Reliability between the two-colour chewing gum and the gummy-jelly tests used for the assessment of masticatory performance

OBJECTIVE

This study aimed to evaluate the reliability of two methods used to assess masticatory performance and attempt to correlate them to achieve interchangeability between the methods.

METHODS

Twelve healthy dentate volunteers (men = 6, women = 6; mean age = 28.3 ± 4.1) with no known dental or medical pathologies were requested to participate in this study. Each participant completed three masticatory performance assessments, including two two-colour mixing-ability tests using chewing-gums (CG: gum#1 and gum#2) and the gummy-jelly (GJ) test. For each method, participants created five samples each (total = 15 measurements per participant, gum#1 = 5, gum#2 = 5, GJ = 5). For the gum#1 and gum#2 methods, the predetermined chewing cycles were fixed at 10, 15, 20, 25 and 30 cycles, and for the GJ method, the time duration was fixed at 10, 15, 20, 25 and 30 s. The parameter measures were submitted to Z-score transformation, and Bland-Altman plots were generated to graphically compare the differences between two techniques against their means. Additionally, mountain plot was used to assess the cumulative distribution of measurement error between the methods.

RESULTS

A total of 180 measurements were recorded. There were significant correlations between the number of chewing cycles/chewing time and masticatory performance using the gum#1 (r = -.753; p < .001), gum#2 (r = -.838; p < .001) and GJ (r = .730). When all tests were considered together for each method, significant correlations were found (p < .001). A descriptive range of mean values aiming to produce reference value ranges for predictive purposes was achieved considering the interchangeably among the methods [CG = GJ (VoH-mg = dL): 10 cycle = 10 s: 0.329 = 110; 15 cycles = 15 s: 0.177 = 164; 20 cycles = 20 s: 0.130 = 205; 25 cycles = 25 s: 0.086 = 200; 30 cycles = 30 s: 0.077 = 267].

CONCLUSION

The strong correlations and high consistency between the two masticatory performance methods found in this study conclude that the two assessment methods are reliable and interchangeable. Further evaluations are warranted to arrive at a conversion formula for translation of the results between the two methods.

One-Piece Mini Dental Implant-Retained Mandibular Overdentures: 10-Year Clinical and Radiological Outcomes of a Non-Comparative Longitudinal Observational Study

This study presents the first 10-year follow-up investigation of the implant survival and peri-implant outcomes of one-piece mini dental implants (MDIs) retaining mandibular implant overdentures (IODs), including marginal bone level alterations (ΔMBLs), clinical peri-implant parameters, and complications. Twenty participants with horizontally atrophied mandibles received complete dentures and four MDIs (diameter 1.8 mm) at baseline. The dentures were converted into IODs with O-ring attachments. The 10-year follow-up comprised a radiological assessment of ΔMBLs, peri-implant parameters, as well as biological and technical complications. Results from a 10-year follow-up of 14 participants showed a 100% implant survival rate for all 56 implants. The mean ΔMBL after 10 years was -1.12 ± 0.80 mm, with 49 implants classified as successful (ΔMBL < 2 mm) and 7 implants with satisfactory survival (ΔMBL 2-4 mm). Time after implant placement significantly influenced ΔMBL, with stable MBLs after 5 years. The prosthetic survival rate after 10 years was 93%. ΔMBLs were not influenced by implant position or gender but were significantly smaller in subjects older than 65 years. Conclusively, one-piece MDIs with O-ring attachments offer a reliable treatment option for horizontally atrophied mandibles after 10 years, with high implant and prosthetic survival rates, potentially benefiting from advanced age regarding peri-implant bone stability.

Clinical performance of polymer frameworks in dental prostheses: A systematic review

STATEMENT OF PROBLEM

High-performance polymers including polyetheretherketone (PEEK) and polyetherketoneketone (PEKK) have been used as substitutes for metal frameworks in dental prostheses. However, the clinical performance of polymer-based frameworks is still uncertain.

PURPOSE

The purpose of this systematic review was to compare the clinical performance of PEEK and PEKK with that of metal frameworks for different dental prostheses.

MATERIAL AND METHODS

This review follows the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) guidelines. Six databases and non-peer-reviewed literature (without language or follow-up restrictions) were searched for studies conducted before February 2022. Only clinical studies, either randomized clinical trials (RCTs) or nonrandomized clinical trials (N-RCTs), comparing the clinical performance of polymer and metal frameworks were included. The risk of bias and certainty of the evidence were assessed with the RoB 2.0, ROBINS-I, and GRADE. Biologic (plaque and gingival indices, probing depth, bleeding scores, implant stability quotient, marginal bone loss) and mechanical outcomes (ridge base relation, prosthetic marginal gap, and fracture) were assessed.

RESULTS

Only 9 studies (7 RCTs and 2 N-RCTs) were included, all with moderate to serious risk of bias and low to very low certainty of evidence. No meta-analysis was possible, but qualitative analysis revealed lower plaque and gingival indices, probing depth, and marginal bone loss, with higher survival rates for implant-supported fixed prostheses and overdentures fabricated with PEEK than for metal frameworks. No significant differences were found between groups for removable partial dentures. The marginal fit of PEEK frameworks was also better for single crowns. Three fractures were reported in the 3 PEKK fixed dental prostheses with cantilevers.

CONCLUSIONS

PEEK and PEKK seem to be promising materials for dental prostheses, with acceptable response from the periodontal tissue. However, further well-designed studies are necessary to better understand their clinical and long-term limitations.

Effect of printing layer thickness on the trueness of 3-unit interim fixed partial dentures

STATEMENT OF PROBLEM

Three-dimensional printing has facilitated the fabrication processes in dentistry. However, knowledge on the effect of layer thickness on the trueness of 3D printed fixed partial dentures (FPDs) is lacking.

PURPOSE

The purpose of this in vitro study was to compare the effect of printing layer thickness on the trueness of 3-unit interim FPDs fabricated by using additive manufacturing with that of those fabricated by subtractive manufacturing.

MATERIAL AND METHODS

The right first premolar and first molar teeth of a dentate mandibular model were prepared for a 3-unit restoration and then digitized by using an intraoral scanner. A 3-unit interim FPD was designed to fabricate 40 restorations by using either the additive (NextDent C&B MFH) with layer thicknesses of 20 μm (n=10), 50 μm (n=10), and 100 μm (n=10) or subtractive manufacturing technique (Upcera) (milled, n=10). After fabrication, the interim FPDs were digitized by using the same intraoral scanner and were superimposed over the design data by using a 3D analysis software program. Root mean square (RMS) was used to analyze the trueness of the restorations at 4 different surfaces (external, intaglio, marginal area, and intaglio occlusal) and as a complete unit (overall). Data were analyzed with the Kruskal-Wallis and Wilcoxon tests with Bonferroni correction (α=.05).

RESULTS

The 100-μm-layer thickness interim FPDs showed the greatest overall (P≤.015), external (P≤.021), and intaglio occlusal (P≤.021) deviations, whereas the milled interim FPDs showed the lowest (P=.001). No significant differences were found among the test groups for marginal RMS (P≥.108). The differences between the 50-μm-layer thickness and 100-μm-layer thickness interim FPDs for the intaglio surface deviations (P=.064) and between the 20-μm-layer thickness and 50-μm-layer thickness interim FPDs for each surface tested were not statistically significant (P≥.108).

CONCLUSIONS

The printing layer thickness had a significant effect on the trueness of the additively manufactured interim FPDs. However, subtractively manufactured interim FPDs presented higher trueness than those additively manufactured, regardless of the printing layer thickness.

Load bearing capacity of 3-unit screw-retained implant-supported fixed dental prostheses with a mesial and distal cantilever on a single implant: A comparative in vitro study

OBJECTIVES

To assess the mechanical durability of monolithic zirconia implant-supported fixed dental prostheses (iFDP) design on one implant, with a distal and a mesial extension cantilever bonded to a titanium base compared to established designs on two implants.

MATERIALS AND METHODS

Roxolid Tissue level (TL), and tissue level x (TLX) implants were used to manufacture screw-retained 3-unit iFDPs (n = 60, n = 10 per group), with following configurations (X: Cantilever; I: Implant, T: Test group, C: Control group): T1: X-I-X (TL); T2: X-I-X (TLX); T3: I-I-X (TL); T4: I-I-X (TLX); C1: I-X-I (TL); C2: I-X-I (TLX). The iFDPs were thermomechanically aged and subsequently loaded until fracture using a universal testing machine. The failure load at first crack (Finitial) and at catastrophic fracture (Fmax) were measured and statistical evaluation was performed using two-way ANOVA and Tukey's post-hoc tests.

RESULTS

The mean values ranged between 190 ± 73 and 510 ± 459 N for Finitial groups, and between 468 ± 76 and 1579 ± 249 N for Fmax, respectively. Regarding Finitial, neither the implant type, nor the iFDP configuration significantly influenced measured failure loads (all p > 0.05). The choice of implant type did not show any significant effect (p > 0.05), while reconstruction design significantly affected Fmax data (I-I-Xa < X-I-Xb < I-X-Ic) (p < 0.05). The mesial and distal extension groups (X-I-X) showed fractures only at the cantilever extension site, while the distal extension group (I-I-X) showed one abutment and one connector fracture at the implant/reconstruction interface.

CONCLUSION

Results suggest that iFDPs with I-X-I design can be recommended regardless of tested implant type followed by the mesial and distal extension design on one implant abutment (X-I-X).

Effect of coffee thermocycling on the surface roughness and stainability of denture base materials with different chemical compositions manufactured with additive and subtractive technologies

OBJECTIVE

To evaluate the effect of coffee thermocycling (CTC) on the surface roughness (Ra ) and stainability of denture base materials with different chemical compositions fabricated by using additive and subtractive manufacturing.

MATERIALS AND METHODS

Disk-shaped specimens were additively (FREEPRINT denture, AM) or subtractively (G-CAM, GSM and M-PM, SM) fabricated from three pink denture base materials in different chemical compositions (n = 10). Ra was measured before and after polishing, while color coordinates were measured after polishing. Specimens were subjected to CTC (5000 cycles) and measurements were repeated. Color differences (ΔE00 ) after CTC were calculated. Ra among different time intervals within materials was evaluated by using repeated measures analysis of variance (ANOVA), while 1-way ANOVA was used to evaluate the Ra of different materials within each time interval and the ΔE00 values. Color coordinates within each material were compared by using paired samples t-tests (α = 0.05).

RESULTS

Ra before polishing was the highest for all materials (p < 0.001), while SM had its lowest Ra after CTC and AM had its lowest Ra after polishing (p ≤ 0.008). Before polishing, AM had the highest Ra among the materials (p < 0.001). After polishing, SM had higher Ra than AM (p < 0.001). After CTC, GSM had the lowest Ra (p ≤ 0.048). SM had the lowest (p ≤ 0.031) and AM had the highest (p < 0.001) ΔE00 . CTC decreased the a* and b* values of SM and AM (p ≤ 0.017), and increased the L* values of AM (p < 0.001).

CONCLUSIONS

Polishing significantly reduced the surface roughness of all materials. CTC did not increase the surface roughness of materials above the clinically acceptable threshold. Only AM had perceptible color change when previously reported threshold values for denture base materials were considered.

CLINICAL SIGNIFICANCE

Tested denture base materials may have similar surface stability after coffee thermocycling. However, subtractively manufactured denture base materials may have improved color stability when subjected to long-term coffee consumption.

Effect of adhesive system, resin cement, heat-pressing technique, and thermomechanical aging on the adhesion between titanium base and a high-performance polymer

STATEMENT OF PROBLEM

Even though polyetheretherketone (PEEK) has become popular for various prosthetic indications, a standard adhesive protocol to bond the PEEK to titanium bases has not been yet established. How the heat-pressing technique performs in this respect is also not clear.

PURPOSE

The purpose of this in vitro study was to investigate the effect of an adhesive system-cement combination, the heat-pressing technique, and thermomechanical aging on the retention force between titanium bases and PEEK specimens.

MATERIAL AND METHODS

Sixty 9×11×20-mm PEEK specimens with a titanium base slot integrated into the design were milled to simulate an implant-supported PEEK framework for a cantilevered fixed prosthesis. The specimens were assigned to 8 groups (n=10) according to the titanium base primer (MKZ or Monobond) and resin cement (DTK or Multilink hybrid) used and with or without thermomechanical aging. Twenty PEEK specimens were directly heat-pressed on titanium bases, and half of the specimens were not subjected to thermomechanical aging (n=10). For nonaged groups, the PEEK specimen complex was tightened to an implant analog and secured on a custom-made pull-off device. Retention forces were measured by using the pull-off tensile test in a universal testing machine, and the maximum tensile bond strength (MPa) was calculated. The aged groups were subjected to 5000 cycles of thermal aging (5 °C to 55 °C), and the specimens were clamped to load the extension (cantilever) for 1 200 000 cycles with 120 N and 200 N at 1.5-Hz frequency. After aging, the pull-off test was performed for those specimens that survived thermomechanical aging. A nonparametric Kruskal-Wallis test was used to determine whether there was a difference among the groups, followed by pairwise Wilcoxon rank tests with Bonferroni correction. The Wilcoxon rank test was used to analyze the effect of thermomechanical aging in each adhesive system-cement or heat-press group (α=.05 for all tests).

RESULTS

None of the specimens failed during cyclic loading. According to the Kruskal-Wallis test, the effect of the PEEK-Ti base bonding technique on the retention force in the nonaged (P=.019) and thermomechanically aged groups was significant (P=.010). In the nonaged groups, the heat-pressing technique resulted in a higher retention force than when the specimens were bonded by using the Monobond-Multilink hybrid combination (P=.031). Thermomechanical aging did not significantly affect the results (P>.241). All failures were adhesive, with cement remaining only on the Ti-bases.

CONCLUSIONS

All bonding protocols tested resulted in a stable bond between PEEK and Ti-bases, as all specimens survived thermomechanical aging. The heat-pressing technique resulted in mean bond strength values similar to those obtained with the tested adhesive system-cement combinations with 1 exception; the nonaged heat-pressed groups presented higher bond strength than the Monobond-Multilink hybrid combination. Failure types indicated that the weaker bond was between the PEEK and the cements tested rather than between the titanium base and the cements, regardless of the adhesive system-cement combination.

An integration protocol for aligning intraoral scans to facial scans using the nasal geometry reference in a fully dentate patient

Advanced digital technologies have rapidly been integrated into prosthodontics to improve the digital workflow for prosthetic rehabilitation. The integration of 3D datasets acquired from various imaging sources such as intraoral scanners and facial optical scanners allows the creation of virtual patients to perform presurgical simulation and prosthetic rehabilitation. The presented technique introduced a straightforward protocol for aligning intraoral scans (Trios 4, 3Shape) to optical face scans (Face Hunter, Zirkonzahn) using a global best-fit algorithm of 3D evaluation software (GOM Inspect). Nasal geometry data were used as the matching reference to produce virtual dental patients. This integration protocol ensured that the intraoral scanner (Trios 4, 3Shape) was used not only to scan dental arches but also used effectively to scan the nose. These scans along with professional facial scans can be successfully aligned to produce virtual dental patients. As only a single fully dentate patient case with an alignment deviation of 243.6 µm was used, further research to evaluate the accuracy of this protocol is needed.

Dimensional Stability of Additively Manufactured Diagnostic Maxillary Casts Fabricated with Different Model Resins

PURPOSE

To evaluate the effect of model resin type and time interval on the dimensional stability of additively manufactured diagnostic casts.

MATERIALS AND METHODS

Ten irreversible hydrocolloid impressions and 10 impressions from an intraoral scanner were made from a reference maxillary stone cast, which was also digitized with a laboratory scanner. Conventional impressions were poured in type III stone (SC), while digital impressions were used to additively manufacture casts with a nanographene-reinforced model resin (GP) or a model resin (DM). All casts were digitized with the same laboratory scanner 1 day (T0), 1 week (T1), 2 weeks (T2), 3 weeks (T3), and 4 weeks (T4) after fabrication. Cast scans were superimposed over the reference cast scan to evaluate dimensional stability. Data were analyzed with Bonferroni-corrected repeated measures ANOVA (α = .05).

RESULTS

The interaction between the main factors (material type and time interval) affected anterior teeth deviations, while the individual main factors affected anterior teeth and entire-cast deviations (P ≤ .008). Within anterior teeth, DM had the lowest deviations at T3, and GP mostly had lower values at T2 and lower deviations at T3 than at T0 (P ≤ .041). SC had the highest pooled anterior teeth deviations, and GP had the highest pooled entire cast deviations (P < .001). T3 had lower pooled anterior teeth deviations than at T0, T1, and T4, and higher pooled entire cast deviations than T1 were demonstrated (P ≤ .027).

CONCLUSIONS

The trueness of nanographene-reinforced casts was either similar to or higher than that of other casts. Dimensional changes were acceptable during the course of 1 month.

Fabrication Trueness, Intaglio Surface Adaptation, and Marginal Integrity of Resin-Based Onlay Restorations Fabricated by Additive and Subtractive Manufacturing

PURPOSE

To evaluate the fabrication trueness, intaglio surface adaptation, and marginal integrity of resin-based onlay restorations made via additive manufacturing (AM) or subtractive manufacturing (SM).

MATERIALS AND METHODS

An onlay restoration was designed (DentalCAD Galway 3.0) and saved as an STL file to generate a design STL file (DO-STL). Using this design, 45 onlays were fabricated either with AM (3D-printed resin for definitive [AM-D; Tera Harz TC-80DP] and interim [AM-I; Freeprint temp] restorations) or SM (composite resin, Tetric CAD) technologies. Onlays were scanned with an intraoral scanner (CEREC Primescan SW 5.2), and the scans were saved as test STL files (TO-STLs). For trueness evaluation, TO-STLs were superimposed over the DO-STL, and root mean square (RMS) values of overall and intaglio surfaces were measured (Geomagic Control X). For the intaglio surface adaptation and marginal integrity, a triple-scan protocol was performed. Kolmogorov-Smirnov, one-way ANOVA, and post-hoc Tukey honestly significant difference tests were used to analyze data (α = .05).

RESULTS

RMS values of intaglio and overall surfaces, intaglio adaptation, and marginal integrity varied among test groups (P < .001). AM-D had the greatest overall surface RMS (P < .001), while SM had the greatest intaglio surface RMS (P < .001). SM had the highest average distance deviations for intaglio surface adaptation and marginal integrity, whereas AM-D had the lowest (P < .001).

CONCLUSIONS

AM-D onlays showed lower overall trueness than AM-I onlays and SM definitive onlays. However, AM-D onlays presented high intaglio surface trueness, intaglio surface adaptation, and marginal integrity.

Towards an operational definition of oral frailty: A e-Delphi study

OBJECTIVES

Building upon our recently developed conceptual definition of oral frailty (the age-related functional decline of orofacial structures), this e-Delphi study aims to develop an operational definition of oral frailty by identifying its components.

METHODS

We used a modified e-Delphi study to reach a consensus among international experts on the components of oral frailty. Twelve out of fifteen invited experts in the field of gerodontology participated. Experts responded to three rounds of an online 5-point scale questionnaire of components to be included or excluded from the operational definition of oral frailty. After each round, scores and rationales were shared with all experts, after which they could revise their position. A consensus was reached when at least 70% of the experts agreed on whether or not a component should be included in the operational definition of oral frailty.

RESULTS

The experts achieved a high level of agreement (80 - 100%) on including eight components of oral frailty and excluding nineteen. The operational definition of oral frailty should include the following components: 1) difficulty eating hard or tough foods, 2) inability to chew all types of foods, 3) decreased ability to swallow solid foods, 4) decreased ability to swallow liquids, 5) overall poor swallowing function, 6) impaired tongue movement, 7) speech or phonatory disorders, and 8) hyposalivation or xerostomia.

CONCLUSION

This e-Delphi study provided eight components that make up the operational definition of oral frailty. These components are the foundation for the next stage, which involves developing an oral frailty assessment tool.

Influence of intraoral scanner and finish line location on the fabrication trueness and margin quality of additively manufactured laminate veneers fabricated with a completely digital workflow

STATEMENT OF PROBLEM

Knowledge of the fabrication trueness and margin quality of additively manufactured (AM) laminate veneers (LVs) when different intraoral scanners (IOSs) and finish line locations are used is limited.

PURPOSE

The purpose of this in vitro study was to evaluate the fabrication trueness and margin quality of AM LVs with different finish line locations digitized by using different IOSs.

MATERIAL AND METHODS

An LV preparation with a subgingival (sub), equigingival (equi), or supragingival (supra) finish line was performed on 3 identical maxillary right central incisor typodont teeth. Each preparation was digitized by using 2 IOSs, (CEREC Primescan [PS] and TRIOS 3 [TS]), and a reference LV for each finish line-IOS pair (n=6) was designed. A total of 90 LVs were fabricated by using these files and urethane acrylate-based definitive resin (Tera Harz TC-80DP) (n=15). Each LV was then digitized by using PS to evaluate fabrication trueness (overall, external, intaglio, and marginal surfaces). Each LV was also qualitatively evaluated under a stereomicroscope (×60), and the cervical and incisal margin quality was graded. Fabrication trueness and cervical margin quality were evaluated by using 2-way analysis of variance, while Kruskal-Wallis and Mann Whitney-U tests were used to evaluate incisal margin quality (α=.05).

RESULTS

The interaction between the IOS type and the finish line location affected measured deviations at each surface (P≤.020). PS-sub and TS-supra had higher overall trueness than their counterparts. and the subgingival finish line resulted in the lowest trueness (P≤.005). PS and the subgingival finish line led to the lowest trueness of the external surface (P≤.001). TS-sub had the lowest intaglio surface trueness among the TS subgroups, and PS-sub had higher trueness than TS-sub (P<.001). PS-sub and PS-supra had higher marginal surface trueness than their TS counterparts (P<.001). TS resulted in higher cervical margin quality (P=.001).

CONCLUSIONS

Regardless of the IOS tested, subgingival finish lines resulted in the lowest trueness. The effect of IOS on the measured deviations varied according to the surface evaluated and finish line location. The cervical margin quality of AM LVs was higher when TS was used.

Tooth morphology, internal fit, occlusion and proximal contacts of dental crowns designed by deep learning-based dental software: A comparative study

OBJECTIVES

This study compared the tooth morphology, internal fit, occlusion, and proximal contacts of dental crowns automatically generated via two deep learning (DL)-based dental software systems with those manually designed by an experienced dental technician using conventional software.

METHODS

Thirty partial arch scans of prepared posterior teeth were used. The crowns were designed using two DL-based methods (AA and AD) and a technician-based method (NC). The crown design outcomes were three-dimensionally compared, focusing on tooth morphology, internal fit, occlusion, and proximal contacts, by calculating the geometric relationship. Statistical analysis utilized the independent t-test, Mann-Whitney test, one-way ANOVA, and Kruskal-Wallis test with post hoc pairwise comparisons (α = 0.05).

RESULTS

The AA and AD groups, with the NC group as a reference, exhibited no significant tooth morphology discrepancies across entire external or occlusal surfaces. The AD group exhibited higher root mean square and positive average values on the axial surface (P < .05). The AD and NC groups exhibited a better internal fit than the AA group (P < .001). The cusp angles were similar across all groups (P = .065). The NC group yielded more occlusal contact points than the AD group (P = .006). Occlusal and proximal contact intensities varied among the groups (both P < .001).

CONCLUSIONS

Crowns designed by using both DL-based software programs exhibited similar morphologies on the occlusal and axial surfaces; however, they differed in internal fit, occlusion, and proximal contacts. Their overall performance was clinically comparable to that of the technician-based method in terms of the internal fit and number of occlusal contact points.

CLINICAL SIGNIFICANCE

DL-based dental software for crown design can streamline the digital workflow in restorative dentistry, ensuring clinically-acceptable outcomes on tooth morphology, internal fit, occlusion, and proximal contacts. It can minimize the necessity of additional design optimization by dental technician.

Implementation of triple-scan protocol to evaluate the fit of complete-arch implant-supported fixed prostheses

Passive fit is essential for multiple-unit implant-supported prostheses. Conventional methods to assess the passivity of complete-arch implant-supported prostheses do not allow 3-dimensional (3D) visualization and quantification of misfit. This report describes the marginal and internal fit evaluation of a complete-arch implant-supported prosthesis by using the triple-scan protocol involving a scanner and a 3D analysis freeware. This technique allows researchers, clinicians, or dental technicians to detect and quantify 3D prosthetic misfit, which may facilitate the preparation for dental appointments and objective measurement of misfit for research studies.

Effect of coffee thermal cycling on the surface properties and stainability of additively manufactured denture base resins in different layer thicknesses

PURPOSE

To compare the effect of coffee thermal cycling on surface roughness (Ra), Vickers microhardness (MH), and stainability of denture base resins additively manufactured in different layer thicknesses with those of subtractively manufactured denture base materials.

MATERIALS AND METHODS

Eighty disk-shaped specimens (Ø10×2 mm) were fabricated from two subtractively (Merz M-PM [SM-M] and G-CAM [SM-G]) and three additively (NextDent 3D+ [50 µm, AM-N-50; 100 µm, AM-N-100], FREEPRINT Denture [50 µm, AM-F-50; 100 µm, AM-F-100], and Denturetec [50 µm, AM-S-50; 100 µm, AM-S-100]) manufactured denture base materials (n = 10). Ra measurements were performed before and after polishing by using a non-contact optical profilometer, while MH values and color coordinates were measured after polishing. Specimens were then subjected to 5000 cycles of coffee thermal cycling, all measurements were repeated, and color differences (ΔE00) were calculated. A linear mixed effect model was used to analyze Ra and MH data, while one-way analysis of variance was used to analyze ΔE00 data (α = 0.05). Ra values were further evaluated according to a clinically acceptable threshold of 0.2 µm, while ΔE00 values were evaluated according to perceptibility (1.72 units) and acceptability (4.08 units) thresholds. The interaction between the material type and the time interval affected both Ra and MH (p ≤ 0.001). Tested materials had their highest Ra before polishing (p ≤ 0.029). Before polishing, AM-F-100 had the highest, and SM-M and SM-G had the lowest Ra (p < 0.001). After polishing and after coffee thermal cycling, SM-G mostly had lower Ra than those of other materials (p ≤ 0.036). SM-G mostly had higher MH than that of other materials before and after coffee thermal cycling (p ≤ 0.025). Coffee thermal cycling reduced the MH of SM-M and increased that of AM-S-100 (p ≤ 0.024). AM-N-100 had higher ΔE00 than AM-F, AM-S-100, and SM-G (p ≤ 0.009), while AM-F and SM-G had lower ΔE00 than AM-S-50 and AM-N-50 (p ≤ 0.024).

CONCLUSIONS

Polishing reduced the surface roughness of all materials, whereas the effect of coffee thermal cycling was nonsignificant. Most of the tested materials had acceptable surface roughness after polishing and after coffee thermal cycling according to the reported threshold. Layer thickness only affected the microhardness of tested additively manufactured resins, which was material-dependent. Subtractively manufactured specimens mostly had high microhardness and that of nonreinforced subtractively manufactured resin decreased after coffee thermal cycling. When reported color thresholds are considered, all materials had acceptable color stability.

Effect of different disinfection protocols on the surface properties of CAD-CAM denture base materials

STATEMENT OF PROBLEM

Which disinfection protocol provides optimal water contact angle and microhardness for computer-aided design and computer-aided manufacturing (CAD-CAM) polymethyl methacrylate (PMMA) materials is unclear.

PURPOSE

The purpose of this in vitro study was to evaluate the effect of different disinfection protocols (1% sodium hypochlorite, denture cleanser gel, and effervescent tablet) on the water contact angle and microhardness of different CAD-CAM PMMA denture base materials by comparing them with a heat-polymerized PMMA.

MATERIAL AND METHODS

Disk-shaped specimens (Ø10×2 mm) were fabricated from 3 different CAD-CAM PMMAs-AvaDent (AV), Merz M-PM (M-PM), and Polident (Poli)-and a heat-polymerized PMMA (Vynacron) (CV) (n=21). Three disinfection protocols (1% sodium hypochlorite [HC], denture cleanser gel [GEL], an effervescent tablet [TAB]) were applied to simulate 180 days of cleansing. The water contact angle and microhardness of specimens were measured before and after disinfection and compared by using a 2-way ANOVA (α=.05).

RESULTS

For water contact angle, material (P=.010) and disinfection protocol (P=.002) had a significant effect. The material (P<.001), disinfection protocol (P=.001), and their interaction (P<.001) significantly affected the microhardness after disinfection. When the condition after disinfection was compared with that before disinfection, the water contact angle increased significantly in all material-disinfection protocol pairs (P≤.025), and microhardness increased significantly in all material-disinfection protocol pairs (P≤.040), except for GEL- (P=.689) or TAB-applied (P=.307) AV, HC-applied M-PM (P=.219), and TAB-applied Poli (P=.159).

CONCLUSIONS

The material and disinfection protocol affected the water contact angle of all tested PMMAs after disinfection, resulting in more hydrophobic surfaces for heat-polymerized or CAD-CAM PMMAs. The microhardness of heat-polymerized PMMA was less than that of all CAD-CAM PMMAs after disinfection, regardless of the protocol.

Effect of industrial scanner and framework material interaction on the marginal gaps of CAD-CAM complete arch implant frameworks

STATEMENT OF PROBLEM

Structured-light and computed tomography industrial scanners have been used as reference scanners to measure marginal gaps between implants and superstructures. However, the effect of framework material on the scanners' ability to detect gaps and on precision has not yet been evaluated.

PURPOSE

The purpose of this in vitro study was to investigate the interaction between the industrial scanner and framework material on measured marginal gaps of implant-supported fixed complete arch frameworks made from titanium and polymethylmethacrylate and on the precision of scans.

MATERIAL AND METHODS

A completely edentulous maxillary model with 4 implants and multiunit abutments at the first molar and canine sites was digitized by using a laboratory scanner. Implant-supported frameworks were milled from titanium and polymethylmethacrylate (n=5). Each framework was secured on the left molar site abutment. The marginal gaps between the frameworks and abutment sites without a screw were measured by using an industrial structured-light scanner and an industrial computed tomography scanner. The effect of the scanner, the framework material, and their interaction on measured gaps was analyzed by applying linear regressions and weighted least square methods. The F-statistics was used with Bonferroni corrections for precision analysis (α=.05).

RESULTS

No significant effect of scanner, material, or their interaction was found on the marginal gaps at the canine sites. The titanium framework gaps detected by using the computed tomography scanner were greater than those detected by using the structured-light scanner at the right molar site (estimated difference in means=0.054 mm; P=.003) and overall (estimated difference in means=0.023 mm; P=.033). The structured-light scanner's precision was higher than that of the computed tomography scanner when titanium frameworks were scanned (P=.001). The computed tomography scanner's precision was higher when scanning polymethylmethacrylate frameworks than when scanning titanium frameworks (P=.03).

CONCLUSIONS

Framework material and industrial scanner interaction affected the measured gaps. The computed tomography scanner detected greater marginal gaps with low precision when scanning titanium frameworks than the structured-light scanner. The sample size, the use of only 2 types of materials, and a laboratory scanner to obtain the computer-aided design file should be considered when interpreting the results.

Autoantibody status, neuroradiological and clinical findings in children with acute cerebellitis

BACKGROUND

Acute cerebellitis (AC) in children and adolescents is an inflammatory disease of the cerebellum due to viral or bacterial infections but also autoimmune-mediated processes.

OBJECTIVE

To investigate the frequency of autoantibodies in serum and CSF as well as the neuroradiological features in children with AC.

MATERIAL AND METHODS

Children presenting with symptoms suggestive of AC defined as acute/subacute onset of cerebellar symptoms and MRI evidence of cerebellar inflammation or additional CSF pleocytosis, positive oligoclonal bands (OCBs), and/or presence of autoantibodies in case of negative cerebellar MRI. Children fulfilling the above-mentioned criteria and a complete data set including clinical presentation, CSF studies, testing for neuronal/cerebellar and MOG antibodies as well as MRI scans performed at disease onset were eligible for this retrospective multicenter study.

RESULTS

36 patients fulfilled the inclusion criteria for AC (f:m = 14:22, median age 5.5 years). Ataxia was the most common cerebellar symptom present in 30/36 (83 %) in addition to dysmetria (15/36) or dysarthria (13/36). A substantial number of children (21/36) also had signs of encephalitis such as somnolence or seizures. In 10/36 (28 %) children the following autoantibodies (abs) were found: MOG-abs (n = 5) in serum, GFAPα-abs (n = 1) in CSF, GlyR-abs (n = 1) in CSF, mGluR1-abs (n = 1) in CSF and serum. In two further children, antibodies were detected only in serum (GlyR-abs, n = 1; GFAPα-abs, n = 1). MRI signal alterations in cerebellum were found in 30/36 children (83 %). Additional supra- and/or infratentorial lesions were present in 12/36 children, including all five children with MOG-abs. Outcome after a median follow-up of 3 months (range: 1 a 75) was favorable with an mRS ≤2 in 24/36 (67 %) after therapy. Antibody (ab)-positive children were significantly more likely to have a better outcome than ab-negative children (p = .022).

CONCLUSION

In nearly 30 % of children in our study with AC, a range of abs was found, underscoring that autoantibody testing in serum and CSF should be included in the work-up of a child with suspected AC. The detection of MOG-abs in AC does expand the MOGAD spectrum.

Effect of internal connection type and screw channel angle on the screw stability of anterior implant-supported zirconia crowns

OBJECTIVES

To investigate the effect of implant-abutment connection and screw channel angle on screw stability by comparing a newly introduced and an established connection, before and after cyclic loading.

MATERIALS AND METHODS

Implants (N = 44) with Torcfit (TF) or Crossfit (CF) connection were divided to be restored with a straight (CFS and TFS) or an angled screw access channel (CFA and TFA) titanium-base abutment (n = 11). CFA and TFA received screw-retained crowns, whereas CFS and TFS received hybrid zirconia abutments and cement-retained crowns. The initial torque value (ITV) of each complex (ITVI ) and removal torque value (RTV) after 24 h (RTVI ) were measured. Screws were replaced with new ones, ITVs were recorded again (ITVF ), and crowns were cyclically loaded (2.4 million cycles, 98 N) to measure RTVs again (RTVF ). Percentage torque loss was calculated. Data were analyzed (α = 0.05).

RESULTS

ITVs were similar among groups (p ≥ .089). CF led to higher RTVs (p ≤ .002), while CFS had higher RTVI than CFA (p = .023). After 24 h, CFS had lower percentage torque loss than TF, while CFA had lower percentage torque loss than TFA (p ≤ .011). After cyclic loading, CF led to lower percentage torque (p < .001).

CONCLUSION

The implant-abutment connection affected the removal torque values. However, no screw loosening occurred during cyclic loading, which indicated a stable connection for all groups. Screw access channel angle did not affect screw stability after cyclic loading.

Effect of triangular mesh resolution on the geometrical trueness of segmented CBCT maxillofacial data into STL format

OBJECTIVES

To determine the optimal level of mesh reduction that would maintain acceptable levels of geometrical trueness while also minimizing the impact on other parameters such as file size and processing time.

METHODS

Intraoral and extraoral maxillofacial defects were created on 8 cadaver heads and scanned by using a CBCT scanner (NewTom 3D Imaging, Verona). DICOM data were segmented to produce head (n=8) and skull models (n=8) saved as standard tessellation language (STL) files. A further processing of head models was preformed to produce face (n=8) and ear models (n=8). A mesh reduction process was performed for each STL model (reference, R0) by generating 50% (R1), 75% (R2), and 90% (R3) reductions. The 3 datasets were compared to the R0 file using 3D evaluation software (GOM Inspect) using a global best-fit algorithm, to calculate the root mean square (RMS) deviations. Statistical analyses were performed at a level of significance of α=0.05.

RESULTS

There was no 3D deviation after the 50% triangular mesh reduction in the 4 datasets. Minor 3D deviations were observed after 75% reduction, in all groups. After 90% reduction, higher 3D deviations were observed, and especially in head and skull. Statistically significant increase in 3D deviations was observed with higher degrees of mesh reduction (p < 0.001).

CONCLUSION

The resolution of CBCT-based maxillofacial defect models can be reduced up to 50%, with neglectable concern to inaccuracy.

CLINICAL SIGNIFICANCE

Accurate maxillofacial models can be obtained from CBCT DICOM files after segmentation and export as STL files, even when the mesh resolution is reduced up to 50%. This information can be valuable for practitioners and researchers working with 3D models of maxillofacial defects.

Tactile misfit detection ability at the implant-abutment interface of internal connection dental implants: an in-vitro study

OBJECTIVE

The aim of this in-vitro study was to investigate the tactile assessment ability at the implant impression-taking stage.

METHODS

Thirty clinicians (18 novices, 12 experts) were included for a tactile fit assessment by using a used/new probe (tip diameter 100 µm/20 µm). Six implant replicas and related impression copings of two internal connection implant systems were used, each with a perfect fit (0 µm) and defined vertical micro gaps of 8, 24, 55, 110 and 220 µm at the interface. Statistical analysis was performed using descriptive methods and non-parametric tests with a focus on specificity (ability to detect perfect fit), sensitivity (ability to detect misfit), and predictive values. P-values <5% were considered statistically significant.

RESULTS

The tactile assessment showed a mean total sensitivity for the Straumann and Nobel Biocare systems of 83% and 80% with a used probe, and 91% and 92% with a new probe, respectively. The mean total specificities were 33% and 20% with a used probe and 17% and 3% with a new probe, respectively. No statistical significance was observed between novice and expert clinicians concerning their tactile assessment ability.

CONCLUSIONS

The ability to detect a perfect fit (specificity) with a probe was very poor for both implant systems and impaired with the use of a new probe. The use of a new probe improved the gap detection ability (sensitivity) significantly at the expense of the specificity. A combination of additional chairside techniques with training and calibration could improve clinicians' ability to correctly assess the fit/misfit at the implant-abutment interface.

Group 4 ITI Consensus Report: Patient benefits following implant treatment in partially and fully edentulous patients

OBJECTIVES

The aim of Working Group 4 was to address patient benefits associated with implant dentistry. Focused questions on (a) dental patient-reported outcomes (dPROs), (b) improvement in orofacial function, and (c) preservation of orofacial tissues in partially and fully edentulous patients following provision of implant-retained/supported dental prostheses were addressed.

MATERIALS AND METHODS

Three systematic reviews formed the basis for discussion. Participants developed statements and recommendations determined by group consensus based on the findings of the systematic reviews. These were then presented and accepted following further discussion and modifications as required by the plenary of the 7th ITI Consensus Conference, taking place in 2023 in Lisbon, Portugal.

RESULTS

Edentulous patients wearing complete dentures (CD) experience substantial improvements in overall dPROs and orofacial function following treatment with either complete implant-supported fixed dental prostheses (CIFDP) or implant overdentures (IODs). With respect to dPROs, mandibular IODs retained by two implants are superior to IODs retained by one implant. However, increasing the number of implants beyond two, does not further improve dPROs. In fully edentulous patients, rehabilitation with CIFDP or IOD is recommended to benefit the preservation of alveolar bone and masseter muscle thickness.

CONCLUSIONS

Completely edentulous patients benefit substantially when at least the mandible is restored using an CIFDP or an IOD compared to CD. In fully edentulous patients, implant prostheses are the best option for tooth replacement. The availability of this treatment modality should be actively promoted in all edentulous communities, including those with limited access and means.

IMPACT OF LOADING PROTOCOL OF 2-IMPLANT BAR-RETAINED MANDIBULAR OVERDENTURES ON ORAL HEALTH-RELATED QUALITY OF LIFE: A RANDOMIZED CONTROLLED TRIAL

OBJECTIVES

Aim was to assess whether immediate loading (IL) is more effective than delayed loading (DL) for 2-implant bar-retained mandibular overdentures in terms of oral health-related quality of life (OHRQoL) improvement over a period of 24-month.

METHODS

In this randomized controlled trial, 32 edentulous patients (mean age: 65.7 ± 10.6 years, 50.0% female) were included. Potential participants had to be unsatisfied with the retention of their current mandibular complete denture and demanded implant treatment for inclusion in the study. OHRQoL was assessed with the 49-item Oral Health Impact Profile (OHIP) at baseline before treatment and 1, 3, 6, 12, and 24 months after implant loading and insertion of implant-retained bars for overdenture support. A mixed-effects model with patients as random effect and an unstructured covariance matrix was developed to address repeated outcome measurement.

RESULTS

Patients' OHRQoL impairment at baseline was substantial indicated by mean OHIP summary score of 45.1 points. OHIP summary scores decreased substantially from baseline to 1-month follow-up to a mean of 33.5 points (P = .020). OHRQoL further improved during study period indicated by OHIP summary score of 25.7 points at 24-month follow-up. Raw treatment effects (IL vs. DL) ranged from -1.2 OHIP points for 12-month follow-up to 5.8 OHIP points for 24-month follow-up. Assuming constant treatment and time effects, treatment effect was small and not statistically significant (-0.7 OHIP points; P= .918).

CONCLUSION

A 2-implant bar-retained mandibular overdentures substantially improves OHRQoL over a period of at least 24 months. There seems to be no significant effect of implant loading protocol.

Effect of polishing and denture cleansers on the surface roughness of new-generation denture base materials and their color change after cleansing

PURPOSE

To evaluate the effect of polishing and denture cleansers on the surface roughness (Ra ) of new-generation denture base materials that are additively, subtractively, and conventionally fabricated, while also assessing their color change after cleansing.

MATERIAL AND METHODS

One hundred and fifty disk-shaped specimens (Ø10 × 2 mm) were prepared from five denture base materials (one subtractively manufactured nanographene-reinforced prepolymerized polymethylmethacrylate (PMMA) (SM-GC), one subtractively manufactured prepolymerized PMMA (SM-PM), two additively manufactured denture base resins (AM-DT and AM-ND), and one heat-polymerized PMMA (CV) (n = 30). The Ra of the specimens was measured before and after conventional laboratory polishing, while color coordinates were measured after polishing. Specimens were then divided into three subgroups based on the denture cleanser: distilled water, 1% sodium hypochlorite (NaOCl), and effervescent tablet (n = 10). The Ra and color coordinates were remeasured after nine cleansing cycles over a period of 20 days. The CIEDE2000 formula was used to calculate the color differences (ΔE00 ). Two-way analysis of variance (ANOVA) was used to analyze the Ra values before (n = 30) and after (n = 10) cleansing, while repeated measures ANOVA was used to analyze the Ra of material-time point pairs within each denture cleanser (n = 10). ΔE00 data after denture cleansing was also analyzed by using two-way ANOVA (n = 10) (α = 0.05).

RESULTS

Before polishing, Ra varied significantly among the materials. SM-GC and SM-PM had the lowest and AM-ND the highest Ra values (P < 0.001). Polishing significantly reduced Ra of all materials (P < 0.001), and after polishing, Ra differences among materials were nonsignificant (P ≥ 0.072). Regardless of the denture cleanser, the Ra of AM-DT, AM-ND, and CV was the highest before polishing when different time points were considered (P < 0.001). After cleansing, AM-ND had the highest Ra of all the materials, regardless of the cleanser (P ≤ 0.017). AM-DT had higher Ra than SM-PM when distilled water (P = 0.040) and higher Ra than SM-GC, SM-PM, and CV when NaOCl was used (P < 0.001). The type of cleanser significantly influenced the Ra of AM-DT, AM-ND, and CV. For AM-DT, NaOCl led to the highest Ra and the tablet led to the lowest Ra (P ≤ 0.042), while for AM-ND, distilled water led to the lowest Ra (P ≤ 0.024). For CV, the tablet led to lower Ra than distilled water (P = 0.009). Color change varied among the materials. When distilled water was used, SM-GC had higher ΔE00 than SM-PM and AM-DT (P ≤ 0.034). When NaOCl was used, AM-ND had higher ΔE00 than SM-GC, SM-PM, and AM-DT, while CV and SM-GC had higher ΔE00 than SM-PM and AM-DT (P ≤ 0.039). Finally, when the tablet was used, AM-ND and CV had the highest ΔE00 , while AM-DT had lower ΔE00 than SM-GC (P ≤ 0.015).

CONCLUSIONS

The tested materials had unacceptable surface roughness (>0.2 μm) before polishing. Roughness decreased significantly after polishing (<0.2 μm). Denture cleansers did not significantly affect the surface roughness of the materials, and roughness remained clinically acceptable after cleansing (<0.2 μm). Considering previously reported color thresholds, AM-ND and CV had unacceptable color change regardless of the denture cleanser, and the effervescent tablet led to perceptible, but acceptable color change for SM-GC, SM-PM, and AM-DT.

Implant survival/success and peri-implant outcomes of titanium-zirconium mini implants for mandibular overdentures: Results from a 1-year randomized clinical trial

OBJECTIVE

To report the 1-year implant survival/success and peri-implant outcomes of mandibular overdentures retained by four titanium-zirconium mini implants (Straumann® Mini Implant System), and to assess how surgery and loading protocols influence these outcomes.

MATERIALS AND METHODS

A 2 × 2 factorial randomized clinical trial (RCT) tested the combined effects of two loading protocols (immediate or delayed) and two surgical approaches (flapless or flapped) on the success/survival of the mini implants, and peri-implant parameters (plaque, bleeding, sulcus depth, gingival position, and marginal bone loss). Outcomes were assessed up to 1-year after loading, and generalized estimating equations (GEEs) were used to analyze longitudinal and within-patient clustered data.

RESULTS

Two hundred and ninety-six implants were placed in 74 patients. The implant survival/success rates after 1 year were 100%, and no major biological complications were observed. After 1-year, descriptive data suggest no noticeable changes in plaque scores, whilst a reduction in bleeding scores at the 6-month and 1-year follow-ups compared to baseline. Good longitudinal stability was observed for the probing depth and gingival margin height measures. Overall mean marginal bone loss was 0.68 (±0.68) mm after 3 months and 0.89 (±0.75) mm after 1-year. The flapless protocol showed better results on soft tissue stability and health but a slightly higher risk for marginal bone loss.

CONCLUSION

The results of this RCT suggest that mandibular overdentures retained by this novel mini implant system represent a safe and predictable treatment option as confirmed by implant survival/success and peri-implant outcomes, even when flapless surgery and immediate loading protocols are adopted.

Influence of polishing technique and coffee thermal cycling on the surface roughness and color stability of additively and subtractively manufactured resins used for definitive restorations

PURPOSE

To evaluate how different polishing techniques and coffee thermal cycling effect the surface roughness and stainability of additively and subtractively manufactured resins used for definitive prostheses.

MATERIALS AND METHODS

Two additively manufactured composite resins (Crowntec, CT and VarseoSmile Crown Plus, VS) and a subtractively manufactured resin nanoceramic (Cerasmart, CS) were used to fabricate 90 rectangular-shaped specimens (14 × 12 × 1 mm) (n = 30). After baseline surface roughness (R_a ) measurements, specimens were divided into 3 groups based on the polishing technique; conventional polishing with a 2-stage polishing kit (CP) and surface sealant application (Optiglaze, OG or Vita Akzent LC, VA) (n = 10). After polishing, specimens were subjected to 10000 cycles of coffee thermal cycling. R_a and color coordinate measurements were performed after polishing and after coffee thermal cycling. Color difference (ΔE₀₀ ) was calculated. Scanning electron microscope images were taken at each time interval. Kruskal-Wallis or 1-way analysis of variance (ANOVA) were used to evaluate R_a of materials within each polishing-time interval pair and different polishing techniques within each material-time interval pair, while Friedman or repeated measures ANOVA were used to evaluate R_a at different time intervals within each material-polishing pair. ΔE₀₀ was assessed with 2-way ANOVA (α = .05).

RESULTS

Other than VA-after polishing (P = .055), tested materials had significantly different R_a within each polishing-time interval pair (P ≤ .038). When R_a differences among different polishing techniques within each material-time interval pair were considered, CS had differences after coffee thermal cycling, CT had differences before polishing and after coffee thermal cycling, and VS had differences within each time interval (P ≤ .038). When R_a differences among different time intervals within each material-polishing pair were considered, significant differences were observed among all pairs (P ≤ .016), except for CS-VA (P = .695) and VS-VA (P = .300). ΔE₀₀ values were affected by material and polishing technique interaction (P = .007).

CONCLUSIONS

R_a of CS was similar to or lower than the R_a of other materials, regardless of the time interval or polishing technique. CP mostly led to lower R_a than other polishing techniques, whereas VA resulted in a high R_a regardless of the material-time interval pair. Polishing reduced the R_a , while coffee thermal cycling was found to have a small effect. Among tested material-polishing pairs, only CS-VA had moderately unacceptable color change when previously reported threshold values were considered. This article is protected by copyright. All rights reserved.

Exploring preferences of older adults for dental services: A pilot multi-national discrete choice experiment

OBJECTIVES

To pilot an exploration of older adults' future preferences using discrete choice experiments to understand who should provide dental examinations and treatment, where these services should be provided, and participants' willingness to pay and willingness to travel.

BACKGROUND

The proportion of older adults in the general population is increasing and is recognised as a pressing public health challenge.

MATERIALS AND METHODS

Older people aged 65 years and over were recruited into this study from the UK, Switzerland and Greece. Drawing on earlier stakeholder engagement, a set of choice experiments are developed to explore the future preferences of older people for dental examinations and dental treatment, as they anticipated losing their independence. These were presented to the participants using a range of platforms, because of the COVID pandemic. Data were analysed in STATA using a random-effects logit model.

RESULTS

Two hundred and forty-six participants (median age 70 years) completed the pilot study. There was a strong preference across all countries for a dentist to undertake a dental examination (Greece: β = 0.944, Switzerland: β = 0.260, UK β = 0.791), rather than a medical doctor (Greece: β = -0.556, Switzerland: β = -0.4690, UK: β = -0.468). Participants in Switzerland and the UK preferred these examinations to be undertaken in a dental practice (Switzerland: β = 0.220, UK: β = 0.580) while participants in Greece preferred the dental examination to be undertaken in their homes (β = 1.172). Greek participants preferred dental treatment to be undertaken by a specialist (β = 0.365) in their home (β = 0.862), while participants from the UK and Switzerland preferred to avoid any dental treatment at home (Switzerland: β = -0.387; UK: β = -0.444). Willingness to pay analyses highlighted that participants in Switzerland and the UK were willing to pay more to ensure the continuity of future service provision at a family dental practice (Switzerland: β = 0.454, UK: β = 0.695).

CONCLUSION

Discrete choice experiments are valuable for exploring older people's preferences for dental service provision in different countries. Future larger studies should be conducted to further explore the potential of this approach, given the pressing need to design services that are fit for purpose for older people. Continuity of dental service provision is considered as important by most older people, as they anticipate losing their dependence.

Distortion assessment of different materials in full-arch dentate impressions in relation to operator experience: a comparative in vivo

PURPOSE

Evaluating the distortion probability in impressions of completely dentate arches when different impression materials are used in relation to operator experience.

MATERIAL AND METHODS

Twenty-eight students (group A) and 7 dentists (group B) performed 3 maxillary impressions on 28 students (participants), each using vinyl siloxane ether (VSE), polyether (PE), and irreversible hydrocolloid (IHC). Gypsum master casts were fabricated and subsequently digitized. Intraoral scans were taken as a control. Differences between master casts and intraoral scans were visualized by heatmaps and planar deviations were investigated. If planar deviations of >120 μm were found, the impression was rated as "distorted." An additional superimposition using the casts from VSE or PE was performed to confirm the presence of distortions. The relative number of surfaces with distortions in each impression was calculated. The procedure was repeated for a distortion threshold of 500 μm. The statistical analyses included measures ANOVA and post-hoc tests (a < 0.05).

RESULTS

When 120 μm was considered as the threshold for distortions, IHC impressions showed higher distortion probability than PE impressions in group A (P = 0.003) and group B (P < 0.0001). In group B only, PE showed a lower distortion probability than VSE (P = 0.02). There was no difference between the study groups (P = 0.42). Considering 500 μm as a threshold for distortions, there was no difference between impression materials (P = 0.17) or study groups (P = 0.53).

CONCLUSION

There were no statistic significant differences in relation to operator experience. Different impression materials had a significant impact on distortion probability. Polyether impressions showed the lowest distortion probability. Int J Prosthodont. 10.11607/ijp.8555.

Dental status and its correlation with polypharmacy and multimorbidity in a Swiss nursing home population: a cross-sectional study

OBJECTIVE

To assess the correlation between oral health status in terms of present teeth, implants, removable prostheses, and polypharmacy and/or multimorbidity in three Swiss nursing homes with affiliated or integrated dental care.

METHODS

A cross-sectional study was conducted in three Swiss geriatric nursing homes with integrated dental care. Dental information consisted of the number of teeth, root remnants, implants, and presence of removable dental prostheses. Furthermore, the medical history was assessed in terms of diagnosed medical conditions and prescribed medication. Age, dental status, polypharmacy, and multimorbidity were compared and correlated using t-tests and Pearson correlation coefficients.

RESULTS

One hundred eighty patients with a mean age of 85.5 ± 7.4 years were included of which a portion of 62% presented with multimorbidity and 92% with polypharmacy. The mean number of remaining teeth and remnant roots were 14.1 ± 9.9 and 1.0 ± 3.1, respectively. Edentulous individuals comprised 14%, and over 75% of the population did not have implants. Over 50% of the included patients wore removable dental prostheses. A negative correlation with statistical significance (p = 0.001) between age and tooth loss (r = - 0.27) was observed. Finally, there was a non-statistically correlation between a higher number of remnant roots and specific medications linked to salivary dysfunction; specifically antihypertensive medication and central nervous system stimulants.

CONCLUSION

The presence of a poor oral health status was associated with polypharmacy and multimorbidity among the study population.

CLINICAL RELEVANCE

Identifying elderly patients in need of oral healthcare in nursing homes is a challenge. In Switzerland, the collaboration of dentists and nursing staff is still improvable, but is urgently needed due to the demographic changes and raising treatment demand of the oldest portion of the population.

Assessment and Improvement of Masticatory Performance in Frail Older People: A Narrative Review

According to the World Health Organization (WHO), the estimated number of older adults is around 962 million and is projected to increase to 2.1 billion by 2050. The oral frailty concept is associated with gradual oral function loss in relation to aging. There is a need to emphasize the improvement of oral function based on an evaluation of masticatory performance in patients with various oral conditions or systemic diseases and especially in the frail elderly. The present narrative review presents an overview of the current state of the assessment and improvement of masticatory performance in frail older people. To fully encompass oral frailty, oro-facial hypofunction, or oro-facial fitness, dental Patient Reported Outcomes (dPROs) should be included; nevertheless, there are limited evidence-based rehabilitation approaches. The concept of oral frailty, oro-facial hypofunction, or oro-facial fitness should involve dental Patient Reported Outcomes (dPROs), and in this sense, there are only a few evidence-based rehabilitation procedures to improve oro-facial hypofunction besides prosthodontics. It must be considered that reduced neuroplastic capacity in old individuals might preclude a positive outcome of these strategies that might need to be accompanied by functional training and nutritional counseling.

Effect of number of supports and build angle on the fabrication and internal fit accuracy of additively manufactured definitive resin-ceramic hybrid crowns

OBJECTIVES

To evaluate the effect of number of supports and build angle on the fabrication and internal fit accuracy (trueness and precision) of additively manufactured resin-ceramic hybrid crowns.

METHODS

A mandibular first molar crown was designed and nested on the build platform of a printer either with a 30° angle between the occlusal surface and the build platform (BLS (less support) and BMS (more support)) or its occlusal surface parallel to the build platform (VLS (less support) and VMS (more support)) to fabricate additively manufactured resin-ceramic hybrid crowns (n=14). After fabrication, supports were removed by a blinded operator and all crowns were digitized with an intraoral scanner. Fabrication accuracy (overall, external, intaglio occlusal, occlusal, and marginal) was evaluated by using root mean square (RMS) method, while internal fit was evaluated with triple scan method. RMS, average gap, and precision of these data were analyzed (α= .05).

RESULTS

VLS had higher overall deviations than BLS and VMS (P≤.039). VMS had higher occlusal deviations than BLS (P=.033). While BMS and BLS had higher marginal deviations than VLS (P≤.006), BMS also had higher values than VMS (P=.012). BLS led to higher precision than VMS (intaglio occlusal and occlusal surfaces) and VLS (occlusal surface) (P≤.008). VLS led to higher precision than BMS (marginal surface) (P=.027). Average gap values were similar (P=.723); however, BLS resulted in higher precision than VLS (P=.018).

CONCLUSIONS

Considering their high marginal and occlusal surface trueness, and similar internal occlusal deviations and average gaps (trueness), clinical fit of resin-ceramic hybrid crowns fabricated with tested parameters may be similar. Reduced number of supports and angled orientation may lead to higher precision of fit.

CLINICAL SIGNIFICANCE

Tested resin-ceramic hybrid-printer pair may be used to fabricate crowns with reduced number of supports to maintain occlusal surface integrity without compromising the fabrication accuracy and fit.

Bond strength of additively manufactured composite resins to dentin and titanium when bonded with dual-polymerizing resin cements

STATEMENT OF PROBLEM

Additively manufactured composite resins for definitive restorations have been recently introduced. The bond strength between these composite resins and different substrates has not been extensively studied.

PURPOSE

The purpose of this in vitro study was to measure the shear bond strength (SBS) between additively manufactured composite resins and dentin and titanium substrates and compare those with the SBS between subtractively manufactured polymer-infiltrated ceramic and the same substrates (dentin and titanium), when different dual-polymerizing resin cements were used.

MATERIAL AND METHODS

One hundred and eighty cylinder-shaped specimens (Ø5×5 mm) were prepared from 3 materials recommended for definitive restorations: an additively manufactured composite resin (Crowntec [CT]); an additively manufactured hybrid composite resin (VarseoSmile Crown Plus [VS]); and a subtractively manufactured polymer-infiltrated ceramic (Enamic [EN]) (n=60). Specimens were randomly divided into six subgroups to be cemented to the two substrates (dentin and titanium; n=30) with 1 of 3 resin cements (RelyX Universal, Panavia V5, and Variolink Esthetic DC) (n=10). The restoration surface to be bonded was treated according to the respective manufacturer's recommendations. Dentin surfaces were treated according to the resin cement (Scotchbond Universal Plus Adhesive for RelyX Universal, Panavia V5 Tooth Primer for Panavia V5, and Adhese Universal for Variolink Esthetic DC), while titanium surfaces were airborne-particle abraded, and only the specimens paired with Panavia V5 were treated with a ceramic primer (Clearfil Ceramic Primer Plus). SBS was measured in a universal testing machine at a crosshead speed of 1 mm/min. Failure modes were analyzed under a microscope at ×12 magnification. Data were analyzed by using 2-way analysis of variance and Tukey honestly significant difference tests (α=.05).

RESULTS

When SBS to dentin was considered, only restorative material, as a main factor, had a significant effect (P<.001); EN had the highest SBS (P<.001), while the difference in SBS values of CT and VS was not significant (P=.145). As for SBS to titanium, the factors restorative material and resin cement and their interaction had a significant effect (P<.001). Within each resin cement, EN had the highest SBS to titanium (P<.001), and within each restorative material, Variolink resulted in the lowest SBS (P≤.010). Overall, EN and RelyX were associated with the highest SBS to titanium (P≤.013). Mixed failures were predominant in most groups.

CONCLUSIONS

Regardless of the substrate or the resin cement used, the subtractively manufactured polymer-infiltrated ceramic had higher shear bond strength than the additively manufactured composite resins. The SBS of the additively manufactured composite resins, whether bonded to dentin or titanium, were not significantly different from each other. Regardless of the restorative material, Variolink DC resulted in the lowest SBS for titanium surfaces.

First observations of core-transiting seismic phases on Mars

We present the first observations of seismic waves propagating through the core of Mars. These observations, made using seismic data collected by the InSight geophysical mission, have allowed us to construct the first seismically constrained models for the elastic properties of Mars' core. We observe core-transiting seismic phase SKS from two farside seismic events detected on Mars and measure the travel times of SKS relative to mantle traversing body waves. SKS travels through the core as a compressional wave, providing information about bulk modulus and density. We perform probabilistic inversions using the core-sensitive relative travel times together with gross geophysical data and travel times from other, more proximal, seismic events to seek the equation of state parameters that best describe the liquid iron-alloy core. Our inversions provide constraints on the velocities in Mars' core and are used to develop the first seismically based estimates of its composition. We show that models informed by our SKS data favor a somewhat smaller (median core radius = 1,780 to 1,810 km) and denser (core density = 6.2 to 6.3 g/cm³) core compared to previous estimates, with a P-wave velocity of 4.9 to 5.0 km/s at the core-mantle boundary, with the composition and structure of the mantle as a dominant source of uncertainty. We infer from our models that Mars' core contains a median of 20 to 22 wt% light alloying elements when we consider sulfur, oxygen, carbon, and hydrogen. These data can be used to inform models of planetary accretion, composition, and evolution.

Evaluation of the Oral Health Conditions and Oral Health-Related Quality of Life in a Community-Dwellers Population Aged ≥ 45 Years in the Canton of Bern: A Preliminary Pilot Study

OBJECTIVE

To evaluate oral health conditions and oral health-related quality of life in community-dwellers aged ≥ 45 years in the Canton of Bern, Switzerland.

MATERIALS AND METHODS

One hundred subjects (63% males; mean age: 73 years), selected randomly using a cluster procedure within the Canton of Bern, underwent a clinical oral examination after completing questionnaires on socio-economic level, medical history, oral health behaviour, and Geriatric Oral Health Assessment Index (GOHAI). Descriptive analyses and multinomial regression models were applied to investigate the association between oral health diseases (dental caries and periodontitis) and specific participant characteristics.

RESULTS

The mean number of decayed, missing, and filled teeth (DMFT) was 0.30, 4.20, and 8.75, respectively; the mean DMFT score = 13.35. Dental caries prevalence (ICDAS > 0) was 15% and periodontitis prevalence was 46%. Logistic regression models revealed that living in an urban area was associated with lower odds (OR 0.03, _95%CI 0.00-0.36) of having periodontal disease. Male gender was associated with lower odds for dental caries (OR 0.31, _95%CI 0.09-1.01) and total lack of professional tooth cleaning was associated with higher odds for dental caries (OR 41.99, _95%CI 0.01-0.38). Ordinal logistic regression revealed that both the presence of dental caries (RR 12.80, _95%CI 1.47-111.20) and periodontal disease (RR 6.91, _95%CI 1.16-84.00) were statistically significantly associated with rheumatoid arthritis.

CONCLUSION

Within the study limitations, untreated dental caries and periodontal disease are prevalent in the Swiss population, despite the high level of self-performed oral hygiene and access to the dental care system.

Implant-supported fixed dental prostheses with cantilever extensions: State of the art and future perspectives

Partial fixed dental prostheses supported by dental implants have become a reliable long-term treatment option. Nevertheless, the replacement of two adjacent missing teeth, irrespective of location, still represents a clinical challenge. To overcome this, the use of fixed dental prostheses with cantilever extensions has gained popularity with a view to limiting morbidity, reducing costs and avoiding major surgical interventions prior to implant placement. The present review summarises the level of evidence for the use of fixed dental prostheses with cantilever extensions both in the posterior and anterior regions and indicates the advantages and disadvantages of each treatment, focusing on available medium- to long-term outcomes.

Effect of computer-aided design and computer-aided manufacturing technique on the accuracy of fixed partial denture patterns used for casting or pressing

OBJECTIVES

To evaluate the effect of additive and subtractive manufacturing on the accuracy (trueness and precision) of fixed partial denture patterns (FPDPs) used for casting or pressing.

MATERIALS AND METHODS

A 3-unit complete coverage FPD on mandibular right first premolar and first molar teeth was virtually designed. Using the design data, FPD patterns were fabricated from an additively manufactured resin (PR, ProArt Print Wax) and 2 CAD-CAM wax discs (YW, ProArt CAD Wax Yellow and BW, ProArt CAD Wax Blue) (n = 10). Each pattern was then digitized with a scanner (CEREC Primescan) and evaluated for 3D surface deviation at 4 different surfaces (overall, external, marginal, and intaglio surfaces) by using a 3D analysis software (Medit Link). Root mean square (RMS) values were automatically calculated. Data were analyzed by using Kruskal-Wallis and Dunn's post hoc tests for trueness and precision (α= 0.05).

RESULTS

Significant differences were found among the RMS values for overall (P<.001) and each surface (P≤.040) evaluated. PR had the highest overall (P≤.011) and intaglio surface (P≤.01) deviations, while the difference between YW and BW was not significant (P≥.199). PR had the highest (P≤.027) and BW had the lowest (P≤.042) external surface mean RMS values. BW had higher mean marginal RMS value than YW (P=.047). For precision, significant differences were observed among test groups only for marginal RMS values (P=.002). PR had lower precision than BW (P=.002).

CONCLUSIONS

BW and YW FPDPs mostly had higher trueness compared with PR FPDPs. However, considering relatively smaller deviations at marginal and intaglio surfaces and the fact that patterns mostly had similar precision, clinical fit of FPDs fabricated by using tested patterns may be similar.

CLINICAL SIGNIFICANCE

Definitive 3-unit fixed partial dentures fabricated by using tested patterns may be similar. However, FPDs fabricated with tested additively manufactured resin patterns might result in more chairside adjustments than those fabricated with tested subtractively manufactured wax patterns.

Effect of coffee thermocycling on the surface roughness and stainability of nanographene-reinforced polymethyl methacrylate used for fixed definitive prostheses

STATEMENT OF PROBLEM

A nanographene-reinforced polymethyl methacrylate (PMMA) has been introduced for definitive prostheses. However, knowledge on the surface roughness and stainability of this material is lacking.

PURPOSE

The purpose of this in vitro study was to compare the surface roughness and stainability of nanographene-reinforced PMMA with those of a prepolymerized PMMA and a reinforced composite resin after coffee thermocycling.

MATERIAL AND METHODS

Disk-shaped specimens (Ø10×1.5-mm) were prepared from 3 different A1-shade millable resins (prepolymerized PMMA [M-PM; PMMA]; nanographene-reinforced PMMA [G-CAM; G-PMMA]; reinforced composite resin [Brilliant Crios; RCR]). Surface roughness (R_a) values were measured before and after conventional polishing by using a noncontact profilometer. Initial color coordinates were measured over a gray background with a spectrophotometer after polishing. Specimens were then thermocycled in coffee for 5000 cycles. Measurements were repeated after coffee thermocycling, and color differences (ΔE₀₀) were calculated. R_a values among different time intervals were analyzed by using either the Friedman and Dunn tests (RCR) or repeated measures analysis of variance (ANOVA) and Bonferroni corrected paired samples t tests (PMMA and G-PMMA), while R_a values within a time interval were analyzed by using either the Kruskal-Wallis and Dunn tests (before polishing) or 1-way ANOVA and Tukey HSD (after polishing) or Tamhane T2 tests (after coffee thermocycling). ΔE₀₀ values were analyzed by using 1-way ANOVA and Tukey HSD tests, while color coordinates of the specimens after polishing and after coffee thermocycling were compared by using paired samples t tests (α=.05).

RESULTS

All materials had their highest R_a values before polishing (P≤.011), while differences after polishing and after coffee thermocycling values were nonsignificant (P≥.140). PMMA had higher R_a than RCR before polishing (P=.002), and RCR had higher values than G-PMMA after polishing and after coffee thermocycling (P≤.023). RCR had the highest ΔE₀₀ (P<.001). Polishing increased the b∗ values of PMMA, and coffee thermocycling increased the a∗ values of G-PMMA and all values of RCR (P≤.012).

CONCLUSIONS

The tested materials had similar and acceptable surface roughness after polishing. The surface roughness of materials was not affected by coffee thermocycling. Considering the reported color thresholds, all materials had acceptable color change, but the computer-aided design and computer-aided manufacturing composite resin had perceptible color change after coffee thermocycling.

Willingness to accept or refuse mandibular implant overdenture treatment: A prospective study on edentulous enrolled in a clinical trial

BACKGROUND

Several complete denture wearers have major complaints and may be benefitted from implant treatment. However, the factors that shape the demand for and utilization of implants need further investigation.

OBJECTIVE

The aim was to evaluate edentulous patient's willingness to accept or refuse the offer and provision of implant-retained treatment.

METHODS

As part of a clinical trial, edentulous subjects were offered a mandibular overdenture retained by four mini-implants opposing a conventional maxillary denture. Treatment was offered without any financial costs for the patients. Patients' level of interest in receiving treatment was assessed using a 5-point Likert scale, and they were asked to respond to a list of reasons that led to their decision to accept or refuse implants. Those who refused implants received conventional prosthodontic interventions as required, and those who accepted implant treatment underwent surgical planning and implant placement.

RESULTS

Of 175 eligible subjects, 147 accepted the offer of treatment and were invited to take part in the study (69.4% women, mean age 67.4 ± 10.0 years). Overall, 111 patients (75.5%) expressed a positive intention to undergo implant treatment at the initial contact. Implant treatment was performed for 56.3% (9/16) of those who answered 'probably yes' about their level of interest in implant treatment on the Likert scale, and 69.6% (64/92) of 'certainly yes' (p < .001). Older subjects were less likely to receive implants (OR = 0.93; p = .036), whilst those with a positive intention towards implants (OR = 3.15; p = .001), those previously treated by the dental team (OR = 7.89; p < .001), and who actively demanded implants (OR = 18.1; p < .001) were more likely to accept treatment. Improved chewing was the most common reason for accepting implants, whilst fear of surgery was the most reported reason for refusal.

CONCLUSION

Refusal of implants was high among edentate patients even when financial costs were removed. Patients' initial attitude towards acceptance is a key factor in the demand for and uptake of implant therapy.

Double-Crown Prosthesis Retention Using Polyetherketoneketone (PEKK): An In Vitro Study

PURPOSE

To assess the retentive force of telescopic crowns using polyetherketoneketone (PEKK) high-performance polymer in relation to conventional materials over a long period of time in an in vitro setting.

MATERIALS AND METHODS

Thirty-six sets of primary and secondary crowns were fabricated as per the double crown-retained prostheses approach. Six samples were included in each of the five test groups (1: zirconia/PEKK [Zr/PEKK]; 2: titanium/PEKK [Ti/PEKK]; 3: cobalt-chrome/PEKK [CoCr/PEKK]; 4: PEKK/PEKK; and 5: gold/PEKK [Au/PEKK]) and the single control group (gold/galvano-gold [Au/GA]). The insertion-removal test was performed for 20,000 cycles, and the surface condition was observed. Retentive forces were analyzed using two-way ANOVA (α<0.05).

RESULTS

The retention forces in groups Zr/PEKK and Ti/PEKK significantly decreased over time (group 1: p = 0.035 and group 2: p = 0.001), whereas retentive force increased significantly in groups PEKK/PEKK, Au/PEKK, and control (group 4: p = 0.001, group 5: p = 0.008, and control: p = 0.042). Similar wear was observed on the primary crown in groups PEKK/PEKK, gold/PEKK, and control.

CONCLUSIONS

Groups PEKK/PEKK and Au/PEKK showed a transition of retentive force similar to the control group. Groups PEKK/PEKK and Au/PEKK had similar wear on the surface compared to control. Therefore, PEKK has a promising clinical potential.

Masticatory performance in oral function assessment: Alternative methods

BACKGROUND

Masticatory function declines with age or disease, implicating a poor chewing efficiency and an often-unconscious change for a less healthy, yet easy to chew diet. Timely screening of masticatory function may foster an early-onset diagnosis and potential treatment. The aim of this study was to compare alternative diagnostic tools for masticatory function to a Jelly-scan test.

MATERIALS AND METHODS

Patients aged 70 years and older who were hospitalised for rehabilitation were recruited for this study. A total of four different tests for masticatory function were administered. The Japanese Society of Gerodontology glucose extraction test (Jelly-scan) was used as reference to compare a colour-changing gum test (Gum1-colour) as well as a mixing ability test with a visual (Gum2-visual) and opto-electronical (Gum2-digital) analyses. Receiver operating characteristic (ROC) curves were used to establish the discriminative value, kappa-values were used to estimate individual agreements and correlations were verified using Spearman's tests.

RESULTS

Sixty-one patients (Men n = 23, Women n = 38) aged 82.4 ± 6.8 years participated in the experiments. The average number of natural teeth was 16.5 ± 10.5, 34.4% of the participants wore removable dentures. For all tests, the sum of sensitivity and specificity was >150%. All test correlated with Jelly-scan (absolute Rho >0.5). With Jelly-scan 51 participants (83.6%) were diagnosed with "masticatory hypofunction". After reducing the cut-off value of the test from 100 mg/dL to 65 mg/dL, only 33 participants (54%) fulfilled the diagnosis. This post-hoc analysis increased the sensitivity of the Gum2-tests and the agreement to kappa >0.5 for all three tests.

CONCLUSION

All three tests can be considered useful screening alternatives. In its original version, Jelly-scan may tend to over-diagnose masticatory hypofunction, hence a novel cut-off with better agreement between tests is suggested.

Mandibular bone characteristics, drilling protocols, and final insertion torque for titanium-zirconium mini-implants for overdentures: A cross-sectional analysis

OBJECTIVE

The aim of this study was to assess the final insertion torque values achieved using site-specific drilling protocols for a novel mini implant system for removable complete overdentures. Anatomical and technical factors influencing final insertion torque were recorded and analyzed.

MATERIAL AND METHODS

Participants were randomized to two surgical protocol groups (flapped or flapless) and all received four mini implants (Straumann® mini implant system; Straumann AG) in the anterior mandible, using a 1.6 mm needle drill and a 2.2 mm pilot drill for the implant bed site preparation. The final insertion torque was recorded as the main outcome variable during surgery. Bone type, radiographical bone density, ridge form, implant length, and the drilling protocol were considered as independent variables. Descriptive statistics, generalized estimating equations (GEE) regression, and heatmap charts were used for data analyses.

RESULTS

A total of 296 mini implants were placed in 74 patients (mean age = 64.1 ± 8.0; 64.9% female) using flapless (n = 37) or flapped (n = 37) surgeries. Mean final insertion torque was 55.8 ± 18.4 Ncm (10.5% > 35 Ncm, 48.9% between 35 and 65 Ncm, and 40.6% > 65 Ncm). The needle drill was used in only 43.9% of the implant bed sites. Higher final torque values were observed for higher bone densities (bone type I > II > III, and D1-D2 > D3-D4), highly resorbed ridge forms (5-6 > 3-4), flapped surgeries, and male patients. However, regression models showed that the likelihood of achieving optimal insertion torque (≥35 and ≤65 Ncm) was higher for females (OR = 2.14; 95%CI = 1.14-4.01; p = 0.018), ridge forms 3-4 (OR = 2.87; 95%CI = 1.05-7.85; p = 0.040), and flapless surgeries (OR = 1.96; 95%CI = 1.09-3.51; p = 0.024).

CONCLUSIONS

Sufficient primary stability for immediate loading was achieved for the majority of the mini implants placed. Surgical implant bed preparation should be site-specific to achieve optimal primary stability for immediate loading while avoiding excessive insertion torque.

O-Ring Attachments on One-Piece Mini Dental Implants: In Vitro Analysis of Retention Force Reproducibility Using Different Pristine Matrix-O-Ring Combinations

PURPOSE

To analyze the influence of pristine matrix and O-ring dimensions on retention force and reproducibility in single one-piece mini dental implants (MDIs) with ball patrices under in vitro conditions.

MATERIALS AND METHODS

Three different matrix and O-ring combinations (MH1-MH3) were evaluated (n = 50 per group) on 1.8-mm-diameter implants. The matrices were manually mounted on the implants and were subsequently removed in a vertical linear manner using a metal pin with two strain gauges, recording the maximum force during disconnection. After five disconnections, the O-rings were exchanged, and the mean retention force was calculated, resulting in 50 values for each matrix and O-ring combination. Mean retention forces, SDs, and 95% CI were calculated. Analysis of variance was used to test the global differences, and post hoc pairwise comparisons were subsequently applied. The level of significance was set to P < .05.

RESULTS

ANOVA (global P < .0001) and pairwise comparisons (all P < .0001) demonstrated statistically significant differences among the three different matrix and O-ring combinations, with mean values of 5.18 N (MH 1), 6.73 (MH 2), and 9.08 (MH 3). Within each combination, retention force variations of > 1 N could not be demonstrated; ie, by exchanging O-rings, a similar retention force can be reestablished.

CONCLUSION

Matrix and O-ring dimensions have a significant influence on retention forces in one-piece MDIs. Pristine O-rings demonstrated highly reproducible initial retention forces in all matrices.

Effect of Abutment Cooling on Reverse Torque Values of Abutment Screws: An In Vitro Study

Purpose: To evaluate the effect of cooling on the reverse torque values of different abutments in bone-level and tissue-level implants. The null hypothesis was that there would be no difference in reverse torque values of abutment screws when cooled and uncooled implant abutments were compared. Materials and Methods: Bone-level and tissue-level implants (Straumann, each n = 36) were placed in synthetic bone blocks and subdivided into three groups (each n = 12) based on the abutment type (titanium base, cementable abutment, abutment for screw-retained restorations). All abutment screws were tightened to 35 Ncm torque. In half of the implants, a dry ice rod was applied on the abutments close to the implant-abutment connection for 60 seconds before untightening the abutment screw. The remaining implant-abutment pairs were not cooled. The maximum reverse torque values were recorded using a digital torque meter. The tightening and untightening procedure was repeated three times for each implant including cooling for the test groups, resulting in 18 reverse torque values per group. Two-way analysis of variance (ANOVA) was used to analyze the effect of cooling and abutment type on the measurements. Post hoc t tests were used to make group comparisons (α = .05). The P values of post hoc tests were corrected for multiple testing using the Bonferroni-Holm method. Results: The null hypothesis was rejected. Cooling and abutment type significantly affected the reverse torque values in bone-level implants (P = .004) but not in tissue-level implants (P = .051). The reverse torque values of bone-level implants significantly decreased after cooling (20.31 ± 2.55 Ncm vs 17.61 ± 2.49 Ncm). Overall mean reverse torque values were significantly higher in bone-level implants compared to tissue-level implants (18.96 ± 2.84 Ncm vs 16.13 ± 3.17 Ncm; P < .001). Conclusion: Cooling of the implant abutment led to a significant decrease in reverse torque values in bone-level implants and may therefore be recommended as a pretreatment before the application of procedures to remove a stuck implant part.

Trueness of crowns fabricated by using additively and subtractively manufactured resin-based CAD-CAM materials

STATEMENT OF PROBLEM

Advancements in digital dental technologies have enabled the use of different resin-based materials that can be fabricated either additively or subtractively. However, knowledge on the fabrication trueness of these materials is scarce.

PURPOSE

The purpose of this in vitro study was to investigate the trueness of crowns fabricated by using different resin-based computer-aided design and computer-aided manufacturing (CAD-CAM) materials.

MATERIAL AND METHODS

A complete crown for a mandibular right first molar with a 30-μm cement space was designed in standard tessellation language (STL) format. This master STL (MC-STL) was used to fabricate 40 complete crowns with 4 different resin-based CAD-CAM materials and either additive (Crowntec [MS]) or subtractive techniques (Brilliant Crios [BC], breCAM.monoCOM [PMMA], and G-CAM [GR]; n=10). All crowns were digitized with an intraoral scanner (CEREC Primescan SW 5.2) to generate their STL files (TC-STLs). MC-STL and TC-STLs were transferred into a 3-dimensional analysis software program (Medit Link v2.4.4), and a trueness (overall, external, occlusal, intaglio occlusal, and marginal) analysis was performed by using the root mean square (RMS) method. The Kruskal-Wallis and Dunn tests were performed to analyze data (α=.05).

RESULTS

The test groups had significantly different deviations on all surfaces (P≤.001). MS crowns had higher overall (P≤.007) and external surface (P≤.001) deviations than GR and PMMA crowns, while the differences between GR and PMMA crowns were not significant (P≥.441). BC crowns had higher external surface deviations than GR crowns (P=.005), higher occlusal deviations than GR and MS crowns (P≤.007), and higher intaglio occlusal deviations than GR and MS crowns (P≤.009). However, BC crowns had lower marginal deviations than MS and GR crowns (P≤.018).

CONCLUSIONS

The brand of resin-based CAD-CAM materials affected the trueness of crowns. Additively manufactured crowns (MS) mostly had lower overall and external surface trueness than the other groups. Nevertheless, the deviation values of occlusal, intaglio occlusal, and marginal trueness were generally small; thus, the effect of the tested materials on clinical crown fit may be negligible.

Global prevalence of edentulism and dental caries in middle-aged and elderly persons: A systematic review and meta-analysis

OBJECTIVE

The aim of the study was to analyze data collected from studies worldwide on the prevalence of edentulism and dental caries, in community-dwellers aged ≥ 45 years.

DATA

Inclusion criteria; participants aged ≥ 45 years, community-dwellers. Exclusion criteria; participants aged < 45 years, in nursing homes, data obtained from dental clinics or pre-2005. The quality assessment tool by The National Heart, Lung and Blood Institute for Observational Cohort and Cross-sectional studies was used. Meta-analysis using the random-effects model (95% confidence interval) was done with data on participants who were edentulous and/or had active dental caries and stratified by regions of the world, age and Gross National Income per capita. Limitations in the data arose from several factors such as design of the studies included differences in socioeconomic status and access to health care among different countries.

SOURCES

Embase, MEDLINE via Pubmed and Scopus, manual searches, from January 2016, restricted to English. Experts from different countries were contacted to identify National oral health surveys (NOHS) conducted from 2010 onwards.

STUDY SELECTION

Eighty-six papers and seventeen NOHS were selected for data extraction. Majority of the studies (n = 69) were cross-sectional and of fair quality. 1.1%-70%, 4.9% - 98% prevalence of edentulism and dental caries, respectively. 22%, 45% estimated random-effects pooled prevalence of edentulism and dental caries, respectively.

CONCLUSIONS

Within the limitations of this study, the findings indicate that untreated dental caries and tooth loss are prevalent on a global level with wide variations among different countries, age groups and socioeconomic status.

CLINICAL SIGNIFICANCE

The findings demonstrate the reality of the new cohort of older adults, with higher tooth retention implying more dental caries incidence and the need for different care strategies to ensure better oral health. Large variations and difficulty in making comparisons among different countries highlight the need for more standardized, regular research.

Relationship between tongue pressure and handgrip strength: A systematic review and meta-analysis

OBJECTIVES

Muscle strength decreases with age, causing a decline in physical and oro-facial function. However, the impact of physiological and pathophysiological factors on tongue pressure (TP) has not been clarified. The purpose of this systematic review and meta-analysis was to compare and analyse TP and handgrip strength (HGS) between individuals aged <60 and ≥60 years, gender and need for care (independent older adults (IC) and older adults receiving nursing care (NC)). Furthermore, the effect of HGS in physical function on TP was examined.

METHODS

Human clinical studies reporting HGS and TP were searched systematically using PubMed and Ichushi-Web published from 1969 to Nov 2021. Random-effects meta-regressions were performed to compare between subgroups and to examine the association between HGS and TP (α < .05).

RESULTS

Forty-four studies with a total of 10 343 subjects were included. TP and HGS values were significantly higher in people aged <60 years relative to ≥60 years and in IC relative to NC (all p < .001). Regarding gender, there was no significant difference in TP (p = .370). However, a significant gender-dependent difference in TP was observed in people aged <60 years (p < .001), but not in aged ≥60 years in IC group (p = .118) and aged ≥60 years in NC group (p = .895). There was a significant positive correlation of HGS and TP (p < .001).

CONCLUSIONS

Similar to decrease in HGS, age-related sarcopaenia seems to have an effect on oro-facial muscles like the tongue. Research on rehabilitation measures for oro-facial muscle strength, similar to HGS might be beneficial to improve the personally acquired oro-facial potential.

Surface waves and crustal structure on Mars

We detected surface waves from two meteorite impacts on Mars. By measuring group velocity dispersion along the impact-lander path, we obtained a direct constraint on crustal structure away from the InSight lander. The crust north of the equatorial dichotomy had a shear wave velocity of approximately 3.2 kilometers per second in the 5- to 30-kilometer depth range, with little depth variation. This implies a higher crustal density than inferred beneath the lander, suggesting either compositional differences or reduced porosity in the volcanic areas traversed by the surface waves. The lower velocities and the crustal layering observed beneath the landing site down to a 10-kilometer depth are not a global feature. Structural variations revealed by surface waves hold implications for models of the formation and thickness of the martian crust.

Effect of thermal cycling on the flexural strength and hardness of new-generation denture base materials

PURPOSE

To evaluate the flexural strength and Vickers microhardness of different CAD-CAM denture base materials.

MATERIALS AND METHODS

Sixty rectangular specimens (64×10×3.3 ±0.2 mm) were fabricated from 3 different denture base materials (G-CAM, Graphene-reinforced polymethylmethacrylate, GC), Ivotion Base (Prepolymerized polymethylmethacrylate, IV), and Denturetec (3D-printed resin, DT) either by using additive (DT) or subtractive manufacturing (IV and GC). Specimens of each group were divided into 2 subgroups (thermal cycled or non-thermal cycled, n = 10/group). Non-thermal cycled specimens were stored in distilled water at 37°C for 24 hours and subjected to 3-point flexural strength test with a universal testing machine. Thermal cycled specimens were initially evaluated for Vickers microhardness and subjected to thermal cycling (10000 cycles at 5-55°C). Vickers microhardness values were re-measured, and the specimens were subjected to 3-point flexural strength test. Data were analyzed by using 2-way analysis of variance and Bonferroni-corrected Tukey honestly significant difference tests (α = .05).

RESULTS

Material type and condition significantly affected flexural strength (P≤.004), whereas their interaction was nonsignificant (P = .778). Overall flexural strength of the materials in decreasing order was GC, IV, and DT (P<.001), regardless of the condition. Material had a higher effect on flexural strength (ηp² = .731) than thermal cycling (ηp² = .142). The effect of the interaction between the material type and thermal cycling on Vickers microhardness was significant (P<.001). GC had the highest microhardness before and after thermal cycling (P<.001). IV had higher microhardness than DT before thermal cycling (P<.001). However, DT and IV showed similar microhardness after thermal cycling (P = .665). Thermal cycling decreased the microhardness of GC and IV (P≤.022), whereas its effect on DT's microhardness was nonsignificant (P = .538). Material type had the highest effect on microhardness (ηp² = .864) followed by the interaction between the main factors (ηp² = .258).

CONCLUSIONS

Graphene-reinforced polymethylmethacrylate had the highest flexural strength and Vickers microhardness values, regardless of thermal cycling. Thermal cycling reduced the flexural strength of all resins. Thermal cycling reduced the microhardness of milled polymethylmethacrylate, but not that of 3D-printed resin. This article is protected by copyright. All rights reserved.