Flexible and transparent composite nanofibre membrane that was fabricated via a "green" electrospinning method for efficient particulate matter 2.5 capture

Electrospun Composite Proton-Exchange and Anion-Exchange Membranes for Fuel Cells

A fuel cell is an electrochemical device that converts the chemical energy of a fuel and oxidant into electricity. Cation-exchange and anion-exchange membranes play an important role in hydrogen fed proton-exchange membrane (PEM) and anion-exchange membrane (AEM) fuel cells, respectively. Over the past 10 years, there has been growing interest in using nanofiber electrospinning to fabricate fuel cell PEMs and AEMs with improved properties, e.g., a high ion conductivity with low in-plane water swelling and good mechanical strength under wet and dry conditions. Electrospinning is used to create either reinforcing scaffolds that can be pore-filled with an ionomer or precursor mats of interwoven ionomer and reinforcing polymers, which after suitable processing (densification) form a functional membrane. In this review paper, methods of nanofiber composite PEMs and AEMs fabrication are reviewed and the properties of these membranes are discussed and contrasted with the properties of fuel cell membranes prepared using conventional methods. The information and discussions contained herein are intended to provide inspiration for the design of high-performance next-generation fuel cell ion-exchange membranes.

Study on the Preparation and Lipophilic Properties of Polyvinyl Alcohol (PVA) Nanofiber Membranes via Green Electrospinning

As an environmentally friendly water-soluble polymer, polyvinyl alcohol (PVA) has attracted extensive attention because of its non-toxic, degradable, low cost, and good biocompatibility. Electrospinning is a kind of nanotechnology, and the nanofiber membrane prepared by it has the advantages of large surface area-to-volume ratios, nano- to micron-sized fibers, etc. Herein, a simple and facile one-step green electrospinning method was developed to fabricate various environmentally friendly PVA nanofiber membranes. The lipophilic properties of PVA membranes were investigated and optimized according different PVA concentrations. The PVA electrospun fiber prepared from the solution at a concentration of 10 wt% had the highest adsorption capacity for the adsorption of new and waste engine oils, and the waste engine oil adsorption capacity (12.70 g/g) was higher than that of new engine oil (11.67 g/g). It also has a relatively large BET surface area (12.05 m2/g), a pore volume (0.04 cm3/g), and an appropriate pore diameter (13.69 nm) and fiber diameter (174.21 nm). All electrospun PVA membranes showed excellent lipophilic properties due to their oil contact angles of much less than 30°. Therefore, PVA electrospun fibrous membranes have great application potential in the field of purifying engine oil due to the excellent lipophilic properties and oil absorption capacity.

High-performance anti-haze window screen based on multiscale structured polyvinylidene fluoride nanofibers

Indoor air quality (IAQ) has assumed new significance given the extensive amount of time spent indoor due to the coronavirus pandemic and particulate matter (PM) pollution. Accordingly, the development of window air filters to effectively intercept PM from outdoor air under natural ventilation conditions is an important research topic. However, most existing filters inevitably suffer from the compromise among filtration capability, transparency, and air permeability. In this study, we fabricate a high-performance transparent air filter to improve IAQ via natural ventilation. polyvinylidene fluoride (PVDF) superfine nanofibers of size 20-35 nm are prepared using extremely dilute solution electrospinning; a multi-scale nanofiber structure is then designed. By adjusting the ratio of PVDF superfine nanofibers (SNs) to PVDF coarse fibers (CNs), we balance the structure-performance relationship. Benefiting from the multiscale structural features that include a small pore size (0.72 μm) and high porosity (92.22%), the resulting filters exhibit excellent performance including high interception efficiency (99.92%) for PM_0.3, low air resistance (69 Pa), high transparency (∼80%) and stable filtration after 100 h of UV irradiation. This work describes a new strategy for the fabrication of nanofibers with true-nanoscale diameters and the design of high-performance air filters.

The preparation of electrospun PVDF/TBAC multi morphology nanofiber membrane and its application in direct contact membrane distillation

Microporous membrane with a hydrophobic surface, high porosity and narrow pore size distribution is the ideal membrane distillation (MD) membrane. The electrospun membranes for MD is a new type and effective way to seawater desalination. Herein, a novel polyvinylidene fluoride (PVDF)/ tetrabutylammonium chloride (TBAC) electrospun nanofiber membrane (ENMs) fabricated apply to for direct contact membrane distillation (DCMD). Combine with the spinning condition, the characteristic and content of TBAC significant effect on the multi morphology structure of nanofiber. Therefore, the porous structure and morphology of PVDF/TBAC ENMs can be well-designed by optimizing relative humidity and TBAC concentration in spinning process, three different structure nanofiber membranes were obtained. Lab-scale setup was used to test membrane separation performance. The result indicated that the ultrafine ENMs with 0.025 mol/L TBAC presented a steady water flux of about 20.6 L/(m² h) and a high-efficiency salt rejection rate of over 99%. PVDF/TBAC ENMs are expected to provide a solution for development of efficient water treatment membrane. This article is protected by copyright. All rights reserved.

Nanofibrous Photocatalytic Membranes Based on Tailored Anisotropic Gold/Ceria Nanoparticles

The combination of plasmonic nanoparticles with semiconductor photocatalysts is a good strategy for synthesizing highly efficient photocatalysts. Such binary nanoparticles have demonstrated enhanced catalytic activity in comparison to either plasmonic catalysts or semiconductor catalysts. However, problematic recovery and limited long-term colloidal stability of those nanoparticles in suspension limit their wide use in catalysis. To palliate to such limitations, we embedded binary nanoparticles in polymer fibers to design photocatalytic membranes. First, we used the selective over-growth of crystalline cerium oxide on the gold nanoparticle template with distinct shapes. Gold nanospheres, gold nanorods, and gold nanotriangles were used as the template for the growth of the cerium oxide domains. Then, the resulting nanoparticles were used to catalyze model reactions in suspensions. The gold nanoparticles covered with patches of cerium oxide outperformed the fully covered and naked nanoparticles in terms of catalytic efficiency. Finally, the most efficient binary nanostructures were successfully embedded in nanofibrous membranes by colloidal electrospinning and used in water remediation experiments in a flow-through reactor.

Simultaneous trace-level monitoring of seven opioid analgesic drugs in biological samples by pipette-tip micro solid phase extraction based on PVA-PAA/CNT-CNC composite nanofibers followed by HPLC-UV analysis

Electrospun poly(vinyl alcohol)-(PVA)-poly(acrylic acid) (PAA)/carbon nanotubes(CNTs)-cellulose nanocrystal (CNC) (PVA-PAA/CNT-CNC) composite nanofibers were prepared and characterized using Fourier transform-infrared spectroscopy and field emission scanning electron microscopy. The resultant composite was used as an effective and novel sorbent for pipette-tip micro-solid phase extraction (PT-μSPE) of seven opioid analgesics (OAs) in biological samples followed by HPLC-UV analysis. Addition of CNT-CNC with the high specific surface area and plenty of OH-functional groups endows the nanofibers with considerable extraction efficiency. Under the optimum conditions, the linearity was obtained in the range 1.5 to 700.0 ng mL^-1 for morphine, codeine, oxycodone, and tramadol, and 0.5 to 1000.0 ng mL^-1 for nalbuphine, thebaine, and noscapine with coefficient of determination (r²) ≥ 0.9990. Detection limits (LODs) based on S/N = 3 were in the range of 0.15-0.50 ng mL^-1. The relative standard deviations (RSDs) of 4.1-5.4% (intra-day, n = 5) and 5.2-6.4% (inter-day, n = 3) for three consecutive days were achieved. Finally, the efficiency of the PT-μSPE-HPLC-UV method was evaluated for the determination of OAs in human plasma and urine samples with good recoveries (87.3 to 97.8%). A: Schematic illustration for the preparation of PVA-PAA/CNT-CNC composite nanofibers. B: Schematic presentation of applying PVA-PAA/CNT-CNC composite nanofibers as the sorbent in pipette-tip micro solid-phase extraction (PT-μSPE) for the preconcentration of seven opioid analgesic drugs in biological samples before HPLC-UV analysis.

Needleless electrospun phytochemicals encapsulated nanofibre based 3-ply biodegradable mask for combating COVID-19 pandemic

The emergence of COVID-19 pandemic has severely affected human health and world economies. According to WHO guidelines, continuous use of face mask is mandatory for personal protection for restricting the spread of bacteria and virus. Here, we report a 3-ply cotton-PLA-cotton layered biodegradable face-mask containing encapsulated phytochemicals in the inner-filtration layer. The nano-fibrous PLA filtration layer was fabricated using needleless electrospinning of PLA & phytochemical-based herbal-extracts. This 3-layred face mask exhibits enhanced air permeability with a differential pressure of 35.78 Pa/cm² and superior bacterial filtration efficiency of 97.9% compared to conventional face masks. Close-packed mesh structure of the nano-fibrous mat results in effective adsorption of particulate matter, aerosol particles, and bacterial targets deep inside the filtration layer. The outer hydrophobic layer of mask exhibited effective blood splash resistance up to a distance of 30 cm, ensuring its utilization for medical practices. Computational analysis of constituent phytochemicals using the LibDock algorithm predicted inhibitory activity of chemicals against the protein structured bacterial sites. The computational analysis projected superior performance of phytochemicals considering the presence of stearic acid, oleic acid, linoleic acid, and Arachidic acid exhibiting structural complementarity to inhibit targeted bacterial interface. Natural cotton fibers and PLA bio-polymer demonstrated promising biodegradable characteristics in the presence of in-house cow-dung based biodegradation slurry. Addition of jaggery to the slurry elevated the biodegradation performance, resulting in increment of change of weight from 07% to 12%. The improved performance was attributed to the increased sucrose content in biodegradation slurry, elevating the bacterial growth in the slurry. An innovative face mask has shown promising results for utilization in day-to-day life and medical frontline workers, considering the post-pandemic environmental impacts.

Application of Electrospinning in Antibacterial Field

In recent years, electrospun nanofibers have attracted extensive attention due to their large specific surface area, high porosity, and controllable shape. Among the many applications of electrospinning, electrospun nanofibers used in fields such as tissue engineering, food packaging, and air purification often require some antibacterial properties. This paper expounds the development potential of electrospinning in the antibacterial field from four aspects: fiber morphology, antibacterial materials, antibacterial mechanism, and application fields. The effects of fiber morphology and antibacterial materials on the antibacterial activity and characteristics are first presented, then followed by a discussion of the antibacterial mechanisms and influencing factors of these materials. Typical application examples of antibacterial nanofibers are presented, which show the good prospects of electrospinning in the antibacterial field.

Solvothermal Preparation of a Lanthanide Metal-Organic Framework for Highly Sensitive Discrimination of Nitrofurantoin and l-Tyrosine

Metal-organic frameworks (MOFs) have been rapidly developed for their broad applications in many different chemistry and materials fields. In this work, a multi-dentate building block 5-(4-(tetrazol-5-yl)phenyl)-isophthalic acid (H₃L) containing tetrazole and carbolxylate moieties was employed for the synthesis of a two-dimensional (2D) lanthanide MOF [La(HL)(DMF)₂(NO₃)] (DMF = N,N-dimethylformamide) (1) under solvothermal condition. The fluorescent sensing application of 1 was investigated. 1 exhibits high sensitivity recognition for antibiotic nitrofurantoin (K_sv: 3.0 × 10³ M⁻¹ and detection limit: 17.0 μM) and amino acid l-tyrosine (K_sv: 1.4 × 10⁴ M⁻¹ and detection limit: 3.6 μM). This work provides a feasible detection platform of 2D MOFs for highly sensitive discrimination of antibiotics and amino acids.

Multistructured Electrospun Nanofibers for Air Filtration: A Review

Air filtration materials (AFMs) have gradually become a research hotspot on account of the increasing attention paid to the global air quality problem. However, most AFMs cannot balance the contradiction between high filtration efficiency and low pressure drop. Electrospinning nanofibers have a large surface area to volume ratio, an adjustable porous structure, and a simple preparation process that make them an appropriate candidate for filtration materials. Therefore, electrospun nanofibers have attracted increased attention in air filtration applications. In this paper, first, the preparation methods of high-performance electrospun air filtration membranes (EAFMs) and the typical surface structures and filtration principles of electrospun fibers for air filtration are reviewed. Second, the research progress of EAFMs with multistructures, including nanoprotrusion, wrinkled, porous, branched, hollow, core-shell, ribbon, beaded, nets structure, and the application of these nanofibers in air filtration are summarized. Finally, challenges with the fabrication of EAFMs, limitations of their use, and trends for future developments are presented.

Angiogenic potential of airbrushed fucoidan/polycaprolactone nanofibrous meshes

Implantation of biomaterials and hybrid constructs in tissue engineering approaches presents major limitations such as inflammatory reaction and the lack of vasculature integration. Therefore, new strategies are needed to enhance implant function, immune protection, and revascularization. In this work, we developed fibrous meshes composed of fucoidan (Fu), a sulfated polysaccharide extracted from brown algae, and polycaprolactone (PCL), a synthetic biodegradable polymer, using the airbrush technique. The chemical characterization by FTIR, EDS, and XPS confirmed the presence of the two polymers in the structure of airbrushed nanofibrous meshes (ANFM). Moreover, these nanofibrous exhibited good wettability and mechanical properties envisaging their application as templates for biomaterials and cell culture. The developed ANFM were directly cultured with human pulmonary microvascular endothelial (HPMEC-ST1.6R) cells for up to 7 days. Biological results demonstrated that ANFM comprising Fu promoted cellular attachment, spreading, and proliferation of human endothelial cells. The angiogenic potential of ANFM was further evaluated by onplantation of PCL and PCL/Fu ANFM in chick chorioallantoic membrane (CAM). In ovo and ex ovo results showed that the incorporation of Fu increased the pro-angiogenic potential of ANFM. Altogether, the results suggest that airbrush biocomposite meshes could be used as a biomaterial substrate to promote vascularization.

Promotion of Surgical Masks Antimicrobial Activity by Disinfection and Impregnation with Disinfectant Silver Nanoparticles

BACKGROUND

The COVID-19 pandemic is requesting highly effective protective personnel equipment, mainly for healthcare professionals. However, the current demand has exceeded the supply chain and, consequently, shortage of essential medical materials, such as surgical masks. Due to these alarming limitations, it is crucial to develop effective means of disinfection, reusing, and thereby applying antimicrobial shielding protection to the clinical supplies.

PURPOSE

Therefore, in this work, we developed a novel, economical, and straightforward approach to promote antimicrobial activity to surgical masks by impregnating silver nanoparticles (AgNPs).

METHODS

Our strategy consisted of fabricating a new alcohol disinfectant formulation combining special surfactants and AgNPs, which is demonstrated to be extensively effective against a broad number of microbial surrogates of SARS-CoV-2.

RESULTS

The present nano-formula reported a superior microbial reduction of 99.999% against a wide number of microorganisms. Furthermore, the enveloped H5N1 virus was wholly inactivated after 15 min of disinfection. Far more attractive, the current method for reusing surgical masks did not show outcomes of detrimental amendments, suggesting that the protocol does not alter the filtration effectiveness.

CONCLUSION

The nano-disinfectant provides a valuable strategy for effective decontamination, reuse, and even antimicrobial promotion to surgical masks for frontline clinical personnel.

High performance, environmentally friendly and sustainable nanofiber membrane filter for removal of particulate matter 1.0

Particulate matter (PM) air pollution is becoming more and more serious and dangerous to public health, especially in developing countries where industrialization is accelerating. The use of electrospun membrane-based materials for air filtration is a widespread and effective way to help individuals avoid air pollution. However, most electrospun membrane preparation processes require the use of organic solvents, resulting in secondary environmental pollution. In this study, an environmentally friendly polyvinyl alcohol (PVA) - tannic acid (TA) composite nanofiber membrane filter was prepared by the green electrospinning and the physical cross-linking method. The filtration efficiency of the membrane filter for PM_1.0 reached 99.5%, and the pressure drop was only 35 Pa. In addition, due to the existence of intermolecular hydrogen bond between PVA and TA, the mechanical properties of the nanofiber membrane were improved to meet the requirements of practical application of the filter. Therefore, the PVA-TA composite nanofiber membrane is expected to provide a solution for the development of efficient and environmentally friendly air filter.

Laminated polyacrylonitrile nanofiber membrane codoped with boehmite nanoparticles for efficient electrostatic capture of particulate matters

Particulate matters (PMs) air pollution is identified as the major threat to public health and climate. High-performance air filter technology based on various electrospun nanofibers is considered as an effective strategy to eliminate the effects of PMs air pollution. However, to date, nearly all the existing micro-/nanofibers are hard to meet both requirements of high PMs removal efficiency and long service life. In this work, we reported the production of laminated polyacrylonitrile(PAN)-boehmite nanoparticles (BNPs) nanofiber structured membrane by the electrospinning process. The dimension of PAN-BNPs nanofiber can be tunable from (0.09 ± 0.03)μm to (0.81 ± 0.11)μm by controlling the PAN and BNPs concentrations in precursors. The optimized PAN-BNPs nanofiber air filter with a basis weight of 1 g m^-2demonstrates the attractive attributes of high PM_2.5removal efficiency up to 99.962% and low pressure drop of 58 Pa. Most importantly, after introducing the BNPs as electret, the removal efficiency is very stable under the air flow rate of 6 l min^-1. This PAN-BNPs nanofiber with a long electrostatic duration time offers an approach for fabricating future high-performance air filters.

Gradient structured micro/nanofibrous sponges with superior compressibility and stretchability for broadband sound absorption

Ultrafine fibrous porous materials obtained by electrospinning technology have broad application prospects in the field of noise reduction. However, the two-dimensional fibrous membranes faced low thickness and dense structure, resulting in a single internal structure and narrow sound absorption band. Here, we report a simple and robust strategy to prepare gradient structured fiber sponges with superelasticity and stretchability by combining humidity-assisted multi-step electrospinning and a unique physical/chemical dual cross-linking method. The prepared gradient structured fibrous sponge has a maximum tensile strength of 169 kPa and can lift a weight 10,000 times its weight without breaking. Besides, the material can still maintain a stable structure after 500 compression cycles at 60% strain. Meantime, the material has lightweight properties (density of 13.8 mg cm^-3) and hydrophobicity (water contact angle of 152°). More importantly, the gradient change of porosity and pore diameter in the Z direction endowed the fibrous sponge material with high-efficiency absorption of broadband sound waves (with a noise reduction coefficient up to 0.53). The design of this gradient structured fiber sponge opens a new way for the development of ideal sound-absorbing materials.

Preparation and Applications of Electrospun Optically Transparent Fibrous Membrane

The optically transparent electrospun fibrous membrane has been widely used in many fields due to its simple operation, flexible design, controllable structure, high specific surface area, high porosity, and unique excellent optical properties. This paper comprehensively summarizes the preparation methods and applications of an electrospun optically transparent fibrous membrane in view of the selection of raw materials and structure modulation during preparation. We start by the factors that affect transmittance among different materials and explain the light transmission mechanism of the fibrous membrane. This paper also provides an overview of the methods to fabricate a transparent nanofibrous membrane based on the electrospinning technology including direct electrospinning, solution treatment after electrospinning, heat treatment after electrospinning, and surface modification after electrospinning. It further summarizes the differences in the processes and mechanisms between different transparent fibrous membranes prepared by different methods. Additionally, we study the utilization of transparent as-spun membranes as flexible functional materials, namely alcohol dipstick, air purification, self-cleaning materials, biomedicine, sensors, energy and optoelectronics, oil-water separation, food packaging, anti-icing coating, and anti-corrosion materials. It demonstrates the high transparency of the nanofibers' effects on the applications as well as upgrades the product performance.

Model-Based Fiber Diameter Determination Approach to Fine Particulate Matter Fraction (PM2.5) Removal in HVAC Systems

Particulate Matter (PM) is a general term to classify air pollutants consisting of airborne particles. The particles vary in composition and size, and the sizes of particles range from 2.5 µm (PM2.5) to 10 µm (PM10). Anthropogenic activity (e.g., industrial processes or fuel/waste combustion) stands as the main emission source of PM. Due to the fact that indoor PM penetrates from the outside to indoor air, Heating, Ventilation, and Air-Conditioning (HVAC) filtration systems may play a significant role in decreasing air pollution indoors. The section of the respiratory tract affected by particulate matter depends on the particle size. The smaller the fraction, the more deeply it can enter into lungs and bronchi, causing a series of health problems. Conventional electret air filters applied in HVAC systems are not able to efficiently remove PM2.5 (e.g., huge gaps between thick fibers and unintentional elimination of electrostatic effects). The electrospinning process allows for the production of fibers of diverse diameters, including ultrathin yarns. The following work presents the axial length scale χχ  estimation method for the given conditions and experimental results. According to this approach, it is possible to find out what parameters should be used to produce materials at certain fiber diameters and to capture fine particulate matter fractions (PM2.5). This research refers to poly(acrylonitrile) (PAN) fibers. The most important advantages, limitations, and challenges of the presented methodology are detected and discussed in this work.