Deep Eutectic Solvents for Pretreatment, Extraction, and Catalysis of Biomass and Food Waste

The Physicochemical Properties and Plausible Implication of Deep Eutectic Solvents in Analytical Techniques

Volatile organic solvents and fluoride-containing ionic liquids (ILs) have few drawbacks like toxicity, non-biodegradability, and environmental issues. Even though ILs are considered as new safest solvent for their lower volatility. They pose toxicity and sustainability concerns. Deep eutectic solvents (DESs) have garnered significant attention as substitutes for these solvents, addressing their drawbacks and aligning with specific principles of green chemistry, such as reduced toxicity, biodegradability, and the use of renewable resources. This review thoroughly explains the emergence and inception of DESs through their development. It deals with the physicochemical properties like density, polarity, and viscosity. The factors dealing with variation in density and viscosity of DES have been discussed. The preparation and operation of DESs, encompassing their various variants such as hydrophobic and hydrophilic types are examined to provide a comprehensive grasp of their chemical properties. Beyond basic characteristics, the article delves into a few specific DES applications to demonstrate their flexibility. DESs show promising multifarious utility, ranging from acting as extractant to critical roles in sorbent-based extractions, solvent-based extractions, and their role in various analytical techniques. The article covers the opportunities and difficulties associated with DESs, offering a prospective viewpoint on future advancements and difficulties. The review outlines different facets of DES research, emphasizing the level of knowledge at the moment and their potential influence in the emerging subject of DESs.

Valorization of wheat straw through enhancement of cellulose accessibility, xylan elimination and lignin removal by choline chloride:p-toluenesulfonic acid pretreatment

Different molar ratio of choline chloride (ChCl) and p-toluenesulfonic acid (p-TsOH) (2:1, 1:1 and 1:2, mol:mol) were used to prepare deep eutectic solvents (ChCl:p-TsOH) for pretreating cellulose fibers to elevate cellulose accessibility, enhance xylan elimination, increase lignin removal and promote enzymatic digestion. ChCl:p-TsOH (1:1, mol:mol) could effectually destroy the dense layout of wheat straw (WS) at 80 °C for 60 min. Cellulose crystallinity declined from 43.4 % to 25.5 %, and the lignin surface area and hydrophobicity were reduced to 182.6 m2/g and 3.2 L/g, respectively. While cellulose accessibility in WS was significantly improved to 523.9 mg/g. The delignification and xylan removal reached 72.4 % and 90.5 %, respectively. The enzymatic digestibility reached 89.3 %. Furthermore, molecular dynamics simulation and quantum chemistry calculation were conducted on the lignocellulose model. The van der Waals interaction between ChCl:p-TsOH and lignin and the dispersion interaction between ChCl and lignin were identified. Accordingly, the interaction between biomass and ChCl:p-TsOH was elucidated at the molecular level. It provided a comprehensive understanding of lignocellulosic biomass valorization through the highly efficient pretreatment by ChCl:p-TsOH.

Retrieval of Polyphenols Using Aqueous Two-Phase Systems Based on Ethyl Lactate and Organic Salts

Food waste remains a critical global concern, with approximately one third of all food produced being ultimately discarded. Therefore, it is urgent to develop new techniques for the effective repurpose of waste. Aqueous two-phase systems (ATPSs) stand out as a simple and biocompatible liquid-liquid extraction technique for the recovery of bioactive substances from food waste. In ATPSs, the target species partition between two liquid phases, according to affinity, which facilitates its extraction. This work aimed at extracting three polyphenols-chlorogenic acid (CA), ferulic acid (FA), and resveratrol (RV)-through the application of eco-friendly ATPSs composed of water, ethyl lactate (EL), and organic salts, namely disodium succinate (Na2Succinate) and disodium tartrate (Na2Tartrate), for future application in the valorisation of food waste. All partitions presented successful results, with values of partition coefficients (K) higher than 1 and extraction efficiencies (E) higher than 50%, indicating a preferential migration of the polyphenols to the top phase. The extraction of FA using the ATPS based on Na2Tartrate presented the most promising results, with K = 19 ± 6 and E = (94.2 ± 0.9)% for the longest tie-line. Additionally, a comparison with previous works of the research group was drawn, with the extraction of RV exhibiting outstanding performance across all studied ATPSs. Therefore, the assessed ATPSs were shown to hold immense potential for the recovery of polyphenols.

Active Water Optimization in Different Electrolyte Systems for Stable Zinc Anodes

Zinc (Zn) metal, with abundant resources, intrinsic safety, and environmental benignity, presents an attractive prospect as a novel electrode material. However, many substantial challenges remain in realizing the widespread application of aqueous Zn-ion batteries (AZIBs) technologies. These encompass significant material corrosion challenges (This can lead to battery failure in an unloaded state.), hydrogen evolution reactions, pronounced dendrite growth at the anode interface, and a constrained electrochemical stability window. Consequently, these factors contribute to diminished battery lifespan and energy efficiency while restricting high-voltage performance. Although numerous reviews have addressed the potential of electrode and separator design to mitigate these issues to some extent, the inherent reactivity of water remains the fundamental source of these challenges, underscoring the necessity for precise regulation of active water molecules within the electrolyte. In this review, the failure mechanism of AZIBs (unloaded and in charge and discharge state) is analyzed, and the optimization strategy and working principle of water in the electrolyte are reviewed, aiming to provide insights for effectively controlling the corrosion process and hydrogen evolution reaction, further controlling dendrite formation, and expanding the range of electrochemical stability. Furthermore, it outlines the challenges to promote its practical application and future development pathways.

Deep Eutectic Solvents based green approach for bioactive molecules recovery from Spirulina

Spirulina is a unicellular microalga, characterized by blue/green color, that has received significant attention for its interesting nutritional composition. Phenolic compounds and phycocyanin (PC) are responsible for the many biological activities of Spirulina. Spirulina phenolic compounds are usually extracted using organic solvents, while PC is extracted with water or phosphate buffer solution, obtaining an extract characterized by low stability and low purity. Deep Eutectic Solvents (DESs) are green solvents, widely applied for bioactive molecules extraction, composed by two or more molecules which act as hydrogen bond acceptor or hydrogen bond donor to create an eutectic mixture. A Natural Deep Eutectic Solvent (NADES), is a DES composed only by natural compounds. This work aimed to optimize a green extraction procedure based on NADES to obtain an extract rich in phenolic compounds and PC from Spirulina. The application of NADESs as extraction solvents is an important strategy for recovering phenolic compounds and to increase and stabilize the protein PC. The optimized extraction procedure involved to use a betaine-glucose NADES under the following conditions: matrix-to-solvent ratio of 1:20 (w/w), temperature of 50 °C and one hour as extraction time. The developed extraction procedure guaranteed to recover a phenolic compounds and PC quantity of 11.77 ± 1.23 mg GAE (gallic acid equivalents) and 27.56 ± 2.46 g per g of Spirulina powder respectively. PC in the NADES extract degraded more slowly than in an aqueous extract. The extract phenolic compounds profile was determined through high performance liquid chromatography coupled with mass spectrometry analysis.

Pretreatment of Vine Shoot Biomass by Choline Chloride-Based Deep Eutectic Solvents to Promote Biomass Fractionation and Enhance Sugar Production

Vine shoots hold promise as a biomass source for fermentable sugars with efficient fractionation and conversion processes. The study explores vine shoots as a biomass source for fermentable sugars through pretreatment with two deep eutectic solvents mixtures: choline chloride:lactic acid 1:5 (ChCl:LA) and choline chloride:ethylene glycol 1:2 (ChCl:EG). Pretreatment conditions, such as temperature/time, solid/liquid ratio, and biomass particle size, were studied. Chemical composition, recovery yields, delignification extent, and carbohydrate conversion were evaluated, including the influence of washing solvents. Temperature and particle size notably affected hemicellulose and lignin dissolution, especially with ChCl:LA. Pretreatment yielded enriched cellulose substrates, with high carbohydrate conversion rates up to 75.2% for cellulose and 99.9% for xylan with ChCl:LA, and 54.6% for cellulose and 60.2% for xylan with ChCl:EG. A 50% acetone/water mixture increased the delignification ratios to 31.5%. The results underscore the potential of this pretreatment for vine shoot fractionation, particularly at 30% solid load, while acknowledging the need for further process enhancement.

Reactive Eutectic Media for Lignocellulosic Biomass Fractionation

This study introduces an alternative approach towards lignocellulosic biomass fractionation. For this purpose, reactive eutectic media (REM) based on ammonium formate and different organic acids are investigated, possible products are identified, and the REM are employed for lignin extraction and terminal isolation of cellulose pulp from beech wood. The method promises a considerable process intensification by simultaneous separation of high purity cellulose pulp, lignin isolation as a cationically modified species, and production of value-added chemicals from reaction products of the REM. This study puts a further focus on the generated cellulose pulp and investigates it with respect to surface charge and fiber length.

Progress in the Sustainable Development of Biobased (Nano)materials for Application in Water Treatment Technologies

Water pollution remains a widespread problem, affecting the health and wellbeing of people around the globe. While current advancements in wastewater treatment and desalination show promise, there are still challenges that need to be overcome to make these technologies commercially viable. Nanotechnology plays a pivotal role in water purification and desalination processes today. However, the release of nanoparticles (NPs) into the environment without proper safeguards can lead to both physical and chemical toxicity. Moreover, many methods of NP synthesis are expensive and not environmentally sustainable. The utilization of biomass as a source for the production of NPs has the potential to mitigate issues pertaining to cost, sustainability, and pollution. The utilization of biobased nanomaterials (bio-NMs) sourced from biomass has garnered attention in the field of water purification due to their cost-effectiveness, biocompatibility, and biodegradability. Several research studies have been conducted to efficiently produce NPs (both inorganic and organic) from biomass for applications in wastewater treatment. Biosynthesized materials such as zinc oxide NPs, phytogenic magnetic NPs, biopolymer-coated metal NPs, cellulose nanocrystals, and silver NPs, among others, have demonstrated efficacy in enhancing the process of water purification. The utilization of environmentally friendly NPs presents a viable option for enhancing the efficiency and sustainability of water pollution eradication. The present review delves into the topic of biomass, its origins, and the methods by which it can be transformed into NPs utilizing an environmentally sustainable approach. The present study will examine the utilization of greener NPs in contemporary wastewater and desalination technologies.

Enhancing deep eutectic solvent systems for efficient fermentable sugar recovery from lignocellulosic fiber

Efficient conversion of sugars into fermentable sugars is a critical challenge in the cost-effective production of lignocellulosic biopolymers and biofuels. This study focuses on various sugar quantification techniques applied to Furcraea Foetida (Mauritius Hemp) samples, utilizing natural deep eutectic solvents (NADES) and deep eutectic solvents (DES) like urea, glycerol, citrates, pyrogallol (PY), and cetyltrimethylammonium bromide (CTAB). Employing a Taguchi-designed experiment, operational conditions were fine-tuned to evaluate the influence of time, concentration, and temperature on each deep eutectic solvent-based process. The emerging green solvent extraction approach demonstrated significant results, achieving notably high sugar yields compared to traditional techniques such as alkali, hot-water, and acid-mediated extraction. At a CTAB:PY molar ratio of 1:3, optimized for 60 min at 50 °C, the highest fermentable sugar (FS) yield of 0.6891 ± 0.0123 g FS/g LCB was attained-2 to 6 times higher than non-optimized values and 0.2 to 0.3 times higher than optimized traditional methods. In light of this, this research study emphasizes the pivotal significance of efficient sugar conversion through optimized deep eutectic solvent-based extraction methods, with a particular focus on Furcraea Foetida fibers, offering promising outcomes for the biofuel and biopolymer production industry.

Current progress and future perspective of microalgae biomass pretreatment using deep eutectic solvents

Pretreatment process is considered as the most important step for effective microalgae biomass refining and has gained more interest since last decades. However, the main obstacles to commercialize microalgae products are recalcitrant cell wall and lack of cost-effective, green, and sustainable pretreatment approaches. Till now, various microalgae pretreatment approaches have been applied prior to extraction steps to enhance the accessibility of solvent inside the cells. However, high energy consumption and the hazardousness of solvents are considerable problem for these pretreatment methods. In this regard, deep eutectic solvents are recognized as sustainable and green solvents possessing great potential for microalgae biomass processing due to their low toxicity, low cost, biodegradability, easy recycling, and reuse. This article provides the fundamentals of DES composition, synthesis, properties, and the current advances in the application of microalgae biomass process.

Deep eutectic solvents: Preparation, properties, and food applications

Deep Eutectic Solvents (DESs) emerge as innovative 21st-century solvents, supplanting traditional ones like ethanol and n-hexane. Renowned for their non-toxic, biodegradable, and water-miscible nature with reduced volatility, DESs are mostly synthesized through heating and stirring method. Physicochemical properties such as polarity, viscosity, density and surface tension of DESs influenced their application. This review paper gives the overview of application of eco-benign DESs in fruits, vegetables, cereals, pulses, spices, herbs, plantation crops, oil seed crops, medicinal and aromatic plants, seaweed, and milk for the extraction of bioactive compounds. Also, it gives insight of determination of pesticides, insecticides, hazardous and toxic compounds, removal of heavy metals, detection of illegal milk additive, purification of antibiotics and preparation of packaging film. Methodologies for separating bioactive compounds from DESs extracts are systematically examined. Further, safety regulations of DESs are briefly discussed and reviewed literature reveals prevalent utilization of DES-based bioactive compound rich extracts in cosmetics, indicating untapped potential of their application in the food industry.

Spectroscopic and Computational Study of ZnCl2-Methanol Low-Melting-Temperature Mixtures

Alcoholic electrolyte mixtures have wide applications in industries. In this study, a series of mixtures composed of ZnCl2 and methanol (MeOH) with ZnCl2 mol % from 6.7 to 25 were prepared, and their spectral, structural, and thermodynamic properties were studied using infrared (IR) spectroscopy, differential scanning calorimetry (DSC), and density functional theory (DFT) calculations. The DFT-assisted analysis of excess spectra, supported by 2D-correlation spectroscopy, led to the identification of the major constituents of ZnCl2-MeOH mixtures, namely, MeOH monomer, MeOH dimer, and ZnCl2-3MeOH complex, produced after dissociation of MeOH trimer which represents the bulk methanol. The Hirshfeld charge analysis showed that in the competition between the O-H···Cl hydrogen bond (H-bond) and Zn ← O coordination bond to transfer charge in ZnCl2-MeOH complexes, the latter always dominates, making MeOH positively charged. The phase diagram of the binary system showed the presence of V-shaped glass transition temperatures (Tg), characteristic of low-melting mixture solvents (LoMMSs). The present study provides insights into the microscopic properties of the system and sheds light on the understanding of the general principles to prepare deep-eutectic solvents (DESs) or LoMMSs using inorganic salts and alcoholic compounds.

Eco-Friendly and Efficient Extraction of Polysaccharides from Acanthopanax senticosus by Ultrasound-Assisted Deep Eutectic Solvent

A green extraction method was developed using deep eutectic solvent extraction for the polysaccharide from Acanthopanax senticosus (A. senticosus). Among the eight types of DES prepared, the DES with a ratio of 1:4 L-malic acid to L-proline was found to be a suitable extraction solvent based on the extraction efficiency. The extraction parameters were optimized by Plackett-Burman and response surface methodology (RSM). The best extraction conditions were found for L-malic acid. Under the conditions of an L-malic acid/L-proline ratio of 1:4, ultrasonic power of 240 W, material-liquid ratio of 31.068 g/mL, water content of 32.364%, extraction time of 129.119 min, and extraction temperature of 60 °C, the extraction rate of A. senticosus polysaccharides was 35.452 ± 0.388 mg-g-1. This rate was higher than that of polysaccharides obtained by hot water extraction (13.652 ± 0.09 mg-g-1). The experimental results were best fitted by the quasi-secondary kinetic model when compared to two other kinetic models. Electron microscopic observations showed that DESs were more destructive to plant cells. The polysaccharide extracted from DESs had more monosaccharide components, a lower molecular weight, a higher antioxidant capacity, and superior anti-glycation activity compared to polysaccharides extracted from water (ASPS-PW). This study demonstrates the effectiveness of DESs in obtaining polysaccharides from A. senticosus.

Deep eutectic solvents for the determination of endocrine disrupting chemicals

The harmful effects of endocrine disrupting chemicals (EDCs) to humans and other organisms in the environment have been well established over the years, and more studies are ongoing to classify other chemicals that have the potential to alter or disrupt the regular function of the endocrine system. In addition to toxicological studies, analytical detection systems are progressively being improved to facilitate accurate determination of EDCs in biological, environmental and food samples. Recent microextraction methods have focused on the use of green chemicals that are safe for analytical applications, and present very low or no toxicity upon disposal. Deep eutectic solvents (DESs) have emerged as one of the viable alternatives to the conventional hazardous solvents, and their unique properties make them very useful in different applications. Notably, the use of renewable sources to prepare DESs leads to highly biodegradable products that mitigate negative ecological impacts. This review presents an overview of both organic and inorganic EDCs and their ramifications on human health. It also presents the fundamental principles of liquid phase and solid phase microextraction methods, and gives a comprehensive account of the use of DESs for the determination of EDCs in various samples.

Menthol-Based (Deep) Eutectic Solvents: A Review on Properties and Application in Extraction

In the last 10 years the interest in deep eutectic solvents (DESs) as a new class of green solvents has considerably increased. The emergence of numerous of hydrophobic DESs has stimulated intensive research into their application in extraction technologies, including sample preparation. As the properties of such systems are highly dependent on the properties of their components (hydrogen bond donors and acceptors) and can be finely tuned, DESs can be successfully used for the extraction of both metal ions and organic substances, including biomolecules. Despite the rapidly increasing number of publications on the use of DESs as an extraction medium, including review articles, information on the extraction properties of DESs in terms of their chemical composition has not yet been summarized. This review covers available literature data on the physicochemical properties of menthol-based eutectic solvents and the results of their practical application as an extraction medium. Also, the appropriateness of using the term "DES" for all mixtures with melting points lower than the melting points of their components is discussed.

Physicochemical Properties of Choline Chloride/Acetic Acid as a Deep Eutectic Solvent and Its Binary Solutions with DMSO at 298.15 to 353.15 K

Deep eutectic solvents (DESs) are considered to play an important role in green chemistry and other technological fields as an alternative to organic solvents. The present study reports measurements of density (ρ), speed of sound (u), dynamic viscosity (η), and electrical conductivity (κ) and investigates physicochemical properties of choline chloride/acetic acid (ChCl/AcA DES) and its binary mixtures with dimethyl sulfoxide (DMSO) over the entire composition and temperature (298.15-353.15 K) range. The density data are well fitted by a second-degree polynomial equation in T. DES/DMSO mixtures exhibit negative excess molar volume and isentropic compressibility deviation with a minimum in respective curves at x1 ≈ 0.15 (x1 is the mole fraction of DES in the mixture), which became deeper with increasing temperature. The ChCl/AcA DES and DMSO curves for excess partial molar volume cross each other at x1 ≈ 0.15, showing that the packing effect is dominant over specific interactions. A similar behavior is observed for excess molar viscosity, showing the minima at x1 ≈ 0.62, and substantiates volumetric results. The temperature dependence of viscosity and conductivity is well described by the Vogel-Fulcher-Tammann (VFT) equation.

Extracting mycotoxins from edible vegetable oils by using green, ecofriendly deep eutectic solvents

In this work, we developed an environmentally friendly liquid-liquid microextraction method using a natural deep eutectic solvent in combination with liquid chromatography for the simultaneous determination of four mycotoxins (deoxynivalenol, alternariol, ochratoxin A and zearalenone) in edible vegetable oils. A chemometric approach assessed the effect of the operational parameters on the mycotoxin extraction efficiency. The extracts were analyzed by HPLC coupled with a diode array and fluorescence detector. The optimum NADES composition resulted in the highest extraction recoveries, and it was applied to coextract the target mycotoxins in several types of edible vegetable oils without using hazardous solvents or requiring further clean-up. The limits of detection ranged from 0.07 to 300 µg kg-1, and recoveries were close to 100%, except for zearalenone (viz. 35%), with relative standard deviations below 9% in all cases. The proposed method was validated following the European Commission 2002/657/EC and 2006/401/EC.

Effect of water addition on caprylic acid: Quaternary ammonium salts (QAS) deep eutectic solvents: Characterization of their structural and dynamical properties

Physicochemical properties of the binary mixtures based on Caprylic acid: Quaternary ammonium salts (QAS) (7:3 mol ratio) are investigated using MD simulations. Considering the hydrophobic character of eutectic solvents based on long-chain fatty acids, the stability of the binary mixtures was investigated in the adjacent water. In order to investigate the effect of water on intermolecular interactions in binary mixtures, the structural properties of the binary mixtures in the pure state and adjacent to water were investigated at 310 K. Assessed structural properties include the combined distribution functions (CDFs), the radial distribution functions (RDFs), the angular distribution functions (ADFs), and the Hydrogen bonding network between HBA and HBD and Spatial distribution functions (SDF). We aimed to represent the structural stability of eutectic solvents based on Caprylic acid and Quaternary ammonium salts (QAS) as a function of the alkyl chain length of cations, the evidence was found for the interaction between the chloride anion leads to the transition of HBA to the water-rich phase. The alkyl chain length of cations of Quaternary ammonium salts shows the stability of eutectic solvents in the adjacent water.

Exploitation of lignocellulosic-based biomass biorefinery: A critical review of renewable bioresource, sustainability and economic views

Urbanization has driven the demand for fossil fuels, however, the overly exploited resource has caused severe damage on environmental pollution. Biorefining using abundant lignocellulosic biomass is an emerging strategy to replace traditional fossil fuels. Value-added lignin biomass reduces the waste pollution in the environment and provides a green path of conversion to obtain renewable resources. The technology is designed to produce biofuels, biomaterials and value-added products from lignocellulosic biomass. In the biorefinery process, the pretreatment step is required to reduce the recalcitrant structure of lignocellulose biomass and improve the enzymatic digestion. There is still a gap in the full and deep understanding of the biorefinery process including the pretreatment process, thus it is necessary to provide optimized and adapted biorefinery solutions to cope with the conversion process in different biorefineries to further provide efficiency in industrial applications. Current research progress on value-added applications of lignocellulosic biomass still stagnates at the biofuel phase, and there is a lack of comprehensive discussion of emerging potential applications. This review article explores the advantages, disadvantages and properties of pretreatment methods including physical, chemical, physico-chemical and biological pretreatment methods. Value-added bioproducts produced from lignocellulosic biomass were comprehensively evaluated in terms of encompassing biochemical products , cosmetics, pharmaceuticals, potent functional materials from cellulose and lignin, waste management alternatives, multifunctional carbon materials and eco-friendly products. This review article critically identifies research-related to sustainability of lignocellulosic biomass to promote the development of green chemistry and to facilitate the refinement of high-value, environmentally-friendly materials. In addition, to align commercialized practice of lignocellulosic biomass application towards the 21st century, this paper provides a comprehensive analysis of lignocellulosic biomass biorefining and the utilization of biorefinery green technologies is further analyzed as being considered sustainable, including having potential benefits in terms of environmental, economic and social impacts. This facilitates sustainability options for biorefinery processes by providing policy makers with intuitive evaluation and guidance.

Lignocellulosic Biomass for the Fabrication of Triboelectric Nano-Generators (TENGs)-A Review

Growth in population and increased environmental awareness demand the emergence of new energy sources with low environmental impact. Lignocellulosic biomass is mainly composed of cellulose, lignin, and hemicellulose. These materials have been used in the energy industry for the production of biofuels as an eco-friendly alternative to fossil fuels. However, their use in the fabrication of small electronic devices is still under development. Lignocellulose-based triboelectric nanogenerators (LC-TENGs) have emerged as an eco-friendly alternative to conventional batteries, which are mainly composed of harmful and non-degradable materials. These LC-TENGs use lignocellulose-based components, which serve as electrodes or triboelectric active materials. These materials can be derived from bulk materials such as wood, seeds, or leaves, or they can be derived from waste materials from the timber industry, agriculture, or recycled urban materials. LC-TENG devices represent an eco-friendly, low-cost, and effective mechanism for harvesting environmental mechanical energy to generate electricity, enabling the development of self-powered devices and sensors. In this study, a comprehensive review of lignocellulosic-based materials was conducted to highlight their use as both electrodes and triboelectric active surfaces in the development of novel eco-friendly triboelectric nano-generators (LC-TENGs). The composition of lignocellulose and the classification and applications of LC-TENGs are discussed.

Factors Affecting the Extraction of (Poly)Phenols from Natural Resources Using Deep Eutectic Solvents Combined with Ultrasound-Assisted Extraction

Replacing conventional solvents with deep eutectic solvents (DES) has shown promising effects on the extraction yield of (poly)phenols. DES can be combined with ultrasound-assisted extraction (UAE) to further increase the extraction efficiency of (poly)phenols from natural resources compared to conventional methods. This review discusses the factors associated with DES (composition, solvent-to-sample ratio, extraction duration, and temperature) and UAE (ultrasound frequency, power, intensity, and duty cycle) methods that influence the extraction of (poly)phenols and informs future improvements required in the optimization of the extraction process. For the optimum (poly)phenol extraction from natural resources, the following parameters shall be considered: ultrasound frequency should be in the range of 20-50 kHz, ultrasound intensity in the range of 60-120 W/cm2, ultrasound duty cycle in the range of 40-80%, ultrasound duration for 10-30 minutes, and ultrasound temperature for 25-50 °C. Among the reported DES systems, choline chloride with glycerol or lactic acid, with a solvent-to-sample mass ratio of 10-30:1 shown to be effective. The solvent composition and solvent-to-sample mass ratio should be selected according to the target compound and the source material. However, the high viscosity of DES is among the major limitations. Optimizing these factors can help to increase the yield of extracted (poly)phenols and their applications.

Improved enzymatic saccharification of bulrush via an efficient combination pretreatment

Glycerol (Gly) was selected as hydrogen-bond-donor for preparing ChCl-based DES (ChCl:Gly), and the mixture of ChCl:Gly (20 wt%) and NaOH (4 wt%) was utilized for combination pretreatment of bulrush at 100 °C for 60 min (severity factor LogRo = 1.78). The effects of DES pretreatment on the chemical composition, microstructure, crystal structure, and cellulase hydrolysis were explored. NaOH-ChCl:Gly could remove lignin (80.1%) and xylan (66.8%), and the enzymatic digestibility of cellulose reached 87.9%. The accessibility of bulrush was apparently increased to 645.2 mg/g after NaOH-ChCl:Gly pretreatment. The hydrophobicity and lignin surface area were reduced to 1.56 L/g and 417 m2/g, respectively. The crystallinity of cellulose was increased from 20.8% to 55.6%, and great changes in surface morphology were observed, which explained the improvement of enzymatic hydrolysis efficiency. Overall, DES combined with alkali treatment could effectively promote the removal of lignin and xylan in bulrush, thus the relative saccharification activity was greatly affected.

NADES assisted integrated biorefinery concept for pectin recovery from kinnow (Citrus reticulate) peel and strategic conversion of residual biomass to L(+) lactic acid

The present study aims to establish an integrated strategy for valorization of kinnow peel waste. A total of ten natural deep eutectic solvents (NADESs) were exploited for extraction of pectin. The highest yield of pectin enriched material was reported 35.66 % w/dw using choline chloride-Maltose based NADES. The extraction process parameters and chemical composition of NADES influenced the yield and different associated physico-chemical attributes of the pectin enriched material. All the recovered pectin enriched materials found to be composed of low methoxy pectin (degree of methylation: 18.41-40.26 %) and galacturonic acid (GalA) content was in range of 67.56-78.22 %. The Principal Component Analysis (PCA) was used to categorise isolated pectin enriched materials based on similarities and differences. The liquid fraction upon pectin extraction presented a considerable amount of fermentable sugar which was further utilized for lactic acid production by microbial intervention. The microbial strain Lactobacillus amylophilus GV6 was exploited for lactic acid fermentation where the highest yield reached 55.59 g/L. A sustainable and straight-forward biorefinery concept was developed for extraction of pectin enriched material and lactic acid production from kinnow peel waste with potential application in food and biotechnological sectors.

Physicochemical and thermal characteristics of choline chloride-based deep eutectic solvents

It is essential to investigate the physicochemical and thermal properties of choline chloride (ChCl)-based deep eutectic solvents (DESs) as hydrogen bond acceptor (HBA) with various hydrogen bond donor (HBD) functional groups, such as α-hydroxy acid (lactic acid) or polyol (glycerol). It is important to consider how molar ratios impact these properties, as they may be altered for particular applications. This study aimed to examine the physicochemical and thermal properties of ChCl-based DESs with lactic acid (LA) or glycerol (Gly) at different molar ratios (1:2-1:10). The pH of ChCl:LA (0-1.0) is lower than that of ChCl:Gly (4.0-5.0) because of the hydrogen bonds between ChCl and LA. A higher amount of LA/Gly resulted in higher densities of ChCl:Gly (1.20-1.22 g cm-3) and ChCl:LA (1.16-1.19 g cm-3) due to the stronger hydrogen bonds and tighter packing of the molecules. The refractive index of ChCl:Gly (1.47-1.48) was higher than ChCl:LA (1.44-1.46), with a trend similar to density. The viscosities of ChCl:Gly (0.235-0.453 Pa s) and ChCl:LA (0.04-0.06 Pa s) increased with increasing LA/Gly molar ratio but decreased with temperature due to the high kinetic energy from heating, lowering the attractive forces between molecules. The activation energy for ChCl:LA (15.29-15.55 kJ mol-1) is greater than for ChCl:Gly (7.77-8.78 kJ mol-1), indicating that ChCl:LA has a greater viscosity-temperature dependence than ChCl:Gly. The DESs decomposition temperatures are 179.73-192.14 °C for ChCl:LA and 189.69-197.41 °C for ChCl:Gly. Freezing temperatures are correlated with the molecular weight of HBDs, with lower values causing a larger decrease in freezing temperatures. The interactions of polyols with anions were stronger than those of α-hydroxy acids with anions. The variations in HBA to HBD molar ratios affected DESs properties, providing a fundamental understanding of the properties critical for their diverse applications.

Comprehensive understanding of enzymatic saccharification of Betaine:Lactic acid-pretreated sugarcane bagasse

Green solvents, especially deep eutectic solvents (DESs), are widely applied to pretreat biomass for enhancing its enzymatic hydrolysis. In this work, lactic acid was selected as the hydrogen-bond-donor to prepare Betaine-base DES (Betaine:LA), The DES was utilized to pretreat sugarcane bagasse (SCB) at 160 ℃ for 80 min (severity factor LogR0 = 3.67). The influences of Betaine:LA treatment on the chemical composition, crystal and microstructure structure of cellulose, and cellulase digestion were investigated. The results showed that the lignin (47.1%) and xylan (44.6%) were removed, the cellulase digestibility of Betaine:LA-treated SCB was 4.2 times that of the raw material. This improved efficiency was attributed to the enhanced accessibility of cellulose, the weakened surface area of lignin, the declined hydrophobicity, and the decreased crystallinity of cellulose. Several compelling linear correlations were fitted between enzymatic hydrolysis and these alterations of physicochemical features, comprehensively understanding enzymatic saccharification of Betaine:LA-pretreated SCB.

Ultrasound-Assisted Extraction of Taro Leaf Antioxidants Using Natural Deep Eutectic Solvents: An Eco-Friendly Strategy for the Valorization of Crop Residues

Colocasia esculenta L. leaves are considered a by-product of taro cultivation and are discarded as environmental waste, despite their valuable phenolic composition. Their valorization to obtain value-added substances for medicinal, food, and cosmetic applications is the aim of the current work. An ultrasound-assisted extraction was developed for the environmentally friendly and sustainable isolation of taro leaf antioxidants using natural deep eutectic solvents (NaDESs). Among the utilized solvents, the NaDES based on betaine and ethylene glycol provided the best extraction efficiencies in terms of polyphenolic content and antioxidant activity. Multi-response optimization suggested a solvent-to-solid ratio of 10 mL g-1, a processing time of 60 min, an extraction temperature of 60 °C, and a water content of 33.8% (w/w) as optimal extraction parameters. Leaf extract obtained under these optimum operational parameters demonstrated a strong radical scavenging activity against 2,2-diphenyl-1-picrylhydrazyl (65.80 ± 0.87%), a high ferric reducing antioxidant power (126.62 ± 1.92 μmol TE g-1 sample), and significant protection against oxidative stress-induced DNA damage. The chromatographic characterization of the optimum extract revealed its richness in flavonoids (flavones and flavonols). The outcomes of the present study suggest that the proposed method could serve as a highly efficient and green alternative for the recovery of polyphenols from agricultural wastes.

Optimization and kinetics modeling of phenolics extraction from coffee silverskin in deep eutectic solvent using ultrasound-assisted extraction

This research investigates the effect of extraction parameters on total phenolic content (TPC) and the antioxidant capacity of coffee silverskin (CS) extract using ultrasound-assisted extraction (UAE) in deep eutectic solvent (DES). The optimization was carried out in two stages: (i) the optimization of the UAE condition with the highest TPC; and (ii) a four-factor Box-Behnken design (BBD) to optimize the UAE condition with the optimal TPC; 2,2 diphenyl-1-picrylhydrazyl (DPPH) radical scavenging capacity; and ferric reducing antioxidant power (FRAP). The results showed that the optimal UAE condition with the highest TPC was 150-250 μm CS particle size; 1,6-hexanediol as hydrogen bond donor (HBD); 1:7 HBA:HBD molar ratio; and 30% (w/w) water content, given choline chloride (ChCl) as hydrogen bond acceptor (HBA), 30 min extraction time and 30 ° C extraction temperature. The BBD-based optimal UAE condition was 30% w/w water content, 45 mL/g liquid/solid ratio, 90 min extraction time and 85 ° C extraction temperature, given the CS particle size of 150-250 μm and the HBA:HBD molar ratio of 1 (ChCl): 7 (1,6 hexanediol), achieving 19.19 ± 0.20 mg GAE/g CS for TPC, 24.06 ± 1.77 mg TE/g CS for DPPH radical scavenging capacity, and 59.13 ± 4.55 mg Fe (II)/g CS for FRAP. The experimental results were in good agreement with the BBD-based predicted results (22.40 mg GAE/g CS for TPC, 24.09 mg TE/g CS for DPPH, and 59.43 mg Fe(II)/g CS for FRAP). The two-site kinetics model best fitted the experimental data, with R2 of 0.991-0.999.

Artificial intelligence for waste management in smart cities: a review

The rising amount of waste generated worldwide is inducing issues of pollution, waste management, and recycling, calling for new strategies to improve the waste ecosystem, such as the use of artificial intelligence. Here, we review the application of artificial intelligence in waste-to-energy, smart bins, waste-sorting robots, waste generation models, waste monitoring and tracking, plastic pyrolysis, distinguishing fossil and modern materials, logistics, disposal, illegal dumping, resource recovery, smart cities, process efficiency, cost savings, and improving public health. Using artificial intelligence in waste logistics can reduce transportation distance by up to 36.8%, cost savings by up to 13.35%, and time savings by up to 28.22%. Artificial intelligence allows for identifying and sorting waste with an accuracy ranging from 72.8 to 99.95%. Artificial intelligence combined with chemical analysis improves waste pyrolysis, carbon emission estimation, and energy conversion. We also explain how efficiency can be increased and costs can be reduced by artificial intelligence in waste management systems for smart cities.

Physical-chemical and ecotoxic evaluation of different deep eutectic solvents for green analytical applications

The search for new analytical methods is a latent reality in the so-called green analytical chemistry area, which aims at correlating analytical demands to environmental issues. Among the approaches used, it is possible to highlight green solvents as substitutes to the dangerous and conventional organic solvents as the most prominent alternative for this purpose. In the last few years, the amount of research focused on the usage of deep eutectic solvents (DESs) has been growing as an alternative to these issues. Thus, this work aimed to investigate the main physical-chemical and ecotoxical properties of seven different DESs. The results showed that DESs' evaluated properties are influenced by the chemical structure of their precursors, which may regulate DESs' viscosity, superficial tension, and antagonistic action against vegetable tissues and microbial cells. The constatations pointed here introduce a new perspective about the conscious usage of DESs on a green analytical point of view.

Adsorption of amphetamine on deep eutectic solvents functionalized graphene oxide/metal-organic framework nanocomposite: Elucidation of hydrogen bonding and DFT studies

The efficient and selective removal of amphetamine (AMP) from water bodies is significant for environmental remediation. In this study, a novel strategy for screening deep eutectic solvent (DES) functional monomers was proposed based on density functional theory (DFT) calculations. Using magnetic GO/ZIF-67 (ZMG) as substrates, three DES-functionalized adsorbents (ZMG-BA, ZMG-FA, and ZMG-PA) were successfully synthesized. The isothermal results showed that the DES-functionalized materials introduced more adsorption sites and mainly contributed to the formation of hydrogen bonds. The order of the maximum adsorption capacity (Q_m) was as follows: ZMG-BA (732.110 μg⋅g^-1) > ZMG-FA (636.518 μg⋅g^-1) > ZMG-PA (564.618 μg⋅g^-1) > ZMG (489.913 μg⋅g^-1). The adsorption rate of AMP on ZMG-BA was the highest (98.1%) at pH 11, which could be explained by the less protonation of -NH₂ from AMP being more favorable for forming hydrogen bonds with the -COOH of ZMG-BA. The strongest affinity of the -COOH of ZMG-BA for AMP was reflected in the most hydrogen bonds and the shortest bond length. The hydrogen bonding adsorption mechanism was fully explained by experimental characterization (FT-IR, XPS) and DFT calculations. Frontier Molecular Orbital (FMO) calculations showed that ZMG-BA had the lowest HOMO-LUMO energy gap (E_gap), the highest chemical activity and the best adsorption capability. The experimental results agreed with the results of theoretical calculations, proving the validity of the functional monomer screening method. This research offered fresh suggestions for the functionalized modification of carbon nanomaterials to achieve effective and selective adsorption for psychoactive substances.

The Role of Water Content of Deep Eutectic Solvent Ethaline in the Anodic Process of Gold Electrode

Traditional coupling of ligands for gold wet etching makes large-scale applications problematic. Deep eutectic solvents (DESs) are a new class of environment-friendly solvents, which could possibly overcome the shortcomings. In this work, the effect of water content on the Au anodic process in DES ethaline was investigated by combining linear sweep voltammetry (LSV) and electrochemical impedance spectroscopy (EIS). Meanwhile, we employed atomic force microscopy (AFM) to image the evolution of the surface morphology of the Au electrode during its dissolution and passivation process. The obtained AFM data help to explain the observations about the effect of water content on the Au anodic process from the microscopic perspective. High water contents make the occurrence of anodic dissolution of gold at higher potential, but enhances the rate of the electron transfer and gold dissolution. AFM results reveal the occurrence of massive exfoliation, which confirms that the gold dissolution reaction is more violent in ethaline with higher water contents. In addition, AFM results illustrate that the passive film and its average roughness could be tailored by changing the water content of ethaline.

Detoxification of comfrey (Symphytum officinale L.) extract using natural deep eutectic solvent (NADES) and evaluation of its anti-inflammatory, antioxidant, and hepatoprotective properties

Comfrey (Symphytum officinale L.) contains rosmarinic acid which has different pharmacological activities, such as antioxidant and anti-inflammatory activities. However, the medicinal use of comfrey is limited by the hepatotoxic effect of lycopsamine in comfrey, which overshadows the health benefits of rosmarinic acid. Natural deep eutectic solvents (NADES) have a wide range of extraction properties, that provides a new approach to the detoxification of comfrey. In the present study, betaine-based and choline chloride-based NADES were screened for selective extraction of rosmarinic acid over lycopsamine. Ultrasonication was used in conjunction with NADES extraction. The chemical profile of the NADES extracts on antioxidant, anti-inflammatory and hepatotoxic activities were investigated using some chemical reagents. Betaine-urea (1:2 molar ratio, 50% water) obtained the highest content of rosmarinic acid and a low level of lycopsamine (1.934 and 0.018 mg/g, respectively). Betaine-urea was also shown to be more effective to extract rosmarinic acid compared to methanol-UAE under the same conditions, which gave lower rosmarinic acid and higher lycopsamine levels (0.007 and 0.031 mg/g, respectively). Betaine-urea extracts showed higher antioxidant and anti-inflammatory properties as compared with other NADES extracts, however, had lower hepatotoxic profile. This study recommends the use of betaine-urea to detroxify comfrey to open wider opportunities for the development of comfrey for medicinal use.

Deep Eutectic Solvents for Biotechnology Applications

Deep eutectic solvents (DESs) are an alternative to traditional organic solvents and ionic liquids and meet the requirements of "green" chemistry. They are easy to prepare using low-cost constituents, are non-toxic and biodegradable. The review analyzes literature on the use of DES in various fields of biotechnology, provides data on the types of DESs, methods for their preparation, and properties. The main areas of using DESs in biotechnology include extraction of physiologically active substances from natural resources, pretreatment of lignocellulosic biomass to improve enzymatic hydrolysis of cellulose, production of bioplastics, as well as a reaction medium for biocatalytic reactions. The aim of this review is to summarize available information on the use of new solvents for biotechnological purposes.

Experimental and theoretical study of the physicochemical properties of the novel imidazole-based eutectic solvent

Novel solvents and their applications are experiencing an increasing interest by the scientific community. Imidazole has been utilized as a major component in many successful ionic liquids. However, very limited studies were reported for using it as a hydrogen bond acceptor in the synthesis of eutectic solvents. In this work, a novel eutectic solvent composed of Imidazole and Monoethanolamine (MEA) is synthesized at different molar ratios. The basic physicochemical properties such as melting point, density, viscosity, and refractive index were measured at different temperatures and modeled as a function of molar composition and temperature. FTIR and ¹H NMR analyses were conducted and, the nature and strength of the molecular interaction between the two solvent molecules were investigated by conducting combined molecular dynamics (MD) simulations and density functional theory (DFT) calculations. The study revealed the electrostatic H-bonding nature of interaction with strength related to their bond distances. The binding energy between the two DES ingredients is proportional to the amount of MEA in the DES due to increasing the H-bonding interactions between Imidazole and MEA molecules. These findings suggest that DES might be used in a variety of chemical and industrial applications.

Critical Assessment of the Sustainability of Deep Eutectic Solvents: A Case Study on Six Choline Chloride-Based Mixtures

An outline of the advantages, in terms of sustainability, of Deep Eutectic Solvents (DESs) is provided, by analyzing some of the most popular DESs, obtained by the combination of choline chloride, as a hydrogen bond acceptor, and six hydrogen bond donors. The analysis is articulated into four main issues related to sustainability, which are recurrently mentioned in the literature, but are often taken for granted without any further critical elaboration, as the prominent green features of DESs: their low toxicity, good biodegradability, renewable sourcing, and low cost. This contribution is intended to provide a more tangible, evidence-based evaluation of the actual green credentials of the considered DESs, to reinforce or question their supposed sustainability, also in mutual comparison with one another.

Glycerol and Natural Deep Eutectic Solvents Extraction for Preparation of Luteolin-Rich Jasione montana Extracts with Cosmeceutical Activity

Jasione montana is a plant from the family Campanulaceae rich in phenols with health-beneficial properties such as luteolin (LUT) derivatives. In this work, a glycerol-based ultrasound-assisted extraction method was developed and optimized for in total phenol (TP) and LUT content, as well as antiradical activity (RSA). The best conditions (glycerol content, temperature, plant material weight, and ultrasonication power) for the preparation of J. montana extracts richest in TP (OPT-TP), LUT (OPT-LUT), and having the best RSA (OPT-RSA) were determined. Furthermore, numerous natural deep eutectic solvents (NADES), containing proline, glycerol, betaine, urea, and glucose were prepared and used for the extraction of J. montana. Contents of TP, LUT, and RSA in the prepared extracts were established. Antioxidant and cosmeceutical activity of the prepared extracts was tested. The OPT-TP, OPT-LUT, and OPT-RSA, as well as the most efficient NADES-based extract, PG-50-TP, were excellent antioxidants and Fe²⁺ ion chelators. In addition, they were potent inhibitors of collagenase and hyaluronidase, as well as good significant anti-elastase and -lipoxygenase activity. The observed antioxidant- and enzyme-inhibiting activity of J. montana extracts prepared using environmentally friendly methods and non-toxic solvents makes them promising ingredients of cosmeceutical products.

Lignin-Derived Oil Palm Biomass Using Deep Eutectic Solvent

Deep Eutectic Solvent (DES) are eutectic mixes of hydrogen bond acceptors (HBA) and donors (HBD) with melting points significantly lower than their constituents. Choline chloride (ChCl) and glycerol were chosen as HBA and HBD because they are simple to prepare, have low toxicity, are biodegradable, and are environmentally friendly. As a result, the study aims to determine the feasibility of extracting lignin from oil palm fronds (OPF) and empty fruit bunches (EFB) using DES. The molar ratios of DESs were investigated to determine their effect on OPF solubility and lignin yield. The reaction is carried out at a solid loading ratio of 1:10, 150°C, and 6 hours. Because the DES medium induces homogeneous swelling and breakdown of small fibre fragments but not dissolution, both OPF and EFB are insoluble in DES. Small fragment disintegration suggests rapid dissolution, which will be easily dissolved in the DESs. The lignin yield and solubility of EFB and OPF in DESs are significantly reduced when the molar concentration of glycerol is increased. The highest lignin yields, 27.6% (EFB) and 16.1% (OPF) were obtained with a ChCl/glycerol molar ratio of 1:3. The comparatively low lignin yield achieved for both OPF and EFB is ascribed to the poor hydrogen bonding between the chloride ion and the hydroxyl group of the DES due to the low acidity of the DES. Despite this, lignin is extracted successfully due to the presence of chloride ions in ChCl, which target β-O-4 bonds and successfully cleave the ether bonds present in the lignin-carbohydrate linkage.

A review on potential of green solvents in hydrothermal liquefaction (HTL) of lignin

One of the greatest challenges in biorefinery is to reduce biomass' recalcitrance and enable valorization of lignin into higher value compounds. Likewise, green solvents and hydrothermal liquefaction (HTL) with feasible economic viability, functionality, and environmental sustainability have been widely introduced in extraction and conversion of lignin. This review starts with the underscore of disadvantages and limitations of conventional pretreatment approaches and role of green solvents in lignin extraction. Subsequently, the effect of process parameters along with the reaction mechanisms and kinetics on conversion of lignin through HTL were comprehensively reviewed. The limitations of green solvents in extraction and HTL of lignin from biomass were discussed based on the current advancements of the field and future research scopes were also proposed. More details info on HTL of biomass derived lignin which avoid the energy-intensive drying procedures are crucial for the accelerated development and deployment of the advanced lignin biorefinery.

Deep Eutectic Solvent Pretreatment of Water Hyacinth for Improved Holocellulosic Saccharification and Fermentative Co-Production of Xylitol and Lipids Using Rhodosporidium toruloides NCIM 3547

In this study, delignification of water hyacinth (WH) using a mild ionic liquid-like chemical deep eutectic solvent (DES) synthesized using choline chloride and urea was conducted and the process parameters were optimized by Box–Behnken design (BBD)-based response surface methodology (RSM). From the results, a delignification of 64.32 ± 4.08% (w/w) was obtained under 1:12.5 (biomass:DES ratio), 4.63 h (time) and 87 °C (temperature). Further, a dilute sulphuric acid (2%, v/v) hydrolysis was carried out to destabilize the hemicellulose that resulted in 23.7 ± 0.50 g/L of xylose. Fermentation of the obtained xylose was carried out using a red oleaginous yeast, Rhodosporidium toruloides NCIM 3547, with free and Ca2+-alginate-immobilized cells for xylitol production under microaerophilic conditions and obtained yields of 4.73 ± 0.40 g/L (168 h) and 9.18 ± 0.10 g/L (packed bed reactor with a retention time of 18 h), respectively. Further, when the same fermentation was performed under aerobic conditions about 40.93 ± 0.73% lipid accumulation was observed with free cells. For saccharification, Aspergillus-niger-derived cellulase was used and this resulted in a yield of 27.45 ± 0.04 g/L of glucose. The glucose-enriched hydrolysate was supplemented for fermentation under nitrogen starved conditions from which 46.81 ± 2.60% (w/w) lipid content was obtained.

Onion waste based-biorefinery for sustainable generation of value-added products

Waste derived from the onion processing sector can be harnessed for the production of organic acids, polyphenols, polysachharides, biofuels and pigments. To sustainably utilize onion processing residues, different biorefinery strategies such as enzymatic hydrolysis, fermentation and hydrothermal carbonization have been widely investigated. This review discusses the recent advances in the biorefinery approaches used for valorization of onion processing waste followed by the production of different value-added products from diverse classes of onion waste. The review also highlights the current challenges faced by the bioprocessing sector for the utilization of onion processing waste and perspectives to tackle them.

Betaine-Based Deep Eutectic Solvent as a New Media for Laccase-Catalyzed Template-Guided Polymerization/Copolymerization of Aniline and 3-Aminobenzoic Acid

Deep eutectic solvents (DESs) can compensate for some of the major drawbacks of traditional organic solvents and ionic liquids and meet all requirements of green chemistry. However, the potential of their use as a medium for biocatalytic reactions has not been adequately studied. In this work we used the DES betaine-glycerol with a molar ratio of 1:2 as co-solvent for enzymatic template-guided polymerization/copolymerization of aniline (ANI) and 3-aminobenzoic acid (3ABA). The laccase from the basidial fungus Trametes hirsuta and air oxygen served as catalyst and oxidant, respectively. Sodium polystyrene sulfonate (PSS) was used as template. Interpolyelectrolyte complexes of homopolymers polyaniline (PANI) and poly(3-aminobenzoic acid) (P3ABA) and copolymer poly(aniline-co-3-aminobenzoic acid) (P(ANI-3ABA)) were prepared and their physico-chemical properties were studied by UV-Vis and FTIR spectroscopy and cyclic voltammetry. According to the results obtained by atomic force microscopy, PANI/PSS had a granular shape, P(ANI-3ABA)/PSS had a spherical shape and P3ABA/PSS had a spindle-like shape. The copolymer showed a greater antimicrobial activity against Escherichia coli and Staphylcocus aureus as compared with the homopolymers. The minimal inhibitory concentration of the P(ANI-3ABA)/PSS against the gram-positive bacterium S. aureus was 0.125 mg mL⁻¹.

Natural deep eutectic solvents in phytonutrient extraction and other applications

Natural deep eutectic solvents (NaDESs) are considered a new type of green solvent with attractive application prospects in many fields because of their simple preparation, low cost, environmental friendliness, low volatility, high solvency capacity, designable structure, and easy biodegradability. Due to their biocompatibility, they are safe to use and are particularly suitable for natural product applications. In recent years, NaDESs have been used to extract phytonutrients (e.g., flavonoids, saponins, polysaccharides, alkaloids, quinones, phenolic acids, volatile oils, etc.) to improve their solubility, stability, and bioavailability. This review is intended to summarize and discuss recent progress in the field of natural products related to materials and preparation methods, physicochemical properties, enhancing extraction and separation, increasing solubility, improving stability and bioavailability, facilitating oral absorption of phytonutrients, and finally, highlighting the challenge for future work.

Recent Advancements and Challenges in Lignin Valorization: Green Routes towards Sustainable Bioproducts

The aromatic hetero-polymer lignin is industrially processed in the paper/pulp and lignocellulose biorefinery, acting as a major energy source. It has been proven to be a natural resource for useful bioproducts; however, its depolymerization and conversion into high-value-added chemicals is the major challenge due to the complicated structure and heterogeneity. Conversely, the various pre-treatments techniques and valorization strategies offers a potential solution for developing a biomass-based biorefinery. Thus, the current review focus on the new isolation techniques for lignin, various pre-treatment approaches and biocatalytic methods for the synthesis of sustainable value-added products. Meanwhile, the challenges and prospective for the green synthesis of various biomolecules via utilizing the complicated hetero-polymer lignin are also discussed.

A neoteric approach for the complete valorization of Typha angustifolia leaf biomass: A drive towards environmental sustainability

Exploring new biomass resources and developing a sustainable process for holistic utilization has become crucial due to the high demand for bio-based chemicals as alternatives to petrochemicals. Herein, we describe a novel approach to valorize the Typha angustifolia leaves, underutilized biomass into cellulose, hemicellulose and lignin nanoparticles. The process was framed in a sequence to isolate hemicellulose in the first step due to its highly reactive nature and then separate cellulose and lignin. Among the various natural deep eutectic solvents used in screening experiments, LA/ChCl (2:1) was chosen for hemicellulose solubilization and a dissolution yield of 95.97 ± 1.8% was obtained in 30 min at 240 W microwave power. Then the residual solid was delignified using NaOCl₂ at 180 W microwave power and a yield of 97 ± 0.75% was obtained in 15 min. Dissolved hemicellulose and lignin were precipitated using anti-solvents. The proposed approach achieved a recovery yield of 95.5 ± 1.2% cellulose, 91.9 ± 2.6% hemicellulose and 89.5 ± 1.6% lignin. Subsequently, the isolated particles were converted into nanoparticles by intense ultrasonication. Spherical shaped nanocellulose, nanohemicellulose and nanolignin were obtained with an average size of 76 ± 7 nm, 86 ± 9 nm, and 64 ± 5 nm, respectively. The produced nanocellulose had a crystallinity of 77.36% with the thermal stability of 265 °C. Nanohemicellulose and nanolignin were found to be semicrystalline with thermal stability up to 245 °C and 275 °C, respectively. The characterization results of the nanoparticles isolated from Typha angustifolia leaves are indicative of their wide range of biomedical and material science applications. This research could open a window for complete utilization of biomass in biorefinery and sustainable management of an invasive plant Typha angustifolia.

Lactic Acid-Based Natural Deep Eutectic Solvents to Extract Bioactives from Marine By-Products

Natural deep eutectic solvents (NaDES) were used to extract bioactive compounds from marine by-products: codfish bones, mussel meat, and tuna vitreous humor. NaDES were prepared using natural compounds, including lactic acid (Lac), fructose (Fru), and urea (Ur), and were characterized to define their physicochemical properties, including the viscosity, density, surface tension, and refractive index. FTIR and NMR analysis confirmed the presence of intermolecular hydrogen bonding in NaDES. The extracts obtained using these NaDES were characterized to define their composition. Results demonstrated that the extract’s composition differed highly, depending not only on the DES used, but also on the structure and composition of the raw material. Proteins and lipids were mainly present in extracts obtained from mussels, while ash content was highest in the extracts obtained from codfish bones. The biocompatibility of NaDES and the soluble fractions (SF) of the raw materials in NaDES was evaluated, and it was possible to conclude that the soluble ingredients obtained from the raw materials improved the biocompatibility of NaDES.