A mini-review on the research progress and application of nanomaterials in electrochemiluminescent sensors in the detection of water environmental pollutants

With the increasingly serious problem of environmental pollution, the development of new and efficient detection technology has become an urgent need. Electrochemiluminescence (ECL) sensors have attracted wide attention in environmental pollution detection due to their advantages of low cost, fast analysis speed, high sensitivity, and good selectivity. At the same time, with the rapid development of nanotechnology, nanomaterials are widely used to construct ECL sensors. Based on the different roles of nanomaterials in the construction of ECL sensors, they can be summarized as (1) nanomaterials for signal amplification; (2) ECL nanoemitters; (3) Nanomaterials as receptors for ECL resonance energy transfer. In this paper, the construction and luminescence mechanism of ECL sensors are discussed from the above three aspects. Finally, the challenges and prospects of nanomaterials ECL sensors in the field of environmental pollution detection in the future are discussed.

Electrochemiluminescence sensor for organophosphorus pesticides based on the regulation of resonance energy transfer between negative charged gold nanorods and Ru(bpy)32

Combined the electrostatic interaction of the negatively charged gold nanorods (AuNRs) (as acceptor) and Ru(bpy)32+ (as donor), an electrochemiluminescence resonance energy transfer (ECL-RET) sensor was constructed and applied for the detection of organophosphorus pesticides (OPs). Negatively charged AuNRs were synthesized by modifying AuNRs with polystyrene sulfonate (PSS) firstly, which can bind to Ru(bpy)32+ through electrostatic interaction so that the luminophore was absorbed by the acceptor, the resonance energy transfer occurred and only low ECL signal had been detected. Thiocholine can be produced by the hydrolysis process of acetylthiocholine (ATCh) with the help of acetylcholinesterase (AChE), which can bond with PSS-modified AuNRs (PSS-AuNRs) through gold-sulfur interaction, this caused the releasing of the adsorbed Ru(bpy)32+ into the solution and resulting in the restoration of the ECL intensity. However, the activity of AChE was inhibited by OPs, and the recovery process of the ECL signal was thus suppressed as well. In this study, chlorpyrifos was chosen as model target, the results indicated that the correlation between the ECL intensity and the logarithm of chlorpyrifos concentration showed remarkable linearity across 1 ng/mL to 1 mg/mL, achieving a detection limit of 0.51 ng/mL. The proposed system has been utilized for detecting OPs in real samples with satisfied results.

An in situ ratiometric fluorescence immunosensor via Mn2+-triggered aggregation-induced emission transformation of levodopa fluorescent copolymer nanoparticles

Herein, a direct in situ alkaline phosphatase (ALP)-labeled luminescent nanoimmunoassay platform was constructed using Mn2+-triggered aggregation-induced emission transformation of levodopa fluorescent copolymer (LFC) nanoparticles. Using cardiac troponin I (cTn I) as the model antigen, the proposed nanoimmunosensor has been applied to detect cTn I in clinical samples with satisfactory results.

Electrochemiluminescent evaluation of GLUT4 expression in rat adipocytes induced by Ganoderma lucidum polysaccharides

Glucose transporter 4 (GLUT4) directly facilitates cellular uptake of glucose and plays a crucial role in mammalian adipose tissue glucose metabolism. In this work, we constructed a cytosensor for sensitive electrochemiluminescence (ECL) detection of GLUT4 in rat adipocytes (RA cells). A carbon nanotube sponge (CNTSP) was selected to fabricate a permeable electrode to overcome the steric hindrance of cells on the electrode. The expression of GLUT4 after treatment with Ganoderma lucidum polysaccharide (GLP) was assessed by analyzing the luminescence emitted from cell-surface ECL probes. Our preliminary results suggest that GLP promote the expression of GLUT4, thereby enhancing the uptake of the fluorescent glucose 2-NBDG. Treatment with GLP affected GLUT4 expression in RA cells in a dose-dependent manner. Additionally, the ECL cytosensor contributes to the development of ECL imaging of receptors on the cell surface for clinical drug evaluation.

Dual-target nucleic acid sequences responsive electrochemiluminescence biosensor using single type carbon dots as probe for SARS-CoV-2 detection based on series catalytic hairpin assembly amplification

Severe acute respiratory syndrome coronavirus (SARS-CoV-2) is rampant all over the world, and rapid and effective virus detection is the best auxiliary to curb the spread of the epidemic. A diagnosis can only be made if two or more different nucleic acid sequences are confirmed at the same time, and in most of traditional detection technologies, these target sequences have been detected separately. In this work, an electrochemiluminescent (ECL) biosensor employing a single ECL probe as signal output and responding to dual-target simultaneously is proposed for the first time. Taking the two sequences located in ORF 1ab region and N region of SARS-CoV-2 gene sequence as the model target and nitrogen doped carbon quantum dots (CDs) as ECL beacon, supplemented with catalytic hairpin assembly (CHA) reaction for signal amplification, the presented strategy has been successfully applied to the rapid detection of SARS-CoV-2. The developed SARS-CoV-2 biosensor based on the series CHA systems can realize the quantitative determination of SARS-CoV-2 in the range of 50 fM to 200 pM within 40 min. Moreover, the clinical validity of this method has been verified by the high consistency between the detection results of using this method and those using RT-qPCR for seven clinical pharyngeal swab samples.

Plasmon-Boosted Fe, Co Dual Single-Atom Catalysts for Ultrasensitive Luminol-Dissolved O2 Electrochemiluminescence Detection of Prostate-Specific Antigen

Improving the sensitivity of electrochemiluminescence (ECL) systems is highly desired for in vitro ECL diagnosis and bio-detections due to the often-low content of biomarkers in diseases. And dissolved O₂ (DO) as a co-reactant is considered superior to H₂O₂ in the most commonly used luminol ECL systems due to better stability and low biotoxicity, but it still suffers from low ECL performance due to the low reactivity of DO. In this study, an efficient luminol-DO ECL system was developed through the complexing of Fe, Co dual single-atom catalysts (D-SACs) supported by N-doped graphene with the luminol-capped Ag nanoparticles (AgNPs). Benefiting from the electronic interaction between Fe and Co metal sites in the relevant D-SACs and plasmon enhancement of AgNPs, the performance of the corresponding ECL system could be significantly boosted up to ≈677-fold under optimal testing conditions, comparable to the classic luminol-O₂ system. Furthermore, the developed luminol-DO ECL system was successfully applied for the stable ultrasensitive detection of prostate-specific antigen (PSA) in a wide linear range of 1 fg/mL to 1 μg/mL, with a low limit of detection (0.98 fg/mL).

Gold nanoparticle-based signal amplified electrochemiluminescence for biosensing applications

Since the content levels of biomarkers at the early stage of many diseases are generally lower than the detection threshold concentration, achieving ultrasensitive and accurate detection of these biomarkers is still one of the major goals in bio-analysis. To achieve ultrasensitive and reliable bioassay, it requires developing highly sensitive biosensors. Among all kinds of biosensors, electrogenerated chemiluminescence (ECL) based biosensors have attracted enormous attention due to their excellent properties. In order to improve the performance of ECL biosensors, gold nanoparticles (Au NPs) have been widely utilized as signal amplification tags. The introduction of Au NPs could dramatically enhance the performance of the constructed ECL biosensors via diverse ways such as electrode modification material, efficient energy acceptor in ECL resonant energy transfer (ECL-RET), reaction catalyst, surface plasmon resonance (SPR) enhancer, and as nanocarrier. Herein, we summarize recent developments and progress of ECL biosensors based on Au NPs signal amplification strategies. We will cover ECL applications of Au NPs as a signal amplification tag in the detection of proteins, metal ions, nucleic acids, small molecules, living cells, exosomes, and cell imaging. Finally, brief summary and future outlooks of this field will be presented.

High-Entropy Oxide for Highly Efficient Luminol-Dissolved Oxygen Electrochemiluminescence and Biosensing Applications

The luminol-dissolved O₂ (DO) electrochemiluminescence (ECL) sensing system has recently gained growing interest; however, the drawback of the ultra-low ECL signal response greatly hinders its potential quantitative applications. In this work, for the first time, we explored the use of high entropy oxide (HEO) comprising five metal ingredients (Ni, Co, Cr, Cu, and Fe), to accelerate the reduction reaction of DO into reactive oxygen species (ROS) for boosting the ECL performance of the luminol-DO system. Benefiting from the existing abundant oxygen vacancies induced by the unique crystal structure of the HEO, DO could be efficiently converted into ROS, thus significantly boosting the performance of the corresponding ECL sensor (with an ∼240-fold signal enhancement in this study). As a proof of concept, under optimal conditions, the developed HEO-involved luminol-DO ECL sensing system was successfully applied for efficient biosensing of dopamine and alkaline phosphatase with a fine linear range from 1 pM to 10 nM and from 0.01 to 100 U/L as well as a low limit of detection of 5.2 pM and 0.008 U/L, respectively.

Integrating potential-resolved electrochemiluminescence with molecularly imprinting immunoassay for simultaneous detection of dual acute myocardial infarction markers

A novel potential-resolved molecularly imprinted electrochemical luminescence (ECL) immunosensor has been developed for the first time for the dual sensitive detection of markers of acute myocardial infarction (AMI): cardiac troponin I (cTnI) and myoglobin (Mb). In this work, cost-effective and robust molecularly imprinted polymer (MIP) as biomimetic antibody was used to construct the immunosensors through electropolymerization and elution to form polydopamine (PDA)-MIP modified electrode. In the presence of AMI biomarkers, two ECL probes including Ru(bpy)₃²⁺@ MOCs and MoS₂ QDs functionalized by cTnI antibody and Mb aptamer could be specifically captured respectively. And two potential distinct ECL signals will be generated in one potential scan. The intensity of ECL reflects the concentrations of cTnI and Mb. The two ECL probes were characterized with field emission scanning electron microscopy, X-ray diffraction, FT-IR spectrum and UV-Vis diffuse reflectance spectroscopy. The prepared sensor exhibited a wide linear range (0.05-10⁴ ng/mL) and a low detection limit (0.0184 ng/mL for cTnI and 0.0492 ng/mL for Mb). Additionally, the MIP-ECL sensor displayed excellent anti-interference, sensitivity and stability to detect cTnI and Mb. Therefore, it will be conducive to accelerate more precise and credible early diagnosis for AMI.

A spatially resolved ratiometric electrochemiluminescence immunosensor for myoglobin detection using Au@Ag2S as signal amplification tags

A spatially resolved ratiometric ECL immunosensor for myoglobin detection was developed via resonance energy transfer for signal amplification.

Two-Dimensional-Plasmon-Boosted Iron Single-Atom Electrochemiluminescence for the Ultrasensitive Detection of Dopamine, Hemin, and Mercury

Single-atom catalysts (SACs) have recently been exploited for luminol-dissolved oxygen electrochemiluminescence (ECL); however, they still suffer from low sensitivity and narrow detection range for a real sample assay. In this work, we boost markedly the ECL response of the iron SAC (Fe-SAC)-based system, for the first time, by the excitation of two-dimensional plasmons derived from the Au@SiO₂ nanomembrane. The plausible mechanism of plasmon enhancement in the Fe-SAC ECL system has been discussed. The constructed Fe-SAC ECL system has been applied for the ECL detection of dopamine, hemin, and mercury (Hg²⁺), with pretty low limits of detection of 0.1, 0.7, and 0.13 nM and wider linear ranges of 0.001-1.0, 0.001-10, and 0.01-0.5 nM, respectively, under optimal conditions.

Liposome-assisted enzyme catalysis: toward signal amplification for sensitive split-type electrochemiluminescence immunoassay

Developing an efficient signal amplification strategy is very important to improve the sensitivity of bioanalysis. In this paper, a liposome-assisted enzyme catalysis signal amplification strategy was developed for electrochemiluminescence (ECL) immunoassay of prostate specific antigen (PSA) in a split-type mode. The sandwich immunoreaction occurred in a 96-well plate, and glucose oxidase (GOx) encapsulated and antibody-modified liposomes were used as labels. The ECL detection was carried out using a rGO-Au NP modified glassy carbon electrode (GCE). The large amount of generated H2O2, i.e. the coreactant of the luminol system, and the excellent catalytic behavior of rGO-Au NPs greatly boosted the ECL signal, resulting in the signal amplification. The developed ECL immunosensor for detecting PSA achieved a wider linear range from 1.0 × 10-13 to 1.0 × 10-8 g mL-1 and a detection limit of 1.7 × 10-14 g mL-1. The application of the proposed strategy was demonstrated by analyzing PSA in human serum samples with recoveries from 89.0% to 113.0%, and relative standard deviations (RSDs) were less than 6.6%. This work provides a new horizon to expand the application of liposomes for ECL bioanalysis.

Spatially-resolved dual-potential sandwich electrochemiluminescence immunosensor for the simultaneous determination of carbohydrate antigen 19-9 and carbohydrate antigen 24-2

A new electrochemiluminescence (ECL) immunosensor based on spatially-resolved dual-potential technology was designed for the simultaneous determination of carbohydrate antigen 19-9 (CA 19-9) and carbohydrate antigen 24-2 (CA 242). Luminol-AgNPs@ZIF-67 was used as the anodic probe, and Pt nanoparticle-functionalized graphitic carbon nitride nanosheets (g-C₃N₄@PtNPs) were used as the cathodic probe. Two spatially-resolved areas on the dual-disk glassy carbon electrode (DDGCE) were modified with a AuNPs film by electrodeposition to improve the conductivity of the sensing interface. By recording the ECL responses at two different excitation potentials, the linear range for CA 19-9 was determined to be 0.0001-10 U/mL, with a limit of detection of 31 μU/mL. The linear range for CA 242 was 0.0005-10 U/mL, with a limit of detection of 0.16 mU/mL. Moreover, the ECL immunosensor possessed high selectivity and stability and successfully detected CA 19-9 and CA 242 in real samples. This immunosensor provides a new platform for clinical immunoassays.

A ratiometric electrochemiluminescent cytosensor based on polyaniline hydrogel electrodes in spatially separated electrochemiluminescent systems

Here, we proposed a ratiometric electrochemiluminescent (ECL) strategy in spatially multiplied ECL systems. By the specific recognition of hyaluronic acid with proteoglycan CD44 and epidermal growth factor with epidermal growth factor receptor on the cell surface, the cells were labelled with potential-resolved ECL probes, namely Ru(bpy)₃²⁺ and g-C₃N₄, respectively. The as-proposed cytosensor provides a multichannel ECL protocol to improve the throughput, which may push the application of ECL for the cellular immunoanalysis.

A potential-resolved electrochemiluminescence resonance energy transfer strategy for the simultaneous detection of neuron-specific enolase and the cytokeratin 19 fragment

An electrochemiluminescence resonance energy transfer (ECL-RET) immunosensor was developed based on the potential-resolved technology for the simultaneous detection of neuron-specific enolase (NSE) and the cytokeratin 19 fragment (CYFRA21-1). The absorption spectrum of gold nanorods (AuNRs) perfectly overlapped with the ECL spectra of SnS2@Pt and Ru(bpy)32+/Zn-MOF, so they exhibited an excellent ECL-RET effect with high efficiency. Zn-MOF possesses a large surface area, which allows for the loading of Ru(bpy)32+. This results in a signal probe of Ru(bpy)32+/Zn-MOF/Ab1 showing a strong ECL emission. Simultaneously, owing to the excellent electronic conductivity of PtNPs, they can increase the electron transfer rate between S2O82- and tin disulfide nanoflowers (SnS2NFs). Hence, the ECL signal of SnS2NFs can be enhanced. Under the optimal conditions, the linear range for NSE is 0.2 pg mL-1-20 ng mL-1 with a detection limit of 79 fg mL-1. The linear range for CYFRA21-1 is 1.25 pg mL-1-12.5 ng mL-1 with a detection limit of 0.43 pg mL-1. The proposed immunosensor can be used for the sensitive simultaneous detection of NSE and CYFRA21-1 in human serum and has promise for clinical diagnostics.

Dual-Modular Aptasensor for Detection of Cardiac Troponin I Based on Mesoporous Silica Films by Electrochemiluminescence/Electrochemical Impedance Spectroscopy

A simple, dual-modular aptasensor for accurate determination of cardiac troponin I (cTnI), a sensitive biomarker of acute myocardial infarction, is reported. It has the parallel output of electrochemiluminescence (ECL) and electrochemical impedance spectroscopy (EIS) based on target-gated transportation of signal probes (luminol/H₂O₂ or Fe(CN)₆^3-/4-). The sensing capacity is originated from the amino-functionalized mouth margin of the nanochannels in a vertically oriented mesoporous silica film, which was in situ-grown on indium tin oxide-coated glass. With the linkage of glutaraldehyde to couple the aptamer as a trapper, it brings in the high specific target-gated response toward cTnI as decreased ECL or increased EIS. The concentration of cTnI is measurable by the ECL response within a wide linear range from 0.05 pg mL^-1 to 10 ng mL^-1, as well as the EIS response for a linear range between 0.05 pg mL^-1 and 1 ng mL^-1. Significantly, the self-verification of these two data from ECL and EIS validated each other with a satisfactory linear correlation (R² = 0.999), thereby realizing the more reliable and accurate quantification to avoid false results. The designed strategy is an effective method for detection of cTnI, which is of great potential to apply in clinical detection.

Surface-enhanced electrochemiluminescence combined with resonance energy transfer for sensitive carcinoembryonic antigen detection in exhaled breath condensates

The detection of biomarkers in exhaled breath condensates (EBCs) is regarded as a promising non-invasive diagnostic approach. However, the ultralow concentration of biomarkers in EBCs is a great challenge. Herein, a sensitive dual signal amplification strategy was developed based on surface-enhanced electrochemiluminescence (SEECL) combined with resonance energy transfer (RET). Gold nanoparticles-functionalized graphite-like carbon nitride nanohybrids (Au-g-C₃N₄ NHs) could be used as an energy transfer donor because of the good overlap between its emission peak and the absorption peak of tris(2,2'-bipyridine)ruthenium dichloride (Ru(bpy)₃Cl₂) at 460 nm. Gold-silicon dioxide core-shell nanoparticles doped with Ru(bpy)₃²⁺(Au@SiO₂-Ru) were employed as an energy transfer acceptor emitting at 620 nm. Moreover, the signals at 620 nm emitted by Ru (bpy)₃²⁺ were enhanced by 5 times, attributed to the localized surface plasmon resonance (LSPR) of gold nanoparticles (Au NPs). The detection of carcinoembryonic antigen (CEA) was performed by using two aptamers as the recognition unit; whereby aptamer 1 (Apt1) was modified on the surface of Au-g-C₃N₄ NHs, and aptamer 2 (Apt2) was banded on the surface of Au@SiO₂-Ru. In the presence of CEA, a sandwich structure was formed between Au-g-C₃N₄ NHs-Apt1-CEA and Apt2-Au@SiO₂-Ru, which resulted in an ultrasensitive detection of CEA. The proposed electrochemiluminescence sensor showed a wide linear relationship with the CEA concentration in the range from 1.0 pg mL^-1 to 5.0 ng mL^-1, with a limit of detection (LOD) of 0.3 pg mL^-1. Finally, the practicality of the proposed sensor was demonstrated to detect CEA in EBCs, and the obtained results were in good agreement with the enzyme-linked immunosorbent assay (ELISA) method.

Plasmon-enhanced quantum dots electrochemiluminescence aptasensor for selective and sensitive detection of cardiac troponin I

The development of highly sensitive electrochemiluminescence (ECL) immunosensors by using functional nanoparticles as signal amplifiers is a solution towards sensitive determination of many low concentration disease biomarkers. Herein, a sensitive aptamer-based, sandwich-type surface plasmon enhanced electrochemiluminescence (SPEECL) immunosensor was demonstrated for the detection of cardiac troponin I (cTnI), by means of aptamer conjugated CdS QDs and AuNPs as ECL luminophores and plasmon sources, respectively, in which Tro4 aptamer was used as a capture probe for cTnI and Tro6 aptamer as a detecting probe. The signal of the developed SPEECL system showed ~ 5-fold increment as compared to that of without AuNPs. Using this ECL platform for the detection of cTnI, a linear range and the limit of detection (LOD) were found to be 1 fg/mL - 10 ng/mL and 0.75 fg/mL, respectively.

Metal-organic frameworks-based sensitive electrochemiluminescence biosensing

Metal-organic frameworks (MOFs) as porous materials have attracted much attention in various fields such as gas storage, catalysis, separation, and nanomedical engineering. However, their applications in electrochemiluminescence (ECL) biosensing are limited due to the poor conductivity, lack of modification sites, low stability and specificity, and weak biocompatibility. Integrating the functional materials into MOF structures endows MOF composites with improved conductivity and stability and facilitates the design of ECL sensors with multifunctional MOFs, which are potentially advantageous over their individual components. This review summarizes the strategies for designing ECL-active MOF composites including using luminophore as a ligand, in situ encapsulation of luminophore within the framework, and post-synthetic modification. As-prepared MOF composites can serve as innovative emitters, luminophore carriers, electrode modification materials and co-reaction accelerators in ECL biosensors. The sensing applications of ECl-active MOF composites in the past five years are highlighted including immunoassays, genosensors, and small molecule detection. Finally, the prospects and challenges associated with MOF composites and their related materials for ECL biosensing are tentatively proposed.

Sensitive immunosensor based on high effective resonance energy transfer of lucigenin to the cathodic electrochemiluminescence of tris(bipyridine) Ru(II) complex

Electrochemiluminescence resonance energy transfer (ECL-RET) has been attracting much focus as an effective approach for great ECL enhancement. Here, we found that lucigenin (Luc) could serve as a new energy transfer donor and greatly improve the cathodic ECL of bis(2,2'-bipyridyl)(4'-methyl-[2,2']bipyridinyl-4-carboxylicacid) ruthenium(II) (Ru(Bpy)₂(Mcbpy)²⁺, acceptor). Then, both Luc and Ru(Bpy)₂(Mcbpy)²⁺ were largely co-immobilized onto the PdCu nanocrystals and polyethyleneimine (PEI) modified single-walled carbon nanohorns (SWCNHs-PdCuNCs-PEI) through π-π stacking and crosslinking reaction, respectively. By this way, the excellent electrocatalytic behavior and high loading capability for both Luc and Ru(Bpy)₂(Mcbpy)²⁺ of SWCNHs-PdCuNCs-PEI effectively facilitated the ECL reaction. Particularly, the co-immobilization strategy making the donor (Luc)/acceptor (Ru(Bpy)₂(Mcbpy)²⁺) pairs co-exist in the same nano-composite could obviously increase the ECL-RET efficiency by shortening the electron-transfer path and reducing energy loss, further significantly improving the ECL signal. Combining the obtained nano-composite (Luc-SWCNHs-PdCuNCs-PEI-Ru(Bpy)₂(Mcbpy)²⁺) with sandwiched immunoreaction, an ECL immunosensor was constructed for β2-microglobulin (β2-M) measurement. And as a result, it exhibited excellent performance in sensitivity, stability and selectivity. The establishment of the new effective donor/acceptor pairs for ECL-RET and the co-immobilization strategy of making those donor/acceptor pairs largely co-exist in the same nano-composite would greatly improve the ECL efficiency and motivate the wider application of ECL technology.

MnOx MFs as a coreaction accelerator for the construction of a novel ternary electrochemiluminescence system: ultrasensitive detection of microRNA

By using multivalent manganese oxides microflowers (MnOx MFs) as prominent a coreaction accelerator in luminol/dissolved oxygen system, and by combining these with DNA nanostructures for efficient immobilization of the electrochemiluminescence (ECL) quencher doxorubicin-ferrocenecarboxylic acid (Dox-FcCOOH), an ultrasensitive biosensing platform was constructed to conduct a microRNA assay in tumour cells.

Electrochemiluminescence biosensor for miRNA-21 based on toehold-mediated strand displacement amplification with Ru(phen)32+ loaded DNA nanoclews as signal tags

A novel electrochemiluminescence (ECL) biosensor was developed for high sensitive and selective detection of miRNA-21 based on the efficient and specific toehold-mediated strand displacement (TMSD) amplification with Ru(phen)₃²⁺ loaded DNA nanoclews (NCs-Ru(phen)₃²⁺) as signal tags. The stable DNA nanoclews, synthesized by a simple rolling circle amplification reaction, were employed to load with Ru(phen)₃²⁺ efficiently as ECL signal tags to amplify the signals. As for TMSD, the substrate strand (Sub) was initially hybridized with P1 and P2 to form DNA duplex structures with a toehold 1. miRNA-21 could hybridize with the toehold 1 and trigger the TMSD amplification with the help of assist strand, releasing lots of P1 stands from DNA duplex structures. The TMSD technique realized the converting and amplification of the single miRNA-21 input to lots of output DNA (namely P1) with good selectivity, simultaneously. Output P1 were designed to expand the stem-locked region of HP, which were immobilized on the Au electrodes firstly. Subsequently, the opened HP could hybridize with the Ru(phen)₃²⁺, capturing the ECL signal tags closed to the sensing surface. The ECL intensity of the system had a linear relationship with the logarithm of the miRNA-21 concentration in the range of 1.0 fM to 100 pM with a limit of detection of 0.65 fM. The strategy was further applied to detect miRNA-21 in complex samples, and the result was consistent with the qRT-PCR.

Electrochemiluminescence resonance energy transfer between methylene blue and Ru(bpy)32+-doped silica nanoparticles and its application in the “turn-on” detection of glucose

The ECL donor Ru(bpy)₃²⁺-doped silica nanoparticles and acceptor methylene blue were applied in the electrochemiluminescence resonance energy transfer-based detection of glucose.

BSA stabilized tetraphenylethylene nanocrystals as aggregation-induced enhanced electrochemiluminescence emitters for ultrasensitive microRNA assay

An ultrasensitive ECL biosensing platform was constructed based on BSA stabilized tetraphenylethylene nanocrystals to achieve microRNA detection in cancer cells.