Factors affecting the viscosity of sodium hypochlorite and their effect on irrigant flow

Can the addition of surfactants to NaOCl irrigation impact on the percentage of voids of root canal filling?

This study evaluated the impact of canal irrigation using surfactants associated to NaOCl on the percentage of voids of root canal filling through micro-computed tomographic (micro-CT) analysis. 27 mandibular mesial roots with Vertucci type II canal configuration with isthmus were selected and scanned in a micro-CT device. The specimens were assigned to three groups (n = 9), according to the irrigation solution during instrumentation: 2.5% NaOCl without additives (control), 2.5% NaOCl with 0.1% Benzalkonium Chloride and 2.5% NaOCl with 0.1% Tween 80. After obturation, the specimens were rescanned, and the percentage of voids were calculated. Data were analysed using one-way ANOVA with a significance level of 5%. The percentage of voids were similar among the groups (p > 0.05). None of the specimens showed completely voids-free areas. The addition of surfactants to NaOCl irrigation did not improve the quality of root canal filling of mandibular mesial root canals.

Traditional and Recent Root Canal Irrigation Methods and Their Effectiveness: A Review

According to contemporary dental standards, the primary goal of endodontic therapy is the chemo-mechanical cleaning of the complex root canal system. Watering root canals with approved solutions and activating them are essential parts of this operation. This review outlines various irrigant activation methods for root canal therapy. Specifically, a comparison among the methods of manual dynamic activation, sonics (subsonic, sonic, and ultrasonic), internal heating, and lasers, was conducted. The results in this work were gathered using Scopus, Web of Science, Google Scholar, and PubMed databases by searching the following keywords: sodium hypochlorite, cleaning, activation, and irrigation methods. The present work concluded that the use of irrigant activation has a greater benefit than its absence. Regardless, it is impossible to point to a single effective activation method.

Susceptibility of emetic and enterotoxigenic Bacillus cereus grown at high temperature to disinfectants

The prevalence of emetic strains in food products is rare; however, infection with these may be fatal to the vulnerable population. Bacterial control of the emetic Bacillus cereus strains is still unclear. This study aimed to assess the influence of high temperature on the disinfection of emetic and enterotoxigenic B. cereus. Emetic B. cereus strains survived up to 50 °C; the lag time and maximum growth rate were higher at 42 °C than those at 30 °C. Compared to enterotoxigenic B. cereus, all emetic food strains showed higher minimum inhibitory concentrations and minimum bactericidal concentrations for sodium hypochlorite and citric acid. The disinfectant susceptibility of the emetic B. cereus OS-05 strain incubated at a higher temperature did not increase and was maintained at the highest MBC value. In all emetic B. cereus strains, enterotoxin gene expression was upregulated at 42 °C and 45 °C. Increased ces gene expression was also found in emetic B. cereus strains GP-15 and OS-05, with upregulation of 128- and 820-fold at 42 °C. Thus, emetic B. cereus grown at high temperatures may resist common disinfectants of the food industry. The findings may help control B. cereus in food or the food processing industry.

Influence of access cavity design, sodium hypochlorite formulation and XP-endo Shaper usage on apical debris extrusion - A laboratory investigation

This study assessed the amount of apically extruded debris during root canal preparation using XP-endo shaper and the supplemental use of XP-endo finisher comparing the use of traditional endodontic access or conservative endodontic access cavities and liquid or gel-based formulations of 5.25% sodium hypochlorite or distilled water as supplemental agents. Maxillary first premolar teeth (N = 148) were randomly divided based on their access cavity design and sub-grouped according to the supplemental agent used. The amount of extruded debris was analysed based on the dry weight of the debris collected using a previously established laboratory methodology. Debris extrusion occurred in all groups. Overall, the traditional endodontic access cavity design was associated with more debris extrusion compared to the conservative type. The use of sodium hypochlorite solution showed higher debris extrusion than the gel, whilst distilled water had intermediate values.

Cleaning efficacy of EDDY versus ultrasonically-activated irrigation in root canals: a systematic review and meta-analysis

BACKGROUND

Ultrasonically-activated irrigation (UAI) is effective in root canal irrigation but may damage canal walls. EDDY is a sonic activation system with flexible working tips that cause no harm to dentinal walls. This review explores the intracanal cleaning efficacy of EDDY compared with UAI in vitro.

METHODS

The systematic review was registered in the PROSPERO database (CRD42021235826). A literature search was conducted in six electronic databases. In vitro studies that compared the removal of smear layer, debris, soft tissue or microbes in root canals between EDDY and UAI were included. Data extraction and quality assessment were performed. Meta-analyses were conducted on smear layer removal and debris elimination with the standardized mean difference (SMD). Heterogeneity was measured using the I² test and the Chi² test. The random-effect model was used when I² > 50%, or p < 0.1, otherwise the fixed-effect model was applied. The level of significance was set at p < 0.05.

RESULTS

19 articles were included in this systematic review and 7 articles were included in meta-analyses. Meta-analyses on smear layer removal showed unimportant differences between EDDY and UAI at any canal third (coronal [SMD = 0.08, 95% confidence interval (95%CI): -0.29 to 0.45; p = 0.44, I² = 0%]; middle [SMD = 0.02, 95% CI: -0.44 to 0.47; p = 0.94, I² = 0%]; apical [SMD = 0.01, 95%CI: -0.35 to 0.38; p = 0.70, I² = 0%]). Meta-analyses on debris removal evaluated by scanning electron microscope (coronal [SMD = 0.03, 95% CI: -0.41 to 0.46; p = 0.27, I² = 23%]; middle [SMD = -0.24, 95% CI: -0.83 to 0.35; p = 0.80, I² = 0%]; apical [SMD = 0.24, 95%CI: -0.20 to 0.67; p = 0.36, I² = 2%]) and micro-CT (SMD = 0.36, 95% CI: -0.67 to 1.40; p = 0.03, I² = 70%) both found insignificant differences. No meta-analysis was undertaken on soft-tissue removal and disinfection due to the various study designs, but the qualitative analyses implied that EDDY achieved similar performance to UAI in both aspects.

CONCLUSIONS

Limited evidence indicated that EDDY was comparable to UAI in removing smear layer, debris, soft tissue and microbes ex vivo. Considering UAI may damage canal walls, EDDY might be a substitute for UAI in irrigation activation. But more randomized clinical trials are required to explore the clinical extrapolation of the results in this review.

Physicochemical properties and penetration into dentinal tubules of calcium hypochlorite with surfactants

Abstract The aim was to assess the physicochemical properties and the penetration into dentinal tubules of calcium hypochlorite solution [Ca(OCl)2], with or without surfactants. The surfactants benzalkonium chloride, cetrimide, Tween 80 and Triton X-100 were mixed at different concentrations with sodium hypochlorite solution (NaOCl), Ca(OCl)2 and distilled water (control). Once the critical micellar concentration (CMC) of the surfactants in Ca(OCl)2 and NaOCl was determined, pH, free chlorine, surface tension and free calcium ions were evaluated. The penetration into dentinal tubules of NaOCl and Ca(OCl)2, with or without benzalkonium chloride and Triton X-100 [surfactants that promoted the lowest surface tension of Ca(OCl)2], was assessed using human premolars stained with crystal violet. The statistical tests were one-way ANOVA and Tukey’s post-test, Kruskal-Wallis and Dunn’s post-test, two-way ANOVA and Bonferroni’s post-test, and t-test; depending on the assay. The addition of surfactants reduced the surface tension of NaOCl and Ca(OCl)2, and did not alter the pH or the free available chlorine of either solution. The addition of all surfactants increased the availability of free calcium ions in Ca(OCl)2, especially benzalkonium chloride. Ca(OCl)2 exhibited lower penetration into dentinal tubules than NaOCl, and the addition of surfactants did not improve the penetration of Ca(OCl)2, but did increase the penetration of NaOCl. It can be concluded that the addition of surfactants to Ca(OCl)2 did not increase the penetration into dentinal tubules, but it did promote lower surface tension, without changing the pH or free available chlorine values, and higher availability of free calcium ions in Ca(OCl)2.

Influence of sodium hypochlorite concentration on cavitation effect and fluid dynamics induced by photon-induced photoacoustic streaming (PIPS): A visualization study

PURPOSE

The aim of the present study was to visualize and compare the cavitation effect and fluid dynamics induced by photon-induced photoacoustic streaming (PIPS) using sodium hypochlorite (NaOCl) with different concentrations as irrigant.

METHODS

Forty artificial root canals were prepared using MTWO Niti file up to size #25/.06. The canals were randomly divided into four groups (n = 10/group). High-speed camera was used to visualize and compare the cavitation effect induced by PIPS in the artificial root canals containing saline or NaOCl. Fluid velocity and Reynolds number of saline, 1%-, 2.5%- and 5.25% NaOCl irrigants induced by PIPS in the apical region were calculated using TEMA 2D software while the fluid motions were recorded.

RESULTS

Visualization profile revealed that NaOCl presented a stronger cavitation effect and fluid dynamics than saline during PIPS activation. In the apical region, 1% NaOCl group presented the highest average velocity of 3.868 m/s, followed by 2.5% NaOCl group (3.685 m/s), 5.25% NaOCl group (2.353 m/s) and saline group (1.268 m/s), corresponding to Reynolds number of 1653.173, 1572.196, 995.503 and 477.692. Statistically higher fluid velocity was calculated in 1% and 2.5% NaOCl groups compared to saline group, respectively (p < 0.05).

CONCLUSIONS

The application of NaOCl and its concentration significantly influence the cavitation effect and fluid dynamics during PIPS activation. 1% and 2.5% NaOCl groups presented a more violent fluid motion in the apical region when activated by PIPS.

Comparative Evaluation of the Penetration Depth into Dentinal Tubules of Three Endodontic Irrigants

This study aimed to examine the penetration depth into dentinal tubules of some chelating agents. The 17% EDTA and two preparations containing surfactants (Smear Clear, Bioakt Endo) were tested. Surface tension and liquid viscosity were measured using a Dynamic Contact Angle Analyzer and a Haake rotational rheometer. To measure the penetration depth inside dentinal tubules, thirty maxillary central incisors were selected from a pool of extracted human permanent teeth and allocated to three experimental groups (10 samples each), as well as were mechanically shaped and cleansed with 5.25% NaOCl, followed by each of the chelators being labeled with 0.1 wt % Rhodamine B according to final irrigation protocol established. The samples were embedded in an epoxy resin, after which 200 μm thick transverse sections were obtained at 2, 5, and 8 mm from the apex with a saw microtome. The specimens were then observed using a confocal laser microscope (CLSM) and the penetration of the labeled solution was measured in every third of each sample. Statistical analysis was performed using ANOVA or Kruskal-Wallis tests according to the distribution of data, evaluated with the Shapiro-Wilk normality test. Viscosity and surface tension tests have shown that BioAKT Endo has the lowest values compared to EDTA and Smear Clear. The medium penetration depth did not significantly differ among the three irrigants, while it increased considerably from the apical to the coronal level in all groups. Additionally, the maximum penetration depth increased significantly from the apical to coronal level, while among groups, BioAKT Endo showed the highest values at the apical and middle level compared to the other irrigants. No significant differences were observed among the three groups in medium and maximum penetration depths when the entire root was considered. New irrigants containing surfactants show reduced surface tension and, in one case (BioAKT Endo), viscosity. The lowering of the surface tension allows for better penetration of liquids into dentinal tubules than EDTA alone, thus improving the cleaning of the root canal system.

Conservative shaping combined with three-dimensional cleaning can be a powerful tool: Case series

Conservative endodontics has been introduced about a decade ago. Since then, it has been demonstrated that less canal preparations lead to more dentin preservation resulted in decreased stress on tooth structure, mainly in the coronal third of the root, and potentially a higher resistance to fracture. In addition, smaller and larger canal preparations were comparable with regard to the cleanliness of the root canal. The purpose of this case series was to report on the outcome of root canal treatments following a conservative canal preparation, followed by three-dimensional cleaning technique (intracanal heating and ultrasonic activation of NaOCl).

Effects of heat in the properties of NaOCl alone and mixed with etidronate and alkaline tetrasodium EDTA

AIM

To assess the free available chlorine concentration (FAC), organic tissue dissolution and smear layer removal capacity of sodium hypochlorite (NaOCl) alone and when mixtured with etidronate (HEDP) and tetrasodium EDTA (Na₄ EDTA), and heated to different temperatures.

METHODOLOGY

Mixtures at 1 : 1 ratio of 5% NaOCl with distilled water (considered NaOCl alone), 18% HEDP or 10% Na₄ EDTA were heated to 25 °C, 37 °C, 48 °C and 60 °C. The FAC in the mixtures was assessed at 5, 10, 20, 30, 60 and 120 min. Samples of bovine muscle tissue (n = 10) were prepared with similar size and weighed before and after 5, 10 and 15 min of immersion in the mixtures heated to the different temperatures to verify organic matter dissolution. The intergroup results were compared statistically using one-way analysis of variance (anova) and intragroup by two-way analysis of variance (anova), both followed by Tukey's multiple-comparison test (α < 0.01). Bovine dentine blocks (n = 10) were analysed by scanning electron microscopy before and after immersion in the mixtures, and the time taken to remove the smear layer from the surfaces of the samples was determined. The Friedman test was used to compare the scores of the same group (α < 0.01), and the Kruskal-Wallis test with Dunn's post hoc was used to compare the different groups (α < 0.01). Saline solution was used as a control in the experiments of tissue dissolution and smear layer removal, RESULTS: Heating NaOCl alone did not affect its FAC. The higher the temperature of the mixtures with the chelators, the lower the FAC. Organic tissue dissolution was improved by increases in temperature of NaOCl alone and its mixture with HEDP (P < 0.01); however, the mixture with Na₄ EDTA had no improvement (P > 0.01). Smear layer removal by NaOCl alone was enhanced by heating resulting in lower scores in some samples and became more rapid in the mixtures with the chelators. The saline solution did not promote tissue dissolution nor smear layer removal (P > 0.01).

CONCLUSION

In this laboratory study, heating NaOCl alone or when mixed with HEDP improved its capacity to dissolve organic matter and remove the smear layer. However, the mixture with HEDP required frequent refreshment to retain these effects when heated. Due to the acceleration in the reaction between the irrigants, very rapid reductions in the free available chlorine in the mixtures with Na₄ EDTA heated to the different temperatures occurred.

Evaluation of the penetration of CHX 2% on dentinal tubules using Conventional Irrigation, Sonic Irrigation (EDDY) and Passive Ultrasonic Irrigation (PUI) techniques: An in vitro study

Background

Various procedures and techniques have been developed to increase the effectiveness and penetration of irrigants into the dentinal tubules and anatomical anfractuosities. Objective: The purpose of this in vitro study was to compare the effect of different irrigation techniques such as conventional irrigation with a syringe, sonic activation irrigation with EDDY and Passive Ultrasonic Irrigation. All these on dentinal tubule penetration using Chlorhexidine.

Material and Methods

45 lower premolar teeth extracted for orthodontic reasons were used. These teeth were decoronated to a length of 18mm. This working length was achieved by inserting a size 15 K file into the root canal until it was observed in the ápex. Then the length was reduced to 1 mm. The instrumentation was performed with the Wave One Gold system up to a file # 45. Irrigated with 2mL of CHX between instruments. A final irrigation was performed using 5 mL of 17% EDTA with an E1 - Irrisonic insert for 30 seconds. Then, the root canal was irrigated with 5 mL of distilled water and dried with paper tips. The final irrigation of the 2% CHX with Rhodamine B was carried out with the different techniques of irrigation. Syringe irrigation with 5 mL, sonic irrigation and passive ultrasonic activation activated for 30 seconds in two stages. Axial cuts were made at 200 microns, the observation was done with stereomicroscope and image analysis in Image J software.

Results

Statistically significant differences were found only in the apical region, where the depth penetration in the PUI group was 76 µm, MI 48 µm and SI 41 µm, while in the penetration area, the PUI group was 99 µm2, MI 77 µm2 and finally SI 53 µm2.

Conclusions

The CHX was able to penetrate the dentinal tubules of three-thirds of the roots, for which the technique that showed the greatest penetration capacity was the ultrasonic activation.

Key words:Clorhexidine. Dentinal tubule. Dentinal penetration. Passive ultrasonic irrigation. Eddy. Manual irrigation.

The influence of the addition of surfactants to sodium hypochlorite on the removal of hard tissue debris

AIM

To evaluate the effect of the addition of surfactants to sodium hypochlorite (NaOCl) on the removal of accumulated hard tissue debris (AHTD), before and after final irrigation with 17% EDTA, from mesial canals of mandibular molars through microcomputed tomographic (micro-CT) analysis.

METHODOLOGY

Thirty moderately curved mandibular mesial roots with Vertucci type II canal configuration were selected and scanned in a micro-CT device at an isotropic resolution of 22.9 μm. The specimens were assigned to three groups (n = 10) with respect to the root length, degree of curvature of the mesial root, volume and 3D anatomy of the root canals according to the irrigating solution used during root canal preparation: 2.5% NaOCl and 0.1% Benzalkonium Chloride, 2.5% NaOCl and 0.1% Tween 80 and 2.5% NaOCl without additives. The root canals were instrumented up to Reciproc R25 instrument. Then, the specimens were scanned again after canal preparation and after final irrigation with 17% EDTA, and the registered data sets were examined to evaluate the percentage of AHTD. For comparison between the different groups before and after using 17% EDTA, the Kruskal-Wallis test was used with a significance level of 5%. For comparison between the same groups before and after using 17% EDTA, the Wilcoxon test was used with a significance level of 5%.

RESULTS

None of the irrigant solutions tested was able to completely eliminate hard tissue debris from mesial canals of mandibular molars. There were no significant differences in the percentage of AHTD amongst the different irrigation solutions (P > 0.05). Final irrigation with 17% EDTA significantly reduced the percentage of AHTD (P < 0.05), without differences amongst the groups (P > 0.05).

CONCLUSIONS

The addition of surfactants to NaOCl did not affect the removal of AHTD from mesial canals of extracted mandibular molars. Final irrigation with 17% EDTA significantly improved AHTD removal.

Influence of Different Types of Root Canal Irrigation Regimen on Resin-based Sealer Penetration and Pushout Bond Strength

Introduction

The main objective of root canal treatment is to eliminate the micro-organism from the root canal system and three-dimensional obturation. The proper cleaning and shaping can be accomplished only by using appropriate instruments and effective irrigants during the root canal treatment.

Aim

To evaluate the influence of three different final irrigation regimen on depth of penetration of root canal sealers and push-out bond strength of obturation material.

Materials and methods

Thirty-six extracted single-rooted mandibular premolar human teeth with straight canals were decoronated and instrumented according to groups. Group I: Root canals were irrigated with 3% sodium hypochlorite (NaOCl), then irradiated with 980 nm diode laser (n = 12), Group II: Root canals were irrigated with 3% NaOCl, followed by 17% ethylenediaminetetraacetic acid (EDTA) (n = 12), Group III: Root canals were irrigated with 3% NaOCl, followed by 10% citric acid (n = 12). In each sample, single cone obturation was done with gutta-percha using AH plus sealer incorporated with rhodamine B dye. After seven days coronal, middle and apical thin cross sections were made for evaluation of dentinal tubule sealer penetration depth and pushout bond strength using confocal laser scanning microscope (CLSM) and universal testing machine, respectively. Statistical analysis among the three groups was done by using Kruskal-Wallis and post hoc test.

Results

Mean tubular penetration depth between diode laser (136.57 ± 48 µm), EDTA (130.56 ± 53 µm) and citric acid (113.37 ± 34 µm; P < 0.05) showed statistically highly significant results. Pushout bond strength did not differ significantly between diode laser (1.21 ± 0.48 Mpa), EDTA (1.05 ± 0.45 Mpa) and citric acid (0.93 ± 0.44 Mpa; P > 0.05).

Conclusion

Mean tubular penetration depth of AH plus sealer was better in diode laser than in EDTA and citric acid. Average push-out bond strength of obturation material did not differ significantly between diode laser, EDTA and citric acid.

Mystery of the high chlorine consumption in disinfecting a chemically enhanced primary saline sewage

Stonecutters Island Sewage Treatment Works is one of the largest sewage treatment plants in the world and consists mainly of a chemically enhanced primary treatment (CEPT) unit and a disinfection unit. It has long been realized that most of the dosed chlorine (15 mg/L) is lost at the beginning part of the disinfection unit during disinfection of the CEPT effluent. Lab-scale tests were therefore conducted in this study to determine the causes. Because ferric chloride is used in CEPT, ferrous iron in the CEPT effluent (from the reduction of ferric iron) was initially thought to be the main chlorine consumer. However, the chlorine consumption by ferrous iron was found to be 1.2 mg/L at most. Suspended solids and sulfide also did not contribute significantly to the chlorine consumption. Batch tests were therefore conducted to evaluate the effects of mixing condition and chlorine stock solution concentration on the chlorine consumption. Less chlorine was consumed upon increased mixing. Using a high-concentration chlorine stock solution (25000 mg/L) resulted in a 3-times-higher chlorine consumption in the absence of mixing than using a low-concentration chlorine stock solution (2500 mg/L). By correlating the losses of ammonia and total nitrogen with the chlorine consumption, we hypothesized that the use of a high-concentration chlorine stock solution under poor mixing leads to a localized high ratio of chlorine to ammonia, resulting in breakpoint chlorination and an unusually excessive chlorine consumption. A novel apparatus was developed to quantify the nitrogen gas generated during chlorination of a simulated wastewater, and the mass balance of nitrogen-containing species (i.e., ammonia, nitrogen gas, nitrite and nitrate) during the chlorination was inspected. The good fit between the measured chlorine consumption and that back-calculated from nitrogen-containing species verified our hypothesis. Finally, it needs mentioning that the high chlorine consumption and the breakpoint chlorination may occur during chlorine disinfection of any sewage effluents with relatively high ammonia levels; thus it is suggested that either not-too-high concentrations of chlorine stock solutions or sufficient mixing should be applied during disinfection of the sewage effluents.

Anti-biofilm efficacy of root canal irrigants against in-situ Enterococcus faecalis biofilms in root canals, isthmuses and dentinal tubules

OBJECTIVE

To investigate the anti-biofilm efficacy of root canal irrigants in canal spaces, isthmi and dentinal tubules of root canals ex vivo.

METHODS

Fifty-one single-rooted premolars, each containing an isthmus, were instrumented, autoclaved and inoculated with Enterococcus faecalis for 4 weeks. One specimen was sectioned for bacteria-specific staining to confirm the presence of biofilms using light microscopiy. The remaining specimens were randomly divided to five groups: (1) 0.9% NaCl, (2) SilverSol/H₂O₂, (3) HYBENX, (4) QMix 2 in1, (5) 6% NaOCl. Bacterial sampling was performed before (S1) and after (S2) canal irrigation. Diluted bacteria suspension was cultured for 48 h for counting the colony forming units (CFU). Percentages of dead bacteria and biofilm thickness were evaluated by confocal laser scanning microscopy (CLSM). Metabolic activity, lactic acid and polysaccharide synthesis of E. faecalis derived from S2 samples were analysed.

RESULTS

The percentages of dead bacteria were significantly affected by the factor "irrigant" (p < 0.001) and the factor "location" (p = 0.017). The percentages of dead bacteria in the isthmi and canals were both in the ordor: NaCl < SilverSol/H₂O₂ < HYBENX < QMix 2 in1 < NaOCl (p < 0.05). Only 6% NaOCl disrupted biofilms and significantly reduced their thickness. The CFU, metabolic activity, polysaccharide and lactic acid production of E. faecalis were all reduced by the disinfecting solutions.

CONCLUSIONS

SilverSol/H₂O₂ and HYBENX were less adept than QMix 2 in1 at killing biofilm bacteria in root canals. None of these antibacterial irrigants were effective, compared with 6% NaOCl, in disrupting biofilms.

CLINICAL SIGNIFICANCE

There is advantage in using HYBENX or QMix 2 in1 to kill intratubular bacteria biofilms because of their capability in removing the inorganic component of the smear layer. SilverSol/H₂O₂ requires extra time to eradicate intratubular biofilms upon removal of the organic and inorganic components of the smear layer by other root canal irrigants.

Influence of Mixed Additives on the Physicochemical Properties of a 5.25% Sodium Hypochlorite Solution: An Unsupervised Multivariate Statistical Approach

INTRODUCTION

This article reports for the first time the effects of multiple additives (polyethylene glycol 400, Triton X-100, benzalkonium chloride, and ethyl formate) on the surface tension, pH, and viscosity of 5.25% sodium hypochlorite (NaOCl) irrigant solution. Advanced statistical approaches based on unsupervised multivariate analysis (cluster analysis and principal component analysis) were used to quantify the variability of the physicochemical properties of the modified NaOCl solution for the first time in dentistry.

METHODS

Solutions of 5.25% NaOCl were modified with multiple additives in various concentrations, physicochemical parameters were measured at 22°C and 37°C, and the results were statistically analyzed to group the solutions and reveal the effects of additives.

RESULTS

Cluster analysis and principal component analysis revealed that pH and surface tension were the significant parameters (P < .05) for grouping the modified solutions. Four principal components, accounting for 90.6% of the total variance, were associated with flow characteristics (37.3%) determined by polyethylene glycol; the wetting property (22.5% and 10.5%), which was dependent on cationic and nonionic surfactant; and the antimicrobial effect (20.3%) influenced by ethyl formate. Varimax rotation of the principal components showed that the cationic surfactant (benzalkonium chloride) had significantly decreased surface tension compared with the nonionic surfactant (Triton-X). Although ethyl formate was introduced as an odor modifier, it had a significant effect on pH decrease and the occurrence of effervescence with O₂ and hypochlorous acid release.

CONCLUSIONS

The statistical results revealed that the 5.25% NaOCl irrigant solution should be modified with a mixture of 0.1% benzalkonium chloride, 1% ethyl formate, and 7% polyethylene glycol for obtaining a low pH and low surface tension.

The effect of sodium hypochlorite concentration and irrigation needle extension on biofilm removal from a simulated root canal model

To investigate the effect of sodium hypochlorite concentration and needle extension on removal of Enterococcus faecalis biofilm, sixty root canal models were 3D printed. Biofilms were grown on the apical 3 mm of the canal for 10 days. Irrigation for 60s with 9 mL of either 5.25% or 2.5% NaOCl or water was performed using a needle inserted either 3 or 2 mm from the canal terminus and imaged using fluorescence microscopy and residual biofilm percentages were calculated using imaging software. The data were analysed using analysis of covariance and two-sample t-tests. A significance level of 0.05 was used throughout. Residual biofilm was less using 5.25% than with 2.5% NaOCl. Statistically significant biofilm removal was evident with the needle placed closer to the canal terminus. A greater reduction of available chlorine and pH was noted as the concentration increased. One-minute irrigation was not sufficient for complete biofilm removal.

Comparison of the Antimicrobial Efficacy of Octenidine Dihydrochloride and Chlorhexidine with and Without Passive Ultrasonic Irrigation - An Invitro Study

INTRODUCTION

Elimination of microorganisms from infected root canals is a complicated task. Numerous measures have been described to reduce the microbial load in the root canal system, including the use of various instrumentation techniques, irrigation regimens and intracanal medicaments. The drawbacks of few commonly used irrigants include toxic and harmful side effects, microbial resistance to antimicrobial agents and staining. Hence there is a need for alternative agents which are nontoxic, effective and safe.

AIM

To compare and evaluate antimicrobial effects of 2% Chlorhexidine (CHX) versus 0.1% Octenidine Dihydrochloride (OCT) as root canal irrigant with and without passive ultrasonic irrigation against Enterococcus faecalis (E. faecalis) in vitro and to evaluate the depth of penetration of irrigant solution into the dentinal tubules at the junction of middle and apical third.

MATERIALS AND METHODS

Forty eight freshly extracted, single rooted human mandibular premolars were decoronated and root specimen standardized to 14mm. Biofilm of E. faecalis (strain ATCC 29212) was grown for seven days and the specimens were divided into four groups (n=12) based on irrigation protocol : Group I- Conventional Syringe Irrigation (CSI) with 2% CHX, Group II- CSI + 0.1% OCT, Group III-Passive Ultrasonic Irrigation (PUI) + 2% CHX and Group IV- PUI+ 0.1% OCT. Dentin shavings were collected at two depths (200μm and 400μm) and total number of colony forming units were determined. The data were statistically analyzed using ANOVA, Scheffes multiple comparison of means and paired t-test (p<0.05).

RESULTS

Group III and IV (PUI) showed significant difference compared to Group I and II (CSI) both at 200μm and 400μm (p=0.000). For Group III and Group IV no significant differences were found at 200μm and 400μm (p=1.000 and 0.363 respectively), however significant difference was found between data at 200μm and 400μm for all the four groups (p=0.000).

CONCLUSION

Octenidine (0.1%) was more effective than 2% Chlorhexidine against E. faecalis both at 200μm and 400μm. Passive ultrasonic irrigation proved to enhance the antimicrobial action of the irrigants.

An in vivo assessment of the influence of needle gauges on endodontic irrigation flow rate

Aim:

The aim of this clinical study was to assess the influence of irrigation needle gauge on endodontic irrigation flow rates.

Settings and Design:

In vivo assessment.

Materials and Methods:

Five specialist endodontists performed intracanal irrigation procedures on 50 mesiobuccal canal of mandibular first molars using three different irrigation needle gauges. Data of time taken for irrigation was recorded by an irrigation testing system and analyzed using independent sample “T” test and one-way analysis of variance (ANOVA) test. The level of significance was set at P < 0.05.

Statistical Analysis Used:

The following tests were used for the statistical analysis: Independent sample “T” test, one-way ANOVA test, and post hoc multiple comparison was carried out using Tukey's honest significant difference (HSD) test using Statistical Package for the Social Sciences (SPSS) version 16 for Windows.

Results:

The average flow rate of 26 gauge was 0.27 mLs⁻¹, of 27 gauge was 0.19 mLs⁻¹, and of 30 gauge was 0.09 mls⁻¹. There was statistical significance among the gauges (P < 0.001). 26 gauge had highest flow rate when compared with other groups followed by 27 gauge and 30 gauge respectively. The operator variability for flow rate of three endodontic irrigation needle gauges (26 gauge, 27 gauge, and 30 gauge) was found to be not significant.

Conclusions:

Needle gauge has significant influence on endodontic irrigation flow rate.

Penetration of Sodium Hypochlorite Modified with Surfactants into Root Canal Dentin

Abstract The aim of this study was to evaluate the effect of concentration, exposure time and temperature of sodium hypochlorite (NaOCl) added with surfactants on its penetration into dentinal tubules. Sixty-five extracted human permanent maxillary anterior teeth with single canals were prepared by ProTaper SX hand-operated instruments. The teeth were then sectioned perpendicular to the long axis. The crowns and apical thirds of all the teeth were removed. The remaining roots were processed into 4-mm-long blocks and stained overnight in crystal violet. One hundred and thirty stained blocks were further split into halves and treated by nine different types of NaOCl-based solutions. Three solutions were added with surfactants (Hypoclean, H6, Chlor-Xtra) and the others were regular hypochlorites at increasing concentrations (1%, 2%, 4%, 5.25%, <6%, 6% NaOCl) from different brands. The dentin blocks were exposed to the solutions for 2, 5, and 20 min at 20 °C, 37 °C and 45 °C, respectively. The depth of NaOCl penetration was determined by bleaching of the stain and measured by light microscopy at 20 and 40. Statistical comparisons were made by using a generalized linear model with Bonferroni's post-hoc correction. The shortest penetration (81±6.6 μm) was obtained after incubation in 1% NaOCl for 2 min at 20 °C; the highest penetration (376.3±3.8 μm) was obtained with Chlor-Xtra for 20 min at 45 °C. Varying NaOCl concentration produced a minimal effect while temperature and exposure time had a significant direct relationship with NaOCl penetration into dentinal tubules, especially those with lowered surface tension. The exposure time and temperature of sodium hypochlorite as well as the addition of surfactants may influence the penetration depth of irrigants into dentinal tubules.

Influence of Temperature on the Antibacterial Activity of Sodium Hypochlorite

Abstract The aim of this study was to compare the antimicrobial activity of 5.25% NaOCl, Hypoclean and Chlor-Xtra at 20 °C and 45 °C in bovine root dentin. One-hundred-and-seventy dentin tubes prepared from bovine maxillary incisors were infected for 21 days with Enterococcus faecalis. The specimens were divided into the following groups: 1. 5.25% NaOCl 20 °C; 2. Hypoclean 20 °C; 3. Chlor-Xtra 20 °C; 4. 5.25% % NaOCl 45 °C; 5. Hypoclean 45 °C; 6. Chlor-Xtra 45 °C; 7. positive control; 8. negative control. Dentin chips were collected with round burs into Brain Heart Infusion (BHI) broth. After culturing, the number of colony-forming units (CFU) was counted. Statistical analyses were performed using descriptive statistics (mean, standard deviation, median), Shapiro-Wilk test, ANOVA and Tukey test. Significance level was set at p<0.05. In all experimental groups, CFU was minimum after treatment (day 0) and the obtained results were significantly different from each other at any period (p<0.05). After treatment, the Hypoclean and Chlor-Xtra showed the lowest numbers of CFU at 20 °C and 45 °C, whereas 5.25% NaOCl showed the highest number of CFU at both temperatures. In each group, the number of CFUs increased significantly with time (p<0.05). The antibacterial activity of Hypoclean and Chlor-Xtra at 45 °C were significantly greater than other tested solutions.

Viscosity of endodontic irrigants: Influence of temperature

BACKGROUND

The aim of this study was to assess the influence of temperature on the viscosity of different endodontic irrigants.

MATERIALS AND METHODS

The measurements of viscosity of 3% hydrogen peroxide, 0.9% sodium chloride, aqueous solution of 0.2% chlorhexidine (CHX) and 0.2% cetrimide, 5% sodium hypochlorite (NaOCl) and 17% ethylenediaminetetraacetic acid (EDTA) at different temperatures (22°C, 30°C, 40°C, 50°C and 60°C) were obtained using Mohr balance and Ostwald viscometer. The Shapiro-Wilk test and Mann-Whitney U-tests were used for the statistical analysis. (α = 0.05).

RESULTS

No significant differences were recorded at each temperature among 3% hydrogen peroxide, 0.9% sodium chloride and aqueous solution of 0.2% CHX and 0.2% cetrimide. 5% NaOCl and 17% EDTA showed the higher values. Viscosity statistically decreased with increasing temperature.

CONCLUSION

Within the limitations of this study, 5% NaOCl and 17% EDTA are significantly viscous at room temperature and their viscosity reduces with elevating temperature.

Evaluation of penetration depth of 2% chlorhexidine digluconate into root dentinal tubules using confocal laser scanning microscope

OBJECTIVES

This study evaluated the penetration depth of 2% chlorhexidine digluconate (CHX) into root dentinal tubules and the influence of passive ultrasonic irrigation (PUI) using a confocal laser scanning microscope (CLSM).

MATERIALS AND METHODS

Twenty freshly extracted anterior teeth were decoronated and instrumented using Mtwo rotary files up to size 40, 4% taper. The samples were randomly divided into two groups (n = 10), that is, conventional syringe irrigation (CSI) and PUI. CHX was mixed with Rhodamine B dye and was used as the final irrigant. The teeth were sectioned at coronal, middle and apical levels and viewed under CLSM to record the penetration depth of CHX. The data were statistically analyzed using Kruskal-Wallis and Mann-Whitney U tests.

RESULTS

The mean penetration depths of 2% CHX in coronal, middle and apical thirds were 138 µm, 80 µm and 44 µm in CSI group, respectively, whereas the mean penetration depths were 209 µm, 138 µm and 72 µm respectively in PUI group. Statistically significant difference was present between CSI group and PUI group at all three levels (p < 0.01 for coronal third and p < 0.001 for middle and apical thirds). On intragroup analysis, both groups showed statistically significant difference among three levels (p < 0.001).

CONCLUSIONS

Penetration depth of 2% CHX into root dentinal tubules is deeper in coronal third when compared to middle and apical third. PUI aided in deeper penetration of 2% CHX into dentinal tubules when compared to conventional syringe irrigation at all three levels.

Electrochemical impedance spectroscopy investigation on the clinical lifetime of ProTaper rotary file system

The main objective of the current paper is to show that electrochemical impedance spectroscopy (EIS) could be a method for evaluating and predicting of ProTaper rotary file system clinical lifespan. This particular aspect of everyday use of the endodontic files is of great importance in each dental practice and has profound clinical implications. The method used for quantification resides in the electrochemical impedance spectroscopy theory and has in its main focus the characteristics of the surface titanium oxide layer. This electrochemical technique has been adapted successfully to identify the quality of the Ni-Ti files oxide layer. The modification of this protective layer induces changes in corrosion behavior of the alloy modifying the impedance value of the file. In order to assess the method, 14 ProTaper sets utilized on different patients in a dental clinic have been submitted for testing using EIS. The information obtained in regard to the surface oxide layer has offered an indication of use and proves that the said layer evolves with each clinical application. The novelty of this research is related to an electrochemical technique successfully adapted for Ni-Ti file investigation and correlation with surface and clinical aspects.

Influence of temperature and concentration on the dynamic viscosity of sodium hypochlorite in comparison with 17% EDTA and 2% chlorhexidine gluconate: An in vitro study

Aims:

The aim of this study was to assess the influence of temperature and concentration on the dynamic viscosity of sodium hypochlorite in comparison with 17% EDTA and 2% chlorhexidine gluconate.

Settings and Design:

In vitro

Materials and Methods:

Dynamic viscosity measurements of sodium hypochlorite [NaOCl (5.25%, 2.6%, 1.25%)], EDTA (17%), and chlorhexidine gluconate [CHX, 2%] were measured using a rotational digital viscometer at room temperature (25°C). The influence of temperature (45°C, 60°C) and concentration (5.25%, 2.6%, and 1.25%) on the dynamic viscosity of NaOCl was also evaluated. The measurements were performed using a circulating water bath calibrated with a thermostat, and the dynamic viscosity measurements were noted in Centipoise (Cps).

Statistical Analysis Used:

The tests used for the statistical analysis were Kolmogorov-Smirnov and Shapiro Wilk tests, one-way ANOVA, and independent sample t-test.

Results:

Viscosity statistically increased with NaOCl concentration and decreased with increasing temperature. Amongst the tested NaOCl groups, 5.25% NaOCl at room temperature was significantly the most viscous (μ =1.5300 Cps) while 1.25% NaOCl at 60°C was significantly the least viscous (μ =1.1800 Cps).

Conclusions:

5.25% NaOCl and 17% EDTA are significantly viscous at room temperature. Elevating the temperature of 1.25% NaOCl to 60°C significantly reduces the viscosity of the NaOCl.