germany

Objectives

This study aimed to survey dentists in Germany to identify their favored materials for the fabrication of tooth-supported single crowns (SCs) depending on the location of the abutment teeth and the preparation margin.

Materials and methods

The survey included questions regarding demographic characteristics of dentists/their dental practice and preferred restorative materials for the fabrication of SCs for abutment teeth 16, 11, 34, and 36 with either supra- or subgingival preparation margins.

Results

Between August 2019 and February 2020, 721 dentists participated in the survey; responses from 33 dentists were excluded from data analysis because the dentists did not work in Germany or provided less than one fixed dental prosthesis/month. Dentists favored ceramic materials independent of the location of the abutment tooth and preparation margin (56.6–92.2%). CAD/CAM resin composites or full metals were preferred by only a few participants. A significantly higher proportion of dentists recommended porcelain fused to metal for subgingival preparation margins than for supragingival margins (p < 0.001). Characteristics of dentists/dental practices influenced a single scenario (11 subgingival) that was dependent on the dentist’s time since graduation. When asked to specify the ceramic materials, numerous participants wrote a free response (5.7–7.8%) or did not answer (0.7–4.8%).

Conclusions

Dentists in Germany selected restorative materials for SCs depending on the clinical scenario. Since numerous dentists did not specify the ceramic materials, postgraduate information and education might help to extend expertise.

Clinical relevance

The results of this survey provide insight into the favored materials of dentists for the fabrication of tooth-supported SCs.

Radiopacity of computer-aided design/computer-aided manufacturing composite resin blocks

This study aimed to clarify the degree of difference in radiopacity between sixteen CAD/CAM composite resin blocks, one ceramic block, and teeth of the same thickness on radiographs. The radiographic density of CAD/CAM composite resin blocks was measured and the results were compared with the corresponding values for enamel and dentin. Additionally, the study analyzed the constituent elements of each type of CAD/CAM composite resin block and conducted an examination to identify those elements exerting an influence on radiopacity. Compared to the enamel, there were five blocks with significantly higher radiopacity, two blocks with the same level in radiopacity, and ten blocks with notably lower radiopacity. Compared to the dentin, there were ten blocks with significantly higher radiopacity, one block with the same level in radiopacity, and six blocks with notably lower radiopacity. All of the CAD/CAM composite resin blocks for molars contained barium and strontium. This result suggests that the addition of heavy metals, for example, barium, strontium, and zirconium, would be effective in providing CAD/CAM composite resin blocks with radiopacity.