Fabrication and Water Treatment Application of Carbon Nanotubes (CNTs)-Based Composite Membranes: A Review

Synergistic Interaction of Ionic Liquid Grafted Poly(vinylidene Fluoride) and Carbon Nanotubes to Construct Water Treatment Membranes with Multiple Separation Properties

In this study, the dual strategy of 1-butyl-3-vinylimidazolium bromide ionic liquid (IL) grafting and carbon nanotubes (CNTs) nanocomposition was applied to modify poly(vinylidene fluoride) (PVDF)-based membranes. The highly hydrophilic/oleophobic and fouling-resistant PVDF-g-IL/CNTs membranes with excellent separation efficiency were obtained by the nonsolvent-induced phase separation method with ethanol-water mixed solution as the coagulation bath. The grafted IL not only generated hydrophilic groups on PVDF chains but also acted together with the CNTs to induce the formation of hydrophilic β-crystalline phase of PVDF, which significantly improved the hydrophilicity and pore structure of the modified PVDF membranes. As a result, the pure water flux of the optimal membrane increased up to 294.2 L m-2 h-1, which was 5.2 times greater than that of the pure PVDF membrane. Simultaneously, the electrostatic interaction of the positive IL and the integration of CNTs enhanced adsorption sites of the membranes, producing exceptional retention and adsorption of dye wastewater and oil-water emulsion. This study presents a straightforward and efficient approach for fabricating PVDF separation membranes, which have potential applications in the purification of various polluted wastewater.

Sensitive Cr3+ sensor based on novel poly(luminol-co-1,8-diaminonaphthalene)/CeO2/MWCNTs nanocomposites

In this study, poly(luminol-co-1,8-diaminonaphthalene) (PLim-DAN) was synthesized and subsequently modified with MWCNTs and CeO2 NPs. The synthesized nanocomposites were analyzed using IR, SEM, TEM, and XRD. Furthermore, a comprehensive set of thermal behavior measurements were taken using TGA/DTG analysis. Next, the electroactivity of the developed nanocomposites was tested as an electrochemical sensor to measure the concentration of Cr3+ ions in phosphate buffers. The GCE adapted with the PLim-DAN/CeO2/CNTs-10% nanocomposite (NC) exhibited the highest current response among the other compositions and copolymers. The fabricated nanocomposite sensor showed high sensitivity, with a value of 19.78 μA μM-1 cm-2, and a low detection limit of 4.80 ± 0.24 pM. The analytical performance was evaluated by plotting a current calibration curve versus the concentration of Cr3+ ions. It was found to be linear (R2 = 0.9908) over the range of 0.1 nM to 0.1 mM, identified as the linear dynamic range (LDR). This electrochemical sensor demonstrated that it could be a useful tool for environmental monitoring by accurately detecting and measuring carcinogenic Cr3+ ions in real-world samples.

Curvature effects regulate the catalytic activity of Co@N4-doped carbon nanotubes as bifunctional ORR/OER catalysts

The advancement of metal-air batteries relies significantly on the development of highly efficient bifunctional catalysts for the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER). Herein, we investigate the potential application of Co@N4-doped carbon nanotubes (Co@N4CNTs) as bifunctional catalysts using density functional theory calculations. We explore the stability and electronic properties of Co@N4CNTs by analyzing energies, bond lengths, conducting ab initio molecular dynamics simulations, and examining the density of states. Notably, the diameter of the nanotubes has a notable impact on the catalytic performance of Co@N4CNTs. A remarkable 54% improvement in catalytic activity when transitioning from (4, 4) to (24, 4) Co@N4CNTs, with ηBi from changing from 1.40 to 0.64 V. We have several exceptional catalysts with low overpotentials, including (18, 4), (22, 4), and (24, 4) Co@N4CNTs, which exhibit ηBi values of 0.68, 0.67, and 0.64 V, respectively. Moreover, we link the increased activity of Co@N4CNTs to the change of Co atom's partial d orbital energy, facilitated by adjustments in the diameter of Co@N4CNTs. This revelation offers valuable insights into the underlying factors driving the enhancement of catalytic activity through alterations in orbital energy levels. Our research uncovers several excellent catalysts and provides valuable insights for the design and development of efficient catalysts for metal-air batteries.

Design and function of lignin/silk fibroin-based multilayer water purification membranes for dye adsorption

The treatment of dye wastewater poses a significant challenge to the sewage recycling industries. However, the reduction of secondary pollution resulting from the membrane residues, to maintain high performance, remains a considerable obstacle. A novel approach for the fabrication of multilayer nanofiber structures using a layer-by-layer electrostatic spinning technique with biological materials was reported in this study. Incorporating the chemical adsorption advantages of lignin nanofiber and the physical adsorption advantages of silk fibroin (SF) nanofiber enabled the full realization of excellent dye interception performance. A comparative analysis was conducted on the lignin derived from eucalyptus, pine, and straw to determine the most suitable option. Notably, eucalyptus lignin exhibited superior antimicrobial properties. The adsorption of crystal violet by eucalyptus lignin/SF membrane was consistent with the Freundlich isotherm model and the pseudo-second-order kinetic model, revealing a chemisorption mechanism involving Π-Π conjugation, hydrogen bonding, and the binding of anions and cations. The lignin/SF membrane exhibited a retention rate exceeding 99.5 % for crystal violet, methylene blue, and brilliant green dyes. Furthermore, it demonstrated efficacy in retaining heavy metal ions, including cadmium and copper. The original biomass material imparts the property of rapid degradation to a multilayer membrane that can be used as an effective and eco-friendly water purification material.

A Review on CNTs-Based Electrochemical Sensors and Biosensors: Unique Properties and Potential Applications

Carbon nanotubes (CNTs), are safe, biocompatible, bioactive, and biodegradable materials, and have sparked a lot of attention due to their unique characteristics in a variety of applications, including medical and dye industries, paper manufacturing and water purification. CNTs also have a strong film-forming potential, permitting them to be widely employed in constructing sensors and biosensors. This review concentrates on the application of CNT-based nanocomposites in the production of electrochemical sensors and biosensors. It emphasizes the synthesis and optimization of CNT-based sensors for a range of applications and outlines the benefits of using CNTs for biomolecule immobilization. In addition, the use of molecularly imprinted polymer (MIP)-CNTs in the production of electrochemical sensors is also discussed. The challenges faced by the current CNTs-based sensors, along with some the future perspectives and their future opportunities, are also briefly explained in this paper.

Fabrication and Evaluation of Multiwalled Carbon Nanotube-Containing Bijels and Bijels-Derived Porous Nanocomposites

Structures having continuous porous networks are of great interest for applications in areas such as separation, energy storage, and tissue engineering. Bicontinuous interfacially jammed emulsion gels ("bijels") have been actively investigated as templates for fabricating useful structures for such applications. However, the fabrication of bijels-templated porous nanocomposites incorporated with reinforcing or functional nanoparticles (or nanofibers) to provide specific, targeted functions is still a challenge, stemming from the difficulties of fabricating functional nanoparticle-containing bijels. In this study, bijels-derived porous nanocomposites incorporated with multiwalled carbon nanotubes (MWCNTs), which possessed interconnected channels inside the structures, were made via a facile phase inversion technique for bijels fabrication. For the composite manufacture, in the first step of bijels fabrication, MWCNT adsorption into the oil phase of bijels was observed. It was revealed that MWCNTs were physically absorbed into the oil-rich phase without disrupting the bicontinuous structure of bijels. The successful fabrication of non-crosslinked and crosslinked porous structures containing MWCNTs was evidenced through imaging by confocal laser scanning microscopy and scanning electron microscopy, respectively. For potential controlled release applications, an anticancer drug, doxorubicin hydrochloride (DOX), was incorporated into bijels-derived structures and nanocomposites. The in vitro DOX release profiles from drug delivery systems based on bijels-derived MWCNT-containing nanocomposites suggested that the photothermal effect of MWCNTs initiated by near-infrared irradiation could modulate the drug release behavior. Overall, this study has developed a facile approach to fabricate bijels-templated bicontinuous porous structures incorporated with functional nanoparticles (or nanofibers) and opened an avenue for making MWCNT-containing porous nanocomposites for controlled drug release applications.

Synthesis and applications of graphitic carbon nitride (g-C3N4) based membranes for wastewater treatment: A critical review

Semiconducting membrane combined with nanomaterials is an auspicious combination that may successfully eliminate diverse waste products from water while consuming little energy and reducing pollution. Creating an inexpensive, steady, flexible, and diversified business material for membrane production is a critical challenge in membrane technology development. Because of its unusual structure and high catalytic activity, graphitic carbon nitride (g-C3N4) has come out as a viable material for membranes. Furthermore, their great durability, high permanency under challenging environments, and long-term use without decrease in flux are significant advantages. The advanced material techniques used to manage the molecular assembly of g-C3N4 for separation membrane were detailed in this review work. The progress in using g-C3N4-based membranes for water treatment has been detailed in this presentation. The review delivers an updated description of g-C3N4 based membranes and their separation functions and new ideas for future enhancements/adjustments to address their weaknesses in real-world situations. Finally, the ongoing problems and promising future research directions for g-C3N4-based membranes are discussed.

An Insight into Carbon Nanomaterial-Based Photocatalytic Water Splitting for Green Hydrogen Production

At present, the energy shortage and environmental pollution are the burning global issues. For centuries, fossil fuels have been used to meet worldwide energy demand. However, thousands of tons of greenhouse gases are released into the atmosphere when fossil fuels are burned, contributing to global warming. Therefore, green energy must replace fossil fuels, and hydrogen is a prime choice. Photocatalytic water splitting (PWS) under solar irradiation could address energy and environmental problems. In the past decade, solar photocatalysts have been used to manufacture sustainable fuels. Scientists are working to synthesize a reliable, affordable, and light-efficient photocatalyst. Developing efficient photocatalysts for water redox reactions in suspension is a key to solar energy conversion. Semiconductor nanoparticles can be used as photocatalysts to accelerate redox reactions to generate chemical fuel or electricity. Carbon materials are substantial photocatalysts for total WS under solar irradiation due to their high activity, high stability, low cost, easy production, and structural diversity. Carbon-based materials such as graphene, graphene oxide, graphitic carbon nitride, fullerenes, carbon nanotubes, and carbon quantum dots can be used as semiconductors, photosensitizers, cocatalysts, and support materials. This review comprehensively explains how carbon-based composite materials function as photocatalytic semiconductors for hydrogen production, the water-splitting mechanism, and the chemistry of redox reactions. Also, how heteroatom doping, defects and surface functionalities, etc., can influence the efficiency of carbon photocatalysts in H2 production. The challenges faced in the PWS process and future prospects are briefly discussed.

Recent Advances in the Use of CoPc-MWCNTs Nanocomposites as Electrochemical Sensing Materials

Cobalt phthalocyanine multiwalled carbon nanotubes (CoPc-MWCNTs), a nanocomposite, are extraordinary electrochemical sensing materials. This material has attracted growing interest owing to its unique physicochemical properties. Notably, the metal at the center of the metal phthalocyanine structure offers an enhanced redox-active behavior used to design solid electrodes for determining varieties of analytes. This review extensively discusses current developments in CoPc-MWCNTs nanocomposites as potential materials for electrochemical sensors, along with their different fabrication methods, modifying electrodes, and the detected analytes. The advantages of CoPc-MWCNTs nanocomposite as sensing material and its future perspectives are carefully reviewed and discussed.

Recent Advances in the Lithium Recovery from Water Resources: From Passive to Electrochemical Methods

The ever-increasing amount of batteries used in today's society has led to an increase in the demand of lithium in the last few decades. While mining resources of this element have been steadily exploited and are rapidly depleting, water resources constitute an interesting reservoir just out of reach of current technologies. Several techniques are being explored and novel materials engineered. While evaporation is very time-consuming and has large footprints, ion sieves and supramolecular systems can be suitably tailored and even integrated into membrane and electrochemical techniques. This review gives a comprehensive overview of the available solutions to recover lithium from water resources both by passive and electrically enhanced techniques. Accordingly, this work aims to provide in a single document a rational comparison of outstanding strategies to remove lithium from aqueous sources. To this end, practical figures of merit of both main groups of techniques are provided. An absence of a common experimental protocol and the resulting variability of data and experimental methods are identified. The need for a shared methodology and a common agreement to report performance metrics are underlined.

Incorporating Carbon Nanotubes in Nanocomposite Mixed-Matrix Membranes for Gas Separation: A Review

Carbon nanotube (CNT) is a prominent material for gas separation due to its inherent smoothness of walls, allowing rapid transport of gases compared to other inorganic fillers. It also possesses high mechanical strength, enabling membranes to operate at high pressure. Although it has superior properties compared to other inorganic fillers, preparation of CNTs into a polymer matrix remains challenging due to the strong van der Waals forces of CNTs, which lead to agglomeration of CNTs. To utilize the full potential of CNTs, proper dispersion of CNTs must be addressed. In this paper, methods to improve the dispersion of CNTs using functionalization methods were discussed. Fabrication techniques for CNT mixed-matrix membrane (MMM) nanocomposites and their impact on gas separation performance were compared. This paper also reviewed the applications and potential of CNT MMMs in gas separation.

Applications of Polymeric Membranes with Carbon Nanotubes: A Review

Nanomaterials have been commonly employed to enhance the performance of polymeric membrane materials that are used in several industrial applications. Carbon nanotubes (CNTs) have gained notable attention over the years for use in membrane technology due to their anti-biofouling properties, salt rejection capability, exceptional electrical conductivity, and mechanical properties. This paper aims to discuss some of the recent applications of CNTs in membrane technology and their effect on a larger scale. The paper reviews successful case studies of incorporation of CNTs in membranes and their impact on water purification, desalination, gas separations, and energy storage, in an effort to provide a better understanding of their capabilities. Regarding the future trends of this technology, this review emphasizes improving the large-scale production processes and addressing environmental and health-related hazards of CNTs during production and usage.

Unfunctionalized and Functionalized Multiwalled Carbon Nanotubes/Polyamide Nanocomposites as Selective-Layer Polysulfone Membranes

Nowadays, reverse osmosis is the most widely utilized strategy in membrane technology due to its continuous improvement. Recent studies have highlighted the importance of the surface characteristics of support layers in thin-film membranes to improve their reverse osmosis performance. In this study, interfacial polymerization was used to generate the membranes by employing polyamide as a selective layer on top of the polysulfone supporting sheet. Different membranes, varying in terms of the concentrations of unfunctionalized and functionalized multiwalled carbon nanotubes (MWCNTs), as well as ethanol, have been fabricated. The efficiency of the membrane has been increased by increasing its permeability towards water with high salt rejection. Different characterization techniques were applied to examine all of the fabricated membranes. PA-EtOH 30% (v/v), as a selective layer on polysulfone sheets to enhance the membrane’s salt rejection, was shown to be the most efficient of the suggested membranes, improving the membrane’s salt rejection. The water permeability of the polyamide membrane with EtOH 30% (v/v) was 56.18 L/m² h bar, which was more than twice the average permeability of the polyamide membrane (23.63 L/m² h bar). The salt rejection was also improved (from 97.73% for NaCl to 99.29% and from 97.39% for MgSO₄ to 99.62% in the same condition). The PA-MWCNTs 0.15% membrane, on the other hand, had a reduced surface roughness, higher hydrophobicity, and higher water contact angle readings, according to SEM. These characteristics led to the lowest salt rejection, resulting from the hydrophobic nature of MWCNTs.

Advances in endocrine toxicity of nanomaterials and mechanism in hormone secretion disorders

The size of nanoparticles is about 1-100 nm. People are exposed to nanoparticles in environmental pollutants from ancient times to the present. With the maturity of nanotechnology in the past two decades, the production of manufactured nanomaterials is rapidly increasing and they are used in a wide range of aerospace, medicine, food, and industrial applications. However, both natural and manufactured nanomaterials have been proved to pose a threat to diverse organs and systems. The endocrine system is critical to maintaining homeostasis. Endocrine disorders are associated with many diseases, including cancer, reduced fertility, and metabolic diseases. Therefore, we review the literatures dealing with the endocrine toxicity of nanomaterial. This review provides an exhaustive description of toxic effects of several common nanomaterials in the endocrine system; more involved are reproductive endocrinology. Then physicochemical factors that determine the endocrine toxicity of nanomaterials are discussed. Furthermore, oxidative stress, changes in steroid production and metabolic enzymes, organelle disruption, and alterations in signal pathways are introduced as potential mechanisms that may cause changes in hormone levels. Finally, we suggest that a risk assessment of endocrine toxicity based on standard procedures and consideration of endocrine disrupting effects of nanomaterials in the field and its environmental and population effects could be future research directions for endocrine toxicity of nanomaterials.

Emerging materials and technologies for landfill leachate treatment: A critical review

Sanitary landfill is the most popular way to dispose solid wastes with one major drawback: the generation of landfill leachate resulting from percolation of rainfall through exposed landfill areas or infiltration of groundwater into the landfill. The landfill leachate impacts on the environment has forced authorities to stipulate more stringent requirements for pollution control, generating the need for innovative technologies to eliminate waste degradation by-products incorporated in the leachate. Natural attenuation has no effect while conventional treatment processes are not capable of removing some the pollutants contained in the leachate which are reported to reach the natural environment, the aquatic food web, and the anthroposphere. This review critically evaluates the state-of-the-art engineered materials and technologies for the treatment of landfill leachate with the potential for real-scale application. The study outcomes confirmed that only a limited number of studies are available for providing new information about novel materials or technologies suitable for application in the removal of pollutants from landfill leachate. This paper focuses on the type of pollutants being removed, the process conditions and the outcomes reported in the literature. The emerging trends are also highlighted as well as the identification of current knowledge gaps and future research directions along with recommendations related to the application of available technologies for landfill leachate treatment.

Recent Advances in Functional Polymer Materials for Energy, Water, and Biomedical Applications: A Review

Academic research regarding polymeric materials has been of great interest. Likewise, polymer industries are considered as the most familiar petrochemical industries. Despite the valuable and continuous advancements in various polymeric material technologies over the last century, many varieties and advances related to the field of polymer science and engineering still promise a great potential for exciting new applications. Research, development, and industrial support have been the key factors behind the great progress in the field of polymer applications. This work provides insight into the recent energy applications of polymers, including energy storage and production. The study of polymeric materials in the field of enhanced oil recovery and water treatment technologies will be presented and evaluated. In addition, in this review, we wish to emphasize the great importance of various functional polymers as effective adsorbents of organic pollutants from industrial wastewater. Furthermore, recent advances in biomedical applications are reviewed and discussed.

Role of Defect Engineering and Surface Functionalization in the Design of Carbon Nanotube-Based Nitrogen Oxide Sensors

Nitrogen oxides (NOx) are among the main atmospheric pollutants; therefore, it is important to monitor and detect their presence in the atmosphere. To this end, low-dimensional carbon structures have been widely used as NOx sensors for their outstanding properties. In particular, carbon nanotubes (CNTs) have been widely used as toxic-gas sensors owing to their high specific surface area and excellent mechanical properties. Although pristine CNTs have shown promising performance for NOx detection, several strategies have been developed such as surface functionalization and defect engineering to improve the NOx sensing of pristine CNT-based sensors. Through these strategies, the sensing properties of modified CNTs toward NOx gases have been substantially improved. Therefore, in this review, we have analyzed the defect engineering and surface functionalization strategies used in the last decade to modify the sensitivity and the selectivity of CNTs to NOx. First, the different types of surface functionalization and defect engineering were reviewed. Thereafter, we analyzed experimental, theoretical, and coupled experimental-theoretical studies on CNTs modified through surface functionalization and defect engineering to improve the sensitivity and selectivity to NOx. Finally, we presented the conclusions and the future directions of modified CNTs as NOx sensors.

A review on graphitic carbon nitride (g-C3N4) based hybrid membranes for water and wastewater treatment

Graphitic carbon nitride (g-C₃N₄) has gained enormous attention for water and wastewater treatment. Compared with g-C₃N₄ nanopowders, g-C₃N₄ based hybrid membranes have demonstrated great potential for its superior practicability. This review outlines the preparation and characterization of g-C₃N₄ based hybrid membranes and presents their representative applications in water and wastewater treatment (e.g., removal of organic dyes, phenolic compounds, pharmaceuticals, salt ions, heavy metals, and oils). Meanwhile, g-C₃N₄ based films for the removal of contaminants through photocatalytic degradation is also summarized. In addition, the corresponding mechanisms and relevant findings are discussed. Finally, the challenges and research needs in the future and application of g-C₃N₄ based hybrid membranes are highlighted.

Functionalized carbon nanotubes: synthesis, properties and applications in water purification, drug delivery, and material and biomedical sciences

Carbon nanotubes (CNTs) are considered as one of the ideal materials due to their high surface area, high aspect ratio, and impressive material properties, such as mechanical strength, and thermal and electrical conductivity, for the manufacture of next generation composite materials. In spite of the mentioned attractive features, they tend to agglomerate due to their inherent chemical structure which limits their application. Surface modification is required to overcome the agglomeration and increase their dispersability leading to enhanced interactions of the functionalized CNTs with matrix materials/polymer matrices. Recent developments concerning reliable methods for the functionalization of carbon nanotubes offer an additional thrust towards extending their application areas. By chemical functionalization, organic functional groups are generated/attached to the surfaces as well as the tip of CNTs which opens up the possibilities for tailoring the properties of nanotubes and extending their application areas. Different research efforts have been devoted towards both covalent and non-covalent functionalization for different applications. Functionalized CNTs have been used successfully for the development of high quality nanocomposites, finding wide application as chemical and biological sensors, in optoelectronics and catalysis. Non covalently functionalized carbon nanotubes have been used as a substrate for the immobilization of a large variety of biomolecules to impart specific recognition properties for the development of miniaturized biosensors as well as designing of novel bioactive nanomaterials. Functionalized CNTs have also been demonstrated as one of the promising nanomaterials for the decontamination of water due to their high adsorption capacity and specificity for various contaminants. Specifically modified CNTs have been utilized for bone tissue engineering and as a novel and versatile drug delivery vehicle. This review article discusses in short the synthesis, properties and applications of CNTs. This includes the need for functionalization of CNTs, methods and types of functionalization, and properties of functionalized CNTs and their applications especially with respect to material and biomedical sciences, water purification, and drug delivery systems.

Catalytic degradation of acetaminophen by Fe and N Co-doped multi-walled carbon nanotubes

An Fe and N co-doped carbon nanotube (CNT) (Fe/N-CNT) was successfully prepared using a simple hydrothermal method. CNT, Fe doped CNTs (Fe-CNT), N doped CNTs (N-CNT), and Fe/N-CNT were characterized using scanning electron microscopy, X-ray photoelectron spectroscopy, Raman spectroscopy, and zeta potential analysis. The catalytic activities of the materials were investigated via pharmaceutical (acetaminophen, ACT) degradation using persulfate (PS). The ACT removal rate was in the order: Fe-CNT > N-CNT > Fe-CNT > CNT, for 30 min with 10 mg/L ACT, 0.05 g/L materials, and 0.08 mM PS. The doped N existed as pyridinic-N, pyrrolic-N/N-Fe, graphitic-N, and oxidized-N, while the doped Fe existed as Fe-N, FeO/Fe₃O₄, and Fe₂O₃/FeOOH at the edge. The rates of ACT removal and PS decomposition were well correlated with pyrrolic-N/N-Fe. The ACT removal in the Fe/N-CNT + PS system was as high as >98.4% and was not significantly affected by the initial pH of 2.0-8.2 and ten consecutive uses. However, natural organic matter (NOM) inhibited ACT removal by the accumulation on Fe/N-CNT. The results of ACT removal in the presence of radical scavengers, PS decomposition, and cyclic voltammetry showed that the ACT removal was dominantly attributed to a non-radical pathway with the accelerated electron transfer from ACT to PS through the Fe/N-CNT. The results in this study strongly suggest that the Fe/N-CNT + PS system is an excellent process for the degradation of refractory organic pollutants in various water matrices with improved performance and stability attributed by non-radical pathway.

Recent Progress in Superhydrophilic Carbon-Based Composite Membranes for Oil/Water Emulsion Separation

The purification of stabilized oil/water emulsions is essential to meet the ever increasing demand for monitoring water in the environment, which has been addressed with superwetting carbon-based separation membranes. These include superhydrophilic carbon-based membranes whose progress in recent years and perspectives are reviewed in this paper. The membrane construction strategy is organized into four parts, vacuum-assisted self-assembly, sol-gel process, electrospinning, and vacuum-assisted filtration. In each section, the design strategies and their responding disadvantages have been comprehensively discussed. The challenges and prospects concerning the superhydrophilic carbon-based separation membranes for oily wastewater purification are also summarized to arouse researchers to carry out more studies.

Advanced super-hydrophobic polymer-based porous absorbents for the treatment of oil-polluted water

The threat of environmental pollution caused by spilled oil is rapidly increasing along with the expansion of oil exploration, the development of maritime activities and industrial growth. Oil spill incidents usually affect seriously the ecosystem and human life. Therefore, the treatment and recovery of the oil spill have been considered as an ultra-important issue to protect the environment and to minimize its negative impacts on socio-economic activities. Among methods of oil spill recovery, porous materials have emerged as potential absorbents possessing the capacity of absorbing spilled oil at a fast rate, high adsorption capacity, good selectivity, and high reusability. In this review paper, two types of polymer-based porous absorbents modified surface and structure were introduced for the treatment strategy of the oil-polluted water. In addition, the absorption mechanism and factors affecting the adsorption capacity for oils and organic solvents were thoroughly analyzed. More importantly, characteristics of polymer-based porous materials were discussed in detail based on microstructure analysis, absorption efficiency, and reusability. In general, this paper has provided an overview and a comprehensive assessment of the use of advanced polymer-based porous materials for the treatment of oil-polluted water, although the impacts of environmental factors such as wind, wave, and temperature should be further investigated in the future.

Molecular dynamics simulation for membrane separation and porous materials: A current state of art review

Computational frameworks have been under specific attention within the last two decades. Molecular Dynamics (MD) simulations, identical to the other computational approaches, try to address the unknown question, lighten the dark areas of unanswered questions, to achieve probable explanations and solutions. Owing to their complex microporous structure on one side and the intricate biochemical nature of various materials used in the structure, separative membrane materials possess peculiar degrees of complications. More notably, as nanocomposite materials are often integrated into separative membranes, thin-film nanocomposites and porous separative nanocomposite materials could possess an additional level of complexity with regard to the nanoscale interactions brought to the structure. This critical review intends to cover the recent methods used to assess membranes and membrane materials. Incorporation of MD in membrane technology-related fields such as desalination, fuel cell-based energy production, blood purification through hemodialysis, etc., were briefly covered. Accordingly, this review could be used to understand the current extent of MD applications for separative membranes. The review could also be used as a guideline to use the proper MD implementation within the related fields.

The Role of Carbon Nanotube Pretreatments in the Adsorption of Benzoic Acid

Four different types of multi-walled carbon nanotubes (MWCNTs) were used and compared for the treatment of benzoic acid contaminated water. The types of nanotubes used were: (1) non-purified (CNTs^UP), as made; (2) purified (CNTs^P), not containing the catalyst; (3) oxidized (CNTs^OX), characterized by the presence of groups such as, –COOH; (4) calcined (CNTs⁹⁰⁰), with elimination of interactions between nanotubes. In addition, activated carbon was also used to allow for later comparison. The adsorption tests were conducted on an aqueous solution of benzoic acid at concentration of 20 mg/L, as a model of carboxylated aromatic compounds. After the adsorption tests, the residual benzoic acid concentrations were measured by UV-visible spectrometry, while the carbon nanotubes were characterized by TG and DTA thermal analyses and electron microscopy (SEM). The results show that the type of nanotubes thermally treated at 900 °C has the best performances in terms of adsorption rate and amounts of collected acid, even if compared with the performance of activated carbons.

Differentiating Solutes with Precise Nanofiltration for Next Generation Environmental Separations: A Review

Selective removal or enrichment of targeted solutes including micropollutants, valuable elements, and mineral scalants from complex aqueous matrices is both challenging and pivotal to the success of water purification and resource recovery from unconventional water resources. Membrane separation with precision at the subnanometer or even subangstrom scale is of paramount importance to address those challenges via enabling "fit-for-purpose" water and wastewater treatment. So far, researchers have attempted to develop novel membrane materials with precise and tailored selectivity by tuning membrane structure and chemistry. In this critical review, we first present the environmental challenges and opportunities that necessitate improved solute-solute selectivity in membrane separation. We then discuss the mechanisms and desired membrane properties required for better membrane selectivity. On the basis of the most recent progress reported in the literature, we examine the key principles of material design and fabrication, which create membranes with enhanced and more targeted selectivity. We highlight the important roles of surface engineering, nanotechnology, and molecular-level design in improving membrane selectivity. Finally, we discuss the challenges and prospects of highly selective NF membranes for practical environmental applications, identifying knowledge gaps that will guide future research to promote environmental sustainability through more precise and tunable membrane separation.

Ultrasonically Induced Polymerization and Polymer Grafting in the Presence of Carbonaceous Nanoparticles

Nanotechnology refers to technologies using at least one nanometric dimension. Most advances have been in the field of nanomaterials used in research and industry. The vast potential of polymeric nanocomposites for advanced materials and applications such as hybrid nanocomposites with customized electrical conductivity, anti-bacterial, anti-viral, and anti-fog properties have attracted considerable attention. The number of studies on the preparation of nanocomposites in the presence of carbon materials, i.e., carbon nanotubes (CNTs) and graphene, has intensified over the last decade with the growing interest in their outstanding synergic properties. However, the functionality of such nanocomposites depends on overcoming three key challenges: (a) the breakdown of nanoparticle agglomerates; (b) the attachment of functional materials to the nanoparticle surfaces; and (c) the fine dispersion of functional nanoparticles within the polymeric matrices. Ultrasonic polymerization and grafting in the presence of nanoparticles is an innovative solution that can meet these three challenges simultaneously. These chemical reactions are less well known and only a few research groups have dealt with them to date. This review focuses on two main pathways to the design of ultrasonically induced carbon-based nanocomposites: the covalent approach which is based on the chemical interactions between the carbon fillers and the matrix, and the non-covalent approach which is based on the physical interactions.

Swelling properties of graphite oxides and graphene oxide multilayered materials

Graphite oxide (GtO) and graphene oxide (GO) multilayered laminates are hydrophilic materials easily intercalated by water and other polar solvents. By definition, an increase in the volume of a material connected to the uptake of a liquid or vapour is named swelling. Swelling is a property which defines graphite oxides and graphene oxides. Less oxidized materials not capable of swelling should be named oxidized graphene. The infinite swelling of graphite oxide yields graphene oxide in aqueous dispersions. Graphene oxide sheets dispersed in a polar solvent can be re-assembled into multilayered structures and named depending on applications as films, papers or membranes. The multilayered GO materials exhibit swelling properties which are mostly similar to those of graphite oxides but not identical and in some cases surprisingly different. Swelling is a key property of GO materials in all applications which involve the sorption of water/solvents from vapours, immersion of GO into liquid water/solvents and solution based chemical reactions. These applications include sensors, sorption/removal of pollutants from waste waters, separation of liquid and gas mixtures, nanofiltration, water desalination, water-permeable protective coatings, etc. Swelling defines the distance between graphene oxide sheets in solution-immersed GO materials and the possibility for penetration of ions and molecules inside of interlayers. A high sorption capacity of GO towards many molecules and cations is defined by swelling which makes the very high surface area of GO accessible. GtO and GO swelling is a surprisingly complex phenomenon which is manifested in a variety of different ways. Swelling is strongly different for materials produced using the most common Brodie and Hummers oxidation procedures; it depends on the degree of oxidation, ad temperature and pressure conditions. The value of the GO interlayer distance is especially important in membrane applications. Diffusion of solvent molecules and ions is defined by the size of "permeation channels" provided by the swelled GO structure. According to extensive studies performed over the last decade the exact value of the inter-layer distance in swelled GO depends on the nature of solvent, temperature and pressure conditions, and the pH and concentration of solutions and exhibits pronounced aging effects. This review provides insight into the fundamental swelling properties of multilayered GO and demonstrates links to advanced applications of these materials.

Vertically Aligned Carbon Nanotube Membranes: Water Purification and Beyond

Vertically aligned carbon nanotube (VACNT) membranes have attracted significant attention for water purification owing to their ultra-high water permeability and antibacterial properties. In this paper, we critically review the recent progresses in the synthesis of VACNT arrays and fabrication of VACNT membrane methods, with particular emphasis on improving water permeability and anti-biofouling properties. Furthermore, potential applications of VACNT membranes other than water purification (e.g., conductive membranes, electrodes in proton exchange membrane fuel cells, and solar electricity–water generators) have been introduced. Finally, future outlooks are provided to overcome the limitations of commercialization and desalination currently faced by VACNT membranes. This review will be useful to researchers in the broader scientific community as it discusses current and new trends regarding the development of VACNT membranes as well as their potential applications.

Recent Developments in Nanomaterials-Modified Membranes for Improved Membrane Distillation Performance

Membrane distillation (MD) is a thermally induced membrane separation process that utilizes vapor pressure variance to permeate the more volatile constituent, typically water as vapor, across a hydrophobic membrane and rejects the less volatile components of the feed. Permeate flux decline, membrane fouling, and wetting are some serious challenges faced in MD operations. Thus, in recent years, various studies have been carried out on the modification of these MD membranes by incorporating nanomaterials to overcome these challenges and significantly improve the performance of these membranes. This review provides a comprehensive evaluation of the incorporation of new generation nanomaterials such as quantum dots, metalloids and metal oxide-based nanoparticles, metal organic frameworks (MOFs), and carbon-based nanomaterials in the MD membrane. The desired characteristics of the membrane for MD operations, such as a higher liquid entry pressure (LEPw), permeability, porosity, hydrophobicity, chemical stability, thermal conductivity, and mechanical strength, have been thoroughly discussed. Additionally, methodologies adopted for the incorporation of nanomaterials in these membranes, including surface grafting, plasma polymerization, interfacial polymerization, dip coating, and the efficacy of these modified membranes in various MD operations along with their applications are addressed. Further, the current challenges in modifying MD membranes using nanomaterials along with prominent future aspects have been systematically elaborated.

Tailored CNTs Buckypaper Membranes for the Removal of Humic Acid and Separation of Oil-in-Water Emulsions

Carbon nanotubes (CNTs) are a robust material and proven as a promising candidate for a wide range of electronic, optoelectronic and environmental applications. In this work, two different methods were utilized for the preparation of CNTs exhibiting different aspect ratios via chemical vapor deposition (CVD). The as-prepared CNTs were analyzed using scanning electron microscopy (SEM), transmission electron microscopy (TEM), N₂adsorption isotherms, thermogravimetric analysis and Raman spectroscopy in order to investigate their morphological and structural properties. Free-standing CNTs "buckypaper" membranes were fabricated, characterized and tailored to meet the requirements of two applications, i.e., (1) the removal of humic acid (HA) from water and (2) separation of oil-in-water emulsions. It was revealed that the hydrophobic buckypapers showed high separation performance for Shell oil-in-water emulsions filtration, with up to 98% through the accumulation of oil droplets onto the membrane surface. The absorption capacity of buckypaper membranes for various organic liquids (oil, chloroform and toluene) was evaluated over 10 absorption cycles to investigate their recyclability and robustness. Moreover, surface modification was introduced to the pristine CNTs to increase their surface hydrophilicity and improve the pure water permeability of buckypapers. These modified buckypapers showed high flux for HA solutions and excellent HA rejection efficiency up to 95%via size exclusion and electrostatic repulsion mechanisms.

Solvation-Involved Nanoionics: New Opportunities from 2D Nanomaterial Laminar Membranes

Nanoporous laminar membranes composed of multilayered 2D nanomaterials (2D-NLMs) are increasingly being exploited as a unique material platform for understanding solvated ion transport under nanoconfinement and exploring novel nanoionics-related applications, such as ion sieving, energy storage and harvesting, and in other new ionic devices. Here, the fundamentals of solvation-involved nanoionics in terms of ionic interactions and their effect on ionic transport behaviors are discussed. This is followed by a summary of key requirements for materials that are being used for solvation-involved nanoionics research, culminating in a demonstration of unique features of 2D-NLMs. Selected examples of using 2D-NLMs to address the key scientific problems related to nanoconfined ion transport and storage are then presented to demonstrate their enormous potential and capabilities for nanoionics research and applications. To conclude, a personal perspective on the challenges and opportunities in this emerging field is presented.

Single and binary protein electroultrafiltration using poly(vinyl-alcohol)-carbon nanotube (PVA-CNT) composite membranes

Electrically conductive composite ultrafiltration membranes composed of carbon nanotubes have exhibited efficient fouling inhibition in wastewater treatment applications. In the current study, poly(vinyl-alcohol)-carbon nanotube membranes were applied to fed batch crossflow electroultrafiltration of dilute (0.1 g/L of each species) single and binary protein solutions of α-lactalbumin and hen egg-white lysozyme at pH 7.4, 4 mM ionic strength, and 1 psi. Electroultrafiltration using the poly(vinyl-alcohol)-carbon nanotube composite membranes yielded temporary enhancements in sieving for single protein filtration and in selectivity for binary protein separation compared to ultrafiltration using the unmodified PS-35 membranes. Assessment of membrane fouling based on permeate flux, zeta potential measurements, and scanning electron microscopy visualization of the conditioned membranes indicated significant resulting protein adsorption and aggregation which limited the duration of improvement during electroultrafiltration with an applied cathodic potential of -4.6 V (vs. Ag/AgCl). These results imply that appropriate optimization of electroultrafiltration using carbon nanotube-deposited polymeric membranes may provide substantial short-term improvements in binary protein separations.