Fracture Load and Phase Transformation of Monolithic Zirconia Crowns Submitted to Different Aging Protocols

Experimental bilayer zirconia systems after aging: Mechanical, optical, and microstructural characterization

OBJECTIVES

To characterize two experimental zirconia bilayer materials compared to their monolithic controls, before and after hydrothermal aging.

METHODS

Commercial zirconia powders were utilized to fabricate two bilayer materials: 3Y-TZP+ 5Y-PSZ (3Y+5Y/BI) and 4Y-PSZ+ 5Y-PSZ (4Y+5Y/BI), alongside control groups 3Y-TZP (3Y/C), 4Y-PSZ (4Y/C), and 5Y-PSZ (5Y/C). Compacted specimens were sintered (1550 °C- 2 h, 3 °C/min), and half of them underwent hydrothermal aging (134 °C-20h, 2.2 bar). Characterizations were performed through scanning-electron microscopy (SEM), X-ray diffraction (XRD), Raman spectroscopy, reflectance tests and biaxial flexural strength test (ISO:6872). Weibull statistics were applied to determine the characteristic strength and Weibull modulus. Grain size and optical properties were analyzed using two-way ANOVA followed by the Tukey test.

RESULTS

Degradation regions and monoclinic phase were observed at aged 3Y-TZP and 4Y-PSZ surfaces. Significant differences were observed in the evaluation of optical properties between the bilayer and control groups. The bilayer materials presented intermediate characteristic strength values compared to their controls and aging significantly increased the strength of some groups.

SIGNIFICANCE

Experimental bilayer materials presented lower mechanical properties than monolithic controls, 3Y/C and 4Y/C. Hydrothermal aging increased the characteristic strength of bilayered and monolithic controls, except for 5Y-PSZ. Both experimental bilayer systems, as well as monolithic controls, met the ISO 6872:2015 requirements for single-unit crowns (100 MPa), 3-unit fixed dental prostheses (FDPs) up to premolars (300 MPa), and 3-unit FDPs involving molars (500 MPa). However, for FDPs with four or more units, only monolithic 3Y-TZP and 4Y-PSZ, and bilayered 3Y+5Y met the required minimum flexural strength (≥800 MPa).

Effect of hydrothermal aging on color stability and translucency of two zirconia generations compared to lithium disilicate ceramics

Background

An esthetically acceptable ceramic restoration should have optical properties like the teeth and reflect, transmit, and absorb light. The present investigation compared how hydrothermal aging affected the properties of two types of zirconia and lithium disilicate.

Methods

Thirty rectangular samples (12×14×1 mm) were prepared and sectioned from three different ceramic blocks/blanks (n=10), then assigned into three groups according to the ceramic type: group Z: IPS e.max ZirCAD prime, gradient zirconia (3Y/5Y-TZP); group K: Katana UTML (5Y-TZP); and group E: IPS e.max CAD (lithium disilicate). Color analysis of samples was performed before and after hydrothermal aging (1, 3, and 5 hours) using a spectrophotometer. Color difference (∆E00), translucency parameter (TP00), and contrast ratio (CR) were evaluated. The microstructural analysis was performed using x-ray diffraction (XRD). Data were statistically analyzed at a significance level of P<0.05.

Results

A statistically significant variation was observed across means of ∆E00, TP00, and CR at different times. Group Z displayed the highest statistically significant mean ∆E00. Group E demonstrated the greatest statistically significant mean TP00. Group K exhibited the most statistically significant mean CR.

Conclusion

Hydrothermal aging significantly affected the optical characteristics of lithium disilicate and zirconia ceramics. The translucency of samples increased with aging.

Effect of low-temperature degradation and sintering protocols on the color of monolithic zirconia crowns with different yttria contents

This study investigated the effects of low-temperature degradation (LTD) on the L*, a*, and b* values of highly translucent zirconia crowns. Four types of zirconia disks with different yttria contents (IPS e.max ZirCAD LT, IPS e.max ZirCAD MT, IPS e.max ZirCAD MT Multi, IPS e.max ZirCAD Prime, Ivoclar) and two shades (A2 and BL) were used. A crown was manufactured using four types of zirconia and LTD treated. Color measurements were performed, and the color difference (ΔE00) before and after LTD was calculated. The microstructure was determined through X-ray fluorescence and X-ray diffractometry. Highly translucent zirconia crowns showed greater changes in the a* and b* values than in the L* value after LTD, regardless of the shade. The Multi2 crowns exhibited a discernible color change due to the LTD treatment. The X-ray fluorescence results did not reveal any apparent change in the microstructure between sintering programs for all zirconia specimens.

The effect of phase contents on the properties of yttria stabilized zirconia dental materials fabricated by stereolithography-based additive manufacturing

The aim is to investigate the impact of phase contents on mechanical properties, translucency, and aging stability of additively manufactured yttria partially stabilized zirconia ceramics. For that purpose, we evaluated two PSZ materials. The first type was prepared utilizing commercially available 5 mol% yttria-stabilized zirconia(5Y-PSZ), while the second type, denoted as 3Y+8Y-PSZ ceramics, was fabricated by blending 3 mol% and 8 mol% yttria-stabilized zirconia powders. Compared to 5Y-PSZ (39.90 wt% tetragonal phases and c/a2 = 1.0141), 3Y+8Y-PSZ is characterized by a greater abundance of tetragonal phases (47.68 wt%), which display higher tetragonality (c/a2 = 1.0165) and lower yttrium oxide content (2.25mol%). As a result, the 3Y+8Y-PSZ demonstrates elevated strength (816.52 MPa) and toughness (4.32 MPa m1/2), accompanied by reduced translucency(CR:0.47) and it exhibits greater susceptibility to aging. The phase contents, yttrium oxide content, and lattice parameters in the tetragonal phase play a crucial role in determining the mechanical properties, translucency, and aging stability of PSZ ceramics.

Intraoral low-temperature degradation of monolithic zirconia dental prostheses: 5-year results of a prospective clinical study with ex vivo monitoring

OBJECTIVES

To investigate the 5-year intraoral evolution and kinetics of low-temperature degradation (LTD) of second-generation monolithic prostheses made of 3% molar yttrium-doped tetragonal zirconia polycrystal (3Y-TZP) and the influence of masticatory mechanical stresses and glaze layer on this evolution.

METHODS

A total of 101 posterior tooth elements were included in this prospective clinical study, which comprised ex vivo LTD monitoring (at baseline, 6 months, 1 year, 2 years, 3 years, and 5 years) using Raman spectroscopy (n = 2640 monoclinic phase measurement points per evaluation time) and scanning electron microscopy (SEM). Four types of areas (1-2 mm2 surface, six on molars, and four on premolars) were analysed on each element surface: occlusal, axial, glazed, or unglazed. Raman mapping, high-resolution SEM, and focused ion beam-SEM were performed on selected samples.

RESULTS

The dental prostheses developed a tetragonal-to-monoclinic transformation at the extreme surface of the material after six months in a buccal environment, and this process increased significantly over time. Over the five years of monitoring, the transformation developed nonuniformly with the presence of localised clusters of monoclinic grains. Tribological stresses generate grain pull-out from these clusters, which may raise questions regarding the release of 3Y-TZP nanoparticles into the body. The prosthesis fracture rate was 4.5% after 5 years.

SIGNIFICANCE

LTD developed in vivo on the surfaces of 3Y-TZP dental prostheses and progressed slowly but significantly over time, up to 5 years investigation. However, the effects of aging on the failure rate recorded and of zirconia nanoparticles released into the body require further investigation.

Indirect restorative systems-A narrative review

OBJECTIVE

The background and clinical understanding of the properties of currently available indirect restorative systems and fabrication methods is, along with manufacturer and evidence-based literature, an important starting point to guide the clinical selection of materials for tooth and/or implant supported reconstructions. Therefore, this review explores most indirect restorative systems available in the market, especially all-ceramic, along with aspects of manufacturing process, clinical survival rates, and esthetic outcomes.

OVERVIEW

Progressive incorporation of new technologies in the dental field and advancements in materials science have enabled the development/improvement of indirect restorative systems and treatment concepts in oral rehabilitation, resulting in reliable and predictable workflows and successful esthetic and functional outcomes. Indirect restorative systems have evolved from metal ceramics and polymers to glass ceramics, polycrystalline ceramics, and resin-matrix ceramics, aiming to improve not only biological and mechanical properties, but especially the optical properties and esthetic quality of the reconstructions, in attempt to mimic natural teeth.

CONCLUSIONS

Based on several clinical research, materials, and patient-related parameters, a decision tree for the selection of indirect restorative materials was suggested to guide clinicians in the rehabilitation process.

CLINICAL SIGNIFICANCE

The pace of materials development is faster than that of clinical research aimed to support their use. Since no single material provides an ideal solution to every case, professionals must continuously seek information from well designed, long-term clinical trials in order to incorporate or not new materials and technological advancements.

Ultra-translucent zirconia processing and aging effect on microstructural, optical, and mechanical properties

OBJECTIVES

To evaluate the effect of the ceramic processing and aging method on the microstructure, optical, and mechanical properties of a third generation ultra-translucent zirconia, yttria partially stabilized zirconia (5Y-PSZ).

METHODS

In-house discs were obtained through uniaxial and isostatic pressing an ultra-translucent Y-PSZ powder and sintering at 1450 °C for 2 h. As control, a commercial disc was milled from pre-sintered blocks fabricated with the same 5Y-PSZ powder through isostatic pressing and sintered under the same protocol. Discs were allocated into three groups according to aging condition as immediate (non-aged) and aged using autoclave or hydrothermal reactor at 134ºC for 20 h at 2.2 bar. Crystalline content and microstructure were evaluated using X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. Optical properties were determined using reflectance data to calculate the contrast ratio (CR) and translucency parameter (TP). Mechanical properties were assessed by Vickers hardness, fracture toughness and biaxial flexural strength tests.

RESULTS

XRD spectra revealed a prevalence of cubic (70%) and tetragonal (30%) phases, and the SEM images showed a dense fully crystalline ceramic matrix for both materials. Crystalline content and microstructure of the in-house and commercial 5Y-PSZs were not affected by aging. As-sintered 5Y-PSZs demonstrated similar CR (~0.6) and TP (~18) values, as well as Vickers hardness (~14 GPa) and fracture toughness (~3.8 Mpa.m^1/2), with no significant alteration after both aging methods. In-house and commercial Y-PSZs Weibull moduli ranged from 3.0 to 5.3. 5Y-PSZ processing methods resulted in similar characteristic strength after sintering (592-618 Mpa). While commercial 5Y-PSZ showed no significant influence of aging on strength, hydrothermal reactor aging significantly decreased the in-house Y-PSZ characteristic strength (474 Mpa). Both 5Y-PSZs demonstrated high reliability up to 300-Mpa strength missions, with no detrimental effect of aging (88-100%).

SIGNIFICANCE

Irrespective of the processing method, ultra-translucent 5Y-PSZ showed high aging resistance and translucency stability, as well as strength corresponding to the indication up to short-span anterior prostheses.

Pre-cementation procedures' effect on dental zirconias with different yttria content

OBJECTVE

Several pre-cementation procedures have been advocated to enhance adhesion between zirconia and resin-based cement. There is, however, limited documentation on how these pre-treatments affect the strength of zirconia crowns as most tests are performed on discs or bars. The aim was to assess the effect of pre-cementation procedures on fracture mode, fracture strength and cement retention on zirconia.

METHODS

Two dental zirconia materials with different yttria content were assessed (<4 and>5 mol%). Both discs (n = 45) and crown-shaped specimens (n = 30) of the two materials were pretreated with either air-abrasion or hot-etching with KHF₂ and compared with untreated controls with regards to surface roughness, crystallography, wettability, cement adhesion and fracture strength.

RESULTS AND SIGNIFICANCE

Air-abrasion improves adhesion and strength of zirconia with moderate yttria content (<4 mol%). Acid etching with heated KHF₂ showed the best effect on strength and cement retention on zirconia with higher yttria content (>5 mol%). Application of KHF₂ was, however, complicated on crown-shaped specimens. Pre-treatment and cementation protocols should be optimized for different dental zirconias to improve both strength and retention.

Intraoral low-temperature degradation of monolithic zirconia dental prostheses: Results of a prospective clinical study with ex vivo monitoring

OBJECTIVE

To investigate the intraoral development and kinetics of low-temperature degradation (LTD) in second-generation 3 mol.% yttria-doped tetragonal zirconia polycrystal (3Y-TZP) monolithic prostheses, as well as the influence of masticatory mechanical stress and glaze layer on it.

METHODS

A total of 101 posterior tooth elements were included in a prospective clinical study, which included ex vivo LTD monitoring (at baseline, 6 months, 1 year, and 2 years) using Raman spectroscopy (n = 2640 monoclinic phase measurement points per evaluation time) and SEM. Four types of areas (1-2 mm² surface, 6 on molars, and 4 on premolars) were analyzed on each element surface: occlusal, axial, glazed, or unglazed. Raman depth mapping and high-resolution SEM were performed on the selected samples.

RESULTS

LTD developed in 3Y-TZP monolithic restorations 6 months after intraoral placement and progressed with time. After two years, the tetragonal-to-monoclinic transformation was non-uniform, with the presence of localized clusters of transformed grains. In axial areas, the grain aspect was typical of the classical nucleation-growth process reported for LTD, which progresses from the surface to a depth of several tens of microns. However, in occlusal areas, tribological stress generated surface crushing and grain pull-out from the clusters, which induced an underestimation of the aging process when the evaluation was limited to monoclinic phase quantification. Glazing cannot be considered a protection against LTD.

SIGNIFICANCE

If LTD occurs in dental prostheses in the same way as in orthopedic prostheses, its clinical impact is unknown and needs to be further studied.

Effect of glazing application side and mechanical cycling on the biaxial flexural strength and Weibull characteristics of a Y-TZP ceramic

Glaze application on monolithic zirconia (Y-TZP) can be a practical approach to improve the mechanical properties of this material.

Fracture Load of Different Zirconia Types: A Mastication Simulation Study

PURPOSE

To assess the effect of yttria mol% concentration and material thickness on the biaxial fracture load (N) of zirconia with and without mastication simulation.

MATERIALS AND METHODS

Disk-shaped specimens (N = 120) of 3 mol% yttria-partially stabilized zirconia, 3Y-PSZ (Katana High Translucent, Kuraray Noritake), 4 mol% yttria-partially stabilized zirconia, 4Y-PSZ (Katana Super Translucent Multi Layered) and 5 mol% Yttria-partially stabilized zirconia, 5Y-PSZ (Katana Ultra Translucent Multi Layered) were prepared to thicknesses of 0.7 and 1.2 mm. For each thickness, the biaxial fracture load (N) was measured with and without mastication simulation with 1.2 million cycles at a 110-N load and simultaneous thermal cycling at 5°C to 55°C. The data were analyzed by three-way Analysis of Variance (α = 0.05) and Tukey-Kramer adjusted multiple comparison test.

RESULTS

Yttria mol% concentration and material thickness had a statistically significant effect on the mean biaxial fracture load (F = 388.16, p < 0.001 and F = 714.33, p < 0.001 respectively). The mean biaxial fracture load ranged from the highest to the lowest; 3Y-PSZ, 4Y-PSZ, and 5Y-PSZ (p = 0.012). The mean biaxial fracture load of the 1.2 mm thickness groups was significantly higher than 0.7 mm thickness at any given condition (p = 0.002). Not all specimens survived the mastication simulation protocol. Fifty percent of the 0.7-mm-thick 4Y-PSZ specimens, 70% of the 0.7-mm-thick 5Y-PSZ specimens and 20% of 1.2-mm-thick 5Y-PSZ specimens fractured during mastication simulation. Mastication simulation had no statistically significant effect on the biaxial fracture load (F = 1.24, p = 0.239) of the survived specimens.

CONCLUSIONS

Lowering yttria mol% concentration and increasing material thickness significantly increases the fracture load of zirconia. At 0.7 mm thickness, only 3Y-PSZ survived masticatory simulation. A minimum material thickness of 1.2 mm is required for 4Y-PSZ or 5Y-PSZ.

Hydrothermal degradation methods affect the properties and phase transformation depth of translucent zirconia

OBJECTIVES

To characterize the optical and mechanical properties of a commercial and in-house translucent Y-TZP before and after aging in autoclave or hydrothermal reactor.

METHODS

In-house experimental discs were obtained through uniaxial and isostatic pressing a translucent Y-TZP powder and sintering at 1,550 °C/1 h. Commercial discs were milled from pre-sintered blocks fabricated with the same powder through uniaxial and isostatic pressing and sintering. Discs were allocated into three groups according to aging condition: immediate, aged via autoclave, or reactor (134 °C, 20 h, 2.2 bar). Crystalline content and microstructure were evaluated using X-ray diffraction (XRD) and scanning electron microscopy (SEM). Residual compressive stress (CS) was determined by Raman spectroscopy. Optical properties were determined by the contrast ratio (CR) and translucency parameter (TP) using reflectance data. Mechanical properties were assessed by Vickers hardness, fracture toughness and biaxial flexural strength tests.

RESULTS

XRD and SEM revealed a typical Y-TZP crystalline content, chiefly tetragonal phase, and a dense crystalline matrix for both processing protocols. Reactor aging triggered a more pronounced t-m transformation relative to autoclave. In-house and commercial Y-TZPs demonstrated similar CR and TP, with reactor aging significantly increasing their translucency. Similarly, reactor aging influenced Vickers hardness and fracture toughness. In-house processed Y-TZP clearly demonstrated the presence of CS, whereas commercial Y-TZP showed no presence of CS. Non-aged in-house Y-TZP resulted in significantly lower characteristic strength relative to commercial Y-TZP. While aging protocols significantly increased the characteristic strength of in-house Y-TZP, reactor significantly decreased commercial Y-TZP characteristic strength. Both Y-TZP processing protocols demonstrated high reliability at high-stress missions, with no detrimental effect of aging.

CONCLUSIONS

Laboratory aging methodology significantly influenced optical and mechanical properties of a commercial and in-house translucent Y-TZP.

Effect of finishing/polishing techniques and low temperature degradation on the surface topography, phase transformation and flexural strength of ultra-translucent ZrO2 ceramic

OBJECTIVE

To investigate the effect of different surface finishing and polishing regimes and low temperature degradation on flexural strength, phase transformation and surface topography of ultra-translucent ZrO₂ ceramic.

METHODS

300 (n=15/group) of conventional zirconia (Z: Ice Zirkon Transluzent) and ultra-translucent zirconia (UT: Prettau Anterior) bar-specimens were made and divided according to the "Finishing/Polishing" - (C - Control, B - diamond rubber polishers, P - adjusting with burs, PB - adjusting with burs+diamond polishers, PG - adjusting with burs+glaze), "Low temperature Degradation (LTD)" (with or without a treatment at 127°C, 1.7bar/24h). Then, a 3-point mini flexural test was performed in a universal testing machine (1mm/min, 500kgf load cell). SEM, EDS, XDR, AFM, optical profilometry and Weibull analysis were performed. Data were analyzed by 3-way ANOVA and Tukey's post-test (5%).

RESULTS

Groups ZPB_D (1670±253MPa), ZB_D (1664±217MPa), and ZB (1655±3678MPa) showed significantly higher flexural strength than the UTPG group (372±56MPa). The Weibull modulus was significantly higher for the ZP_D group compared to the UB, UC_D, UP_D and UPB_D, while UTB, UTC_D and UTP_D had the lowest value. Monoclinic phases were observed only in the conventional zirconia groups and were more evident after LTD. Diamond rubber polishers presented less roughness for both zirconias.

SIGNIFICANCE

The use of diamond rubber polishers is the most suitable finishing/polishing method for zirconia ceramic restorations and that final glazing reduces the fracture resistance of these materials.

Does the application of surface treatments in different sintering stages affect flexural strength and optical properties of zirconia?

OBJECTIVE

To investigate the influence of surface treatments conducted in presintering and postsintering stages on flexural strength and optical properties of zirconia.

MATERIALS AND METHODS

Specimens were milled from partially sintered zirconia blocks in different geometries and divided into three main groups as presintered, postsintered, and control groups. Test groups were further divided into three subgroups (n = 10) according to the surface treatments conducted (grinding, Er,Cr:YSGG laser irradiation, air-borne particle abrasion [APA]). Four-point flexural strength (σ) test and Weibull analysis were conducted. Color differences (ΔE₀₀ ) and translucency parameter (TP_ab ) were calculated with a spectrophotometer. Surfaces of specimens were scrutinized under FESEM. Data were statistically analyzed.

RESULTS

Postsintered groups exhibited higher σ values (P < .05). Within all groups, highest and lowest σ values were detected at postsintered and presintered APA groups, respectively (P < .05). All ΔE₀₀ values were above the perceptibility threshold (ΔE₀₀  > 0.8). Higher TP_ab values were obtained and deeper scratches were observed in presintered groups.

CONCLUSIONS

Surface treatments performed at postsintering stage had a favorable effect on the flexural strength of all specimens. Surface treatments performed before sintering increased translucency and caused higher ΔE₀₀ values.

CLINICAL SIGNIFICANCE

Surface treatments performed at different sintering stages can alter mechanical and optical properties of zirconia.

Effects of accelerated artificial aging on the translucency and color stability of monolithic ceramics with different surface treatments

STATEMENT OF PROBLEM

Different surface finishing procedures can be applied to monolithic restorations. However, information is limited regarding the long-term performance of these procedures.

PURPOSE

The purpose of this in vitro study was to evaluate the effect of aging on the translucency and color stability of monolithic ceramics with different surface finishing procedures.

MATERIAL AND METHODS

Disk-shaped (14×1.5 mm) specimens of monolithic zirconia (Zirkonzahn Prettau [ZZ]) and lithium disilicate glass-ceramic (IPS e.max Press [IPS]) were fabricated. The specimens were divided into 3 subgroups according to the surface treatments (n=9, G: glazing, R: rubber polishing system, and P: rubber polishing system followed by polishing paste). Color measurements were made by using a spectrophotometer before and after an ultraviolet aging process. L*, a*, and b* parameters were recorded. ΔE and translucency parameter (TP) values were calculated. One specimen from each subgroup was examined by scanning electron microscopy (×30 000). The data were statistically analyzed using the Mann-Whitney U, Kruskal-Wallis, and post hoc tests (α=.05).

RESULTS

ΔE values of group ZZ (5.03) exceeded the clinically acceptable level (3.5); however, the color change was not clinically perceptible for IPS (0.41). The ΔE value of the subgroup P was found to be higher than that of the others for ZZ (P<.001). The ΔE value was not affected by the surface treatment for IPS. Group IPS showed significantly higher translucency than the ZZ group (P<.001). TP values were not affected by the surface treatment in either material and decreased after aging. However, changes in the TP values were too slight to be clinically perceptible.

CONCLUSIONS

Lithium disilicate ceramic was found to be more esthetic than monolithic zirconia ceramic in terms of color stability and translucency.

Strength and aging resistance of monolithic zirconia: an update to current knowledge

New zirconia compositions with optimized esthetic properties have emerged due to the fast-growing technology in zirconia manufacturing. However, the large variety of commercial products and synthesis routes, make impossible to include all of them under the general term of “monolithic zirconia ceramics”. Ultra- or high translucent monolithic formulations contain 3–8 mol% yttria, which results in materials with completely different structure, optical and mechanical properties. The purpose of this study was to provide an update to the current knowledge concerning monolithic zirconia and to review factors related to strength and aging resistance. Factors such as composition, coloring procedures, sintering method and temperature, may affect both strength and aging resistance to a more or less extend. A significant reduction of mechanical properties has been correlated to high translucent zirconia formualtions while regarding aging resistance, the findings are contradictory, necessitating more and thorough investigation. Despite the obvious advantages of contemporary monolithic zirconia ceramics, further scientific evidence is required that will eventually lead to the appropriate laboratory and clinical guidelines for their use. Until then, a safe suggestion should be to utilize high-strength partially-stabilized zirconia for posterior or long span restorations and fully-stabilized ultra-translucent zirconia for anterior single crowns and short span fixed partial dentures.

Influence of substrate design for in vitro mechanical testing

Background

The goal of this study was to evaluate the influence of dental substrate simulator material, and the presence of root and periodontal ligament on the stress distribution in an adhesively-cemented monolithic crown.

Material and Methods

Five (5) 3D models according to the substrate simulator material and shape were modeled with CAD software for conducting non-linear finite element analysis (FEA): Tooth with and without periodontal ligament - subgroup "pl" (groups Tooth+pl and Tooth-pl), machined tooth in epoxy-resin with and without pulp chamber - subgroup "pc" (ER+pc and ER-pc) and simplified epoxy-resin substrate without pulp chamber and roots (SiER). Next, adhesively-cemented monolithic crowns in zirconia reinforced lithium silicate were modeled over each substrate. The solids were then imported in STEP format to the analysis software and the contact between teeth and cylinder was considered perfectly bonded; whereas, the contacts involving the resin cement were considered as non-separated. The materials were considered isotropic, linearly elastic, and homogeneous. An axial load (600 N) was applied to the occlusal surface and results of maximum principal stress (MPa) on the restoration were required.

Results

FEA revealed that all evaluated subtracts showed the crown intaglio surface as the most stressed region. The average stress and stress peaks were similar for restorations cemented onto Tooth+pl, Tooth-pl and ER+pc substrates, but, 13% higher in comparison to ER-pc and SiER substrates.

Conclusions

Simplified substrates can be used to evaluate posterior full crown behavior without periodontal ligaments and roots, since the rigidity of the specimen is taken into account. Key words:Finite element analysis, axial loading, computed assisted numerical analisys, monolithic crowns,methodological study.

Translucency of Zirconia Ceramics before and after Artificial Aging

PURPOSE

The aging of zirconia ceramics (Y-TZP) is associated with tetragonal to monoclinic phase transformation. This change in microstructure may affect the optical properties of the ceramic. This study examines the effect of aging on the translucency of different zirconia materials.

MATERIALS AND METHODS

120 disc-shaped specimens were fabricated from four zirconia materials: Cercon ht white, BruxZir Solid Zirconia, Zenostar T0, Lava Plus (n = 30 per group). Accelerated aging was performed in a steam autoclave (134°C, 0.2 MPa, 5 hours). CIELab coordinates (L*, a*, b*) and luminous reflectance (Y) were measured with a spectrophotometer before and after aging. Contrast ratio (CR) and translucency parameter (TP) were calculated from the L*, a*, b*, and Y tristimulus values. The general linear model (Bonferroni adjusted) was used to compare both parameters before and after aging, as well as between the different zirconia materials (p ≤ 0.05).

RESULTS

CR and TP differed significantly before and after aging in all groups tested. Before aging, Zenostar T showed the highest and Lava Plus showed the lowest translucency. After aging, Cercon ht and Zenostar T showed the highest and BruxZir and Lava Plus the lowest translucency.

CONCLUSIONS

Aging reduced the translucency in all specimens tested. Furthermore, translucency differed between the zirconia brands tested. Nevertheless, the differences were below the detectability threshold of the human eye. The aging process can influence the translucency and thus the esthetic outcome of zirconia restorations; however, the changes in translucency were minimal and probably undetectable by the human eye.

Mechanical behavior of yttria-stabilized tetragonal zirconia polycrystal: Effects of different aging regimens

This study aimed to characterize and compare the effect of different aging regimens on surface characteristic (topography and roughness), structural stability (phase transformation) and mechanical performance (Weibull analysis) of a Y-TZP ceramic. Discs (15 × 1.2 mm; VITA In-Ceram YZ) were prepared according to ISO 6872-2015 for biaxial flexural strength testing and randomly assigned into five groups (n = 30): as-sintered, no aging treatment (CTRL); 20 h in autoclave at 134°C, 2 bar pressure (AUT); intermittent mechanical loading at 20 Hz/106 load pulses (MechLoad); AUT followed by MechLoad (AUT+MechLoad); and storage in distilled water at 37°C, for 1 year (STO). The following analyses were performed: roughness (n = 30), surface topography (n = 2), phase transformation (n = 2) and biaxial flexure strength (n = 30). Phase transformation (increase of m-phase content) was shown to be a spontaneous, unavoidable and time-dependent process, occurring even under ambient conditions (dry storage after 1 year = 6.0% increase), and is considerably accelerated in the presence of moisture (STO = 17.6%; AUT= 63.1%; and AUT+MechLoad = 59.9%). For roughness parameters, only Ra was affected by aging, and the highest values were observed for AUT+MechLoad (0.25 ± 0.07 µm). For Weibull analysis, structural reliability (Weibull moduli) and characteristic strength were not impaired after aging, and some aging conditions led to increased values (highest weibull moduli in AUT, and highest characteristic strength in STO). Phase transformation proves to be a time-dependent spontaneous mechanism that is accelerated in the presence of different stimuli. However, none of the aging regimens had a negative effect on the characteristic strength and structural reliability of Y-TZP ceramic.

In vitro analysis of the fracture resistance of CAD-CAM monolithic zirconia molar crowns with different occlusal thickness

OBJECTIVES

To compare the fracture resistance and mode of failure of CAD-CAM monolithic zirconia crowns with different occlusal thickness.

MATERIAL AND METHODS

Forty CAD-CAM monolithic zirconia crowns with different occlusal thickness were randomly distributed into 4 experimental groups: 2.0mm (group 1), 1.5mm (group 2), 1.0mm (group 3) and 0.5mm (group 4). The restorations were cemented onto human molars with a self-adhesive resin cement. The specimens were loaded until fracture; the fracture resistance and mode of failure were recorded. The data were statistically analyzed with the one-way ANOVA followed by the Fisher׳s Exact test with Bonferroni׳s correction (p=0.05).

RESULTS

The fracture resistance values of all the specimens exceeded the maximum physiological occlusal loads in molar regions. All the crowns showed cohesive microcracks of the zirconia core; only 1 crown with a thickness of 0.5mm was interested by a complete fracture.

CONCLUSIONS

The occlusal thickness of CAD-CAM monolithic zirconia crowns did not influence either the fracture resistance and the mode of failure of the restorations; the occlusal thickness of CAD-CAM monolithic zirconia crowns can be reduced up to a lower bound of 0.5mm keeping a sufficient strength to withstand occlusal loads; CAD-CAM monolithic zirconia crowns showed sufficient fracture resistance to be used in molar regions, even in a thin configuration (0.5mm).