Efficient and bright warm-white electroluminescence from lead-free metal halides

Efficient Large-Area (81 cm2) Ternary Copper Halides Light-Emitting Diodes with External Quantum Efficiency Exceeding 13% via Host-Guest Strategy

Ternary copper (Cu) halides are promising candidates for replacing toxic lead halides in the field of perovskite light-emitting diodes (LEDs) toward practical applications. However, the electroluminescent performance of Cu halide-based LEDs remains a great challenge due to the presence of serious nonradiative recombination and inefficient charge transport in Cu halide emitters. Here, the rational design of host-guest [dppb]2Cu2I2 (dppb denotes 1,2-bis[diphenylphosphino]benzene) emitters and its utility in fabricating efficient Cu halide-based green LEDs that show a high external quantum efficiency (EQE) of 13.39% are reported. The host-guest [dppb]2Cu2I2 emitters with mCP (1,3-bis(N-carbazolyl)benzene) host demonstrate a significant improvement of carrier radiative recombination efficiency, with the photoluminescence quantum yield increased by nearly ten times, which is rooted in the efficient energy transfer and type-I energy level alignment between [dppb]2Cu2I2 and mCP. Moreover, the charge-transporting mCP host can raise the carrier mobility of [dppb]2Cu2I2 films, thereby enhancing the charge transport and recombination. More importantly, this strategy enables a large-area prototype LED with a record-breaking area up to 81 cm2, along with a decent EQE of 10.02% and uniform luminance. It is believed these results represent an encouraging stepping stone to bring Cu halide-based LEDs from the laboratory toward commercial lighting and display panels.

Centimeter-Sized Single Crystals of Tetrahedral Manganese (II) Halide Hybrids for Wide-Color Gamut Backlighting Displays

Phosphors with narrow-band green emissions and high photoluminescent quantum efficiency (PLQY) are significantly required for backlighting displays with wider color gamut. In this work, two centimeter-sized manganese (II) halide single crystals TMG2MnCl4 and TMG2MnBr4 (TMG = 1,1,3,3-tetramethylguanidine) are synthesized, exhibiting bright narrow-band green emissions with high PLQYs up to 62% and 90%, respectively. The narrow-band green light emission is located at 520 nm with a full-width at half-maximum (FWHM) of only 57 nm. The photoluminescence mechanisms of two single crystals are elaborated. Two white-light-emitting diodes for backlighting displays (BD-WLEDs) based on them are fabricated, exhibiting the widest color gamut of 122% National Television Standards Committee (NTSC), and a luminous efficacy reached ≈93 lm W-1 with excellent luminescence stability at high temperatures. These properties indicate the potential applications of tetrahedral manganese (II) hybrids in wide-color gamut backlighting displays.

Crown-Assisted CsCu2I3 Growth and Trap Passivation for Perovskite Light-Emitting Diodes

Copper (Cu)-based perovskites are promising for lead-free perovskite light-emitting diodes (PeLEDs). However, it remains a significant challenge to achieve high performance devices due to the nonradiative loss caused by the disordered crystallization and lack of passivation. Crown ethers are known to form host-guest complexes by the interaction between C-O-C groups and certain cations, and 18-crown-6 (18C6) with an appropriate complementary size can interact with Cs+ and Cu+ cations. Herein, we studied the interaction between CsCu2I3 and two crowns with the same cyclic size, 18C6 and dibenzo-18-crown-6 (D18C6). Particularly, D18C6 can reduce the nonradiative recombination rate of CsCu2I3 film by passivating the defects and optimizing the film morphology effectively. The room mean square (RMS) decreased from 5.06 to 2.95 nm, and the PLQY was promoted from 4.71% to 19.9%. Besides, D18C6 can also decrease the barrier of hole injection. The PeLEDs based on D18C6-modified CsCu2I3 realized noticeable improvement with a maximum luminance and EQE of 583 cd/m2 and 0.662%, respectively.

Atomically Contacted Cs3Bi2Br9 QDs@UiO-66 Composite for Photocatalytic CO2 Reduction

Metal halide perovskite quantum dots (QDs) are widely studied in the field of photocatalytic CO2 due to their strong light absorption and long carrier migration length. However, it can not exhibit high catalytic performance because of the radiative recombination and the lack of effective catalytic sites. Metal organic frameworks (MOFs) encapsulated QDs can not only solve the aforementioned problems, but also maintain their own unique characteristics with ultra-high specific surfaces area and abundant metal sites. In this work, lead-free bismuth-based halide perovskite QDs are encapsulated into Zr-based MOF (UiO-66), which combines the advantages with high power conversion efficiency of QDs and the high surface area and porosity of UiO-66. In addition, benefiting from the close contact between the Cs3Bi2Br9 QDs and the UiO-66 enables the photogenerated electrons in the QDs to be rapidly transferred to the MOF. As a result, the Cs3Bi2Br9@UiO-66 composite exhibits a higher yield for photocatalytic CO2 reduction than that of the prepared large-sized composite of Cs3Bi2Br9 and UiO-66.

Efficient and bright broadband electroluminescence based on environment-friendly metal halide nanoclusters

Broadband electroluminescence based on environment-friendly emitters is promising for healthy lighting yet remains an unprecedented challenge to progress. The copper halide-based emitters are competitive candidates for broadband emission, but their high-performance electroluminescence shows inadequate broad emission bandwidth of less than 90 nm. Here, we demonstrate efficient ultra-broadband electroluminescence from a copper halide (CuI) nanocluster single emitter prepared by a one-step solution synthesis-deposition process, through dedicated design of ligands and subtle selection of solvents. The CuI nanocluster exhibits high rigidity in the excitation state as well as dual-emissive modes of phosphorescence and temperature-activated delayed fluorescence, enabling the uniform cluster-composed film to show excellent stability and high photoluminescent efficiency. In consequence, ultra-broadband light-emitting diodes (LEDs) present nearly identical performance in an inert or air atmosphere without encapsulation and outstanding high-temperature operation performance, reaching an emission full width at half maximum (FWHM) of ~120 nm, a peak external quantum efficiency of 13%, a record maximum luminance of ~50,000 cd m-2, and an operating half-lifetime of 137 h at 100 cd m-2. The results highlight the potential of copper halide nanoclusters for next-generation healthy lighting.

Mapping Uncharted Lead-Free Halide Perovskites and Related Low-Dimensional Structures

Research on perovskites has grown exponentially in the past decade due to the potential of methyl ammonium lead iodide in photovoltaics. Although these devices have achieved remarkable and competitive power conversion efficiency, concerns have been raised regarding the toxicity of lead and its impact on scaling up the technology. Eliminating lead while conserving the performance of photovoltaic devices is a great challenge. To achieve this goal, the research has been expanded to thousands of compounds with similar or loosely related crystal structures and compositions. Some materials are "re-discovered", and some are yet unexplored, but predictions suggest that their potential applications may go beyond photovoltaics, for example, spintronics, photodetection, photocatalysis, and many other areas. This short review aims to present the classification, some current mapping strategies, and advances of lead-free halide double perovskites, their derivatives, lead-free perovskitoid, and low-dimensional related crystals.

Tellurium(IV) Halide Achieving Effective Nonlinear-Optical Activity: The Role of Chiral Ligands and Lattice Distortion

Chiral organic-inorganic hybrid metal halides are a promising class of nonlinear-optical materials with unique optical properties and flexible crystal structures. However, the structures and properties of chiral hybrid tellurium halides, especially second harmonic generation (SHG), have not been reported. Here, by introducing chiral organic molecule (R/S)-methylbenzylammonium (R/S-MBA), we synthesized a pair of novel zero-dimensional (0D) chiral tellurium-based hybrid halides with noncentrosymmetric space group C2, (R/S-MBA)2TeCl6 (R/S-Cl). Single-crystal X-ray diffraction analysis and solid-state circular dichroism (CD) spectra confirm that R/S-Cl shows obvious enantiomer enrichment. Moreover, the resulting chiral products present an efficient SHG response. Interestingly, through manipulation of halogen atoms, two pairs of achiral tellurium halides, (R/S-MBA)2TeBr6 (R/S-Br) and (R/S-MBA)2TeI6 (R/S-I), were obtained, both of which crystallize in the centrosymmetric space group R3̅. It is noteworthy that R/S-I has a narrow band gap of 1.55 eV, which is smaller than that of most 0D metal halides and comparable to that of three-dimensional lead halide, showing its potential as a highly efficient light absorber.

Recent Advances and Opportunities of Eco-Friendly Ternary Copper Halides: A New Superstar in Optoelectronic Applications

Recently, the newly-emerging lead-free metal-halide materials with less toxicity and superior optoelectronic properties have received wide attention as the safer and potentially more robust alternatives to lead-based perovskite counterparts. Among them, ternary copper halides (TCHs) have become a vital group due to their unique features, including abundant structural diversity, ease of synthesis, unprecedented optoelectronic properties, high abundance, and low cost. Although the recent efforts in this field have made certain progresses, some scientific and technological issues still remain unresolved. Herein, a comprehensive and up-to-date overview of recent progress on the fundamental characteristics of TCH materials and their versatile applications is presented, which contains topics such as: i) crystal and electronic structure features and synthesis strategies; ii) mechanisms of self-trapped excitons, luminescence regulation, and environmental stability; and iii) their burgeoning optoelectronic devices of phosphor-converted white light-emitting diodes (WLEDs), electroluminescent LEDs, anti-counterfeiting, X-ray scintillators, photodetectors, sensors, and memristors. Finally, the current challenges together with future perspectives on the development of TCH materials and applications are also critically described, which is considered to be critical for accelerating the commercialization of these rapidly evolving technologies.

Tautomeric mixture coordination enables efficient lead-free perovskite LEDs

Lead halide perovskite light-emitting diodes (PeLEDs) have demonstrated remarkable optoelectronic performance1-3. However, there are potential toxicity issues with lead4,5 and removing lead from the best-performing PeLEDs-without compromising their high external quantum efficiencies-remains a challenge. Here we report a tautomeric-mixture-coordination-induced electron localization strategy to stabilize the lead-free tin perovskite TEA2SnI4 (TEAI is 2-thiopheneethylammonium iodide) by incorporating cyanuric acid. We demonstrate that a crucial function of the coordination is to amplify the electronic effects, even for those Sn atoms that aren't strongly bonded with cyanuric acid owing to the formation of hydrogen-bonded tautomeric dimer and trimer superstructures on the perovskite surface. This electron localization weakens adverse effects from Anderson localization and improves ordering in the crystal structure of TEA2SnI4. These factors result in a two-orders-of-magnitude reduction in the non-radiative recombination capture coefficient and an approximately twofold enhancement in the exciton binding energy. Our lead-free PeLED has an external quantum efficiency of up to 20.29%, representing a performance comparable to that of state-of-the-art lead-containing PeLEDs6-12. We anticipate that these findings will provide insights into the stabilization of Sn(II) perovskites and further the development of lead-free perovskite applications.

Unraveling Size-Dependent Ion-Migration for Stable Mixed-Halide Perovskite Light-Emitting Diodes

Mixed-halide perovskites show tunable emission wavelength across the visible-light range, with optimum control of the light color. However, color stability remains limited due to the notorious halide segregation under illumination or an electric field. Here, a versatile path toward high-quality mixed-halide perovskites with high emission properties and resistance to halide segregation is presented. Through systematic in and ex situ characterizations, key features for this advancement are proposed: a slowed and controllable crystallization process can promote achievement of halide homogeneity, which in turn ensures thermodynamic stability; meanwhile, downsizing perovskite nanoparticle to nanometer-scale dimensions can enhance their resistance to external stimuli, strengthening the phase stability. Leveraging this strategy, devices are developed based on CsPbCl1.5 Br1.5 perovskite that achieves a champion external quantum efficiency (EQE) of 9.8% at 464 nm, making it one of the most efficient deep-blue mixed-halide perovskite light-emitting diodes (PeLEDs) to date. Particularly, the device demonstrates excellent spectral stability, maintaining a constant emission profile and position for over 60 min of continuous operation. The versatility of this approach with CsPbBr1.5 I1.5 PeLEDs is further showcased, achieving an impressive EQE of 12.7% at 576 nm.

Enhanced Charge Balance for Efficient Electroluminescence from Cesium Copper Halides

Cesium copper halides have the advantages of high photoluminescence quantum efficiency and good stability, making them attractive for replacing toxic lead halides in the field of perovskite light-emitting diodes (LEDs). However, due to their shallow conduction band and the lack of electron transport layers compatible with it, it remains a great challenge to achieve charge balance in LED devices. This drawback manifests as the accumulation of holes at the interface between the emitting layer and electron transport layer, resulting in nonradiative recombination. Here, we demonstrate an effective approach to address this issue by suppressing hole injection, which is realized through modification of the poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) layer with polyethylenimine. This leads to cesium-copper-halide LEDs with a high external quantum efficiency of 5.6%, representing an advance in device architecture for efficient electroluminescence from cesium copper halides.

Advances in the Application of Perovskite Materials

Nowadays, the soar of photovoltaic performance of perovskite solar cells has set off a fever in the study of metal halide perovskite materials. The excellent optoelectronic properties and defect tolerance feature allow metal halide perovskite to be employed in a wide variety of applications. This article provides a holistic review over the current progress and future prospects of metal halide perovskite materials in representative promising applications, including traditional optoelectronic devices (solar cells, light-emitting diodes, photodetectors, lasers), and cutting-edge technologies in terms of neuromorphic devices (artificial synapses and memristors) and pressure-induced emission. This review highlights the fundamentals, the current progress and the remaining challenges for each application, aiming to provide a comprehensive overview of the development status and a navigation of future research for metal halide perovskite materials and devices.

Exceptional structural diversity of hybrid halocuprates(I) with methylammonium and formamidinium cations

Hybrid halocuprates(I) are nowadays the subject of intensive studies as promising materials for various optoelectronic applications. This class of materials is characterized by wide structural diversity enabled by a great variety in the size and shape of organic cations. Therefore, the study of composition-structure-property relationships is a key step for the rational design of new halocuprate materials with desired properties. In this paper, we comprehensively studied MABr/CuBr and FABr/CuBr systems (MA⁺ = methylammonium and FA⁺ = formamidinium) and established the existence of five novel phases (namely, MACu₂Br₃, FA₂[Cu₄Br₆], MACuBr₂, FACuBr₂, and FA₃CuBr₄) related to four different structural types and three distinct A⁺ : Cu⁺ stoichiometries (A⁺ = MA⁺/FA⁺). The optical properties of the discovered phases are studied by absorption and low-temperature photoluminescence spectroscopy. Based on a crystal-chemical analysis, we explained a unique structural diversity of the MA- and FA-based bromocuprates, as well as revealed new structure-property relationships.

Fluorescence Emission Is Highly Structure-Dependent in Hybrid Lead Halides

Hybrid lead halide perovskites have received extensive scientific attention owing to their great potential in the field of fluorescent displays and light-emitting diodes. Currently, most luminescent materials contain functional molecular and rare-earth metal ion parts. However, the mechanism of photoluminescence property in two-dimensional hybrid lead halide perovskites with different layered inorganic skeletons has been reported rarely. To better understand the effect of an inorganic skeleton on the fluorescence property, here, we report three organic-inorganic hybrid materials with different layered inorganic frameworks: (MACH)₂·PbBr₄ (Prv-1, MACH = cyclohexylmethylammonium), (2-MPQ)·PbBr₄ (Prv-2, 2-MPQ = 2-methylpiperazinium), and (TMBA)₄·Pb₃Br₁₀ (Prv-3, TMBA = N'N'N'-trimethylbenzylammonium). Among them, Prv-1 is a (100)-oriented perovskite, Prv-2 belongs to the (110)-oriented perovskite, and the inorganic framework of Prv-3 possesses [Pb₃Br₁₀] units. Interestingly, Prv-1 has a strong blue-violet fluorescence emission, while the luminescence effect of Prv-2 is very weak; notably, Prv-3 emits a charming bright-orange light. Meanwhile, results of theoretical computational studies also reveal that the electronic structure of all three compounds is highly dependent on structurally distorted [PbBr₆] octahedra, and the frontier molecular orbital (FMO) analysis further suggests that HOMO and LUMO of Prv-3 are contributed by inorganic and organic components, respectively. In addition, all three materials belong to direct band gap semiconductors, and the band gaps are 2.79, 2.97, and 2.76 eV, respectively. Significantly, there are obvious differences in conduction bands. Based on the above analysis, the photoluminescence mechanism of three hybrid materials is explained from the electronic levels. Consequentially, this work might provide practical strategies and perspectives for exploring novel structure-related properties.

Chirality in luminescent Cs3Cu2Br5 microcrystals produced via ligand-assisted reprecipitation

Herein we report new chiral luminescent Cs₃Cu₂Br₅ needle-like microcrystals and the analysis of their optical properties and the effect of the ligand structure on the transfer of chirality.

Stabilizing FASnI3-based perovskite light-emitting diodes with crystallization control

The toxicity of lead presents a critical challenge for the application of perovskite optoelectronics. Lead-free perovskite solar cells were achieved with formamidinium tin iodide (FASnI₃) perovskites, exhibiting decent power-conversion efficiencies (PCEs) of up to 14%, with >98% of the initial PCE retained after 3000 h of storage. However, when employed in light-emitting applications, FASnI₃-based perovskite LEDs (PeLEDs) show limited stability, with T₅₀ lifetimes of up to 0.25 h at 10 mA cm^-2. Here, we improve the stability of FASnI₃-based PeLEDs through the inclusion of a two-dimensional precursor phenethylamine iodide (PEAI), allowing controlled crystallization of the mixed-dimensional perovskite emitters. The density of defects is found to be reduced, accompanied by the suppression of oxidation from Sn²⁺ to Sn⁴⁺. Using an optimized perovskite composition, we achieve an EQE of 1.5% (a ∼10-fold improvement over the control devices), a maximum radiance of 145 W sr^-1 m^-2, and a record-long T₅₀ lifetime of 10.3 h at 100 mA cm^-2 for FASnI₃-based PeLEDs. Our results illuminate an alternative path toward lead-free PeLED applications.

One-Step Synthesis of White-Light-Emitting Carbon Dots for White LEDs with a High Color Rendering Index of 97

White-light-emitting carbon dots (WCDs) show innate advantages as phosphors in white light-emitting diodes (WLEDs). For WLEDs, the color rendering index (CRI) is the most important metric to evaluate its performance. Herein, WCDs are prepared by a facile one-step solvothermal reaction of trimellitic acid and o-phenylenediamine. It consists of four CDs identified by column chromatography as blue, green, yellow, red, and thus white light is a superposition of these four types of light. The mixture of the four CDs undergoes Förster resonance energy transfer to induce the generation of white light. The photoluminescence of WCDs originates from the synergistic effect of carbon core and surface states. Thereinto, the carbon core states dominate in RCDs, and the increase of amide contents and degree of conjugation promote the redshift of the emission spectra, which is further confirmed by theoretical calculations. In addition, a high CRI of 97 is achieved when the WCDs are used as phosphors to fabricate WLEDs, which is almost the highest value up to now. The multicolor LEDs can also be fabricated by using the four multicolor CDs as phosphors, respectively. This work provides a novel approach to explore the rapid preparation of low-cost, high-performance WCDs and CDs-based WLEDs.

Advances in electrically driven light-emitting diodes based on lead-free metal halides

The emerging lead halide perovskites show great potential for their use as emitters in electrically driven light-emitting diodes (LEDs) with external quantum efficiency (EQE) over 25%. While the toxicity of lead and inferior device stability are the main obstacles for their commercialization, replacing Pb²⁺ with low- or non-toxic metal ions to form low- or zero-dimensional structures provides an alternative approach to effectively tackle these issues. Recently, luminescent lead-free metal halides have been increasingly developed toward eco-friendly and highly efficient electroluminescence. In this feature article, we give a brief overview of recent advances in luminescent lead-free metal halides and their applications in electrically driven LEDs. The challenges and prospects in this field are outlined at the end.

Spectra stable deep-blue light-emitting diodes based on cryolite-like cerium(III) halides with nanosecond d-f emission

Next-generation wide color gamut displays require the development of efficient and toxic-free light-emitting materials meeting the crucial Rec. 2020 standard. With the rapid progress of green and red perovskite light-emitting diodes (PeLEDs), blue PeLEDs remain a central challenge because of the undesirable color coordinates and poor spectra stability. Here, we report Cs₃CeBr_xI_6-x (x = 0 to 6) with the cryolite-like structure and stable and tunable color coordinates from (0.17, 0.02) to (0.15, 0.04). Further encouraged by the short exciton lifetime (26.1 ns) and high photoluminescence quantum yield (~76%), we construct Cs₃CeBr_xI_6-x-based rare-earth LEDs via thermal evaporation. A seed layer strategy is conducted to improve the device's performance. The optimal Cs₃CeI₆ device achieves a maximum external quantum efficiency of 3.5% and a luminance of 470 cd m^-2 with stable deep-blue color coordinates of (0.15, 0.04). Our work opens another avenue to achieving efficient and spectrally stable deep-blue LEDs.

Efficient single-component white light emitting diodes enabled by lanthanide ions doped lead halide perovskites via controlling Förster energy transfer and specific defect clearance

Currently, a major challenge for metal-halide perovskite light emitting diodes (LEDs) is to achieve stable and efficient white light emission due to halide ion segregation. Herein, we report a promising method to fabricate white perovskite LEDs using lanthanide (Ln³⁺) ions doped CsPbCl₃ perovskite nanocrystals (PeNCs). First, K⁺ ions are doped into the lattice to tune the perovskite bandgap by partially substituting Cs⁺ ions, which are well matched to the transition energy of some Ln³⁺ ions from the ground state to the excited state, thereby greatly improving the Förster energy transfer efficiency from excitons to Ln³⁺ ions. Then, creatine phosphate (CP), a phospholipid widely found in organisms, serves as a tightly binding surface-capping multi-functional ligand which regulates the film formation and enhances the optical and electrical properties of PeNC film. Consequently, the Eu³⁺ doped PeNCs based-white LEDs show a peak luminance of 1678 cd m^-2 and a maximum external quantum efficiency (EQE) of 5.4%, demonstrating excellent performance among existing white PeNC LEDs from a single chip. Furthermore, the method of bandgap modulation and the defect passivation were generalized to other Ln³⁺ ions doped perovskite LEDs and successfully obtained improved electroluminescence (EL). This work demonstrates the comprehensive and universal strategies in the realization of highly efficient and stable white LEDs via single-component Ln³⁺ ions doped PeNCs, which provides an optimal solution for the development of low-cost and simple white perovskite LEDs.

Light Emission of Self-Trapped Excitons in Inorganic Metal Halides for Optoelectronic Applications

Self-trapped excitons (STEs) have recently attracted tremendous interest due to their broadband emission, high photoluminescence quantum yield, and self-absorption-free properties, which enable a large range of optoelectronic applications such as lighting, displays, radiation detection, and special sensors. Unlike free excitons, the formation of STEs requires strong coupling between excited state excitons and the soft lattice in low electronic dimensional materials. The chemical and structural diversity of metal halides provides an ideal platform for developing efficient STE emission materials. Herein, an overview of recent progress on STE emission materials for optoelectronic applications is presented. The relationships between the fundamental emission mechanisms, chemical compositions, and device performances are systematically reviewed. On this basis, currently existing challenges and possible development opportunities in this field are presented.

Organic-Inorganic Hybrid Cuprous-Based Metal Halides for Warm White Light-Emitting Diodes

Single-component emitters with stable and bright warm white-light emission are highly desirable for high-efficacy warm white light-emitting diodes (warm-WLEDs), however, materials with such luminescence properties are extremely rare. Low-dimensional lead (Pb) halide perovskites can achieve warm white photoluminescence (PL), yet they suffer from low stability and PL quantum yield (PLQY). While Pb-free air-stable perovskites such as Cs₂ AgInCl₆ emit desirable warm white light, sophisticated doping strategies are typically required to increase their PL intensity. Moreover, the use of rare metal-bearing compounds along with the typically required vacuum-based thin-film processing may greatly increase their production cost. Herein, organic-inorganic hybrid cuprous (Cu⁺ )-based metal halide MA₂ CuCl₃ (MA = CH₃ NH₃ ⁺ ) that meets the requirements of i) nontoxicity, ii) high PLQY, and iii) dopant-free is presented. Both single crystals and thin films of MA₂ CuCl₃ can be facilely prepared by a low-cost solution method, which demonstrate bright warm white-light emission with intrinsically high PLQYs of 90-97%. Prototype electroluminescence devices and down-conversion LEDs are fabricated with MA₂ CuCl₃ thin films and single crystals, respectively, which show bright luminescence with decent efficiencies and operational stability. These findings suggest that MA₂ CuCl₃ has a great potential for the single-component indoor lighting and display applications.

Vapor-Assisted In Situ Recrystallization for Efficient Tin-Based Perovskite Light-Emitting Diodes

Tin-based perovskites are a promising candidates to replace their toxic lead-based counterparts in optoelectronic applications, such as light-emitting diodes (LEDs). However, the development of tin perovskite LEDs is slow due to the challenge of obtaining high-quality tin perovskite films. Here, a vapor-assisted spin-coating method is developed to achieve high-quality tin perovskites and high-efficiency LEDs. It is revealed that solvent vapor can lead to in situ recrystallization of tin perovskites during the film-formation process, thus significantly improving the crystalline quality with reduced defects. An antioxidant additive is further introduced to suppress the oxidation of Sn²⁺ and increase the photoluminescence quantum efficiency up to ≈30%, which is an approximately fourfold enhancement in comparison with that of the control method. As a result, efficient tin perovskite LEDs are achieved with a peak external quantum efficiency of 5.3%, which is among the highest efficiency of lead-free perovskite LEDs.

Carbazole-Containing Polymer-Assisted Trap Passivation and Hole-Injection Promotion for Efficient and Stable CsCu2 I3 -Based Yellow LEDs

Perovskite light-emitting diodes (LEDs) are emerging light sources for next-generation lighting and display technologies; however, their development is greatly plagued by difficulty in achieving yellow electroluminescence, environmental instability, and lead toxicity. Copper halide CsCu₂ I₃ with intrinsic yellow emission emerges as a highly promising candidate for eco-friendly LEDs, but the electroluminescent performance is limited by defect-related nonradiative losses and inefficient charge transport/injection. To solve these issues, a hole-transporting poly(9-vinlycarbazole) (PVK)-incorporated engineering into CsCu₂ I₃ emitter is proposed. PVK with carbazole groups is permeated at the grain boundaries of CsCu₂ I₃ films by interacting with the uncoordinated Cu⁺ , reducing the Cu_Cs and Cu_I antisite defects to increase the radiative recombination and enhancing the hole mobility to balance the charge transport/injection, resulting in substantially enhanced device performances. Eventually, the yellow LEDs exhibit an 8.5-fold enhancement of external quantum efficiency, and the half-lifetime reaches 14.6 h, representing the most stable yellow LEDs based on perovskite systems reported so far.

Inorganic Chain Mediated Excitonic Properties in One-Dimensional Lead Halide Hybrid Perovskites

Semiconductors that emit intrinsic white light are considered next-generation lighting sources. Herein, the broadband emission of one-dimensional (1D) lead halide perovskites, TMAPbBr_3-xI_x (x = 0, 1, 1.5, 2, 3; TMA⁺ = tetramethylammonium), is systematically investigated. Lattice distortion causes the conversion of dark excitons to bright self-trapped excitons. Owing to its strongly localized exciton recombination and high absorption probability, TMAPbBr₃ is the most viable in this family. A delocalized hole increases the nonradiative recombination rate of excitons in TMAPbBr_3-xI_x alloys. In 1D TMAPbBr_3-xI_x perovskites, the vibration mode of the Pb-X bond stretching of the PbX₆ octahedra contributes more to the effect on exciton-phonon coupling than the mode of the X-Pb-X angle bending. Pb-X bond stretching and spontaneous polarization can tune exciton binding energy. This systematic study of excitonic behavior in 1D compounds relates the nature of ground states to the unknown excited states and provides the rational design of materials with stable and efficient broadband emission.

Efficient Near-Infrared Luminescence in Lanthanide-Doped Vacancy-Ordered Double Perovskite Cs2 ZrCl6 Phosphors via Te4+ Sensitization

All-inorganic lead-free perovskite-derivative metal halides have shown great promise in optoelectronics, however, it remains challenging to realize efficient near-infrared (NIR) luminescence in these materials. Herein, we report a novel strategy based on Te⁴⁺ /Ln³⁺ (Ln=Er, Nd, and Yb) co-doping to achieve efficient NIR luminescence in vacancy-ordered double perovskite Cs₂ ZrCl₆ phosphors, which are excitable by a low-cost near-ultraviolet light-emitting diode (LED) chip. Through sensitization by the spin-orbital allowed ¹ S₀ →³ P₁ transition of Te⁴⁺ , intense and multi-wavelength NIR luminescence originating from the 4f→4f transitions of Er³⁺ , Nd³⁺ , and Yb³⁺ was acquired, with a quantum yield of 6.1 % for the Er³⁺ emission. These findings provide a general approach to achieve efficient NIR emission in lead-free metal halides through ns² -metal and lanthanide ion co-doping, thereby opening up a new avenue for exploring NIR-emitting perovskite derivatives towards versatile applications such as NIR-LEDs and bioimaging.

Double-Network Hydrogel for Stretchable Triboelectric Nanogenerator and Integrated Electroluminescent Skin with Self-Powered Rapid Visual Sensing

Bio-inspired design plays a very significant role in adapting biological models to technical applications of flexible electronics. The flexible, stretchable, and portable electrode is one of the key technical challenges in the field. Inspired by the responses to mechanical stimuli of natural plants, we designed a highly transparent (over 95%), stretchable (over 1500%), and biocompatible electrode material by using polymerized double-network hydrogel for fabricating a triboelectric nanogenerator (SH-TENG). The SH-TENG can convert tiny mechanical stretching from human movements directly into electrical energy, and is capable of lighting up to 50 LEDs. Benefiting from bio-inspired design, the coplanar, non-overlapping electrode structure breaks through the limitations of conventional electrodes in wearable devices and overcomes the bottleneck of transparent materials. Furthermore, a self-powered raindrop visual sensing system was realized, which can perform quasi-real-time rainfall information monitoring and increase rainfall recognition ability of vehicle automatic driving systems. This study provides a novel strategy for making next-generation stretchable electronic devices and flexible visual sensing systems.

Top-Emitting Microcavity Light-Emitting Diodes Based on All-Thermally Evaporated Lead-Free Copper Halide Self-Trapped-Exciton Emitters

Lead-free metal halide light-emitting diodes (LEDs) based on cesium copper halide (CsCu₂I₃) self-trapped-exciton (STE) emissions show great potential in lighting and color display applications, especially because of their nontoxicity and earth abundance. However, so far, the efficiency and color purity of CsCu₂I₃-based LEDs remain low. Here we demonstrate the emission of a CsCu₂I₃ emitter can be enhanced and narrowed in a top-emitting microcavity device. Consequently, the CsCu₂I₃-based LED device with the assistance of a top-emitting microcavity has significantly narrowed and enhanced the emission spectrum with a full width at half-maximum of 59 nm and a maximum forward brightness of 14767 cd m^-2. To the best of our knowledge, this work achieves the narrowest CsCu₂I₃ LED spectra and demonstrates the potential of employing the microcavity effect to increase the efficiency and color purity of STE-based light-emitting devices.

In Situ Fabrication of Cs3Cu2I5: Tl Nanocrystal Films for High-Resolution and Ultrastable X-ray Imaging

Cs₃Cu₂I₅ nanocrystals (NCs) are considered to be promising materials due to their high photoluminescence efficiency and X-ray hardness. However, the present strategy depends on tedious fabrication with excessive chemical waste. The evasive iodide ion dissociation, inadaptable ligand system, low stability, and relatively low light yield severely impede their applications. Herein, we develop an in situ fabrication strategy for a flexible and large-area Tl-doped Cs₃Cu₂I₅ NC-polymer composite scintillation film with a high light yield (∼48800 photons/MeV) and improved stability. Tween 80 and phosphinic acid successfully inhibit the oxidation of iodide ions, and the films can be stored for at least six months. As a result, a high spatial resolution of 16.3 lp mm^-1 and a low detection limit of 305 nGy_air s^-1 were achieved. A radioluminescence intensity of >80% was maintained after a total irradiation dose of 604.8 Gy. These results indicate the promising application of these copper halide NCs in low-cost, flexible, and high-performance medical imaging.

Antimony -doped indium-based halide single crystals enabling white-light emission

Metal halides (TMPL)3InCl6·EtOH:xSb3+ with tunable colors were obtained by gradient Sb3+ doping. Interestingly, white emission was achieved when 0.1% of Sb3+ was employed, due to a combination of the cyan emission of organic moiety and orange emission from metal halides.

0D Perovskites: Unique Properties, Synthesis, and Their Applications

0D perovskites have gained much attention in recent years due to their fascinating properties derived from their peculiar structure with isolated metal halide octahedra or metal halide clusters. However, the systematic discussion on the crystal and electronic structure of 0D perovskites to further understand their photophysical characteristics and the comprehensive overview of 0D perovskites for their further applications are still lacking. In this review, the unique crystal and electronic structure of 0D perovskites and their diverse properties are comprehensively analyzed, including large bandgaps, high exciton binding energy, and largely Stokes-shifted broadband emissions from self-trapped excitons. Furthermore, the photoluminescence regulation are discussed. Then, the various synthetic methods for 0D perovskite single crystals, nanocrystals, and thin films are comprehensively summarized. Finally, the emerging applications of 0D perovskites to light-emitting diodes, solar cells, detectors, and some others are illustrated, and the outlook on future research in the field is also provided.

Perovskite White Light Emitting Diodes: Progress, Challenges, and Opportunities

As global warming, energy shortages, and environment pollution have intensified, low-carbon and energy-saving lighting technology has attracted great attention worldwide. Light emitting diodes (LEDs) have been around for decades and are considered to be the most ideal lighting technology currently due to their high luminescence efficiency (LE) and long lifespan. Besides, along with the development of modern technology, lighting technologies with higher performance and more functions are desired. Perovskite based LEDs (PeLEDs) have recently emerged as ideal candidates for lighting technology owing to the extraordinary photoelectric properties of perovskite, such as high photoluminescence quantum yields (PLQYs), easy wavelength tuning, and low-cost synthesis. Herein, we open this review by introducing the background of white LEDs (WLEDs), including their light-emitting mechanism, typical characteristics, and key indicators in applications. Then, four main approaches to fabricate WLEDs are discussed and compared. After that, in accordance with the four categories, we focus on the recent progress of white PeLEDs (Pe-WLEDs), followed by the challenges and opportunities for Pe-WLEDs in practical application. Meanwhile, some pertinent countermeasures to their challenges are put forward. Finally, the development promise of Pe-WLEDs is explored.

Highly Efficient Light-Emitting Diodes Based on an Organic Antimony(III) Halide Hybrid

As low-dimensional lead-free hybrids with higher stability and lower toxicity than those of three-dimensional lead perovskites, organic antimony(III) halides show great application potential in opt-electronic field owing to diverse topologies along with exceptional optical properties. We report herein an antimony(III) hybrid (MePPh₃ )₂ SbCl₅ with a zero-dimensional (0D) structure, which exhibits brilliant orange emission peaked at 593 nm with near-unity photoluminescent quantum yield (99.4 %). The characterization of photophysical properties demonstrates that the broadband emission with a microsecond lifetime (3.24 μs) arises from self-trapped emission (STE). Electrically driven organic light-emitting diodes (OLEDs) based on neat and doped films of (MePPh₃ )₂ SbCl₅ were fabricated. The doped devices show significant improvement in comparison to non-doped OLEDs. Owing to the much improved surface morphology and balanced carrier transport in light-emitting layers of doped devices, the peak luminance, current efficiency (CE) and external quantum efficiency (EQE) are boosted from 82 cd m^-2 to 3500 cd m^-2 , 1.1 cd A^-1 to 6.8 cd A^-1 , and 0.7 % to 3.1 % relative to non-doped devices, respectively.

Realizing White Emission of Single-Layer Dual-Color Perovskite Light-Emitting Devices by Modulating the Electroluminescence Emission Spectra

Dual-color emission in a single perovskite layer would make perovskite light-emitting devices (PLEDs) more competitive compared with other display technologies. However, due to the carrier dynamics in a blended perovskite film and the low reaction activation energy of the halide exchange reaction, it is very difficult to achieve the dual-color emission in a perovskite layer. Here, dual-color electroluminescence (EL) emission in a single perovskite layer has been realized by slowing the energy transfer from wide-bandgap energy levels to narrow-bandgap energy levels. Moreover, the EL spectra can be controlled by modulating the composition of the perovskite layer. When the amount of CH₃NH₃I(MAI) in the precursor was varied, white emission with CIE coordinates of (0.33, 0.34) could be achieved. Our work proposes a new strategy for white emission from PLEDs. Also, the analysis and discussion of carrier dynamics in this work may help to enhance our understanding of the working mechanism of PLEDs.

Research progress of full electroluminescent white light-emitting diodes based on a single emissive layer

Carbon neutrality, energy savings, and lighting costs and quality have always led to urgent demand for lighting technology innovation. White light-emitting diodes (WLEDs) based on a single emissive layer (SEL) fabricated by the solution method have been continuously researched in recent years; they are advantageous because they have a low cost and are ultrathin and flexible. Here, we reviewed the history and development of SEL-WLEDs over recent years to provide inspiration and promote their progress in lighting applications. We first introduced the emitters and analysed the advantages of these emitters in creating SEL-WLEDs and then reviewed some cases that involve the above emitters, which were formed via vacuum thermal evaporation or solution processes. Some notable developments that deserve attention are highlighted in this review due to their potential use in SEL-WLEDs, such as perovskite materials. Finally, we looked at future development trends of SEL-WLEDs and proposed potential research directions.

Highly Transparent, Dual-Color Emission, Heterophase Cs3Cu2I5/CsCu2I3 Nanolayer for Transparent Luminescent Solar Concentrators

Transparent luminescent solar concentrators (TLSCs) have been attracting wide attentions for their applications in transparent photovoltaic (PV) windows, smart greenhouses, and mobile electronics on account of the simple architecture and low-cost preparation. We report a novel strategy to fabricate TLSCs using the heterophase lead-free perovskites. The heterophase nanolayered films which combined CsCu₂I₃ and Cs₃Cu₂I₅ were prepared in one step using a dual-source coevaporation technique. The CsCu₂I₃/Cs₃Cu₂I₅ films exhibited UV light absorption, a high average visible transmission (AVT) of 86.70%, and dual-color white emission between 350 and 760 nm. Importantly, the TLSCs incorporated with the CsCu₂I₃/Cs₃Cu₂I₅ films exhibited an impressive optical conversion efficiency of 1.15% under keeping a high AVT of 86.70%. Meanwhile, the TLSCs incorporated with the heterophase films showed considerable stability under ambient conditions. The CIE 1960 color coordinates (0.2082, 0.4680) of the TLSCs incorporated with the CsCu₂I₃/Cs₃Cu₂I₅ films showed excellent aesthetic quality as compared with those of the TLSCs incorporated with lead-based perovskites. Our finding offers a strategy to prepare lead-free metal halides toward high-performance TLSCs and future transparent PV windows.