Sustainable Biopolymer-Based Electrochemical Sensors for Trace Heavy Metal Determination in Water: A Comprehensive Review

The growing concern over heavy metal contamination in environmental and industrial settings has intensified the need for sensitive, selective, and cost-effective detection technologies. Electrochemical sensors, due to their high sensitivity, rapid response, and portability, have emerged as promising tools for detecting heavy metals. Recent years have seen significant progress in utilizing biopolymer-based materials to enhance the performance of these sensors. Biopolymers, derived from renewable raw materials, have garnered considerable interest in both science and industry. These biopolymer-based composites are increasingly recognized as superior alternatives to conventional non-biodegradable materials because of their ability to degrade through environmental exposure. This review provides a comprehensive overview of recent advancements in biopolymer-based electrochemical sensors for heavy metal detection. It discusses various types of biopolymers and bio-sourced polymers, their extraction methods, and chemical properties. Additionally, it highlights the state of the art in applying biopolymers to electrochemical sensor development for heavy metal detection, synthesizing recent advances and offering insights into design principles, fabrication strategies, and analytical performance. This review underscores the potential of biopolymer-based sensors as cost-effective, eco-friendly, and efficient tools for addressing the pressing issue of heavy metal contamination in water and discusses their advantages and limitations. It also outlines future research directions to further enhance the performance and applicability of these sensors.

Green synthesis of multifunctional natural rubber-lignin nanocomposites: A sustainable approach for waste reduction

Lignin, a valuable biomaterial having an array of exciting properties is increasingly favoured as a reinforcement material in the fabrication of green composites. Reinforcement in biopolymers like natural rubber (NR) using lignin nanoparticles (LNP) is considered a hotspot today. In this study, LNP synthesized via the homogenization method was incorporated into natural rubber latex (NRL) using probe sonication, and NR/Lignin nanocomposites (NR/LNP) were fabricated using latex dipping method. The addition of LNP resulted in significant enhancements in mechanical and antibacterial properties, biodegradability, and ultraviolet (UV) blocking capabilities with the addition of 7 parts per hundred rubber (phr) of LNP, due to the uniform dispersion and effective interaction between NR and LNP. This research demonstrates a versatile pathway for integrating LNP into NR through a green method, enabling the production of eco-friendly NR nanocomposites for multifunctional applications. This pathway contributes to a safe disposal of NR based products.

Advances in lignin-based biosorbents for sustainable wastewater treatment

The heavy metals, pesticides and dyes in agriculture and industry caused serious water pollution have increased the urgency for the advancement of biomass-based adsorbents due to their merits of low cost, high efficiency, and environmental sustainability. Thus, this review systematically examines the recent progress of lignin-based adsorbents dedicated to wastewater purification. Commencing with a succinct exposition on the intricate structure and prevalent forms of lignin, the review proceeds to expound rational design strategies tailored for lignin-based adsorbents coupled with adsorption mechanisms and regeneration methods. Emphasis is placed on the potential industrial applications of lignin-based adsorbents, accentuating their capacity for recovery and direct utilization post-use. The future challenges and outlooks associated with lignin-based adsorbents are discussed to provide novel perspectives for the development of high-performance and sustainable biosorbents, facilitating the effective removal of pollutants and the value-added utilization of resources in a sustainable manner.

A sustainable and eco-friendly approach for environmental and energy management using biopolymers chitosan, lignin and cellulose - A review

Biopolymers are a naturally occurring alternative to synthetic polymers that are linked by covalent bonds, which includes cellular components such as proteins, nucleotides, lipids, and polysaccharides. Based on the extensive literature review it was found that chitosan, lignin, and cellulose were predominantly used in the energy and environmental sectors. Due to their vast array of qualities, including the adsorption, flocculation, anticoagulation, and furthermore, have made them useful for treating wastewater and pollutant removal. Chitosan and lignin have been used as a proton exchange membrane in the energy storage device of fuel cells. As these biopolymers develop strong coordination connections with metal surfaces, they act as an anticorrosive agent, which inhibiting the corrosion. Besides, there are a lot of recent developments in the application of biopolymers for energy and environmental fields. The present review provides a concise summary of recent developments in membrane-based biopolymers role in energy and environmental field. In addition, this review is drawn to a conclusion with a discussion of future trends in the real application of biopolymers in a variety of different industries, as well as the financial significance of these future trends.

Pollutants in aquatic system: a frontier perspective of emerging threat and strategies to solve the crisis for safe drinking water

Water is an indispensable natural resource and is the most vital substance for the existence of life on earth. However, due to anthropogenic activities, it is being polluted at an alarming rate which has led to serious concern about water shortage across the world. Moreover, toxic contaminants released into water bodies from various industrial and domestic activities negatively affect aquatic and terrestrial organisms and cause serious diseases such as cancer, renal problems, gastroenteritis, diarrhea, and nausea in humans. Therefore, water treatments that can eliminate toxins are very crucial. Unfortunately, pollution treatment remains a difficulty when four broad considerations are taken into account: effectiveness, reusability, environmental friendliness, and affordability. In this situation, protecting water from contamination or creating affordable remedial techniques has become a serious issue. Although traditional wastewater treatment technologies have existed since antiquity, they are both expensive and inefficient. Nowadays, advanced sustainable technical approaches are being created to replace traditional wastewater treatment processes. The present study reviews the sources, toxicity, and possible remediation techniques of the water contaminants.

Surface engineered functional biomaterials for hazardous pollutants removal from aqueous environment

The issue of water contamination by heavy metal ions as highly persistent pollutants with harmful influence primarily on biological systems, even in trace levels, has become a great environmental concern globally. Therefore, there is a need for the use of highly sensitive techniques or preconcentration methods for the removal of heavy metal ions at trace levels. Thus, this research investigates a novel approach by examining the possibility of using pomegranate (Punica granatum) peel layered material for the simultaneous preconcentration of seven heavy metal ions; Cd(II), Co(II), Cr(III), Cu(II), Mn(II), Ni(II) and Pb(II) from aqueous solution and three river water samples. The quantification of the heavy metals was performed by the means of FAAS technique. The characterization of biomaterial was performed by SEM/EDS, FTIR analysis and pHpzc determination before and after the remediation process. The reusability study, as well as the influence of interfering ions (Ca, K, Mg, Na and Zn) were evaluated. The conditions of preconcentration by the column method included the optimization of solution pH (5); flow rate (1.5 mL/min), a dose of biosorbent (200 mg), type of the eluent (1 mol/L HNO₃), sample volume (100 mL) and sorbent fraction (<0.25 mm). The biosorbent capacity ranged from 4.45 to 57.70 μmol/g for the investigated heavy metals. The practical relevance of this study is further extended by novel data regarding adsorbent cost analysis (17.49 $/mol). The Punica granatum sorbent represents a highly effective and economical biosorbent for the preconcentration of heavy metal ions for possible application in industrial sectors.

Glutathione primed seed improved lead-stress tolerance in Brassica rapa L. through modulation of physio-biochemical attributes and nutrient uptake

Heavy metal toxicity is a major environmental issue that affects all life forms, including plants. The accumulation of lead (Pb) in agricultural soils is a significant contributor to reduced crop yields, and it poses serious health risks to people who consume lead-contaminated agricultural products. The current study was undertaken to investigate the beneficial effects of glutathione (GSH) on the amelioration of stress induced by Pb (300 mg kg-1 Pb) in Brassica rapa L. (turnip). For this purpose, B. rapa seeds primed with 25, 50, and 75 µmol L-1. The root and shoot length, seedling biomass, and leaf area, was reduced under Pb stress. Lead toxicity inhibited the net photosynthetic rate (31.36%), total chlorophyll content (74.54%) of B. rapa plants in comparison to control. Lead-stressed plants additionally exhibited changes in proline levels, as well as lower levels of total soluble protein and phenolic content. Nevertheless, seed priming with GSH resulted in higher concentrations of the nutritional content (Mg+2, Zn+2, Na+, K+) that increased Pb stress tolerance. The GSH2 treated seed enhanced the photosynthetic rate (46.34%), stomatal conductance (80.55%), and transpiration rate (53.125%) over Pb stress. Furthermore, GSH2 enhanced total soluble proteins (37.75%), phenolic content (58.38%), and DPPH (1.5fold) of turnip plant over control seedlings. According to our research, GSH2 primed B. rapa seed demonstrated a reduction in Pb toxicity, which could be used to help seedling establishment in soils contaminated with Pb.

High capacity and fast removal of Cr(vi) by alkali lignin-based poly(tetraethylene pentamine-pyrogallol) sorbent

In this work, a novel alkali lignin-based adsorption material, alkali lignin-based poly(tetraethylene pentamine-pyrogallol) (AL-PTAP), was prepared using a Mannich reaction and catechol-amine reaction for removal of Cr(vi). It was characterized by thermogravimetric analysis (TGA), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS). The effects of tetraethylene pentamine (TEPA) dosage, pyrogallol (PL) dosage, contact time, pH, temperature and other factors on the adsorption behavior of the adsorbent were systematically investigated. These experimental data show that the adsorption behavior conforms to the pseudo-second-order kinetic model and the Langmuir isotherm model. The maximum adsorption capacity is 769.2 mg g-1 at 303 K, which is much higher than that of alkali lignin (AL). AL-PTAP can achieve a removal rate of almost 100% for Cr(vi) solutions with a concentration of less than 90 mg L-1 at 1 min. Furthermore, the toxic Cr(vi) is partly reduced to nontoxic Cr(iii) during the adsorption process. Therefore, AL-PTAP is a fast and efficient alkali lignin-based adsorbent, which is expected to improve the utilization value of alkali lignin in Cr(vi) wastewater treatment.

Nanocellulose-Based Adsorbents for Heavy Metal Ion

Heavy metal ions in industrial sewage constitute a serious threat to human health. Nanocellulose-based adsorbents are emerging as an environmentally friendly material platform for heavy metal ion removal based on their unique properties, which include high specific surface area, excellent mechanical properties, and biocompatibility. In this review, we cover the most recent works on nanocellulose-based adsorbents for heavy metal ion removal and present an in-depth discussion of the modification technologies for nanocellulose in the process of assembling high-performance heavy ion adsorbents. By introducing functional groups, such as amino, carboxyl, aldehyde, and thiol, the assembled nanocellulose-based adsorbents both remove single heavy metal ions and can selectively adsorb multiple heavy ions in water. Finally, the remaining challenges of nanocellulose-based adsorbents are pointed out. We anticipate that this review will provide indispensable guidance on the application of nanocellulose-based adsorbents for the removal of heavy metal ions.

Synthesis and Characterization of Thermally Stable Lignosulfonamides

Lignin, a highly aromatic macromolecule building plant cells, and cellulose are two of the most commonly occurring natural polymers. Lignosulfonate is a grade of technical lignin, obtained as a by-product in the paper and wood pulping industries, a result of the used lignin isolation method, i.e., sulfite process. In this work, sodium lignosulfonate is used as a starting material to manufacture sulfonamide derivatives of lignin in a two-step modification procedure. Since this direction of the lignin modification is rather rarely investigated and discussed, it makes a good starting point to expand the state of knowledge and explore the properties of lignosulfonamides. Materials obtained after modification underwent characterization by FTIR, SS-NMR, WAXD, SEM, and TGA. Spectroscopic measurements confirmed the incorporation of dihexylamine into the lignin structure and the formation of lignosulfonamide. The crystalline structure of the material was not affected by the modification procedure, as evidenced by the WAXD, with only minute morphological changes of the surface visible on the SEM imaging. The obtained materials were characterized by improved parameters of thermal stability in relation to the raw material. As-prepared sulfonamide lignin derivatives with a potential application as a filler in biopolymeric composites may become a new class of functional, value-added, sustainable additives.

Chitosan-Hydroxyapatite Bio-Based Composite in Film Form: Synthesis and Application in Wastewater

Water purification from toxic metals was the main objective of this work. A composite in film form was prepared from the biomaterials hydroxyapatite, chitosan and glycerol using the dissolution/recrystallization method. A nanoparticle-based film with a homogenous and smooth surface was produced. The results of total reflectance infrared spectroscopy (ATR-FTIR) and thermal gravimetric analysis (TGA/DTA) demonstrated the presence of a substantial physical force between composite components. The composite was tested for its ability to absorb Cd2+ and Zn2+ ions from aqueous solutions. Cd2+ and Zn2+ adsorption mechanisms are fit using the Langmuir model and the pseudo-second-order model. Thermodynamic parameters indicated that Cd2+ and Zn2+ ion adsorption onto the composite surface is spontaneous and preferred at neutral pH and temperatures somewhat higher than room temperature. The adsorption studies showed that the maximum adsorption capacity of the HAp/CTs bio-composite membrane for Cd2+ and Zn2+ ions was in the order of cadmium (120 mg/g) > Zinc (90 mg/g) at an equilibrium time of 20 min and a temperature of 25 °C. The results obtained on the physico-chemical properties of nanocomposite membranes and their sorption capacities offer promising potential for industrial and biological activities.

Modified Polymeric Biosorbents from Rumex acetosella for the Removal of Heavy Metals in Wastewater

The contamination of water resources by effluents from various industries often contains heavy metals, which cause irreversible damage to the environment and health. The objective was to evaluate different biosorbents from the weed Rumex acetosella to remove metal cations in wastewater. Drying, grinding and sieving of the stems was carried out to obtain the biomass, retaining the fractions of 250 to 500 µm and 500 to 750 µm, which served to obtain the biosorbents in natura (unmodified), acidic, alkaline, and mixed. Proximal analysis, PZC, TOC, removal capacity, influence of pH, functional groups, thermal analysis, structural characteristics, adsorption isotherms, and kinetic study were evaluated. The 250 µm mixed treatment was the one that presented the highest removal percentages, mainly due to the OH, NH, -C-H, COOH, and C-O functional groups achieving the removal of up to 96.14% of lead, 36.30% of zinc, 34.10% of cadmium and 32.50% of arsenic. For contact times of 120 min and an optimum pH of 5.0, a loss of cellulose mass of 59% at 328 °C and a change in the surface of the material were also observed, which allowed for obtaining a topography with greater chelating capacity, and the Langmuir and pseudo-second order models were better fitted to the adsorption data. The new biosorbents could be used in wastewater treatment economically and efficiently.

Phytoremediation of pollutants from wastewater: A concise review

As there is a global water crisis facing the whole world, it is important to find alternative solutions to treat wastewater for reuse. Hence, plants have an effective role in removing pollutants from wastewater, which has been emphasized in this review article. Biological treatment of wastewater can be considered an eco-friendly and cost-effective process that depends on in the future. Living organisms, including plants, can remediate pollutants in wastewater, especially in agricultural fields, such as dyes, heavy metals, hydrocarbons, pharmaceuticals, and pesticides. This review discusses the different activities of plants in pollutant elimination from wastewater and sheds light on the utilization of plants in this scope. This review focuses on the remediation of the most common contaminants present in wastewater, which are difficult to the removal with microorganisms, such as bacteria, fungi, and algae. Moreover, it covers the major role of plants in wastewater treatment and the potential of phytoremediation as a possible solution for the global water crisis.

Agricultural waste management strategies for environmental sustainability

Globally, abundant agricultural wastes (AWs) are being generated each day to fulfil the increasing demands of the fast-growing population. The limited and/or improper management of the same has created an urgent need to devise strategies for their timely utilization and valorisation, for agricultural sustainability and human-food and health security. The AWs are generated from different sources including crop residue, agro-industries, livestock, and aquaculture. The main component of the crop residue and agro-industrial waste is cellulose, (the most abundant biopolymer), followed by lignin and hemicellulose (lignocellulosic biomass). The AWs and their processing are a global issue since its vast majority is currently burned or buried in soil, causing pollution of air, water and global warming. Traditionally, some crop residues have been used in combustion, animal fodder, roof thatching, composting, soil mulching, matchsticks and paper production. But, lignocellulosic biomass can also serve as a sustainable source of biofuel (biodiesel, bioethanol, biogas, biohydrogen) and bioenergy in order to mitigate the fossil fuel shortage and climate change issues. Thus, valorisation of lignocellulosic residues has the potential to influence the bioeconomy by producing value-added products including biofertilizers, bio-bricks, bio-coal, bio-plastics, paper, biofuels, industrial enzymes, organic acids etc. This review encompasses circular bioeconomy based various AW management strategies, which involve 'reduction', 'reusing' and 'recycling' of AWs to boost sustainable agriculture and minimise environmental pollution.

Recent Advances in Bio-Based Additive Flame Retardants for Thermosetting Resins

Thermosetting resins are used in many applications due to their great mechanical properties, chemical resistance, and dimensional stability. However, the flammability of thermosets needs to be improved to minimize fire risk and meet fire safety regulations. Some commercially available flame retardants have an adverse effect on people’s health and the environment. Thus, the development of novel, more sustainable flame retardants obtained or derived from biomass has become an objective of contemporary research. The objective of this study is to summarize recent progress on bio-based flame retardants for thermosetting resins so as to promote their prompt development. Groups of biomass compounds with a potential for flame retardant industrial applications were introduced, and their thermal degradation was investigated. The authors focused mostly on the thermal degradation of composites containing bio-based flame retardants determined by thermogravimetric analysis, their tendency to sustain a flame determined by a limiting oxygen index, and fire behavior determined by a cone calorimeter test. The results showed that the mode of action is mostly based on the forming of the char layer. However, in many cases, there is still a necessity to input a high amount of additive to achieve significant flame retardancy effects, which may adversely impact mechanical properties.

Pitahaya Fruit (Hylocereus spp.) Peels Evaluation for Removal of Pb(II), Cd(II), Co(II), and Ni(II) from the Waters

The present study investigated the performance of Pitahaya (Hylocereus spp.) peel (PP) as a low-cost biosorbent in the removal of Co(II), Cd(II), Pb(II), and Ni(II) from single and multi-component solutions. The characterization of the samples was carried out by pHpzc, Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS). Biosorption was carried out by batch experimental procedure to examine the effects of contact time, solution pH, initial concentration of metal ions, and biosorbent dosage. The results indicate that the biosorption of Pb(II), Cd(II), Co(II), and Ni(II) Pitahaya peels followed pseudo-second-order kinetics, and equilibrium adsorption followed the Langmuir model. The maximum sorption capacities of PP for the metallic species were found to be as follows: Pb (82.64 mg g−1) > Cd (17.95 mg g−1) > Co (6.013 mg g−1) > Ni (5.322 mg g−1). However, the efficiency of the biosorption change when the metallic species are mixed. The re-generation of the PP after the adsorption of the metallic species was done using 0.1 M HNO3 solution, and the reusability of the biomass was carried out using two adsorption and desorption cycles.

Lignocellulosic Materials Used as Biosorbents for the Capture of Nickel (II) in Aqueous Solution

Four lignocellulosic materials (walnut shell, chestnut shell, pine wood and burnt pine wood) were analyzed as biosorbents to remove nickel ions in aqueous solution. The optimal pH condition was determined. Due to this, a range of different pHs (3.0 to 7.5) was tested. The adsorption isotherms and kinetics were established. To plot Langmuir and Freundlich isotherms, batch adsorption tests were made with variable nickel concentrations (5 to 200 mg L−1). The pseudo-first order, pseudo-second order, Elovich and intraparticle diffusion models were used to describe the kinetics, batch adsorption tests were carried out with 25 mg L−1 of nickel solution and agitation time varied from 10 to 1440 min. The specific surface area of the different materials was between 3.97 and 4.85 m2g−1 with the exception for wood with 1.74 m2g−1. The pore size was 26.54 nm for wood and varied between 5.40 and 7.33 nm for the remaining materials. The diffractograms analysis showed that all the lignocellulosic materials presented some crystalline domains with the exception of burnt pine wood which was completely amorphous. The best pH was found to be around 5.0. At this pH the adsorption was higher for chestnut shells, walnut shells, burnt pine wood and wood, respectively. All samples fitted the Langmuir model well, with R2 of 0.994 to 0.998. The sorption kinetics was well described by the pseudo-second order equation with R2 between 0.996 and 1.00. No significative differences on the surface of the materials before and after adsorption could be observed by SEM. Finally, all materials tested were able to remove nickel ions in aqueous solution.

Nanocellulose-Based Materials for Water Treatment: Adsorption, Photocatalytic Degradation, Disinfection, Antifouling, and Nanofiltration

Nanocelluloses are promising bio-nano-materials for use as water treatment materials in environmental protection and remediation. Over the past decades, they have been integrated via novel nanoengineering approaches for water treatment processes. This review aims at giving an overview of nanocellulose requirements concerning emerging nanotechnologies of waster treatments and purification, i.e., adsorption, absorption, flocculation, photocatalytic degradation, disinfection, antifouling, ultrafiltration, nanofiltration, and reverse osmosis. Firstly, the nanocellulose synthesis methods (mechanical, physical, chemical, and biological), unique properties (sizes, geometries, and surface chemistry) were presented and their use for capturing and removal of wastewater pollutants was explained. Secondly, different chemical modification approaches surface functionalization (with functional groups, polymers, and nanoparticles) for enhancing the surface chemistry of the nanocellulose for enabling the effective removal of specific pollutants (suspended particles, microorganisms, hazardous metals ions, organic dyes, drugs, pesticides fertilizers, and oils) were highlighted. Thirdly, new fabrication approaches (solution casting, thermal treatment, electrospinning, 3D printing) that integrated nanocelluloses (spherical nanoparticles, nanowhiskers, nanofibers) to produce water treatment materials (individual composite nanoparticles, hydrogels, aerogels, sponges, membranes, and nanopapers) were covered. Finally, the major challenges and future perspectives concerning the applications of nanocellulose based materials in water treatment and purification were highlighted.

Effect of alkaline lignin on immobilization of cadmium and lead in soils and the associated mechanisms

Lignin is a low-cost and environmental-friendly material and could increase the solubility of phosphorus (P) in soils. Meanwhile, application of P compounds to soils decreases the bioavailability of heavy metals. However, there are few reports on whether lignin-induced P release immobilizes heavy metals in soil. This study investigated this possibility by adding alkaline lignin to forest, paddy and upland soils differing in pH and available P. The amendment of alkaline lignin increased soil P availability and enhanced the adsorption and decreased the desorption percentages of Cd in acid forest and paddy soils. The P released from the soil could immobilize Pb and Cd but the presence of Pb decreased the adsorption capacity of Cd on the acid soils. In comparison, the alkaline lignin decreased Cd adsorption and raised Cd desorption in the alkaline upland soil, due to the formation of soluble complex of hydrophilic organic matter with Cd. In addition, precipitation, complexion, and competition effect among Cd, P and lignin in different soils led to various P concentrations in the experiment. The study suggests that alkaline lignin was effective in Cd/Pb immobilization partly via enhanced P availability in acid soils, but was ineffective in Cd immobilization in alkaline soils.

Synthesis and physiochemical performances of PVC-sodium polyacrylate and PVC-sodium polyacrylate-graphite composite polymer membrane

Three types (type-A, B, and C) of composite polymeric membranes (CPMs) based on poly vinyl chloride (PVC) and different fillers (sodium polyacrylate and sodium polyacrylate-graphite) soaked in water and 0.5 N HCl were prepared using solvent casting method. Different physicochemical parameters such as microscopic surface study, water uptake, perpendicular swelling, density, porosity (ε), ion exchange capacity, and conductivity of the as the prepared CPMs were evaluated. Interestingly, type-A CPM cast with filler-A has greater values of the above parameters except density and ionic conductivity than those of type-B and C CPMs. The water uptake of type-A, B and C composite membranes was respectively in the range of 220.42–534.70, 59.64–41.65, and 15.94–2.62%. Ion exchange capacity of type-A, B and C CPMs was in the range of 3.669 × 107–2.156 × 107, 5.948 × 107–1.258 × 107, and 1.454 × 107–1.201 × 107 m.eq.g−1 respectively while the conductivity order was type-A < B < C. These types of CPMs may be helpful in many applications including proton exchange membranes, fuel cell like devices, as sensors for different metals, gas purification, water treatment, and battery separators.

Lignin Nanoparticles: A Promising Tool to Improve Maize Physiological, Biochemical, and Chemical Traits

Lignin, and its derivatives, are the subject of current research for the exciting properties shown by this biomass. Particularly attractive are lignin nanoparticles for their eco- and biocompatibility compared to other nanomaterials. In this context, the effect of nanostructured lignin microparticles (LNP), obtained from alkaline lignin by acid treatment, on maize plants was investigated. To this end, maize seeds were primed with LNP at five concentrations: 80 mg L-1 (T80), 312 mg L-1 (T312), 1250 mg L-1 (T1250), 5000 mg L-1 (T5000) and 20,000 mg L-1 (T20000). Concerning the dose applied, LNP prompted positive effects on the first stages of maize development (germination and radicle length). Furthermore, the study of plant growth, biochemical and chemical parameters on the developed plants indicated that concerning the dose applied. LNP stimulated beneficial effects on the seedlings (fresh weight and length of shoots and roots). Besides, specific treatments increased the content of chlorophyll (a and b), carotenoid, and anthocyanin. Finally, the soluble protein content showed a positive trend in response to specific dosages. These effects are significant, given the essential biological function performed by these biomolecules. In conclusion, this research indicates as the nanostructured lignin microparticles can be used, at appropriate dosages, to induce positive biological responses in maize. This beneficial action deserves attention as it candidates LNP for biostimulating a crop through seed priming.

Recent progress in preparation and applications of chitosan/calcium phosphate composite materials

Studying the development of unique materials from sustainable and renewable resources has gained increasing concern due to the depletion of fossil resources. Chitosan and its derivatives have been considered as versatile candidates for preparing attractive materials. The fabrication of chitosan/calcium phosphate composite compounds has received much attention for the development of numerous promising products in different fields. In this short review, recent preparation strategies for chitosan/calcium phosphate composites such as freeze casting, vacuum-assisted filtration, and biomimetic mineralization were discussed. The review presented their advances for diverse applications such as bone tissue engineering implants, drug delivery, wound healing, dental caries, as well adsorption of organic and heavy metals from polluted water. The challenges and future perspectives for the application of chitosan/calcium phosphate materials in biomedical and environmental applications were also involved in this review article.

Kinetics, equilibrium and thermodynamics of dyes adsorption onto modified chitosan: a review

In view of promising sorption capacity, stability, biodegradability, cost-effectiveness, environmental friendly nature, regeneration and recycling ability, the chitosan (CS) based adsorbents are highly efficient for the sequestration of dyes. Since CS offers variable chemical structures and CS have been modified by incorporating different moieties. The CS composites with unique properties have been employed successfully for dye adsorption with reasonably high adsorption capacity versus other similar adsorbents. Modifications of CS were promising for the preparation of composites that are extensively studied for their adsorption capacities for various dyes. This review highlights the CS and its modification and their applications for the adsorption of dyes. The removal capacities of CS-based adsorbents, equilibrium modeling, kinetics studies and the thermodynamic characteristics are reported. Moreover, the FTIR, BET, SEM, TGA and XRD were employed for the characterization of CS modified adsorbents are also discussed. Results revealed that the modified CS is highly efficient and can be employed for the sequestration of dyes from effluents.

Kinetics, equilibrium and thermodynamics of dyes adsorption onto modified chitosan: a review

In view of promising sorption capacity, stability, biodegradability, cost-effectiveness, environmental friendly nature, regeneration and recycling ability, the chitosan (CS) based adsorbents are highly efficient for the sequestration of dyes. Since CS offers variable chemical structures and CS have been modified by incorporating different moieties. The CS composites with unique properties have been employed successfully for dye adsorption with reasonably high adsorption capacity versus other similar adsorbents. Modifications of CS were promising for the preparation of composites that are extensively studied for their adsorption capacities for various dyes. This review highlights the CS and its modification and their applications for the adsorption of dyes. The removal capacities of CS-based adsorbents, equilibrium modeling, kinetics studies and the thermodynamic characteristics are reported. Moreover, the FTIR, BET, SEM, TGA and XRD were employed for the characterization of CS modified adsorbents are also discussed. Results revealed that the modified CS is highly efficient and can be employed for the sequestration of dyes from effluents.

REALITIES AND PROSPECTS OF FUTURE COMPLEX PROCESSING OF PLANT RAW MATERIALS INTO BIOTHETANOL AND BY-PRODUCTS

The use of plant biomass as a primary source of energy is currently unacceptable both from an economic and environmental point of view. The experience of a number of industries, in particular hydrolysis production, enables to solve the problem of profitability of organic biomass treatment by its deep complex processing with the resulting components whose cost exceeds the cost of organic raw materials as fuel. Currently, the main results of complex processing of organic raw materials are still energy-intensive products ̶ bioethanol and hydrolyzed lignin, which energy characteristics are commensurate with fossil fuels. Bioethanol production from starch-containing, sugar-containing or lignocellulosic raw materials requires the use of different technological stages and, accordingly, the cost of bioethanol for each type of raw material is different. Compared to bioethanol produced from sugar and starch raw materials, bioethanol manufactured from lignocellulosic raw materials is more expensive. Bioethanol obtained from lignocellulosic raw materials is more expensive compared to bioethanol from sugar and starch raw materials. The most energy-intensive in the technology of bioethanol obtaining from lignocellulosic raw materials is the stage of pretreatment of raw materials for hydrolysis, because the process of preliminary preparation and hydrolysis with dilute acids occurs at high temperatures and pressures. During enzymatic hydrolysis, the process temperature is maintained for a long time (up to several days). To ensure deep integrated processing of plant raw materials, as well as to reduce overall costs, it was proposed to improve the technology and equipment, which allow increasing the degree of conversion of raw materials into basic and by-products.

Phytoaccumulation of heavy metals from municipal solid waste leachate using different grasses under hydroponic condition

Grasses have been used widely to remediate contaminants present in domestic wastewater, but leachate generated from municipal solid waste that usually contain some concentrations of heavy metals has never been reported to be treated with grasses, especially Rhodes grass. A series of experiments was performed to investigate the contaminant uptake from municipal solid waste leachate by Chloris gayana (Rhodes grass) grown in combination with two commonly available grass varieties namely Vetiveria zizanioides (Vetiver grass) and Pennisetum purpureum (Elephant grass). Leachate used for the experiments had high values for chemical oxygen demand (5 g/L), pH (8.5), electrical conductivity (9.0 mS/cm), nitrates (182.1 mg/L), phosphates 6.4 mg/L along with heavy metals i.e. copper, zinc and manganese. Different dilutions of leachate ranging from 0 to 100% were applied in batches and their result showed that collectively all the grasses reduced overall contaminant concentrations. These were reported for chemical oxygen demand, electrical conductivity, nitrates, and phosphates reduced up to 67, 94, 94, and 73%, respectively. Metals uptake by grasses also showed a significant decrease in applied dose i.e. zinc (97%), copper (89%), and manganese (89%). Plant analysis showed that all grasses showed preference to heavy metals uptake e.g. Rhodes grass favoured up taking zinc, Elephant grass for copper and Vetiver grass preferred manganese. Overall growth performance of Rhodes grass was better in dilute leachate, whereas in more concentrated leachate, Rhodes grass did not perform better and production of biomass decreased. In Vetiver grass, root and shoot lengths decreased with increasing leachate strength, but the biomass did not change significantly.

Preface to Special Issue of ChemSusChem on Lignin Valorization: From Theory to Practice

In this Editorial, Guest Editors Run-Cang Sun, Joseph S. M. Samec, and Arthur J. Ragauskas introduce the Special Issue of ChemSusChem on Lignin Valorization: From Theory to Practice. The significance of and enormous challenges for the utilization of lignin are reviewed, and the contents of the Special Issue with highly interesting contributions from scientists around the world are outlined.

Synthesis of Fe3O4 nanoparticles @Trioctylmethylammonium thiosalicylat (TOMATS) as a new magnetic nanoadsorbent for adsorption of ciprofloxacin in aqueous solution

The aim of this research was to investigate ciprofloxacin (CIP) removal efficiency from aqueous solutions by using Fe3O4 nanoparticles @Trioctylmethylammonium thiosalicylat Ionic liquid (Fe3O4 NP@ TOMATS IL) as a new magnetic nanoadsorbent. The adsorbent was characterized by field emission scanning electron microscope-energy dispersive spectroscopy (FESEM-EDS), mapping, Fourier transform infrared spectroscopy (FT-IR), the Brunauer–Emmett–Teller (BET), X-ray powder diffraction (XRD). The effects of solution pH, adsorbent dose, contact time, initial CIP concentration, and temperature on CIP removal were also investigated. In optimal conditions such as pH = 5.6, CIP concentration = 30 mg/L, adsorbent dose = 0.15 g, temperature = 30 °C, contact time = 90 min, the removal efficiency in synthetic and real wastewater were obtained 87 and 73%, respectively. Batch experiments were carried out to study the sorption Kinetics, thermodynamics, and equilibrium isotherms of CIP with magnetic nanoadsorbent. The results show that all of the above factors influence CIP removal. The Langmuir adsorption isotherm fits the adsorption process well, with the pseudo second-order model describing the adsorption kinetics accurately. The thermodynamic parameters indicate that adsorption is mainly physical adsorption. Recycling experiments revealed that the behavior of adsorbent is maintained after recycling for four times.

Lignin-rich sulfated wood nanofibers as high-performing adsorbents for the removal of lead and copper from water

Lignin-rich wood nanofibers (WNFs) were investigated as adsorbents for heavy metals. Lignin-free cellulose nanofibers (CNFs) produced from bleached cellulose fibers were used as a reference. Two raw materials were used to produce WNFs: groundwood pulp as industrially produced wood fibers and sawdust as an abundantly available low-value industrial side stream. WNFs and reference CNFs were produced using a reactive deep eutectic solvent to obtain nanofibers with abundant sulfate groups on their surfaces. With a similar amount of sulfate groups, WNFs had a higher adsorbent performance compared to CNFs and, at low metal concentrations (0.24 mmol/l), the removal of both metals was almost quantitate with WNFs. However, it was noted that, at pHs 4 and 5, the sodium present in the buffer solution interfered with the adsorption, leading to lower adsorption capacities compared to the capacity at pH 3. In addition, in the case of lead, the adsorption capacity dramatically decreased at a high metal concertation, indicating that a high lead concentration results in the saturation of adsorption sites of sulfated nanofibers, leading to a decreased adsorption capacity. Nevertheless, it was observed that WNFs had a higher tolerance to high metal concentrations than CNFs.

Preparation, Physical Characterization and Adsorption Properties of Synthesized Co–Ni–Cr Nanocomposites for Highly Effective Removal of Nitrate: Isotherms, Kinetics and Thermodynamic Studies

In the current effort, the Co–Ni–Cr Nanocomposites were synthesized by chemical method and characterized by means of scanning electron micrographs (SEM), X-ray diffraction (XRD), Fourier trans from infra-red (FTIR), and vibration sample magnetization (VSM). In the final step, these nanoparticles were used to study the nitrate removal efficiency from aqueous solution. The effect of important factor including pH, concentration of Nitrate (NO3 −) ion, contact time and nanoparticle dose were studied in order to find the optimum adsorption conditions. A maximum of removal of the nitrate was observed at pH 4, initial concentration of 40 mg L−1, amount of nanoparticle of 0.06 g L−1 and contact time 60 min. The adsorption isotherm values were obtained and analyzed using the Langmuir, Frenudlich, Temkin and Dubinin–Radushkevich equations, the Temkin isotherm being the one that showed the best correlation coefficient (R2 = 0.999). In addition to, the adsorption kinetics studied by the pseudo-first-order, pseudo-second-order, Elovich model, Ritchie and intraparticle diffusion models. The experimental data fitted to pseudo-second-order (R2 = 0.999).

Adsorption of 2,4-Dichlorophenoxyacetic Acid from Aqueous Solution Using Carbonized Chest Nut as Low Cost Adsorbent: Kinetic and Thermodynamic

The activated carbon was made of carbonized chest nut shell (CCS) and used as low cost adsorbent for 2,4-D (2,4-dichlorophenoxyacetic acid) removal. The experiments were conducted at different temperatures such as 35, 45 and 55 °C and this system represents as L type adsorption behavior. The experimental data were modelled using several isotherm models such as Langmuir, Freundlich, Temkin and Dubinin Radushkevich. The adsorption dynamics were searched by applying pseudo first, pseudo second and intra particle diffusion models. The thermodynamic approach was conducted for determining the thermodynamic values of ΔH°, ΔS° and ΔG°.

Metallurgical Processing Strategies for Metals Recovery from Industrial Slags

Slag produced as a byproduct in industrial processes, contains considerable metals contents, which need to be recovered to avoid environmental contamination. In present review, the types, applications, recovery of metals from slag and their hazardous effects have been discussed. Gravimetric, magnetic, floatation, pyrometallurgical and hydrometallurgical treatments are discussed for processing of charge chrome, steel, copper smelter, brass smelter, tin, incineration, ferrochrome and silico-manganese slags for the extraction of various metal ions (Mg, Cu, Zn, Pb, Cd, Ni, Co, Mn, Fe, As, Cr, Al, Nb, Ag, Au, Nb, Ta, Cu, Co, Ni, Fe, V, Cr). The possibility of biometallurgical processing of slags is also evaluated. Merits and demerits of extraction and purification techniques are highlighted with possible suggestions and possibility of integrated leaching techniques is also discussed.

A Comparative Sorption Study of Ni (II) form Aqueous Solution Using Silica Gel, Amberlite IR-120 and Sawdust

The presence of heavy metals in water causes serious problems and their treatment before incorporating into the water body is a challenge for researchers. The present study was conducted to compare the sorption study of Ni (II) using silica gel, amberlite IR-120 and sawdust of mulberry wood in batch system under the influence of pH, initial Ni (II) concentration and contact time. It was observed that sorption process was depending upon pH and maximum sorption was achieved at pH 7.0. Kinetic data were well fitted into pseudo-second order kinetic model due to high R2 values and closeness of experimental sorption capacity and calculated sorption capacity of pseudo-second order. Isotherms study showed that Langmuir is one of the most suitable choices to explain sorption data due to high R2 values. The monolayer sorption capacities of silica gel, amberlite IR-120 and sawdust were found to be 33.33, 25.19, and 33.67 mg g−1, respectively. Desorption study revealed that NaCl is one of the most appropriate desorbent. It may be concluded from this study that sawdust is a suitable sorbent due to low cost, abundant availability and recycling of the materials for further study.

Fabrication and Evaluation of Cellulose-Alginate-Hydroxyapatite Beads for the Removal of Heavy Metal Ions from Aqueous Solutions

In the present study, the potential of synthesized mixed cellulose, alginate and hydroxyapatite beads for the efficient removal of Ni (II) and Cu (II) ions from aqueous solutions was investigated. Cellulose, alginate and hydroxyapatite are known for their individual adsorption capacity. Beads were prepared in different ratios of these materials. The prepared beads were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), scanning electron microscope (SEM) and thermogravimetric analysis (TGA). FTIR and XRD analysis showed characteristic peaks assigned to cellulose, alginate and hydroxyapatite. Thermal stability was observed to increase with increase of hydroxyapatite percentage in beads. SEM images showed increased surface porosity and roughness with the increase of cellulose percentage. The prepared beads were used for the removal of Ni (II) and Cu (II) ions from aqueous solutions and the process was optimized with respect to pH, contact time, adsorbent dose and initial concentration of metal ions. The values of the coefficient of determination (R2) of the Langmuir and Freundlich adsorption model indicated that the adsorbed Cu (II) and Ni (II) ions form monolayer coverage on the adsorbent surface. In kinetic analysis, Pseudo-second-order model fitted the kinetic experimental data well, as it showed high R2 value; above 0.9990.