Functional Plasticity of Foraging Shelter Tubes Built by Termites

Social insects' constructions are diverse and functionally flexible. We aimed to understand how termites modify their behavior and building material to change the function of a shelter tube. Construction behaviors of three termite species, Coptotermes formosanus Shiraki (Blattodea: Rhinotermitidae), Odontotermes formosanus (Shiraki) (Blattodea: Termitidae), and Nasutitermes takasagoensis (Nawa) (Blattodea: Termitidae), were recorded and analyzed. We measured the thickness and organic matter content of shelter tubes, and further tested their water loss and water drop resistance. All three termite species used a cement-brick construction procedure. The shelter tubes of C. formosanus and N. takasagoensis incorporating of woody material and feces present a strong resistance to water drops. Shelter tubes of the fungus-growing termite, O. formosanus, constructed using only soil and fluid secretion had a weak resistance to water drops. The trade-off between using feces to increase hydrophobicity of shelter tubes and using feces to grow fungus likely occurs in fungus-growing termites. Among intraspecific colonies, increasing the thickness of shelter tube improved resistance to water loss and water drops. This study demonstrated termites employed limited construction material and building behaviors to achieve functional plasticity of foraging shelter.

Determination of glyphosate, aminomethylphosphonic acid, and glufosinate in river water and sediments using microwave-assisted rapid derivatization and LC-MS/MS

Glyphosate (N-phosphonomethyl glycine) and glufosinate (ammonium dl-homoalanin- 4-methyl phosphinate) are nonselective, broad-spectrum, and highly polar herbicides that are wildly used for weed control in aquatic systems and vegetation control in non-crop areas. Aminomethylphosphonic acid (AMPA) is the major degradation product of glyphosate. To address the concerns to its environmental residue and the possible adverse effects, the analytical methods by using microwave-assisted derivatization were developed for determining glyphosate, AMPA, and glufosinate in river water and sediments. The methods applied the 9-fluorenylmethyloxycarbonyl chloride (FMOC-Cl) derivatization for the analytes. The microwave heating is first-time applied to reduce the FMOC-reaction time of glyphosate, AMPA, and glyphosate in the environmental samples to less than 2.5 min. The microwave-assisted methods were successfully validated for river water and sediment. The linear ranges of 7.8-2000.0 ng/L and 0.78-100.0 ng/g were achieved by using 10 mL of water and 2 g of sediments. Glyphosate was found in 30/32% and 25/32% of 32 water and 32 sediments at 27.1-1353.9 ng/L and 2.4-189.6 ng/g levels. AMPA was found in 30/32% and 30/32% of 32 water and 32 sediments at 60.2-1509.0 ng/L and 1.8-233.6 ng/g levels. Glyphosate was found in 10/32% of 32 water at 14.8-503.1 ng/L levels. No glufosinate residue was observed for 32 sediments. The residues of glyphosate and AMPA were wildly detected in the river waters and sediments near the agricultural regions, and glufosinate was less detected. This is the first study that reported herbicide levels in water and sediment from Taiwan rural areas using microwave-assisted rapid derivatization, useful information for environmental management.

Life cycle assessment of heavy metal contaminated sites: phytoremediation and soil excavation

Phytoextraction by native Taiwanese chenopod (Chenopodium formosanum Koidz.) and Napier grass (Pennisetum purpureum) for heavy metals such as chromium (Cr), nickel (Ni), and copper (Cu) was reported first. Maximum bioconcentration factors of Cu and Cr were 8.8 and 12.5 by Taiwanese chenopod. Napier grass cultivar Taishi No.4 plants demonstrated higher survivals than that of Taiwanese chenopod, under heavy metal stress in soils. All heavy metal accumulation and biomass data were employed, as well as historical engineering data were collected for conventional excavation-and-refill remediation of two sites. Life cycle assessment (LCA) was conducted for comparing environmental performances of phytoextraction and conventional remediation for two contaminated sites. Assuming one-year growth, three harvests were done and biomass was collected and sent to the nearest municipal incinerators, phytoextraction by both plants demonstrated superior environmental performances than conventional methods for contaminated site remediation. High quantities of fuels to haul the soils of conventional methods mainly contributed to the greenhouse gas emission. Phytoextraction has the most advantages for sites with lesser extents of pollution and time restraints. Environmental performances of phytoremediation were even better if energy recovered from biomass incineration is counted. Novelty statement Phytoextraction by native Taiwanese chenopod and Napier grass was firstly reported. Life cycle assessment was conducted for comparing the phytoextraction and conventional remediation. Phytoextraction demonstrated superior environmental performances. Energy reutilization of biomass recovered made phytoremediation more sustainable.

Enhancement of phytoextraction by Taiwanese chenopod and Napier grass by soapnut saponin and EDDS additions

Employment of biosurfactants and biodegradable chelants could further promote sustainability of soil and groundwater remediation tasks. Biosurfactant (soapnut saponin) and biodegrading chelants (ethylenediamine-N,N'-disuccinic acid (EDDS)) were employed to enhance the phytoextraction by native Taiwanese chenopod (Chenopodium formosanum Koidz.), Napier grass (Pennisetum purpureum) cultivar Taishi No. 4, and soapwort (Saponaria officinalis). Ethylene diamine tetraacetic acid (EDTA) was also employed as the control. Contaminated soils as silty clay loam texture was collected from a defunct rice paddy, containing chromium (Cr), cadium (Cd), and copper (Cu). Addition of both soapnut saponin and EDDS proportionally increased bioaccumulation factors (BCFs) of aboveground biomass for all three plants. Taiwanese chenopod demonstrated the best BCF values among three plants, with BCF increased from 0.76 to 2.6 and 1.3 for Cu under the presence of the highest dosages of EDDS and saponin. Plant aboveground biomass did exhibit negative correlation toward biomass metal concentrations. Presence of saponin did exhibit the least negative slopes among the correlations of all three additives for three plants. Taiwanese chenopod did exhibit the least negative slopes among the correlations of all three additives for three plants. Above observations suggested that saponin may have some protection for plants, especially for Napier grass. Taiwanese chenopod could possess more tolerance toward heavy metals than Napier grass does.

Effect of Paenibacillus cellulase pretreatment for fiber surface

Refining is the major process of paper formation. This study focuses on the impact of a specific enzyme (Paenibacillus cellulase) for fibers on the surfaces, the roughness and height of the fibers are also investigated. Effects of enzyme dosages and the mechanical refining action (PFI revolution) on fiber physical properties were also analyzed. The fibers were observed by scanning electron microscopy (SEM), their roughness and height were analyzed by Atomic force microscopy (AFM). Results show that the Paenibacillus cellulase pretreatment increased the drainability of both kinds of pulp at the same level of refining energy. In other words, enzymatic treatment on pulp refining consumed less refining revolutions to reach the same drainability compared to the untreated pulp. Although the viscosity of both kinds of pulp was degraded with the enzymatic treatment, the physical properties of paper had no significantly negative influence on them. The results indicated the treatment with cellulase swelled the fibers in the absence of refining, and there were better fibrillation on the fibers treated with cellulase after refining. Furthermore, the statistical analysis of AFM suggested that both kinds of pulp treated with low cellulase dosage with PFI refining had higher roughness.

Agricultural waste derived fuel from oil meal and waste cooking oil

Oil meal is a by-product of the oil industry (peanut meal, sesame meal, and camellia meal). Oil is extracted from seeds, and the leftover meal is then pelletized, and this process generates a large amount of waste oil meal in Taiwan. In this study, peanut meal, sesame meal, and camellia meal derived fuels were prepared from the waste oil meal with waste cooking oil. The combustion behaviors of the oil meal derived fuels were also investigated. The characteristics of the derived fuel made from oil meal with waste cooking oil showed that the ash content is less than 10% and its calorific value reached 5000 kcal/kg. Additionally, the activation energy of the oil meal and waste cooking oil was analyzed by the Kissinger method. The results show that the fuel prepared in this work from the oil meal mixed with waste cooking oil is suitable for use as an alternative fuel and also avoids food safety issues.

Bioethanol production from recovered napier grass with heavy metals

Using plants to absorb and accumulate heavy metals from polluted soil, followed by the recycling of explants containing heavy metals, can help achieve the goal of reverting contaminated soil to low heavy-metal content soil. However, the re-use of recovered explants can also be problematic. Meanwhile, bioethanol has become a popular energy source. In this study, napier grass was used for the remediation of soil contaminated with heavy metals (artificially contaminated soil). The influence of bioethanol production from napier grass after phytoremediation was also investigated. The concentration of Zn, Cd, and Cr in the contaminated soil was 1000, 100, and 250 mg/kg, respectively. After napier grass phytoremediation, the concentration (dry biomass) of Zn, Cd, and Cr in the explants was 2701.97 ± 173.49, 6.1 ± 2.3, and 74.24 ± 1.42 mg/kg, respectively. Biomass production in the unpolluted soil was 861.13 ± 4.23 g. The biomass production ratio in high Zn-polluted soil was only 3.89%, while it was 4.68% for Cd and 21.4% for Cr. The biomass obtained after napier grass phytoremediation was pretreated using the steam explosion conditions of 180 °C, for 10 min, with 1.5% H₂SO₂, followed by enzymatic hydrolysis. The efficiency of enzymatic hydrolysis for Zn-polluted biomass was 90% of the unpolluted biomass, while it was 77% for Cd, and approximately the same for Cr. The fermentation efficiency of the heavy-metal-containing biomass was higher than the control biomass. The fermentation ethanol concentration obtained was 8.69-12.68, 13.03-15.50, and 18.48-19.31 g/L in Zn, Cd, and Cr environments, respectively. Results show that the heavy metals had a positive effect on bacteria fermentation. However, the fermentation efficiency was lower for biomass with severe heavy metal pollution. Thus, the utilization of napier grass phytoremediation for bioethanol production has a positive effect on the sustainability of environmental resources.

Upregulation of Haploinsufficient Gene Expression in the Brain by Targeting a Long Non-coding RNA Improves Seizure Phenotype in a Model of Dravet Syndrome

Dravet syndrome is a devastating genetic brain disorder caused by heterozygous loss-of-function mutation in the voltage-gated sodium channel gene SCN1A. There are currently no treatments, but the upregulation of SCN1A healthy allele represents an appealing therapeutic strategy. In this study we identified a novel, evolutionary conserved mechanism controlling the expression of SCN1A that is mediated by an antisense non-coding RNA (SCN1ANAT). Using oligonucleotide-based compounds (AntagoNATs) targeting SCN1ANAT we were able to induce specific upregulation of SCN1A both in vitro and in vivo, in the brain of Dravet knock-in mouse model and a non-human primate. AntagoNAT-mediated upregulation of Scn1a in postnatal Dravet mice led to significant improvements in seizure phenotype and excitability of hippocampal interneurons. These results further elucidate the pathophysiology of Dravet syndrome and outline a possible new approach for the treatment of this and other genetic disorders with similar etiology.

Phytoremediation of heavy metal contaminated soil by Jatropha curcas

This study employed Jatropha curcas (bioenergy crop plant) to assist in the removal of heavy metals from contaminated field soils. Analyses were conducted on the concentrations of the individual metals in the soil and in the plants, and their differences over the growth periods of the plants were determined. The calculation of plant biomass after 2 years yielded the total amount of each metal that was removed from the soil. In terms of the absorption of heavy metal contaminants by the roots and their transfer to aerial plant parts, Cd, Ni, and Zn exhibited the greatest ease of absorption, whereas Cu, Cr, and Pb interacted strongly with the root cells and remained in the roots of the plants. J. curcas showed the best absorption capability for Cd, Cr, Ni, and Zn. This study pioneered the concept of combining both bioremediation and afforestation by J. curcas, demonstrated at a field scale.

Extraction of heavy metals from contaminated soil by Cinnamomum camphora

83 acres of rice paddy fields in Taoyuan county, Taiwan, were polluted by cadmium (Cd), chromium (Cr) and copper (Cu) through a nearby irrigation channel, and rice plantation was ceased in 1987. Camphor trees (Cinnamomum camphora) have been planted in 2 acre of the above fields since 1991. Heavy metal accumulation of roots, leaves, branches and heartwood of camphor trees were analyzed during 20-year afforestation. Averaged Cd contents of the roots were found larger than the ones of the branches, leaves, sapwood and heartwood of camphor trees growing in three polluted plots. Averaged diameters at breast height (DBH) of the planted camphor trees were 13-15 cm. Cd pollution did not significantly impact the growth of camphor trees, as similar DBH's were found from both polluted and control sites. Annual growths of DBH were from 0.63 to 0.77 cm year(-1). Planting camphor trees sequestered 68.8 ton biomass per acre. During 20-year period, 0.69-1.98 ton C year(-1) ha(-1) were sequestered on three polluted plots. The above numbers exceeded IPCC LULUCF reference values 0.31-0.53 ton C year(-1) ha(-1) for activities at forest lands.

Reduction behavior of zinc ferrite in EAF-dust recycling with CO gas as a reducing agent

EAF-dust containing metal oxides can be regarded as an important source for zinc and iron. In this study, the reduction behavior of zinc ferrite with CO gas as a reducing agent under different temperatures was investigated to develop a new process for the recovery of zinc and iron from EAF-dust. The results of the phase studies with synthetic franklinite show that zinc substituted wustite, and spinel with low zinc content formed at lower temperatures from 450 to 850 °C due to incomplete zinc-iron-separation. Zinc ferrite was completely reduced to metallic zinc and iron at 950 °C. After evaporation and condensation, metallic zinc was collected in the form of zinc powder while iron, the reduction residue, was obtained in the form of direct reduced iron (DRI). The mass balance indicates a high zinc recovery ratio of over 99%. The new treatment process by thermal reduction with CO gas as a reducing agent achieved higher recovery and metallization grade of both zinc and iron from EAF-dust at lower temperatures than other commercial processes. The metallic products can be used directly as semi-products or as raw materials for refinery.

Selective leaching process for the recovery of copper and zinc oxide from copper-containing dust

The purpose of this study was to develop a resource recovery procedure for recovering copper and zinc from dust produced by copper smelting furnaces during the manufacturing of copper-alloy wires. The concentrations of copper in copper-containing dust do not meet the regulation standards defined by the Taiwan Environmental Protection Administration; therefore, such waste is classified as hazardous. In this study, the percentages of zinc and copper in the dust samples were approximately 38.4% and 2.6%, respectively. To reduce environmental damage and recover metal resources for industrial reuse, acid leaching was used to recover metals from these inorganic wastes. In the first stage, 2 N of sulphuric acid was used to leach the dust, with pH values controlled at 2.0-3.0, and a solid-to-liquid ratio of 1:10. The results indicated that zinc extraction efficiency was higher than 95%. A selective acid leaching process was then used to recover the copper content of the residue after filtration. In the second stage, an additional 1 N of sulphuric acid was added to the suspension in the selective leaching process, and the pH value was controlled at 1.5-2.0. The reagent sodium hydroxide (2 N) was used as leachate at a pH greater than 7. A zinc hydroxide compound formed during the process and was recovered after drying. The yields for zinc and copper were 86.9-93.5% and 97.0-98.9%, respectively.

Resource recovery of organic sludge as refuse derived fuel by fry-drying process

The organic sludge and waste oil were collected from the industries of thin film transistor liquid crystal display and the recycled cooking oil. The mixing ratio of waste cooking oil and organic sludge, fry-drying temperatures, fry-drying time, and the characteristics of the organic sludge pellet grain were investigated. After the fry-drying process, the moisture content of the organic sludge pellet grain was lower than 5% within 25 min and waste cooking oil was absorbed on the dry solid. The fry-drying organic sludge pellet grain was easy to handle and odor free. Additionally, it had a higher calorific value than the derived fuel standards and could be processed into organic sludge derived fuels. Thus, the granulation and fry-drying processes of organic sludge with waste cooking oil not only improves the calorific value of organic sludge and becomes more valuable for energy recovery, but also achieves waste material disposal and cost reduction.

Factors affecting chelating extraction of Cr, Cu, and As from CCA-treated wood

The disposal of chromated copper arsenate (CCA)-treated waste wood is becoming a serious problem in many countries due to potential leaching of hazardous elements from in-service use in the environment or disposal of solutions after remediation; therefore, it is necessary to develop proper remediation techniques. The effects of concentration, extraction period, temperature, and sequential extraction on the extraction of Cr, Cu, and As from CCA-treated wood using [S,S]-ethylenediaminedisuccinic acid (EDDS), ethylenediaminetetraacetic acid (EDTA), and nitrilotriacetic acid (NTA) were studied. Mobility of metal in the samples was evaluated by using a sequential extraction scheme that could give the information needed to explain different extraction efficiencies for different metals. Results of long-term leaching tests of CCA-treated wood before and after EDDS extraction were used to evaluate Cr, Cu, and As leachability. Kinetic experiments showed that 6 h was the optimum extraction time for all metals and CCA-treated wood. Experimental results showed that EDDS is a very effective chelating agent for the extraction of Cr, Cu, and As from CCA-treated wood. Increased temperature significantly enhanced the extraction efficiency of CCA metals, especially Cr and As. The much better extractability of Cu compared to Cr and As by chelating agents can be attributed to the presence of larger weakly bound fractions. The CCA-treated woods after EDDS extraction have met the EPA's TCLP regulatory limit and could be classified as a non-hazardous waste according to identification standard of hazardous wastes.

Can iterative reconstruction improve imaging quality for lower radiation CT perfusion? Initial experience

BACKGROUND AND PURPOSE

Initial results using IR for CT of the head showed satisfactory subjective and objective imaging quality with a 20-40% radiation dose reduction. The aim of our study was to compare the influence of IR and FBP algorithms on perfusion parameters at standard and lowered doses of CTP.

MATERIALS AND METHODS

Forty patients with unilateral carotid stenosis post-carotid stent placement referred for follow-up CTP were divided into 2 groups (tube currents were 100 mAs in group A and 80 mAs in group B). Datasets were reconstructed with IR and FBP algorithms; and SNRs of gray matter, white matter, and arterial and venous ROIs were compared. CBF, CBV, and MTT means and SNRs were evaluated by using linear regression, and qualitative imaging scores were compared across the 2 algorithms.

RESULTS

The mean effective radiation dose of group B (2.06 mSv) was approximately 20% lower than that of group A (2.56 mSv). SNRs for ROIs in the dynamic contrast-enhanced images were significantly higher than those for the FBP images. Correlations of the SNRs for CBF, CBV, and MTT across the 2 algorithms were moderate (R² = 0.46, 0.23, and 0.44, respectively). ROIs in gray matter rather than the IR algorithm predicted increasing SNRs in all CBF, CBV, and MTT maps. Two cases of significant restenosis were confirmed in both algorithms. CBV, CBF, and MTT imaging scores did not differ significantly across algorithms or groups.

CONCLUSIONS

Lower dose CTP (20% below normal dose) without IR can effectively identify oligemic tissue in poststenting follow-up. IR does not alter the absolute values or increase the SNRs of perfusion parameters. Other methods should be attempted to improve SNRs in settings with low tube currents.

Tracking of arsenics during the thermal stabilization of an AsH3 scrubber sludge

Toxic arsenics in an AsH(3) scrubber sludge were thermally stabilized in the temperature range of 973-1,373 K. To better understand how the high-temperature treatments can stabilize arsenics in the sludge, their synchrotron X-ray absorption near edge structure (XANES) and extended X-ray absorption fine structure (EXAFS) spectra of arsenics were determined. It is found that the reduced arsenic leachability may be associated with the formation of As(2)O(5) (51-59%) and embedded As(V) within the Ca(3)(PO(4))(2) matrix (41-49%) in the stabilized sludge. In addition, the As-O bond distances in the stabilized As(2)O(5) are much less than that of normal As(2)O(5) by 0.05-0.07 Å. The shorter As-O bond distances accompanied with the higher bonding energy also have a contribution to the thermal stabilization of arsenics.

Removal of chloride from MSWI fly ash

The high levels of alkali chloride and soluble metal salts present in MSWI fly ash is worth noting for their impact on the environment. In addition, the recycling or reuse of fly ash has become an issue because of limited landfill space. The chloride content in fly ash limits its application as basis for construction materials. Water-soluble chlorides such as potassium chloride (KCl), sodium chloride (NaCl), and calcium chloride hydrate (CaCl(2) · 2H(2)O) in fly ash are easily washed away. However, calcium chloride hydroxide (Ca(OH)Cl) might not be easy to leach away at room temperature. The roasting and washing-flushing processes were applied to remove chloride content in this study. Additionally, air and CO(2) were introduced into the washing process to neutralize the hazardous nature of chlorides. In comparison with the water flushing process, the roasting process is more efficient in reducing the process of solid-liquid separation and drying for the reuse of Cl-removed fly ash particles. In several roasting experiments, the removal of chloride content from fly ash at 1050°C for 3h showed the best results (83% chloride removal efficiency). At a solid to liquid ratio of 1:10 the water-flushing process can almost totally remove water-soluble chloride (97% chloride removal efficiency). Analyses of mineralogical change also prove the efficiency of the fly ash roasting and washing mechanisms for chloride removal.

Utilization of spent activated carbon to enhance the combustion efficiency of organic sludge derived fuel

This study examines the heating value and combustion efficiency of organic sludge derived fuel, spent activated carbon derived fuel, and derived fuel from a mixture of organic sludge and spent activated carbon. Spent activated carbon was sampled from an air pollution control device of an incinerator and characterized by XRD, XRF, TG/DTA, and SEM. The spent activated carbon was washed with deionized water and solvent (1N sulfuric acid) and then processed by the organic sludge derived fuel manufacturing process. After washing, the salt (chloride) and sulfide content could be reduced to 99% and 97%, respectively; in addition the carbon content and heating value were increased. Different ratios of spent activated carbon have been applied to the organic sludge derived fuel to reduce the NO(x) emission of the combustion.

Monitoring peri-therapeutic cerebral circulation time: a feasibility study using color-coded quantitative DSA in patients with steno-occlusive arterial disease

BACKGROUND AND PURPOSE

Intracranial hemodynamics are important for management of SOAD. This study aimed to monitor peri-stent placement intracranial CirT of patients with SOAD.

MATERIALS AND METHODS

Twenty-five patients received stent placement for extracranial ICA stenosis, and 34 patients with normal CirT were recruited as controls. Their color-coded DSAs were used to define the Tmax of selected intravascular ROI. A total of 20 ROIs of the ICA, OphA, ACA, MCA, FV, PV, OV, SSS, SS, IJV, and MCV were selected. rTmax was defined as the Tmax at the selected region of interest minus Tmax at the cervical segment of the ICA (I1 on AP view and IA on lateral view). rTmax of the PV was defined as intracranial CirT. Intergroup and intragroup longitudinal comparisons of rTmax were performed.

RESULTS

rTmax values of the normal cohorts were as follows: ICA-AP, 0.12; ICA-LAT, 0.10; A1, 0.28; A2, 0.53; A3, 0.81; M1, 0.40; M2, 0.80; M3, 0.95; OphA, 0.35; FV, 4.83; PV, 5.11; OV, 5.17; SSS, 6.16; SS, 6.51; IJV, 6.81; and MCV, 3.86 seconds. Before stent placement, the rTmax values of arterial ROIs, except A3 and M3, were prolonged compared with values from control subjects (P < .05). None of the rTmax of any venous ROIs in the stenotic group was prolonged with significance. After stent placement, the rTmax of all arterial ROIs shortened significantly, except A1and M3. Poststenting rTmax was not different from the control group.

CONCLUSIONS

Without extra contrast medium and radiation dosages, color-coded quantitative DSA enables real-time monitoring of peri-therapeutic intracranial CirT in patients with SOAD .

Removal of chloride from electric arc furnace dust

Electric arc furnace (EAF) dust with high chloride content increases the threat of dioxin emissions and the high chloride content reduces the value of recycled zinc oxide produced by EAF dust recycling plants. This study conducts a number of laboratory experiments to determine the technical feasibility of a new dechlorination method. These methods consist of a series of roasting processes and water washing processes. In the roasting process, EAF dust was heated in a tube furnace to evaluate the parameters of atmospheric conditions, roasting temperature, and roasting time. Results indicate that sulfation roasting is more efficient in reducing chloride content than other roasting processes. The water washing process can totally remove water-soluble chloride at a solid to liquid ratio of 1:10. However, the remaining water-insoluble substance is difficult to dechlorinate. For example, lead chloride forms a hydroxyl-halide (PbOHCl) and lead chloride carbonate (Pb(2)CO(3)Cl(2)) agglutinative matrix that is hard to wash away.

The correlations between system treatment efficiencies and aboveground emergent macrophyte nutrient removal for the Hsin-Hai Bridge phase II constructed wetland

This study investigated the correlations between the system treatment efficiencies and total nitrogen (TN) and total phosphorus (TP) accumulations of aboveground tissues of the wetland macrophytes of Hsin-Hai Bridge phase II constructed wetland. Among 19 emergent macrophytes studied, the optimal TN contents, 3.82% and 3.52% (w/w) were found for water spinach (Ipomoea aquatica) and Ludwigia x taiwanensis; while the optimal TP contents were found for the above two macrophytes at 0.64% and 0.83% (w/w). The accumulations of total plant TN and TP uptakes increased from 213 to 403 kg and 41 to 75 kg from March 2007 to the peak at September 2007, respectively. The TN ratios between plant tissue accumulations and the removals from the influents were 1.57%, 2.76%, 1.51% and 3.2% from March 2007 to March 2008. In the same period, the TP ratios between plant tissue accumulations and the removals from influents were 1.71%, 8.0%, 0.58% and 10.1%. The roles of the uptakes by aboveground portions of emergent macrophytes in system nutrient removals from the influents were more significant during growth seasons.

The characteristics of organic sludge/sawdust derived fuel

A fundamental study of the characteristics of a sludge refuse-derived fuel (RDF) and the combustion behaviors were done. The test data demonstrate good results for the development of energy recovery technology of organic sludge or waste. The ash deposit formation propensity has been based on pretreatment, temperature and the ratio of organic sludge to sawdust. The usage of organic sludge and waste as an alternative fuel is cost effective and has environmental benefits.

Artificial aggregate made from waste stone sludge and waste silt

In this research, waste stone sludge obtained from slab stone processing and waste silt from aggregate washing plants were recycled to manufacture artificial aggregate. Fine-powdered stone sludge was mixed with waste silt of larger particle size; vibratory compaction was applied for good water permeability, resulting in a smaller amount of solidifying agent being used. For the densified packing used in this study, the mix proportion of waste stone sludge to waste silt was 35:50, which produced artificial aggregate of more compact structure with water absorption rate below 0.1%. In addition, applying vibratory compaction of 33.3 Hz to the artificial aggregate and curing for 28 days doubled the compressive strength to above 29.4 MPa. Hence, recycling of waste stone sludge and waste silt for the production of artificial aggregate not only offers a feasible substitute for sand and stone, but also an ecological alternative to waste management of sludge and silt.

Impact of flood damage on pollutant removal efficiencies of a subtropical urban constructed wetland

Typhoons and hurricanes in subtropical/tropical regions can induce significant environmental changes (e.g., mass flooding and inundations). However, the damage to the pollutant removal efficiencies of constructed wetlands brought about by these natural disturbances has been neglected in major studies conducted in temperate climates. Therefore, this study compares the pollutant removal performance of a constructed wetland in the Danshui River Basin, before and after the system was inundated with flooding from Typhoon Krosa in 2007. The pollutant removal performance of the free water surface (FWS) constructed wetland was investigated monthly from September 2006 to April 2008. Results of the study demonstrated that this FWS wetland effectively removed 64.3% BOD, 98.9% NH(4)-N, and 39.5% Total-P before Typhoon Krosa. However, the extensive flooding caused by Typhoon Krosa swept over most of the aboveground plant community and deposited the sediment onto the bottom of each compartment. Subsequently, reduced pollutant removal efficiencies were observed. Only 37.7% BOD, 35.1% NH(4)-N, and 31.8% Total-P were removed after this event, although the flow regime was immediately restored. Comparing the water quality data for the FWS wetland before and after Typhoon Krosa revealed the immediate, quantitative damage to the pollutant removal performance caused by the typhoon's inundation. Consequently, a high-flow bypass and additional preventive measures would protect any constructed wetland in areas subject to typhoons.

Extraction of chromium, copper, and arsenic from CCA-treated wood using biodegradable chelating agents

The aim of this study was to investigate the biodegradable chelating agents S,S-ethylenediaminedisuccinic acid (SS-EDDS) and nitrilotriacetic acid (NTA) as potential alternatives and compare them with ethylenediaminetetraacetic acid (EDTA) for effectiveness. Extraction of heavy metals from chromated copper arsenate (CCA)-treated wood with EDDS, NTA, or EDTA solvent was evaluated at various solvent pH levels and stoichiometric ratios. Based on the present data, the recommended extraction conditions are pH 4.0 and EDDS-CCA stoichiometric ratios of 10.

Study on cement mortar and concrete made with sewage sludge ash

This study investigated the feasibility of reusing wastewater sludge ash in construction materials to replace partial materials. Wastewater sludge sampled from thermal power plant was burned into sludge ash at 800°C in the laboratory. The sludge incineration ash has low heavy metal including Pb, Cd, Cr and Cu, so it belongs to general enterprise waste. The chemical composition of sludge incineration ash was summed up in SiO₂, CaO, Fe₂O₃ and MgO. Then the wastewater sludge ash is also found to be a porous material with irregular surface. When the sludge ash was used to replace mortar or concrete cement, its water-adsorption capability will result in the reduction of mortar workability and compressive strength. Cement is being substituted for sludge ash, and 10 percent of sludge ash is more appropriate. Sludge ash is reused to take the place of construction materials and satisfies the requests of standard specification except for higher water absorption.

Nucleophosmin in the pathogenesis of arsenic-related bladder carcinogenesis revealed by quantitative proteomics

To investigate the molecular mechanisms of arsenic (As)-associated carcinogenesis, we performed proteomic analysis on E7 immortalized human uroepithelial cells after treatment with As in vitro. Quantitative proteomics was performed using stable isotope dimethyl labeling coupled with two-dimensional liquid chromatography peptide separation and mass spectrometry (MS)/MS analysis. Among 285 proteins, a total of 26 proteins were upregulated (ratio>2.0) and 18 proteins were downregulated (ratio<0.65) by As treatment, which are related to nucleotide binding, lipid metabolism, protein folding, protein biosynthesis, transcription, DNA repair, cell cycle control, and signal transduction. This study reports the potential significance of nucleophosmin (NPM) in the As-related bladder carcinogenesis. NPM was universally expressed in all of uroepithelial cell lines examined, implying that NPM may play a role in human bladder carcinogenesis. Upregulation of NPM tends to be dose- and time-dependent after As treatment. Expression of NPM was associated with cell proliferation, migration and anti-apoptosis. On the contrary, soy isoflavones inhibited the expression of NPM in vitro. The results suggest that NPM may play a role in the As-related bladder carcinogenesis, and soybean-based foods may have potential in the suppression of As/NPM-related tumorigenesis.

Treatment of septic tank effluents by a full-scale capillary seepage soil biofiltration system

The purpose of this study is to evaluate the efficiency of septic tank effluent treatment by an underground capillary seepage soil biofiltration system in a suburban area of Taipei, Taiwan. In contrast to traditional subsurface wastewater infiltration systems, capillary seepage soil biofiltration systems initially draw incoming influent upwards from the distribution pipe by capillary and siphonage actions, then spread influent throughout the soil biofiltration bed. The underground capillary seepage soil biofiltration system consists of a train of underground treatment units, including one wastewater distribution tank, two capillary seepage soil biofiltration units in series, and a discharge tank. Each capillary seepage soil biofiltration unit contains one facultative digestion tank and one set of biofiltration beds. At the flow rate of 50 m3/day, average influent concentrations of biochemical oxygen demand (BOD), suspended solid (SS), ammonia nitrogen (NH3-N), and total phosphates (TP), were 36.15 mg/L, 29.14 mg/L, 16.05 mg/L, and 1.75 mg/L, respectively. After 1.5 years of system operation, the measured influent and effluent results show that the treatment efficiencies of the soil biofiltration system for BOD, SS, NH3-N, TP, and total coliforms are 82.96%, 60.95%, 67.17%, 74.86%, and 99.99%, respectively.

Viscoelastic thin polymer films under transient residual stresses: two-stage dewetting on soft substrates

A nonmonotonic, two-stage dewetting behavior was observed for spin coated thin viscoelastic polymer films on soft elastic substrates. At times shorter than the relaxation time of the polymer (t<tau_{rep}), dewetting generated deep trenches in the soft rubbery substrate which, in turn, almost stopped dewetting. At later stages (t>>tau_{rep}), dewetting accelerated, accompanied by an unstable rim. However, holes nucleated at t<tau_{rep} showed only this second-stage behavior. Our observations are attributed to large elastic deformations in the substrate caused by transient residual stresses within the film.

Sequential extraction for evaluating the leaching behavior of selected elements in municipal solid waste incineration fly ash

A sequential extraction method has been applied for the determination of binding forms of trace elements in the municipal solid waste incineration (MSWI) fly ash and evaluating their leaching behavior in view of their potential environmental impact. The elemental determinations in the different leachates are performed by ICP-AES and ICP-MS, respectively. The morphology and mineralogical phases after extraction step were performed by scanning electron microscopy (SEM). Total of 20 elements in the samples are investigated. A reference material of city waste incineration fly ash (BCR No. 176) is also tested to examine the applicability as well as accuracy of the proposed method. The sum of most elements present in the individual fractions shows a good agreement with the total elemental concentrations. The extraction efficiencies are generally higher than 80% except for that of Cr and V. The extractable data of most elements give information about the binding forms of various elements in both incineration fly ashes. It was found that the elements such as Ca, K, Na, Pb, Zn, Cd, Cu and Sr have exhibited a remarkable mobility in fly ash. More than half of them would be dissolved or exchanged under a mild leaching condition. The toxic elements such as Pb, Cd, Zn and Cu have a great potential to be released into the environment under normal conditions.

Leachability of metals from sludge-based artificial lightweight aggregate

Metal sludge from industrial wastewater treatment plants was mixed with mining residues to be recycled into lightweight aggregate (LWA) through sintering at different temperatures. The physical properties of the LWA thus obtained were examined by scanning electron microscopy analyzer (SEM) coupled with an energy dispersive X-ray analyzer (EDX). The sequential extraction method combined with inductively coupled plasma atomic emission spectrometry (ICP-AES) was employed to determine the concentration and distribution of hazardous toxic elements in the metal sludge-based artificial LWA. The results show that the leaching concentrations of Cd, Cr, Cu, and Pb present in the non-sintered raw aggregate pellets reached 7.4, 68.0, 96.0, and 61.4 mg/l, respectively, far exceeding the regulatory threshold. Sintering at 1150 degrees C for 15 min results in stronger chemical bonds being formed between the elements. Hence, after the first three steps of sequential extraction, the concentrations of Cr, Cu, and Pb reached 2.69, 1.50, and 1.88 mg/l at 1150 degrees C, while the final residues had total concentrations of 96.1, 88.4, and 60.6 mg/kg, respectively, with Cd undetected in both phases. The concentration levels fell within the regulatory threshold, indicating that the LWA fabricated from recycled metal sludge contains elements that are toxic and hazardous but not leached. Having no harmful effect on the environment, the metal sludge-based artificial LWA is not only safe but also practical with good physical properties.

Bilateral traumatic carotid-cavernous fistulae: Strategies for endovascular treatment

BACKGROUND

Most traumatic carotid-cavernous fistula/e (TCCF) are unilateral, and simultaneous bilateral TCCF are uncommon. The purpose of this study was to evaluate the angiographic architecture of bilateral TCCF and report our experience with their endovascular management.

METHOD

Over 15 years, 252 consecutive patients with TCCF were referred to our institute for endovascular treatment. Bilateral TCCF occurred in 5 men and 2 women with a mean age of 31 years. The angiographic architectures of bilateral TCCF were evaluated with cerebral angiography. All patients underwent a single session of transarterial embolisation by using various permanent embolic materials and were followed up clinically or with angiography for a mean of 22 months (range 9-36 months).

FINDINGS

All patients presented with neuro-ophthalmic symptoms and signs. No new instances of cerebrovascular ischemia or intracranial haematoma resulted from bilateral TCCF. All fistulae were associated with partial arterial steal and were successfully occluded by using a detachable balloon and/or a detachable coil with or without a liquid adhesive. Of 14 TCCF, 9 were completely obliterated with preserved flow of the internal carotid artery (ICA). In the other 5 fistulae, the ICA had to be sacrificed to achieve occlusion because the anatomy of the fistula was complex. All fistula related symptoms resolved immediately or gradually during clinical follow up. No clinically significant procedure related neurological complications or recurrent fistulae were observed.

CONCLUSIONS

All bilateral TCCF were associated with a partial arterial steal phenomenon. Single session endovascular treatment using various embolic materials was effective in managing these high-flow fistulae. In all patients, it was possible to preserve one or both ICAs.

Production of lightweight aggregates from mining residues, heavy metal sludge, and incinerator fly ash

In this study, artificial lightweight aggregate (LWA) manufactured from recycled resources was investigated. Residues from mining, fly ash from an incinerator and heavy metal sludge from an electronic waste water plant were mixed into raw aggregate pellets and fed into a tunnel kiln to be sintered and finally cooled rapidly. Various feeding and sintering temperatures were employed to examine their impact on the extent of vitrification on the aggregate surface. Microstructural analysis and toxicity characteristic leaching procedure (TCLP) were also performed. The results show that the optimum condition of LWA fabrication is sintering at 1150 degrees C for 15 min with raw aggregate pellets fed at 750 degrees C. The rapidly vitrified surface envelops the gas produced with the increase in internal temperature and cooling by spraying water prevents the aggregates from binding together, thus forming LWA with specific gravity of 0.6. LWA produced by sintering in tunnel kiln shows good vitrified surface, low water absorption rate below 5%, and low cylindrical compressive strength of 4.3 MPa. In addition, only trace amounts of heavy metals were detected, making the LWA non-hazardous for construction use.

Prediction of Alzheimer's disease in mild cognitive impairment: a prospective study in Taiwan

The relationship between apolipoprotein E (ApoE) and clinical manifestations of mild cognitive impairment (MCI) has not been investigated in non-Caucasian populations. This prospective study was conducted in an ethnic Chinese population to evaluate the correlations of ApoE genotype, cognitive performance, medial temporal structure volumes, and clinical outcome in amnestic MCI. Twenty normal elders, 58 MCI, and 20 mild Alzheimer's disease (AD) patients received neuropsychological, MRI, and ApoE genotype assessments at baseline. Patients with MCI had intermediate cognitive performance and hippocampal volumes between those in normal and AD groups. In each diagnostic group, epsilon4 carriers (E4+) consistently had smaller hippocampal volume than non-carriers (E4-) did. Nineteen MCI subjects (32.7%) converted to AD during the 3-year study period. Compared with MCI non-converters and E4- MCI converters, E4+ MCI converters had the smallest hippocampal volume. However, epsilon4 was not a predictor for AD. Both cognitive performance and hippocampal volume were predictive for progression to AD. However, stepwise Cox regression model integrating both neuropsychological and radiological variables showed that global cognitive performance was the only significant predictor for AD. A poor global cognitive score may be more crucial than a small hippocampal volume in the prediction of AD.

Percutaneous vertebroplasty for patients with osteoporosis: a one-year follow-up

PURPOSE

To evaluate changes in height and wedge angle of treated vertebral bodies and kyphosis angle 1 year after vertebroplasty.

MATERIAL AND METHODS

We reviewed radiographs of 95 vertebral bodies treated with vertebroplasty in 60 patients with osteoporosis. Only vertebral bodies with imaging evidence of a new fracture or avascular necrosis received vertebroplasty. Images were obtained for evaluation before vertebroplasty (B), within 2 weeks after vertebroplasty (T), and after 1 year (T1).

RESULTS

The mean wedge angle decreased by 5.4 degrees from B to T1. Mean of the anterior, central, and posterior heights of the fractured bodies increased by 12.6%, 9.6%, and 3.1%, respectively, from B to T1. The kyphosis angle improved by 3.2 degrees initially from B to T, but the improvement later disappeared. In 48% of these patients, a new fracture developed after vertebroplasty, and 63% of the fractures were adjacent to a vertebroplasty-treated vertebral body.

CONCLUSION

The increase in height and wedge angle of the vertebral bodies generally lasted at least 1 year. Improvement in kyphosis angles was lost 1 year after vertebroplasty because new fractures occurred in 48% of these patients. Prevention of new fractures after vertebroplasty remains an important task.

Carotid blowout treated by direct percutaneous puncture of internal carotid artery with temporary balloon occlusion

SUMMARY

Direct percutaneous puncture of a cervical carotid pseudoaneurysm for coil placement or acrylic embolization is described for the endovascular management of acute carotid blowout. However, direct puncture of the internal carotid artery (ICA) for the endovascular management of carotid blowout has not been described. We report a difficult case of acute carotid blowout syndrome in a patient who had radiation- induced occlusion of the right common carotid artery with vasculopathy and pseudoaneurysm in the right cervical ICA. Collaterals from the branches of the controlateral external carotid artery (ECA) anastomosed with branches of right ECA supplied the vasculopathy. We performed direct percutaneous puncture of the bulb of the right ICA using a spinal needle and placed fiber coils to occlude antegrade flow of the artery. During the injection of a mixture of N-butyl cyanoacrylate and lipiodol oil for embolization of the remaining carotid bulb, we transiently inflated an occlusion balloon in the controlateral common carotid artery to further arrest antegrade flow in the ICA. The vasculopathy and pseudoaneurysm of the right cervical ICA were successfully embolized, with preservation of the distal branches of the right ICA.

Neuroradiological findings in atypical teratoid/rhabdoid tumor of the central nervous system

PURPOSE

To evaluate the computed tomography (CT) and magnetic resonance imaging (MRI) findings of atypical teratoid tumor/rhabdoid tumor (AT/RT) of the central nervous system (CNS).

MATERIAL AND METHODS

Twenty cases of CNS AT/RT have been found over the past 23 years in our hospital; these involving 11 boys and 9 girls whose mean age at diagnosis was 5.5 years. Their clinical data, the CT, and MRI findings were reviewed retrospectively.

RESULTS

AT/RT was located in the cerebellum in 15 cases. Four cases arose from the supratentorial region, while only one occurred primarily in the lumbar spinal cord. Almost all cases revealed heterogeneous intensity and heterogeneous enhancement. Peripheral cystic components were common. Survival time ranged from 2 months to 3 years, with a mean survival of 11.6 months.

CONCLUSION

Most cases of AT/RT are located in the cerebellum. The radiologic manifestations are non-specific. The diagnosis mainly depends on the pathologic findings. However, AT/RT should still remain in the differential diagnosis of brain tumors in young children, especially those located in the cerebellar hemisphere and with eccentric cysts.

Two novel mutations of the glycine receptor gene in a Taiwanese hyperekplexia family

The authors report a Taiwanese family with autosomal recessive hyperekplexia. Two novel mutations, W96C (from the paternal allele) and R344X (from the maternal allele), which are located in exon 4 and exon 7 of the GLRA1 gene, were identified in this family. A series of electrophysiologic investigations were conducted in one of the probands, and the results suggest that the "startle center" is located subcortically.

Environmental risk factors of young onset Parkinson's disease: a case-control study

While the cause of Parkinson's disease (PD) remains unknown, recent evidence suggests certain environmental factors, such as well water drinking, herbicides and pesticides exposure, and neurotoxins, may trigger the chain of oxidative reactions culminating in the death of dopaminergic neurons in substantia nigra to cause parkinsonism. Most studies to date focused on PD with old age onset. However, there is a peculiar group of parkinsonian patients, the young onset Parkinson's disease (YOPD), in whom the age of onset is before 40. It is intriguing to know whether earlier exposure to the putative neurotoxin(s) may contribute to the earlier onset. We therefore conducted this case-control study in which 60 PD patients, 30 YOPD patients and the same number of age- and sex-matched young controls were included. Using logistic regression, we found well water drinking and head injury were risk factors for the development of YOPD. When YOPD patients were compared with PD, we found head injury and exercise were the significant predictors. Keeping all other variables constant, head injury was a risk factor and exercise appeared to be a protective factor. We conclude early exposure to well water drinking and head trauma may trigger and expedite the appearance of parkinsonian features, but such acceleration may be prevented through regular exercise.

Correlation of gas chromatographic properties of chlorobenzenes and polychlorinated biphenyls with the occurrence of reductive dechlorination by untamed microorganisms

To understand the dechlorination ability of chlorobenzenes (CBs) and polychlorinated biphenyls (PCBs) by untamed microorganisms under anaerobic condition and to correlate gas chromatographic properties with the occurrence of reductive dechlorination, introduction of CBs and PCBs in the culture medium inoculated with microorganisms from sludge and sediment, respectively, were performed. Three kinds of culture media preparing from sludge, river water and a synthetic medium were used in the experiments. HCB was degraded to 1,3,5-trichlorobenzene (1,3,5-TCB) and 1,3-dichlorobenzene (1,3-DCB) in both sludge medium and synthetic medium with inoculated microorganisms. Three PCB congeners including 2,3,4-, 3,4,5- and 2,3,4,5-CBp (chlorinated biphenyl) were not found to be dechlorinated in the river water medium with inoculation culture but to be dechlorinated in the synthetic medium. MNDO methodology was used to compute theoretical dechlorination reaction heats and GC-ECD techniques were used to estimate chromatographic data of CB and PCB congeners. Both CB and PCB congeners showed that dechlorination by untamed microorganisms under anaerobic mixed cultures were more likely to occur when larger amounts of energy were released and greater deltaln RRT value between the parent congener and the daughter product was observed. Deltaln RRT provided a more precise information on the singularity of PCBs ortho-dechlorination in an aspect of thermodynamic favorable rule.

Corticotropin-releasing hormone (CRH) as a regulator of waking

Corticotropin-releasing hormone (CRH), expressed in widely distributed regions of the central nervous system (CNS), mediates the hypothalamic-pituitary-adrenal (HPA) axis and autonomic components of responses to stressors. Sleep, a fundamental CNS process, is altered in response to a variety of stressors. Although there is an extensive literature on the role of CRH in responses to stressors, there is relatively little information on the role of CRH in normal, spontaneous behavior. We hypothesize that CRH is involved in the regulation of waking in the absence of overt stressors. Some of the early evidence supporting this hypothesis was indirect. We summarize in this review studies from our laboratory and others that provide direct evidence that CRH is involved in the regulation of spontaneous waking. We also suggest on the basis of recent studies that some effects of CRH on waking and sleep may be mediated by actions within the CNS of the immunomodulatory cytokine interleukin (IL)-1. Collectively, these observations suggest that CRH contributes to the regulation of spontaneous waking in the absence of stressors, and also indicate a potential mechanism mediating complex alterations in sleep that occur in response to immune challenge.

Rag-1 mutations associated with B-cell-negative scid dissociate the nicking and transesterification steps of V(D)J recombination

Some patients with B-cell-negative severe combined immune deficiency (SCID) carry mutations in RAG-1 or RAG-2 that impair V(D)J recombination. Two recessive RAG-1 mutations responsible for B-cell-negative SCID, R621H and E719K, impair V(D)J recombination without affecting formation of single-site recombination signal sequence complexes, specific DNA contacts, or perturbation of DNA structure at the heptamer-coding junction. The E719K mutation impairs DNA cleavage by the RAG complex, with a greater effect on nicking than on transesterification; a conservative glutamine substitution exhibits a similar effect. When cysteine is substituted for E719, RAG-1 activity is enhanced in Mn(2+) but remains impaired in Mg(2+), suggesting an interaction between this residue and an essential metal ion. The R621H mutation partially impairs nicking, with little effect on transesterification. The residual nicking activity of the R621H mutant is reduced at least 10-fold upon a change from pH 7.0 to pH 8.4. Site-specific nicking is severely impaired by an alanine substitution at R621 but is spared by substitution with lysine. These observations are consistent with involvement of a positively charged residue at position 621 in the nicking step of the RAG-mediated cleavage reaction. Our data provide a mechanistic explanation for one form of hereditary SCID. Moreover, while RAG-1 is directly involved in catalysis of both nicking and transesterification, our observations indicate that these two steps have distinct catalytic requirements.

Magnetic resonance imaging appearance of intradural spinal lipoma

Intradural spinal lipoma not associated with spinal dysraphism is a rare tumor often presenting with nonspecific symptoms and indolent clinical course. Its intradural location and fat component is the key for proper preoperative diagnosis, which could hardly be made by traditional imaging studies including plain film and myelography. Both CT and MRI can reveal the fat component of the tumor, but MRI is superior to CT in demonstrating its relationship with adjacent normal nerve tissue. We report a 32-year-old man who had back pain for years and the symptom progressed rapidly in recent two months. MRI revealed an intradural tumor at T12 level with high signal intensity on both T1- and T2-weighted images. The signal intensity dropped dramatically with fat saturation technique, which confirmed fat as its main component. The patient received surgery and the tumor was proved to be an intraspinal lipoma.

Comparisons of PCBs dechlorination occurrences in various contaminated sediments

A comparison was made of reductive dechlorination occurrences of polychlorinated biphenyls (PCBs) by microorganisms collected from contaminated sediments including Er-Jen River (Tainan, Taiwan), Hudson River (Ft. Edward, NY), Silver Lake (Pittsfield, MA) and Puget Sound (Washington State). Comparisons was made in terms of chromatographic data (referring to the biological activity, including microbial availability) and thermodynamic data (demonstrating the selectivity of anaerobic microorganisms in the dechlorination of chlorinated compounds). Chromatographic data was established in terms of difference in relative retention time (delta ln RRT) and thermodynamic data was estimated as heat of reaction (delta H(r)0). Both were calculated and correlated to occurrences of dechlorination reactions. Observed dechlorination reactions for individually introducing PCB congener had delta ln RRT levels measured as >0.47 (Er-Jen River), >0.29 (Hudson River), >0.36 (Silver Lake) and >0.45 (Puget Sound, for Aroclor 1254 dechlorination). Critical of delta H(r)0 and delta ln RRT values showed that Hudson River and Silver Lake microorganisms were capable of dechlorinating PCBs through reactions with larger H(r)0 value (lower levels of released energy) and smaller delta ln RRT value compared with those found in Er-Jen River and Puget Sound sediments. Differences in the critical delta ln RRT values of these sediments may be due to differences in their levels of PCB contamination.

Sequential MR studies of a patient with white matter disease presenting psychotic symptoms: ADEM versus single-episode MS

Acute disseminated encephalomyelitis (ADEM) and multiple sclerosis (MS) are both demyelinating white matter disorders. It is difficult to differentiate ADEM from single episode MS because of the similar clinical presentation, cerebral spinal fluid (CSF) analysis, histological finding and magnetic resonance image (MRI) appearance. We report an ADEM case with unusual clinical presentations of predominant psychiatric symptoms, and relatively long disease course. Initially, we were not able to distinguish it from single episode MS. By means of sequential MR images followed up 2 years and spectroscopy studies, and the dramatic clinical improvement after corticosteroid therapy, ADEM was diagnosed as the disease entity of this patient. In this case report we will present the MR findings of this patient and discuss the differentiation between the ADEM and MS.

Image evaluation of suprazygomatic masticator space lesions

In order to understand lesions involving the suprazygomatic masticator space (SZMS) demonstrated on computered tomography (CT) or magnetic resonance (MR) images, we collected 45 cases of lesions in SZMS. There were hematomas in 26 cases, tumors in 16 cases, and abscesses in 3 cases. The location of these lesions in compartments of the SZMS and adjacent structures was analyzed. Most commonly hematoma was found in the deep loose connective tissue (80.8%), followed by the superficial dense connective tissue (61.5%). Only 2 SZMS hematoma involved the superficial fat pad. Five patients had air accumulation in the SZMS, and all were in the deep fat pad and with maxillary sinus fracture. Of the sixteen cases which were tumors, 12 were extended from adjacent structures, and four were primary tumor. In cases of tumor, compartments of SZMS involved most frequently were temporal muscles (15 of 16 cases), followed by deep fat pad (8 of 16 cases). The connective tissue layer of SZMS is a communication pathway for superficial spread of infection, hematoma, or tumor invasion to or from the scalp and face. Compartments of deep fat pad and temporal muscle are also pathways for the spread of disease to or from the face, intracranium and orbit. The primary tumors in infratemporal fossa and SZMS are rare. Malignant tumors in SZMS usually come from surrounding spaces.