First in Human Clinical Feasibility Study of Endovascular Navigation with Fiber Optic RealShape (FORS) Technology

Editor's Choice - Radiation Dose Reduction During Contralateral Limb Cannulation Using Fiber Optic RealShape Technology in Endovascular Aneurysm Repair

OBJECTIVE

The increasing number of endovascular procedures has resulted in an increasing radiation burden, particularly for the treatment team. Fiber Optic RealShape (FORS) technology uses laser light instead of fluoroscopy to visualise the endovascular guidewire and catheters. These devices can be used during the navigational part of procedures, such as cannulation of the contralateral limb (CL) in endovascular aneurysm repair (EVAR). The aim of this study was to describe the effect of using FORS on radiation dose during CL cannulation in standard EVAR.

METHODS

This was a non-randomised, retrospective comparison study of prospectively collected, single centre data from FORS guided EVAR compared with a conventional fluoroscopy only guided EVAR cohort. A total of 27 FORS guided cases were matched 1:1 based on sex, age, and body mass index (BMI) with 27 regular (fluoroscopy only) EVARs. This study primarily focused on (1) technical success of FORS and (2) navigation time and radiation dose (cumulative air kerma [CAK], air kerma area product [KAP], and fluoroscopy time [FT]) during cannulation of the CL. In addition, overall procedure time and radiation dose of the complete EVAR procedure were studied.

RESULTS

In 22 (81%) of the 27 FORS guided cases the CL was successfully cannulated using FORS. All radiation dose parameters were significantly lower in the FORS group (CAK, p < .001; KAP, p = .009; and FT, p < .001) for an equal navigation time (p = .95). No significant differences were found when comparing outcomes of the complete procedure.

CONCLUSION

Use of FORS technology significantly reduces radiation doses during cannulation of the CL in standard EVAR.

Sensorized Endovascular Technologies: Additional Data to Enhance Decision-Making

BACKGROUND

Current endovascular procedures rely mostly on anatomic information, guided by fluoroscopy, to perform interventions (i.e. angioplasty, stent placement, coils). However, the structural parameters provided by these imaging technologies do not provide any physiological data on either the disease state or efficacy of intervention. Additional endovascular tools are needed to collect physiologic and other both anatomic and nonanatomic data to further individualize endovascular interventions with the ultimate goal of improving patient outcomes. This review details the current state of the art for these sensorized endovascular technologies and details systems under development with the aim of identifying gaps and new directions. The objective of this review was to survey the Vascular Surgery literature, engineering literature, and commercially available products to determine what exists in terms of sensor-enabled endovascular devices and where gaps and opportunities exist for further sensor integration.

METHODS

Search terms were entered into search engines such as Google and Google Scholar to identify endovascular devices containing sensors. A variety of terms were used including directly search for items such as "sensor-enabled endovascular devices" and then also completing more refined searches bases on areas of interest (i.e. fractional flow reserve, navigation, retrograde endovascular balloon occlusion of the aorta, etc.). For the most part, systems were included where the sensor was mounted directly onto the catheter and implantable sensors such as those that have been investigated for use with stents have been excluded.

RESULTS

The authors were able to identify a body of literature in the area of endovascular devices that contain sensors to measure physiologic information. However, areas where additional sensing capabilities may be useful were identified.

CONCLUSIONS

Several different types of sensors and sensing systems were identified that have been integrated with endovascular catheters. Although a great deal of work has been done in this field, there are additional useful data that could be obtained from additional novel sensing technologies. Furthermore, significant effort needs to be allocated to carefully studying how these new technologies can be employed to actually improve patient outcomes.

Editor's Choice -- European Society for Vascular Surgery (ESVS) 2024 Clinical Practice Guidelines on the Management of Abdominal Aorto-Iliac Artery Aneurysms

OBJECTIVE

The European Society for Vascular Surgery (ESVS) has developed clinical practice guidelines for the care of patients with aneurysms of the abdominal aorta and iliac arteries in succession to the 2011 and 2019 versions, with the aim of assisting physicians and patients in selecting the best management strategy.

METHODS

The guideline is based on scientific evidence completed with expert opinion on the matter. By summarising and evaluating the best available evidence, recommendations for the evaluation and treatment of patients have been formulated. The recommendations are graded according to a modified European Society of Cardiology grading system, where the strength (class) of each recommendation is graded from I to III and the letters A to C mark the level of evidence.

RESULTS

A total of 160 recommendations have been issued on the following topics: Service standards, including surgical volume and training; Epidemiology, diagnosis, and screening; Management of patients with small abdominal aortic aneurysm (AAA), including surveillance, cardiovascular risk reduction, and indication for repair; Elective AAA repair, including operative risk assessment, open and endovascular repair, and early complications; Ruptured and symptomatic AAA, including peri-operative management, such as permissive hypotension and use of aortic occlusion balloon, open and endovascular repair, and early complications, such as abdominal compartment syndrome and colonic ischaemia; Long term outcome and follow up after AAA repair, including graft infection, endoleaks and follow up routines; Management of complex AAA, including open and endovascular repair; Management of iliac artery aneurysm, including indication for repair and open and endovascular repair; and Miscellaneous aortic problems, including mycotic, inflammatory, and saccular aortic aneurysm. In addition, Shared decision making is being addressed, with supporting information for patients, and Unresolved issues are discussed.

CONCLUSION

The ESVS Clinical Practice Guidelines provide the most comprehensive, up to date, and unbiased advice to clinicians and patients on the management of abdominal aorto-iliac artery aneurysms.

Patients' Radiation Exposure During Endovascular Abdominal Aortic Aneurysm Repair

BACKGROUND

To investigate associations between patient characteristics, intraprocedural complexity factors, and radiation exposure to patients during endovascular abdominal aortic aneurysm repair (EVAR).

METHODS

Elective standard EVAR procedures between January 2015 and December 2020 were retrospectively analyzed. Patient characteristics and intraprocedural data (i.e., type of device, endograft configuration, additional procedures, and contralateral gate cannulation time [CGCT]) were collected. Dose area product (DAP) and fluoroscopy time were considered as measurements of radiation exposure. Furthermore, effective dose (ED) and doses to internal organs were calculated using PCXMC 2.0 software. Descriptive statistics, univariable, and multivariable linear regression were applied to investigate predictors of increased radiation exposure.

RESULTS

The 99 patients were mostly male (90.9%) with a mean age of 74 ± 7 years. EVAR indications were most frequently abdominal aortic aneurysm (93.9%), penetrating aortic ulceration (2.0%), focal dissection (2.0%), or subacute rupture of infrarenal abdominal aortic aneurysm (2.0%). Median fluoroscopy time was 19.6 minutes (interquartile range [IQR], 14.1-29.4) and median DAP was 86,311 mGy cm2 (IQR, 60,160-130,385). Median ED was 23.2 mSv (IQR, 17.0-34.8) for 93 patients (93.9%). DAP and ED were positively correlated with body mass index (BMI) and CGCT. Kidneys, small intestine, active bone marrow, colon, and stomach were the organs that received the highest equivalent doses during EVAR. Higher DAP and ED values were observed using the Excluder endograft, other bi- and tri-modular endografts, and EVAR with ≥2 additional procedures. Multivariable linear regression analysis revealed that BMI, ≥2 additional procedures during EVAR, and CGCT were independent positive predictors of DAP and ED levels after accounting for endograft type.

CONCLUSIONS

Patient-related and procedure-related factors such as BMI, ≥2 additional procedures during EVAR, and CGCT resulted predictors of radiation exposure for patients undergoing EVAR, as quantified by higher DAP and ED levels. The main intraprocedural factor that increased radiation exposure was CGCT. These data can be of importance for better managing radiation exposure during EVAR.

Artificial Intelligence, Computational Simulations, and Extended Reality in Cardiovascular Interventions

Artificial intelligence, computational simulations, and extended reality, among other 21st century computational technologies, are changing the health care system. To collectively highlight the most recent advances and benefits of artificial intelligence, computational simulations, and extended reality in cardiovascular therapies, we coined the abbreviation AISER. The review particularly focuses on the following applications of AISER: 1) preprocedural planning and clinical decision making; 2) virtual clinical trials, and cardiovascular device research, development, and regulatory approval; and 3) education and training of interventional health care professionals and medical technology innovators. We also discuss the obstacles and constraints associated with the application of AISER technologies, as well as the proposed solutions. Interventional health care professionals, computer scientists, biomedical engineers, experts in bioinformatics and visualization, the device industry, ethics committees, and regulatory agencies are expected to streamline the use of AISER technologies in cardiovascular interventions and medicine in general.

A Novel Catheter Shape-Sensing Method Based on Deep Learning with a Multi-Core Optical Fiber

In this paper, we propose a novel shape-sensing method based on deep learning with a multi-core optical fiber for the accurate shape-sensing of catheters and guidewires. Firstly, we designed a catheter with embedded multi-core fiber containing three sensing outer cores and one temperature compensation middle core. Then, we analyzed the relationship between the central wavelength shift, the curvature of the multi-core Fiber Bragg Grating (FBG), and temperature compensation methods to establish a Particle Swarm Optimization (PSO) BP neural network-based catheter shape sensing method. Finally, experiments were conducted in both constant and variable temperature environments to validate the method. The average and maximum distance errors of the PSO-BP neural network were 0.57 and 1.33 mm, respectively, under constant temperature conditions, and 0.36 and 0.96 mm, respectively, under variable temperature conditions. This well-sensed catheter shape demonstrates the effectiveness of the shape-sensing method proposed in this paper and its potential applications in real surgical catheters and guidewire.

Fiber Optic RealShape imaging using upper extremity and transfemoral access for fenestrated-branched endovascular aortic aneurysm repair

We report our initial experience using Fiber Optic RealShape (FORS), an innovative real-time three-dimensional visualization technology that uses light instead of radiation, to achieve upper extremity (UE) access during fenestrated/branched endovascular aortic aneurysm repair (FBEVAR). An 89-year-old male patient with a type III thoracoabdominal aortic aneurysm, unfit for open aortic repair, underwent FBEVAR. Dual fluoroscopy, intravascular ultrasound, and three-dimensional fusion overlay were used, in addition to FORS. All target artery catheterizations were successfully accomplished using FORS, from UE access, without radiation. Our experience demonstrates that FBEVAR with FORS using UE access can be used for target artery catheterization without radiation.

3D Visualisation of Navigation Catheters for Endovascular Procedures Using a 3D Hub and Fiber Optic RealShape Technology: Phantom Study Results

Objective

Fiber Optic RealShape (FORS) is a new technology that visualises the full three dimensional (3D) shape of guidewires using an optical fibre embedded in the device. Co-registering FORS guidewires with anatomical images, such as a digital subtraction angiography (DSA), provides anatomical context for navigating these devices during endovascular procedures. The objective of this study was to demonstrate the feasibility and usability of visualising compatible conventional navigation catheters, together with the FORS guidewire, in phantom with a new 3D Hub technology and to understand potential clinical benefits.

Methods

The accuracy of localising the 3D Hub and catheter in relation to the FORS guidewire, was evaluated using a translation stage test setup and a retrospective analysis of prior clinical data. Catheter visualisation accuracy and navigation success was assessed in a phantom study where 15 interventionists navigated devices to three pre-defined targets in an abdominal aortic phantom using an Xray or computed tomography angiography (CTA) roadmap. Additionally, the interventionists were surveyed about the usability and potential benefits of the 3D Hub.

Results

The location of the 3D Hub and catheter along the FORS guidewire was detected correctly 96.59% of the time. During the phantom study, all 15 interventionists successfully reached the target locations 100% of the time and the error in catheter visualisation was 0.69 mm. The interventionists agreed or strongly agreed that the 3D Hub was easy to use and the greatest potential clinical benefit over FORS is in offering interventionists choice over which catheter they used.

Conclusion

This set of studies has shown that FORS guided catheter visualisation, enabled by a 3D Hub, is accurate and easy to use in a phantom setting. Further evaluation is needed to understand the benefits and limitations of the 3D Hub technology during endovascular procedures.

Initial single-center experience using Fiber Optic RealShape guidance in complex endovascular aortic repair

OBJECTIVE

In the present study, we have described the technical success using Fiber Optic RealShape (FORS) endovascular guidance and its effects on the overall procedural time and radiation usage during complex endovascular aortic repair (EVAR).

METHODS

Fenestrated and branched EVARs performed at a single center from 2017 to 2022 were prospectively studied. FORS-guided procedures were matched retrospectively 1:3 to non-FORS-guided procedures by the incorporated target arteries and body mass index. Technical success was defined as successful target vessel cannulation using FORS for the entirety of navigation (wire insertion to exchange for a stiff wire). The predictors of technical success were evaluated via logistic regression. The procedural times and radiation doses were compared between the matched cohorts using the Wilcoxon rank sum test.

RESULTS

A total of 21 FORS-guided procedures were matched to 61 non-FORS-guided procedures. A total of 95 FORS cannulations were attempted (87 for the visceral target artery and 8 for the bifurcate gate). Technical success was achieved in 81 cannulations (85%); 15 (16%) were completed without the use of live fluoroscopy. The univariate predictors of FORS technical success included <50% target artery stenosis, <50% target artery calcification, and the target vessel attempted (P < .05 for each). FORS failures were attributed to device material properties in six cases, device failure in two cases, and the wire/catheter combination in six. The use of FORS guidance was associated with shorter median procedural and fluoroscopy times and a lower dose area product and air kerma (P ≤ .0001 for each).

CONCLUSIONS

The results from our initial experience with FORS during complex EVAR, including our learning curve, has shown promise, with acceptable technical success and reductions in procedural times and radiation usage.

Fiber Optic RealShape (FORS) Technology for Endovascular Navigation in Severe Tortuous Vessels

PURPOSE

The purpose of this study was to describe the use of a wire and catheters embedded with optical fiber (Fiber Optic RealShape [FORS]) to catheterize tortuous target vessels avoiding radiation.

TECHNIQUE

A virtual biplane vies was simulated coupling traditional x-ray system, preoperative CT scan, and FORS system to treat an isolated hypogastric aneurysm. Despite the complex anatomy, catheterization of all target vessels was possible in 12 minutes with 19 seconds of fluoroscopy time (Radiation Exposure 3.8 mGy×cm²). A minimal invasive endovascular exclusion of the aneurysm was achieved through selective coil-embolization of the iliolumbar artery and implantation of balloon expandable covered stents, thus preserving the perfusion of the superior gluteal artery.

CONCLUSION

FORS guidance allowed catheterization of a target vessel with challenging anatomy with a low radiation exposure.

Optical frequency domain reflectometry shape sensing using an extruded optical fiber triplet for intra-arterial guidance

Intra-arterial catheter guidance is instrumental to the success of minimally invasive procedures, such as percutaneous transluminal angioplasty. However, traditional device tracking methods, such as electromagnetic or infrared sensors, exhibits drawbacks such as magnetic interference or line of sight requirements. In this work, shape sensing of bends of different curvatures and lengths is demonstrated both asynchronously and in real-time using optical frequency domain reflectometry (OFDR) with a polymer extruded optical fiber triplet with enhanced backscattering properties. Simulations on digital phantoms showed that reconstruction accuracy is of the order of the interrogator's spatial resolution (millimeters) with sensing lengths of less than 1 m and a high SNR.

Endovascular navigation with Fiber Optic RealShape technology

OBJECTIVE

Fiber Optic RealShape (FORS) technology has recently been introduced as an adjunctive guidance technology that allows real-time three-dimensional visualization of dedicated endovascular devices while avoiding radiation exposure. It consists of equipment which sends pulses of light through hair-thin optical fibers that run within a dedicated hydrophilic wire and selective catheters. The purpose of the study was to report the observed benefits and limitations related to the first edition of FORS technology.

METHODS

Data were collected prospectively from the first 50 patients undergoing FORS-guided endovascular repair at a single center between February 2020 and February 2021 as part of the global multicenter FORS Learn registry. All consecutive, elective procedures with one or more navigation tasks attempted with FORS were included. Factors related to FORS navigation task success were assessed. The time required for the catheterization of each task as well as the amount of radiation exposure (fluoroscopy time, dose area product, and estimated skin dose) were collected. A per-task analysis was conducted. End points included the success rate in achieving a stable FORS-guided catheterization, catheterization time, and radiation dose during catheterization.

RESULTS

During the study period from February 2020 to February 2021, 50 patients were treated using FORS technology. Forty-five patients were treated for aortic aneurysm, 4 for iliac artery aneurysm, and 1 for splenic artery aneurysm. Overall, 201 navigation tasks were completed for these procedures and FORS was used in 186 tasks (92.5%). No FORS-related complication was recorded and a success rate of 60.2% (n = 116) was observed. Target vessel (TV) angle of 45° or greater, TV stenosis, and the renal arteries as navigation tasks (compared with celiac artery or superior mesenteric artery) were associated with a lower success rate. Catheterization of a TV through a branch more frequently required a standard catheter in combination with the FORS-enabled guidewire. Successful task catheterization using FORS guidance was associated with a shorter catheterization time 6 minutes (interquartile range, 3-11 minutes) versus 16 minutes (interquartile range, 10-24 minutes) (P < .001) and lower radiation exposure compared with unsuccessful catheterization (dose area product, 4.4 cGy/cm² vs 12.5 cGy/cm²; P < .001).

CONCLUSIONS

FORS technology was implemented successfully as a new guidance technology in a complex endovascular aortic repair program and was associated with an encouraging success rate and a high potential for radiation reduction.

Rayleigh-Based Distributed Optical Fiber Sensing

Distributed optical fiber sensing is a unique technology that offers unprecedented advantages and performance, especially in those experimental fields where requirements such as high spatial resolution, the large spatial extension of the monitored area, and the harshness of the environment limit the applicability of standard sensors. In this paper, we focus on one of the scattering mechanisms, which take place in fibers, upon which distributed sensing may rely, i.e., the Rayleigh scattering. One of the main advantages of Rayleigh scattering is its higher efficiency, which leads to higher SNR in the measurement; this enables measurements on long ranges, higher spatial resolution, and, most importantly, relatively high measurement rates. The first part of the paper describes a comprehensive theoretical model of Rayleigh scattering, accounting for both multimode propagation and double scattering. The second part reviews the main application of this class of sensors.

Temperature-dependent optical properties of some mixtures nematic liquid crystal

The presence of optical anisotropy in liquid crystals (LCs) has caused these materials to have dual refractive indices: ordinary (n_o) and extra-ordinary (n_e). Many fundamental information about LCs can be found by looking at these refractive indices. In this work, the refractive indices of four mixtures nematic liquid crystal (NLC) have been studied as a function of temperature, and the relevant functions were then calculated. Subsequently, the order parameter of mentioned LCs was determined using three methods: Vuks, Haller, and the effective geometry parameter method. It was concluded that the obtained values are not significantly different and exhibit the same temperature dependence. The obtained results were evaluated in relation to the approach utilized.

Superficial Femoral Artery Recanalization Using Fiber Optic RealShape Technology

Purpose: Report of a successful case of endovascular recanalization of an occluded superficial femoral artery (SFA) using Fiber Optic RealShape (FORS) technology. Case Report: A 79-year-old male was referred for evaluation of multiple ischemic pretibial ulcers of the right lower extremity. Computed tomography–angiography (CTA) imaging confirmed significant stenosis of the right common femoral artery (CFA) and an occlusion of the SFA from its origin to the Hunter’s canal. The patient was treated with a hybrid surgical procedure: an endarterectomy of the CFA and SFA origin was performed combined with an endovascular recanalization of the occluded SFA using FORS technology. During recanalization, the FORS guidewire slowly twisted subintimally around the occluded lumen of the SFA, maintaining the created corkscrew shape after pre-dilation with the percutaneous transluminal angioplasty (PTA) balloon and subsequent stenting. Conclusions: FORS technology can be successfully used during recanalization of an occluded SFA without the use of fluoroscopy. The corkscrew shape formed during recanalization in this case was retained during PTA balloon pre-dilation and stenting; this potentially improves hemodynamics and thereby reduces the risk of in-stent restenosis. However, expanding patient series and longer follow-up data are needed to increase the understanding of the feasibility and effectiveness of using FORS in the treatment of peripheral arterial occlusive disease.

Simultaneous interrogation of multiple cores in a shape sensor fiber with a graded index fiber micro-turnaround

A critical limitation for optical fiber sensor technology is the complexity of the interrogators used in such measurements, which has driven continued interest in enhanced optical fibers and fiber assemblies that will simplify interrogator design. In this work, we report on a novel multicore fiber shape sensor utilizing a distal graded index (GRIN) fiber micro-turnaround. We show that four offset cores of this fiber can be interrogated simultaneously with a single high performance optical frequency domain reflectometry measurement. The GRIN turnaround is 498 µm in length and reflects signal from one offset core to an opposite core with a 2 dB roundtrip attenuation. We show that the bend sensing accuracy of our single measurement system is similar to the accuracy of sequential measurements of four individual cores. We also demonstrate fiber shape reconstruction with a single measurement over 0.55 m with 80 µm spatial resolution when the fiber is wrapped around two posts.

New tools to reduce radiation exposure during aortic endovascular procedures

INTRODUCTION

The evolution of endovascular surgery over the past 30 years has made it possible to treat increasingly complex vascular pathologies with an endovascular method. Although this generally speeds up the patient's recovery, the risks of health problems caused by long-term exposure to radioactive radiation increase. This warrants the demand for radiation-reducing tools to reduce radiation exposure during these procedures.

AREAS COVERED

For this systematic review Pubmed, Embase and Cochrane library databases were searched on 28 December 2021 to provide an overview of tools that are currently used or have the potential to contribute to reducing radiation exposure during endovascular aortic procedures. In addition, an overview is presented of radiation characteristics of clinical studies comparing a (potential) radiation-reducing device with conventional fluoroscopy use.

EXPERT OPINION

Radiation-reducing instruments such as fiber optic shape sensing or electromagnetic tracking devices offer the possibility to further reduce or even eliminate the use of radiation during endovascular procedures. In an era of increasing endovascular interventional complexity and awareness of the health risks of long-term radiation exposure, the use of these technologies could have a major impact on an ongoing challenge to move toward radiation-free endovascular surgery.

Fully Ultrasound-Assisted Endovascular Aneurysm Repair (EVAR): preliminary report

BACKGROUND

Reducing fluoroscopy times and iodine contrast administration during endovascular exclusion (EVAR) of infrarenal aortic aneurysms (AAA) remains a challenge. The purpose of this study was to evaluate the preliminary results of a fully ultrasound-assisted EVAR without iodine contrast administration.

METHODS

Twentyseven consecutive patients, underwent an elective IVUS-assisted EVAR with final CEUS control of correct aneurysm exclusion. In no case intraprocedural injection of iodine contrast medium was performed. The primary study's endpoints were the overall duration of the procedure, duration of fluoroscopy, cumulative radiation dose, the length of intraoperative CEUS control and the comparison of findings between intraoperative CEUS and CT-scan at one month.

RESULTS

Mean duration of the procedure was 130 ± 35 minutes. Overall duration of fluoroscopy was 22 ± 18 minutes. Mean radiation dose was 66 mGy (range, 24 - 82). The mean length of CEUS final control was 8 ± 2 minutes. No type I or type III endoleak was detected either at CEUS or at angio-CT scan at one month from EVAR. CEUS revealed a type II endoleak in 6 patients (22%) , compared to 9 type II endoleaks (33%) detected at angio-CT scan one month after the procedure (p = 0.5).

CONCLUSIONS

Fully ultrasound (IVUS and CEUS) -assisted EVAR is safe, feasible and reliable, completely eliminating the need for iodine contrast medium and reducing the radiation exposure for both patients and surgeons.

Artificial Intelligence in Cardiovascular Medicine: Historical Overview, Current Status, and Future Directions

Artificial intelligence and machine learning are rapidly gaining popularity in every aspect of our daily lives, and cardiovascular medicine is no exception. Here, we provide physicians with an overview of the past, present, and future of artificial intelligence applications in cardiovascular medicine. We describe essential and powerful examples of machine-learning applications in industry and elsewhere. Finally, we discuss the latest technologic advances, as well as the benefits and limitations of artificial intelligence and machine learning in cardiovascular medicine.

Updates in Endovascular Procedural Navigation In Canadian Journal of Cardiology

There have been significant advancements in endovascular technology over the past decade. Increasingly complex disease processes are being addressed in a less invasive fashion, while still relying on standard two-dimensional, gray-scale fluoroscopy imaging to guide the procedures. With the advent of flat panel detectors as standard on fluoroscopy units and the utilization of fluoroscopy cone-beam computed tomography, the development of improved imaging tools has occurred which will help improve the imaging modalities used to perform these endovascular procedures. . Fusion imaging, the overlay of pre-operative 3-dimensional computed tomography images helps interventionalists perform endovascular procedures. Building on this technology, improvements in its function and utilization have occurred with the additional application of artificial intelligence and machine learning - allowing the images to independently accommodate to changes in the visualized anatomy. Corresponding development of navigation systems, allowing for the tracking of endovascular tools within these images using either fiberoptics of electromagnetic field generators, are looking to improve the accuracy of the procedures while reducing the need for radiation and contrast agents. These tools are making a dramatic change in our ability to perform complex endovascular procedures, and are the future gold standard. Ultimately, these will allow procedures to occur more quickly and more safely.

Radiation-free Thoracic Endovascular Aneurysm Repair with Fiberoptic and Electromagnetic Guidance:A Phantom Study

PURPOSE

The purpose of this study was to evaluate the feasibility and accuracy of a radiation-free implantation of a thoracic aortic stent-graft employing fiberoptic and electromagnetic tracking in an anthropomorphic phantom.

MATERIALS AND METHODS

An anthropomorphic phantom was manufactured based on computed tomography angiography (CTA) data from a patient. An aortic stent-graft application system was equipped with a fiber Bragg gratings fiber and three electromagnetic sensors. The stent-graft was navigated in the phantom by three interventionalists using the tracking data generated by both technologies. One implantation procedure was performed. The technical success of the procedure was evaluated using digital subtraction angiography and pre- and post-interventional CTA. Tracking accuracy was determined at various anatomical landmarks based on separately acquired fluoroscopic images. The mean/maximum errors were measured for the stent-graft application system and the tip/end of the stent-graft.

RESULTS

The procedure resulted in technical success with a mean error below 3 mm for the entire application system and <2 mm for the position of the tip of the stent-graft. Navigation/implantation and handling of the device were rated sufficiently accurate and on a par with comparable, routinely used stent-graft application systems.

CONCLUSION

Our study demonstrates successful stent-graft implantation during a thoracic endovascular aortic repair procedure employing advanced guidance techniques and avoiding fluoroscopic imaging. This is an essential step in facilitating the implantation of stent-grafts and reducing the health risks associated with ionizing radiation during endovascular procedures.

Fiber Optic RealShape technology in endovascular surgery

Fiber Optic RealShape technology is a new endovascular guidance system that aims to simplify endovascular procedures by improving wire, catheter, and device visualization, while reducing reliance on ionizing radiation. Developed by Philips, the system uses light refracted through optical fibers to generate real-time renderings of wires and catheters in three-dimensional space. Currently, devices with embedded Fiber Optic RealShape technology are being studied in human patients undergoing endovascular procedures. Early findings demonstrate the technology to be safe and effective in offsetting procedural complexity. Research and development to improve rendering accuracy and expand the selection of available Fiber Optic RealShape-enabled endovascular devices continues.

Incidence, predictive factors, and outcomes of intraprocedure adverse events during fenestrated-branched endovascular aortic repair of complex abdominal and thoracoabdominal aortic aneurysms

OBJECTIVE

To evaluate the incidence of intraoperative adverse events (IAEs) and their impact on outcomes after fenestrated-branched endovascular aortic repair (FB-EVAR) of complex abdominal aortic aneurysms and thoracoabdominal aortic aneurysm (TAAAs).

METHODS

We reviewed the clinical and imaging data of 600 consecutive patients (445 males; mean age, 75 ± 8 years) who underwent FB-EVAR between 2007 and 2019 in a single institution. IAE was defined as any intraoperative complication or technical problem requiring additional and unplanned procedures, and was classified as access-related, target artery (TA)-related, or graft-related. End points included rates of IAEs, 30-day or in-hospital mortality, major adverse events, patient survival, freedom from secondary intervention, and TA instability.

RESULTS

A total of 122 IAEs were identified in 105 patients (18%). IAEs were TA-related in 55 patients (9%), access-related in 46 patients (8%), and graft-related in seven patients (1%). Female sex was more frequent among patients with IAEs (44% vs 22%; P < .001). Patients with IAEs had smaller renal artery diameter (-0.4 mm, 5.4 ± 0.8 mm vs 5.8 ± 0.9 mm; P < .001), and were treated more often for TAAAs (72% vs 54%; P < .03). Technical success was achieved in 96.5% of patients and was lower for patients with IAEs (82% vs 99%; P < .001). Major adverse events were significantly more frequent among patients who had IAEs (odds ratio [OR], 1.98; 95% confidence interval [CI], 1.21-3.25), most due to acute kidney injury (27% vs 11%; P < .001) including new-onset dialysis (5% vs 1%; P = .01). On multivariate logistic regression model, female sex (OR, 2.5; 95% CI, 1.5-4.0), TA stenosis >50% (OR, 2.0; 95% CI, 1.3-3.3), and Crawford Extent II TAAA (OR, 1.9; 95% CI, 1.1-3.3) were predictive of IAEs, whereas preloaded design (OR, 0.6; 95% CI, 0.4-0.9) and TA diameter (+1 mm; OR, 0.6; 95% CI, 0.4-0.9) were protective of IAEs. IAEs negatively affected secondary intervention (hazard ratio [HR], 1.6; 95% CI, 1.1-2.3) and TA instability (HR, 2.5; 95% CI, 1.2-5.4); however, IAEs did not affect patient survival (HR, 1.0; 95% CI, 0.7-1.4).

CONCLUSIONS

IAEs are common, occurring in nearly one of five patients treated with FB-EVAR for complex aortic aneurysms, and have a negative impact on clinical outcomes. IAEs were associated with female sex, TA diameter, and more extensive aortic disease.

[Innovations in the endovascular treatment of peripheral arterial disease]

Die Kooperation von Medizinern, Ingenieuren und anderen Naturwissenschaften bringt weiterhin effektive Produkte auf den Markt, die dazu geeignet sind, die Dominanz der endovaskulären Techniken im Bereich der peripheren arteriellen Verschlusskrankheit (pAVK) weiter auszubauen. Begleitend werden zunehmend bildgebende Verfahren weiterentwickelt oder neu entwickelt, die helfen können, die Strahlenbelastung für Patient und Anwender trotz wachsender Zahlen strahlenbasierter Therapieverfahren deutlich zu reduzieren. Mittlerweile haben wir ein Materialportfolio an der Hand, das es erlaubt, jede Gefäßregion endovaskulär zu behandeln. Auf der anderen Seite dürfte das endovaskuläre Leistungsgefüge nicht flächendeckend homogen gestaltet sein und die jeweilige Ergebnisqualität dann für die Chirurgie sprechen. In diesem Übersichtsartikel sollen neue Materialien und neuere Ergebnisse vorgestellt werden, die den Bereich der endovaskulären Behandlung der pAVK in allen Gefäßsegmenten mit beeinflussen dürften.