An eco-friendly and high-yield extraction of rare earth from the leaching solution of ion adsorbed minerals

Ion-adsorbed rare earth minerals are rich in medium and heavy rare earth (RE), which are important strategic resources. In this article, a novel approach for the extraction of RE from ion adsorbed minerals was developed. Through a comprehensive assessment of their extraction and separation performance, the hydrophobic deep eutectic solvents (HDES) with a composition of trioctylphosphine oxide (TOPO): dodecanol (LA): 2-thiophenoyltrifluoroacetone (HTTA) = 1:1:1 was determined as the optimal configuration. Under optimized conditions, only RE were extracted by the HDES, while Al, Ca, Mg were not extracted at all. The HDES based extraction obviated the need for diluent such as kerosene, eliminating the generation of impurity removal residues. The RE in the stripping solution could be successfully enriched by saponified lauric acid, achieving an impressive precipitation rate of 99.7%. The RE precipitate underwent further enrichment, resulting in a RE concentration of 176 g/L (REO = 210 g/L). Unlike industrial precipitants such as oxalic acid and ammonium bicarbonate, lauric acid can be effectively recycled, thereby avoiding a large amount of wastewater and carbon dioxide emissions. The obtained RE solution product exhibits high yield and purity, this study provides an eco-friendly and high-yield approach for extracting RE.

Developing of an eco-friendly liquid-liquid microextraction method by using menthol-based hydrophobic deep eutectic solvent for determination of basic fuchsin dye: assessment of the greenness profile

Herein, we aimed to develop a new environmentally friendly liquid-liquid microextraction (LLME) method based on hydrophobic deep eutectic solvent (hDES) synthesized using biodegradable dl-menthol and decanoic acid for the spectrophotometric determination of toxic basic fuchsin dye in environmental water samples. The parameters affecting the extraction efficiency such as pH, mole ratio, and volume of hDES (1:2) and type and volume of organic solvent, sample volume, times of vortex, ultrasonic bath and centrifuge, ionic strength, and matrix effect were investigated and optimized. Under optimal conditions, the calibration curve showed linearity in the range of 7.4-167 μg L-1 with a coefficient of determination of 0.9994. The limit of detection, intra-day and inter-day precision, and recovery values were 2.25 μg L-1, 2.46% and 4.45%, and 105 ± 3%, respectively. The preconcentration and enrichment factors were found to be 30 and 61.5, respectively. The proposed hDES-LLME methodology was successfully applied to the environmental water samples to detect toxic BF dye (95-105%). Finally, the ecological impact of the suggested method was evaluated using the analytical eco-scale (PPS:88), complementary green analytical procedure indexe (ComplexGAPI), and the Analytical GREEnness tool (0.63). The assessment results showed that the presented analytical method can be regarded as a green LLME approach for the determination of the BF in water.

Solute dynamics of a hydrophobic molecule in a menthol-thymol based type-V deep eutectic solvent: effect of composition of the components

Type-V deep eutectic solvents (DESs) are a newly emerging unique class of solvents obtained by physical mixing and heating of non-ionic components. These solvents show deviation from the thermodynamic ideality. Compared to type-I to IV DESs, type-V DESs are less explored and their physical chemistry is in its nascent stage. In this work, we have chosen a type-V DES based on menthol-thymol (MT) for our working media. Solvent and rotational dynamics were studied with varying temperature using a well-known solvatochromic probe, Coumarin 153 (C153). We prepared the MT-based DES using a reported procedure at three molar ratios: 1 : 1 (M1T1), 1 : 1.5 (M1T1.5), and 2 : 1 (M2T1) of menthol (M) and thymol (T). Time-resolved emission spectra (TRES) were constructed with varying temperature. Utilizing TRES, the decay of the solvent correlation function (C(t)) was plotted. We have correlated the solvent relaxation time in these DESs as a function of viscosity. The time-resolved anisotropy decays were also collected to perceive the rotational relaxation dynamics of C153 as a function of temperature. The decay of solvent relaxation was found to be bi-exponential, and the average solvation time (〈τs〉) in M2T1 was found to be longer than those of M1T1.5 and M1T1. The rotational reorientation times (〈τrot〉) also follow the same trend. We have analysed the rotational dynamics of C153 in type-V DESs employing the Stokes-Einstein-Debye (SED) hydrodynamic model. The rotational dynamics in DESs demonstrate a good correlation with the SED model with a little deviation. In MT-based DESs, the solute's rotational relaxation times approach hydrodynamic stick boundary condition at low viscosity (or at high temperatures) for all molar compositions. Using the Arrhenius-type equations, we have correlated the activation energies for the rotational motion of C153, along with the viscous flow and non-radiative pathways for all the DESs.

Effect of water addition on caprylic acid: Quaternary ammonium salts (QAS) deep eutectic solvents: Characterization of their structural and dynamical properties

Physicochemical properties of the binary mixtures based on Caprylic acid: Quaternary ammonium salts (QAS) (7:3 mol ratio) are investigated using MD simulations. Considering the hydrophobic character of eutectic solvents based on long-chain fatty acids, the stability of the binary mixtures was investigated in the adjacent water. In order to investigate the effect of water on intermolecular interactions in binary mixtures, the structural properties of the binary mixtures in the pure state and adjacent to water were investigated at 310 K. Assessed structural properties include the combined distribution functions (CDFs), the radial distribution functions (RDFs), the angular distribution functions (ADFs), and the Hydrogen bonding network between HBA and HBD and Spatial distribution functions (SDF). We aimed to represent the structural stability of eutectic solvents based on Caprylic acid and Quaternary ammonium salts (QAS) as a function of the alkyl chain length of cations, the evidence was found for the interaction between the chloride anion leads to the transition of HBA to the water-rich phase. The alkyl chain length of cations of Quaternary ammonium salts shows the stability of eutectic solvents in the adjacent water.

A sustainable strategy for targeted extraction of thorium from radioactive waste leachate based on hydrophobic deep eutectic solvent

In this work, the new hydrophobic deep eutectic solvents (HDESs) based on 2-hexyldecanoic acid (HDA) as a hydrogen bond donor (HBD) were used to selectively enrich trace Th from radioactive waste leach solution. These HDESs are characterized by low toxicity, bio-friendliness, low viscosity and sufficient hydrophobicity. Compared with Al, Mg, Ca and RE, HDESs exhibited exceptional selectivity for Th extraction, along with high loading capacity, easy stripping and stable reusability. The mechanism of Th extraction by the HDES is a cation exchange reaction. Based on the thymol (TL):HDA (1:3) HDES, a short flow closed-loop recovery process of Th in the leach solution of radioactive waste residue was developed. After a single-step extraction, the extraction percentage (E%) of Th exceeded 98.0%, while the E% of other elements was less than 0.14%. After stripping, the concentration of Th in the concentrated solution reached 2.16 × 103 mg/L with a purity of 74.2%, which could be directly used for subsequent purification. By adjusting the pH to 4.00, the raffinate was used as a feed solution for RE elements recovery. The HDES-based extraction strategy for Th is simple, safe, efficient and environmentally friendly, providing a new idea for the recovery of radioactive waste residues.

Green solvent mediated extraction of micro- and nano-plastic particles from water

The production of plastic and the amount of waste plastic that enters the ecosystem increases every year. Synthetic plastics gradually break down into particles on the micro- and nano-scale in the environment. The micro- and nano-plastics pose a significant ecological threat by transporting toxic chemicals and causing inflammation and cellular damage when ingested; however, removal of those particles from water is challenging using conventional separation methods. Deep eutectic solvents (DES), a new class of solvents composed of hydrogen bond donors and acceptors, have been proposed as a cheaper alternative to ionic liquids. Hydrophobic DES derived from natural compounds (NADES) show promise as extractants in liquid-liquid extractions. This study investigated the extraction efficiency of micro- and nano-plastics including polyethylene terephthalate, polystyrene, and a bioplastic polylactic acid from fresh water and saltwater using three hydrophobic NADES. The extraction efficiencies fall in a range of 50-93% (maximum % extraction) while the extraction rates fall between 0.2 and 1.3 h (as indicated by the time to extract half the theoretical maximum). Molecular simulations show a correlation between the extraction efficiency and the association between the plastics and NADES molecules. This study demonstrates the potential of hydrophobic NADES as extractants for removal of different micro- and nano-plastic particles from aqueous solutions.

Hydrophobic Deep Eutectic Solvents as Greener Substitutes for Conventional Extraction Media: Examples and Techniques

Deep eutectic solvents (DESs) are multicomponent designer solvents that exist as stable liquids over a wide range of temperatures. Over the last two decades, research has been dedicated to developing noncytotoxic, biodegradable, and biocompatible DESs to replace commercially available toxic organic solvents. However, most of the DESs formulated until now are hydrophilic and disintegrate via dissolution on coming in contact with the aqueous phase. To expand the repertoire of DESs as green solvents, hydrophobic DESs (HDESs) were prepared as an alternative. The hydrophobicity is a consequence of the constituents and can be modified according to the nature of the application. Due to their immiscibility, HDESs induce phase segregation in an aqueous solution and thus can be utilized as an extracting medium for a multitude of compounds. Here, we review literature reporting the usage of HDESs for the extraction of various organic compounds and metal ions from aqueous solutions and absorption of gases like CO₂. We also discuss the techniques currently employed in the extraction processes. We have delineated the limitations that might reduce the applicability of these solvents and also discussed examples of how DESs behave as reaction media. Our review presents the possibility of HDESs being used as substitutes for conventional organic solvents.

Novel and Highly Sensitive Electrochemical Sensor for the Determination of Oxytetracycline Based on Fluorine-Doped Activated Carbon and Hydrophobic Deep Eutectic Solvents

Residues of oxytetracycline (OTC), a veterinary antibiotic and growth promoter, can be present in animal-derived foods; their consumption is harmful to human health and their presence must therefore be detected and regulated. However, the maximum residue limit is low, and consequently highly sensitive and accurate detectors are required to detect the residues. In this study, a novel highly sensitive electrochemical sensor for the detection of OTC was developed using a screen-printed electrode modified with fluorine-doped activated carbon (F-AC/SPE) combined with a novel deep eutectic solvent (DES). The modification of activated carbon by doping with fluorine atoms (F-AC) enhanced the adsorption and electrical activity of the activated carbon. The novel hydrophobic DES was prepared from tetrabutylammonium bromide (TBABr) and a fatty acid (malonic acid) using a green synthesis method. The addition of the DES increased the electrochemical response of F-AC for OTC detection; furthermore, it induced preconcentration of OTC, which increased its detectability. The electrostatic interactions between DES and OTC as well as the adsorption of OTC on the surface of the modified electrode through H-bonding and π-π interactions helped in OTC detection, which was quantified based on the decrease in the anodic peak potential (E _pa = 0.3 V) of AC. The electrochemical behavior of the modified electrode was investigated by cyclic voltammetry, differential pulse voltammetry, and electrochemical impedance spectroscopy. Under optimum conditions, the calibration plot of OTC exhibited a linear response in the range 5-1500 μg L^-1, with a detection limit of 1.74 μg L^-1. The fabricated electrochemical sensor was successfully applied to determine the OTC in shrimp pond and shrimp samples with recoveries of 83.8-100.5% and 93.3-104.5%, respectively. In addition to the high sensitivity of OTC detection, the proposed electrochemical sensor is simple, cost-effective, and environmentally friendly.

High-efficiency leaching of valuable metals from waste Li-ion batteries using deep eutectic solvents

With the penetration of lithium-ion batteries (LIBs) into electric vehicles, the recycling of waste LIBs is inevitable from the perspective of health, economy and environmental protection. Herein is reported a novel green method for extracting valuable metals from the cathode of LIBs, in which the Deep Eutectic Solvent (DES) is used as leachate to dissolve electrode material waste. Mixing choline chloride (ChCl) and malonic acid is helpful to effectively improve the reduction ability of DES, resulting in superior leaching efficiency. At the lower temperature (100 °C), the leaching efficiency of cobalt and lithium reached up to 98.61% and 98.78%, respectively. X-ray absorption near edge structure (XANES) spectroscopy demonstrated that DESs could act as both leachate and reducing agent, which could destroy the covalent bonds of metal oxides to form a cobalt (II)-chlorine complex. This method is straightforward to operate and does not involve the additional reducing agents, which is held promise to bring economic and sustainable development prospects in the field of lithium battery development.

Deep Eutectic Solvents for Extraction and Preconcentration of Organic and Inorganic Species in Water and Food Samples: A Review

Deep eutectic solvents (DESs) have been developed as green solvents and these are capable as alternatives to conventional solvents used for the extraction of organic and inorganic species from food and water samples. The continuous generation of contaminated waste and increasing concern for the human health and environment have compelled the scientific community to investigate more ecological schemes. In this concern, the use of DESs have developed in one of the chief approach in the field of chemistry. These solvents have appeared as a capable substitute to conventional hazardous solvents and ionic liquids. The DESs has distinctive properties, easy preparation and components availability. It is not only used in scienctific fields but also used in quotidian life. There are many advantages of DESs in analytical chemistry, they are largely used for extraction and determination of inorganic and organic compounds from different samples. In previous a few years, several advanced researches have been focused on the separation and preconcentration of low level of pollutants using DESs as the extractants. This review summarizes the use of DESs in the separation and preconcentration of organic and inorganic species from water and food samples using various microextraction processes.

An Overview of Structure and Dynamics Associated with Hydrophobic Deep Eutectic Solvents and Their Applications in Extraction Processes

Recent development of novel water-immiscible green solvents known as hydrophobic deep eutectic solvents (HDESs) has opened the gates for applications requiring media where presence of water is undesirable. Ever since they were prepared, researchers have used HDESs in diverse fields such as extraction processes, CO 2 sequestration, membrane formation, and catalysis. The microstructure and dynamics associated with the species comprising HDESs guide their suitability for specific applications. For example, varying the alkyl tail length of HDES components significantly affects the dynamics of the components and thus helps in tuning the efficiency of extraction processes. The development of HDESs is still in infancy and very few theoretical studies are available in the literature that help in understanding the structure and dynamics of HDESs. This review highlights the recent work focused on the microscopic structure and dynamics of HDESs and their potential applications, particularly in extraction processes. We have also provided a glimpse of how the integration of experiments and computational techniques can help understand the mechanism of extraction processes.

Perspectives of Using DES-Based Systems for Solid–Liquid and Liquid–Liquid Extraction of Metals from E-Waste

In recent years, the linear economic model and global warming have shown that it is necessary to move toward a circular economic model. In this scenario, the recycling of waste electrical and electronic equipment (WEEE) with green processes is one of the pending tasks; thus, in the present review, advances in the solid–liquid and liquid–liquid extraction processes, processes among the most important for the recovery of metals from ores or WEEE, with green solvents such as deep eutectic solvents (DES) are presented and analyzed, identifying the present and future challenges. To date, most articles focused on one of the processes, be it solid–liquid or liquid–liquid extraction, while few reports included the entire hydrometallurgical process, which could be due to heterogeneity of the WEEE, a characteristic that influences determining the leaching kinetic and the leaching mechanisms. A deeper understanding of the phenomenon would help improve this process and the next stage of liquid–liquid extraction. This also leads to the fact that, at the liquid–liquid extraction stage, most articles considered synthetic pregnant leach solutions to evaluate each of the variables, whereas the stripping of the ions and the recycling of the DESs in continuous processes is a challenge that should be addressed in future work. From the analysis, for WEEE leaching, it was identified that acid DESs are those achieving the best extraction percentages in the leaching of copper, lithium, and cobalt, among others, where the most studied hydrogen bond acceptor (HBA) is choline chloride with an acid (e.g., citric or lactic acid) as the hydrogen bond donor (HBD). For the liquid–liquid extraction of ions is a greater variety of HBAs (e.g., lidocaine, trioctylphosphine oxide and triphenyl phosphate) and HBDs (e.g., decanoic acid, thenoyltrifluoroacetone, and benzoyltrifluoroacetone) used; however, studies on the extraction of cobalt, lithium, copper, and nickel stand out, where the pH and temperature parameters have great influence.

A Sustainable Strategy for Solid-Phase Extraction of Antiviral Drug from Environmental Waters by Immobilized Hydrogen Bond Acceptor

Deep eutectic solvents are a new generation of green solvents composed of hydrogen bond acceptors and donors. However, when used as extractants in liquid–liquid separation, they are difficult to recycle and easy to lose. In order to solve these problems, herein, immobilized hydrogen bond acceptor adsorbent material was prepared for the separation and enrichment of antiviral drug arbidol from seven kinds of environmental water samples by in situ formation of hydrophobic deep eutectic solvents. The structure, morphology and thermal stability of the adsorbents were characterized, the separation and enrichment conditions for the targeted analyte were optimized, and the adsorption thermodynamics and kinetics were investigated. It was found that the adsorbent material could effectively enrich trace arbidol with the recovery more than 95% at the concentration above 7.5 ng/mL, and the enrichment factor was as high as 634.7. Coexisting substances, such as NaCl, KCl, CaCl₂ and MgCl₂, did not interfere with the adsorption of arbidol, even if their concentration was high, up to 1.0 mol/L, and the relative recovery for real samples was in the range from 92.5% to 100.3%. Furthermore, the immobilized hydrogen bond acceptor could be recycled and reused, and the recovery of arbidol was still above 95% after 12 adsorption–desorption cycles. The mechanism study demonstrates that the synergistic effect of hydrogen bonding and π-π stacking is the primary factor for the high adsorption efficiency.

Neoteric deep eutectic solvents: history, recent developments, and catalytic applications

Deep eutectic solvents (DESs) are modified versions of ionic liquids (ILs) and are formed by the fusion of polar components (liquids or solids) via hydrogen bonding interactions. DESs are prepared by the simple mixing of two or three cheap constituents (that are capable of self-association) with gentle heating, which leads to a drastic decrease in their melting points. The resultant clear homogeneous mixture consists of cations, anions, as well as neutral molecules; this will contribute both ionic and molecular solvent properties to the DESs. DESs have emerged as alternatives to conventional organic solvents and ILs, which meet different criteria such as availability, low cost, low toxicity, biodegradability, recyclability, ease of preparation method, tunable, and designer physiochemical properties. Many of them have attracted considerable attention and haave been applied in distinct fields of chemistry. To summarize the full-scale development of DESs, this review discusses the history, classifications, various methods of preparation, properties, and some major applications in catalysis in the last three years. This review is expected to be helpful for the further development of DESs based on a summary of the fundamental research in the field.

Systematic evaluation of hydrophobic deep eutectic solvents as alternative media for the extraction of metal ions from aqueous solution

The recent development of hydrophobic deep eutectic solvents (HDESs) has led to growing interest in these reagents as possible environmentally benign replacements for conventional organic media in a host of applications, among them metal ion separations by liquid-liquid extraction. To evaluate the potential utility of these novel solvents in this application, a systematic examination of the facilitated transfer of selected alkali and alkaline earth cations into representative HDESs from aqueous solution in the presence of a macrocyclic polyether (i.e., a crown ether) has been undertaken. Comparison of the results to those obtained for a series of oxygenated, aliphatic solvents (n-alcohols) and for several 1-alkyl-3-methylimidazolium-based ionic liquids (ILs) under the same conditions indicate that despite frequent suggestions that some HDESs resemble ILs, metal ion distribution in HDES-aqueous systems more closely mimics that seen for the alcohols. Metal ion partitioning in these systems appears less dependent on the water content of the organic phase and on structural variations in the solvent than is the case for either alcohols or ionic liquids, however. The implications of these results for the design and application of HDES-based extraction systems for metal ions are described.

Vortex-assisted dispersive liquid-liquid microextraction based on the solidification of sedimentary deep eutectic solvents for the determination of triazine and phenylurea herbicides in milk samples

Vortex-assisted dispersive liquid-liquid microextraction based on the solidification of sedimentary deep eutectic solvents was developed and applied to the extraction of triazine and phenylurea herbicides in milk samples. In this study, a series of novel hydrophobic deep eutectic solvents were prepared using tetrabutylammonium chloride as the hydrogen bond acceptor and perfluorooctanol as the hydrogen bond donor, and their structures, viscosities, densities and melting points were determined. The deep eutectic solvent was used as the extraction solvent and dispersed in the sample solution with the assistance of vortex. After extraction, through centrifugation and subsequent cooling in an ice bath, the deep eutectic solvent was solidified and deposited on the bottom of the centrifuge tube. Subsequently, the deep eutectic solvent combined with the target analytes was diluted and used for chromatographic analysis. Some parameters, including the extraction temperature, type and volume of the deep eutectic solvent, amount of NaCl, vortex time and pH of the sample solution, were optimized by the single-factor experiment, Plackett-Burman design and Box-Behnken design. The limits of detection and quantification were in the range of 0.41-0.59 μg L^-1 and 1.37-1.95 μg L^-1, respectively. The intra-day precision and inter-day precision were in the range of 0.28-2.14% and 2.02-7.99%, respectively. The present method was successfully applied to the determination of triazine and phenylurea herbicides in milk samples.

Spectroscopic Study into Lanthanide Speciation in Deep Eutectic Solvents

Deep eutectic solvents are a new class of green solvents that are being explored as an alternative for used nuclear fuel and critical material recycling. However, there is a paucity of knowledge regarding metal behavior in them. This paper explores the underlying chemistry of rare-earth elements in choline chloride-based deep eutectic solvents by using a multi-technique spectroscopic methodology. Results show that speciation is highly dependent on the choice of the hydrogen-bond donor. Collected EXAFS data showed Ln3+ coordination with ethylene glycol and urea in their respective solvents and coordination with chloride in the lactic acid system. Generalized coordination environments were determined to be [LnL4-5], [LnL7-10], and [LnL5-6] in the ethylene glycol, urea, and lactic acid systems, respectively. Collected UV/vis spectra for Nd3+ and Er3+ showed variations with changing solvents, showing that Ln-Cl interactions do not dominate in these systems. Luminescence studies were consistent, showing varying emission spectra with varying solvent systems. The shortest luminescent lifetimes were observed in the choline chloride-ethylene glycol deep eutectic solvent, suggesting coordination through O-H groups. Combining all collected data allowed Eu3+ coordination geometries to be assigned.

Application of Extraction and Determination Based on Deep Eutectic Solvents in Different Types of Environmental Samples

Water sources are an indispensable resource for human survival. Monitoring the pollution status of the surrounding environment is necessary to protect water sources. Research on the environmental matrix of deep eutectic solvents (DESs) has expanded rapidly because of their high extraction efficiency for various target analytes, controllable synthesis, and versatile structure. Following the synthesis of hydrophobic deep eutectic solvents (HDESs), their application in aqueous matrices broadened greatly. The present review conducted a survey on the pollutant extraction methods based DESs in environmental matrices from two aspects, application methods and matrix types; discussed the potential risk of DESs to the environment and future development trends; and provided some references for researchers to choose DES-based extraction methods for environmental research.

New Solvents for CO2 and H2S Removal from Gaseous Streams

Acid gas removal from gaseous streams such as flue gas, natural gas and biogas is mainly performed by chemical absorption with amines, but the process is highly energy intensive and can generate emissions of harmful compounds to the atmosphere. Considering the emerging interest in carbon capture, mainly associated with increasing environmental concerns, there is much current effort to develop innovative solvents able to lower the energy and environmental impact of the acid gas removal processes. To be competitive, the new blends must show a CO2 uptake capacity comparable to the one of the traditional MEA benchmark solution. In this work, a review of the state of the art of attractive solvents alternative to the traditional MEA amine blend for acid gas removal is presented. These novel solvents are classified into three main classes: biphasic blends—involving the formation of two liquid phases, water-lean solvents and green solvents. For each solvent, the peculiar features, the level of technological development and the main expected pros and cons are discussed. At the end, a summary on the most promising perspectives and on the major limitations is provided.

Hydrogen Bonding and Vaporization Thermodynamics in Hexafluoroisopropanol-Acetone and -Methanol Mixtures. A Joined Cluster Analysis and Molecular Dynamic Study

Binary mixtures of hexafluoroisopropanol with either methanol or acetone are analyzed via classical molecular dynamics simulations and quantum cluster equilibrium calculations. In particular, their populations and thermodynamic properties are investigated with the binary quantum cluster equilibrium method, using our in‐house code peacemaker 2.8, upgraded with temperature‐dependent parameters. A novel approach, where the final density from classical molecular dynamics, has been used to generate the necessary reference isobars. The hydrogen bond network in both type of mixtures at molar fraction of hexafluoroisopropanol of 0.2, 0.5, and 0.8 respectively is investigated via the molecular dynamics trajectories and the cluster results. In particular, the populations show that mixed clusters are preferred in both systems even at 0.2 molar fractions of hexafluoroisopropanol. Enthalpies and entropies of vaporization are calculated for the neat and mixed systems and found to be in good agreement with experimental values.

Preparation of a novel environmentally friendly hydrophobic deep eutectic solvent ChCl-THY and its application in removal of hexavalent chromium from aqueous solution

A liquid-liquid extraction methodology was developed for the removal of Cr(VI) from contaminated water using a novel green hydrophobic deep eutectic solvent (DES) as an efficient sole extracting agent. The hydrophobic DES was obtained by mixing choline chloride and thymol in 1:4 molar ratio at 70°C for 10 min and was denoted as ChCl-THY(1:4). The ChCl-THY(1:4) works efficiently for removal of high (20 mg/L) and low (500 µg/L) concentration of Cr(VI) from artificially contaminated natural water with >95% extraction efficiency (E%) at optimized reaction conditions (pH 2-6, 40°C). The DES was characterized by ¹ H NMR and FTIR spectroscopy, and the data suggest that interaction occurs between Cl^- ion of choline chloride and H atoms of thymol molecules. Physicochemical properties such as density, melting point, moisture, and solubility were studied and discussed. Herein, no sharp melting point was observed for ChCl-THY(1:4) in DSC curve. DES was regenerated using 0.1 M NaOH as stripping agent, and 50%-60% extraction efficiency could be attained in the next cycle. A plausible mechanism of interaction between Cr(VI) species and DES was also explored with the help of FTIR spectroscopy. PRACTITIONER POINTS: A novel hydrophobic DES (ChCl-THY) is prepared by mixing choline chloride and thymol at 1:4 molar ratio. ChCl-THY(1:4) is employed for the first time as sole extracting agent to remove the Cr(VI) from contaminated aqueous solution. >95% extraction efficiency was achieved by ChCl-THY(1:4) in natural water conditions at µg/L and mg/L level of contamination. Both the component used to prepare the DES are naturally abundant; hence, DES is not toxic for biota. The element present in natural water did not show any interference with extraction of Cr(VI).

Multiple evidences of dynamic heterogeneity in hydrophobic deep eutectic solvents

Hydrophobic deep eutectic solvents (HDESs) have gained immense popularity because of their promising applications in extraction processes. Herein, we employ atomistic molecular dynamics simulations to unveil the dynamics of DL-menthol (DLM) based HDESs with hexanoic (C6), octanoic (C8), and decanoic (C10) acids as hydrogen bond donors. The particular focus is on understanding the nature of dynamics with changing acid tail length. For all three HDESs, two modes of hydrogen bond relaxations are observed. We observe longer hydrogen bond lifetimes of the inter-molecular hydrogen bonding interactions between the carbonyl oxygen of the acid and hydroxyl oxygen of menthol with hydroxyl hydrogen of both acids and menthol. We infer strong hydrogen bonding between them compared to that between hydroxyl oxygen of acids and hydroxyl hydrogens of menthol and acids, marked by a faster decay rate and shorter hydrogen bond lifetime. The translational dynamics of the species in the HDES becomes slower with increasing tail length of the organic acid. Slightly enhanced caging is also observed for the HDES with a longer tail length of the acids. The evidence of dynamic heterogeneity in the displacements of the component molecules is observed in all the HDESs. From the values of the α-relaxation time scale, we observe that the molecular displacements become random in a shorter time scale for DLM-C6. The analysis of the self-van Hove function reveals that the overall distance covered by DLM and acid molecules in the respective HDES is more than what is expected from ideal diffusion. As marked by the shorter time scale associated with hole filling, the diffusion of the oxygen atom of menthol and the carbonyl oxygen of acid from one site to the other is fastest for hexanoic acid containing HDES.