Mesoscopic engineering materials for visual detection and selective removal of copper ions from drinking and waste water sources

Ultrasensitive Visual Tracking of Toxic Cyanide Ions in Biological Samples Using Biocompatible Metal-Organic Frameworks Architectures

The extraordinary accumulation of cyanide ions within biological cells is a severe health risk. Detecting and tracking toxic cyanide ions within these cells by simple and ultrasensitive methodologies are of immense curiosity. Here, continuous tracking of ultimate levels of CN--ions in HeLa cells was reported employing biocompatible branching molecular architectures (BMAs). These BMAs were engineered by decorating colorant-laden dendritic branch within and around the molecular building hollows of the geode-shelled nanorods of organic-inorganic Al-frameworks. Batch-contact methods were utilized to assess the potential of hollow-nest architecture for inhibition/evaluation of toxicant CN--ions within HeLa cells. The nanorod BMAs revealed significant potential capabilities in monitoring and tracking of CN- ions (88 parts per trillion) in biological trials within seconds. These results demonstrated sufficient evidence for the compatibility of BMAs during HeLa cell exposure. Under specific conditions, the BMAs were utilized for in-vitro fluorescence tracking/sensing of CN- in HeLa cells. The cliff swallow nest with massive mouths may have the potential to reduce the health hazards associated with toxicant exposure in biological cells.

Comparative study between three carbonaceous nanoblades and nanodarts for antimicrobial applications

The design of nanostructured materials occupies a privileged position in the development and management of affordable and effective technology in the antibacterial sector. Here, we discuss the antimicrobial properties of three carbonaceous nanoblades and nanodarts materials of graphene oxide (GO), reduced graphene oxide (RGO), and single-wall carbon nanotubes (SWCNTs) that have a mechano-bactericidal effect, and the ability to piercing or slicing bacterial membranes. To demonstrate the significance of size, morphology and composition on the antibacterial activity mechanism, the designed nanomaterials have been characterized. The minimum inhibitory concentration (MIC), standard agar well diffusion, and transmission electron microscopy were utilized to evaluate the antibacterial activity of GO, RGO, and SWCNTs. Based on the evidence obtained, the three carbonaceous materials exhibit activity against all microbial strains tested by completely encapsulating bacterial cells and causing morphological disruption by degrading the microbial cell membrane in the order of RGO > GO > SWCNTs. Because of the external cell wall structure and outer membrane proteins, the synthesized carbonaceous nanomaterials exhibited higher antibacterial activity against Gram-positive bacterial strains than Gram-negative and fungal microorganisms. RGO had the lowest MIC values (0.062, 0.125, and 0.25 mg/mL against B. subtilis, S. aureus, and E. coli, respectively), as well as minimum fungal concentrations (0.5 mg/mL for both A. fumigatus and C. albicans). At 12 hr, the cell viability values against tested microbial strains were completely suppressed. Cell lysis and death occurred as a result of severe membrane damage caused by microorganisms perched on RGO nanoblades. Our work gives an insight into the design of effective graphene-based antimicrobial materials for water treatment and remediation.

Preparation of basic magnesium carbonate nanosheets modified pumice and its adsorption of heavy metals

Heavy metal pollution in wastewater poses a grave danger to the environment and the human body. Pumice is a mineral with abundant reserves and low prices, and its prospect of heavy metal adsorbent is very broad. In this work, we modified pumice with basic magnesium carbonate nanosheets by a convenient hydrothermal synthesis. The adsorption capacity of heavy metals is greatly improved. The effects of different pH and adsorption dosages are investigated. All the optimum pH values for Cu2+, Pb2+, and Cd2+ are 5. The adsorption of three kinds of ions conforms to the quasi-second-order adsorption kinetics model. The theoretical adsorption capacities of Cu2+, Pb2+, and Cd2+, which are calculated by the Langmuir model, are 235.29 mg/L, 595.24 mg/L, and 370.34 mg/L, respectively. The adsorption of Cu2+ and Cd2+ fit the Langmuir model better. The Freundlich model is fitted well with the adsorption of Pb2+. In the experiment simulating real wastewater, the adsorption capacity of heavy metals is not affected. It also shows good reusability in three regeneration cycles. And Mg5(CO3)4(OH)2·4H2O@pumice adsorption column showed the good removal efficiency of three heavy metals at different concentrations and different spatial velocities in the column experiment. Thus, it is believed that the Mg5(CO3)4(OH)2·4H2O@pumice is a promising adsorbent for the efficient removal of heavy metals.

Selective adsorption of tetracycline and copper(II) on ion-imprinted porous alginate microspheres: performance and potential mechanisms

A novel epichlorohydrin and thiourea grafted porous alginate adsorbent (UA-Ca/IIP) was synthesized using ion-imprinting and direct templating to remove copper ions (Cu(II)) and tetracycline (TC) in aqueous solution. UA-Ca/IIP demonstrated great selectivity for Cu(II) and TC among different coexisting anions (CO32-, PO43- and SO42-), cations (Ca2+, Mg2+ and NH4+), and antibiotics (oxytetracycline and sulfamethoxazole). The adsorption of TC and Cu(II) by UA-Ca/IIP was significantly affected by the pH of the solution, and the quantity of TC and Cu(II) adsorbed reached a maximum at pH 5. A pseudo-second-order model better fitted the kinetic data; the Langmuir model predicted the maximum adsorption quantities 3.527 mmol TC g-1 and 4.478 mmol Cu(II) g-1 at 298 K. Thermodynamic studies indicated that the TC and Cu(II) adsorption was more rapid at a higher temperature. Antagonistic and synergistic adsorption experiments showed that the adsorption capacity of TC would increase significantly with the increase of Cu(II) concentration. Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy indicated that along with the influence of pH, electrostatic interaction and complexation were the main mechanisms of TC and Cu(II) adsorption. Regeneration experiments revealed that TC and Cu(II) were removed efficiently and that UA-Ca/IIP was recyclable over the long term. These results show that the modified porous alginate microsphere is a green and recyclable adsorbent, which has good selectivity and high adsorption performance for the removal of TC and Cu(II).

Insights into heavy metal tolerance mechanisms of Brassica species: physiological, biochemical, and molecular interventions

Heavy metal (HM) contamination of soil due to anthropogenic activities has led to bioaccumulation and biomagnification, posing toxic effects on plants by interacting with vital cellular biomolecules such as DNA and proteins. Brassica species have developed complex physiological, biochemical, and molecular mechanisms for adaptability, tolerance, and survival under these conditions. This review summarizes the HM tolerance strategies of Brassica species, covering the role of root exudates, microorganisms, cell walls, cell membranes, and organelle-specific proteins. The first line of defence against HM stress in Brassica species is the avoidance strategy, which involves metal ion precipitation, root sorption, and metal exclusion. The use of plant growth-promoting microbes, Pseudomonas, Psychrobacter, and Rhizobium species effectively immobilizes HMs and reduces their uptake by Brassica roots. The roots of Brassica species efficiently detoxify metals, particularly by flavonoid glycoside exudation. The composition of the cell wall and callose deposition also plays a crucial role in enhancing HMs resistance in Brassica species. Furthermore, plasma membrane-associated transporters, BjCET, BjPCR, BjYSL, and BnMTP, reduce HM concentration by stimulating the efflux mechanism. Brassica species also respond to stress by up-regulating existing protein pools or synthesizing novel proteins associated with HM stress tolerance. This review provides new insights into the HM tolerance mechanisms of Brassica species, which are necessary for future development of HM-resistant crops.

A review of various strategies in e-waste management in line with circular economics

Waste management of electrical and electronic equipment has become a key challenge for electronics manufacturers due to globalization and the rapid expansion of information technology. As the volume of e-waste grows, legal departments lack the infrastructure, technology, and ability to collect and manage it environmentally soundly. Government laws, economic reasons, and social issues are important considerations in e-waste management. The circular economy concept is built on reusing and recycling goods and resources. A novel idea called the circular economy might prevent the negative consequences brought on by the exploitation and processing of natural resources while also having good effects such as lowering the demand for raw materials, cutting down on the use of fundamental resources, and creating jobs. To demonstrate the significance of policy implementation, the necessity for technology, and the need for societal awareness to build a sustainable and circular economy, the study intends to showcase international best practices in e-waste management. This study uses circular economy participatory implementation methods to provide a variety of possible approaches to assist decision-makers in e-waste management. The purpose of this article is to review the most accepted methods for e-waste management to emphasize the importance of implementing policies, technology requirements, and social awareness in creating a circular economy. To conclude, this paper highlights the necessity of a common legal framework, reform of the informal sector, the responsibility of different stakeholders, and entrepreneurial perspectives.

Click derived organosilane assembled with nano platform for the detection of Cu2+ ions: Biological evaluation and molecular docking approach

Metal ions have active roles in biochemical, industrial, and environmental processes. The design and development of new rapid sensing materials with advanced reasonable, compelling, and convenient, techniques are urgent. Here in this work, we design and develop sensor with the facile amalgamation of the pyrene-based organosilane (5) through a click silylation approach silicon composite for selective detection of Cu²⁺ ions. Physicochemical and keen methods are employed to perceive the resultant hybrid nanoparticles (H-NPs), and these nanocomposites similarly displayed a strong affection for Cu²⁺ ions. In addition, the identification restrictions while utilizing 5 and H-NP's towards Cu²⁺ found in this study are far lower than the WHO rules for drinking water. Further, organosilane (5) shows good antibacterial and antioxidant activity. The antibacterial effects of triazole-based organosilane (5), are evaluated with a molecular docking study with Escherichia coli (IJZQ) was conducted. The selected ligand was revealed to have a reasonable docking score with a binding energy of -8.40 kcal mol^-1.

Metal-organic frameworks (MOFs) based luminescent and electrochemical sensors for food contaminant detection

With the increasing population, food toxicity has become a prevalent concern due to the growing contaminants of food products. Therefore, the need for new materials for toxicant detection and food quality monitoring will always be in demand. Metal-organic frameworks (MOFs) based on luminescence and electrochemical sensors with tunable porosity and active surface area are promising materials for food contaminants monitoring. This review summarizes and studies the most recent progress on MOF sensors for detecting food contaminants such as pesticides, antibiotics, toxins, biomolecules, and ionic species. First, with the introduction of MOFs, food contaminants and materials for toxicants detection are discussed. Then the insights into the MOFs as emerging materials for sensing applications with luminescent and electrochemical properties, signal changes, and sensing mechanisms are discussed. Next, recent advances in luminescent and electrochemical MOFs food sensors and their sensitivity, selectivity, and capacities for common food toxicants are summarized. Further, the challenges and outlooks are discussed for providing a new pathway for MOF food contaminant detection tools. Overall, a timely source of information on advanced MOF materials provides materials for next-generation food sensors.

Landfill leachate a new threat to water quality: a case study from the Temperate Himalayas

Landfills are commonly seen as the most cost-efficient and practical approach to waste management in various regions around the world. Nonetheless, the infiltration of hazardous materials from poorly managed dumping sites remains a significant environmental issue in most developing countries such as India. Leachate serves as a prominent point source of contamination in many environmental media like soil, groundwater, and surface water around the world. So the prime issues humans are experiencing are associated with water quality. Thus, the investigation was undertaken to assess the impact of leachate from the Achan landfill on surface water quality in the Temperate Himalayas. Monitoring was done during in all four seasons, viz., spring, summer, autumn, and winter. Among the sites, the leachate outflow site was found to have the highest mean value of pH (7.95), EC (2.16 dS/m), total nitrogen (2.64 mg/l), P (4.75 mg/l), K (1.41 mg/l), Ca (107.45 mg/l), Mg (54.93 mg/l), Zn (0.8 mg/l), Fe (1.78 mg/l), Cu (0.66 mg/l), Mn (0.81 mg/l), BOD (21.47 mg/l), COD (66.24 mg/l), temperature (14.22 °C), turbidity (14.29 NTU), while lowest mean values of all parameters were recorded at control site. Among the seasons, summer season was found to have maximum value of pH (7.9), EC (2.36 dS/m), total nitrogen (2.54 mg/l), P (4.0 mg/l), K (0.89 mg/l), Ca (85.94 mg/l), Mg (43.91 mg/l), Fe (1.4 mg/l), Cu (0.52 mg/l), Mn (0.64 mg/l), BOD (22.82 mg/l), COD (65.87 mg/l), temperature (18.99 °C), and turbidity (8.49 NTU). The maximum mean value of Zn (0.66 mg/l) was recorded during winter season, while other parameters were found to be minimum during winter season. From this study, we concluded that a decreasing trend was observed during all the seasons in the concentration of all physico-chemical parameters with an increase in distance from the landfill. So it is recommended that the leachate should be treated at the source before disposing into the water body and the landfill should be lined properly to prevent the entry of leachate into water sources.

Visual and Real-Time Monitoring of Cd2+ in Water, Rice, and Rice Soil with Test Paper Based on [2 + 2] Lanthanide Clusters

Cadmium ions (Cd²⁺) are highly toxic to animal and human health, especially through the drinking of Cd²⁺-contaminated water and eating Cd²⁺-contaminated rice. Therefore, accurate detection of Cd²⁺ in water, rice, and rice soil is urgent. In this work, two [2 + 2] lanthanide clusters of Tb₂Tb₂ and Eu₂Eu₂ were synthesized and characterized in detail. Interestingly, Tb2Tb2 is a rapid sensor for Cd²⁺ through luminescence "turn-off". Further studies show that Tb2Tb2 is a highly sensitive and selective sensor toward Cd²⁺ in water, rice supernatants, and rice soil supernatants, with a very short response time of 20 s. The limit of detection (LOD) in the above three real samples is as low as 0.0112, 1.1240, and 0.1124 ppb, respectively, which is lower than the national standards for food safety in China (GB 2762-2022). More interestingly, a portable sensing device of test paper based on Tb2Tb2 is developed with a facile method, which shows visible, highly sensitive, and selective sensing toward Cd²⁺ in real samples of water, rice supernatants, and rice soil supernatants. Tb2Tb2 and its sensing device of test paper are an on-site analysis sensor for potentially non-expert users, especially for people in remote rural areas.

Facile Synthesis of the Polyaniline@Waste Cellulosic Nanocomposite for the Efficient Decontamination of Copper(II) and Phenol from Wastewater

The existence of heavy metals and organic pollutants in wastewater is a threat to the ecosystem and a challenge for researchers to remove using common technology. Herein, a facile one-step in situ oxidative polymerization synthesis method has been used to fabricate polyaniline@waste cellulosic nanocomposite adsornt, polyaniline-embedded waste tissue paper (PANI@WTP) to remove copper(II) and phenol from the aqueous solution. The structural and surface properties of the synthesized materials were examined by XRD, FTIR, TEM, and a zeta potential analyzer. The scavenging of the Cu(II) and phenol onto the prepared materials was investigated as a function of interaction time, pollutant concentration, and solution pH. Advanced kinetics and isotherms modeling is used to explore the Cu(II) ion and phenol adsorption mechanisms. The synthesized PANI@WTP adsorbent showed a high intake capacity for Cu(II) than phenol, with the maximum calculated adsorption capacity of 605.20 and 501.23 mg g^-1, respectively. The Langmuir equilibrium isotherm model is well-fitted for Cu(II) and phenol adsorption onto the PANI@WTP. The superior scavenging capability of the PANI@WTP for Cu(II) and phenol could be explained based on the host-guest interaction forces and large active sites. Moreover, the efficiency of the PANI@WTP for Cu(II) and phenol scavenging was excellent even after the five cycles of regeneration.

Efficient removal of noxious methylene blue and crystal violet dyes at neutral conditions by reusable montmorillonite/NiFe2O4@amine-functionalized chitosan composite

The jeopardy of the synthetic dyes effluents on human health and the environment has swiftly aggravated, threatening human survival. Hence, sustained studies have figured out the most acceptable way to eliminate this poisonous contaminant. Thereby, our investigation aimed to fabricate montmorillonite/magnetic NiFe₂O₄@amine-functionalized chitosan (MMT-mAmCs) composite as a promising green adsorbent to remove the cationic methylene blue (MB) and crystal violet (CV) dyes from the wastewater in neutral conditions. Interestingly, MMT-mAmCs composite carries high negative charges at a wide pH range from 4 to 11 as clarified from zeta potential measurements, asserting its suitability to adsorb the cationic contaminants. In addition, the experimental study confirmed that the optimum pH to adsorb both MB and CV was pH 7, inferring the ability of MMT-mAmCs to adsorb both cationic dyes in simple process conditions. Furthermore, the ferromagnetic behavior of the MMT-mAmCs composite is additional merit to our adsorbent that provides facile, fast, and flawless separation. Notably, the as-fabricated composite revealed an auspicious adsorbability towards the adsorptive removal of MB and CV, since the maximum adsorption capacity of MB and CV were 137 and 118 mg/g, respectively. Moreover, the isotherm and kinetic investigatins depicted that the adsorption of both cationic dyes fitted Langmuir and Pseudo 2nd order models, respectively. Besides, the advanced adsorbent preserved satisfactory adsorption characteristics with maximal removal efficacy exceeding 87% after reuse for ten consecutive cycles. More importantly, MMT-mAmCs efficiently adsorbed MB and CV from real agricultural water, Nile river water and wastewater samples at the neutral pH medium, reflecting its potentiality to be a superb reusable candidate for adsorptive removal cationic pollutants from their aquatic media.

Highly Selective Colorimetric Detection of Cu2+ Using EDTA-Complexed Chlorophyll-Copper/ZnO Nanorods with Cavities Specific to Cu2+ as a Light-Activated Nanozyme

In this study, chlorophyll-copper (ChlCu)-modified ZnO nanorods (ChlCu/ZnO) were prepared, and then sodium ethylenediamine tetraacetate (EDTA) was used to remove part of Cu²⁺ in ChlCu, leaving cavities with specific adsorption activity for Cu²⁺ in E-ChlCu/ZnO. Appropriate EDTA treatment improved the photoactivity of ChlCu/ZnO and the adsorption selectivity to Cu²⁺. However, excessive EDTA treatment might lead to the collapse of the ChlCu structure, resulting in a decrease in photoactivity. The E-ChlCu/ZnO sample with 8 h of ChlCu treatment and 2 h of EDTA treatment showed optimal photoactivity. The as-prepared E-ChlCu/ZnO exhibited activity as a light-activated nanozyme, which could oxidize 3,3',5,5'-tetramethylbenzidine (TMB) to blue under illumination, but when Cu²⁺ was present in the solution, this colorimetric reaction was inhibited; therefore, E-ChlCu/ZnO could be used for colorimetric detection of Cu²⁺. Because of the existence of specific cavities, E-ChlCu/ZnO showed excellent detection selectivity, a wide linear detection range (0-1 and 1-15 μM), and a low detection limit (0.024 μM) in the colorimetric detection of Cu²⁺.

Nitrate adsorption onto surface-modified red mud in batch and fixed-bed column systems: equilibrium, kinetic, and thermodynamic studies

This research aimed to develop a novel composite as a low-cost adsorbent for the removal of nitrate ion from aqueous solutions. The characterization of this composite (composition of red mud with dimethyldioctadecylammonium bromide (DDAB)) was performed by XRF, XRD, FTIR, and BET analyses. The most influential variables on nitrate adsorption, including contact time, solution acidity, adsorbent amount, and temperature were studied. The maximum amount of nitrate adsorbed onto the prepared adsorbent was obtained at pH 5.5 and contact time 30 min. The heterogeneous adsorption occurred during the uptake of nitrate. The results of kinetic study revealed that intra-particle diffusion was the major limitation for nitrate adsorption rate. The values of thermodynamic parameters illustrate the non-spontaneous, associative, and exothermic adsorption process. Increasing the temperature enhances the tendency of the process to non-spontaneously. Research on fixed-bed column has been done under different initial nitrate concentrations. The adsorption capacity of nitrate was increased with an increase in the initial concentration of nitrate. The results of column data were successfully explained using the Thomas and Yoon-Nelson models.

Development of new magnetic adsorbent of walnut shell ash/starch/Fe3O4 for effective copper ions removal: Treatment of groundwater samples

The goal of this investigation was to develop a new magnetic nanocomposite of walnut shell ash (WSA)/starch/Fe₃O₄ to remove Cu (II) present in groundwater samples. The desired nanocomposites were successfully synthesized by the chemical deposition method. The specific active surface area for pristine WSA and WSA/starch/Fe₃O₄ magnetic nanocomposites was determined to be 8.1 and 52.6 m²/g, respectively. A central composite design for the response surface method was utilized to study the influence of pH, adsorbent quantity, initial content of Cu (II), temperature, and contact time. This method showed the success of the model to design process variables and to estimate the appropriate response. The P- and F-value determined for the quadratic polynomial model showed the significance and accuracy of the proposed model in examining experimental and predicted data with R² and Adj.R² of 0.994 and 0.991, respectively. The Cu adsorption onto WSA and WSA/starch/Fe₃O₄ obeyed the Freundlich and Langmuir models, respectively. The highest Cu (II) sorption capacity of 29.0 and 45.4 mg/g was attained for WSA and WSA/starch/Fe₃O₄, respectively. The free energy of Gibbs had a negative value at 25-45 °C indicating that the adsorption process is spontaneous. Also, negative ΔH values for copper adsorption showed that the processes are exothermic. The kinetic adsorption data for WSA and WSA/starch/Fe₃O₄ followed the pseudo-second order (PSO) model. The ability of the composite adsorbent to remove copper from three groundwater samples showed that it could be reused at least 3 times with appropriate efficiency, depending on the water quality.

A novel spectrofluorimetric method based on a reaction with an azoisoxazoles-benzenesulfonamide derivative for determination of uranium (VI) ions in water samples

Selective fluorometric detection and determination of uranium ions is provided here using a novel fluorescent reagent, namely (E)-4-([4-hydroxynaphthalen-1-yl]diazenyl)-N-(5-methyleisoxazol-3-yl) benzenesulfonamide (UVI reagent). The UVI reagent offers a selective fluorescence enhancement behaviour at emission wavelength = 557 nm. The parameters affecting fluorometric detection of uranium ions, such as the pH, solvent type, ligand concentration, interaction time, and interfering ions, were investigated and adjusted. The proposed UVI reagent can detect and determine uranium ions even at low concentrations, for which the obtained limit of detection was 0.1 ppm. Additionally, this proposed determination protocol was successfully used to detect, monitor, and determine uranium ions in actual water samples.

Removal of U(vi) from aqueous solutions by an effective bio-adsorbent from walnut shell and cellulose composite-stabilized iron sulfide nanoparticles

FeS nanoparticles were easily aggregated and oxidized in the natural environment. It was important to stabilize the iron sulfide nanoparticle composite with a stabilizer. Biochar could be used as an effective carrier to inhibit the agglomeration and oxidization of FeS nanoparticles. An efficient and novel bio-adsorbent (CFeS-WS) from walnut shell (WS) and cellulose composites-stabilized iron sulfide nanoparticle was synthesized by the modified method. The removal of U(vi) ions from an aqueous solution by CFeS-WS was carried out. The experimental results indicated that numerous functional groups were observed on the surface of CFeS-WS. In addition, the biochar was loaded successfully with cellulose and FeS nanoparticle composites. The cellulose and biochar effectively prevented the agglomeration of FeS nanoparticles. The adsorption process of U(vi) ions by CFeS-WS was more consistent with the pseudo second-order kinetic model and Langmuir isotherm model. The adsorption process of U(vi) ions was an endothermic and chemical reaction process. The proposed reaction mechanism of the U(vi) ion removal by CFeS-WS mainly consisted of the ion exchange reaction, reduction reaction, hydrogen bonding and functional group, and pore of the adsorbent filling. According to the results of the recycle experiment, it indicated that the chemical stability of CFeS-WS was good.

Simultaneous Visual Detection and Removal of Cu2+ with Electrospun Self-Supporting Flexible Amidated Polyacrylonitrile/Branched Polyethyleneimine Nanofiber Membranes

Sensitive detection and effective removal of copper ions (Cu²⁺) from water are still arduous tasks required to protect public health and environmental safety because of the serious impacts of Cu²⁺ on humans and other organisms. Herein, we report the design and fabrication of self-supporting flexible amidated polyacrylonitrile/branched polyethyleneimine nanofiber membranes (abbreviated as aPAN/BPEI NMs) via facile electrospinning and a subsequent hydrothermal method, which are used not only as strips for the visual detection of Cu²⁺ but also as effective adsorbents for the removal of Cu²⁺ from water. Because aPAN/BPEI NMs are self-supporting, they can be easily removed from the solution to reduce secondary pollution to the environment. Based on the high Cu²⁺ binding capacity of BPEI, Cu²⁺ ions are adsorbed on the aPAN/BPEI NMs, which leads to the appearance of new absorbance bands at 280 and 636 nm and a color change from yellow to blue. aPAN/BPEI NMs are utilized for the visual detection of Cu²⁺ with a linear range of 50-700 μM and limits of detection of 11.5 and 4.8 μM (absorption peaks at 280 and 636 nm). More importantly, aPAN/BPEI NMs exhibit excellent selectivity and certain recovery with a simple treatment. Furthermore, by utilizing the adsorption characteristics of Cu²⁺ in aqueous media, it can be effectively removed by aPAN/BPEI NMs with a remarkable adsorption capacity of 209.53 mg·g^-1. Additionally, the removal of Cu²⁺ by aPAN/BPEI NMs does not exhibit interference by other foreign ions. The adsorption process conforms well to the pseudo-second order (PSO) kinetic model and Jovanovich model, proving that adsorption occurs via chemical and monolayer adsorption mechanisms. Accordingly, this work will provide theoretical and technical support for the design and fabrication of novel heavy metal ion detection-removal integrated materials exhibiting high sensitivity and strong adsorption.