Cell surface analysis techniques: What do cell preparation protocols do to cell surface properties?

Evaluation of aerobic granulation performance bioaugmented with the auto-aggregating bacterium Pseudomonas stutzeri strain XL-2 with heterotrophic nitrification-aerobic denitrification capacity

In this study, the possibility of an auto-aggregating bacterium Pseudomonas strain XL-2 with heterotrophic nitrification-aerobic denitrification capacity for improving granulation and nitrogen removal was evaluated. The results showed that the supplementation of strain XL-2 promoted granulation, making R1 (experimental group with strain XL-2) dominated by granules at 14 d, which was 12 days earlier than R2 (control group without strain XL-2). This was attributed to the promotion of extracellular polymeric substances (EPS) secretion, particularly proteins by adding strain XL-2, thereby improving the hydrophobicity of sludge and altering the proteins secondary structures to facilitate aggregation. Meanwhile, adding strain XL-2 improved simultaneous nitrification and denitrification efficiency of R1. Microbial community analysis indicated that strain XL-2 successfully proliferated in aerobic granule sludge and might induce the enrichment of genera such as Flavobacterium and Paracoccus that were favorable for EPS secretion and denitrification, jointly promoting granulation and enhancing nitrogen removal efficiency.

Nutrient enrichment increases virulence in an opportunistic environmental pathogen, with greater effect at low bacterial doses

Eutrophication of aquatic ecosystems is associated with an increased risk of pathogen infection via increased pathogen growth and host exposure via increased pathogen doses. Here, we studied the effect of nutrients on the virulence of an opportunistic bacterial pathogen of fish, Flavobacterium columnare, in challenge experiments with rainbow trout fingerlings. We hypothesized that removing all nutrients by washing the bacteria would reduce virulence as compared to unwashed bacteria, but adding nutrients to the tank water would increase the virulence of the bacterium. Nutrient addition and increase in bacterial dose increased virulence for both unwashed and washed bacteria. For unwashed bacteria, the addition of nutrients reduced the survival probability of fish challenged with low bacterial doses more than for fish challenged with higher bacterial doses, suggesting activation of bacterial virulence factors. Washing and centrifugation reduced viable bacterial counts, and the addition of washed bacteria alone did not lead to fish mortality. However, a small addition of nutrient medium, 0.05% of the total water volume, added separately to the fish container, restored the virulence of the washed bacteria. Our results show that human-induced eutrophication could trigger epidemics of aquatic pathogens at the limits of their survival and affect their ecology and evolution by altering the dynamics between strains that differ in their growth characteristics.

Illuminating the Tiny World: A Navigation Guide for Proper Raman Studies on Microorganisms

Raman spectroscopy is an emerging method for the identification of bacteria. Nevertheless, a lot of different parameters need to be considered to establish a reliable database capable of identifying real-world samples such as medical or environmental probes. In this review, the establishment of such reliable databases with the proper design in microbiological Raman studies is demonstrated, shining a light into all the parts that require attention. Aspects such as the strain selection, sample preparation and isolation requirements, the phenotypic influence, measurement strategies, as well as the statistical approaches for discrimination of bacteria, are presented. Furthermore, the influence of these aspects on spectra quality, result accuracy, and read-out are discussed. The aim of this review is to serve as a guide for the design of microbiological Raman studies that can support the establishment of this method in different fields.

Set-up of a pharmaceutical cell bank of Magnetospirillum gryphiswaldense MSR1 magnetotactic bacteria producing highly pure magnetosomes

We report the successful fabrication of a pharmaceutical cellular bank (PCB) containing magnetotactic bacteria (MTB), which belong to the Magnetospirillum gryphiswaldense MSR1 species. To produce such PCB, we amplified MTB in a minimal growth medium essentially devoid of other heavy metals than iron and of CMR (Carcinogenic, mutagenic and reprotoxic) products. The PCB enabled to acclimate MTB to such minimal growth conditions and then to produce highly pure magnetosomes composed of more than 99.9% of iron. The qualification of the bank as a PCB relies first on a preserved identity of the MTB compared with the original strain, second on genetic bacterial stability observed over 100 generations or under cryo-preservation for 16 months, third on a high level of purity highlighted by an absence of contaminating microorganisms in the PCB. Furthermore, the PCB was prepared under high-cell load conditions (9.108 cells/mL), allowing large-scale bacterial amplification and magnetosome production. In the future, the PCB could therefore be considered for commercial as well as research orientated applications in nanomedicine. We describe for the first-time conditions for setting-up an effective pharmaceutical cellular bank preserving over time the ability of certain specific cells, i.e. Magnetospirillum gryphiswaldense MSR1 MTB, to produce nano-minerals, i.e. magnetosomes, within a pharmaceutical setting.

Guidelines for an optimized differential centrifugation of cells

Literature reviews reveal a significant deficiency in conceptual comprehension concerning centrifugation, a crucial step in both medical and research protocols. The arbitrary fluctuations in centrifugal forces present a potential threat to the reproducibility of results. To address this, we propose concise guidelines that integrate key factors such as temperature, osmolarity, fluid volume, and viscosity. These guidelines aim to enhance comprehension of optimal sedimentation conditions for cell suspensions. Additionally, we introduce a standardized protocol for determining the optimal RCF and centrifugation time. The goal is to maximize sedimentation efficiency while minimizing cell damage, contributing to a universally applicable and reproducible method in centrifugation practices.

Predicting phosphorus accumulation and proposing conditions needed for an algal-based phosphorus uptake process

Algal-based waste stabilisation ponds (WSP) are a common wastewater treatment system for small communities but have poor phosphorus removal. Under certain conditions algae in WSPs will perform 'luxury uptake' increasing their phosphorus content to over 3% (gP/gSS) by storing polyphosphate. For the first time in the literature this paper presents a systematic study which determines the conditions needed to maximise phosphorus accumulation within WSP biomass taking into account the interactions between key variables. The key variables of temperature, phosphorus concentration, light intensity, mixing intensity, organic load, and pH were evaluated in 40 batch factorial experiments using a WSP algal culture. All six variables examined had significant main effects or interactions on the phosphorus content of the biomass. These were incorporated into a regression equation which was successfully validated against independent data sets from the literature. The conditions required to maximise the phosphorus content of the biomass were predicted for both summer (high light and high temperature) and winter (low light and low temperature) scenarios. The required conditions were revealed to be high phosphorus concentration, high mixing intensity, no supplementary CO2 addition, and low organic load. Interestingly, these conditions were consistent for both summer and winter suggesting that year-round treatment is possible. Practical methods of achieving these conditions were proposed. While further work will be needed to evaluate the effect of growth and potential influence of algal species, the findings presented provide a vital step towards developing a new phosphorus removal treatment process based on an enhanced understanding of environmental biotechnology.

Novel expression system based on enhanced permeability of Vibrio natriegens cells induced by D,D- carboxypeptidase overexpression

Vibrio natriegens is a fast-growing, non-pathogenic marine bacterium with promising features for biotechnological applications such as high-level recombinant protein production or fast DNA propagation. A remarkable short generation time (< 10 min), robust proteosynthetic activity and versatile metabolism with abilities to utilise wide range of substrates contribute to its establishment as a future industrial platform for fermentation processes operating with high productivity.D,D-carboxypeptidases are membrane-associated enzymes involved in peptidoglycan biosynthesis and cell wall formation. This study investigates the impact of overexpressed D,D-carboxypeptidases on membrane integrity and the increased leakage of intracellular proteins into the growth medium in V. natriegens. Our findings confirm that co-expression of these enzymes can enhance membrane permeability, thereby facilitating the transport of target proteins into the extracellular environment, without the need for secretion signals, tags, or additional permeabilization methods. Using only a single step IMAC chromatography, we were able to purify AfKatG, MDBP or Taq polymerase in total yields of 117.9 ± 56.0 mg/L, 36.5 ± 12.9 mg/L and 26.5 ± 6.0 mg/L directly from growth medium, respectively. These results demonstrate the feasibility of our V. natriegens based system as a broadly applicable extracellular tag-less recombinant protein producer.

Immunomagnetic separation coupled with flow cytometry for the analysis of Legionella pneumophila in aerosols

Legionella pneumophila are pathogenic bacteria that can be found in high concentrations in artificial water systems like evaporative cooling towers, which have been the source of frequent outbreaks in recent years. Since inhaled L. pneumophila can lead to Legionnaires' disease, the development of suitable sampling and rapid analysis strategies for these bacteria in aerosols is therefore of great relevance. In this work, different concentrations of viable L. pneumophila Sg 1 were nebulized and sampled by the cyclone sampler Coriolis® µ under defined conditions in a bioaerosol chamber. To quantify intact Legionella cells, the collected bioaerosols were subsequently analyzed by immunomagnetic separation coupled with flow cytometry (IMS-FCM) on the platform rqmicro.COUNT. For analytical comparison, measurements with qPCR and cultivation were performed. Limits of detection (LOD) of 2.9 × 10³ intact cells m^-3 for IMS-FCM and 7.8 × 10² intact cells m^-3 for qPCR indicating a comparable sensitivity as in culture (LOD = 1.5 × 10³ culturable cells m^-3). Over a working range of 10³ - 10⁶ cells mL^-1, the analysis of nebulized and collected aerosol samples with IMS-FCM and qPCR provides higher recovery rates and more consistent results than by cultivation. Overall, IMS-FCM is a suitable culture-independent method for quantification of L. pneumophila in bioaerosols and is promising for field application due to its simplicity in sample preparation.

Label-free and noninvasive analysis of microorganism surface epistructures at the single-cell level

Cell surface properties of microorganisms provide abundant information for their physiological status and fate choice. However, current methods for analyzing cell surface properties require labeling or fixation, which can alter the cell activity. This study establishes a label-free, rapid, noninvasive, and quantitative analysis of cell surface properties, including the presence and the dimension of epistructure, down to the single-cell level and at the nanometer scale. Simultaneously, electrorotation provides dielectric properties of intracellular contents. With the combined information, the growth phase of microalgae cells can be identified. The measurement is based on electrorotation of single cells, and an electrorotation model accounting for the surface properties is developed to properly interpret experimental data. The epistructure length measured by electrorotation is validated by scanning electron microscopy. The measurement accuracy is satisfactory in particular in the case of microscale epistructures in the exponential phase and nanoscale epistructures in the stationary phase. However, the measurement accuracy for nanoscale epistructures on cells in the exponential phase is offset by the effect of a thick double layer. Lastly, a diversity in epistructure length distinguishes exponential phase from stationary phase.

Experimental and Analytical Approaches for Improving the Resolution of Randomly Barcoded Transposon Insertion Sequencing (RB-TnSeq) Studies

Randomly barcoded transposon insertion sequencing (RB-TnSeq) is an efficient, multiplexed method to determine microbial gene function during growth under a selection condition of interest. This technique applies to growth, tolerance, and persistence studies in a variety of hosts, but the wealth of data generated can complicate the identification of the most critical gene targets. Experimental and analytical methods for improving the resolution of RB-TnSeq are proposed, using Pseudomonas putida KT2440 as an example organism. Several key parameters, such as baseline media selection, substantially influence the determination of gene fitness. We also present options to increase statistical confidence in gene fitness, including increasing the number of biological replicates and passaging the baseline culture in parallel with selection conditions. These considerations provide practitioners with several options to identify genes of importance in TnSeq data sets, thereby streamlining metabolic characterization.

Two-Dimensional Cell Separation: a High-Throughput Approach to Enhance the Culturability of Bacterial Cells from Environmental Samples

Culture-independent sequence data from various environmental samples have revealed an immense microbial diversity of environmental, clinical, and industrial importance that has not yet been cultured. Cultivation is imperative to validate findings emerging from cultivation-independent molecular data and exploit the isolated organisms for biotechnological purposes. Efforts have been made to boost the cultivability of microbes from environmental samples by use of a range of techniques and instrumentation. The manuscript presents a novel yet simple and innovative approach to improving the cultivability of natural microorganisms without sophisticated instrumentation. By employing gradient centrifugation combined with serial dilution (“two-dimensional cell separation”), significantly higher numbers of genera (>2-fold higher) and species (>3-fold higher) were isolated from environmental samples, including soil, anaerobic sludge, and landfill leachate, than from using serial dilution alone. This simple and robust protocol can be modified for any environment and culture medium and provides access to untapped microbial diversity.

IMPORTANCE In the manuscript, we have developed a novel yet simple and innovative approach to improving the cultivability of natural microorganisms without sophisticated instrumentation. The method used gradient centrifugation combined with serial dilution (two-dimensional cell separation) to improve taxum recovery from samples. This simple and robust protocol can be modified for any environment and culture medium and provides access to untapped microbial diversity. This approach can be incorporated with less labor and complexity in laboratories with minimal instrumentation. As cultivation is a workflow that is well suited to lower-resource microbiology labs, we believe improvements in cultivability can increase opportunities for scientific collaborations between low-resource labs and groups focused on high-resource cultivation-independent methodologies.

Phosphorus deficiency leads to the loosening of activated sludge: The role of exopolysaccharides in aggregation

Whether phosphorus deficiency in influent will affect the aggregation and sedimentation of activated sludge needs to be further clarified. This paper systematically studied the structure, aggregation and settlement of activated sludge, and the composition, properties and chemical structure of extracellular polymers and microbial community structure of sludge under different influent phosphorus contents to determine the causes of sludge aggregation and structural deterioration. The results show that phosphorus deficiency in influent leads to a decrease in the aggregation capacity and a loose structure of activated sludge, and the reduction of hydrophobic interactions is the main factor of sludge aggregation and structural deterioration. The content, functional groups and protein secondary structure of extracellular protein were almost unchanged. An increase in the content and hydrophilicity of extracellular polysaccharide (PS) results in a decrease in sludge hydrophobicity. Under phosphorus deficiency, the changes in microbial species related to PS secretion were the reasons for the increase in PS content and hydrophilicity. The negative effects of PS content and hydrophilicity on sludge aggregation and structure are important findings of this work and are expected to be useful for better understanding the restoration of activated sludge performance in the treatment of phosphorus-deficient wastewater.

Factors influencing environmental sampling recovery of healthcare pathogens from non-porous surfaces with cellulose sponges

Results from sampling healthcare surfaces for pathogens are difficult to interpret without understanding the factors that influence pathogen detection. We investigated the recovery of four healthcare-associated pathogens from three common surface materials, and how a body fluid simulant (artificial test soil, ATS), deposition method, and contamination levels influence the percent of organisms recovered (%R). Known quantities of carbapenemase-producing KPC+ Klebsiella pneumoniae (KPC), Acinetobacter baumannii, vancomycin-resistant Enterococcus faecalis, and Clostridioides difficile spores (CD) were suspended in Butterfield's buffer or ATS, deposited on 323cm2 steel, plastic, and laminate surfaces, allowed to dry 1h, then sampled with a cellulose sponge wipe. Bacteria were eluted, cultured, CFU counted and %R determined relative to the inoculum. The %R varied by organism, from <1% (KPC) to almost 60% (CD) and was more dependent upon the organism's characteristics and presence of ATS than on surface type. KPC persistence as determined by culture also declined by >1 log10 within the 60 min drying time. For all organisms, the %R was significantly greater if suspended in ATS than if suspended in Butterfield's buffer (p<0.05), and for most organisms the %R was not significantly different when sampled from any of the three surfaces. Organisms deposited in multiple droplets were recovered at equal or higher %R than if spread evenly on the surface. This work assists in interpreting data collected while investigating a healthcare infection outbreak or while conducting infection intervention studies.

Pharmacodynamics of Moxifloxacin, Meropenem, Caspofungin and their Combinations Against In Vitro Polymicrobial Inter-kingdom Biofilms

Biofilms colonize medical devices and are often recalcitrant to antibiotics. Inter-kingdom biofilms, when at least a bacterium and a fungus are co-isolated, increase the likelihood of therapeutic failures. In this work, a three-species in vitro biofilm model including S. aureus, E. coli and C. albicans was used to study the activity of the antibiotics moxifloxacin and meropenem, the antifungal caspofungin, and combinations of them against inter-kingdom biofilms. The culturable cells and total biomass were evaluated to determine the pharmacodynamic parameters of the drug response for the incubation with the drugs alone. The synergic or antagonistic effects (increased/decreased effects) of the combination of drugs were analysed with the highest single agent method. Biofilms were imaged in confocal microscopy after live/dead staining. The drugs had limited activity when used alone against single-, dual- or three-species biofilms. When used in combination, additive effects were observed against single- or dual-species biofilms, and increased effects (synergy) against biomass of three-species biofilms. In addition, the two antibiotics showed different patterns, moxifloxacin being more active when targeting S. aureus and meropenem when targeting E. coli. All these observations were confirmed by confocal microscopy images. Our findings highlight the interest in combining caspofungin with antibiotics against inter-kingdom biofilms.

Extracellular electron transfer influences the transport and retention of ferrihydrite nanoparticles in quartz sand coated with Shewanella oneidensis biofilm

Microbial biofilm has been found to impact the mobility of nanoparticles in saturated porous media by altering physicochemical properties of collector surface. However, little is known about the influence of biofilm's biological activity on nanoparticle transport and retention. Here, the transport of ferrihydrite nanoparticles (FhNPs) was studied in quartz sands coated with biofilm of Shewanella oneidensis MR-1 that is capable of reducing Fe(III) through extracellular electron transfer (EET). It was found that MR-1 biofilm coating enhanced FhNPs' deposition under different pH/ionic strength conditions and humic acid concentrations. More importantly, when the influent electron donor (glucose) concentration was increased to promote biofilm's EET activity, the breakthrough of FhNPs in biofilm-coated sands was inhibited. A lack of continuous and stable supply of electron donor, on the contrary, led to remobilization and release of the originally retained FhNPs. Column experiments with biofilm of EET-deficient MR-1 mutants (ΔomcA/ΔmtrC and ΔcymA) further indicated that the impairment of EET activity decreased the retention of FhNPs. It is proposed that the effective surface binding and adhesion of FhNPs that is required by direct EET cannot be neglected when evaluating the transport of FhNPs in sands coated with electroactive biofilm.

Disrupting Irreversible Bacterial Adhesion and Biofilm Formation with an Engineered Enzyme

Biofilm formation is often attributed to postharvest bacterial persistence on fresh produce and food handling surfaces. In this study, a predicted glycosyl hydrolase enzyme was expressed, purified, and validated for the removal of microbial biofilms from biotic and abiotic surfaces under conditions used for chemical cleaning agents. Crystal violet biofilm staining assays revealed that 0.1 mg/ml of enzyme inhibited up to 41% of biofilm formation by Escherichia coli O157:H7, E. coli 25922, Salmonella enterica serovar Typhimurium, and Listeria monocytogenes. Furthermore, the enzyme was effective at removing mature biofilms, providing a 35% improvement over rinsing with a saline solution alone. Additionally, a parallel-plate flow cell was used to directly observe and quantify the impact of enzyme rinses on E. coli O157:H7 cells adhering to spinach leaf surfaces. The presence of 1 mg/liter enzyme resulted in nearly 6-times-higher detachment rate coefficients than a deionized (DI) water rinse, while the total cells removed from the surface increased from 10% to 25% over the 30-min rinse time, reversing the initial phases of biofilm formation. Enzyme treatment of all 4 cell types resulted in significantly reduced cell surface hydrophobicity and collapse of negatively stained E. coli 25922 cells imaged by electron microscopy, suggesting potential polysaccharide surface modification of enzyme-treated bacteria. Collectively, these results point to the broad substrate specificity and robustness of the enzyme for different types of biofilm stages, solution conditions, and pathogen biofilm types and may be useful as a method for the removal or inhibition of bacterial biofilm formation. IMPORTANCE In this study, the ability of an engineered enzyme to reduce bacterial adhesion and biofilm formation of several foodborne pathogens was demonstrated, representing a promising option for enhancing or replacing chlorine and other chemical sanitizers in food processing applications. Specifically, significant reductions of biofilms of the pathogens Escherichia coli O157:H7, Salmonella Typhimurium, and Listeria monocytogenes are observed, as are reductions in initial adhesion. Enzymes have the added benefits of being green, sustainable alternatives to chemical sanitizers, as well as having a minimal impact on food properties, in contrast to many alternative antimicrobial options such as bleach that aim to minimize food safety risks.

Environmental dissolved DNA harbours meaningful biological information on microbial community structure

Extracellular DNA (eDNA) comprises all the DNA molecules outside cells. This component of microbial ecosystems may serve as a source of nutrients and genetic information. Hypersaline environments harbour one of the highest concentrations of eDNA reported for natural systems, which has been attributed to the physicochemical preservative effect of salts and to high viral abundance. Here, we compared centrifugation and filtration protocols for the extraction of dissolved DNA (dDNA, as opposed to eDNA that also includes DNA from free viral particles) from a solar saltern crystallizer pond (CR30) water sample. The crystallizer dDNA fraction has been characterized, for the first time, and compared with cellular and viral metagenomes from the same location. High-speed centrifugation affected CR30 dDNA concentration and composition due to cell lysis, highlighting that protocol optimization should be the first step in dDNA studies. Crystallizer dDNA, which accounted for lower concentrations than those previously reported for hypersaline anoxic sediments, had a mixed viral and cellular origin, was enriched in archaeal DNA and had a distinctive taxonomic composition compared to that from the cellular assemblage of the same sample. Bioinformatic analyses indicated that nanohaloarchaeal viruses could be a cause for these differences.

A systematic framework for using membrane metrics for strain engineering

The cell membrane plays a central role in the fitness and performance of microbial cell factories and therefore it is an attractive engineering target. The goal of this work is to develop a systematic framework for identifying membrane features for use as engineering targets. The metrics that describe the composition of the membrane can be visualized as "knobs" that modulate various "outcomes", such as physical properties of the membrane and metabolic activity in the form of growth and productivity, with these relationships varying depending on the condition. We generated a set of strains with altered membrane lipid composition via expression of des, fabA and fabB and performed a rigorous characterization of these knobs and outcomes across several individual inhibitory conditions. Here, the knobs are the relative abundance of unsaturated lipids and lipids containing cyclic rings; the average lipid length, and the ratio of linear and non-linear lipids (L/nL ratio). The outcomes are membrane permeability, hydrophobicity, fluidity, and specific growth rate. This characterization identified significant correlations between knobs and outcomes that were specific to individual inhibitors, but also were significant across all tested conditions. For example, across all conditions, the L/nL ratio is positively correlated with the cell surface hydrophobicity, and the average lipid length is positively correlated with specific growth rate. A subsequent analysis of the data with the individual inhibitors identified pairs of lipid metrics and membrane properties that were predicted to impact cell growth in seven modeled scenarios with two or more inhibitors. The L/nL ratio and the membrane hydrophobicity were predicted to impact cell growth with the highest frequency. We experimentally validated this prediction in the combined condition of 42 °C, 2.5 mM furfural and 2% v/v ethanol in minimal media. Membrane hydrophobicity was confirmed to be a significant predictor of ethanol production. This work demonstrates that membrane physical properties can be used to predict the performance of biocatalysts in single and multiple inhibitory conditions, and possibly as an engineering target. In this manner, membrane properties can possibly be used as screening or selection metrics for library- or evolution-based strain engineering.

Polymeric Materials Used for Immobilisation of Bacteria for the Bioremediation of Contaminants in Water

Bioremediation is a key process for reclaiming polluted soil and water by the use of biological agents. A commonly used approach aims to neutralise or remove harmful pollutants from contaminated areas using live microorganisms. Generally, immobilised microorganisms rather than planktonic cells have been used in bioremediation methods. Activated carbon, inorganic minerals (clays, metal oxides, zeolites), and agricultural waste products are acceptable substrates for the immobilisation of bacteria, although there are limitations with biomass loading and the issue with leaching of bacteria during the process. Various synthetic and natural polymers with different functional groups have been used successfully for the efficient immobilisation of microorganisms and cells. Promise has been shown using macroporous materials including cryogels with entrapped bacteria or cells in applications for water treatment and biotechnology. A cryogel is a macroporous polymeric gel formed at sub-zero temperatures through a process known as cryogelation. Macroporous hydrogels have been used to make scaffolds or supports for immobilising bacterial, viral, and other cells. The production of composite materials with immobilised cells possessing suitable mechanical and chemical stability, porosity, elasticity, and biocompatibility suggests that these materials are potential candidates for a range of applications within applied microbiology, biotechnology, and research. This review evaluates applications of macroporous cryogels as tools for the bioremediation of contaminants in wastewater.

Physics Comes to the Aid of Medicine-Clinically-Relevant Microorganisms through the Eyes of Atomic Force Microscope

Despite the hope that was raised with the implementation of antibiotics to the treatment of infections in medical practice, the initial enthusiasm has substantially faded due to increasing drug resistance in pathogenic microorganisms. Therefore, there is a need for novel analytical and diagnostic methods in order to extend our knowledge regarding the mode of action of the conventional and novel antimicrobial agents from a perspective of single microbial cells as well as their communities growing in infected sites, i.e., biofilms. In recent years, atomic force microscopy (AFM) has been mostly used to study different aspects of the pathophysiology of noninfectious conditions with attempts to characterize morphological and rheological properties of tissues, individual mammalian cells as well as their organelles and extracellular matrix, and cells’ mechanical changes upon exposure to different stimuli. At the same time, an ever-growing number of studies have demonstrated AFM as a valuable approach in studying microorganisms in regard to changes in their morphology and nanomechanical properties, e.g., stiffness in response to antimicrobial treatment or interaction with a substrate as well as the mechanisms behind their virulence. This review summarizes recent developments and the authors’ point of view on AFM-based evaluation of microorganisms’ response to applied antimicrobial treatment within a group of selected bacteria, fungi, and viruses. The AFM potential in development of modern diagnostic and therapeutic methods for combating of infections caused by drug-resistant bacterial strains is also discussed.

The Bacterium Pantoea ananatis Modifies Behavioral Responses to Sugar Solutions in Honeybees

1. Honeybees, which are among the most important pollinators globally, do not only collect pollen and nectar during foraging but may also disperse diverse microbes. Some of these can be deleterious to agricultural crops and forest trees, such as the bacterium Pantoea ananatis, an emerging pathogen in some systems. P. ananatis infections can lead to leaf blotches, die-back, bulb rot, and fruit rot. 2. We isolated P. ananatis bacteria from flowers with the aim of determining whether honeybees can sense these bacteria and if the bacteria affect behavioral responses of the bees to sugar solutions. 3. Honeybees decreased their responsiveness to different sugar solutions when these contained high concentrations of P. ananatis but were not deterred by solutions from which bacteria had been removed. This suggests that their reduced responsiveness was due to the taste of bacteria and not to the depletion of sugar in the solution or bacteria metabolites. Intriguingly, the bees appeared not to taste ecologically relevant low concentrations of bacteria. 4. Synthesis and applications. Our data suggest that honeybees may introduce P. ananatis bacteria into nectar in field-realistic densities during foraging trips and may thus affect nectar quality and plant fitness.

The influence of extracellular polymeric substances on the coagulation process of cyanobacteria

The hydrophobicity and flocculation properties of cyanobacterial cells are closely related to their extracellular polymeric substances (EPS). During the treatment of drinking water, the coagulation and removal of EPS-wrapped cyanobacterial particles from natural water sources is very difficult. In this work, a series of surface characteristics of cyanobacterial cells with different EPS fractions were analyzed to evaluate their influences on the coagulation process. With the removal of EPS, the coagulation efficiency of cyanobacteria was gradually improved. The intracellular microcystin release showed that the cyanobacterial cells in each EPS removal phase were almost intact with few broken cells. The surface of cyanobacterial cells had higher hydrophobicity and lower zeta potentials with each step of the EPS extraction, which improved the ratio of particles that were in an unstable state. Furthermore, the deeper the EPS extraction phase, the larger the decreased in size of cyanobacterial particles, thus increasing their specific surface area for adsorption with coagulant. It was concluded that the coagulation mechanism of EPS-wrapped cyanobacterial particles was: the cyanobacterial cells were first peeled off through attraction by opposite charges from the coagulant, and then they were adsorbed before settling down. This study provides a scientific basis for the removal of cyanobacteria by enhancing coagulation.

Mosaic-CLSM Assessment of Bacterial Spatial Distribution in Cosmetic Matrices According to Matrix Viscosity and Bacterial Hydrophobicity

The reliability of the challenge test depends, among other parameters, on the spatial distribution of microorganisms in the matrix. The present study aims to quickly identify factors that are susceptible to impair a uniform distribution of inoculated bacteria in cosmetic matrices in this context. We used mosaic confocal laser scanning microscopy (M-CLSM) to obtain rapid assessment of the impact of the composition and viscosity of cosmetic matrices on S. aureus spatial distribution. Several models of cosmetic matrices were formulated with different concentrations of two thickeners and were inoculated with three S. aureus strains having different levels of hydrophobicity. The spatial distribution of S. aureus in each matrix was evaluated according to the frequency distribution of the fluorescence values of at least 1350 CLSM images. We showed that, whatever the thickener used, an increasingly concentration of thickener results in increasingly bacterial clustered distribution. Moreover, higher bacterial hydrophobicity also resulted in a more clustered spatial distribution. In conclusion, CLSM-based method allows a rapid characterization of bacterial spatial distribution in complex emulsified systems. Both matrix viscosity and bacterial surface hydrophobicity affect the bacterial spatial distribution which can have an impact on the reliability of bacterial enumeration during challenge test.

High density cultivation for efficient sesquiterpenoid biosynthesis in Synechocystis sp. PCC 6803

Cyanobacteria and microalgae are attractive photoautotrophic host systems for climate-friendly production of fuels and other value-added biochemicals. However, for economic applications further development and implementation of efficient and sustainable cultivation strategies are essential. Here, we present a comparative study on cyanobacterial sesquiterpenoid biosynthesis in Synechocystis sp. PCC 6803 using a commercial lab-scale High Density Cultivation (HDC) platform in the presence of dodecane as in-situ extractant. Operating in a two-step semi-batch mode over a period of eight days, volumetric yields of (E)-α-bisabolene were more than two orders of magnitude higher than previously reported for cyanobacteria, with final titers of 179.4 ± 20.7 mg * L⁻¹. Likewise, yields of the sesquiterpene alcohols (−)-patchoulol and (−)-α-bisabolol were many times higher than under reference conditions, with final titers of 17.3 ± 1.85 mg * L⁻¹ and 96.3 ± 2.2 mg * L⁻¹, respectively. While specific productivity was compromised particularly for (E)-α-bisabolene in the HDC system during phases of high biomass accumulation rates, volumetric productivity enhancements during linear growth at high densities were more pronounced for (E)-α-bisabolene than for the hydroxylated terpenoids. Together, this study provides additional insights into cell density-related process characteristics, introducing HDC as highly efficient strategy for phototrophic terpenoid production in cyanobacteria.

Planktonic and Sessile Artificial Colonic Microbiota Harbor Distinct Composition and Reestablish Differently upon Frozen and Freeze-Dried Long-Term Storage

Fecal microbiota transplantation has been successfully applied in the treatment of recurrent Clostridium difficile infection and has been suggested as an alternative therapy for other intestinal disorders such as inflammatory bowel disease or metabolic syndrome. “Artificial” colonic microbiota delivered by PolyFermS continuous fermentation models can provide a controllable and reproducible alternative to fecal transplantation, but effective preservation strategies must be developed. In this study, we systematically investigated the response of sessile and planktonic artificial colonic microbiota to cryopreservation and lyophilization. We suggest that functional redundancy is an important factor in providing functional stability with respect to exposure to stress during processing and storage. Functional redundancy in compositionally reduced microbial systems may be considered when designing microbial products for therapy.

Biofilm-associated, sessile communities represent the major bacterial lifestyle, whereas planktonic cells mainly appear during initial colonization of new surfaces. Previous research, mainly performed with pathogens, demonstrated increased environmental stress tolerance of biofilm-growing compared to planktonic bacteria. The lifestyle-specific stress response of colonic microbiota, both natural and fermentation produced, has not been addressed before. Planktonic and sessile “artificial” colonic microbiota delivered by PolyFermS continuous fermentation models can provide a controllable and reproducible alternative to fecal transplantation in treating gastrointestinal disorders. We therefore characterized planktonic and sessile microbiota produced in two PolyFermS models inoculated with immobilized fecal microbiota and comparatively tested their levels of tolerance of frozen storage (–80°C) and freeze-dried storage (4°C) for 9 months to mimic preservation strategies for therapeutic applications. Sessile microbiota harbored next to shared taxa a unique community distinguishable from planktonic microbiota. Synergistetes and Proteobacteria were highly represented in sessile microbiota, while Firmicutes were more abundant in planktonic microbiota. The community structure and metabolic activity of both microbiota, monitored during standardized reactivation batch fermentations, were better preserved after frozen storage than dried storage, indicated by higher Bray-Curtis similarity and enhanced recovery of metabolite production. For both lifestyles, reestablishment of Bacteroidaceae was impaired after frozen and dried storage along with reduced propionate formation. In contrast, butyrate production was maintained after reactivation despite compositional rearrangements within the butyrate-producing community. Unexpectedly, the rate of recovery of metabolite production was lower after preservation of sessile than planktonic microbiota. We speculate that higher functional dependencies between microbes might have led to the lower stress tolerance of sessile than planktonic microbiota.

IMPORTANCE Fecal microbiota transplantation has been successfully applied in the treatment of recurrent Clostridium difficile infection and has been suggested as an alternative therapy for other intestinal disorders such as inflammatory bowel disease or metabolic syndrome. “Artificial” colonic microbiota delivered by PolyFermS continuous fermentation models can provide a controllable and reproducible alternative to fecal transplantation, but effective preservation strategies must be developed. In this study, we systematically investigated the response of sessile and planktonic artificial colonic microbiota to cryopreservation and lyophilization. We suggest that functional redundancy is an important factor in providing functional stability with respect to exposure to stress during processing and storage. Functional redundancy in compositionally reduced microbial systems may be considered when designing microbial products for therapy.

Distinct capabilities of different Gammaproteobacterial strains on utilizing small peptides in seawater

Proteins and peptides account for 20–75% of marine biota biomass, of which a major fraction is metabolized by bacteria, thus deciphering interactions between bacteria and peptides is important in understanding marine carbon and nitrogen cycling. To better understand capabilities of different bacterial strains on peptide decomposition, four Gammaproteobacteria (Pseudoalteromonas atlantica, Alteromonas sp., Marinobacterium jannaschii, Amphritea japonica) were incubated in autoclaved seawater amended with tetrapeptide alanine-valine-phenylalanine-alanine (AVFA), a fragment of RuBisCO. While AVFA was decomposed greatly by Pseudoalteromonas atlantica and Alteromonas sp, it remained nearly intact in the Marinobacterium jannaschii and Amphritea japonica incubations. Pseudoalteromonas and Alteromonas decomposed AVFA mainly through extracellular hydrolysis pathway, releasing 71–85% of the AVFA as hydrolysis products to the surrounding seawater. Overall, this study showed that Gammaproteobacterial strains differ greatly in their capabilities of metabolizing peptides physiologically, providing insights into interactions of bacteria and labile organic matter in marine environments.

Fluorescence in situ hybridization (FISH) and cell sorting of living bacteria

Despite the development of several cultivation methods, the rate of discovery of microorganisms that are yet-to-be cultivated outpaces the rate of isolating and cultivating novel species in the laboratory. Furthermore, no current cultivation technique is capable of selectively isolating and cultivating specific bacterial taxa or phylogenetic groups independently of morphological or physiological properties. Here, we developed a new method to isolate living bacteria solely based on their 16S rRNA gene sequence. We showed that bacteria can survive a modified version of the standard fluorescence in situ hybridization (FISH) procedure, in which fixation is omitted and other factors, such as centrifugation and buffers, are optimized. We also demonstrated that labelled DNA probes can be introduced into living bacterial cells by means of chemical transformation and that specific hybridization occurs. This new method, which we call live-FISH, was then combined with fluorescence-activated cell sorting (FACS) to sort specific taxonomic groups of bacteria from a mock and natural bacterial communities and subsequently culture them. Live-FISH represents the first attempt to systematically optimize conditions known to affect cell viability during FISH and then to sort bacterial cells surviving the procedure. No sophisticated probe design is required, making live-FISH a straightforward method to be potentially used in combination with other single-cell techniques and for the isolation and cultivation of new microorganisms.

Effect of NaCl on nitrification performance and extracellular polymeric substance characteristic of Klebsiella sp. TN-10

Klebsiella sp. TN-10, isolated from tannery wastewater, exhibited excellent nitrification ability cultivated in media with NaCl contents ranging from 0 to 35 g/L. Analysis of antioxidative enzyme activities of TN-10 stressed by NaCl showed that the stain produced more superoxide dismutase (SOD) and catalase (CAT) to fight against salt stress conditions. Moreover, the auto-aggregation index of TN-10 decreased with the increment of NaCl contents, which is consistent with results of zeta potentials. Extinction-emission matrix (EEM) and Fourier-transform infrared (FT-IR) spectrum analyses showed that the compositions of extracellular polymeric substances (EPS) by TN-10 after NaCl shock were similar. Furthermore, proteins and polysaccharides were the main components of EPS, and the contents were greatly influenced by salinity. Then, circular dichroism (CD) spectrum was used to calculate the contents of each protein secondary structure. These results provided further insights into the knowledge of nitrification characteristics, auto-aggregation performance, and EPS compositions of TN-10 during NaCl shock.

Characterization of the Fouling Layer on the Membrane Surface in a Membrane Bioreactor: Evolution of the Foulants' Composition and Aggregation Ability

In this study, the characteristics of membrane foulants were analyzed with regard to morphology, composition, and aggregation ability during the three stages of transmembrane pressure (TMP) development (fast-slow-fast rise in TMP) in a steady operational membrane bioreactor (MBR). The results obtained show that the fouling layer at the slow TMP-increase stage possessed a higher average roughness (71.27 nm) and increased fractal dimension (2.33), which resulted in a low membrane fouling rate (0.87 kPa/d). A higher extracellular DNA (eDNA) proportion (26.12%) in the extracellular polymeric substances (EPS) resulted in both higher zeta potential (-23.3 mV) and higher hydrophobicity (82.3%) for initial foulants, which induced and increased the protein proportion in the subsequent fouling layer (74.11%). Furthermore, the main composition of the EPS shifted from protein toward polysaccharide dominance in the final fouling layer. The aggregation test confirmed that eDNA was essential for foulant aggregation in the initial fouling layer, whereas ion interaction significantly affected foulant aggregation in the final fouling layer.

Underestimated Risks of Infantile Infectious Disease from the Caregiver's Typical Handling Practices of Infant Formula

The impact on infant caregiver as a reservoir of pathogens has not been exploited with perspective to powdered infant formula (PIF). Here we reveal novel route of pathogen transfer through hand-spoon-PIF unexpectedly occurred by even typical practices of caregivers, handling of PIF and storage of feeding-spoon in PIF container. Hand-spoon-PIF contamination route was simulated to analyze the transfer and subsequent survival of pathogens. Major pathogens associated with infantile fatal diseases (Cronobacter sakazakii, Salmonella enterica, Staphylococcus aureus) were readily transmitted to PIF from skin (3−6 log CFU/hand) via spoons following long-term survival of transferred pathogens (3 weeks; use-by date of PIF) as the excessive level of infectious dose, highlighting direct onset of diseases. Low bacterial load on skin (ca. 1 log CFU/hand) could prevent cross-contamination of PIF, however, at least 72 h survival of transferred pathogen on spoons demonstrated the probability on re-contamination of PIF. To our knowledge, this is the first study to investigate the cross-contamination of utensils in contact with powdered-foods. Bacterial load on hands is the key determinant of pathogen transfer and the extent of risk are species-dependent. These evidential results redefine risk of caregivers’ practices and facilitate incorporation of cross-contamination into risk-assessment as underestimated route of infection.

In vitro and in silico approaches of antibiofilm activity of 1-hydroxy-1-norresistomycin against human clinical pathogens

In the present study, an attempt has been made to explore the antibiofilm activity of bioactive compound 1-hydroxy-1-norresistomycin (HNM) derived from coral mucus associated actinomycete Streptomyces variabilis. Initially, different concentration of HNM inhibited the biofilm formation of human clinical pathogens Escherichia coli, Vibrio cholerae and Staphylococcus aureus was determined using crystal-violet staining assay. The light microscopic analysis showed that HNM reduced the biofilm formation and adherence of bacterial cells on the surface of coverslip. HNM also damages the 3D architecture with reduced thickness as well as cell aggregation of biofilm forming bacteria analysed by confocal laser scanning microscopy (CLSM). In addition, HNM also demonstrated the efficiency in inhibiting theoretical adhesion by altering the surface hydrophobicity that can potentially hamper cellular adhesion and prevent biofilm formation. Furthermore, the molecular docking showed the significant interaction between HNM and key biofilm forming proteins proved an excellent antibiofilm activity of HNM. Together, these results suggest that the HNM can serve as potential antibiofilm agent in controlling the infections of E. coli, V. cholerae and S. aureus.

Sources of variability in SERS spectra of bacteria: comprehensive analysis of interactions between selected bacteria and plasmonic nanostructures

The surface-enhanced Raman spectroscopy (SERS)-based analysis of bacteria suffers from the lack of a standard SERS detection protocol (type of substrates, excitation frequencies, and sampling methodologies) that could be employed throughout laboratories to produce repeatable and valuable spectral information. In this work, we have examined several factors influencing the spectrum and signal enhancement during SERS studies conducted on both Gram-negative and Gram-positive bacterial species: Escherichia coli and Bacillus subtilis, respectively. These factors can be grouped into those which are related to the structure and types of plasmonic systems used during SERS measurements and those that are associated with the culturing conditions, types of culture media, and method of biological sample preparation.

The Limitations of Collagen/CPP Hybrid Peptides as Carriers for Cancer Drugs to FaDu Cells

The in vitro efficacy of cancer prodrugs varies significantly between malignant cell lines. The most commonly identified problems relate to delivery: uptake mechanism, endosomal entrapment, and drug release. Here we present the study of collagen/cell penetrating hybrid (COL/CPP) peptide carriers intended to deliver paclitaxel to the hypopharyngeal carcinoma (FaDu) cells. Confocal microscopy imaging revealed the surprising response of FaDu cell to COL/CPP in comparison to previously studied cancer cell lines: hybrid peptides that carry both COL and CPP domain adsorb on the FaDu cell surface. While the CPP domain was design to facilitate the cellular uptake, in the case of FaDu cells, it also induced detrimental interactions with the cell membrane. Despite surface adsorption, the colocalization study with endosomal markers EEA1 and LAMP1 reveals that COL/CPP is internalized via endosomal pathway, peptides are able to escape before lysosome formation and release paclitaxel. Therefore, the main obstacle for paclitaxel delivery to FaDu cells appears to be related to cell surface properties. This behavior seems specific to FaDu cells, and could be linked to previously reported overexpression of T5, heparanase splice variants that produces protein lacking enzymatic activity of heparanase. This results in increased concentration of HSPG on FaDu cell surface, and possibly creates a barrier for cellular uptake of highly charged COL/CPP.

Isolation and Nitrogen Removal Characteristics of an Aerobic Heterotrophic Nitrifying-Denitrifying Bacterium, Klebsiella sp. TN-10

Nitrogen removal by microorganisms has attracted increasing attention in wastewater treatment. In the present study, a heterotrophic nitrification bacterium was isolated from tannery wastewater and identified as Klebsiella sp. TN-10 based on phenotypic and phylogenetic characteristics. The optimal conditions for cell growth and nitrogen removal were investigated, and the results showed that the greatest ammonium removal rate and maximum biomass were achieved by using sodium pyruvate (7 g/L) as carbon source, C/N 12, pH 7, and temperature 30 °C. Under optimal conditions, the removal rate of ammonia nitrogen reached 96%. Besides, the growth characteristic and the ability of utilizing nitrate and nitrite were investigated. The results demonstrated that strain TN-10 exhibited excellent characteristics to remove both nitrate and nitrite, with the removal rate of 95.44% and 99.87%, respectively. In addition, the nitrite reductase (NiR) and nitrate reductase (NR) involved in denitrification were both active, with the activities of 0.0815 and 0.0283 U/mg proteins, respectively. Furthermore, the aggregation ability, auto-aggregation kinetics, and the relationship between zeta potentials and flocculating efficiency were determined. These results indicated that the strain Klebsiella sp. TN-10, with efficient heterotrophic nitrification-aerobic denitrification ability, has potential application in wastewater treatment.

Escherichia coli O157:H7 and Salmonella Typhimurium adhesion to spinach leaf surfaces: Sensitivity to water chemistry and nutrient availability

This study investigated the effects of solution chemistry and growth conditions on bacterial deposition on spinach leaf surfaces using a parallel plate flow cell. Two food safety pathogens of concern and two non-pathogen bacterial surrogates (environmental E. coli isolates) were grown in ideal (LB media) and nutrient-restricted (M9 media) conditions. Bacterial attachment was quantified as mass transfer rate coefficients for cells suspended in 10 mM KCl, CaCl₂ and artificial groundwater, and cell and leaf surfaces were extensively characterized (zeta potential, hydrophobicity, extracellular polymer (EPS) composition). Between the pathogens, E. coli O157:H7 attachment was greater than that of Salmonella Typhimurium, attributed to measurable variability in cell surface charge and hydrophobicity. When grown in M9 media, both pathogens were significantly more adhesive to spinach surfaces (p < 0.01) than when grown in LB media. Surrogates did not follow this trend and showed minimal changes in adhesion kinetics and surface properties between growth conditions. EPS sugar/protein ratios were reduced in some of the highest attachment scenarios, suggesting that changes in EPS composition in favor of proteins may play a role. These results show the importance of growth conditions and solution complexities in understanding mechanisms of aqueous bacterial adhesion to food surfaces.

Lessons in Membrane Engineering for Octanoic Acid Production from Environmental Escherichia coli Isolates

Fermentative production of many attractive biorenewable fuels and chemicals is limited by product toxicity in the form of damage to the microbial cell membrane. Metabolic engineering of the production organism can help mitigate this problem, but there is a need for identification and prioritization of the most effective engineering targets. Here, we use a set of previously characterized environmental Escherichia coli isolates with high tolerance and production of octanoic acid, a model membrane-damaging biorenewable product, as a case study for identifying and prioritizing membrane engineering strategies. This characterization identified differences in the membrane lipid composition, fluidity, integrity, and cell surface hydrophobicity from those of the lab strain MG1655. Consistent with previous publications, decreased membrane fluidity was associated with increased fatty acid production ability. Maintenance of high membrane integrity or longer membrane lipids seemed to be of less importance than fluidity. Cell surface hydrophobicity was also directly associated with fatty acid production titers, with the strength of this association demonstrated by plasmid-based expression of the multiple stress resistance outer membrane protein BhsA. This expression of bhsA was effective in altering hydrophobicity, but the direction and magnitude of the change differed between strains. Thus, additional strategies are needed to reliably engineer cell surface hydrophobicity. This work demonstrates the ability of environmental microbiological studies to impact the metabolic engineering design-build-test-learn cycle and possibly increase the economic viability of fermentative bioprocesses.IMPORTANCE The production of bulk fuels and chemicals in a bio-based fermentation process requires high product titers. This is often difficult to achieve, because many of the target molecules damage the membrane of the microbial cell factory. Engineering the composition of the membrane in order to decrease its vulnerability to this damage has proven to be an effective strategy for improving bioproduction, but additional strategies and engineering targets are needed. Here, we studied a small set of environmental Escherichia coli isolates that have higher production titers of octanoic acid, a model biorenewable chemical, than those of the lab strain MG1655. We found that membrane fluidity and cell surface hydrophobicity are strongly associated with improved octanoic acid production. Fewer genetic modification strategies have been demonstrated for tuning hydrophobicity relative to fluidity, leading to the conclusion that there is a need for expanding hydrophobicity engineering strategies in E. coli.

Influence of inhibitors on the adhesion of SRB to the stainless steel in circulating cooling water

Influence of the surface characteristics of three stainless steels (SS304, 316L and 317) and presence of scale inhibitors on adhesion kinetics of sulfate reducing bacteria (SRB) in circulating cooling water, were investigated by evaluating surface free energy, adhesion kinetic constants in a parallel plate flow chamber. Results show that the surface free energy values of SS317, SS316L and SS304 are -31.69, -24.18 and -13.92 mJ m^-2, respectively. SS317 surface had higher surface hydrophobicity than SS316L and SS304. In the process of bacteria cells adhesion onto SS surfaces, electrostatic interaction for SS is slightly more than hydrophobic interaction. The number of adhering bacteria and the adhesion kinetic constants are different on the three types of stainless steel. The adhesion kinetic constants for SS317 and 316L are greater than that for SS304, which are 0.0354, 0.0282 and 0.0190 min^-1, respectively. Scale inhibitors of hydrosy ethyl fork phosphonic acid (HEDP) and phosphono butane-1, 2, 4-tricarboxylic acid (PBTCA) have a certain influence on the initial adhesion of bacteria cell and adhesion kinetics constants are reduced in the presence of HEDP and PBTCA.

Low-level concentrations of aminoglycoside antibiotics induce the aggregation of cyanobacteria

The interactions between antibiotics and microorganisms have attracted enormous research attentions. In this study, we investigated the effects of two typical aminoglycoside antibiotics on the aggregation of the model cyanobacterium, Synechococcus elongatus, and the dominating strain in algal blooms, Microcystis aeruginosa, via the analysis of zeta potentials, hydrophobicity, and extracellular polymeric substances (EPS) secretion. The results showed that low-level antibiotics promoted the aggregation of S. elongatus and M. aeruginosa by 40 and 18% under 0.10 and 0.02 μg/mL of kanamycin, respectively, which was mainly attributed to the combined effects of increased zeta potentials and the ratio between extracellular proteins and polysaccharides. Tobramycin exerted similar effects. Additionally, we discovered that at low pH (pH 5) and ionic strength (1 mM Na⁺ and 2 mM Mg²⁺), the inducing effects of antibiotics would be even larger than those with higher pH and ionic strength. As aggregation is important to cyanobacteria in either the basic physiology of biofilm formation or the algal bloom, our study demonstrated that low-level antibiotics exert ecological impacts via interfered aggregation. We believe this study will shed light on the mechanisms underlying antibiotic-induced biofilm formation and help with the evaluation of the environmental and ecological risks of antibiotics and other emerging pollutants.

Characterization of biofilm-forming capacity and resistance to sanitizers of a range of E. coli O26 pathotypes from clinical cases and cattle in Australia

BACKGROUND

The formation of biofilms and subsequent encasement of bacterial cells in a complex matrix can enhance resistance to antimicrobials and sterilizing agents making these organisms difficult to eradicate and control. The aim of this study was to evaluate and compare the capacity of 40 E. coli O26 isolates of enterohemorrhagic E. coli (EHEC, n = 27), potential EHEC (pEHEC, n = 3), atypical enteropathogenic E. coli (aEPEC, n = 8) and non-toxigenic E. coli (NTEC, n = 2) from human and cattle sources to form biofilms on different surfaces, and determine whether extracellular matrix (ECM) components (cellulose, curli), motility, prophage insertion in mlrA and cell surface hydrophobicity could influence biofilm formation. Finally, the influence of biofilm formation on the sensitivity of isolates to quaternary ammonium compounds (QACs; Profoam, Kwiksan 22) and peracetic acid-based sanitizer (Topactive Des.) for 2 min on polystyrene plate were also evaluated.

RESULTS

Biofilm production on one surface may not indicate biofilm formation on a different surface. Biofilm was formed by different pathotypes on polystyrene (70%), stainless steel (87.5%) and glass slides (95%), however only 50% demonstrated pellicle formation. EHEC isolates were significantly more likely to form a pellicle at the air-liquid interface and biofilms on polystyrene surface at 48 h than aEPEC. Strains that don't produce ECM (curli or cellulose), harbor a prophage insertion in mlrA, and are non-motile have lower biofilm forming capacities than those isolates possessing combinations of these attributes. Hydrophobicity had no impact on biofilm formation. After 2 min exposure, none of the disinfectants tested were able to completely inactivate all cells within a biofilm regardless of pathotypes and the amount of biofilm formed.

CONCLUSION

Pathotypes of E. coli O26 showed varying capacities to form biofilms, however, most EHEC strains had the capacity to form biofilm on all surfaces and at the air-liquid interface under the conditions used in this study. Biofilms provided a protective effect to E. coli O26 strains against the three sanitizers, previously shown to successfully control the growth of their planktonic counterparts. Whether the characteristics of biofilm forming and non-biofilm forming strains observed in this study reflect their attributes within the food and meat-processing environments is unknown. Further studies that represent the food and meat-processing environments are required.

Escherichia coli attachment to model particulates: The effects of bacterial cell characteristics and particulate properties

E. coli bacteria move in streams freely in a planktonic state or attached to suspended particulates. Attachment is a dynamic process, and the fraction of attached microorganisms is thought to be affected by both bacterial characteristics and particulate properties. In this study, we investigated how the properties of cell surfaces and stream particulates influence attachment. Attachment assays were conducted for 77 E. coli strains and three model particulates (ferrihydrite, Ca-montmorillonite, or corn stover) under environmentally relevant conditions. Surface area, particle size distribution, and total carbon content were determined for each type of particulate. Among the three particulates, attachment fractions to corn stover were significantly larger than the attachments to 2-line ferrihydrite (p-value = 0.0036) and Ca-montmorillonite (p-value = 0.022). Furthermore, attachment to Ca-montmorillonite and corn stover was successfully modeled by a Generalized Additive Model (GAM) using cell characteristics as predictor variables. The natural logarithm of the net charge on the bacterial surface had a significant, positive, and linear impact on the attachment of E. coli bacteria to Ca-montmorillonite (p-value = 0.013), but it did not significantly impact the attachment to corn stover (p-value = 0.36). The large diversities in cell characteristics among 77 E. coli strains, particulate properties, and attachment fractions clearly demonstrated the inadequacy of using a static parameter or linear coefficient to predict the attachment behavior of E. coli in stream water quality models.

Centrifuge separation effect on bacterial indicator reduction in dairy manure

Centrifugation is a commonly applied separation method for manure processing on large farms to separate solids and nutrients. Pathogen reduction is also an important consideration for managing manure. Appropriate treatment reduces risks from pathogen exposure when manure is used as soil amendments or the processed liquid stream is recycled to flush the barn. This study investigated the effects of centrifugation and polymer addition on bacterial indicator removal from the liquid fraction of manure slurries. Farm samples were taken from a manure centrifuge processing system. There were negligible changes of quantified pathogen indicator concentrations in the low-solids centrate compared to the influent slurry. To study if possible improvements could be made to the system, lab scale experiments were performed investigating a range of g-forces and flocculating polymer addition. The results demonstrated that polymer addition had a negligible effect on the indicator bacteria levels when centrifuged at high g forces. However, the higher g force centrifugation was capable of reducing bacterial indicator levels up to two-log₁₀ in the liquid stream of the manure, although at speeds higher than typical centrifuge operations currently used for manure processing applications. This study suggests manure centrifuge equipment could be redesigned to provide pathogen reduction to meet emerging issues, such as zoonotic pathogen control.