Single-site Pt-doped RuO2 hollow nanospheres with interstitial C for high-performance acidic overall water splitting

Simple and Scalable Introduction of Single-Atom Mn on RuO2 Electrocatalysts for Oxygen Evolution Reaction with Long-Term Activity and Stability

Electrochemical oxygen evolution reaction (OER) is the bottleneck for realizing renewable powered green hydrogen production through water splitting due to the challenges of electrode stability under harsh oxidative environments and electrolytes with extreme acidity and basicity. Here, we introduce a single-atom manganese-incorporated ruthenium oxide electrocatalyst via a facile impregnation approach for catalyzing the OER across a wide pH range, while solving the stability issues of RuO2. The modified catalyst maintains stability for over 1000 h, delivering a current density of 10 mA cm-2 at a 213 mV overpotential in acid (pH 0), 570 mV in potassium bicarbonate (pH 8.8), and 293 mV in alkaline media (pH 14), demonstrating exceptional durability under various conditions. When used as an anode for realistic water-splitting systems, Mn-modified RuO2 performs at 1000 mA cm-2 with a voltage of 1.69 V (Nafion 212 membrane) for proton-exchange membrane water electrolysis, and 1.84 V (UTP 220 diaphragm) for alkaline water electrolysis, exhibiting low degradation and verifying its substantial potential for practical applications.

Simple "Directional Trimming" Strategy Engineered Platinum Atomic Clusters with Controllable Coordination Numbers for Efficient Hydrogen Evolution

The coordination number (CN) in atomic cluster (AC) catalysts endows their catalytic performance with flexible tunability. However, the quantitative relationship between the CN and catalytic activity of atomic cluster catalysts remains ambiguity. Herein, inspired by the gardeners trimming plants branches to obtain ornamental value shape, we propose a "directional trimming" strategy to obtain a series of AC catalysts with wide range of Cl CN and establish an inverted volcano curve to explain the effect of CN on hydrogen evolution reaction (HER). Moreover, Pt/CB-90 (moderate Cl CN of 3.7) exhibits the lowest overpotential of 22.94 mV at 10 mA cm-2 and outstanding mass activity (25 times to commercial Pt/C). This proposed synthesis strategy fully utilizes the precursor atoms and is widely applicable. The reaction liquid can be reused up to 20 times to obtain 1130 mg catalysts without introducing any other chemicals. Additionally, theoretical calculations highlight the appropriate Cl CN benefits the HER on Pt2 ACs. This fundamental understanding of the role of CN in catalytic activity offers valuable guidance to promote performance in various catalytic reactions.

Orbital-level band gap engineering of RuO2 for enhanced acidic water oxidation

Developing efficient and stable oxygen evolution reaction electrocatalysts under acidic conditions is crucial for advancing proton-exchange membrane water electrolysers commercialization. Here, we develop a representative strategy through p-orbital atoms (N, P, S, Se) doping in RuO2 to precisely regulate the lattice oxygen-mediated mechanism-oxygen vacancy site mechanism pathway. In situ and ex situ measurements along with theoretical calculations demonstrate that Se doping dynamically adjusts the band gap between the Ru-eg and O-p orbitals during the oxygen evolution reaction process. This modulation accelerates electron diffusion to the external circuit, promotes the lattice oxygen-mediated process, and enhances catalytic activity. Additionally, it facilitates electron feedback and stabilizes oxygen vacancies, thereby promoting the oxygen vacancy site mechanism process and enhancing catalytic stability. The resulting Se-RuOx catalyst achieves efficient proton-exchange membrane water electrolysers performance under industrial conditions with a minimal charge overpotential of 1.67 V to achieve a current density of 1 A cm-2 and maintain long-term cyclability for over 1000 h. This work presents a unique method for guiding the future development of high-performance metal oxide catalysts.

Engineering high-density microcrystalline boundary with V-doped RuO2 for high-performance oxygen evolution in acid

Designing efficient acidic oxygen evolution catalysts for proton exchange membrane water electrolyzers is challenging due to a trade-off between activity and stability. In this work, we construct high-density microcrystalline grain boundaries (GBs) with V-dopant in RuO2 matrix (GB-V-RuO2). Our theoretical and experimental results indicate this is a highly active and acid-resistant OER catalyst. Specifically, the GB-V-RuO2 requires low overpotentials of 159, 222, and 300 mV to reach 10, 100, and 1500 mA cm-2geo in 0.5 M H2SO4, respectively. Operando EIS, ATR-SEIRAS FTIR and DEMS measurements reveal the importance of GBs in stabilizing lattice oxygen and thus inhibiting the lattice oxygen mediated OER pathway. As a result, the adsorbate evolution mechanism pathway becomes dominant, even at high current densities. Density functional theory analyses confirm that GBs can stabilize V dopant and that the synergy between them modulates the electronic structure of RuO2, thus optimizing the adsorption of OER intermediate species and enhancing electrocatalyst stability. Our work demonstrates a rational strategy for overcoming the traditional activity/stability dilemma, offering good prospects of developing high-performance acidic OER catalysts.

Modulating Adsorption Behavior by Single-site Pt on RuO2 for Efficient Electrosynthesis of Glycolic Acid from Plastic Wastes

Electrochemical upcycling of polyethylene terephthalate (PET) wastes into valuable glycolic acid (GA) is an ideal solution for resource utilization. However, simultaneously achieving high activity and selectivity remains challenging due to the over-oxidation and C-C cleavage during ethylene glycol (EG) oxidation in PET hydrolysate. Herein, we develop an atomically isolated Pt on RuO2 (Pt1/RuO2) catalyst composed of high-density Pt-Ru interfaces that ensure single-site adsorption of EG, enrich surface *OH coverage and weaken *CO-CH2OH intermediate adsorption, thereby synergistically promoting GA generation. Specifically, Pt1/RuO2 delivers a remarkable mass activity of 8.09 A/mgPt, as well as a high GA Faradaic efficiency (95.3 %) and selectivity (96.9 %). Under membrane electrode assembly conditions, Pt1/RuO2 realizes a stable electrolysis over 500 h at 6 A with a GA yield rate of 4.06 g h-1. In-depth theoretical and in situ spectroscopic investigations reveal the synergy between isolated Pt and oxophilic RuO2 plays a crucial role in high-efficiency EG-to-GA conversion. This study offers valuable insights for the rational design of advanced catalysts for GA synthesis from PET wastes via a single-site doped bimetallic strategy.

p-p Orbital Hybridization Stabilizing Lattice Oxygen in Two-Dimensional Amorphous RuOx for Efficient Acidic Oxygen Evolution

Developing efficient Ru-based catalysts is crucial in reducing reliance on costly Ir for the acidic oxygen evolution reaction (OER). However, these Ru-based catalysts face a fundamental stability challenge due to the highly reactive nature of lattice oxygen. In this work, we propose an effective strategy to stabilize lattice oxygen in 2D amorphous RuOx through p-p orbital hybridization by incorporating dopants such as Al, Ga, and In. Notably, Ga doping exhibits remarkable acidic OER performance, leading to a 137 mV reduction in overpotential at 10 mA cm-2 and a 125-fold improvement in stability compared to undoped RuOx. This also surpasses the performances of most reported Ru-based catalysts. In contrast, doping with other elements from the same period, such as Mn, Co, or Cu, shows negligible improvements in catalytic performance. In situ electrochemical spectroscopic analysis, couples with theoretical calculations, reveals that the p-p orbital hybridization in the Ga-O coordination within Ga-RuOx effectively reduces the reactivity of lattice oxygen, suppresses the overoxidation of Ru, and switches the reaction pathway from the lattice oxygen mechanism to the adsorbate evolution mechanism. This novel p-p orbital hybridization strategy holds great potential for the development of efficient and robust electrocatalysts for OER and beyond.

Visualization of the Key Proton Activities in Hydrogen Evolution Reaction by Electrochromic Catalyst

The electrocatalytic hydrogen evolution reaction (HER) is a promising route to produce sustainable hydrogen energy carrier for global carbon neutrality. The HER performance is largely determined by the overall proton activities, but the identification of such key proton activities in microscopic HER process is rather difficult. Herein, the study demonstrates a visualized HER concept by integrating the fundamental HER process with electrochromic technology on a well-designed Pt@WO3 platform in acidic electrolyte, where the overall proton activities in HER process can be rapidly discriminated by the color changes of Pt@WO3 electrochromic electrode. In contrast to bare WO3 counterpart, the Pt@WO3 electrochromic electrode displays a rather more positive potential of initial-coloration state and faster decoloration rate associated with significantly improved reaction kinetics of hydrogen intercalation and deintercalation within WO3 component. Correspondingly, the as-prepared Pt@WO3 catalyst electrode exhibits a remarkable HER activity with a lower onset-potential (45 mV, proton adsorption and accumulation) and smaller Tafel slope (50 mV dec-1, proton desorption), nearly 11.1- and 3.5-fold enhancement than those of bare WO3 counterpart. It is believed that the work in integrating the interesting visualization functionality into fundamental HER process may improve the readability of such microscopic electrocatalytic reaction and advance the exploration of more intelligent electrocatalysts.

Highly Distorted High-Entropy Alloy Aerogels for High-Efficiency Hydrogen Oxidation Reaction

The development of efficient electrocatalysts for alkaline hydrogen oxidation reaction (HOR) is essential for anion exchange membrane fuel cells and advancing the hydrogen economy. Herein, we demonstrated PtRuRhPdIr high-entropy alloy aerogels (HEAAs) with highly distorted structure as efficient HOR electrocatalysts and realized effective control of PtRu-based metallic aerogels (MAs) with elemental components ranging from two to seven. Specially, PtRuRhPdIr HEAAs on carbon (PtRuRhPdIr HEAAs/C) exhibit excellent HOR activity, with Pt group metal (PGM)-normalized mass activity (5.75 A mgPGM-1) at 50 mV and exchange current density normalized by electrochemical surface area (0.69 mA cm-2), approximately 16.9 and 4.1 times that of the commercial Pt/C (0.34 A mgPGM-1, 0.17 mA cm-2), respectively. The mechanism study shows that the highly distorted PtRuRhPdIr HEAAs provide abundant unsaturated sites for HOR, and the synergistic effect of multiple-active sites balances the adsorption of H* and *OH, boosting the HOR performance.

Recent Development of Ir- and Ru-Based Electrocatalysts for Acidic Oxygen Evolution Reaction

Proton exchange membrane (PEM) water electrolyzers are one type of the most promising technologies for efficient, nonpolluting and sustainable production of high-purity hydrogen. The anode catalysts account for a very large fraction of cost in PEM water electrolyzer and also determine the lifetime of the electrolyzer. To date, Ir- and Ru-based materials are types of promising catalysts for the acidic oxygen evolution reaction (OER), but they still face challenges of high cost or low stability. Hence, exploring low Ir and stable Ru-based electrocatalysts for acidic OER attracts extensive research interest in recent years. Owing to these great research efforts, significant developments have been achieved in this field. In this review, the developments in the field of Ir- and Ru-based electrocatalysts for acidic OER are comprehensively described. The possible OER mechanisms are first presented, followed by the introduction of the criteria for evaluation of the OER electrocatalysts. The development of Ir- and Ru-based OER electrocatalysts are then elucidated according to the strategies utilized to tune the catalytic performances. Lastly, possible future research in this burgeoning field is discussed.

Scalable and efficient electrochemical bromination of arenes with Faradaic efficiencies surpassing 90

Developing cost-effective and environmentally friendly approaches to synthesize brominated chemicals, which are important intermediates for the synthesis of various useful molecules such as pharmaceuticals, surfactants, pesticides, and biologically active heterocyclic compounds, is of great significance. Herein, we present a highly efficient electrochemical bromine evolution reaction over vacancy rich Co3O4 using cheap NaBr as the bromine source for the synthesis of valuable brominated fine chemicals and pharmaceuticals under ambient conditions. The introduction of oxygen vacancy onto Co3O4 can greatly enhance the activity and selectivity of bromine evolution reaction by optimizing Br* intermediate adsorption and desorption, enabling bromination of a series of bioactive molecules and pharmaceuticals at high yields.

Inhibiting Overoxidation of Dynamically Evolved RuO2 to Achieve a Win-Win in Activity-Stability for Acidic Water Electrolysis

Proton exchange membrane (PEM) water electrolysis offers an efficient route to large-scale green hydrogen production, in which the RuO2 catalyst exhibits superior activity but limited stability. Unveiling the atomic-scale structural evolution during operando reaction conditions is critical but remains a grand challenge for enhancing the durability of the RuO2 catalyst in the acidic oxygen evolution reaction (a-OER). This study proposes an adaptive machine learning workflow to elucidate the potential-dependent state-to-state global evolution of the RuO2(110) surface within a complex composition and configuration space, revealing the correlation between structural patterns and stability. We identify the active state with distorted RuO5 units that self-evolve at low potential, which exhibits minor Ru dissolution and an activity self-promotion phenomenon. However, this state exhibits a low potential resistance capacity (PRC) and evolves into inert RuO4 units at elevated potential. To enhance PRC and mitigate the overevolution of the active state, we explore the metal doping engineering and uncover an inverse volcano-type doping rule: the doped metal-oxygen bond strength should significantly differ from the Ru-O bond. This rule provides a theoretical framework for designing stable RuO2-based catalysts and clarifies current discrepancies regarding the roles of different metals in stabilizing RuO2. Applying this rule, we predict and confirm experimentally that Na can effectively stabilize RuO2 in its active state. The synthesized Na-RuO2 operates in a-OER for over 1800 h without any degradation and enables long-term durability in PEM electrolysis. This work enhances our understanding of the operando structural evolution of RuO2 and aids in designing durable catalysts for a-OER.

Recent achievements in noble metal-based oxide electrocatalysts for water splitting

The search for sustainable energy sources has accelerated the exploration of water decomposition as a clean H2 production method. Among the methods proposed, H2 production via water electrolysis has garnered considerable attention. However, the process of H2 production from water electrolysis is severely limited by the slow kinetics of the anodic oxygen evolution reaction and large intrinsic overpotentials at the anode; therefore, suitable catalysts need to be found to accelerate the reaction rate. Noble metal-based oxide electrocatalysts retain the advantages of abundant active sites, high electrical conductivity of noble metals, and low cost, which make them promising electrocatalysts; however, they suffer from the challenge of an imbalance between catalytic activity and stability. This review presents recent research progress in noble metals and their oxides as electrocatalysts. In this review, two half-reactions (the hydrogen evolution reaction and the oxygen evolution reaction) of water electrolysis are described. Recently reported methods for the synthesis of noble metal-based oxide electrocatalysts, improvement strategies, and sources of enhanced activity and stability for these types of catalysts are presented. Finally, the challenges and future perspectives in the field are summarised. This review is expected to help improve the understanding of noble metal-based oxide electrocatalysts.

Mn0.75Ru0.25O2 with Low Ru Concentration for Active and Durable Acidic Oxygen Evolution

Ruthenium has emerged as a promising alternative to iridium in water-splitting anodes. However, it becomes overoxidized and dissolves at industry-relevant working conditions. To enhance the activity and stability of electrocatalysts for oxygen evolution reaction, an isostructural rutile MnRu oxide with low Ru concentration (Mn0.75Ru0.25O2) is synthesized and an asymmetric Mn-O-Ru dual-site active center is developed. It exhibits 154 mV overpotential at 10 mA cm-2 and can operate stably at 200 mA cm-2 for 670 h with a degradation rate of 29 uV/h-1. A proton exchange membrane water electrolyzer achieves stable operation at 1 A cm-2 for 700 h with a degradation rate of 53 uV h-1. Structural analysis and isotopic labeling correlate the asymmetric nature of the Mn-O-Ru dual-site active center, which facilitates the oxygen evolution reaction along the radical coupling pathway, with the stabilization of the cations and the lattice oxygen in isostructural rutile Mn0.75Ru0.25O2.

Controllable Detachment of Organic Ligands on Ultrathin Amorphous Nanosheets Tailors the Electron-Aggregation for Accelerated pH-Universal Hydrogen Reaction

Tailoring the local environment of catalyst surface has emerged as an effective strategy to enhance the reaction kinetics involving multiple intermediates. For hydrogen evolution reactions (HER), the driving factors for hydrogen aggregation and migration which are poorly understood in depth affects the reaction kinetics especially over a wide pH range. Inspired by the selectivity of the catalyst surface microenvironment for intermediates, an interfacial electrocatalyst composed of Ru ultrafine nanocatalysts anchored onto monolayer amorphous (a-WCoNiO) nanosheets with electron-rich microenvironment induced by an organic oleylamine ligand is designed to realize high-performance pH-universal HER. This Ru/a-WCoNiO possesses impressively low overpotentials of -13, -14, and -14 mV at 10 mA cm-2 in 0.5 m H2SO4, 1 m KOH and 1 m PBS, respectively, ranking among the best HER catalysts reported to date. Benefiting from the electron-rich microenvironment, the Ru/a-WCoNiO exhibits record-high turnover frequency (TOF) and mass activity (MA), which is more than 47.9 times higher than that of commercial 20% Pt/C. Importantly, other precious metals are loaded on a-WCoNiO and enhancing their mass current density for pH-universal HER. It is believed that this developed approach of organic modifiers tailored local microenvironment has practical significance and advantages for designing other high-performance catalysts.

Creating Bridged-H* Bond Structure for Boosting Electrocatalytic Hydrogen Evolution via Phosphorus-Doped Iridium Nanosheets

Iridium (Ir) is recognized to have extremely high catalytic activity in the hydrogen evolution reaction (HER). However, there are still technical challenges in maximizing the utilization of Ir atoms in the catalytic reaction process through dimensional regulation strategies. Herein, an innovative strategy is utilized to fabricate porous phosphorus-doped iridium (P-Ir) with a 2D structure, specifically the reduction of 1T phase-IrO2 (1T-IrO2) nanosheets using phosphine gas. The optimized P-Ir achieves an overpotential of 17.2 mV (vs RHE without iR-correction) in 0.5 m H2SO4 during the HER process, outperforming benchmark Pt/C (27.0 mV) and most reported Ir-based electrocatalysts. During the long-term stability tests, P-Ir maintains stable operation for more than 100 h at both -10 and -100 mA cm-2, respectively. Moreover, the HER activity and transient potential scanning results of Ir-based phosphides prove that doping P atoms in the Ir lattice promotes the reaction kinetic rate and charge transport capacity during hydrogen evolution. Theoretical calculations reveal that P atoms doping weakens the adsorption energy of H intermediates (H*) by regulating the d-band center of the Ir sites. Simultaneously, the desorption process of H* is also facilitated by forming a special bridged-H* bond structure, eventually accelerating the HER kinetics.

Phase-Engineered Bi-RuO2 Single-Atom Alloy Oxide Boosting Oxygen Evolution Electrocatalysis in Proton Exchange Membrane Water Electrolyzer

Engineering nanomaterials at single-atomic sites can enable unprecedented catalytic properties for broad applications, yet it remains challenging to do so on RuO2-based electrocatalysts for proton exchange membrane water electrolyzer (PEMWE). Herein, the rational design and construction of Bi-RuO2 single-atom alloy oxide (SAAO) are presented to boost acidic oxygen evolution reaction (OER), via phase engineering a novel hexagonal close packed (hcp) RuBi single-atom alloy. This Bi-RuO2 SAAO electrocatalyst exhibits a low overpotential of 192 mV and superb stability over 650 h at 10 mA cm-2, enabling a practical PEMWE that needs only 1.59 V to reach 1.0 A cm-2 under industrial conditions. Operando differential electrochemical mass spectroscopy analysis, coupled with density functional theory studies, confirmed the adsorbate-evolving mechanism on Bi-RuO2 SAAO and that the incorporation of Bi1 improves the activity by electronic density optimization and the stability by hindering surface Ru demetallation. This work not only introduces a new strategy to fabricate high-performance electrocatalysts at atomic-level, but also demonstrates their potential use in industrial electrolyzers.

Modulating Electronic Correlations in Ruthenium Oxides for Highly Efficient Oxygen Evolution Reaction

Elucidating the electronic factors dominating the adsorption properties of transition-metal oxides is essential to construct highly efficient oxygen-evolving catalysts for hydrogen production by water splitting but remains a great challenge. Electron correlation from on-site Coulomb repulsion (U) among d-electrons is generally believed to significantly affect the electronic structure of these materials; however, it has long been neglected in studying their adsorption properties. Here, by choosing ruthenium oxide as a model system, we demonstrate the role of electron correlation on the electrocatalytic activity toward oxygen evolution reaction (OER). Our density functional theory plus U calculations on rutile RuO2 reveal that the electron correlation can tune the adsorption energies for oxygenated intermediate and optimize them after the metallic oxide being a Mott insulator upon increasing U. By regulating the RuO6 octahedral network, we constructed and synthesized a series of strongly correlated ruthenium oxides, where the Mott insulating ones indeed exhibit a superior OER performance to the metallic RuO2. Our work builds a bridge between the electrochemistry and Mott physics for transition-metal oxides, opening a new avenue for designing advanced catalysts.

Effectiveness of strain and dopants on breaking the activity-stability trade-off of RuO2 acidic oxygen evolution electrocatalysts

Ruthenium dioxide electrocatalysts for acidic oxygen evolution reaction suffer from mediocre activity and rather instability induced by high ruthenium-oxygen covalency. Here, the tensile strained strontium and tantalum codoped ruthenium dioxide nanocatalysts are synthesized via a molten salt-assisted quenching strategy. The tensile strained spacially elongates the ruthenium-oxygen bond and reduces covalency, thereby inhibiting the lattice oxygen participation and structural decomposition. The synergistic electronic modulations among strontium-tantalum-ruthenium groups both optimize deprotonation on oxygen sites and intermediates absorption on ruthenium sites, lowering the reaction energy barrier. Those result in a well-balanced activity-stability profile, confirmed by comprehensive experimental and theoretical analyses. Our strained electrode demonstrates an overpotential of 166 mV at 10 mA cm-2 in 0.5 M H2SO4 and an order of magnitude higher S-number, indicating comparable stability compared to bare catalyst. It exhibits negligible degradation rates within the long-term operation of single cell and PEM electrolyzer. This study elucidates the effectiveness of tensile strain and strategic doping in enhancing the activity and stability of ruthenium-based catalysts for acidic oxygen evolution reactions.

Breaking the Stability-Activity Trade-off of Oxygen Electrocatalyst by Gallium Bilateral-Regulation for High-Performance Zinc-Air Batteries

The rational design of metal oxide catalysts with enhanced oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) performance is crucial for the practical application of aqueous rechargeable zinc-air batteries (a-r-ZABs). Precisely regulating the electronic environment of metal-oxygen (M-O) active species is critical yet challenging for improving their activity and stability toward OER and ORR. Herein, we propose an atomic-level bilateral regulation strategy by introducing atomically dispersed Ga for continuously tuning the electronic environment of Ru-O and Mn-O in the Ga/MnRuO2 catalyst. The Ga/MnRuO2 catalyst breaks the stability-activity restriction, showing remarkable bifunctional performance with a low potential gap (ΔE) of 0.605 V and super durability with negligible performance degradation (300,000 ORR cycles or 30,000 OER cycles). The theoretical calculations revealed that the strong coupling electron interactions between Ga and Ru-O/Mn-O tuned the valence state distribution of the metal center, effectively modulating the adsorption behavior of *O/*OH, thus optimizing the reaction pathways and reducing the reaction barriers. The a-r-ZABs based on Ga/MnRuO2 catalysts exhibited excellent performance with a wide working temperature range of -20-60 °C and a long lifetime of 2308 hours (i.e., 13,848 cycles) under a current density of 5 mA cm-2 at -20 °C.

Dual Doping in Precious Metal Oxides: Accelerating Acidic Oxygen Evolution Reaction

Developing a highly active and stable catalyst for acidic oxygen evolution reactions (OERs), the key half-reaction for proton exchange membrane water electrolysis, has been one of the most cutting-edge topics in electrocatalysis. A dual-doping strategy optimizes the catalyst electronic environment, modifies the coordination environment, generates vacancies, and introduces strain effects through the synergistic effect of two elements to achieve high catalytic performance. In this review, we summarize the progress of dual doping in RuO2 or IrO2 for acidic OERs. The three main mechanisms of OERs are dicussed firstly, followed by a detailed examination of the development history of dual-doping catalysts, from experimentally driven dual-doping systems to machine learning (ML) and theoretical screening of dual-doping systems. Lastly, we provide a summary of the remaining challenges and future prospects, offering valuable insights into dual doping for acidic OERs.

High-Entropy Metal Interstitials Activate TiO2 for Robust Catalytic Oxidation

Substitution metal doping strategies are crucial for developing catalysts capable of activating O2, but the leaching of metal dopants has greatly hindered their potential for extensive oxidation reactions under mild conditions. Here, the study develops an entropy-increase strategy to synthesize high-entropy metal (Mg, Ca, Mn, Fe, and Co) interstitial functionalized anatase TiO2 (HE-TiO2) nanosheets, demonstrating remarkable degradation efficiency across a wide pH range and exceptional stability in a flow-by electro-catalytic reactor. Relative to that of pristine TiO2, the intense lattice distortion on the (001) plane, an average lattice expansion of 2% on the (100) plane, and decrease of second shell peak of X-ray absorption spectra serve as compelling evidence for the formation of metal interstitials in HE-TiO2. Theoretical analysis and in situ synchrotron radiation Fourier transform infrared studies reveal that the electron of metal interstitials can populate the subgap states within the host TiO2, enabling a moderate adsorption band for robust and efficient O2 activation. This study introduces a universal strategy for synthesizing a novel class of high-entropy materials with integrated metal interstitials in metal oxides, promising to enhance the stability and efficiency of O2 activation catalysts and broaden their potential applications.

Undoped ruthenium oxide as a stable catalyst for the acidic oxygen evolution reaction

Reducing green hydrogen production cost is critical for its widespread application. Proton-exchange-membrane water electrolyzers are among the most promising technologies, and significant research has been focused on developing more active, durable, and cost-effective catalysts to replace expensive iridium in the anode. Ruthenium oxide is a leading alternative while its stability is inadequate. While considerable progress has been made in designing doped Ru oxides and composites to improve stability, the uncertainty in true failure mechanism in acidic oxygen evolution reaction inhibits their further optimization. This study reveals that proton participation capability within Ru oxides is a critical factor contributing to their instability, which can induce catalyst pulverization and the collapse of the electrode structure. By restricting proton participation in the bulk phase and stabilizing the reaction interface, we demonstrate that the stability of Ru-oxide anodes can be notably improved, even under a high current density of 4 A cm‒2 for over 100 h. This work provides some insights into designing Ru oxide-based catalysts and anodes for practical water electrolyzer applications.

Integrating NiSe2-MoSe2 heterojunctions with N-doped porous carbon substrate architecture for an enhanced electrocatalytic water splitting device

The development of sustainable energy technologies relies on the exploitation of efficient and durable electrocatalysts for water splitting at high current densities. Our work presents a novel bifunctional catalyst, denoted as NM@NC/CC, which combines the benefits of NiSe2-MoSe2 heterojunctions with nitrogen-enriched porous carbon derived from metal-organic frameworks (MOFs). The integration of these components is designed to harness their combined advantages, which include enhanced electron transfer, improved mass and gas evolution dynamics, and an increased number of catalytically active sites. These features collectively optimize the energetics for both the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER). As a result, the catalyst facilitates rapid kinetics for the overall water-splitting process. The NM@NC/CC demonstrates low overpotentials, requiring only 91 mV for the HER and 280 mV for the OER to reach a current density of 10 mA cm-2. Even at higher current densities of 100 mA cm-2 for HER and 50 mA cm-2 for OER, the overpotentials are only 159 mV and 350 mV, respectively. Additionally, a two-electrode setup using this catalyst achieves a current density of 10 mA cm-2 with a minimal cell voltage of 1.56 V. The insights gained from this study will contribute to the advancement of electrocatalysts for energy conversion technologies.

Partially amorphous NiFe layered double hydroxides enabling highly-efficiency oxygen evolution reaction at high current density

Layered double hydroxide (LDH) serves as an innovative catalyst for water electrolysis, showcasing outstanding performance in the oxygen evolution reaction (OER) under alkaline conditions. However, it faces challenges due to its low electrical conductivity and limited accessibility to active sites. In this work, the flexibility advantages of disordered amorphous and ordered crystals in NiFe LDH were combined to improve OER performance and maintain long-term stability. This combination induces a variety of effects, including improving the intrinsic activity, changing the OER mechanism from adsorb evolution mechanism (AEM) to lattice oxygen mechanism (LOM), and promoting the reaction kinetics of the catalyst. Moreover, the porous structure of NiFe LDH can efficiently alleviate the issue of local acidic environment induced by prolonged OER reaction, satisfying the criteria for long-term stability. Therefore, the NiFe-2.0 LDH catalyst only requires an ultralow overpotential of 189 mV at a current density of 10 mA cm-2 with Tafel slope of 43 mV dec-1. More importantly, the catalyst not only displays excellent electrocatalytic activity with an overpotential of 289 mV but also represents an outstanding stability over 80 h at an ultra-high current density of 1 A cm-2. This study provides a promising strategy for optimizing the catalytic activity and stability of catalyst at ampere current density, which is expected to achieve commercial applications.

Atomic-level Ru-Ir mixing in rutile-type (RuIr)O2 for efficient and durable oxygen evolution catalysis

The success of proton exchange membrane water electrolysis (PEMWE) depends on active and robust electrocatalysts to facilitate oxygen evolution reaction (OER). Heteroatom-doped-RuOx has emerged as a promising electrocatalysts because heteroatoms suppress lattice oxygen participation in the OER, thereby preventing the destabilization of surface Ru and catalyst degradation. However, identifying suitable heteroatoms and achieving their atomic-scale coupling with Ru atoms are nontrivial tasks. Herein, to steer the reaction pathway away from the involvement of lattice oxygen, we integrate OER-active Ir atoms into the RuO2 matrix, which maximizes the synergy between stable Ru and active Ir centers, by leveraging the changeable growth behavior of Ru/Ir atoms on lattice parameter-modulated templates. In PEMWE, the resulting (RuIr)O2/C electrocatalysts demonstrate notable current density of 4.96 A cm-2 and mass activity of 19.84 A mgRu+Ir-1 at 2.0 V. In situ spectroscopic analysis and computational calculations highlight the importance of the synergistic coexistence of Ru/Ir-dual-OER-active sites for mitigating Ru dissolution via the optimization of the binding energy with oxygen intermediates and stabilization of Ru sites.

Tantalum-stabilized ruthenium oxide electrocatalysts for industrial water electrolysis

The iridium oxide (IrO2) catalyst for the oxygen evolution reaction used industrially (in proton exchange membrane water electrolyzers) is scarce and costly. Although ruthenium oxide (RuO2) is a promising alternative, its poor stability has hindered practical application. We used well-defined extended surface models to identify that RuO2 undergoes structure-dependent corrosion that causes Ru dissolution. Tantalum (Ta) doping effectively stabilized RuO2 against such corrosion and enhanced the intrinsic activity of RuO2. In an industrial demonstration, Ta-RuO2 electrocatalyst exhibited stability near that of IrO2 and had a performance decay rate of ~14 microvolts per hour in a 2800-hour test. At current densities of 1 ampere per square centimeter, it had an overpotential 330 millivolts less than that of IrO2.

Metal oxide plating for maximizing the performance of ruthenium(IV) oxide-catalyzed electrochemical oxygen evolution reaction

Hydrogen production by proton exchange membrane water electrolysis requires an anode with low overpotential for oxygen evolution reaction (OER) and robustness in acidic solution. While exploring new electrode materials to improve the performance and durability, optimizing the morphology of typical materials using new methods is a big challenge in materials science. RuO2 is one of the most active and stable electrocatalysts, but further improvement in its performance and cost reduction must be achieved for practical use. Herein, we present a novel technology, named "metal oxide plating", which can provide maximum performances with minimum amount. A uniform single-crystal RuO2 film with thickness of ∼2.5 nm was synthesized by a solvothermal-post heating method at an amount (x) of only 18 μg cm-2 (ST-RuO2(18)//TiO2 NWA). OER stably proceeds on ST-RuO2(18)//TiO2 NWA with ∼100% efficiency to provide a mass-specific activity (MSA) of 341 A gcat-1 at 1.50 V (vs. RHE), exceeding the values for most of the state-of-the-art RuO2 electrodes.

Efficient direct formic acid electrocatalysis enabled by rare earth-doped platinum-tellurium heterostructures

The lack of high-efficiency platinum (Pt)-based nanomaterials remains a formidable and exigent challenge in achieving high formic acid oxidation reaction (FAOR) and membrane electrode assembly (MEA) catalysis for direct formic acid fuel cell (DFAFC) technology. Herein, we report 16 Pt-based heterophase nanotrepang with rare earth (RE)-doped face-centered cubic Pt (fcc-Pt) and trigonal Pt-tellurium (t-PtTe2) configurations ((RE-Pt)-PtTe2 HPNT). Yttrium (Y) is identified as the optimal dopant, existing as single sites and clusters on the surface. The (Y-Pt)-PtTe2 HPNT/C demonstrates the superior mass and specific activities of 6.4 A mgPt-1 and 5.4 mA cm-2, outperforming commercial Pt/C by factors of 49.2 and 25.7, respectively. Additionally, it achieves a normalized MEA power density of 485.9 W gPt-1, tripling that of Pt/C. Density functional theory calculations further reveal that Y doping enhances HCOO* intermediate adsorption and suppresses CO intermediate formation, thereby promoting FAOR kinetics. This work highlights the role of RE metals in heterostructure regulation of Pt-based anodic nanomaterials for achieving the efficient direct formic acid electrocatalysis.

Boosting the durability of RuO2 via confinement effect for proton exchange membrane water electrolyzer

Ruthenium dioxide has attracted extensive attention as a promising catalyst for oxygen evolution reaction in acid. However, the over-oxidation of RuO2 into soluble H2RuO5 species results in a poor durability, which hinders the practical application of RuO2 in proton exchange membrane water electrolysis. Here, we report a confinement strategy by enriching a high local concentration of in-situ formed H2RuO5 species, which can effectively suppress the RuO2 degradation by shifting the redox equilibrium away from the RuO2 over-oxidation, greatly boosting its durability during acidic oxygen evolution. Therefore, the confined RuO2 catalyst can continuously operate at 10 mA cm-2 for over 400 h with negligible attenuation, and has a 14.8 times higher stability number than the unconfined RuO2 catalyst. An electrolyzer cell using the confined RuO2 catalyst as anode displays a notable durability of 300 h at 500 mA cm-2 and at 60 °C. This work demonstrates a promising design strategy for durable oxygen evolution reaction catalysts in acid via confinement engineering.

Fluorine-Induced Lattice Oxygen Participation in 2D Layered Double Hydroxide/MXene Hybrids for Efficient Oxygen Evolution

In oxygen evolution reaction (OER), the participation of lattice oxygen can break the limitation of adsorption evolution mechanism, but the activation of lattice oxygen remains a critical challenge. Herein, a surface fluorinated highly active 2D/2D FeNi layered double hydroxide/MXene (F-LDH/MX) is demonstrated, boosting OER with the enhanced lattice-oxygen-mediated path. The introduction of fluorine promotes the self-evolution of catalyst in an alkaline environment, even without an external current. It further accelerates the formation of active metal oxyhydroxides with abundant oxygen vacancies under the operating potential. The introduced oxygen vacancy activates the lattice oxygen, increasing the proportion of lattice oxygen mechanism in OER. Owing to the synergistic effects of the 2D/2D hierarchical structure and the modulated active surface, F-LDH/MX possesses excellent electrochemical performances, including a low overpotential of 251 mV at 10 mA cm-2, a low Tafel slope of 40.28 mV dec-1, and robust stability. The water electrolyzer system with F-LDH/MX as the anode offers the benchmark current density at a low cell voltage of 1.53 V, while the Zn-air battery with F-LDH/MX as the air electrode exhibits a higher power density of 75.43 mW cm-2. This study presents a promising strategy to design highly active electrocatalysts for energy conversion and storage.

Interfacial electronic modulation of NiCo decorated nano-flowered MoS2 on carbonized wood as a remarkable bifunctional electrocatalyst for boosting overall water splitting

The development of a cost-effective and efficient bifunctional electrode for overall water splitting holds significant importance in accelerating the sustainable advancement of hydrogen energy. The present study involved a bifunctional catalytic electrode was prepared by loading NiCo-modified 1T/2H MoS2 onto carbonized wood (NiCo-MoS2-CW) using the hydrothermal and electrodeposition techniques. The XPS analysis revealed that NiCo-modified MoS2 exhibited a weak electron characteristic, which facilitated the ionization of H2O and significantly enhanced the Volmer step. The XPS analysis unveiled that NiCo-modified MoS2 displayed a weak electron characteristic, thereby promoting the ionization of H2O and substantially augmenting the Volmer step. The electrocatalytic performance of the NiCo-MoS2-CW in 1.0 M KOH is remarkably impressive, exhibiting minimal overpotentials of only 64 mV (10 mA cm-2) and 216 mV (50 mA cm-2) for the hydrogen evolution reaction and oxygen evolution reaction, respectively. The NiCo-MoS2-CW || NiCo-MoS2-CW electrolytic cell can achieve a cell voltage of only 1.69 V to achieve a current density of 50 mA cm-2. Overall, this study proposes a potential approach to improve the catalytic efficiency of overall water splitting by modulating the interfacial electronic properties of MoS2.

Integrating Interactive Ir Atoms into Titanium Oxide Lattice for Proton Exchange Membrane Electrolysis

Iridium (Ir)-based oxide is the state-of-the-art electrocatalyst for acidic water oxidation, yet it is restricted to a few Ir-O octahedral packing modes with limited structural flexibility. Herein, the geometric structure diversification of Ir is achieved by integrating spatially correlated Ir atoms into the surface lattice of TiO2 and its booting effect on oxygen evolution reaction (OER) is investigated. Notably, the resultant i-Ir/TiO2 catalyst exhibits much higher electrocatalytic activity, with an overpotential of 240 mV at 10 mA cm-2 and excellent stability of 315 h at 100 mA cm-2 in acidic electrolyte. Both experimental and theoretical findings reveal that flexible Ir─O─Ir coordination with varied geometric structure plays a crucial role in enhancing OER activity, which optimize the intermediate adsorption by adjusting the d-band center of active Ir sites. Operando characterizations demonstrate that the interactive Ir─O─Ir units can suppress over-oxidation of Ir, effectively widening the stable region of Ir species during the catalytic process. The proton exchange membrane (PEM) electrolyzer, equipped with i-Ir/TiO2 as an anode, gives a low driving voltage of 1.63 V at 2 A cm-2 and maintains stable performance for over 440 h. This work presents a general strategy to eliminate the inherent geometric limitations of IrOx species, thereby inspiring further development of advanced catalyst designs.

Regulating the electronic structure of Pt SAs-Ni2P for enhanced hydrogen evolution reaction

The single atom catalysts (SACs) show immense promise as catalytic materials. By doping the single atoms (SAs) of precious metals onto substrates, the atomic utilization of these metals can be maximized, thereby reducing catalyst costs. The electronic structure of precious metal SAs is significantly influenced by compositions of doped substrates. Therefore, optimizing the electronic structure through appropriate doping of substrates can further enhance catalytic activity. Here, Pt single atoms (Pt SAs) are doped onto transition metal sulfide substrate NiS2 (Pt SAs-NiS2) and phosphide substrate Ni2P (Pt SAs-Ni2P) to design and prepare catalysts. Compared to the Pt SAs-NiS2 catalyst, the Pt SAs-Ni2P catalyst exhibits better hydrogen evolution catalytic performance and stability. Under 1 M KOH conditions, the hydrogen evolution mass activity current density of the Pt SAs-Ni2P catalyst reaches 0.225 A mgPt-1 at 50 mV, which is 33 times higher than that of commercial Pt/C catalysts. It requires only 44.9 mV to achieve a current density of 10 mA cm-2. In contrast, for the Pt SAs-NiS2 catalyst, the hydrogen evolution mass activity current density is 0.178 A mgPt-1, requiring 77.8 mV to achieve a current density of 10 mA cm-2. Theoretical calculations indicate that in Pt SAs-Ni2P, the interaction between Pt SAs and the Ni2P substrate causes the Pt d-band center to shift downward, enhancing the H2O desorption and providing optimal H binding sites. Additionally, the hollow octahedral morphology of Ni2P provides a larger surface area, exposing more reactive sites and improving reaction kinetics. This study presents an effective pathway for preparing high-performance hydrogen evolution electrocatalysts by selecting appropriate doped substrates to control the electronic structure of Pt SAs.

Insight Into Intermediate Behaviors and Design Strategies of Platinum Group Metal-Based Alkaline Hydrogen Oxidation Catalysts

Hydrogen oxidation reaction (HOR) can effectively convert the hydrogen energy through the hydrogen fuel cells, which plays an increasingly important role in the renewable hydrogen cycle. Nevertheless, when the electrolyte pH changes from acid to base, even with platinum group metal (PGM) catalysts, the HOR kinetics declines with several orders of magnitude. More critically, the pivotal role of reaction intermediates and interfacial environment during intermediate behaviors on alkaline HOR remains controversial. Therefore, exploring the exceptional PGM-based alkaline HOR electrocatalysts and identifying the reaction mechanism are indispensable for promoting the commercial development of hydrogen fuel cells. Consequently, the fundamental understanding of the HOR mechanism is first introduced, with emphases on the adsorption/desorption process of distinct reactive intermediates and the interfacial structure during catalytic process. Subsequently, with the guidance of reaction mechanism, the latest advances in the rational design of advanced PGM-based (Pt, Pd, Ir, Ru, Rh-based) alkaline HOR catalysts are discussed, focusing on the correlation between the intermediate behaviors and the electrocatalytic performance. Finally, given that the challenges standing in the development of the alkaline HOR, the prospect for the rational catalysts design and thorough mechanism investigation towards alkaline HOR are emphatically proposed.

Synergizing ruthenium oxide with bimetallic Co2CrO4 for highly efficient oxygen evolution reaction

Designing efficient and stable oxygen evolution reaction (OER) catalyst is the basis for the development of sustainable electrolytic water energy techniques. In this work, we presented a heterogeneous-structured electrocatalyst composed of bimetallic oxides-modified RuO2 nanosheets supported on nikel foam (Co2CrO4/RuO2) using a hybrid hydrothermal, ion-exchange and calcination method. The unique synergy and interfacial coupling between Co2CrO4/RuO2 heterostructures are favorable for optimizing the electronic configuration at this interface and strengthening the charge transport capacity, thus strengthening the catalytic activity of the Co2CrO4/RuO2 catalyst. The experimental data demonstrate that Cr leaching facilitates the rapid reconstruction of the catalyst into oxyhydroxides (CoOOH), which are acknowledged to be the real active species of OER. Theoretical calculations show that the Co2CrO4/RuO2 heterostructure increases the density state at the Fermi energy level and lowers the d-band center, thereby strengthening the catalytic activity. The synthesized Co2CrO4/RuO2 catalyst exhibited OER performance with an overpotential of 209 mV at 10 mA cm-2 and displayed a low Tafel slope of 78.2 mV dec-1, which outperforms most reported advanced alkaline OER catalysts. This work contributes to a new tactic for the design and development of ruthenium oxide/bimetallic oxides electrocatalysts.

Dynamic-Cycling Zinc Sites Promote Ruthenium Oxide for Sub-Ampere Electrochemical Water Oxidation

Although iridium-based electrocatalysts are commonly regarded as the sole stable operating acidic oxygen evolution reaction (OER) catalysts in proton-exchange membrane water electrolysis (PEMWE) devices, their exorbitant cost and scarcity severely restrict their widespread application. Herein, we introduce a promising alternative to iridium: zinc-doped ruthenium dioxide (TE-Zn/RuO2), which exhibits remarkable and enduring activity for acidic OER. In situ characterizations elucidate that the dynamic cycling of zinc dopants serves as both electron acceptors and donors, facilitating the activation of Ru sites at low overpotentials while thwarting peroxidation at high overpotentials, thus concurrently achieving heightened activity and robust stability. Additionally, the incorporation of zinc induces weakened Ru-O covalency, thereby stabling *OOH intermediates and instigating a sustained adsorbate evolution mechanism, dramatically stabilizing the RuO2 lattice. Importantly, the TE-Zn/RuO2 catalyst as an anode exhibits good stability over 300 h at a water-splitting current of 500 mA cm-2 in the PEMWE device, underscoring its considerable promise for practical applications.

Atomically Dispersed Mn-Doped Ru@RuO2 Core/Shell Nanostructure with High Acidic Water Oxidation Performance Arising from Multiple Synergies

The high overpotential and unsatisfactory stability of RuO2-based catalysts seriously hinder their application in acidic oxygen evolution reaction (OER). Herein, a Ru@RuO2 core/shell catalyst doped with atomically dispersed Mn species, denoted as Ru@Mn-RuO2, is reported, which is prepared by a facile one-pot method. Detailed structural characterizations confirm that Mn is homogeneously and atomically distributed in RuO2 shell, which causes lattice contraction of RuO2. The as-prepared Ru@Mn-RuO2 exhibits a very low overpotential of 190 mV at the current density of 10 mA cm-2 and an excellent stability of 360 h, far surpassing the control samples Ru@RuO2 without atomically dispersed Mn dopants and home-made RuO2 nanoparticles without metallic Ru core. With the further assistance of density functional theory calculations, the enhanced OER activity of Ru@Mn-RuO2 is attributed to multiple synergistic effects, including the MnOx-Ru (oxide shell) synergy, MnOx-Ru (metal core) synergy, and the Ru (core)-RuO2 (shell) synergy. Besides, the atomically dispersed Mn doping can increase the formation energy of soluble Ru cations, thus leading to the excellent stability of the Ru@Mn-RuO2 catalyst. This work shines light on the design of electrocatalysts with multiple synergistic effects towards efficient acid water splitting.

Phase Engineering-Mediated D-Band Center of Ru Sites Promote the Hydrogen Evolution Reaction Under Universal pH Condition

The rational design of pH-universal electrocatalyst with high-efficiency, low-cost and large current output suitable for industrial hydrogen evolution reaction (HER) is crucial for hydrogen production via water splitting. Herein, phase engineering of ruthenium (Ru) electrocatalyst comprised of metastable unconventional face-centered cubic (fcc) and conventional hexagonal close-packed (hcp) crystalline phase supported on nitrogen-doped carbon matrix (fcc/hcp-Ru/NC) is successfully synthesized through a facile pyrolysis approach. Fascinatingly, the fcc/hcp-Ru/NC displayed excellent electrocatalytic HER performance under a universal pH range. To deliver a current density of 10 mA cm-2, the fcc/hcp-Ru/NC required overpotentials of 16.8, 23.8 and 22.3 mV in 1 M KOH, 0.5 M H2SO4 and 1 M phosphate buffered solution (PBS), respectively. Even to drive an industrial-level current density of 500 and 1000 mA cm-2, the corresponding overpotentials are 189.8 and 284 mV in alkaline, 202 and 287 mV in acidic media, respectively. Experimental and theoretical calculation result unveiled that the charge migration from fcc-Ru to hcp-Ru induced by work function discrepancy within fcc/hcp-Ru/NC regulate the d-band center of Ru sites, which facilitated the water adsorption and dissociation, thus boosting the electrocatalytic HER performance. The present work paves the way for construction of novel and efficient electrocatalysts for energy conversion and storage.

Atomically engineered interfaces inducing bridging oxygen-mediated deprotonation for enhanced oxygen evolution in acidic conditions

The development of efficient and stable electrocatalysts for water oxidation in acidic media is vital for the commercialization of the proton exchange membrane electrolyzers. In this work, we successfully construct Ru-O-Ir atomic interfaces for acidic oxygen evolution reaction (OER). The catalysts achieve overpotentials as low as 167, 300, and 390 mV at 10, 500, and 1500 mA cm-2 in 0.5 M H2SO4, respectively, with the electrocatalyst showing robust stability for >1000 h of operation at 10 mA cm-2 and negligible degradation after 200,000 cyclic voltammetry cycles. Operando spectroelectrochemical measurements together with theoretical investigations reveal that the OER pathway over the Ru-O-Ir active site is near-optimal, where the bridging oxygen site of Ir-OBRI serves as the proton acceptor to accelerate proton transfer on an adjacent Ru centre, breaking the typical adsorption-dissociation linear scaling relationship on a single Ru site and thus enhancing OER activity. Here, we show that rational design of multiple active sites can break the activity/stability trade-off commonly encountered for OER catalysts, offering good approaches towards high-performance acidic OER catalysts.

Construction of directional electron transfer from Pt to MoO2-x in macroporous structure for efficient hydrogen oxidation

Hydrogen oxidation reaction (HOR) as the anode reaction in proton exchange membrane fuel cell, usually suffers from the high loading of platinum (Pt) and subsequent CO poisoning especially by using industrial crude hydrogen as fuel. In this work, we propose a directional electron transfer route from Pt to MoO2-x in the macroporous structure to significantly enhance the HOR activity as well as the CO tolerance, which is constructed by interface engineering and defect strategy to anchor highly dispersed Pt nanoparticles onto the three-dimensional MoO2-x-C framework. The optimized 2Pt-MoO2-x-C with 1.02 wt% Pt demonstrates higher HOR peak current density (3.57 mA cm-2) and nearly 25 times higher mass activity than 20 wt% Pt/C. The excellent HOR performance is attributed to the synergistic effect between Pt and MoO2-x species, in which the charge transfer from Pt to MoO2-x improves H2 adsorption ability of Pt and accelerates the activation of H2 due to the reduced hydrogen binding energy of MoO2-x caused by Pt-O construction, leading to the release of H* thereby the enhancement of HOR activity. The construction of three-dimensional macroporous structure enhances the HOR dynamics by promoting the conductivity, mass transfer and the exposure of active sites. Moreover, the formed Mo-OH in Pt-MoO2-x-C can effectively react with CO species to remove the CO poisoning of Pt, endowing the excellent CO tolerance.

Molten Salt-Assisted Synthesis of Catalysts for Energy Conversion

A breakthrough in manufacturing procedures often enables people to obtain the desired functional materials. For the field of energy conversion, designing and constructing catalysts with high cost-effectiveness is urgently needed for commercial requirements. Herein, the molten salt-assisted synthesis (MSAS) strategy is emphasized, which combines the advantages of traditional solid and liquid phase synthesis of catalysts. It not only provides sufficient kinetic accessibility, but effectively controls the size, morphology, and crystal plane features of the product, thus possessing promising application prospects. Specifically, the selection and role of the molten salt system, as well as the mechanism of molten salt assistance are analyzed in depth. Then, the creation of the catalyst by the MSAS and the electrochemical energy conversion related application are introduced in detail. Finally, the key problems and countermeasures faced in breakthroughs are discussed and look forward to the future. Undoubtedly, this systematical review and insights here will promote the comprehensive understanding of the MSAS and further stimulate the generation of new and high efficiency catalysts.

Regulating Ru-O Bond and Oxygen Vacancies of RuO2 by Ta Doping for Electrocatalytic Oxygen Evolution in Acid Media

Proton exchange membrane water electrolysis (PEMWE) is considered an ideal green hydrogen production technology with promising application prospects. However, the development of efficient and stable acid electroanalytic oxygen electrocatalysts is still a challenging bottleneck. This progress is achieved by adopting a strategic approach with the introduction of the high valence metal Ta to regulate the electronic configuration of RuO2 by manipulating its local microenvironment to optimize the stability and activity of the electrocatalysts. The Ta-RuO2 catalysts are notable for their excellent electrocatalytic activity, as evidenced by an overpotential of only 202 mV at 10 mA cm-2, which significantly exceeds that of homemade RuO2 and commercial RuO2. Furthermore, the Ta-RuO2 catalyst exhibits exceptional stability with negligible potential reduction observed after 50 h of electrolysis. Theoretical calculations show that the asymmetric configuration of Ru-O-Ta breaks the thermodynamic activity limitations usually associated with adsorption evolution, weakening the energy barrier for the formation of the OOH* formation. The strategic approach presented in this study provides an important reference for the development of a stable active center for acid water splitting.

Stability of electrocatalytic OER: from principle to application

Hydrogen energy, derived from the electrolysis of water using renewable energy sources such as solar, wind, and hydroelectric power, is considered a promising form of energy to address the energy crisis. However, the anodic oxygen evolution reaction (OER) poses limitations due to sluggish kinetics. Apart from high catalytic activity, the long-term stability of electrocatalytic OER has garnered significant attention. To date, several research studies have been conducted to explore stable electrocatalysts for the OER. A comprehensive review is urgently warranted to provide a concise overview of the recent advancements in the electrocatalytic OER stability, encompassing both electrocatalyst and device developments. This review aims to succinctly summarize the primary factors influencing OER stability, including morphological/phase change and electrocatalyst dissolution, as well as mechanical detachment, alongside chemical, mechanical, and operational degradation observed in devices. Furthermore, an overview of contemporary approaches to enhance stability is provided, encompassing electrocatalyst design (structural regulation, protective layer coating, and stable substrate anchoring) and device optimization (bipolar plates, gas diffusion layers, and membranes). Hopefully, more attention will be paid to ensuring the stable operation of electrocatalytic OER and the future large-scale water electrolysis applications. This review presents design principles aimed at addressing challenges related to the stability of electrocatalytic OER.

Unveiling the potential of amorphous nanocatalysts in membrane-based hydrogen production

Hydrogen, as a clean and renewable energy source, is a promising candidate to replace fossil fuels and alleviate the environmental crisis. Compared with the traditional H-type cells with a finite-gap, the design of membrane electrodes can reduce the gas transmission resistance, enhance the current density, and improve the efficiency of hydrogen production. However, the harsh environment in the electrolyser makes the membrane electrode based water electrolysis technology still limited by the lack of catalyst activity and stability under the working conditions. Due to the abundant active sites and structural flexibility, amorphous nanocatalysts are alternatives. In this paper, we review the recent research progress of amorphous nanomaterials as electrocatalysts for hydrogen production by electrolysis at membrane electrodes, illustrate and discuss their structural advantages in membrane electrode catalytic systems, as well as explore the significance of the amorphous structure for the development of membrane electrode systems. Finally, the article also looks at future opportunities and adaptations of amorphous catalysts for hydrogen production at membrane electrodes. The authors hope that this review will deepen the understanding of the potential of amorphous nanomaterials for application in electrochemical hydrogen production, facilitating future nanomaterials research and new sustainable pathways for hydrogen production.

Breaking the Bottleneck of Activity and Stability of RuO2-Based Electrocatalysts for Acidic Oxygen Evolution

Electrochemical acidic oxygen evolution reaction (OER) is an important part for water electrolysis utilizing a proton exchange membrane (PEM) apparatus for industrial H2 production. RuO2 has garnered considerable attention as a potential acidic OER electrocatalyst. However, the overoxidation of Ru active sites under high potential conditions is usually harmful for activity and stability, thereby posing a challenge for large-scale commercialization, which needs effective strategies to circumvent the leaching of Ru and further activate Ru sites. Herein, a Mini-Review is presented to summarize the recent developments regarding the activation and stabilization of the Ru active sites and lattice oxygen through the modulation of the d-band center, coordination environment, bridged heteroatoms, and vacancy engineering, as well as structural protection strategies and reaction pathway optimization to promote the acidic OER activity and stability of RuO2-based electrocatalysts. This Mini-Review offers a profound understanding of the design of RuO2-based electrocatalysts with greatly enhanced acidic OER performances.

Dual active site-mediated Ir single-atom-doped RuO2 catalysts for highly efficient and stable water splitting

The electronic structure modulation through heterogeneous single-atom doping is an effective strategy to improve electrocatalysis performance of catalysts. Here, Ir single-atom doped RuO2 (IrSA/RuO2) is constructed by substituting Ru sites with mono-disperse Ir atoms in RuO2 crystals. The IrSA/RuO2-850 catalyst shows excellent activity for the hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in alkaline media, with overpotentials of only 37 and 234 mV respectively, at a current density of 10 mA cm-2, lower than that of commercial Pt/C (39 mV-HER) and RuO2 (295 mV-OER). Notably, no significant degradation occurs during the 1000 h HER stability test at 500 mA cm-2. Furthermore, IrSA/RuO2-850 also demonstrates superior catalytic activity and stability in acidic media. Theoretical calculations show that the interaction between Ir and RuO2 modulates the electronic structure of both Ru and Ir sites, resulting in the lowest reaction energy barriers of Ru and Ir sites for the HER and OER, respectively, which thermodynamically explains the enhancement of the catalytic activity. Besides, the introduction of Ir atoms also enhances the demetallation energy of Ru atoms and strengthens the structural stability of the crystal, leading to the improved stability of the catalyst. This work provides an effective strategy for construction of high-performing catalysts by precisely controlling the electronic structure and active sites of polymetal atoms.

Materials Containing Single-, Di-, Tri-, and Multi-Metal Atoms Bonded to C, N, S, P, B, and O Species as Advanced Catalysts for Energy, Sensor, and Biomedical Applications

Modifying the coordination or local environments of single-, di-, tri-, and multi-metal atom (SMA/DMA/TMA/MMA)-based materials is one of the best strategies for increasing the catalytic activities, selectivity, and long-term durability of these materials. Advanced sheet materials supported by metal atom-based materials have become a critical topic in the fields of renewable energy conversion systems, storage devices, sensors, and biomedicine owing to the maximum atom utilization efficiency, precisely located metal centers, specific electron configurations, unique reactivity, and precise chemical tunability. Several sheet materials offer excellent support for metal atom-based materials and are attractive for applications in energy, sensors, and medical research, such as in oxygen reduction, oxygen production, hydrogen generation, fuel production, selective chemical detection, and enzymatic reactions. The strong metal-metal and metal-carbon with metal-heteroatom (i.e., N, S, P, B, and O) bonds stabilize and optimize the electronic structures of the metal atoms due to strong interfacial interactions, yielding excellent catalytic activities. These materials provide excellent models for understanding the fundamental problems with multistep chemical reactions. This review summarizes the substrate structure-activity relationship of metal atom-based materials with different active sites based on experimental and theoretical data. Additionally, the new synthesis procedures, physicochemical characterizations, and energy and biomedical applications are discussed. Finally, the remaining challenges in developing efficient SMA/DMA/TMA/MMA-based materials are presented.

Constructing CoP/Ni2P Heterostructure Confined Ru Sub-Nanoclusters for Enhanced Water Splitting in Wide pH Conditions

Developing efficient electrocatalysts for water splitting is of great significance for realizing sustainable energy conversion. In this work, Ru sub-nanoclusters anchored on cobalt-nickel bimetallic phosphides (Ru-CoP/Ni2P) are constructed by an interfacial confinement strategy. Remarkably, Ru-CoP/Ni2P with low noble metal loading (33.1 µg cm-2) shows superior activity for hydrogen evolution reaction (HER) in all pH values, whose turnover frequency (TOF) is 8.7, 15.3, and 124.7 times higher than that of Pt/C in acidic, alkaline, and neutral conditions, respectively. Meanwhile, it only requires the overpotential of 171 mV@10 mA cm-2 for oxygen evolution reaction (OER) and corresponding TOF is 20.3 times higher than that of RuO2. More importantly, the Ru-CoP/Ni2P||Ru-CoP/Ni2P displays superior mass activity of 4017 mA mgnoble metal -1 at 2.0 V in flowing alkaline water electrolyzer, which is 105.1 times higher than that of Pt/C||IrO2. In situ Raman spectroscopy demonstrates that the Ru sites in Ru-CoP/Ni2P play a key role for water splitting and follow the adsorption evolution mechanism toward OER. Further mechanism studies disclose the confined Ru atom contributes to the desorption of H2 during HER and the formation of O-O bond during OER, leading to fast reaction kinetics. This study emphasizes the importance of interface confinement for enhancing electrocatalytic activity.

Accelerated Proton Transfer in Asymmetric Active Units for Sustainable Acidic Oxygen Evolution Reaction

The poor durability of Ru-based catalysts limits the practical application in proton exchange membrane water electrolysis (PEMWE). Here, we report that the asymmetric active units in Ru1-xMxO2 (M = Sb, In, and Sn) binary solid solution oxides are constructed by introducing acid-resistant p-block metal sites, breaking the activity and stability limitations of RuO2 in acidic oxygen evolution reaction (OER). Constructing highly asymmetric Ru-O-Sb units with a strong electron delocalization effect significantly shortens the spatial distance between Ru and Sb sites, improving the bonding strength of the overall structure. The unique two-electron redox couples at Sb sites in asymmetric active units trigger additional chemical steps at different OER stages, facilitating continuous proton transfer. The optimized Ru0.8Sb0.2O2 solid solution requires a superlow overpotential of 160 mV at 10 mA cm-2 and a record-breaking stability of 1100 h in an acidic electrolyte. Notably, the scale-prepared Ru0.8Sb0.2O2 achieves efficient PEMWE performance under industrial conditions. General mechanism analysis shows that the enhanced proton transport in the asymmetric Ru-O-M unit provides a new working pathway for acidic OER, breaking the scaling relationship without sacrificing stability.

Ni and Co Active Site Transition and Competition in Fluorine-Doped NiCo(OH)2 LDH Electrocatalysts for Oxygen Evolution Reaction

The oxygen evolution reaction (OER) performance of NiCo LDH electrocatalysts can be improved through fluorine doping. The roles of Ni and Co active sites in such catalysts remain ambiguous and controversial. In addressing the issue, this study draws upon the molecular orbital theory and proposes the active center competitive mechanism between Ni and Co. The doped F-atoms can directly impact the valence state of metal atoms or exert an indirect influence through the dehydrogenation, thereby modulating the active center. As the F-atoms are progressively aggregate, the eg orbitals of Ni and Co transition from e2 g to e1 g, and subsequently to e0 g. The corresponding valence state elevates from +2 to +3, and then to +4, signifying an initial increase followed by a subsequent decrease in the electrocatalytic performance. Furthermore, a series of F-NiCo LDH catalysts are synthesized to verify the eg orbital occupancy analysis, and the catalytic OER overpotentials are 303, 243, 240, and 246 mV at the current density of 10 mA cm-2, respectively, which coincides well with the theoretical prediction. This investigation not only provides novel mechanistic insights into the transition and competition of Ni and Co in F-NiCo LDH catalysts but also establishes a foundation for the design of high-performance catalysts.