Active Cellulose-Based Food Packaging and Its Use on Foodstuff

The essential role of active packaging is food quality improvement, which results in an extension of shelf life. Active packaging can also further enhance distribution from the origin point, and contributes to food waste reduction, offering greater sustainability. In this study, we introduced a new method for obtaining cellulose-based active packages, combining gamma irradiation as an eco-friendly activation process, and clove essential oil and cold-pressed rosehip seed oil as bioactive agents. Newly obtained bioactive materials were evaluated to assess their structural, hydrophobic, and morphological properties, thermal stability, and antioxidant and antimicrobial properties. The results showed that the plant oils induced their antimicrobial effects on paper, using both in vitro tests, against several bacterial strains (Gram-positive bacteria Listeria monocytogenes and Gram-negative bacteria Salmonella enteritidis and Escherichia coli), and in vivo tests, on fresh cheese curd and beef. Moreover, these oils can help control foodborne pathogens, which leads to extended shelf life.

Particleboards Bonded by an Imidazole-Based Adhesive System

Particleboards with different combinations of the adhesive material imidazole, citric acid, and sorbitol were produced. Softwood sawdust from a Swedish sawmill was mixed with an aqueous solution of the chemicals and then dried to 0% moisture content prior to pressing. The boards were pressed to a target density of 700 kg m-3 at either 200 °C or 220 °C for 10 min. The hygroscopic and mechanical properties of the boards were clearly better at 220 °C than 200 °C for all used chemical combinations. A combination of imidazole (14.4 wt%) and citric acid (11.3 wt%) led to the best results, where the thickness swelling after 24 h of water immersion was 6.3% and the internal bonding strength was 0.57 MPa. The modulus of rupture and modulus of elasticity were 3.3 MPa and 1.1 GPa, respectively. Cyclic accelerated weathering showed exceptional stability with a thickness change after boiling and drying of only 2.1% compared to the initial dry thickness. This study indicates that the presence of imidazole leads to greatly improved hygroscopic properties and good internal bonding strength when used in particleboards.

Effects of Biological and Chemical Degradation on the Properties of Scots Pine Wood-Part I: Chemical Composition and Microstructure of the Cell Wall

Research on new conservation treatment for archaeological wood requires large amounts of wooden material. For this purpose, artificial wood degradation (biological-using brown-rot fungus Coniophora puteana, and chemical-using NaOH solution) under laboratory conditions was conducted to obtain an abundance of similar samples that mimic naturally degraded wood and can serve for comparative studies. However, knowledge about its properties is necessary to use this material for further study. In this study, the chemical composition and microstructure of degraded cell walls were investigated using FT-IR, XRD, helium pycnometry and nitrogen absorption methods. The results show that biological degradation caused the loss of hemicelluloses and celluloses, including the reduction in cellulose crystallinity, and led to lignin modification, while chemical degradation mainly depleted the amount of hemicelluloses and lignin, but also affected crystalline cellulose. These changes affected the cell wall microstructure, increasing both surface area and total pore volume. However, the chemical degradation produced a greater number of mesopores of smaller size compared to fungal decomposition. Both degradation processes weakened the cell wall's mechanical strength, resulting in high shrinkage of degraded wood during air-drying. The results of the study suggest that degraded wood obtained under laboratory conditions can be a useful material for studies on new consolidants for archaeological wood.

Factors That Affect the Mechanical Strength of Archaeological Wood-A Case Study of 18th-Century Wooden Water Pipes from Bóżnicza Street in Poznań, Poland

Large amounts of archaeological wood are often excavated during groundworks in cities and towns. Part of the unearthed artefacts is usually saved, conserved and then presented in museums. However, if the finding contains several similar objects, some of them could potentially be further employed for some other practical purposes. The research aimed to determine the mechanical performance of the remains of wooden water mains excavated at Bóżnicza street in Poznań, Poland and evaluate its potential usefulness for any practical purposes. First, wood density was determined along with its mechanical strength in compression. The density of archaeological wood identified as Scots pine was lower than contemporary pinewood (383 kg × m^-3 vs. 572 kg × m^-3); therefore, its mechanical properties in compression tests were also lower, as expected, making the wood unsuitable for any practical applications. However, the differences in modulus of elasticity and compressive strength were not justified by the differences in wood density. Further infrared spectroscopy and X-ray diffraction analyses revealed additional differences in chemical composition and cellulose crystallinity between archaeological and contemporary wood. The results indicated the decrease in carbohydrate content and cellulose crystallinity in degraded wood, which, in addition to wood density, apparently contribute to the deterioration in mechanical strength of archaeological wood. The case study of the excavated archaeological wooden pipes shows that they have historical value but are not useful for practical purposes. It also revealed that not only wood density but also its chemical composition and cellulose crystallinity level has a substantial impact on the wood mechanical properties, particularly in compression.

Structural characterization and mechanical properties of wet-processed fibreboard based on chemo-thermomechanical pulp, furanic resin and cellulose nanocrystals

Fibreboards are made of lignocellulosic fibres and synthetic adhesive which connect them. These synthetic adhesives, while relatively low-cost, are usually non-biodegradable and may cause health and environmental issues. Therefore, in recent years, there has been an increased demand for replacing these adhesives with bio-derived adhesives. The present study aims to develop fibreboards from chemo-thermomechanical pulp (CTMP) and a furanic resin based on prepolymers of furfuryl alcohol via wet-processing. To improve the bonding properties, maleic acid, aluminium sulphate, and cellulose nanocrystals (CNCs) were added. The resulting fibreboards were evaluated for their structural features and mechanical properties. The bending strength was improved when CNCs were added into the fibre's suspension, and the morphology indicated a more compact structure. The combination of the CTMP with CNC and Biorez resulted in the same mechanical behaviours as those noted for CTMP alone, the best performance being observed for the boards in which Al₂(SO₄)₃ was added. Infrared spectroscopy and X-ray diffraction also proved the presence of cellulose nanocrystals and resin in the boards by increased specific bands intensity and crystallinity index, respectively.

Natural decay of archaeological oak wood versus artificial degradation processes - An FT-IR spectroscopy and X-ray diffraction study

Wood has been extensively used as a material for different applications over the years, therefore the understanding of different degradation processes in various environments is of great importance. In this study, the infrared spectroscopy, X-ray diffraction and chemometric methods were used to evaluate and compare the structure of archaeological and artificially degraded oak wood. The results clearly show that modifications in the structure of archaeological wood are related to the position of the material in the log (sapwood and heartwood), thus the extent of wood degradation. To identify the possible factors influencing these effects, the control wood samples were exposed to artificial white rot biodegradation with Coriolus (Trametes) versicolor and to alkali treatment (with NaOH solution). Due to the structural similarities between biodegraded wood and control or archaeological samples, this type of decay is likely to occur during natural ageing along with degradation produced by other environmental factors. Further, no real similarity was identified between the alkali treated wood and archaeological samples, indicating that such degradation does not affect wood under natural conditions.

Structural changes of wood during hydro-thermal and thermal treatments evaluated through NIR spectroscopy and principal component analysis

Spruce wood samples were subjected to different conditions of thermal and hydro-thermal treatment by varying the temperature, relative humidity and period of exposure. The obtained treated samples were evaluated using near infrared spectroscopy (NIR), principal component analysis (PCA) and hierarchical cluster analysis (HCA) in order to evidence the structural changes which may occur during the applied treatment conditions. Following this, modification in all wood components were observed, modifications which were dependent on the temperature, amount of relative humidity and also the treatment time. Therefore, higher variations were evidenced for samples treated at higher temperatures and for longer periods. At the same time, the increase in the amount of water vapours in the medium induced a reduced rate of side chains and condensation reactions occurring in the wood structure. Further, by PCA and HCA was possible to discriminate the modifications in the wood samples according to treatment time and amount of relative humidity.

A near infrared spectroscopic study of the structural modifications of lime (Tilia cordata Mill.) wood during hydro-thermal treatment

The modifications and/or degradation of lime (Tillia cordata) wood components during wood heat treatment under low temperature at about 140°C and 10% percentage of relative humidity were evaluated. The aim of this study was to obtain results by simple NIR coupled with second derivative, principal component analysis and two dimensional correlation spectroscopy in order to better understand how these techniques are able to evaluate structural differences resulted under hydro-thermal treatment of the wood over a period of 504h. The NIR spectra of treated samples were compared with the reference one. Due to the broad bands in the NIR spectra, the assignment and modifications occurring during treatment is difficult, therefore the second derivative principal component analysis were applied. Principal component analysis by first two components was able to differentiate the samples series, PC1 being considered as the time axis, and PC2 as the axis representing the structural modification of wood components. 2D NIR correlation spectroscopy was able to estimate the sequential order of the groups variations under the hydro-thermal treatment time as external perturbation, indicating as first moment changes the OH and CO groups from carbohydrates and lignin, followed by CarH, CH and CH2 groups from lignin, cellulose and hemicelluloses.

Structural study of photodegraded acrylic-coated lime wood using Fourier transform infrared and two-dimensional infrared correlation spectroscopy

The weathering of acrylic films and acrylic-coated lime wood (Tillia cordata Mill.) were examined using Fourier transform infrared (FT-IR) and two-dimensional infrared correlation spectroscopy. The obtained results showed chemical changes induced by exposure to weathering conditions, in both films and coated wood. The observed spectral changes of the acrylic films refer to the absorption band assigned to the C-O stretching, which progressively decreases with increasing exposure time. In the spectra of treated wood samples the main signal indicating the advance of oxidation during the photodegradation exposure is the gradual increase and broadening of the band in the carbonyl region. This is due to the formation of the non-hydrogen bonded aliphatic carboxylic acids and γ-lactone structures in the acrylic resin and of the nonconjugated ketones, carboxyl groups, and lactones in wood. As a consequence, the increase of the 1734 cm(-1) band is due to the degradation of lignin from wood surface. These observations are also supported by the decreased intensities of the bands at 1598 and 1505 cm(-1), assigned to C=C of aromatic skeletal (lignin). The relative intensity of the characteristic aromatic lignin band at 1505 cm(-1) decreases up to 25% of its original value after weathering, being less than half of the value obtained for uncoated wood. Two-dimensional infrared (2D IR) correlation spectroscopy was used to identify the sequence of the modifications of the different stretching vibrations bands under the weathering conditions, the method allowing the prediction of the order of degradation reactions. The acrylic resin degradation starts with the formation of radicals by abstraction of the tertiary hydrogen atoms of the methyl acrylate units and the α-CH3 groups from the ethyl methacrylate units. The subsequent decomposition and oxidation led to the formation of alcohol groups, hydroperoxides, ketones, and/or carboxylic acid groups. The 2D IR correlation spectra of weathered impregnated wood also revealed the elimination of low molecular weight compounds following the degradation of lignin and carbohydrates components from wood.

Structural analysis of photodegraded lime wood by means of FT-IR and 2D IR correlation spectroscopy

In this study the weathering behavior of lime wood (Tillia cordata Mill.) has been examined using FT-IR and 2D IR correlation spectroscopy, which evidenced chemical changes induced by exposure to weathering conditions. It was showed that lignin is most sensitive component to the photodegradation processes as indicated by considerable decreases in the intensities of the characteristic aromatic lignin band at 1505cm(-1) and other associated bands. By 2D correlation spectroscopy has been demonstrated that the moment of CO from carboxyl and acetyl groups in hemicelluloses is changing first, followed by the CC of aromatic skeletal, CO in non-conjugated ketones, carboxyl groups and lactones, absorbed O-H and conjugated C-O groups in quinones. The carbonyl formation corresponded well with lignin degradation, indicating a close relationship between them. Comparing the rate of carbonyl formation and lignin decay clearly showed that the former is remarkably higher than the latter, indicating the formation of carbonyl bands at 1738cm(-1) probably resulted from not only lignin oxidation but also from reactions occurring in other components of the wood. Quinine formation is combined with the decay of aromatic structures and the formation of conjugated carbonyl groups.

Characterization of fungal-degraded lime wood by X-ray diffraction and cross-polarization magic-angle-spinning 13C-nuclear magnetic resonance spectroscopy

X-ray diffraction, scanning electron microscopy (SEM), and solid-state cross-polarization magic-angle-spinning (CP/MAS) (13)C-NMR spectroscopy were applied to determine changes over time in the morphology and crystallinity of lime wood (Tilia cordata Miller) generated by the soft-rot fungi. Wood samples were inoculated with Trichoderma viride Pers for various durations up to 84 days. Structural and morphological modifications were assessed by comparing the structural features of decayed lime wood samples with references. Significant morphology changes such as defibration or small cavities were clearly observed on the SEM micrographs of lime wood samples exposed to fungi. Following the deconvolution process of the diffraction patterns, the degree of crystallinity, apparent lateral crystallite size, the proportion of crystallite interior chains, and the cellulose fraction have been determined. It was found that all crystallographic data vary with the duration of exposure to fungi. The degree of crystallinity and cellulose fraction tend to decrease, whereas the apparent lateral crystallite size and the proportion of crystallite interior chains increase with prolonged biodegradation processes. The most relevant signals in CP/MAS (13)C-NMR spectra were assigned according to literature data. The differences observed were discussed in terms of lignin and cellulose composition: by fixing the lignin reference signal intensity, the cellulose and hemicelluloses moieties showed a relative decrease compared to the lignin signals in decayed wood.

Spectral characterization of eucalyptus wood

The main difficulties in wood and pulp analyses arise principally from their numerous components with different chemical structures. Therefore, the basic problem in a specific analytical procedure may be the selective separation of the main carbohydrate-derived components from lignin due to their chemical association and structural coexistence. The processing of the wood determines some structural modification in its components depending on the type of wood and the applied procedure. Fourier transform infrared (FT-IR) spectrometry and X-ray diffraction have been applied to analyze Eucalyptus g. wood chips and unbleached and chlorite-bleached pulp. The differences between samples have been established by examination of the spectra of the fractions obtained by successive extraction (acetone extractives, acetone free extractive samples, hemicelluloses, and lignins) by evaluating the derivative spectra, band deconvolution, etc. The energy and the hydrogen bonding distance have been evaluated. The relationship between spectral characteristics and sample composition has been established, as well as the variation of the degree of crystallinity after pulping and bleaching. The integral absorption and lignin/carbohydrate ratios calculated from FT-IR spectra of the IR bands assigned to different bending or stretching in lignin groups are stronger in the spectrum of eucalyptus chips than those from brown stock (BS) pulp spectra because of the smaller total amount of lignin in the latter. FT-IR spectra clearly show that after chlorite bleaching the structure of the wood components is partially modified or removed. Along with FT-IR data, the X-ray results confirmed the low content of lignin in the pulp samples by increasing the calculated values of the crystalline parameters. It was concluded that FT-IR spectroscopy can be used as a quick method to differentiate Eucalyptus globulus samples.

The prevalence of skin conditions in Romanian school children

Virtually nothing is known about the prevalence of skin conditions in children in the general population. Although we know something about the relative frequency of skin conditions seen by dermatologists, we do not know how such referrals are influenced by factors such as social class, accessibility to medical services or educational and cultural background. In order to estimate the burden and relative frequency of dermatological disease in children in the community, we measured the point prevalence of skin conditions in 1114 Romanian schoolchildren aged 6-12 years, using the British Association of Dermatologists diagnostic index. The overall point prevalence of children with one or more skin diseases was 22.8%, with no significant differences according to age group or sex, except for pityriasis alba which showed a male predominance (P = 0. 007). The most common diseases were infectious dermatoses such as viral warts and insect bites (6.3%), dermatitis/eczema (5.1%), pityriasis alba (5.1%), keratosis pilaris (4.0%) and urticaria (1. 9%). Together, these five groups accounted for more than 84% of the cases. Of the 1114 children, 213 (19.1%) had only one skin disease and 41 (3.7%) had two skin diseases. While acknowledging the limitations in defining which skin conditions can benefit from medical care, this study suggests that skin disorders are common in Romanian schoolchildren, affecting about one-quarter of 6-12 year olds. Such a point prevalence is likely to be conservative because of the tendency of prevalence estimates to exclude many other dermatoses of short duration. The finding that over 80% of the disorders can be grouped into fewer than six categories is important in informing training programmes and delivery of service for primary health care teams. This study provides a baseline for further studies into the morbidity and use of health care services by children with skin disease in the community.

Community validation of the United Kingdom diagnostic criteria for atopic dermatitis in Romanian schoolchildren

Although the U.K. modification of Hanifin and Rajka's diagnostic criteria for atopic dermatitis (AD) for use in epidemiological studies has demonstrated good validity and repeatability when previously tested in a U.K. community setting, little is known about its performance in other countries where different cultural, educational and linguistic factors could impair validity. We used a questionnaire to test the validity of the U.K. criteria as a point prevalence measure of AD in 1114 Romanian schoolchildren aged 6-12 years against the clinical diagnosis of a dermatologist with an interest in AD, who was unaware of the questionnaire content and responses. The sensitivity and specificity of the U.K. criteria for AD in this setting was 74% and 99%, respectively, an improvement rather than a deterioration in validity when compared with the previous U.K. study. Test-retest repeatability for all of the questions pertaining to the U.K. criteria using the chance-corrected kappa statistic was high, with values of 0.72 and over. The positive predictive value of the criteria was lower than in the U.K. study (63% compared with 80%, respectively) due to the very low prevalence of AD in this study (2.4%). The validity of a parental report of 'eczema' was poor, with a sensitivity of 22%, specificity of 97% and positive predictive value of 18%. This study suggests that the U.K. criteria perform well in settings outside the U.K., although care has to be taken when using the criteria to ascertain cases in settings where the prevalence of AD is very low.

Experimental use of prostaglandin E2 (Dinoprost) in the treatment of duodenal ulcer in humans

Oral administration of 20 mg PGE2/day/patient (5 mg every 4 hours, 4 times a day) promptly relieved pain in 10 patients suffering from duodenal ulcer. After 3 days of treatment, the ulceration--observed by radiologic and gastrofibroscopic means--diminished by 30% in dimensions, and after 10 days, it almost disappeared. The results were compared with those observed in a placebo-group, who received 20 mg lactose/day/patient and with those in another group treated by sodium bicarbonate.

The role of prostaglandins in the development of malignant melanoma in hamsters

A deficiency of prostaglandins (especially of group E) could be an important factor in the genesis and evolution of malignant melanoma. Compensation for such a deficit would be a logical way of medically treating this tumour. In order to test this hypothesis two groups of hamsters bearing malignant melanomas were used. The first group was treated locally with PGE2 while the other group received control injections. After 12 days tumour growth in the PG test group was sharply reduced in comparison with the controls. Tumour growth resumed when PG treatment was stopped.