The physical and chemical properties of the polyvinylalcohol/polyvinylpyrrolidone/hydroxyapatite composite hydrogel

Novel Antibacterial and Biocompatible Nanostructured Gels Based on One-step Synthesis as a Potential Disinfectant for Endodontic Infection Control

AIM

The objective of this study was to develop nanostructured gels as biocompatible intracanal disinfectants by one-step microwave radiation-assisted synthesis.

METHODS

Polyvinyl alcohol (PVA) and polyvinyl pyrrolidone (PVP) were used as a support network, and polyethylene glycol (PEG) was used as a reducing agent. The gels were characterized by measuring the swelling ratio (SR) and rheological properties and by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and atomic force microscopy (AFM). The antibacterial effects of each gel were evaluated against the endodontic clinical strain Enterococcus faecalis. Then, the viability of the 21-day mature multispecies bacterial biofilm was assessed using confocal microscopy in an ex vivo model, where the biofilm was exposed to the mix of nanogels. The cell proliferation, viability, and morphology of human periodontal ligament (HPDL) cells were quantified using a real-time IncuCyte® S3 Live-Cell System. Viability was measured by confocal microscopy using an ex vivo model exposing a 21-day mature multispecies bacterial biofilm to the mix of nanogels.

RESULTS

The antibacterial activity of the gels coincided with the superficial characterization and the solubility of the gel in the growth medium. Gels with higher viscosity (327.85-980.58 Pa s), higher dissolution (42-70%SR), and lower porosity (no porosity and 611.63 nm) showed excellent antibacterial activity against E. faecalis. Despite their physicochemical characteristics, CuNPs gels showed greater effectiveness against E. faecalis.These nanostructured gels with high PVA concentrations promote HPDL cells proliferation while still exerting antibacterial properties. Mix of nanogels showed an increase non-viable cells biomass from at of application.

CONCLUSIONS

The use of biocompatible polymers influences the physicochemical, bactericidal, and cytotoxic response, making these materials potential disinfectant agents against resistant bacteria with good biocompatibility and improved HPDL cells proliferation.

Preparation of lignin-based hydrogels, their properties and applications

Polymers obtained from biomass are a concerning alternative to petro-based polymers because of their low cost of manufacturing, biocompatibility, ecofriendly and biodegradability. Lignin as the second richest and the only polyaromatics bio-polymer in plant which has been most studied for the numerous applications in different fields. But, in the past decade, the exploitation of lignin for the preparation of new smart materials with improved properties has been broadly sought, because lignin valorization plays one of the primary challenging issues of the pulp and paper industry and lignocellulosic biorefinery. Although, well suited chemical structure of lignin comprises of many functional hydrophilic and active groups, such as phenolic hydroxyls, carboxyls and methoxyls, which provides a great potential to be applied in the preparation of biodegradable hydrogels. In this review, lignin hydrogel is covered with preparation strategies, properties and applications. This review reports some important properties, such as mechanical, adhesive, self-healing, conductive, antibacterial and antifreezing properties were then discussed. Furthermore, herein also reviewed the current applications of lignin hydrogel, including dye adsorption, smart materials for stimuli sensitive, wearable electronics for biomedical applications and flexible supercapacitors. Overall, this review covers recent progresses regarding lignin-based hydrogel and constitutes a timely review of this promising material.

Polyvinylpyrrolidone-Alginate-Carbonate Hydroxyapatite Porous Composites for Dental Applications

An alternative approach for the currently used replacement therapy in dentistry is to apply materials that restore tooth tissue. Among them, composites, based on biopolymers with calcium phosphates, and cells can be applied. In the present work, a composite based on polyvinylpyrrolidone (PVP) and alginate (Alg) with carbonate hydroxyapatite (CHA) was prepared and characterized. The composite was investigated by X-ray diffraction, infrared spectroscopy, electron paramagnetic resonance (EPR) and scanning electron microscopy methods, and the microstructure, porosity, and swelling properties of the material were described. In vitro studies included the MTT test using mouse fibroblasts, and adhesion and survivability tests with human dental pulp stem cells (DPSC). The mineral component of the composite corresponded to CHA with an admixture of amorphous calcium phosphate. The presence of a bond between the polymer matrix and CHA particles was shown by EPR. The structure of the material was represented by micro- (30-190 μm) and nano-pores (average 8.71 ± 4.15 nm). The swelling measurements attested that CHA addition increased the polymer matrix hydrophilicity by 200%. In vitro studies demonstrated the biocompatibility of PVP-Alg-CHA (95 ± 5% cell viability), and DPSC located inside the pores. It was concluded that the PVP-Alg-CHA porous composite is promising for dentistry applications.

Targeted release of soybean peptide from CMC/PVA hydrogels in simulated intestinal fluid and their pharmacokinetics

Carboxymethyl cellulose (CMC)/polyvinyl alcohol (PVA) hydrogels loaded with soybean peptide (SPE) were fabricated via a freeze-thaw method. These hydrogels conquer barriers in simulated gastric fluid (SGF), and then release SPE in simulated intestinal fluid (SIF). The results of in vitro SPE release from these hydrogels showed that in SGF only a little of the SPE released, but in SIF the SPE was completely released. The released SPE had scavenging rates for DPPH and ABTS free radicals of 41.68 and 31.43 %. The pharmacokinetic model of SPE release from the hydrogels in SIF was studied. When the hydrogels are moved from SGF to SIF, the sorption of the shrinkage hydrogel network is entirely controlled by stress-induced relaxations. There are swollen and shrunken regions during SPE release. For SPE release into the SIF, SPE has to be freed from the weak bonds in the swollen regions by changes in the conformation of CMC and PVA. The release rate of SPE was found to be governed by the diffusion and swelling rate of the shrinkage hydrogel network. The Korsmeyer-Peppas equation diffusion exponents (n) for SPE release from the hydrogels are >2.063, indicating a super case II transport. These data demonstrate CMC/PVA hydrogels have potential applications in oral peptide delivery.

Innovative Approaches and Advances for Hair Follicle Regeneration

Pathological hair loss (also known as alopecia) and shortage of hair follicle (HF) donors have posed an urgent requirement for HF regeneration. With the revelation of mechanisms in tissue engineering, the proliferation of HFs in vitro has achieved more promising trust for the treatments of alopecia and other skin impairments. Theoretically, HF organoids have great potential to develop into native HFs and attachments such as sweat glands after transplantation. However, since the rich extracellular matrix (ECM) deficiency, the induction characteristics of skin-derived cells gradually fade away along with their trichogenic capacity after continuous cell passaging in vitro. Therefore, ECM-mimicking support is an essential prelude before HF transplantation is implemented. This review summarizes the status of providing various epidermal and dermal cells with a three-dimensional (3D) scaffold to support the cell homeostasis and better mimic in vivo environments for the sake of HF regeneration. HF-relevant cells including dermal papilla cells (DPCs), hair follicle stem cells (HFSCs), and mesenchymal stem cells (MSCs) are able to be induced to form HF organoids in the vitro culture system. The niche microenvironment simulated by different forms of biomaterial scaffold can offer the cells a network of ordered growth environment to alleviate inductivity loss and promote the expression of functional proteins. The scaffolds often play the role of ECM substrates and bring about epithelial-mesenchymal interaction (EMI) through coculture to ensure the functional preservation of HF cells during in vitro passage. Functional HF organoids can be formed either before or after transplantation into the dermis layer. Here, we review and emphasize the importance of 3D culture in HF regeneration in vitro. Finally, the latest progress in treatment trials and critical analysis of the properties and benefits of different emerging biomaterials for HF regeneration along with the main challenges and prospects of HF regenerative approaches are discussed.

Reactive Oxygen Species-Responsive Gel-Based Microneedle Patches for Prolonged and Intelligent Psoriasis Management

Psoriasis is an inflammatory skin disease. Microneedle (MN) patches can improve psoriasis treatment outcomes by increasing local drug content in the skin. As psoriasis frequently relapses, developing intelligent MN-based drug delivery systems with prolonged therapeutic drug levels and improved treatment efficiency is of great significance. Here, we designed detachable H₂O₂-responsive gel-based MN patches containing methotrexate (MTX) and epigallocatechin gallate (EGCG) by using EGCG as both cross-linkers for needle-composited materials and anti-inflammatory drugs. The gel-based MNs had dual-mode drug release kinetics, which quickly released MTX diffusively and sustainably released EGCG in an H₂O₂-responsive way. Compared with dissolving MNs, the gel-based MNs extended skin retention of EGCG, leading to prolonged reactive oxygen species (ROS) scavenging effects. The ROS-responsive MN patches that transdermally delivered antiproliferative and anti-inflammatory drugs improved treatment outcomes in both psoriasis-like and prophylactic psoriasis-like animal models.

Strong adhesive and drug-loaded hydrogels for enhancing bone-implant interface fixation and anti-infection properties

The bonding strength of the bone-titanium (Ti) implant interface is critical for patients undergoing joint replacement. However, current bone adhesives used in clinic have shortcomings, such as biological inertness, cytotoxicity, and lack of osteogenic ability. In this study, a simple and low-cost hydrogel-based bone adhesive was prepared to improve the osseointegration ability and anti-infection ability of the bone-implant interface. A multifunctional hydrogel was prepared by incorporating nano-hydroxyapatite (HA) on polyethyleneimine (PEI) and polyacrylic acid (PAA) (PEI/PAA-HA). It was shown that PEI/PAA-HA hydrogel exhibited good self-healing and strong adhesive ability. The adhesive strengths of bone-Ti and Ti-Ti were measured as 2.30 ± 0.15 MPa and 1.07 ± 0.07 MPa, respectively. Vancomycin (VAN) was loaded into the PEI/PAA-HA hydrogel (PEI/PAA-HA-VAN) via a simple immersion method. The PEI/PAA-HA-VAN showed excellent antibacterial effect by sustained release of VAN. In addition, the PEI/PAA-HA-VAN hydrogel exhibited excellent cytocompatibility promoting the expression of osteogenic genes and the deposition of mineralized matrix. Collectively, this strong adhesive hydrogel showed great potential in enhancing bone-implant interface fixation.

Essential Oils as Antimicrobial Active Substances in Wound Dressings

Wound dressings for skin lesions, such as bedsores or pressure ulcers, are widely used for many patients, both during hospitalization and in subsequent treatment at home. To improve the treatment and shorten the healing time and, therefore, the cost, numerous types of wound dressings have been developed by manufacturers. Considering certain inconveniences related to the intolerance of some patients to antibiotics and the antimicrobial, antioxidant, and curative properties of certain essential oils, we conducted research by incorporating these oils, based on polyvinyl alcohol/ polyvinyl pyrrolidone (PVA/PVP) biopolymers, into dressings. The objective of this study was to study the potential of a polymeric matrix for wound healing, with polyvinyl alcohol as the main material and polyvinyl pyrrolidone and hydroxypropyl methylcellulose (HPMC) as secondary materials, together with additives (plasticizers poly(ethylene glycol) (PEG) and glycerol), stabilizers (Zn stearate), antioxidants (vitamin A and vitamin E), and four types of essential oils (fennel, peppermint, pine, and thyme essential oils). For all the studied samples, the combining compatibility, antimicrobial, and cytotoxicity properties were investigated. The obtained results demonstrated a uniform morphology for almost all the samples and adequate barrier properties for contact with suppurating wounds. The results show that the obtained samples containing essential oils have a good inhibitory effect on, or antimicrobial properties against, Staphylococcus aureus ATCC 25923, Enterococcus faecalis ATCC 29212, Escherichia coli ATCC 25922, Pseudomonas aeruginosa ATCC 27853, and Candida albicans ATCC 10231. The MTT assay showed that the tested samples were not toxic and did not lead to cell death. The results showed that the essential oils used provide an effective solution as active substances in wound dressings.

Formulation and Characterization of a New Injectable Bone Substitute Composed PVA/Borax/CaCO3 and Demineralized Bone Matrix

The occurrence of bone-related disorders and diseases has dramatically increased in recent years around the world. Demineralized bone matrix (DBM) has been widely used as a bone implant due to its osteoinduction and bioactivity. However, the use of DBM is limited because it is a particulate material, which makes it difficult to manipulate and implant with precision. In addition, these particles are susceptible to migration to other sites. To address this situation, DBM is commonly incorporated into a variety of carriers. An injectable scaffold has advantages over bone grafts or preformed scaffolds, such as the ability to flow and fill a bone defect. The aim of this research was to develop a DBM carrier with such viscoelastic properties in order to obtain an injectable bone substitute (IBS). The developed DBM carrier consisted of a PVA/glycerol network cross-linked with borax and reinforced with CaCO3 as a pH neutralizer, porosity generator, and source of Ca. The physicochemical properties were determined by an injectability test, FTIR, SEM, and TGA. Porosity, degradation, bioactivity, possible cytotoxic effect, and proliferation in osteoblasts were also determined. The results showed that the developed material has great potential to be used in bone tissue regeneration.

A Composite Hydrogel with High Mechanical Strength, Fluorescence, and Degradable Behavior for Bone Tissue Engineering

In this work, to obtain a novel composite hydrogel with high mechanical strength, fluorescence and degradable behavior for bone tissue engineering, we prepare a nanofiller and double-network (DN) structure co-enhanced carbon dots/hydroxyapatite/poly (vinyl alcohol) (CDs/HA/PVA) DN hydrogel. The composite hydrogels are fabricated by a combination of two fabrication techniques including chemical copolymerization and freezing‒thawing cycles, and further characterized by FTIR, XRD, etc. Additional investigations focus on the mechanical properties of the hydrogel with varying mass ratios of CDs to PVA, HA to PVA and different numbers of freezing/thawing cycles. The results show that the as-prepared CDs3.0/HA0.6/PVA DN9 hydrogel has optimized compression properties (Compression strength = 3.462 MPa, Young's modulus = 4.5 kPa). This is mainly caused by the synergism effect of the nanofiller and chemical and physical co-crosslinking. The water content and swelling ratio of the CDs/HA/PVA SN and DN gels are also systematically investigated to reveal the relationship of their microstructural features and mechanical behavior. In addition, in vitro degradation tests of the CDs/HA/PVA DN hydrogel show that the DN hydrogels have a prominent degradable behavior. So, they have potential to be used as high-strength, self-tracing bone substitutes in the biomedical engineering field.

Mechanical Properties and Microstructure of Polyvinyl Alcohol (PVA) Modified Cement Mortar

The mechanical properties of cement mortars with 0~2.0% (by mass) polyvinyl alcohol (PVA) were experimentally studied, and the effects of PVA incorporation on the hydration products and microstructure of the cement mortar were determined with differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The results show that the rational content of PVA formed evenly dispersed network-like thin films within the cement matrix, and these network-like films can bridge cracks in the cement matrix and improve the mechanical properties of the cement mortar. Over- incorporation of PVA may result in the formation of large piece polymer films that coat the cement particles, delay the hydration of the cement mortar and adversely affect its performance. The mechanical properties of the cement mortar show a significant increase and then decrease with a change in the PVA incorporation. When the PVA content was 0.6% and 1.0%, the mortar had the best compressive and flexural strengths, respectively. The compressive strength of the cement mortar increased by 12.15% for a PVA content of 0.6%, and the flexural strength of the cement mortar increased by 24.83% for a PVA content of 1.0%.

A review on acrylic based hydrogels and their applications in wastewater treatment

The acrylic based hydrogels have attracted the attention of many researchers in the field of pollutants adsorption such as dyes and metal cations due to their high swelling and adsorption capacities. This review introduces acrylic based hydrogels and focuses on their adsorption properties. We first described the methods for synthesizing hydrogels. Usual methods of characterization of acrylic based hydrogels such as swelling, adsorption capacity and desorption efficiency of the pollutants have been investigated. In addition, the adsorption isotherm and kinetic models which determine the mechanism of pollutants' adsorption by hydrogels have been introduced and relations that determine the values of thermodynamic parameters which define accomplishment of adsorption process have been investigated. In the following sections, a perfect insight has been provided on natural and synthetic acrylic based hydrogels. The effective parameters of swelling and adsorption by acrylic based hydrogels have been reviewed and the mechanism of pollutant's adsorption by acrylic based hydrogels has been discussed.

High performances of dual network PVA hydrogel modified by PVP using borax as the structure-forming accelerator

A dual network hydrogel made up of polyvinylalcohol (PVA) crosslinked by borax and polyvinylpyrrolidone (PVP) was prepared by means of freezing-thawing circles. Here PVP was incorporated by linking with PVA to form a network structure, while the introduction of borax played the role of crosslinking PVA chains to accelerate the formation of a dual network structure in PVA/PVP composite hydrogel, thus endowing the hydrogel with high mechanical properties. The effects of both PVP and borax on the hydrogels were evaluated by comparing the two systems of PVA/PVP/borax and PVA/borax hydrogels. In the former system, adding 4.0% PVP not only increased the water content and the storage modulus but also enhanced the mechanical strength of the final hydrogel. But an overdose of PVP just as more than 4.0% tended to undermine the structure of hydrogels, and thus deteriorated hydrogels’ properties because of the weakened secondary interaction between PVP and PVA. Likewise, increasing borax could promote the gel crosslinking degree, thus making gels show a decrease in water content and swelling ratio, meanwhile shrinking the pores inside the hydrogels and finally enhancing the mechanical strength of hydrogels prominently. The developed hydrogel with high performances holds great potential for applications in biomedical and industrial fields.

Novel electrodialysis cation exchange membrane prepared by 2-acrylamido-2-methylpropane sulfonic acid; heavy metal ions removal

In the present work a novel heterogeneous cation exchange membrane (CEM) composed of poly vinyl chloride (PVC) and 2-acrylamido-2-methylpropane sulfonic acid based hydrogel (AMAH) was prepared. The membranes were fabricated with different fractions of AMAH to optimize the performance in desalination. The hydrogel was characterized by FT-IR to prove the successful synthesis. The membrane properties such as permselectivity, ionic permeability, flux, water content, electrical resistance, morphology, contact angle and dimensional stability were evaluated. Modified membranes showed acceptable dimensional stabilities, more hydrophilic surface, higher water content and porosity. SEM images revealed the formation of a more porous membrane structure. Membrane permselectivity and transport number showed a relatively constant then decreasing trend in Na⁺ and Ba²⁺ solutions. The experimental results showed that the incorporation of AMAH into the PVC matrix obviously improved ionic permeability and flux of Na (∼9%) and Ba (∼23%). Membrane electrical resistance was declined about 36% by adding AMAH in the membrane structure. Membranes' performance in potassium and heavy metal ions removal showed a remarkable separation capacity of K⁺ (99.9%), Pb²⁺ (99.9%) and Ni²⁺ (96.9%). Membranes showed desirable potential for scaling removal.