Fabrication of potato-like silver molybdate microstructures for photocatalytic degradation of chronic toxicity ciprofloxacin and highly selective electrochemical detection of H2O2

Potential application of zirconium molybdate as a novel catalyst for the selective dehydrogenation of methanol to anhydrous formaldehyde

The non-oxidative dehydrogenation of methanol is considered a promising method for producing formaldehyde (FA), where the resulting anhydrous formaldehyde is perfect for the use in the subsequent generation of oxygenated synthetic fuels. In the current investigation, a series of Zr(MoO4)2 nanoaggregates, as a novel solid acid catalyst, were hydrothermally fabricated at different temperatures in the presence of triethylamine (TEA) as a surfactant. The original and calcined catalysts were characterized by TGA, DSC, XRD, FT-IR, XPS, HR-TEM, acidity and nitrogen sorption. Analyses revealed that the addition of TEA to the preparation procedures significantly enhanced the textural, acidic, and the catalytic performance of these catalysts. Acidity measurements reflected that the surface of these catalysts possessed Brønsted type of acidic sites of weak and intermediate strength. Catalytic activity results demonstrated that, Zr(MoO4)2 catalyst with Zr: TEA molar ratio of 1:1 (Z1T1) annealed at 400°C exhibited the maximum methanol conversion of 99% and 95% selectivity to formaldehyde at reaction temperature of 325°C. The remarkable catalytic performance was well correlated to the variation in acidity of the catalyst. This catalyst offered a long-term stability towards the production of formaldehyde for a period of time of 160 h with the same activity and selectivity. Also, this catalyst could be re-used for five time giving almost the same performance. The reason for this extreme catalytic activity and selectivity towards formaldehyde synthesis is the presence of weak and moderate strengthened Brønsted acid sites. In light of this, this work has produced an active, stable, and selective catalyst for the conversion of methanol to formaldehyde that is competitive with the most effective conventional and recently discovered catalysts.

An ultrasensitive ECL immunosensor with a dual signal amplification strategy using AuNPs@GO@SmMoSe2 and Gd2(MoO4)3 for estriol detection

BACKGROUND

Estriol (E3) is a common estrogen responsible for regulating the female reproductive system, but excessive amount can pose health risks to humans and wild life. Therefore, sensitive and accurate detection of estriol level is crucial. A novel competitive ECL immunosensor based on a dual signal amplification strategy of AuNPs@GO@SmMoSe2 and Gd2(MoO4)3 was fabricated for ultrasensitive detection of estriol. Graphene oxide (GO) increased the electric conductivity and surface area of SmMoSe2 and gold nanoparticles (AuNPs) improved the electrochemical active sites of GO@SmMoSe2. In order to further amplify the ECL signals, Gd2(MoO4)3 with excellent electron transfer capability were used for binding E3-antigen (Ag). Then, Gd2(MoO4)3-Ag/BSA competed with Standard E3 for limited number of antibodies to construct a competitive ECL immunosensor.

RESULTS

Under optimized condition, the proposed competitive ECL immunosensor was used to detect various concentrations of Standard E3 samples. In addition, the proposed ECL immunosensor showed the high sensitivity for E3 detection in range between 0.001 and 500 ng/mL with the detection limit of 0.0073 ng/mL (S/N = 3). The wider linear range and lower detection limits of the proposed ECL immunosensor might be attributed to outstanding ECL properties of AuNPs@GO@SmMoSe2 and Gd2(MoO4)3 nanosheets. Furthermore, the proposed competitive ECL immunosensor was also compared with various detection methods. Based on above, the fabricated ECL immunosensor was employed for real sample analysis with acceptable RSD values and recoveries.

SIGNIFICANCE

A dual signal amplification strategy enhanced the potential of the well-prepared ECL immunosensor for detecting E3 samples in the real environment. Thereby, the successfully fabricated competitive ECL immunosensor with excellent electrochemical properties, long term storage stability, and high sensitivity and selectivity validated its potential application for environmental monitoring and analysis.

Defect state enhanced nonlinear absorption and optical limiting behaviour of erbium doped silver molybdate nanostructures

Transition metal based optical limiting materials have garnered significant attention due their crucial role in protecting sensitive optical system from high intense laser damage. Transition metal molybdates exhibits nonlinear optical (NLO) response, which attenuate highly intense light by transmitting light of desired intensity. Herein we report Silver molybdate (Ag2MoO4) nanostructures doped with erbium (Er) ions were successfully synthesized by simple co-precipitation technique. The proper incorporation of Er ions into the Ag2MoO4 lattice without altering the crystal structure was confirmed by XRD Analysis. The optical properties studied using UV-Vis absorption Spectroscopy exhibited maximum absorption in UV region and the absorption in the visible region is found to increase with the addition of Er ions into the host lattice. The XPS spectra confirmed the + 3 oxidation state of erbium and Ag0 state of silver. The NLO parameters such as, nonlinear absorption (NLA) and optical limiting (OL) was studied for the first time under 532 nm nanosecond laser excitation. Results suggest that erbium doped silver molybdate exhibited reverse saturable absorption originated from two photon absorption. The synthesized samples exhibited excellent nonlinear absorption and optical limiting performance. Also it is observed that with the addition of Er ions, the two photon absorption (2PA) is found to enhance from 0.85 × 10-10 m/W (pure Ag2MoO4) to 6.223 × 10-10 m/W for 0.5% Er doped sample. So, erbium doped silver molybdate nanostructures can be used for various tunable optoelectronic devices.

Disposable electrochemical sensors based on reduced graphene oxide/polyaniline/poly(alizarin red S)-modified integrated carbon electrodes for the detection of ciprofloxacin in milk

An electrochemical sensor based on an electroactive nanocomposite was designed for the first time consisting of electrochemically reduced graphene oxide (ERGO), polyaniline (PANI), and poly(alizarin red S) (PARS) for ciprofloxacin (CIPF) detection. The ERGO/PANI/PARS-modified screen-printed carbon electrode (SPCE) was constructed through a three-step electrochemical protocol and characterized using FTIR, UV-visible spectroscopy, FESEM, CV, LSV, and EIS. The new electrochemical CIPF sensor demonstrated a low detection limit of 0.0021 μM, a broad linear range of 0.01 to 69.8 μM, a high sensitivity of 5.09 μA/μM/cm2, and reasonable selectivity and reproducibility. Moreover, the ERGO/PANI/PARS/SPCE was successfully utilized to determine CIPF in milk with good recoveries and relative standard deviation (< 5%), which were close to those with HPLC analysis.

Light-driven photocatalysis as an effective tool for degradation of antibiotics

Antibiotic contamination has become a severe issue and a dangerous concern to the environment because of large release of antibiotic effluent into terrestrial and aquatic ecosystems. To try and solve these issues, a plethora of research on antibiotic withdrawal has been carried out. Recently photocatalysis has received tremendous attention due to its ability to remove antibiotics from aqueous solutions in a cost-effective and environmentally friendly manner with few drawbacks compared to traditional photocatalysts. Considerable attention has been focused on developing advanced visible light-driven photocatalysts in order to address these problems. This review provides an overview of recent developments in the field of photocatalytic degradation of antibiotics, including the doping of metals and non-metals into ultraviolet light-driven photocatalysts, the formation of new semiconductor photocatalysts, the advancement of heterojunction photocatalysts, and the building of surface plasmon resonance-enhanced photocatalytic systems.

Silver molybdate: an excellent optical limiting material under nanoregime for photonic device application

There is a mounting demand for nonlinear optical materials with superior optical limiting performance which has a noticeable impact on protecting the delicate optical components from laser-induced damage. Transition metal molybdates have garnered attention in the nonlinear optics field due to their outstanding optical and luminescent properties, which give rise to widespread applications in next-generation optoelectronics devices. The structural confirmation of the as prepared silver molybdate nanoparticles were made by XRD and Raman spectroscopy analysis. The linear optical properties and the band gap of the synthesized material were studied using UV-Visible and photoluminescence spectroscopy. SEM analysis revealed the pebble like morphology of the silver molybdate nanostructures. The nonlinear responses of the samples were studied using open aperture z-scan approach with Nd:YAG pulsed laser (532 nm, 9 ns, 10 Hz). The sample exhibits reverse saturable absorption pattern attributed to the two photon absorption (2PA) mechanism. The obtained OL threshold value is in the order of 1012 which is suitable for fabricating optical limiters in nano second pulsed laser regime.

Fabrication of UiO-66/GCN, a Hybrid Photocatalyst, for Effective Degradation of Ciprofloxacin, Toxicity Estimation, and Its Antibacterial Activity

Fabrication of a metal-organic framework-based photocatalyst has been gaining much interest due to its higher surface area and reasonable band gap, enhancing its photocatalytic activity. This study attempted a facile synthesis of the hybrid photocatalyst UiO-66 doped with graphitic carbon nitride (GCN) by a simple solvothermal method. This composite minimized the drawback related to photogenerated charge transfer and recombination and helped the absorption of visible light. The material was investigated by using various instrumental techniques. In this work, ciprofloxacin (CIP), a fluoroquinolone drug, was chosen as a target micropollutant, and a photodegradation experiment was carried out by using UiO-66, GCN, and UiO-66/GCN under a visible light source, which exhibited 81.85, 69.48, and 93.60% of degradation, respectively. Finally, liquid chromatography mass spectrometry analysis and theoretical computation were carried out to identify the CIP degradation mechanism, and T.E.S.T. software was used to investigate the toxicity of the intermediate products. Apart from photocatalytic activity, the prepared material was also tested for its antibacterial properties against Staphylococcus aureus and Escherichia coli.

Tracking of structural defects induced by Eu-doping in β-Ag2MoO4: their influences on electrical properties

In this study, several methods were employed to investigate the electrical characteristics of β-Ag2MoO4 systems, both Eu-doped and undoped, synthesized using the microwave-assisted hydrothermal method. The focus extended to understanding how synthesis time influences material defects, with doping fixed at 1%. A systematic shift in the silver vacancy (VAg) concentration was observed within the doped β-Ag2MoO4 system. Specifically, this study demonstrated that the incorporation of Eu3+ into polycrystalline β-Ag2MoO4 initially increases the VAg concentration. However, as the synthesis time progresses, the VAg concentration decreases, resulting in alterations in the resulting electrical properties, arising from the intricate interplay between the number of grain boundaries and carrier density. By combining information obtained from photoluminescence, positron annihilation lifetime spectroscopy, and impedance spectroscopy, a comprehensive conduction mechanism was formulated, shedding light on both doped and undoped β-Ag2MoO4 systems.

Novel electrospun bead-like Ag2MoO4 nanofibers coated on Ni foam for visible light-driven heterogeneous photocatalysis and high-performance supercapacitor electrodes

Novel Ag2MoO4 nanocomposite fibers were designed to enhance the photocatalytic response and supercapacitor performance of MoO3 grown via the sol-gel electrospinning technique. The Ag2MoO4 nanocomposite fibers exhibit a high specific surface area of 49.3 m2 g-1 comprising nanobeads that aggregate in the fibrous structure. The photodegradation efficiency of Ag2MoO4 was evaluated as 62% under visible light irradiation which improved to 71% with heterogeneous photocatalysis. The Ag2MoO4@Ni foam exhibited a low Rct of 19.6 Ω, and an enhanced specific capacitance of 1445 F g-1 was obtained at 1 A g-1, with 93% of its initial capacitance remaining after 5000 cycles. In addition, the Ag2MoO4//activated carbon asymmetric supercapacitor possesses an excellent energy density of 76.6 W h kg-1 at 743.2 W kg-1 and a noteworthy cycling durability of 91% after 5000 cycles. Our findings demonstrate that the electrospun Ag2MoO4@Ni foam is an important and inexpensive electrode material for supercapacitor applications and visible light-driven heterogeneous photocatalysis, drawing on the synergic effects of Ag and Mo to exhibit much better performance.

Intimate coupling of gC3N4/CdS semiconductor on eco-friendly biocarrier loofah sponge for enhanced detoxification of ciprofloxacin

Ciprofloxacin is one of the antibiotics predominantly used to treat bacterial infections, however excess usage, and release of antibiotic from various sources to the environment can cause severe risks to human health since it was considered as emerging pollutant. This study deals with the intimately coupled photocatalysis and biodegradation (ICPB) of ciprofloxacin using gC3N4/CdS photocatalytic semiconductor and eco-friendly renewable loofah sponge as biocarrier in the ICPB. The photocatalyst gC3N4/CdS was prepared and their synergistic photocatalytic degradation of ciprofloxacin were assessed and the results shows that gC3N4/CdS (20%) exhibit 79% degradation efficiency in 36 h. Further ICPB exhibited enhanced ciprofloxacin degradation 95% at 36 h. The 62.4% and 81.1% of chemical oxygen demand (COD) removal was obtained in the photocatalysis and ICPB respectively. Enhanced degradation of ciprofloxacin and COD removal was due to the synergetic photoelectrons generated from the gC3N4/CdS (20%) transferred to the bacterial communities which intensely mineralize the degradation products produced from the photocatalysis process. Furthermore, production of hydroxyl •OH and superoxide radical anion O2• were identified actively involved in the degradation of ciprofloxacin. The biocarrier loofah sponge provided favourable environment to the bacterial communities for the formation of biofilm and production of extracellular polymeric substances (EPS). Excess quantity of EPS production in the ICPB helps in the prevention of toxicity of photocatalyst to bacterial communities as well as facilitate the extracellular electron transfer process. This work provides a novel path for enhanced degradation of ciprofloxacin using eco-friendly, low cost and renewable biocarrier loofah sponge in the ICPB system.

Facile engineering of gadolinium cobaltite anchored on functionalized carbon black as dynamic electrocatalyst for ultra-sensitive detection of nitroaromatic drug

There has been a significant increase in the production and use of antibiotic drugs. However, the overuse and improper disposal of nitro-based antibiotics pose a significant threat to human health and the ecosystem. Specifically, the residues of antibiotic drugs such as nitrofurantoin (NFT) are dangerous to public health and pose a threat to the environment. In this study, we prepared a novel nanocomposite consisting of gadolinium cobaltite embedded functionalized carbon black (GdCoO3/f-CB) via a simple hydrothermal technique and utilized this nanocomposite as an electrode material for the electrochemical detection of NFT. The structural and morphological properties of the GdCoO3/f-CB nanocomposite was analyzed using a range of techniques, including XRD, Raman, XPS, EDX-Mapping, and HR-TEM. The electrocatalytic activity of the GdCoO3/f-CB nanocomposite was investigated using both CV and DPV techniques for the detection of NFT. Our results demonstrated that the prepared GdCoO3/f-CB nanocomposite delivered the excellent activities toward the detection of NFT at an extremely low limit of detection (LOD) of 2 nM and exhibited high sensitivity of 31 μA·μM-1·cm-2. Additionally, the proposed NFT sensor using GdCoO3/f-CB nanocomposite provided excellent reproducibility, repeatability, and selectivity, even in the presence of interfering molecules such as metal ions, biomolecules, and similar nitro compounds. These findings suggest that the GdCoO3/f-CB nanocomposite provides significant potential for the electrochemical detection of antibiotic drug residues for public health and the environment.

Ag2Mo3O10·2H2O nanorods under high pressure: In situ Raman spectroscopy

This work presents a pressure-dependent behavior of silver trimolybdate dihydrate (Ag₂Mo₃O₁₀·2H₂O) nanorods using in situ Raman scattering. The Ag₂Mo₃O₁₀·2H₂O nanorods were obtained by the hydrothermal method at 140 °C for 6 h. The structural and morphological characterization of the sample was performed by powder X-ray diffraction (XRD) and scanning electron microscopy (SEM). Pressure-dependent Raman scattering studies were performed on Ag₂Mo₃O₁₀·2H₂O nanorods up to 5.0 GPa using a membrane diamond-anvil cell (MDAC). The vibrational spectra under high pressure showed splitting and emergence of new bands above 0.5 GPa and 2.9 GPa. Reversible phase transformations under pressure were observed in silver trimolybdate dihydrate nanorods: Phase I - ambient phase (1 atm - 0.5 GPa) → Phase II (0.8 GPa - 2.9 GPa) → Phase III (above 3.4 GPa).

Amoxicillin degradation by iron photonanocatalyst synthetized by green route using pumpkin (Tetsukabuto) peel extract

Amoxicillin is a pharmaceutical compound that is not degraded in wastewater treatment plants, causing harm to the environment. In this work, an iron nanoparticle (IPP) was synthesized using pumpkin (Tetsukabuto) peel extract for the degradation of amoxicillin under UV light. The IPP was characterized using scanning electron microscopy/energy dispersive x-ray spectroscopy, transmission electron microscopy, X-ray diffraction, Fourier-transform infrared spectroscopy, thermogravimetric analysis, and Raman spectroscopy techniques. The photocatalytic efficiency of IPP was analyzed by investigating the effect of IPP dosage (1-3 g L^-1), initial amoxicillin concentration (10-40 mg L^-1), pH (3-9), reaction time (10-60 min), and the effect of inorganic ions (1 g L^-1). The optimum conditions for the maximum photodegradation removal (≈60%) were IPP = 2.5 g L^-1, initial amoxicillin concentration = 10 mg L^-1, pH = 5.6, and irradiation time = 60 min. The results of this study showed that inorganic ions (Mg²⁺, Zn²⁺, and Ca²⁺) negatively affect the photodegradation of amoxicillin by IPP; the quenching test showed that hydroxyl radical (OH^•) is the primary reactive species of the reaction; NMR analysis revealed changes in amoxicillin molecules after photoreaction; the subproducts of photodegradation were identified by LC-MS; the proposed kinetic model demonstrated good applicability, predicting the behavior of OH^• and determining the kinetic constant, and the cost analysis based on required energy (238.5 kWh m^-3 order^-1) indicated that the amoxicillin degradation method by IPP is economically viable. This study developed a new efficient iron nanocatalyst for the removal of antibiotics from aqueous environments and provided optimal conditions and relevant information in the area of advanced oxidative processes.

Design and synthesis of nickel-doped cobalt molybdate microrods: An effective electrocatalyst for the determination of antibiotic drug ronidazole

Ronidazole (RDZ) is a veterinary antibiotic drug that has been used in animal husbandry as feed. However, improper disposal and illegal use of pharmaceuticals have severely polluted water resources. Doping/substitution of metal ions is an effective strategy to change the material's crystal phase, morphology, and electrocatalytic activity. In this work, nickel (Ni²⁺)-doped cobalt molybdate microrods (NCMO MRs) were prepared for the electrochemical detection of RDZ. The catalyst was prepared by reflux method followed by calcination at 500 °C. The prepared catalyst was confirmed by various spectroscopic and microscopic analyses. XRD and Raman spectroscopy demonstrated that the phase transition from β-CoMoO₄ to α-CoMoO₄ was achieved by Ni²⁺ doping. The SEM analysis showed that cobalt molybdate (CMO) microrods were self-assembled during Ni²⁺ doping and formed an urchin-like structure, and the average diameter of the MRs was ±50 nm. The electrocatalytic activity of the catalysts was analyzed using the CV technique. The NCMO MRs/GCE exhibited the higher current response than the pristine CMO. The electron transfer coefficient (α = 0.56) and heterogeneous rate constant (ks = 0.32 s^-1) of NCMO MRs/GCE were evaluated by kinetic studies. In addition, the diffusion coefficient of RDZ was determined to be 2.32 × 10^-5 cm²/s. Moreover, NCMO MRs/GCE exhibits a low detection limit for RDZ (15 nM) as well as a higher sensitivity (1.57 μA μM^-1 cm^-2). The fabricated RDZ sensor was successfully applied to analysis of lake and tap water samples. Based on the results, we believe that the as-prepared NCMO MRs/GCE is a viable electrode material for RDZ sensors in environmental monitoring.

Silver Trimolybdate (Ag2Mo3O10.2H2O) Nanorods: Synthesis, Characterization, and Photo-Induced Antibacterial Activity under Visible-Light Irradiation

The present study reports the synthesis, characterization, and antibacterial properties of silver trimolybdate (Ag2Mo3O10.2H2O) nanorods. The synthesis was performed using a conventional hydrothermal method. The sample was characterised by scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, UV-Vis-NIR diffuse reflectance, thermogravimetric analysis (TGA), and differential scanning calorimeter (DSC). The direct antibacterial activity was evaluated using the microdilution method to determine the minimum inhibitory concentration (MIC). To assess the ability of Ag2Mo3O10.2H2O nanorods to modulate antibacterial resistance, the MIC of aminoglycosides was established in the presence of a subinhibitory concentration of this substance alone and associated with LED light exposure. The characterization of the sample indicated that the synthesis of silver trimolybdate generated nanometric crystals with rod-like morphology, without secondary phases. The treatment with Ag2Mo3O10.2H2O nanorods alone or combined with visible LED lights exhibited clinically relevant antibacterial activity against both Gram-negative and Gram-positive bacteria. This nanostructure presented a variable antibiotic-modulating action, which was not improved by visible LED light exposure. Nevertheless, LED lights showed promising antibiotic-enhancing activities in the absence of Ag2Mo3O10.2H2O nanorods. In conclusion, silver trimolybdate dihydrate nanorods have antibacterial properties that can be photocatalysed by visible-light exposure. While showing the potential use to combat antibacterial resistance, the simultaneous combination of silver trimolybdate, visible LED lights, and antibacterial drugs should be carefully analysed to avoid antagonist effects that could impair the effectiveness of antibiotic therapy.

Phytochemically stabilized chitosan encapsulated Cu and Ag nanocomposites to remove cefuroxime axetil and pathogens from the environment

Antibiotics have been a source of concern since they are causing resistance in bacteria that live in water and air. As a result, green technology was used to manufacture silver and copper nanoparticles, which were encapsulated with the biopolymer chitosan derived from the root extract of the Potentilla astrosanguinea plant. XRD, FTIR, TEM, EDX, and UV-Visible spectroscopy were methods used for structural and spectroscopic analysis. These nanomaterials have a roughly spherical 2-30 nm average size and a face-centered cubic (FCC) shape, according to the findings. The photocatalytic drug degradation and antibacterial properties of the produced nanocomposites were outstanding, with some resistance lasting longer than 180 days. The current study discovered that under UV light exposure, silver nanocomposites degrade drugs rapidly within 40 min, with an average rate of over 95%, while copper nanocomposites degrade drugs rapidly within 70 min, with an average rate of 84%. These nanocomposites have demonstrated exceptionally compelling antibacterial action against Gram-positive, Gram-negative, and fungal pathogens in addition to photocatalytic activity. The lowest recorded MIC values were 10.30 μg/mL and 10.84 μg/mL, respectively, whereas the lowest MBC values were 91.24 μg/mL and 99.50 μg/mL.

Electrochemical (Bio)Sensors for the Detection of Organophosphorus Pesticides Based on Nanomaterial-Modified Electrodes: A Review

Organophosphorus pesticides were easily remained in fruits and vegetables which would be harm to the environmental safety and human health. In recent years, due to the simple preparation process, fast response and high sensitivity, the electrochemical (bio)sensors have received increasing attention, which were extensively used as the sensing platform for the detection of OPPs. The mechanisms for the determination of OPPs mainly included redox of nitrophenyl OPPs, enzyme hydrolysis and inhibition, immunosensor, aptasensor. Nowadays, the mainly explored electrode material has focused on metal-organic frameworks, metal and metal derivatives, carbon materials (carbon nanotube, graphene, g-C3N4), MXene, etc. These nanomaterials played important roles in the electrochemical (bio)sensors, which included: (a) as an electrocatalyst to promote the redox reaction, (b) as a carrier to load the enzyme or aptamer, (c) as a recognizer to identify the targets. The nanomaterials-based electrochemical (bio)sensor was a rapid, cost-effective methods to detect OPPs with high sensitivity. Besides, this review compared the analytical performance of different nanomaterials-based electrochemical (bio)sensors, and also identified the key challenges in the future. It would provide new ideas and insights to the further development and application of electrochemical (bio)sensors and the detection of pesticides in real samples.

Rietveld Refinement, Morphology, and Optical and Photoluminescence Properties of a β-Ag1.94Cu0.06MoO4 Solid Solution

Corner-truncated cubic β-Ag_1.94Cu_0.06MoO₄ microcrystals were synthesized using the hydrothermal method. These were investigated by X-ray diffraction, confirming obtention of the spinel structure Fd3̅m. Through Raman spectroscopy are confirmed all modes for the point group of O_h⁷. The E_gap shows a decrease of the band gap from 3.20 to 3.07 eV, with reduction of the conduction band occurring from -0.20 eV (β-Ag₂MoO₄) to -0.13 eV (β-Ag_1.94Cu_0.06MoO₄), suggesting a p-type behavior for the Cu²⁺ ion. The field-emission scanning electron microscopy images confirm the morphological changes for β-Ag₂MoO₄, where potato-like microcrystals were found. Meanwhile, corner-truncated cubic microcrystals for β-Ag_1.94Cu_0.06MoO₄. The photoluminescence (PL) spectrum confirms the increase in the PL emission for β-Ag_1.94Cu_0.06MoO₄, with suppression of the deep defects occurring in the structure caused by oxygen and silver atoms. In contrast, the green region is intensified because of distortions of the Ag-O and Mo-O bonds. Therefore, the β-Ag_1.94Cu_0.06MoO₄ solid solution has PL emission with CCT (4510 K) and CIE coordinates (x = 0.372 and y = 0.433), which could be interesting properties for applications as light-emitting diodes.

Pico-molar electrochemical detection of ciprofloxacin at composite electrodes

Rapid determination of ciprofloxacin at OCNTs-PDA-Ag sensors enables environmental monitoring and future bioelectrochemical studies.

Ag/α-Ag2MoO4/h-MoO3 nanoparticle based microspheres: synthesis and photosensitive properties

We report a new and the most simple strategy for the synthesis of silver molybdate functional composite microspheres based on low molecular weight gelators -amino acids, silver salts and heptamolybdate ions. The resulting material shows a high photocatalytic activity with respect to the methylene blue dye degradation at neutral pH.

Synergetic effect of Sn doped ZnO nanoparticles synthesized via ultrasonication technique and its photocatalytic and antibacterial activity

The current work reports the photocatalytic and antibacterial performance of tin (Sn) doped zinc oxide (ZnO) nanoparticles synthesized via ultrasonic aided co-precipitation technique. The increase of Sn concentration decreased the lattice parameter and increased the crystallite size without changing the ZnO structure. The hexagonal shaped particles and sheets obtained for 3% and 5% Sn substituted ZnO, respectively. The increase of dopant concentration reduced the reflectance and optical band gap energy of Sn doped ZnO. The vibrational band present at 1443 cm^-1 confirmed the successful bond formation of Sn-O-Zn. The 5% Sn doped ZnO nanoparticles exhibited greater dye elimination rate of methylene blue compared to 3% Sn. The antibacterial activity of Sn doped ZnO showed the higher zone of inhibition about 14 mm against different pathogens. The 5% Sn doped ZnO photocatalyst improve the transfer rate of photo excite carrier and decrease the rate of recombination which greatly influence on the photocatalytic and antibacterial performance.

Plastic optical fibres applied on the photocatalytic degradation of phenol with Ag2MoO4 and ß-Ag2MoO4/Ag3PO4 under visible light

In this study, plastic optical fibre (POF) was considered as a light-transmitting medium and substrate for use in a photocatalytic environmental purification system, using Ag₂MoO₄ and β-Ag₂MoO₄/Ag₃PO₄ as photocatalysts. Pure Ag₂MoO₄ and a β-Ag₂MoO₄/Ag₃PO₄ composite were synthesized using a facile precipitation method. The composition, structures and optical properties of as-prepared catalysts were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), field-emission scanning electron microscopy (FESEM), UV/Vis diffuse reflectance spectroscopy (UV/Vis DRS), BET surface area and TGA/DTG. The catalysts were immobilized on POF and on the glass reactor surface and their efficiency in the phenol degradation was evaluated in a batch reactor under visible light. The use of POF offers advantages such as ease of handling and good adherence characteristics to support Ag₂MoO_4. The photoactivity follows the order β-Ag₂MoO₄/Ag₃PO₄ ≅ Ag₂MoO₄> TiO₂ P25, for photocatalysts immobilized on the glass reactor surface or in aqueous suspension. The immobilization of Ag₂MoO₄ on POF revealed that thinner Ag₂MoO₄ coatings achieved faster pollutant removal rates from solution, and the optimal catalyst deposition is 0.64 mg/cm², causing maximum the light penetration and electron-hole generation close to the solid-liquid interface.

Ultrasonication-aided synthesis of nanoplates-like iron molybdate: Fabricated over glassy carbon electrode as an modified electrode for the selective determination of first generation antihistamine drug promethazine hydrochloride

The innovation of novel and proficient nanostructured materials for the precise level determination of pharmaceuticals in biological fluids is quite crucial to the researchers. With this in mind, we synthesized iron molybdate nanoplates (Fe₂(MoO₄)₃; FeMo NPs) via simple ultrasonic-assisted technique (70 kHz with a power of 100 W). The FeMo NPs were used as the efficient electrocatalyst for electrochemical oxidation of first-generation antihistamine drug- Promethazine hydrochloride (PMH). The as-synthesized FeMo NPs were characterized and confirmed by various characterization techniques such as XRD, Raman, FT-IR, FE-SEM, EDX and Elemental mapping analysis and electron impedance spectroscopy (EIS). In addition, the electrochemical characteristic features of FeMo NPs were scrutinized by electrochemical techniques like cyclic voltammetry (CV) and differential pulse voltammetry technique (DPV). Interestingly, the developed FeMo NPs modified glassy carbon electrode (FeMo NPs/GCE) discloses higher peak current with lesser anodic potential on comparing to bare GCE including wider linear range (0.01-68.65 µM), lower detection limit (0.01 µM) and greater sensitivity (0.97 µAµM^-1cm^-2). Moreover, the as-synthesized FeMo NPs applied for selectivity, reproducibility, repeatability and storage ability to investigate the practical viability. In the presence of interfering species like cationic, anionic and biological samples, the oxidation peak current response doesn't cause any variation results disclose good selectivity towards the detection of PMH. Additionally, the practical feasibility of the FeMo NPs/GCE was tested by real samples like, commercial tablet (Phenergan 25 mg Tablets) and lake water samples which give satisfactory recovery results. All the above consequences made clear that the proposed sensor FeMo NPs/GCE exhibits excellent electrochemical behavior for electrochemical determination towards oxidation of antihistamine drug PMH.

Synthesis, characterization and catalytic performance of nanostructured dysprosium molybdate catalyst for selective biomolecule detection in biological and pharmaceutical samples

The current study reports a new, simple and fast method using a flake-like dysprosium molybdate (Dy2MoO6; FL-DyM) nanostructured material to detect the antibiotic drug metronidazole (METZ). This nanocomposite material was employed on the surface of a glassy carbon electrode (GCE) to develop the electrode (FL-DyM/GCE). Further, the synthesized FL-DyM was systematically characterized by powder X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy-dispersive X-ray diffraction (EDS), elemental mapping, X-ray photoelectron spectroscopy (XPS), and Brunauer-Emmett-Teller (BET) analyses. Cyclic (CV) and differential pulse voltammetry (DPV) techniques were used to study the electrochemical properties. The FL-DyM/GCE-based sensor demonstrated excellent selectivity and sensitivity for the detection of the drug METZ, which could be attributed to the strong affinity of FL-DyM towards the -NO2 group in METZ, and the good electrocatalytic activity and conductivity of FL-DyM. The fabrication and optimization of the working electrode were accomplished with CV and DPV obtained by scan rate and pH studies. Compared to the bare GCE and other rare-earth metal molybdates, the FL-DyM/GCE sensor displayed a superior electrocatalytic activity response for METZ detection. The sensor demonstrated a good linear relationship over the concentration range of 0.01-2363 μM. The quantification and detection limits were found to be 0.010 μM and 0.0030 μM, respectively. The FL-DyM/GCE sensor displayed excellent selectivity, repeatability, reproducibility, and stability for the detection of METZ in human urine and commercial METZ tablet samples, which validates the new technique for efficient drug sensing in practical applications.

Iron Magnetic Nanoparticle-Induced ROS Generation from Catechol-Containing Microgel for Environmental and Biomedical Applications

Reactive oxygen species (ROS) can degrade organic compounds and function as a broad-spectrum disinfectant. Here, dopamine methacrylamide (DMA) was used to prepare catechol-containing microgels, which can release ROS via metal-catechol interaction. A combination of the microgel and iron magnetic nanoparticle (FeMNP) significantly reduced the concentration of four organic dyes (Alizarin Red S, Rhodamine B, Crystal Violet, and Malachite Green) and an antibiotic drug, ciprofloxacin, dissolved in solution. Degradation of dye occurred across a wide range of pH levels (pH 3-9). This simple combination was also antimicrobial against both Escherichia coli and Staphylococcus aureus. Electron paramagnetic resonance spectroscopy (EPR) results indicate that singlet oxygen was generated during the reaction between catechol and FeMNP at both pH 3 and 7.4, which was responsible for the degradation of organic compounds and bactericidal features of the microgel. Unlike autoxidation that only occurs at a neutral to basic pH, FeMNP-induced catechol oxidation generated singlet oxygen over a wide range of pH level. Additionally, catechol chelates heavy metal ions, resulting in their removal from solution and repurposed these metal ions for dye degradation. This multifunctional microgel can potentially be used for environmental applications for the removal of organic pollutants and heavy metal ions from wastewater, as well as reducing bacterial infection in biomedical applications.

Facet-, composition- and wavelength-dependent photocatalysis of Ag2MoO4

Faceted β-Ag2MoO4 microcrystals are prepared by controlled nucleation and growth in diethylene glycol (DEG) or dimethylsulfoxide (DMSO). Both serve as solvents for the liquid-phase synthesis and surface-active agents for the formation of faceted microcrystals. Due to its reducing properties, truncated β-Ag2MoO4@Ag octahedra are obtained in DEG. The synthesis in DMSO allows avoiding the formation of elemental silver and results in β-Ag2MoO4 cubes and cuboctahedra. Due to its band gap of 3.2 eV, photocatalytic activation of β-Ag2MoO4 is only possible under UV-light. To enable β-Ag2MoO4 for absorption of visible light, silver-coated β-Ag2MoO4@Ag and Ag2(Mo0.95Cr0.05)O4 with partial substitution of [MoO4]2- by [CrO4]2- were prepared, too. The photocatalytic activity of all the faceted microcrystals (truncated octahedra, cubes, cuboctahedra) and compositions (β-Ag2MoO4, β-Ag2MoO4@Ag, β-Ag2(Mo0.95Cr0.05)O4) is compared with regard to the photocatalytic decomposition of rhodamine B and the influence of the respective faceting, composition and wavelength.

Silver molybdate nanoparticles based immunosensor for the non-invasive detection of Interleukin-8 biomarker

In this study, we report the silver molybdate nanoparticles (β-Ag₂MoO₄ NPs) based non-invasive and sensitive electrochemical immunosensor for label-free detection of Interleukin-8 (IL-8) biomarker. The X-ray diffraction and Raman spectroscopy studies confirm the cubic spinel structures of β-Ag₂MoO₄ NPs. High-resolution transmission electron microscopy study depicted average size of β-Ag₂MoO₄ NPs as 27.15 nm. The cleaned indium tin oxide coated glass substrates were coated with spin-coated thin films of Ag₂MoO₄ NPs. These electrodes used for covalently immobilization of antibodies specific to IL-8 (Anti-IL-8) using EDC-NHS chemistry and unbound activated sites blocked by bovine serum albumin. Electrochemical response was obtained in the range of 1 fg mL^-1 to 40 ng mL^-1 and the sensitivity was found to be 7.03 μA ng^-1mL cm^-2 with LOD of 90 pg mL^-1. Spiked samples prepared by human saliva were tested and found efficient detection with this immunoelectrode.

Unvealing the role of β-Ag2MoO4 microcrystals to the improvement of antibacterial activity

Crystal morphology with different surfaces is important for improving the antibacterial activity of materials. In this experimental and theoretical study, the antibacterial activity of β-Ag₂MoO₄ microcrystals against the Gram-positive bacteria, namely, methicillin-resistant Staphylococcus aureus (MRSA), and the Gram-negative bacteria, namely, Escherichia coli (E. coli), was investigated. In this study, β-Ag₂MoO₄ crystals with different morphologies were synthetized by a simple co-precipitation method using three different solvents. The antimicrobial efficacy of the obtained microcrystals against both bacteria increased according to the solvent used in the following order: water < ammonia < ethanol. Supported by experimental evidence, a correlation between morphology, surface energy, and antibacterial performance was established. By using the theoretical Wulff construction, which was obtained by means of density functional calculations, the morphologies with large exposition of the (001) surface exhibited superior antibacterial activity. This study provides a low cost route for synthesizing β-Ag₂MoO₄ crystals and a guideline for enhancing the biological effect of biocides on pathogenic bacteria by the morphological modulation.

Hierarchical construction and characterization of lanthanum molybdate nanospheres as an unassailable electrode material for electrocatalytic sensing of the antibiotic drug nitrofurantoin

In this work, lanthanum molybdate nanospheres (LMNSs) were prepared by employing a co-precipitation methodology, and their electrochemical activity against nitrofurantoin (NF) was reported.

Selective oxidation of alcohols by using CoFe2O4/Ag2MoO4 as a visible-light-driven heterogeneous photocatalyst

Using a CoFe₂O₄/Ag₂MoO₄ heterostructure as a novel, stable, inexpensive, and reusable photocatalyst with high-performance for the oxidation of alcohols.

A ratiometric fluorometric ciprofloxacin assay based on the use of riboflavin and carbon dots

Carbon dots (CDs) were hydrothermally synthesized from selenious yeast. They were further coupled with riboflavin to form a dually emitting probe for ciprofloxacin (CIP). Under 370 nm excitation, the probe displays dual (blue and green) emissions with peaks at 443 and 510 nm. When CIP is added, the blue fluorescence of the CDs is enhanced while the green fluorescence remains unaffected. The ratio of the relative fluorescence intensities at 443 and 510 nm increases linearly in the 0.5-200 μM CIP concentration range. The fluorescent probe is selective and has a 0.13 μM detection limit. Satisfactory recoveries (97.9-101.1%) were received when the probe was used to quantify CIP in spiked water and human serum samples. Graphical abstractBlue-emissive carbon dots were prepared from selenious yeast via a hydrothermal method, and then coupled with riboflavin as a ratiometric fluorometric probe for ciprofloxacin determination.

Antimicrobial properties of α-Ag2WO4 rod-like microcrystals synthesized by sonochemistry and sonochemistry followed by hydrothermal conventional method

In this study we report the synthesis of silver tungstate microcrystals (α-Ag₂WO₄) by sonochemistry method (SC) at 65 °C and sonochemistry followed by conventional hydrothermal (SC + HC) for 1, 6 and 12 h, at 140 °C. The structural characterization by XRD confirms the alpha phase of the orthorhombic structure and the space group Pn2n, for all synthesized microcrystals. All the actives modes identified at the Raman spectroscopy were characteristic of alpha phase. The optical band gap by UV-Vis spectroscopy using the diffuse reflectance were 2.98, 3.0, 2.99 and 2.96 eV, for the microcrystals SC, SC + HC-1 h, SC + HC-6 h and SC + HC-12 h, respectively. FE-SEM images show the rod-like microcrystals, however, exhibiting the plane surface (1 0 1) only for the synthesized microcrystals with the assistance of the hydrothermal method (SC + HC-1 h, SC + HC- 6 h and SC + HC-12 h). The antimicrobial potential was confirmed for all α-Ag₂WO₄ microcrystals synthesized. However, the SC + HC-12 h microcrystals were more susceptible in the bacterial and fungal inhibition, with MIC values for microorganisms C. albicans, T. rubrum, MRSA e EHEC, 0.2-0.5, 4-9, 250 and 31.25 μg mL^-1, respectively.

In Situ Synthesis, Characterization, and Catalytic Performance of Polypyrrole Polymer-Incorporated Ag2MoO4 Nanocomposite for Detection and Degradation of Environmental Pollutants and Pharmaceutical Drugs

Material combinations of semiconductor with conducting polymer are gaining growing interest due to their enhanced activities in photocatalysis as well as electrochemical sensing. In this present work, we report a facile in situ synthesis of polypyrrole (PPy) polymer-incorporated silver molybdate (Ag₂MoO₄) nanocomposite that is utilized as a photocatalyst and electrocatalyst for the degradation of pollutant heavy metals, namely, methylene blue (MB) and heavy metal (Cr(VI)), and ciprofloxacin (CIP) and for detection of the drug, azomycin. The synthesized nanocomposite was characterized by various theoretical, spectral, and microscopic studies. Matching of the powder X-ray diffraction pattern with JCPDS no. 76-1747 confirmed the formation of α-Ag₂MoO₄/PPy. The surface topography and spherical morphology of the nanocomposite were studied using field emission-scanning electron microscopy and transmission electron microscopy. Fourier transform infrared spectral detail expounds the smooth incorporation of PPy to Ag₂MoO₄. The as-synthesized nanocomposite performs as an efficient photocatalyst in the degradation of MB (99.9%), Cr(VI) (99%), and CIP drug (99.8%) within 10 min. In addition to this, the Ag₂MoO₄/PPy-modified glassy carbon electrode (GCE) demonstrated excellent electrocatalytic activity in terms of a higher cathodic peak current and lower peak potential when compared with other modified and unmodified GCEs for the detection of azomycin. The Ag₂MoO₄/PPy/GCE displayed a broader linear response range and lower detection limit of 0.5-499 μM and 65 nM, respectively. Moreover, other potentially co-interfering compounds, such as a similar functional group-containing biological substances and inorganic species, have no interference effect toward azomycin sensing.

Solar light active silver/iron oxide/zinc oxide heterostructure for photodegradation of ciprofloxacin, transformation products and antibacterial activity

This paper reports on the multitasking potential of a silver/iron oxide/zinc oxide (Ag/Fe₂O₃/ZnO) heterostructure, which was used for the photocatalytic decomposition of ciprofloxacin (CPX) and bacterial disinfection. The Ag/Fe₂O₃/ZnO heterostructure was successfully prepared using a facile precipitation method, and characterization results showed interesting structural, morphological, compositional and luminescent properties. The morphological results of the prepared heterostructure confirmed the deposition of Ag nanoparticles onto the surface of ZnO nanoplates and Fe₂O₃ nanorods. Treatment studies showed that the Ag/Fe₂O₃/ZnO heterostructure had superior solar light driven photocatalytic activity towards CPX degradation (76.4%) compared to bare Fe₂O₃ nanorods (43.2%) and ZnO nanoplates (63.1%), Ag/Fe₂O₃ (28.2%) and Ag/ZnO (64.5%) under optimized conditions (initial CPX concentration: 10 mg/L; pH 4; catalyst loading: 0.3 g/L). Reactive species study confirmed the roles of e^-, h⁺, OH and O₂^- in the photocatalytic degradation process. This photocatalytic behaviour of the Ag/Fe₂O₃/ZnO heterostructure could be attributed to the improved full solar spectrum harvesting capacity, separation of charge carriers and migration of e^-/h⁺ across the heterostructure interface. In addition, the Ag/Fe₂O₃/ZnO heterostructure also showed good antibacterial activity against Escherichia coli (E. coli) under both dark and visible light conditions. This might be due to generation of reactive oxygen species during the reaction. To the best of our knowledge, this is the first study till date on the utilization of Ag/Fe₂O₃/ZnO heterostructure for the photocatalytic degradation of CPX and E. coli bacteria disinfection. Therefore, this work offers an attractive path to design ZnO-based ternary heterostructures for solar-driven applications in wastewater remediation.