Fabrication trueness and marginal quality of additively manufactured resin-based definitive laminate veneers with different restoration thicknesses

OBJECTIVES

To evaluate how restoration thickness (0.5 mm and 0.7 mm) affects the fabrication trueness of additively manufactured definitive resin-based laminate veneers, and to analyze the effect of restoration thickness and margin location on margin quality.

METHODS

Two maxillary central incisors were prepared either for a 0.5 mm- or 0.7 mm-thick laminate veneer. After acquiring the partial-arch scans of each preparation, laminate veneers were designed and stored as reference data. By using these reference data, a total of 30 resin-based laminate veneers were additively manufactured (n = 15 per thickness). All veneers were digitized and stored as test data. The reference and test data were superimposed to calculate the root mean square values at overall, external, intaglio, and marginal surfaces. The margin quality at labial, incisal, mesial, and distal surfaces was evaluated. Fabrication trueness at each surface was analyzed with independent t-tests, while 2-way analysis of variance was used to analyze the effect of thickness and margin location on margin quality (α = 0.05).

RESULTS

Regardless of the evaluated surface, 0.7 mm-thick veneers had lower deviations (P < 0.001). Only the margin location (P < 0.001) affected the margin quality as labial margins had the lowest quality (P < 0.001).

CONCLUSION

Restoration thickness affected the fabrication trueness of resin-based laminate veneers as 0.7 mm-thick veneers had significantly higher trueness. However, restoration thickness did not affect the margin quality and labial margins had the lowest quality.

CLINICAL SIGNIFICANCE

Laminate veneers fabricated by using tested urethane-based acrylic resin may require less adjustment when fabricated in 0.7 mm thickness. However, marginal integrity issues may be encountered at the labial surface.

One-Piece Mini Dental Implant-Retained Mandibular Overdentures: 10-Year Clinical and Radiological Outcomes of a Non-Comparative Longitudinal Observational Study

This study presents the first 10-year follow-up investigation of the implant survival and peri-implant outcomes of one-piece mini dental implants (MDIs) retaining mandibular implant overdentures (IODs), including marginal bone level alterations (ΔMBLs), clinical peri-implant parameters, and complications. Twenty participants with horizontally atrophied mandibles received complete dentures and four MDIs (diameter 1.8 mm) at baseline. The dentures were converted into IODs with O-ring attachments. The 10-year follow-up comprised a radiological assessment of ΔMBLs, peri-implant parameters, as well as biological and technical complications. Results from a 10-year follow-up of 14 participants showed a 100% implant survival rate for all 56 implants. The mean ΔMBL after 10 years was -1.12 ± 0.80 mm, with 49 implants classified as successful (ΔMBL < 2 mm) and 7 implants with satisfactory survival (ΔMBL 2-4 mm). Time after implant placement significantly influenced ΔMBL, with stable MBLs after 5 years. The prosthetic survival rate after 10 years was 93%. ΔMBLs were not influenced by implant position or gender but were significantly smaller in subjects older than 65 years. Conclusively, one-piece MDIs with O-ring attachments offer a reliable treatment option for horizontally atrophied mandibles after 10 years, with high implant and prosthetic survival rates, potentially benefiting from advanced age regarding peri-implant bone stability.

Effect of printing layer thickness on the trueness of 3-unit interim fixed partial dentures

STATEMENT OF PROBLEM

Three-dimensional printing has facilitated the fabrication processes in dentistry. However, knowledge on the effect of layer thickness on the trueness of 3D printed fixed partial dentures (FPDs) is lacking.

PURPOSE

The purpose of this in vitro study was to compare the effect of printing layer thickness on the trueness of 3-unit interim FPDs fabricated by using additive manufacturing with that of those fabricated by subtractive manufacturing.

MATERIAL AND METHODS

The right first premolar and first molar teeth of a dentate mandibular model were prepared for a 3-unit restoration and then digitized by using an intraoral scanner. A 3-unit interim FPD was designed to fabricate 40 restorations by using either the additive (NextDent C&B MFH) with layer thicknesses of 20 μm (n=10), 50 μm (n=10), and 100 μm (n=10) or subtractive manufacturing technique (Upcera) (milled, n=10). After fabrication, the interim FPDs were digitized by using the same intraoral scanner and were superimposed over the design data by using a 3D analysis software program. Root mean square (RMS) was used to analyze the trueness of the restorations at 4 different surfaces (external, intaglio, marginal area, and intaglio occlusal) and as a complete unit (overall). Data were analyzed with the Kruskal-Wallis and Wilcoxon tests with Bonferroni correction (α=.05).

RESULTS

The 100-μm-layer thickness interim FPDs showed the greatest overall (P≤.015), external (P≤.021), and intaglio occlusal (P≤.021) deviations, whereas the milled interim FPDs showed the lowest (P=.001). No significant differences were found among the test groups for marginal RMS (P≥.108). The differences between the 50-μm-layer thickness and 100-μm-layer thickness interim FPDs for the intaglio surface deviations (P=.064) and between the 20-μm-layer thickness and 50-μm-layer thickness interim FPDs for each surface tested were not statistically significant (P≥.108).

CONCLUSIONS

The printing layer thickness had a significant effect on the trueness of the additively manufactured interim FPDs. However, subtractively manufactured interim FPDs presented higher trueness than those additively manufactured, regardless of the printing layer thickness.

Impact of the superimposition methods and the designated comparison area on accuracy analyses in dentate models

OBJECTIVES

To measure the impact of superimposition methods and the designated comparison area on accuracy analyses of dentate models using an ISO-recommended 3-dimensional (3D) metrology-grade inspection software (Geomagic Control X; 3D Systems; Rock Hill, South Carolina; USA).

MATERIALS AND METHODS

A dentate maxillary typodont scanned with a desktop scanner (E4; 3 Shape; Copenhagen; Denmark) and an intraoral scanner (Trios 4; 3 Shape; Copenhagen; Denmark) was used as reference. Eight groups were created based on the core features of each superimposition method: landmark-based alignment (G1); partial area-based alignment (G2); entire tooth area-based alignment (G3); double alignment combining landmark-based alignment with entire tooth area-based alignment (G4); double alignment combining partial area-based alignment with entire tooth area-based alignment (G5); initial automated quick pre-alignment (G6); initial automated precise pre-alignment (G7); and entire model area-based alignment (G8). Diverse variations of each alignment and two regions for accuracy analyses (teeth surface or full model surface) were tested, resulting in a total of thirty-two subgroups (n = 18). The alignment accuracy between experimental and reference meshes was quantified using root mean square (RMS) error as trueness and its repeatability as precision. The descriptive statistics, a factorial repeated measures analysis of variance (ANOVA) and a post hoc Tuckey multiple comparison tests were used to analyze the trueness, and precision (α = 0.05).

RESULTS

A total of 576 superimpositions were performed. The unique partial area-based superimposition method demonstrated the least precise alignment and was the sole group to exhibit a significant difference (p<.001). Automated initial pre-alignments demonstrated similar accuracy to other superimposition methods (p>.05). Double alignments did not result in accuracy improvement (p>.05). The designated comparison area displayed differences in both trueness (p<.001) and precision (p<.001), leading to an overall discrepancy of 8 ± 4 μm between selecting the teeth surface or full model surface.

CONCLUSIONS

The superimposition method choice within the tested software did not impact accuracy analyses, except when the alignment relies on a unique and reduced area, such as the palatal rugae, a single tooth, or three adjacent teeth on one side.

CLINICAL SIGNIFICANCE

The superimposition method choice within the tested ISO-recommended 3D inspection software did not impact accuracy analyses.

Load bearing capacity of 3-unit screw-retained implant-supported fixed dental prostheses with a mesial and distal cantilever on a single implant: A comparative in vitro study

OBJECTIVES

To assess the mechanical durability of monolithic zirconia implant-supported fixed dental prostheses (iFDP) design on one implant, with a distal and a mesial extension cantilever bonded to a titanium base compared to established designs on two implants.

MATERIALS AND METHODS

Roxolid Tissue level (TL), and tissue level x (TLX) implants were used to manufacture screw-retained 3-unit iFDPs (n = 60, n = 10 per group), with following configurations (X: Cantilever; I: Implant, T: Test group, C: Control group): T1: X-I-X (TL); T2: X-I-X (TLX); T3: I-I-X (TL); T4: I-I-X (TLX); C1: I-X-I (TL); C2: I-X-I (TLX). The iFDPs were thermomechanically aged and subsequently loaded until fracture using a universal testing machine. The failure load at first crack (Finitial) and at catastrophic fracture (Fmax) were measured and statistical evaluation was performed using two-way ANOVA and Tukey's post-hoc tests.

RESULTS

The mean values ranged between 190 ± 73 and 510 ± 459 N for Finitial groups, and between 468 ± 76 and 1579 ± 249 N for Fmax, respectively. Regarding Finitial, neither the implant type, nor the iFDP configuration significantly influenced measured failure loads (all p > 0.05). The choice of implant type did not show any significant effect (p > 0.05), while reconstruction design significantly affected Fmax data (I-I-Xa < X-I-Xb < I-X-Ic) (p < 0.05). The mesial and distal extension groups (X-I-X) showed fractures only at the cantilever extension site, while the distal extension group (I-I-X) showed one abutment and one connector fracture at the implant/reconstruction interface.

CONCLUSION

Results suggest that iFDPs with I-X-I design can be recommended regardless of tested implant type followed by the mesial and distal extension design on one implant abutment (X-I-X).

Effect of adhesive system, resin cement, heat-pressing technique, and thermomechanical aging on the adhesion between titanium base and a high-performance polymer

STATEMENT OF PROBLEM

Even though polyetheretherketone (PEEK) has become popular for various prosthetic indications, a standard adhesive protocol to bond the PEEK to titanium bases has not been yet established. How the heat-pressing technique performs in this respect is also not clear.

PURPOSE

The purpose of this in vitro study was to investigate the effect of an adhesive system-cement combination, the heat-pressing technique, and thermomechanical aging on the retention force between titanium bases and PEEK specimens.

MATERIAL AND METHODS

Sixty 9×11×20-mm PEEK specimens with a titanium base slot integrated into the design were milled to simulate an implant-supported PEEK framework for a cantilevered fixed prosthesis. The specimens were assigned to 8 groups (n=10) according to the titanium base primer (MKZ or Monobond) and resin cement (DTK or Multilink hybrid) used and with or without thermomechanical aging. Twenty PEEK specimens were directly heat-pressed on titanium bases, and half of the specimens were not subjected to thermomechanical aging (n=10). For nonaged groups, the PEEK specimen complex was tightened to an implant analog and secured on a custom-made pull-off device. Retention forces were measured by using the pull-off tensile test in a universal testing machine, and the maximum tensile bond strength (MPa) was calculated. The aged groups were subjected to 5000 cycles of thermal aging (5 °C to 55 °C), and the specimens were clamped to load the extension (cantilever) for 1 200 000 cycles with 120 N and 200 N at 1.5-Hz frequency. After aging, the pull-off test was performed for those specimens that survived thermomechanical aging. A nonparametric Kruskal-Wallis test was used to determine whether there was a difference among the groups, followed by pairwise Wilcoxon rank tests with Bonferroni correction. The Wilcoxon rank test was used to analyze the effect of thermomechanical aging in each adhesive system-cement or heat-press group (α=.05 for all tests).

RESULTS

None of the specimens failed during cyclic loading. According to the Kruskal-Wallis test, the effect of the PEEK-Ti base bonding technique on the retention force in the nonaged (P=.019) and thermomechanically aged groups was significant (P=.010). In the nonaged groups, the heat-pressing technique resulted in a higher retention force than when the specimens were bonded by using the Monobond-Multilink hybrid combination (P=.031). Thermomechanical aging did not significantly affect the results (P>.241). All failures were adhesive, with cement remaining only on the Ti-bases.

CONCLUSIONS

All bonding protocols tested resulted in a stable bond between PEEK and Ti-bases, as all specimens survived thermomechanical aging. The heat-pressing technique resulted in mean bond strength values similar to those obtained with the tested adhesive system-cement combinations with 1 exception; the nonaged heat-pressed groups presented higher bond strength than the Monobond-Multilink hybrid combination. Failure types indicated that the weaker bond was between the PEEK and the cements tested rather than between the titanium base and the cements, regardless of the adhesive system-cement combination.

An integration protocol for aligning intraoral scans to facial scans using the nasal geometry reference in a fully dentate patient

Advanced digital technologies have rapidly been integrated into prosthodontics to improve the digital workflow for prosthetic rehabilitation. The integration of 3D datasets acquired from various imaging sources such as intraoral scanners and facial optical scanners allows the creation of virtual patients to perform presurgical simulation and prosthetic rehabilitation. The presented technique introduced a straightforward protocol for aligning intraoral scans (Trios 4, 3Shape) to optical face scans (Face Hunter, Zirkonzahn) using a global best-fit algorithm of 3D evaluation software (GOM Inspect). Nasal geometry data were used as the matching reference to produce virtual dental patients. This integration protocol ensured that the intraoral scanner (Trios 4, 3Shape) was used not only to scan dental arches but also used effectively to scan the nose. These scans along with professional facial scans can be successfully aligned to produce virtual dental patients. As only a single fully dentate patient case with an alignment deviation of 243.6 µm was used, further research to evaluate the accuracy of this protocol is needed.

Implant-supported single all-ceramic crowns made from prefabricated (stock) or individualized CAD/CAM zirconia abutments: A 5 year randomized clinical trial

AIM

The aim of this randomized, prospective, and clinical multicenter study was to compare the overall clinical performance of two restorative options over a 5-year period: individualized CAD/CAM abutments veneered with a hand-layered ceramic, and prefabricated zirconium dioxide abutments veneered with press ceramic and inserted into a single edentulous gap in the anterior maxilla.

MATERIALS AND METHODS

Forty subjects were recruited from two universities: 20 from the University of XX and 20 from the University of XY. Each subject received an implant to restore a single edentulous gap in the maxillary anterior region (14-24 FDI). 20 patients were randomized into each Group. Group A received a one-piece single crown produced from a prefabricated zirconia abutment with pressed ceramic and Group B received an individualized CAD/CAM zirconia abutment with a hand-layered technique. After 5 years, the aesthetic and radiographic parameters were assessed.

RESULTS

Group A had four dropouts and one failure, resulting in a 95% survival rate and 95% success rate. Group B had two dropouts and two failures which resulted in a 90% survival rate and 90% success rate. No crestal bone level changes were observed, with a mean DIB of 0.06 mm in Group A and 0.09 mm in Group B. No statistically significant differences were present at baseline, 6 months, 1 year, 3 years, or 5 years for DIB values between time points and groups. Pink aesthetic score/white aesthetic score, Peri-Implant and Crown Index, and Implant Crown Aesthetic Index values were stable over time at all five points for both groups.

CONCLUSION

Both implant-supported restorative options represent a valuable treatment option for the restoration of implant crowns in the anterior maxilla.

CLINICAL SIGNIFICANCE

In general, the use of ceramic abutments in the anterior zone represents a valuable treatment procedure with both standardized and CAD/CAM individualized abutments and following the recommendations from the respective manufacturer(s).

Success and complication rates of non-precious alloy telescopic crowns in a general dental practice

OBJECTIVES

This retrospective, single-center, practice-based cohort study aimed to analyze factors associated with the success of removable partial dentures retained by telescopic crowns (TRPD).

MATERIALS AND METHODS

TRPD which were placed in a single practice of a practice-based research network were analyzed. Data from 139 patients (age (SD): 66 (11) years; 66 female) with 174 TRPD including 488 non-precious alloy telescopic crowns (TC) between 2004 and 2016 were included. TC without any technical complication were considered as successful, and as survived, if they were still in function at the last check-up. Multilevel Cox proportional hazard models were used to evaluate the association between clinical factors and time until failure.

RESULTS

Within a mean follow-up period (SD) of 4.2 (3.3) years (min-max: 1 day-12 years), 372 (76%) TC (AFR5years,TC-level: 5.0%) as well as 136 (87%) TRPD (AFR5years,TRPD-level: 5.1%) ("worst-case scenario") and 150 (86%) TRPD (AFR5years,TRPD-level: 3.4%) ("best-case scenario") were considered as successful. The main failure types were recementation (n = 39), endodontic treatment (n = 36), and extraction (n = 35). TC in male patients showed 1.6 times higher risk for failure than in female patients (95%CI: 1.1-2.4; p = 0.023). TC on premolars showed 2.2 times higher risk for failure than on incisors (95%CI: 1.1-5.0; p = 0.023) and TC in dentures with ≤ 3TC showed 2.1 times higher risk for failure than TC in dentures with > 3TC (1.3-3.4; p = 0.042). Furthermore, TC on the most distal tooth in an arch showed 2.4 times higher risk for failure than TC on a more mesial tooth (1.5-3.8; p < 0.001).

CONCLUSION

For removable partial dentures retained by telescopic crowns, high success rates could be found after up to 12 years. Patient-level and tooth-level factors were significantly associated with failure.

CLINICAL RELEVANCE

For removable partial dentures retained by telescopic crowns, high success rates could be found after up to 12 years. Patient-level and tooth-level factors were significantly associated with failure.

Trueness and precision of combined healing abutment scan body system scans at different sites of maxilla after multiple repositioning of the scan body

OBJECTIVES

To evaluate the accuracy of the scans of the combined healing abutment-scan body (CHA-SB) system located at different sites of the maxilla when SBs are replaced in between each scan.

METHODS

Three SBs were seated into HAs located at the central incisor, first premolar, and first molar sites of a maxillary model inside a phantom head, and the model was scanned extraorally (CEREC Primescan SW 5.2). This procedure was repeated with new SBs until a total of 10 scans were performed. Standard tessellation language files of CHA-SBs at each implant location were isolated, transferred into analysis software (Geomagic Control X), and superimposed over the proprietary library files to analyze surface (root mean square), linear, and angular deviations. Trueness and precision were evaluated with one-way analysis of variance and Tukey tests. The correlation between surface and angular deviations was analyzed with Pearson's correlation (α=0.05).

RESULTS

Molar implant scans had the highest surface and angular deviations (P≤.006), while central incisor implant scans had higher precision (surface deviations) than premolar implant scans (P=.041). Premolar implant scans had higher accuracy than central incisor implant scans on the y-axis (P≤.029). Central incisor implant scans had the highest accuracy on the z-axis (P≤.018). A strong positive correlation was observed between surface and angular deviations (r = 0.864, P<.001).

CONCLUSION

Central incisor implant scans mostly had high accuracy and molar implant scans mostly had lower trueness. SBs were mostly positioned apically; however, the effect of SB replacement can be considered small as measured deviations were similar to those in previous studies and the precision of scans was high.

CLINICAL SIGNIFICANCE

Repositioning of scan bodies into healing abutments would be expected to result in similar single crown positioning regardless of the location of the implant, considering high scan precision with the healing abutment-scan body system. The duration of the chairside adjustments of crowns in the posterior maxilla may be longer than those in the anterior region.

Inter- and intraindividual variability in virtual single-tooth implant positioning

OBJECTIVES

The purpose of this prospective study was to determine the inter- and intraindividual variability in virtual single-tooth implant positioning based on the level of expertise, specialty, total time spent, and the use of a prosthetic tooth setup.

MATERIALS AND METHODS

Virtual implant planning was performed on matched pre- and post-extraction intraoral scans (IOS), and cone-beam computed tomography scans of 15 patients. Twelve individual examiners, involving six novices and experts from oral surgery and prosthodontics positioned the implants, first based on anatomical landmarks utilizing only the post-extraction, and second with the use of the pre-extraction IOS as a setup. The time for implant positioning was recorded. After 1 month, all virtual plannings were performed again. The individual implant positions were superimposed to obtain 3D deviations using a software algorithm.

RESULTS

An interindividual variability with mean angular, crestal, and apical positional deviations of 3.8 ± 1.94°, 1.11 ± 0.55, and 1.54 ± 0.66 mm, respectively, was found. When assessing intraindividual variability, deviations of 3.28 ± 1.99°, 0.78 ± 0.46, and 1.12 ± 0.61 mm, respectively, were observed. Implants planned by experts exhibited statistically lower deviations compared to those planned by novices. Longer planning times resulted in lower deviations in the experts' group but not in the novices. Oral surgeons demonstrated lower crestal, but not angular and apical deviations than prosthodontists. The use of a setup only led to minor adjustments.

CONCLUSIONS

Substantial inter- and intraindividual variability exists during implant positioning utilizing specialized software planning. The level of expertise and the time invested influenced the deviations of the implant position during the planning sequence.

Positional accuracy during the sequence of static computer-assisted implant surgery in three alveolar ridge morphologies: An in vitro study

PURPOSE

This in vitro study aimed to assess the positional accuracy during the sequence of static computer-assisted implant surgery (sCAIS) according to the anatomical characteristics of the alveolar ridge.

MATERIAL AND METHODS

Maxillary bone models with six single tooth gaps including clinical scenarios of healed alveolar ridge (HR), single-rooted (SRS), and three-rooted socket (TRS) morphologies were used in this study. Positional deviations during implant placement procedures were evaluated after the pilot osteotomy (PD), final osteotomy (FD), and implant placement with respect to the pre-planned implant position by using a software package. ANOVA and post hoc analyses were performed.

RESULTS

A total of 90 implants were included in this study. Higher mean angular, crestal, and apical deviations were found after the PD and FD (3.5 ± 2.4°, 0.7 ± 0.3 mm, and 1.4 ± 0.8 mm versus 3.6 ±2.2°, 0.6 ± 0.3 mm, and 1.2 ± 0.6 mm) compared to IP (2.8 ± 1.6°, 0.7 ± 0.3 mm, and 1.2 ± 0.5 mm, p ≤ 0.004). Implants placed in TRS demonstrated higher mean angular, crestal, and apical deviations (4.0 ± 1.7°, 0.8 ± 0.3 mm, and 1.6 ± 0.5 mm) compared to implants placed in SRS (2.5 ± 1.2°, 0.7 ± 0.3 mm, and 1.1 ± 0.4 mm) or HR (2.0 ± 0.9°, 0.5 ± 0.3 mm, and 0.8 ± 0.4 mm, p < 0.001).

CONCLUSIONS

Positional deviations during sCAIS procedures are initiated with the first implant osteotomy and persist throughout the drilling sequence. However, deviations slightly decreased after implant placement. The alveolar ridge morphology is strongly associated with positional deviations. Higher deviations were observed in three-rooted and single-rooted sockets simulating an immediate approach compared to healed sites simulating a delayed protocol.

Surface roughness, optical properties, and microhardness of additively and subtractively manufactured CAD-CAM materials after brushing and coffee thermal cycling

PURPOSE

To evaluate the surface roughness, optical properties, and microhardness of additively or subtractively manufactured CAD-CAM materials after simulated brushing and coffee thermal cycling.

MATERIAL AND METHODS

Two additively manufactured resins (Crowntec, CT and VarseoSmile Crown Plus, VS) and 3 subtractively manufactured materials (a reinforced composite (Brilliant Crios, BC), a polymer-infiltrated ceramic network (Enamic, VE), and a feldspathic ceramic (Mark II, VM)) were used to fabricate disk-shaped specimens (Ø10×1-mm) (n = 10). Surface roughness, Vickers microhardness, and color coordinates were measured after polishing, while surface roughness was also measured before polishing. Specimens were then subjected to 25000 cycles of brushing and 10000 cycles of coffee thermal cycling, and measurements were repeated after each time interval. Color difference (ΔE00 ) and relative translucency parameter (RTP) were calculated. Robust analysis of variance test was used to evaluate surface roughness, ΔE00 , and RTP data, while generalized linear model analysis was used for microhardness data (α = 0.05).

RESULTS

Material type and time interval interaction affected tested parameters (p ≤ 0.002). In addition, material type affected all parameters (p < 0.001) other than surface roughness (p = 0.051), and time interval affected surface roughness and microhardness values (p < 0.001). Tested materials mostly had their highest surface roughness before polishing (p ≤ 0.026); however, there was no clear trend regarding the roughness of materials within different time intervals along with ΔE00 and RTP values within materials or time intervals. VS and CT had the lowest microhardness regardless of the time interval, while the remaining materials were listed as VM, VE, and BC in decreasing order (p < 0.001). Coffee thermal cycling only reduced the microhardness of VM (p < 0.001).

CONCLUSIONS

Tested additively manufactured resins can be considered more susceptible to simulated brushing and coffee thermal cycling than the other materials, given the fact that their surface roughness and ΔE00 values were higher than previously reported acceptability thresholds and because they had the lowest microhardness after all procedures were complete.

Effect of industrial scanner and framework material interaction on the marginal gaps of CAD-CAM complete arch implant frameworks

STATEMENT OF PROBLEM

Structured-light and computed tomography industrial scanners have been used as reference scanners to measure marginal gaps between implants and superstructures. However, the effect of framework material on the scanners' ability to detect gaps and on precision has not yet been evaluated.

PURPOSE

The purpose of this in vitro study was to investigate the interaction between the industrial scanner and framework material on measured marginal gaps of implant-supported fixed complete arch frameworks made from titanium and polymethylmethacrylate and on the precision of scans.

MATERIAL AND METHODS

A completely edentulous maxillary model with 4 implants and multiunit abutments at the first molar and canine sites was digitized by using a laboratory scanner. Implant-supported frameworks were milled from titanium and polymethylmethacrylate (n=5). Each framework was secured on the left molar site abutment. The marginal gaps between the frameworks and abutment sites without a screw were measured by using an industrial structured-light scanner and an industrial computed tomography scanner. The effect of the scanner, the framework material, and their interaction on measured gaps was analyzed by applying linear regressions and weighted least square methods. The F-statistics was used with Bonferroni corrections for precision analysis (α=.05).

RESULTS

No significant effect of scanner, material, or their interaction was found on the marginal gaps at the canine sites. The titanium framework gaps detected by using the computed tomography scanner were greater than those detected by using the structured-light scanner at the right molar site (estimated difference in means=0.054 mm; P=.003) and overall (estimated difference in means=0.023 mm; P=.033). The structured-light scanner's precision was higher than that of the computed tomography scanner when titanium frameworks were scanned (P=.001). The computed tomography scanner's precision was higher when scanning polymethylmethacrylate frameworks than when scanning titanium frameworks (P=.03).

CONCLUSIONS

Framework material and industrial scanner interaction affected the measured gaps. The computed tomography scanner detected greater marginal gaps with low precision when scanning titanium frameworks than the structured-light scanner. The sample size, the use of only 2 types of materials, and a laboratory scanner to obtain the computer-aided design file should be considered when interpreting the results.

Effect of internal connection type and screw channel angle on the screw stability of anterior implant-supported zirconia crowns

OBJECTIVES

To investigate the effect of implant-abutment connection and screw channel angle on screw stability by comparing a newly introduced and an established connection, before and after cyclic loading.

MATERIALS AND METHODS

Implants (N = 44) with Torcfit (TF) or Crossfit (CF) connection were divided to be restored with a straight (CFS and TFS) or an angled screw access channel (CFA and TFA) titanium-base abutment (n = 11). CFA and TFA received screw-retained crowns, whereas CFS and TFS received hybrid zirconia abutments and cement-retained crowns. The initial torque value (ITV) of each complex (ITVI ) and removal torque value (RTV) after 24 h (RTVI ) were measured. Screws were replaced with new ones, ITVs were recorded again (ITVF ), and crowns were cyclically loaded (2.4 million cycles, 98 N) to measure RTVs again (RTVF ). Percentage torque loss was calculated. Data were analyzed (α = 0.05).

RESULTS

ITVs were similar among groups (p ≥ .089). CF led to higher RTVs (p ≤ .002), while CFS had higher RTVI than CFA (p = .023). After 24 h, CFS had lower percentage torque loss than TF, while CFA had lower percentage torque loss than TFA (p ≤ .011). After cyclic loading, CF led to lower percentage torque (p < .001).

CONCLUSION

The implant-abutment connection affected the removal torque values. However, no screw loosening occurred during cyclic loading, which indicated a stable connection for all groups. Screw access channel angle did not affect screw stability after cyclic loading.

Effect of triangular mesh resolution on the geometrical trueness of segmented CBCT maxillofacial data into STL format

OBJECTIVES

To determine the optimal level of mesh reduction that would maintain acceptable levels of geometrical trueness while also minimizing the impact on other parameters such as file size and processing time.

METHODS

Intraoral and extraoral maxillofacial defects were created on 8 cadaver heads and scanned by using a CBCT scanner (NewTom 3D Imaging, Verona). DICOM data were segmented to produce head (n=8) and skull models (n=8) saved as standard tessellation language (STL) files. A further processing of head models was preformed to produce face (n=8) and ear models (n=8). A mesh reduction process was performed for each STL model (reference, R0) by generating 50% (R1), 75% (R2), and 90% (R3) reductions. The 3 datasets were compared to the R0 file using 3D evaluation software (GOM Inspect) using a global best-fit algorithm, to calculate the root mean square (RMS) deviations. Statistical analyses were performed at a level of significance of α=0.05.

RESULTS

There was no 3D deviation after the 50% triangular mesh reduction in the 4 datasets. Minor 3D deviations were observed after 75% reduction, in all groups. After 90% reduction, higher 3D deviations were observed, and especially in head and skull. Statistically significant increase in 3D deviations was observed with higher degrees of mesh reduction (p < 0.001).

CONCLUSION

The resolution of CBCT-based maxillofacial defect models can be reduced up to 50%, with neglectable concern to inaccuracy.

CLINICAL SIGNIFICANCE

Accurate maxillofacial models can be obtained from CBCT DICOM files after segmentation and export as STL files, even when the mesh resolution is reduced up to 50%. This information can be valuable for practitioners and researchers working with 3D models of maxillofacial defects.

Management of compromised spacing in the esthetic zone by combining an ultra-thin partial ceramic veneer and a ceramic implant crown: a case report of a multi-disciplinary approach and technique description

Dental implants have been commonly used to replace missing single teeth. However, esthetic rehabilitation of an adjacent tooth may also be required due to diastemas, crowding, or existing large direct restorations to improve the final esthetic outcome. With the advancements in ceramics and bonding techniques, minimally invasive esthetic approaches have become viable for compromised spacing issues. This case report describes a dental technique for the esthetic rehabilitation of compromised anterior spacing with a customized zirconia implant abutment at maxillary central incisor site and a partial ceramic veneer bonded to adjacent central incisor.

Which clinical and laboratory procedures should be used to fabricate digital complete dentures? A systematic review

STATEMENT OF PROBLEM

Digital workflows for digital complete denture fabrication have a variety of clinical and laboratory procedures, but their outcomes and associated complications are currently unknown.

PURPOSE

The purpose of this systematic review was to evaluate the clinical and laboratory procedures for digital complete dentures, their outcomes, and associated complications.

MATERIAL AND METHODS

Electronic literature searches were conducted on PubMed/Medline, Embase, and Web of Science for studies published from January 2000 to September 2022 and screened by 2 independent reviewers. Information on digital complete denture procedures, materials, their outcomes, and associated complications was extracted.

RESULTS

Of 266 screened studies, 39 studies were included. While 26 assessed definitive complete dentures, 7 studies assessed denture bases, 2 assessed trial dentures, and 4 assessed the digital images only. Twenty-four studies used border molded impression technique, 3 studies used a facebow record, and 7 studies used gothic arch tracing. Only 13 studies performed trial denture placement. Twenty-one studies used milling, and 17 studies used 3D printing for denture fabrication. One study reported that the retention of maxillary denture bases fabricated from a border-molded impression (14.5 to 16.1 N) was statistically higher than the retention of those fabricated from intraoral scanning (6.2 to 6.6 N). The maximum occlusal force of digital complete denture wearers was similar across different fabrication procedures. When compared with the conventional workflow, digital complete dentures required statistically shorter clinical time with 205 to 233 minutes saved. Up to 37.5% of participants reported loss of retention and up to 31.3% required a denture remake. In general, ≥1 extra visit and 1 to 4 unscheduled follow-up visits were needed. The outcomes for patient satisfaction and oral health-related quality of life were similar between conventional, milled, and 3D-printed complete dentures.

CONCLUSIONS

Making a border-molded impression is still preferred for better retention, and trial denture placement is still recommended to optimize the fabrication of definitive digital complete dentures.

Group 4 ITI Consensus Report: Patient benefits following implant treatment in partially and fully edentulous patients

OBJECTIVES

The aim of Working Group 4 was to address patient benefits associated with implant dentistry. Focused questions on (a) dental patient-reported outcomes (dPROs), (b) improvement in orofacial function, and (c) preservation of orofacial tissues in partially and fully edentulous patients following provision of implant-retained/supported dental prostheses were addressed.

MATERIALS AND METHODS

Three systematic reviews formed the basis for discussion. Participants developed statements and recommendations determined by group consensus based on the findings of the systematic reviews. These were then presented and accepted following further discussion and modifications as required by the plenary of the 7th ITI Consensus Conference, taking place in 2023 in Lisbon, Portugal.

RESULTS

Edentulous patients wearing complete dentures (CD) experience substantial improvements in overall dPROs and orofacial function following treatment with either complete implant-supported fixed dental prostheses (CIFDP) or implant overdentures (IODs). With respect to dPROs, mandibular IODs retained by two implants are superior to IODs retained by one implant. However, increasing the number of implants beyond two, does not further improve dPROs. In fully edentulous patients, rehabilitation with CIFDP or IOD is recommended to benefit the preservation of alveolar bone and masseter muscle thickness.

CONCLUSIONS

Completely edentulous patients benefit substantially when at least the mandible is restored using an CIFDP or an IOD compared to CD. In fully edentulous patients, implant prostheses are the best option for tooth replacement. The availability of this treatment modality should be actively promoted in all edentulous communities, including those with limited access and means.

Treatment effect of implant-supported fixed complete dentures and implant overdentures on patient-reported outcomes: A systematic review and meta-analysis

OBJECTIVES

To analyze the effect of implant treatment in edentulous patients rehabilitated with implant-supported fixed complete dentures (IFCDs) or implant overdentures (IODs) on dental patient-reported outcomes (dPROs).

MATERIALS AND METHODS

In January 2022, Medline, Embase, CINAHL, Cochrane Library, PubMed Central, Web of Science, and ClinicalTrials.gov were screened for prospective clinical studies on completely edentulous patients treated with IFCDs and/or IODs, reporting pre-treatment and follow-up dPROs. Hedges' g effect sizes (ES) with corresponding 95% confidence intervals (CI) were calculated. Afterward, meta-analyses were conducted using random effect models.

RESULTS

A total number of 1608 records was initially identified. Of those, 28 studies reporting dPROs from 1457 patients were finally included. The applied dental patient-reported outcome measures (dPROMs) included several versions of the Oral Health Impact Profile (OHIP) or specific items assessing satisfaction with Visual Analogue Scales (VAS). The overall ES was large for rehabilitation with IFCDs (1.68 [CI: 1.15, 2.20]) and IODs (1.26 [CI: 0.99, 1.52]) with no significant difference (p = .165) between the two. Denture stability was the only factor rated significantly higher for IFCDs (ES difference: 2.37 [CI: 0.21, 4.54]; p = .032). Subgroup analyses revealed moderately higher ES for IODs on two implants relative to one implant (ES difference: 0.73 [CI: 0.34, 1.12]; p < .001).

CONCLUSIONS

There is a strong positive effect of implant treatment in edentulous patients, independent of the type of prosthetic rehabilitation. In patients seeking high stability, IFCDs may be preferable. In mandibular IODs on a single implant, there was a significantly positive effect of an additional implant on dPROs.

Accuracy of implant placement in the posterior maxillary region depending on the alveolar residual bone height and sinus morphology: An in vitro study

OBJECTIVES

The primary aim of this in vitro study was to assess the effect of alveolar residual bone height in the posterior maxilla on the accuracy of the final implant position via free-handed and static Computer-Assisted Implant Placement (sCAIP). The secondary aim was to evaluate the influence of the maxillary sinus morphology on the accuracy of final implant position.

MATERIALS AND METHODS

Partially edentulous standardized maxillary models simulating three different residual bone heights and different sinus floor morphologies were investigated. One-hundred eighty equally distributed implants, which were placed either free-handed or sCAIP, constituted the study sample. 3D digital deviations were obtained by superimposing the post-surgical scans on the initial treatment plan.

RESULTS

Angular and linear deviation assessment demonstrated higher implant position accuracy in the sCAIP group. sCAIP revealed similar outcomes independently of the alveolar bone height and sinus floor morphology. Contrarily, in the free-handed group, alveolar bone height and sinus morphology statistically affected the final implant position. Non-parametric three-way ANOVA showed significance for implant placement protocol (p < .0001) and alveolar bone height (p ≤ .02) when angular, and linear deviations were evaluated. Sinus morphology was statistically significantly associated with angular deviation (p = .0009).

CONCLUSIONS

sCAIP demonstrated higher 3D implant position accuracy. Alveolar bone height (strongly) and sinus morphology are associated with the accuracy of final implant position when the free-handed implant protocol is followed. However, these anatomical factors did not affect final implant position during sCAIP.

Exploring preferences of older adults for dental services: A pilot multi-national discrete choice experiment

OBJECTIVES

To pilot an exploration of older adults' future preferences using discrete choice experiments to understand who should provide dental examinations and treatment, where these services should be provided, and participants' willingness to pay and willingness to travel.

BACKGROUND

The proportion of older adults in the general population is increasing and is recognised as a pressing public health challenge.

MATERIALS AND METHODS

Older people aged 65 years and over were recruited into this study from the UK, Switzerland and Greece. Drawing on earlier stakeholder engagement, a set of choice experiments are developed to explore the future preferences of older people for dental examinations and dental treatment, as they anticipated losing their independence. These were presented to the participants using a range of platforms, because of the COVID pandemic. Data were analysed in STATA using a random-effects logit model.

RESULTS

Two hundred and forty-six participants (median age 70 years) completed the pilot study. There was a strong preference across all countries for a dentist to undertake a dental examination (Greece: β = 0.944, Switzerland: β = 0.260, UK β = 0.791), rather than a medical doctor (Greece: β = -0.556, Switzerland: β = -0.4690, UK: β = -0.468). Participants in Switzerland and the UK preferred these examinations to be undertaken in a dental practice (Switzerland: β = 0.220, UK: β = 0.580) while participants in Greece preferred the dental examination to be undertaken in their homes (β = 1.172). Greek participants preferred dental treatment to be undertaken by a specialist (β = 0.365) in their home (β = 0.862), while participants from the UK and Switzerland preferred to avoid any dental treatment at home (Switzerland: β = -0.387; UK: β = -0.444). Willingness to pay analyses highlighted that participants in Switzerland and the UK were willing to pay more to ensure the continuity of future service provision at a family dental practice (Switzerland: β = 0.454, UK: β = 0.695).

CONCLUSION

Discrete choice experiments are valuable for exploring older people's preferences for dental service provision in different countries. Future larger studies should be conducted to further explore the potential of this approach, given the pressing need to design services that are fit for purpose for older people. Continuity of dental service provision is considered as important by most older people, as they anticipate losing their dependence.

Distortion assessment of different materials in full-arch dentate impressions in relation to operator experience: a comparative in vivo

PURPOSE

Evaluating the distortion probability in impressions of completely dentate arches when different impression materials are used in relation to operator experience.

MATERIAL AND METHODS

Twenty-eight students (group A) and 7 dentists (group B) performed 3 maxillary impressions on 28 students (participants), each using vinyl siloxane ether (VSE), polyether (PE), and irreversible hydrocolloid (IHC). Gypsum master casts were fabricated and subsequently digitized. Intraoral scans were taken as a control. Differences between master casts and intraoral scans were visualized by heatmaps and planar deviations were investigated. If planar deviations of >120 μm were found, the impression was rated as "distorted." An additional superimposition using the casts from VSE or PE was performed to confirm the presence of distortions. The relative number of surfaces with distortions in each impression was calculated. The procedure was repeated for a distortion threshold of 500 μm. The statistical analyses included measures ANOVA and post-hoc tests (a < 0.05).

RESULTS

When 120 μm was considered as the threshold for distortions, IHC impressions showed higher distortion probability than PE impressions in group A (P = 0.003) and group B (P < 0.0001). In group B only, PE showed a lower distortion probability than VSE (P = 0.02). There was no difference between the study groups (P = 0.42). Considering 500 μm as a threshold for distortions, there was no difference between impression materials (P = 0.17) or study groups (P = 0.53).

CONCLUSION

There were no statistic significant differences in relation to operator experience. Different impression materials had a significant impact on distortion probability. Polyether impressions showed the lowest distortion probability. Int J Prosthodont. 10.11607/ijp.8555.

Bond strength of additively manufactured composite resins to dentin and titanium when bonded with dual-polymerizing resin cements

STATEMENT OF PROBLEM

Additively manufactured composite resins for definitive restorations have been recently introduced. The bond strength between these composite resins and different substrates has not been extensively studied.

PURPOSE

The purpose of this in vitro study was to measure the shear bond strength (SBS) between additively manufactured composite resins and dentin and titanium substrates and compare those with the SBS between subtractively manufactured polymer-infiltrated ceramic and the same substrates (dentin and titanium), when different dual-polymerizing resin cements were used.

MATERIAL AND METHODS

One hundred and eighty cylinder-shaped specimens (Ø5×5 mm) were prepared from 3 materials recommended for definitive restorations: an additively manufactured composite resin (Crowntec [CT]); an additively manufactured hybrid composite resin (VarseoSmile Crown Plus [VS]); and a subtractively manufactured polymer-infiltrated ceramic (Enamic [EN]) (n=60). Specimens were randomly divided into six subgroups to be cemented to the two substrates (dentin and titanium; n=30) with 1 of 3 resin cements (RelyX Universal, Panavia V5, and Variolink Esthetic DC) (n=10). The restoration surface to be bonded was treated according to the respective manufacturer's recommendations. Dentin surfaces were treated according to the resin cement (Scotchbond Universal Plus Adhesive for RelyX Universal, Panavia V5 Tooth Primer for Panavia V5, and Adhese Universal for Variolink Esthetic DC), while titanium surfaces were airborne-particle abraded, and only the specimens paired with Panavia V5 were treated with a ceramic primer (Clearfil Ceramic Primer Plus). SBS was measured in a universal testing machine at a crosshead speed of 1 mm/min. Failure modes were analyzed under a microscope at ×12 magnification. Data were analyzed by using 2-way analysis of variance and Tukey honestly significant difference tests (α=.05).

RESULTS

When SBS to dentin was considered, only restorative material, as a main factor, had a significant effect (P<.001); EN had the highest SBS (P<.001), while the difference in SBS values of CT and VS was not significant (P=.145). As for SBS to titanium, the factors restorative material and resin cement and their interaction had a significant effect (P<.001). Within each resin cement, EN had the highest SBS to titanium (P<.001), and within each restorative material, Variolink resulted in the lowest SBS (P≤.010). Overall, EN and RelyX were associated with the highest SBS to titanium (P≤.013). Mixed failures were predominant in most groups.

CONCLUSIONS

Regardless of the substrate or the resin cement used, the subtractively manufactured polymer-infiltrated ceramic had higher shear bond strength than the additively manufactured composite resins. The SBS of the additively manufactured composite resins, whether bonded to dentin or titanium, were not significantly different from each other. Regardless of the restorative material, Variolink DC resulted in the lowest SBS for titanium surfaces.

Scan accuracy and time efficiency of different implant-supported fixed partial denture situations depending on the intraoral scanner and scanned area: An in vitro study

STATEMENT OF PROBLEM

The type of intraoral scanner (IOS), region of the implant, and extent of the scanned area have been reported to affect scan accuracy. However, knowledge of the accuracy of IOSs is scarce when digitizing different partially edentulous situations either with complete- or partial-arch scans.

PURPOSE

The purpose of this in vitro study was to investigate the scan accuracy and time efficiency of complete- and partial-arch scans of different partially edentulous situations with 2 implants and 2 different IOSs.

MATERIAL AND METHODS

Three maxillary models with implant spaces at the lateral incisor sites (anterior 4-unit), right first premolar and right first molar sites (posterior 3-unit), or right canine and right first molar sites (posterior 4-unit) were fabricated. After placing implants (Straumann S RN) and scan bodies (CARES Mono Scanbody), models were digitized by using an optical scanner (ATOS Capsule 200MV120) to generate reference standard tessellation language (STL) files. Complete- or partial-arch scans (test scans) of each model were then performed by using 2 IOSs (Primescan [PS] and TRIOS 3 [T3]) (n=14). The duration of the scans and the time needed to postprocess the STL file until the design could be started were also recorded. A metrology-grade analysis software program (GOM Inspect 2018) was used to superimpose test scan STLs over the reference STL to calculate 3D distance, interimplant distance, and angular (mesiodistal and buccopalatal) deviations. Nonparametric 2-way analysis of variance followed by Mann-Whitney tests with Holm correction were used for trueness, precision, and time efficiency analyses (α=.05).

RESULTS

The interaction between IOSs and scanned area only affected the precision of the scans when angular deviation data were considered (P≤.002). Trueness of the scans was affected by IOSs when 3D distance, interimplant distance, and mesiodistal angular deviations were considered. The scanned area affected only 3D distance deviations (P≤.006). IOSs and scanned area significantly affected the precision of scans when 3D distance, interimplant distance, and mesiodistal angular deviations were considered, while only IOSs significantly affected buccopalatal angular deviations (P≤.040). Scans from PS had higher accuracy when 3D distance deviations were considered for the anterior 4-unit and posterior 3-unit models (P≤.030), when interimplant distance deviations were considered for complete-arch scans of the posterior 3-unit model (P≤.048), and when mesiodistal angular deviations were considered in the posterior 3-unit model (P≤.050). Partial-arch scans had higher accuracy when 3D distance deviations of the posterior 3-unit model were considered (P≤.002). PS had higher time efficiency regardless of the model and scanned area (P≤.010), while partial-arch scans had higher time efficiency when scanning the posterior 3-unit and posterior 4-unit models with PS and the posterior 3-unit model with T3 (P≤.050).

CONCLUSIONS

Partial-arch scans with PS had similar or better accuracy and time efficiency than other tested scanned area-scanner pairs in tested partial edentulism situations.

Influence of alveolar ridge morphology and guide-hole design on the accuracy of static Computer-Assisted Implant Surgery with two implant macro-designs: An in vitro study

OBJECTIVES

The primary aim of this in vitro study was to evaluate the influence of alveolar ridge morphologies on the accuracy of static Computer-Assisted Implant Surgery (sCAIS). The secondary aims were to evaluate the influence of guide-hole design and implant macro-design on the accuracy of the final implant position.

METHODS

Eighteen standardized partially edentulous maxillary models with two different types of alveolar ridge morphologies were used. Each model was scanned via cone beam computer tomography prior to implant placement and scanned with a laboratory scanner prior to and following implant placement using sCAIS. The postsurgical scans were superimposed on the initial treatment planning position to measure the deviations between planned and postsurgical implant positions.

RESULTS

Seventy-two implants were equally distributed to the study groups. Implants placed in healed alveolar ridges showed significantly lower mean deviations at the crest (0.36 ± 0.17 mm), apex (0.69 ± 0.36 mm), and angular deviation (1.86 ± 0.99°), compared to implants placed in fresh extraction sites (0.80 ± 0.29 mm, 1.61 ± 0.59 mm, and 4.33 ± 1.87°; all p<0.0001). Implants placed with a sleeveless guide-hole design demonstrated significantly lower apical (1.02 ± 0.66 mm) and angular (2.72 ± 1.93°) deviations compared to those placed with manufacturer's sleeves (1.27 ± 0.67 mm; p = 0.01, and 3.46 ± 1.9°; p = 0.02). Deep-threaded tapered bone level implants exhibited significantly lower deviations at the crest (0.49 ± 0.28 mm), apex (0.97 ± 0.63 mm), and angular deviations (2.63 ± 1.85°) compared to shallow-threaded parallel-walled bone level implants (0.67 ± 0.34 mm; p = 0.0005, 1.32 ± 0.67 mm; p = 0.003, and 3.56 ± 1.93°; p = 0.01).

CONCLUSIONS

The accuracy of the final implant position with sCAIS is determined by the morphology of the alveolar ridge, the design of the guide holes, and the macrodesign of the implant.

CLINICAL SIGNIFICANCE

Higher accuracy in the final implant position was observed with implants placed in healed alveolar ridge morphologies, in implants with deep-threaded tapered macro-design, and when sleeveless surgical guide holes were used.

Effect of measurement techniques and operators on measured deviations in digital implant scans

OBJECTIVES

To evaluate the effect of different measurement techniques and operators on measured deviations in vitro implant scans.

METHODS

A 2-piece system that comprises a healing abutment (HA) and a scan body (SB) was mounted onto an implant at right first molar site of a polymethylmethacrylate mandibular dentate model. Model was digitized by using an industrial scanner (reference model scan, n = 1) and an intraoral scanner (test scan, n = 20). All standard tessellation language files were imported into a 3-dimensional analysis software and superimposed. Three operators with similar experience performed circle-based and point-based deviation analyses (n = 20). Deviations measured with different techniques were compared with paired samples t-test within each operator, while the reliability of the operators was assessed by using F-tests for both technqiues (α = 0.05).

RESULTS

Point-based technique resulted in lower deviations than circle-based technique for all operators (P = .001) with to higher reliability among operators (ICC = 0.438, P = .001). The correlation among the operators was nonsignificant when circle-based technique was used (ICC = 0.114, P = .189).

CONCLUSION

Lower deviations were detected with the point-based technique. In addition, different operators' measurements had higher correlation when point-based technique was used compared with circle-based technique.

CLINICAL SIGNIFICANCE

Point-based technique may be preferred over circle-based technique for research studies on scan accuracy of implants, given its higher reliability. The accuracy of measured deviations may increase if the number of planes are increased, which can facilitate point generation at different surfaces of the scan body.

Effect of intraoral scanner and fixed partial denture situation on the scan accuracy of multiple implants: An in vitro study

BACKGROUND

Accuracy of intraoral implant scans may be affected by the region of the implant and the type of the intraoral scanner (IOSs). However, there is limited knowledge on the scan accuracy of multiple implants placed for an implant-supported fixed partial denture (FPD) in different partially edentulous situations when digitized by using different IOSs.

PURPOSE

To investigate the effect of IOS and FPD situation on the scan accuracy of two implants when partial-arch scans were performed.

MATERIALS AND METHODS

Tissue level implants were placed in 3 maxillary models with implant spaces either at right first premolar and right first molar sites (Model 1, 3-unit FPD), at right canine and right first molar sites (Model 2, 4-unit FPD), or at lateral incisor sites (Model 3, 4-unit FPD). Reference standard tessellation language (STL) files of the models were generated by using an optical scanner (ATOS Capsule 200MV120). Two IOSs (CEREC Primescan [CP] and TRIOS 3 [TR]) were used to perform partial-arch scans (test-scans) of each model (n = 14), which were exported in STL format. A metrology-grade analysis software (GOM Inspect 2018) was used to superimpose test-scan STLs over the reference STL to calculate 3D distance, inter-implant distance, and angular (mesiodistal and buccopalatal) deviations. Trueness and precision analyses were performed by using bootstrap analysis of variance followed by Welch tests with Holm correction (α = 0.05).

RESULTS

Trueness of the scans was affected by IOS and FPD situation when 3D distance deviations were considered, while inter-implant distance, mesiodistal angular, and buccopalatal angular deviations were only affected by the FPD situation (p < 0.001). Scan precision was affected by the interaction between the IOSs and the FPD situation when 3D distance and buccopalatal angular deviations were concerned, while IOSs and FPD situation were effective when all deviations were concerned (p≤ 0.001). When 3D distance deviations were considered, CP scans had higher accuracy TR scans in Models 1 and 3 (p ≤ 0.002), and the Model 1 scans had the highest accuracy (p < 0.001). When inter-implant distance deviations were considered, Model 1 scans had the highest accuracy with CP and higher accuracy than Model 2 when TR was used (p ≤ 0.030). When mesiodistal angular deviations were considered, Model 1 scans had the highest accuracy (p ≤ 0.040). When buccopalatal angular deviations were considered, Model 1 scans had the highest accuracy among models when CP was used (p ≤ 0.020).

CONCLUSIONS

Posterior 3-unit fixed partial denture implant scans, CP scans, and combination of these two factors had accuracy either similar to or better than their tested counterparts.

Influence of drilling sequence and guide-hole design on the accuracy of static computer-assisted implant surgery in extraction sockets and healed sites-An in vitro investigation

OBJECTIVES

To evaluate the effect of drilling sequence, guide-hole design, and alveolar ridge morphology on the accuracy of implant placement via static computer-assisted implant surgery (sCAIS).

MATERIALS AND METHODS

Standardized maxillary bone models including single-tooth gaps with fresh extraction sockets or healed alveolar ridge morphologies were evaluated in this study. Implants were placed using different drilling sequences (i.e., complete [CDS] or minimum [MDS]), and guide-hole designs (i.e., manufacturer's sleeve [MS] or sleeveless [SL] guide-hole designs). The time for implant placement via sCAIS procedures was also recorded. The angular, crestal, and apical three-dimensional deviations between planned and final implant positions were digitally obtained. Statistical analyses were conducted by a non-parametric three-way ANOVA (α = .05).

RESULTS

Based on a sample size analysis, a total of 72 implants were included in this study. Significantly higher implant position accuracy was found at healed sites compared to extraction sockets and in SL compared to MS guide-hole design in angular, crestal, and apical 3D deviations (p ≤ .048). A tendency for higher accuracy was observed for the CDS compared to the MDS, although the effect was not statistically significant (p = .09). The MDS required significantly shorter preparation times compared with CDS (p < .0001).

CONCLUSION

Implant placement via sCAIS resulted in higher accuracy in healed sites than extraction sockets, when using SL compared to MS guides, and tended to be more accurate when using CDS compared to MDS. Therefore, even though surgery time was shorter with MDS, its use should be limited to strictly selected cases.

Double-Crown Prosthesis Retention Using Polyetherketoneketone (PEKK): An In Vitro Study

PURPOSE

To assess the retentive force of telescopic crowns using polyetherketoneketone (PEKK) high-performance polymer in relation to conventional materials over a long period of time in an in vitro setting.

MATERIALS AND METHODS

Thirty-six sets of primary and secondary crowns were fabricated as per the double crown-retained prostheses approach. Six samples were included in each of the five test groups (1: zirconia/PEKK [Zr/PEKK]; 2: titanium/PEKK [Ti/PEKK]; 3: cobalt-chrome/PEKK [CoCr/PEKK]; 4: PEKK/PEKK; and 5: gold/PEKK [Au/PEKK]) and the single control group (gold/galvano-gold [Au/GA]). The insertion-removal test was performed for 20,000 cycles, and the surface condition was observed. Retentive forces were analyzed using two-way ANOVA (α<0.05).

RESULTS

The retention forces in groups Zr/PEKK and Ti/PEKK significantly decreased over time (group 1: p = 0.035 and group 2: p = 0.001), whereas retentive force increased significantly in groups PEKK/PEKK, Au/PEKK, and control (group 4: p = 0.001, group 5: p = 0.008, and control: p = 0.042). Similar wear was observed on the primary crown in groups PEKK/PEKK, gold/PEKK, and control.

CONCLUSIONS

Groups PEKK/PEKK and Au/PEKK showed a transition of retentive force similar to the control group. Groups PEKK/PEKK and Au/PEKK had similar wear on the surface compared to control. Therefore, PEKK has a promising clinical potential.

O-Ring Attachments on One-Piece Mini Dental Implants: In Vitro Analysis of Retention Force Reproducibility Using Different Pristine Matrix-O-Ring Combinations

PURPOSE

To analyze the influence of pristine matrix and O-ring dimensions on retention force and reproducibility in single one-piece mini dental implants (MDIs) with ball patrices under in vitro conditions.

MATERIALS AND METHODS

Three different matrix and O-ring combinations (MH1-MH3) were evaluated (n = 50 per group) on 1.8-mm-diameter implants. The matrices were manually mounted on the implants and were subsequently removed in a vertical linear manner using a metal pin with two strain gauges, recording the maximum force during disconnection. After five disconnections, the O-rings were exchanged, and the mean retention force was calculated, resulting in 50 values for each matrix and O-ring combination. Mean retention forces, SDs, and 95% CI were calculated. Analysis of variance was used to test the global differences, and post hoc pairwise comparisons were subsequently applied. The level of significance was set to P < .05.

RESULTS

ANOVA (global P < .0001) and pairwise comparisons (all P < .0001) demonstrated statistically significant differences among the three different matrix and O-ring combinations, with mean values of 5.18 N (MH 1), 6.73 (MH 2), and 9.08 (MH 3). Within each combination, retention force variations of > 1 N could not be demonstrated; ie, by exchanging O-rings, a similar retention force can be reestablished.

CONCLUSION

Matrix and O-ring dimensions have a significant influence on retention forces in one-piece MDIs. Pristine O-rings demonstrated highly reproducible initial retention forces in all matrices.

Effect of Abutment Cooling on Reverse Torque Values of Abutment Screws: An In Vitro Study

Purpose: To evaluate the effect of cooling on the reverse torque values of different abutments in bone-level and tissue-level implants. The null hypothesis was that there would be no difference in reverse torque values of abutment screws when cooled and uncooled implant abutments were compared. Materials and Methods: Bone-level and tissue-level implants (Straumann, each n = 36) were placed in synthetic bone blocks and subdivided into three groups (each n = 12) based on the abutment type (titanium base, cementable abutment, abutment for screw-retained restorations). All abutment screws were tightened to 35 Ncm torque. In half of the implants, a dry ice rod was applied on the abutments close to the implant-abutment connection for 60 seconds before untightening the abutment screw. The remaining implant-abutment pairs were not cooled. The maximum reverse torque values were recorded using a digital torque meter. The tightening and untightening procedure was repeated three times for each implant including cooling for the test groups, resulting in 18 reverse torque values per group. Two-way analysis of variance (ANOVA) was used to analyze the effect of cooling and abutment type on the measurements. Post hoc t tests were used to make group comparisons (α = .05). The P values of post hoc tests were corrected for multiple testing using the Bonferroni-Holm method. Results: The null hypothesis was rejected. Cooling and abutment type significantly affected the reverse torque values in bone-level implants (P = .004) but not in tissue-level implants (P = .051). The reverse torque values of bone-level implants significantly decreased after cooling (20.31 ± 2.55 Ncm vs 17.61 ± 2.49 Ncm). Overall mean reverse torque values were significantly higher in bone-level implants compared to tissue-level implants (18.96 ± 2.84 Ncm vs 16.13 ± 3.17 Ncm; P < .001). Conclusion: Cooling of the implant abutment led to a significant decrease in reverse torque values in bone-level implants and may therefore be recommended as a pretreatment before the application of procedures to remove a stuck implant part.

Influence of Cyclic Loading on Load to Failure of Different Ceramic CAD/CAM Implant-Supported Single Crowns

PURPOSE

To compare the load to failure values of different ceramic CAD/CAM implant crown materials with drilled screw access holes with and without cyclic loading applied.

MATERIALS AND METHODS

Forty zirconia abutments with a titanium base were pre-loaded onto implants to support maxillary right first premolar crowns that were milled from four different CAD/CAM ceramic materials (zirconia reinforced lithium silicate, hybrid ceramic, lithium disilicate, and zirconia; n = 10 each). After cementing the crowns, screw access channels were prepared by drilling through occlusal surfaces. Half of the specimens were subjected to cyclic loading for 5 million cycles at 2 Hz (n = 5/material). After cyclic loading, vertical loads were applied to failure, and the load to failure values of all crowns were recorded and statistically analyzed. Two-way analysis of variance was used with restricted maximum likelihood estimation and Tukey-Kramer adjustments (α = .05).

RESULTS

During cyclic loading, the zirconia abutment in one lithium disilicate specimen cracked at 2 million cycles, as well as a zirconia-reinforced lithium silicate crown. Results for the load to failure test series showed statistical differences between the materials. Zirconia resulted in significantly higher failure loads when compared to the other materials (P < .001). Cyclic loading did not significantly affect the load to failure values.

CONCLUSION

Cyclic loading did not significantly influence the load to failure of any of the materials tested. Zirconia crowns with drilled screw access channels cemented on zirconia abutments with a titanium base had higher load to failure values compared to the other ceramic crown materials.

Titanium-base abutments may have similar long-term peri-implant effects as non-bonded one-piece abutments

Design A single-centre (private practice), prospective, longitudinal, split-mouth, single-blind, randomised controlled clinical trial reported peri-implant parameters of individualised abutments bonded to titanium (Ti) bases during a five-year follow-up. The study complied with the ethical principles of the Helsinki Declaration and the CONSORT (Consolidated Standards of Reporting Trials) guidelines. It was approved by the Medical Ethical Committee of the University of Freiburg (013/1630) and registered in the German Clinical Trials Register (DRKS00006163).Case selection The included subjects had to be over 17 years of age, have an American Society of Anaesthesiologists score of 1, be a non-smoker, have a full-mouth plaque index (PI) below 20%, full-mouth bleeding index (BI) 20%, and planned with at least two dental implants but not adjacent to each other. Participants were excluded if they required simultaneous augmentation, were pregnant or breastfeeding, or had a history of periodontitis. Marginal bone loss (MBL) was the main clinical outcome, while local bleeding on probing (BoP), probing pocket depth (PPD), plaque Index (PI), local recession (REC), and relative attachment level (RAL) were also evaluated. The study timeline consisted of a screening (visit 1) and implant surgery (visit 2). Stage two was three months after implant surgery (visit 3), impression was two weeks after stage two (visit 4), followed up by baseline with a standardised radiograph (visit 5), one-year follow-up with radiographic and clinical parameters (visit 6), two-year follow-up (visit 7), three-year follow-up (visit 8), four-year follow-up (visit 9) and five-year follow-up (visit 10). In total, 24 subjects received two bone-level implants (Conelog, Camlog Biotechnologies, Basel, Switzerland) in the same arch and region up to 1 mm subcrestally. Their implant-abutment connection was an internal 7.5 degree conical connection platform-switch. Each subject received two abutments (one control and one test) as per the split-mouth design. The control abutments consisted of individualised, one-piece, computer-aided design/computer-aided manufacturing (CAD/CAM) titanium abutments, whereas the test abutments were CAD/CAM titanium abutments bonded to Ti-bases. The decision which implant was restored and in which way was made by a coin flip. The surgeon, patient and prosthodontist were blinded regarding the treatment allocation.Data analysis Descriptive measures and quantitative parameters were obtained from means, standard deviations, minimum and maximum values and 95% confidence intervals. The means of clinical parameters (six sites per implant) were MBL, BoP, PPD, PI, REC, and RAL. Paired t-tests were used for intragroup comparisons at different intervals as well as for intergroup comparisons within each time point. All data collected were considered until participants dropped out (that is, intention-to-treat principle). The significance level alpha was set to 0.05. The post-hoc power calculation of the MBL intergroup comparison dammed this trial as underpowered (power = 34%).Results All implants were osseointegrated after the healing stage and no implants were lost during the trial. Two subjects dropped out (one after the two-year follow-up and the other at the last appointment). Regarding MBL, no significant intergroup differences were found between the abutment groups. Nonetheless, significant intragroup differences were found at several visits (visit 6 to visit 10) compared to the baseline MBL (visit 5), indicating continuous bone level alterations. Concerning the BoP, no significant differences were identified. In terms of PPD, significant intergroup differences were found at visits 9 (p = 0.006) and 10 (p = 0.024), favouring Ti-base abutments. There were significantly intergroup differences in terms of REC (p = 0.014) at visit 10, with higher values in the one-piece abutment group. No differences were found in terms of PI.Conclusions A preliminary conclusion of this underpowered trial was that Ti-base abutments have a similar long-term effect to one-piece abutments on human peri-implant tissues.

Effect of thermal cycling on the flexural strength and hardness of new-generation denture base materials

PURPOSE

To evaluate the flexural strength and Vickers microhardness of different CAD-CAM denture base materials.

MATERIALS AND METHODS

Sixty rectangular specimens (64×10×3.3 ±0.2 mm) were fabricated from 3 different denture base materials (G-CAM, Graphene-reinforced polymethylmethacrylate, GC), Ivotion Base (Prepolymerized polymethylmethacrylate, IV), and Denturetec (3D-printed resin, DT) either by using additive (DT) or subtractive manufacturing (IV and GC). Specimens of each group were divided into 2 subgroups (thermal cycled or non-thermal cycled, n = 10/group). Non-thermal cycled specimens were stored in distilled water at 37°C for 24 hours and subjected to 3-point flexural strength test with a universal testing machine. Thermal cycled specimens were initially evaluated for Vickers microhardness and subjected to thermal cycling (10000 cycles at 5-55°C). Vickers microhardness values were re-measured, and the specimens were subjected to 3-point flexural strength test. Data were analyzed by using 2-way analysis of variance and Bonferroni-corrected Tukey honestly significant difference tests (α = .05).

RESULTS

Material type and condition significantly affected flexural strength (P≤.004), whereas their interaction was nonsignificant (P = .778). Overall flexural strength of the materials in decreasing order was GC, IV, and DT (P<.001), regardless of the condition. Material had a higher effect on flexural strength (ηp² = .731) than thermal cycling (ηp² = .142). The effect of the interaction between the material type and thermal cycling on Vickers microhardness was significant (P<.001). GC had the highest microhardness before and after thermal cycling (P<.001). IV had higher microhardness than DT before thermal cycling (P<.001). However, DT and IV showed similar microhardness after thermal cycling (P = .665). Thermal cycling decreased the microhardness of GC and IV (P≤.022), whereas its effect on DT's microhardness was nonsignificant (P = .538). Material type had the highest effect on microhardness (ηp² = .864) followed by the interaction between the main factors (ηp² = .258).

CONCLUSIONS

Graphene-reinforced polymethylmethacrylate had the highest flexural strength and Vickers microhardness values, regardless of thermal cycling. Thermal cycling reduced the flexural strength of all resins. Thermal cycling reduced the microhardness of milled polymethylmethacrylate, but not that of 3D-printed resin. This article is protected by copyright. All rights reserved.

Non-Precious Metal Alloy Double Crown-Retained Removable Partial Dentures: A Cross-Sectional In Vivo Investigation

(1) Background: An alternative material to precious metal alloys are non-precious metal alloys. The material properties of these are different and, therefore, their clinical, biological and mechanical behaviors may also differ. Hence, the purpose of this in vivo investigation was to analyze the clinical and patient-reported outcomes of patients restored with non-precious metal alloy double crown-retained removable partial dentures (NP-D-RPDs). (2) Methods: Partially edentulous patients were restored with non-precious metal alloy partially veneered NP-D-RPDs. Survival rates, success rates, failures and patient-reported outcomes were investigated and statistically evaluated. (3) Results: A total of 61 patients (65.6 ± 10.8 years) were included and clinically and radiographically examined. The mean follow-up time was 25.2 ± 16.5 months. In total, 82 NP-D-RPDs and 268 abutment teeth were examined. The overall survival rate of the NP-D-RPDs was 100% after a mean follow-up time of 2.1 years. The overall success rate was 68.3%. The overall satisfaction with the NP-D-RPDs was 94.3%. (4) Conclusions: Non-precious metal alloy partially veneered NP-D-RPDs seem to be an efficient alternative to precious metal alloy RPDs with excellent patient-reported outcomes.

Indirect repair of saliva-contaminated materials using veneering ceramics

PURPOSE

To analyze the in vitro efficacy of a surface conditioning liquid facilitating ceramic repairs of saliva-contaminated metal-ceramic and all-ceramic restorations.

MATERIALS AND METHODS

Specimens constructed from non-precious alloy (NPA), precious alloy (PA), lithium-disilicate (LD), zirconia (ZI), veneering ceramics for zirconia (VZI), veneering ceramics for lithium-disilicate (VLD), and veneering ceramics for metal alloys (VM) were manufactured (total: n = 168; each material n = 24). Veneering ceramic cylinders (thickness: 2mm) were hand-layered on top of the specimens. Shear bond strength (SBS) tests were performed, measuring the maximum bond strength (MBS) of the cylinders on the specimens. Following this, the specimens were artificially aged and stored in artificial saliva for 30 days at 37°C. After physical cleaning using aluminum oxide air abrasion, a new surface conditioning liquid was applied (test, n = 84) or not (control, n = 84). New ceramic cylinders were hand-layered followed by a second SBS test. Descriptive statistics, linear regression analyses, and a one-sample t-test (α = 0.05) were used to ascertain the differences within (pre- vs. post-repair) and between the groups.

RESULTS

All specimens in the test group could be repaired, whereas 18 repairs in the control group failed. After the repairs, an MBS decrease was observed for the NPA specimens of the control group (-15.5MPa, p = 0.004) but not among any of the test groups. Comparing the change in MBS between the test and control groups, the reduction was significantly higher in the repaired NPA specimens of the control group (mean difference 11.8 MPa, p = 0.017).

CONCLUSIONS

Using the analyzed surface conditioning liquid, metal-ceramic and all-ceramic materials can be repaired, while some repairs failed without the liquid. The initial bond strengths between core and veneering materials could be restored in all specimens when the new surface conditioning liquid was applied. This article is protected by copyright. All rights reserved.

Converting Bilateral Free-End Removable Partial Dentures to Implant-Assisted Removable Partial Dentures Using 6 mm Short Implants: Patient-Reported Outcomes of a Prospective Clinical Study

The study assessed oral health-related quality of life (OHRQoL) of patients who received two 6 mm short implants in mandibular molar sites, converting existing bilateral free-end removable partial dentures (RPDs) to implant-assisted RPDs (IARPDs). After a postsurgical healing period of 4 months, the participants received a non-retentive dome abutment for 8 weeks, and then a retentive ball abutment for another 8 weeks. Afterwards, the participants made their final choice on which abutment to keep. The final follow-up was 1 year after implant placement. OHRQoL was evaluated with the 49-items version of the Oral Health Impact Profile (OHIP-49) at the abutment exchanges and the final follow-up. Furthermore, numerical rating scales were used to analyze patient satisfaction after 1 year. Questionnaire data of 13 participants were evaluated. Overall, OHRQoL increased with both the dome (p = 0.02) and the ball abutments (p < 0.001), without a significant difference between the abutments (p = 0.953). The questionnaires revealed an improvement in terms of oral situation, quality of life, and masticatory capacity (all p < 0.01). Patients showed a significant preference for the ball abutments (p < 0.001). Converting RPDs to IARPDs resulted in significant improvement of OHRQoL. Patients seem to prefer retentive over non-retentive abutments, although no differences in terms of OHRQoL were observed.

Effect of Scanned Area and Operator on the Accuracy of Dentate Arch Scans with a Single Implant

Studies have shown the effect of the operator and scanned areas on the accuracy of single implant scans. However, the knowledge on the scan accuracy of the remaining dental arch during single implant scans, which may affect the occlusion, is limited. The aim of this study was to investigate the effect of scanned areas and the operator on the scan accuracy of a dentate arch while scanning a single implant. A dentate model with an anterior implant was digitized with a laboratory scanner (reference scan). Three operators with similar experience performed 10 complete- and 10 partial-arch scans (left 2nd molar to right canine) with an intraoral scanner (TRIOS 3), and these scans were superimposed over the reference. The accuracy was analyzed at 22 points in complete-arch and at 16 points in partial-arch scans on 2nd molars and incisors. Data were evaluated with 2-way ANOVA and Tukey HSD tests (α = 0.05). The trueness of the total scanned area was higher in partial- than in complete-arch scans (p < 0.001). The trueness and precision of the scans were higher in the anterior site compared with the posterior in complete- (trueness: p ≤ 0.022, precision: p ≤ 0.003) and partial-arch (trueness: p ≤ 0.016, precision: p ≤ 0.016) scans of each operator and when the operator scan data were pooled. The complete-arch scan’s precision was not influenced by the operator (p ≥ 0.029), whereas the partial-arch scans of operator 1 and 2 were significantly different (p = 0.036). Trueness was higher in partial- compared with complete-arch scans, but their precision was similar. Accuracy was higher in the anterior site regardless of the scan being a partial- or a complete-arch. The operator’s effect on the accuracy of partial- and complete-arch scans was small.

Assessing masticatory performance with a colour-mixing ability test using smartphone camera images

Background

Colour‐mixing ability tests are frequently used to assess masticatory performance, but the image acquisition process may be cumbersome and technique sensitive.

Objectives

To evaluate the reliability of smartphone camera images in assessing masticatory performance using a colour‐mixing ability test.

Methods

Participants were recruited into three groups of dental state (n = 20 each): fully dentate, removable partial denture wearers and complete denture wearers. After performing a colour‐mixing ability test, images of the gum specimens (Hue‐Check Gum©) were captured with two smartphones and compared with the images obtained from a flatbed scanner by two examiners. The images were analysed with a subjective‐ (SA) and an opto‐electronical assessment (VoH). Inter‐ and intra‐rater reliability were tested. ANOVA models with repeated measures were used for statistical analysis (⍺ = .05).

Results

All three image acquisition techniques were able to distinguish masticatory performance between different dental states. For SA, inter‐rater reliability was fair to substantial and intra‐rater reliability was substantial to almost perfect. For VoH, inter‐rater reliability with the smartphones was at times different between two examiners, but the intra‐rater assessment was reliable. The opto‐electronic analysis with smartphone images underestimated the masticatory performance significantly when compared to the flatbed scanner analysis. Seven‐day ageing of the specimens did not significantly affect the results.

Conclusions

The assessment of masticatory performance with the Hue‐Check Gum© is a reliable method. The use of smartphones may occasionally underestimate masticatory performance; image acquisition with a flatbed scanner remains the gold standard. A centralised analysis of the photographed wafer may foster the reliability of the diagnosis.

Effect of Potassium Aluminum Sulfate Application on the Viability of Fibroblasts on a CAD-CAM Feldspathic Ceramic before and after Thermocycling

Potassium aluminum sulfate (alum) is a known adjuvant, which has been used as a mordant in textile industry for color fixation. This material has potential to be incorporated into dentistry for color stability, yet its toxicity first needs to be evaluated. The present study aimed to evaluate the cytotoxic potential of potassium aluminum sulfate (alum) on fibroblasts when applied onto feldspathic ceramic before and after thermocycling. Forty-eight feldspathic ceramic specimens were divided into four groups (FC: no alum application or thermocycling; FCT: thermocycling without alum application; FA: alum application without thermocycling; FAT: alum application and thermocycling) (n = 12). Cell viability was assessed by using a tetrazolium salt 3-[4,5-dimethylthiazol-2-yl]-2,5-diphnyltetrazolium bromide assay at 24 and 72 h, and cell cultures without any ceramic specimens served as control (C). One sample from each material group was further analyzed with energy dispersive X-ray spectroscopy (EDX). Cell viability at different time intervals within each group was analyzed with Friedman tests, while Kruskal−Wallis tests were used to compare the test groups within each time interval. Pairwise comparisons were further resolved by using Wilcoxon tests (a = 0.05). C had lower (p = 0.01) and FA had higher (p = 0.019) cell viability after 72 h. After 24 h, the highest cell viability was observed in C (p ≤ 0.036). After 72 h, the differences between C and FA, C and FAT, FC and FA, and FCT and FAT were nonsignificant (p > 0.05). Cell viability was not affected by alum application or thermocycling at any time interval (p ≥ 0.631). EDX analysis showed an increase in potassium concentration in FA and FAT when compared with FC and FCT. Regardless of the time interval, alum application onto feldspathic ceramic and thermocycling did not influence the cell viability.

The influence of age and gender on perception of orofacial esthetics among laypersons in Switzerland

OBJECTIVE

The purpose of this study was to evaluate the perception and role of orofacial esthetics by laypersons, and how attitudes may be correlated with age and gender in Switzerland.

MATERIAL AND METHODS

Self-administrated questionnaires (SAQ) were distributed both conventionally and digitally to Swiss residents over 16 years of age (range 16-99 years). The participants were identified in the medical practice, at an open house of the ZMK Bern, in elderly care centers, and via the internet (Facebook and Instagram). To verify that the participants were Swiss residents and laypersons, they were checked by an operator (conventional) or were provided an exact description of eligible participants at the beginning of the SAQ (digital). The SAQ included 30 questions with multiple-choice responses and visual analogue scales (0-100) divided into four sections regarding dental appearance with respect to body esthetics, partner selection, employment and career opportunities, and overall health/quality-of-life. For statistical analysis, respondents were segregated into two age groups (<25 years and ≥25 years) and into two gender groups (male and female). Descriptive analyses, the Fisher exact test, and Welch's t-test were applied (α = 0.05).

RESULTS

Five hundred and two laypersons completed the SAQ. The study's hypothesis-that various age groups and genders have different perceptions of dental esthetics-was supported. The willingness to correct one's own dentition was lower among older participants (OR: 0.54; p = 0.001); charisma and dental esthetics were considered equally important with a trend toward charisma in both age groups (p = 0.003). The belief that excellent dentition improves employment chances at a job interview (OR: 0.47; p = 0.0003) was significantly lower among older participants, and the belief that dental correction would improve quality-of-life was significantly higher among older participants (OR: 1.81; p = 0.001). The assumption that individuals with attractive teeth appear happier was significantly lower among older respondents (OR: 0.67; p = 0.03). Women were less satisfied with their dental appearance and, proportionally, their willingness to receive correction was significantly higher (OR: 1.79; p = 0.01 and OR: 1.77; p = 0.002 relative to men, respectively). Moreover, male participants had a lower desire to have brighter teeth and undergo bleaching treatments (OR: 0.54; p = 0.002; OR: 0.53; p = 0.002). The proportion of men believing that having beautiful teeth improves attractiveness and employment chances was significantly lower (OR: 0.33; p = 0.02 and OR: 0.66; p = 0.04; respectively).

CONCLUSIONS

Within the limitations of this observational study, it was concluded that age and gender of laypersons in Switzerland have a significant impact on the perception of dental esthetics.

CLINICAL SIGNIFICANCE

Evaluating and quantifying perceptions of dental esthetics for daily life across various age groups and genders can improve clinicians' understanding of individual needs in order to offer patient-oriented dental care.

Soft Loading Protocol of Short Strategic Implants in Posterior Mandibles Supporting Removable Bilateral Free-End Prostheses: 1-Year Results of a Prospective Cohort Study

PURPOSE

To evaluate 1-year survival and success rates of 6-mm short implants placed in mandibular molar sites with two different abutments (dome/ball) retaining existing removable partial dentures (RPDs).

MATERIALS AND METHODS

In 19 patients, 38 implants of 6-mm length were placed bilaterally. After 4 months, each participant received the dome abutment, which 2 months later was exchanged with the ball abutment. Clinical data were recorded at abutment connection (4 months postsurgery) and at 6 and 12 months postsurgery, including probing depth, bleeding on probing, presence of plaque, and standardized radiographs. Implant success was assessed using the following criteria: presence of pain, mobility, radiographic bone loss, probing depth, and the presence of exudate. For descriptive analyses, mean and SD values were calculated. Paired sample t tests and linear regressions with a significance level of α .05 were applied to analyze <the evolution of peri-implant parameters and the influence of implant placement depth.

RESULTS

The overall mean marginal bone level alteration (DMBL) was 1.05 ± 0.69 mm. A statistically significant marginal bone loss over time was observed at the mesial and distal aspects of all implants (P < .05). The implant survival rate was 100%. No implants showed pain, exudate, mobility, or probing depth > 7 mm. Three implants were classified as having satisfactory survival due to a DMBL > 2 mm (resulting success rate: 92.1%). No influence of implant placement depth was found.

CONCLUSION

These short-term results suggest that short implants can be used in mandibular molar sites for additional posterior support of free-end RPDs. However, in individual cases, DMBL > 2 mm may occur.

Clinical performance of tooth implant-supported removable partial dentures: a systematic review and meta-analysis

OBJECTIVE

To assess the clinical performance of tooth implant-supported removable partial dentures in terms of abutment survival in relation to the attachment system used.

METHODS

An electronic search in MEDLINE/PubMed Web of Science and Cochrane Central Register of Controlled Trials databases was performed. The methodological quality of the studies was assessed using the Newcastle-Ottawa Scale. Survival rates after 3 years and 5 years, loss, and complication rates per 100 years were estimated by Poisson regression.

RESULTS

A total of twelve studies were included; eleven studies were used for the meta-analysis. Survival analysis for mixed attachments showed an estimated survival rate of 100% after 3 years and 5 years. For uniform attachments, the estimated survival rate was 99.3% after 3 years and 98.8% after 5 years. Tooth abutment survival analysis for mixed attachments estimated a survival rate of 95% after 3 years and 91.7% after 5 years: Uniform attachments reached a survival rate of 97.2% after 3 years and 95.4% after 5 years. The prosthetic survival rate was 100% for mixed and uniform abutments after 3 years and 5 years of function.

CONCLUSIONS

Tooth implant-supported removable partial dentures can be considered as a reliable option with excellent prosthetic and implant survival rates and favorable rates for the abutments after 3-year and 5-year follow-ups. Complications may be reduced when 5 or more abutments are used.

CLINICAL RELEVANCE

Tooth implant-supported removable partial dentures are a favorable and potential alternative to restore a partially edentulous arch by optimizing the number and distribution of abutments.

Influence of 3D analysis software on measured deviations of CAD-CAM resin crowns from virtual design file: an in-vitro study

OBJECTIVES

To evaluate a nonmetrology-grade and a metrology-grade 3D analysis software when measuring the deviations of CAD-CAM fabricated crowns from the virtual design file.

MATERIALS AND METHODS

A right first molar on a mandibular dentate model was prepared and scanned by using an intraoral scanner, i500 (Medit). A complete coverage crown was designed in standard tessellation language format and 20 resin crowns were fabricated by using computer aided design-computer aided manufacturing (CAD-CAM). The crowns were then digitized by using the same intraoral scanner (test-scans). Root mean square (RMS) method was used to evaluate the deviations between the test-scans and the design file of the crowns on 3 surfaces (overall, external, and internal) by using a metrology-grade, Geomagic Control X (3D Systems) and a nonmetrology-grade, Medit Link (Medit) software. The data were analyzed with Welch two-sample t-tests to compare two software for the non-inferiority of the nonmetrology-grade software with a 50 µm threshold and the potential superiority of the metrology-grade software (α = 0.05).

RESULTS

The Welch two-sample t-tests for the non-inferiority analysis showed that the differences between the nonmetrology-grade and the metrology-grade software were below the threshold of 50 µm for each surface tested (p <.001). The differences between the two-tested software were nonsignificant for each surface analyzed when superiority was considered (p ≥.194).

CONCLUSION

The nonmetrology-grade software performed similar to the metrology-grade software when analyzing the deviations of CAD-CAM crowns. Therefore, the nonmetrology-grade 3D analysis software may be considered for the deviation measurements of similar restorations.

CLINICAL SIGNIFICANCE

The trueness of crowns after fabrication may affect their fit, and 3D analysis of trueness prior to the delivery appointment with the tested nonmetrology-grade software after fabrication may facilitate potential clinical adjustments and delivery of the crowns.

Oral diadochokinesis and associated oro-facial function in young and old German mother-tongue speakers: A cross-sectional study

Objectives

The aims of this study were to compare oral diadochokinesis and to test associations with oro‐facial functional parameters in healthy young and old German speakers.

Background

Oral diadochokinesis is a key component in the concept of oro‐facial hypofunction and relates to tongue and lip motor function but may depend on the linguistic background.

Materials and methods

Healthy German speakers with a minimum of 20 teeth were recruited to form a young (<60 years) and an older group (≥60 years). Oral diadochokinesis was assessed as the number of repetitions/s for the monosyllables /pa/, /ta/ and /ka/ to evaluate movement capacity of the lip, the anterior region of the tongue and the posterior region of the tongue, respectively. Maximum voluntary lip force, maximum voluntary bite force, masticatory performance, maximum voluntary tongue pressure, xerostomia and swallowing function were assessed with validated instruments. Results are presented as median (IQR).

Results

Sixty participants formed the younger group (n = 35, 30.0 years [24.0‐49.0]) and the older group (n = 25, 64.0 years [62.0‐72.0]). Counts/s of /ta/ were different between age groups (younger group: 6.0 vs older group: 5.4) but not for syllables /pa/ (younger group: 6.0 vs older group: 5.8) and /ka/ (younger group: 5.6 vs older group: 5.0). The oral diadochokinesis with /pa/ was overall associated with maximum voluntary lip force; oral diadochokinesis performed with /ta/ was associated with tongue pressure, and oral diadochokinesis with /ka/ with swallowing function. Masticatory performance was not associated with oral diadochokinesis but with maximum voluntary bite force, xerostomia and with maximum voluntary tongue pressure.

Conclusions

The published thresholds for oral diadochokinesis should be reconsidered in non‐Japanese mother‐tongue speakers. However, they still play an important role in the overall concept of oro‐facial functional assessment.

Influence of the loading protocol and platform switching in two-implant bar-retained overdentures: 3-year results from a randomized controlled equivalence clinical trial

OBJECTIVES

To test the null hypothesis that vertical peri-implant bone level alterations (ΔIBL) are equivalent in immediately (IL) and 3-month post-placement (DL) loaded implants in mandibular implant overdentures (IODs) on two implants.

MATERIALS AND METHODS

Thirty-two patients receiving two interforaminal implants, one with a platform-switched and one with a platform-matching abutment were randomly assigned to the IL or DL group (allocation ratio 1:1). All implants were primarily splinted with chairside-customized bars, converting the existing removable complete dentures to IODs. Standardized radiographs were recorded. The influence of the loading protocol (IL vs. DL), implant platform (platform switched vs. platform matching), implant site (43 vs. 33), participant age (≤65 vs. >65 years), and definition of baseline (implant placement vs. implant loading) were analyzed, applying linear regression analyses (α = 0.05). The equivalence range was [-0.4; 0.4].

RESULTS

Three participants of the IL group were lost during follow-up. The overall mean ΔIBL was -0.96 ± 0.89 mm. The ΔIBL was equivalent in terms of the implant platform and implant site but not in terms of participant age (in favor of more elderly participants) and the loading protocol. A significantly smaller ΔIBL was observed in the IL when the baseline was considered to be implant placement (p = .017), but not when it was considered to be implant loading (p = .084).

CONCLUSION

Immediate loading of primary-splinted implants in two-implant bar-retained overdentures, seems beneficial relative to loading 3 months post-placement, with respect to ΔIBL. The ΔIBL were equivalent in terms of platform switching.