Critical Role of Etching Parameters in the Evolution of Nano Micro SLA Surface on the Ti6Al4V Alloy Dental Implants

The effect of porous compliance bushings in a dental implant on the distribution of occlusal loads

Porous dental implants are clinically used, but the mechanism of load distribution for stepped implant shaft surrounded by compliance bushings is still not known, especially for different bone conditions. The aim of the study was to assess the impact of the design of a dental implant with compliance bushings (CBs) on the occlusal load distribution during primary and secondary stability using finite element simulation (FEA), with a distinction between low and high quality cervical support under primary stability. The FEA of the oblique occlusal load transfer (250 N; 45°) was carried out for implants under variable bone conditions. The stepped shaft in the intermediate part of the dental implant was surrounded by CBs with an increasing modulus of elasticity of 2, 10 and 50 GPa. With a smaller Young's modulus of the bushings the increase of stress in the trabecular bone indicated that more bone tissue can be protected against disuse. The beneficial effect for the trabecular bone derived from the reduction of the stiffness of the bushings in relation to the loss of the implant's load bearing ability can be assessed using the FEM method.

Enhanced osseointegration of drug eluting nanotubular dental implants: An in vitro and in vivo study

Faster and predictable osseointegration is crucial for the success of dental implants, especially in patients with compromised local or systemic conditions. Despite various surface modifications on the commercially available Titanium (Ti) dental implants, the bioactivity of Ti is still low. Thus, to achieve both biological and therapeutic activity on titanium surfaces, surface modification techniques such as titanium nanotubes have been studied as nanotube surfaces can hold therapeutic drugs and molecules. The main aim of the present research work is to study the early osseointegration around the novel Simvastatin drug eluting nanotubular dental implant. In the present research, the titanium nanotubes were fabricated on the screw-shaped dental implant surface and the Simvastatin drug was loaded into the nanotubes using the ultrasonication dip method. In vitro and In vivo studies were carried out on the modified dental implants. In vitro cell culture study reported enhanced osteogenic activity on the drug-loaded nanotube surface implants. The invivo animal studies were evaluated by micro-CT, histopathology, and reverse torque removal analysis methods. The test results showed faster osseointegration with the strong interface on the Simvastatin drug-loaded implant surface at 4 weeks of healing as compared to the control implants.

Surface Coatings of Dental Implants: A Review

Replacement of missing teeth is possible using biocompatible devices such as endosseous implants. This study aims to analyze and recognize the best characteristics of different implant surfaces that ensure good peri-implant tissue healing and thus clinical success over time. The present review was performed on the recent literature concerning endosseous implants made of titanium, a material most frequently used because of its mechanical, physical, and chemical characteristics. Thanks to its low bioactivity, titanium exhibits slow osseointegration. Implant surfaces are treated so that cells do not reject the surface as a foreign material and accept it as fully biocompatible. Analysis of different types of implant surface coatings was performed in order to identify ideal surfaces that improve osseointegration, epithelial attachment to the implant site, and overall peri-implant health. This study shows that the implant surface, with different adhesion, proliferation, and spreading capabilities of osteoblastic and epithelial cells, influences the cells involved in anchorage. Implant surfaces must have antibacterial capabilities to prevent peri-implant disease. Research still needs to improve implant material to minimize clinical failure.

Surface Modifications of Commercial Dental Implant Systems: An Overview

The aim of this review was to perform a comprehensive overview of evidence pertaining to the influence of various surface modifications on the surface roughness, bone implant contact, and the success and complication rates of the implants. Modified sandblasted, large-grit, acid-etched (SLA) implants (SLActive implants) have a higher implant stability quotient compared with conventional SLA implants. Also, when compared between the implant surfaces from various manufacturers, Biomet 3i Nanotite implants were shown to have a relatively higher implant stability quotient compared to Straumann implants as well as the Biomet Osseotite implants. Only one study reports the insertion torque values as obtained by the various implant surfaces, with the findings being statistically similar for all the types, and a higher mean value for Biomet 3i Nanotite implants. Among SLA and SLActive surfaces, the latter was found to have a lower marginal bone loss, and among Astratech implants, the marginal bone loss levels were similar for Osseospeed and Tioblast surfaces. When Osseospeed, TiUnite and SLActive surfaces were compared, Osseospeed was found to have the minimum bone loss while TiUnite was found to have the highest. The bone implant contact percentages are similar and satisfactory for most of the implant surface modifications that are available currently. Upon assessing the recent literature on the survival rates for implants with various surface modifications, it was found that among Nobel Biocare implants, the survival rate was higher for TiUnite implants, compared with the turned surfaces. Surprisingly, among the Straumann implant surfaces, the survival rates were found to be higher for the SLA implants when compared to the modified SLA implants. Only one of the included studies evaluated the survival rate for Astratech implant surfaces and found a 100% survival rate for both the Osseospeed and Tioblast surface implants. Therefore, major advancements have been made in developing novel surfaces of dental implants. The numerous innovations set the stage for rehabilitating patients with high success and predictable survival rates even in challenging conditions.

Latest Trends in Surface Modification for Dental Implantology: Innovative Developments and Analytical Applications

An increase in the world population and its life expectancy, as well as the ongoing concern about our physical appearance, have elevated the relevance of dental implantology in recent decades. Engineering strategies to improve the survival rate of dental implants have been widely investigated, focusing on implant material composition, geometry (usually guided to reduce stiffness), and interface surrounding tissues. Although efforts to develop different implant surface modifications are being applied in commercial dental prostheses today, the inclusion of surface coatings has gained special interest, as they can be tailored to efficiently enhance osseointegration, as well as to reduce bacterial-related infection, minimizing peri-implantitis appearance and its associated risks. The use of biomaterials to replace teeth has highlighted the need for the development of reliable analytical methods to assess the therapeutic benefits of implants. This literature review considers the state-of-the-art strategies for surface modification or coating and analytical methodologies for increasing the survival rate for teeth restoration.