Determination of sulfonamides in milk by capillary electrophoresis with PEG@MoS2 as a dispersive solid-phase extraction sorbent

Monolithic and hierarchically porous biochar/cellulose aerogel as adsorbent for microextraction in packed syringe towards trace sulfonamides in water samples prior to UPLC-MS/MS

In this study, biochars with desirable adsorption capacity were prepared by calcination of herbal medicine residue, and the obtained biochars were loaded on cellulose aerogel through a green synthesis method. The monolithic biochar/cellulose aerogel hybrid was packed in the syringe and used as adsorbent for microextraction in packed syringe (MEPS). After introducing cellulose aerogel as the support, the loss of powdered biochars was avoided, and the entire extraction process can be achieved through simple operation of filtration due to the macroporous structure of cellulose aerogel. Coupled with UPLC-MS/MS, the established method was successfully applied to determine trace level of sulfonamides (SAs) in water samples. Extraction parameters such as pH of sample solution, adsorbent type, sample volume, elution solvent type and elution solvent volume were studied. Under the optimized parameters (pH of sample solution:7, adsorbent type: biochar/cellulose aerogel, sample volume: 20 mL, elution solvent: 0.3 mL methanol, the number of aspiration and dispense of sample solution, washing solvent and elution solvent: 3), desirable linearity correlation coefficient (r) in the range of 0.9951-0.9972 was achieved. The limit of detection varied from 0.00407 to 0.0104 ng/mL, and recovery ranging from 65.3 % to 102.4 % was obtained. The proposed method was demonstrated to be sensitive, accurate and easily operative, providing a convenient protocol for sample pretreatment.

Determination of sulfonamide antibiotics by magnetic porous carbon solid-phase extraction coupled with capillary electrophoresis

Sulfonamide antibiotics (SAs) have been widely used as antibacterial drugs for the prevention and treatment of livestock and poultry diseases, but they seriously threaten human health because they can accumulate in humans. Therefore, it is highly important to develop methods for monitoring sulfonamide residues in aquaculture and food. In this research, based on the generation of porous carbon (PC) by the pyrolysis of sodium citrate, magnetic porous carbon (PC@Fe3O4) was synthesized by a solvothermal method and used as an adsorbent for the magnetic solid-phase extraction of SAs. The effects of the proportion of PC in PC@Fe3O4, adsorbent dosage, adsorption time, eluent type, extraction pH, salt concentration and eluent dosage on the extraction efficiency were systematically studied. The adsorption performance and behavior of PC@Fe3O4 on SAs were evaluated using adsorption kinetics and adsorption isotherms, and the adsorption mechanism was preliminarily discussed. Under optimal conditions, combined with capillary electrophoresis diode array detection, a sensitive detection method for SAs was developed. The proposed method can be used for the determination of six SAs in fishpond water and milk samples, with a linear range of 0.5-200 ng mL-1, detection limits of 0.24-0.34 ng mL-1, and spiked recoveries of 85.9-109.0 %.

Stabilizing Sulfur Sites in Tetraoxygen Tetrahedral Coordination Structure for Efficient Electrochemical Water Oxidation

Ion regulation strategy is regarded as a promising pathway for designing transition metal oxide-based electrocatalysts for oxygen evolution reaction (OER) with improved activity and stability. Precise anion conditioning can accurately change the anionic environment so that the acid radical ions (SO4 2- , PO3 2- , SeO4 2- , etc.), regardless of their state (inside the catalyst, on the catalyst surface, or in the electrolyte), can optimize the electronic structure of the cationic active site and further increase the catalytic activity. Herein, we report a new approach to encapsulate S atoms at the tetrahedral sites of the NaCl-type oxide NiO to form a tetraoxo-tetrahedral coordination structure (S-O4 ) inside the NiO (S-NiO -I). Density functional theory (DFT) calculations and operando vibrational spectroscopy proves that this kind of unique structure could achieve the S-O4 and Ni-S stable structure in S-NiO-I. Combining mass spectroscopy characterization, it could be confirmed that the S-O4 structure is the key factor for triggering the lattice oxygen exchange to participate in the OER process. This work demonstrates that the formation of tetraoxygen tetrahedral structure is a generalized key for boosting the OER performances of transition metal oxides.

Use of transition metal dichalcogenides (TMDs) in analytical sample preparation applications

Since the discovery of graphene, nano-sized two-dimensional (2D) transition metal dichalcogenides (TMDs) such as MoS2, MoSe2, MoTe2, NbS2, NbSe2, WS2, WSe2, TaS2 and TaSe2, which have been classified as next-generation nanomaterials resembling graphene (G) have complementary basic properties with those of graphene in terms of their practical applications. TMDs are attracting great attention due to their attractive physical, chemical and electronic properties. Despite being overshadowed by graphene in terms of frequency of use, TMDs have been used frequently in many areas in recent years instead of carbon-based materials such as graphene (G), graphene oxide (GO), carbon nanotubes (CNTs) and nanodiamonds (NDs). It is seen that the first and frequent uses of TMDs, which are classified as new generation materials, are in the fields of catalysis, electronic applications, hydrogen production processes and energy storage, but it has been used as an adsorbent in sample preparation techniques in recent years. Similar to graphene, layers of TMDs are held together by weak van der Waals interactions. The sandwiched layers of TMDs provide sufficient and effective interlayer spaces so that foreign molecules, ions and atoms can easily enter these spaces between the layers. Intermolecular interactions increase with the entry of different materials into these spaces, and thus, high activity, adsorption capacity and efficiency are obtained in adsorption-based analytical sample preparation methods. Although there are about 35 research articles using TMDs, which are classified as promising materials in analytical sample preparation techniques, no review studies have been found. This review, which was designed with this awareness, contains important informations on the properties of metal dichalcogenides, their production methods and their use in analytical sample preparation techniques.

ZnO and Au nanoparticles supported highly sensitive and selective electrochemical sensor based on molecularly imprinted polymer for sulfaguanidine and sulfamerazine detection

This study aimed to develop a molecularly imprinted polymer (MIP) sensor using electropolymerization of thiophene acetic acid monomer around template molecules, sulfaguanidine (SGN) and sulfamerazine (SMR), for selective and sensitive detection of both antibiotics. Au nanoparticles were then deposited on the modified electrode surface, and SGN and SMR were extracted from the resulting layer. Surface characterization, changes in the oxidation peak current of both analytes, and investigation of the electrochemical properties of the MIP sensor were examined using scanning electron microscopy, cyclic voltammetry, and differential pulse voltammetry. The developed MIP sensor with Au nanoparticles showed a detection limit of 0.030 µmol L-1 and 0.046 µmol L-1 for SGN and SMR, respectively, with excellent selectivity in the presence of interferents. The sensor was successfully used for SGN and SMR analysis in human fluids, including blood serum and urine, with excellent stability and reproducibility.

Carbon Black Integrated Polylactic Acid Electrodes Obtained by Fused Deposition Modeling: A Powerful Tool for Sensing of Sulfanilamide Residues in Honey Samples

Sulfanilamide (SFL) is used to prevent infections in honeybees. However, many regulatory agencies prohibit or establish maximum levels of SFL residues in honey samples. Hence, we developed a low-cost and portable electrochemical method for SFL detection using a disposable device produced through 3D printing technology. In the proposed approach, the working electrode was printed using a conductive filament based on carbon black and polylactic acid and it was associated with square wave voltammetry (SWV). Under optimized SWV parameters, linear concentration ranges (1-10 μmol L^-1 and 12.5-35.0 μmol L^-1), a detection limit of 0.26 μmol L^-1 (0.05 mg L^-1), and suitable RSD values (2.4% for inter-electrode; n = 3) were achieved. The developed method was selective in relation to other antibiotics applied in honey samples, requiring only dilution in the electrolyte. The recovery values (85-120%) obtained by SWV were statistically similar (95% confidence level) to those obtained by HPLC, attesting to the accuracy of the analysis and the absence of matrix interference.

Molecular Imprinted ZnS Quantum Dots-Based Sensor for Selective Sulfanilamide Detection

Combining molecular imprinted polymers and water-soluble manganese-doped zinc sulfide quantum dots (Mn2+: ZnS QDs), a new molecule imprinted polymers-based fluorescence sensor was designed. The molecule imprinted quantum dots (MIP@QDs) were constructed by coating molecular imprinted polymers layer on the surface of ZnS: Mn2+ QDs using the surface molecular imprinting technology. The developed MIP@QDs-based sensor was used for rapid and selective fluorescence sensing of sulfanilamide in water samples. The binding experiments showed that the MIP@QDs has rapid fluorescent responses, which are highly selective of and sensitive to the detection of sulfanilamide. The respond time of the MIP@QDs was 5 min, and the imprinting factor was 14.8. Under optimal conditions, the developed MIP@QDs-based sensor shows a good linearity (R2 = 0.9916) over a sulfanilamide concentration range from 2.90 × 10-8 to 2.90 × 10-6 mol L-1, with a detection limit of 3.23 × 10-9 mol L-1. Furthermore, the proposed MIP@QDs-based sensor was applied to the determination of sulfanilamide in real samples, with recoveries of 96.80%-104.33%, exhibiting good recyclability and stability. Experimental results showed that the prepared MIP@QDs has the potential to serve as a selective and sensitive sensor for the fluorescence sensing of sulfonamides in water samples.

Shining Light on Anion-Mixed Nanocatalysts for Efficient Water Electrolysis: Fundamentals, Progress, and Perspectives

This review introduces recent advances of various anion-mixed transition metal compounds (e.g., nitrides, halides, phosphides, chalcogenides, (oxy)hydroxides, and borides) for efficient water electrolysis applications in detail. The challenges and future perspectives are proposed and analyzed for the anion-mixed water dissociation catalysts, including polyanion-mixed and metal-free catalyst, progressive synthesis strategies, advanced in situ characterizations, and atomic level structure-activity relationship. Hydrogen with high energy density and zero carbon emission is widely acknowledged as the most promising candidate toward world's carbon neutrality and future sustainable eco-society. Water-splitting is a constructive technology for unpolluted and high-purity H₂ production, and a series of non-precious electrocatalysts have been developed over the past decade. To further improve the catalytic activities, metal doping is always adopted to modulate the 3d-electronic configuration and electron-donating/accepting (e-DA) properties, while for anion doping, the electronegativity variations among different non-metal elements would also bring some potential in the modulations of e-DA and metal valence for tuning the performances. In this review, we summarize the recent developments of the many different anion-mixed transition metal compounds (e.g., nitrides, halides, phosphides, chalcogenides, oxyhydroxides, and borides/borates) for efficient water electrolysis applications. First, we have introduced the general information of water-splitting and the description of anion-mixed electrocatalysts and highlighted their complementary functions of mixed anions. Furthermore, some latest advances of anion-mixed compounds are also categorized for hydrogen and oxygen evolution electrocatalysis. The rationales behind their enhanced electrochemical performances are discussed. Last but not least, the challenges and future perspectives are briefly proposed for the anion-mixed water dissociation catalysts.

Simultaneous preconcentration and determination of sulfonamide antibiotics in milk and yoghurt by dynamic pH junction focusing coupled with capillary electrophoresis

A dynamic pH junction was used in capillary electrophoresis (CE-DAD) to on-line preconcentrate, separate, and determine trace amounts of sulfonamide antibiotics (SAs) in milk and yoghurt samples in this study. A sample matrix with 0.15% acetic acid and 10% methanol (MeOH) at a pH of 4.0, and a background electrolyte (BGE) that contained 35 mM sodium citrate with 10% MeOH at a pH of 8.5, and an acidic barrage of 0.4% acetic acid with 10% MeOH at a pH of 2.5 were utilised to achieve a stacking effect for SAs through a dynamic pH junction. Under optimised conditions, the proposed preconcentration method showed good linearity (30-500 ng/mL, r² ≥ 0.9940), low limits of detection (LODs) of 4.1-6.3 ng/mL, and acceptable analytes recovery (81.2-106.9%) with relative standard deviations (RSDs) within 5.3-13.7 (n = 9). The limits of quantification (LOQs) were below the maximum residue limit approved by the European Union (EU) in this type of matrices. Sensitivity enhancement factors of up to 129 were reached with the optimised dynamic pH junction using CE with a diode array detector (DAD). The method was used to determine SAs in fresh milk, low-fat milk, full-cream milk, and yoghurt samples.

Technological Advancements for the Detection of Antibiotics in Food Products

Antibiotics, nowadays, are not only used for the treatment of human diseases but also used in animal and poultry farming to increase production. Overuse of antibiotics leads to their circulation in the food chain due to unmanaged discharge. These circulating antibiotics and their residues are a major cause of antimicrobial resistance (AMR), so comprehensive and multifaceted measures aligning with the One Health approach are crucial to curb the emergence and dissemination of antibiotic resistance through the food chain. Different chromatographic techniques and capillary electrophoresis (CE) are being widely used for the separation and detection of antibiotics and their residues from food samples. However, the matrix present in food samples interferes with the proper detection of the antibiotics, which are present in trace concentrations. This review is focused on the scientific literature published in the last decade devoted to the detection of antibiotics in food products. Various extraction methods are employed for the enrichment of antibiotics from a wide variety of food samples; however, solid-phase extraction (SPE) techniques are often used for the extraction of antibiotics from food products and biological samples. In addition, this review has scrutinized how changing instrumental composition, organization, and working parameters in the chromatography and CE can greatly impact the identification and quantification of antibiotic residues. This review also summarized recent advancements in other detection methods such as immunological assays, surface-enhanced Raman spectroscopy (SERS)-based assays, and biosensors which have emerged as rapid, sensitive, and selective tools for accurate detection and quantification of traces of antibiotics.

A novel fluorescent probe based on N, B, F co-doped carbon dots for highly selective and sensitive determination of sulfathiazole

The widespread occurrence of sulfathiazole (STZ) in the environment has raised concerns regarding the potential risks to ecosystem and human health. Thus, there is a need to develop facile and efficient methods for monitoring STZ. In this study, a novel fluorescent probe, based on N, B, F co-doped carbon dots (N, B, F-CDs), was developed for the highly sensitive and selective determination of STZ. The fluorescent N, B, F-CDs were prepared via a one-step hydrothermal method using malonate and 1-allyl-3-vinylimidazolium tetrafluoroborate ionic liquid as precursors. The obtained N, B, F-CDs exhibited excellent fluorescence response toward STZ due to the inner filter effect (IFE), which caused the fluorescence to be quenched. The fluorescent probe allowed the STZ concentration to be accurately determined with a low detection limit of 5.5 ng mL^-1 in two wide linear ranges of 0.008-10 μg mL^-1 and 10-45 μg mL^-1. The practicability of the fluorescent probe was further validated in river water, soil, milk, and egg samples, and the satisfactory spiked recoveries of STZ ranged from 96.1 to 101.6%. The proposed fluorescent probe based on N, B, F-CDs can be easily prepared and possess high selectivity and sensitivity, thereby displaying its tremendous potential for the identification and determination of STZ in the environment.

Determination of Sulfonamides in Milk by Cloud Point-Salting Out Extraction and Ultra-High-Performance Liquid Chromatography Tandem Mass Spectrometry

A method involving cloud point-salting out extraction (CPSOE) coupled with UHPLC-MS/MS was developed for the determination of eleven sulfonamides in milk. In this study, the type and concentration of the surfactant, de-emulsification condition, pH value, volume of n-butanol, equilibration temperature and time were optimized. For this developed method, the linear range of SAs was from 0.05 to 50 μg L-1, and the correlation coefficients were higher than 0.997. The average recoveries for SAs were from 61.32 to 91.67%, and the LOQs were less than 0.06 μg kg-1.

Recent Materials Developed for Dispersive Solid Phase Extraction

Solid phase extraction (SPE) is an analytical procedure developed with the purpose of separating a target analyte from a complex sample matrix prior to quantitative or qualitative determination. The purpose of such treatment is twofold: elimination of matrix constituents that could interfere with the detection process or even damage analytical equipment as well as enriching the analyte in the sample so that it is readily available for detection. Dispersive solid phase extraction (dSPE) is a recent development of the standard SPE technique that is attracting growing attention due to its remarkable simplicity, short extraction time and low requirement for solvent expenditure, accompanied by high effectiveness and wide applicability. This review aims to thoroughly survey recently conducted analytical studies focusing on methods utilizing novel, interesting nanomaterials as dSPE sorbents, as well as known materials that have been only recently successfully applied in dSPE techniques, and evaluate their performance and suitability based on comparison with previously reported analytical procedures.

A graphene oxide-molybdenum disulfide composite used as stationary phase for determination of sulfonamides in open-tubular capillary electrochromatography

A graphene oxide-molybdenum disulfide (GO-MoS₂) composite was synthesized and utilized as the highly efficient stationary phase of open-tubular capillary electrochromatography (OT-CEC). The characterization results indicated that GO-MoS₂ composite was successfully synthesized. The GO-MoS₂-coated capillary column was prepared by covalent immobilization method for the determination of seven sulfonamides. The baseline separation of seven sulfonamides was achieved by GO-MoS₂-coated capillary column. The linear range was 0.05-100 μg/mL for sulfisomidine, sulfathiazole, sulfamerazine, phthalylsulfathiazole and sulfacetamide, 0.1-100 μg/mL for sulfamonomethoxine and sulfachloropyridazine with a satisfactory correlation coefficients (R²) > 0.9994. This developed OT-CEC method was successfully applied to determinate of seven sulfonamides in environmental water and milk samples with good recoveries of 85.77% - 109.10% and 80.03% - 109.97%, respectively. These results indicated that GO-MoS₂-coated capillary column possessed good stability and repeatability.

A Two-Dimensional Affinity Capture and Separation Mini-Platform for the Isolation, Enrichment, and Quantification of Biomarkers and Its Potential Use for Liquid Biopsy

Biomarker detection for disease diagnosis, prognosis, and therapeutic response is becoming increasingly reliable and accessible. Particularly, the identification of circulating cell-free chemical and biochemical substances, cellular and subcellular entities, and extracellular vesicles has demonstrated promising applications in understanding the physiologic and pathologic conditions of an individual. Traditionally, tissue biopsy has been the gold standard for the diagnosis of many diseases, especially cancer. More recently, liquid biopsy for biomarker detection has emerged as a non-invasive or minimally invasive and less costly method for diagnosis of both cancerous and non-cancerous diseases, while also offering information on the progression or improvement of disease. Unfortunately, the standardization of analytical methods to isolate and quantify circulating cells and extracellular vesicles, as well as their extracted biochemical constituents, is still cumbersome, time-consuming, and expensive. To address these limitations, we have developed a prototype of a portable, miniaturized instrument that uses immunoaffinity capillary electrophoresis (IACE) to isolate, concentrate, and analyze cell-free biomarkers and/or tissue or cell extracts present in biological fluids. Isolation and concentration of analytes is accomplished through binding to one or more biorecognition affinity ligands immobilized to a solid support, while separation and analysis are achieved by high-resolution capillary electrophoresis (CE) coupled to one or more detectors. When compared to other existing methods, the process of this affinity capture, enrichment, release, and separation of one or a panel of biomarkers can be carried out on-line with the advantages of being rapid, automated, and cost-effective. Additionally, it has the potential to demonstrate high analytical sensitivity, specificity, and selectivity. As the potential of liquid biopsy grows, so too does the demand for technical advances. In this review, we therefore discuss applications and limitations of liquid biopsy and hope to introduce the idea that our affinity capture-separation device could be used as a form of point-of-care (POC) diagnostic technology to isolate, concentrate, and analyze circulating cells, extracellular vesicles, and viruses.

Trends in sensitive detection and rapid removal of sulfonamides: A review

Sulfonamides in environmental water, food, and feed are a major concern for both aquatic ecosystems and public health, because they may lead to the health risk of drug resistance. Thus, numerous sensitive detection and rapid removal methodologies have been established. This review summarizes the sample preparation techniques and instrumental methods used for sensitive detection of sulfonamides. Additionally, adsorption and photocatalysis for the rapid removal of sulfonamides are also discussed. This review provides a comprehensive perspective on future sulfonamide analyses that have good performance, and on the basic methods for the rapid removal of sulfonamides.

Nanostructured hybrid surface enhancement Raman scattering substrate for the rapid determination of sulfapyridine in milk samples

The fabrication of surface-enhanced Raman spectroscopy (SERS) substrates, which can offer the advantages of strong Raman signal enhancement with good reproducibility, is still a challenge for practical applications. In this work, a simple and reproducible SERS substrate combining the properties of multi-walled carbon nanotubes (MWCNTs) and gold nanoparticles (AuNPs), is proposed for the determination and quantification of sulfapyridine in milk samples with a concentration range of 10-100 ng mL^-1. The Raman signals of sulfapyridine is enhanced at factor of 4394. The procedure presented is capable of detecting and quantifying small quantities of sulfapyridine without implying any preconcentration step, just using an affordable and portable Raman spectrometer. The precision, in terms of repeatability and inter and intermediate precision, was lower than 8% in all cases.